[PATCHv2 0/2] Initial support for OMAP3EVM

[PATCHv2 0/2] Initial support for OMAP3EVM

[Sanjeev Premi]

This patchset provides a minimal support to get u-boot-v2
working on the OMAP3EVM.

This is just a merge of patches from earlier version, as requested.

Sanjeev Premi (2):
  omap3evm: Add basic support for the board
  omap3evm: Minimal default configuration

 arch/arm/configs/omap3_evm_defconfig |  197 ++++++++++++++++++++++++
 board/omap/Kconfig                   |   27 ++++
 board/omap/Makefile                  |    1 +
 board/omap/board-omap3evm.c          |  275 ++++++++++++++++++++++++++++++++++
 4 files changed, 500 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/configs/omap3_evm_defconfig
 create mode 100644 board/omap/board-omap3evm.c


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 1/2] omap3evm: Add basic support for the board

[Sanjeev Premi]

This patch adds support for OMAP3EVM. It does
the following:
 - Adds OMAP3EVM as an option in Kconfig.
 - Adds choice for UART1/UART3 for serial console
 - Minimal initializations for the board
 - Updates to makefile

Signed-off-by: Sanjeev Premi <premi@ti.com>
---
 board/omap/Kconfig          |   27 ++++
 board/omap/Makefile         |    1 +
 board/omap/board-omap3evm.c |  275 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 303 insertions(+), 0 deletions(-)
 create mode 100644 board/omap/board-omap3evm.c

diff --git a/board/omap/Kconfig b/board/omap/Kconfig
index 07ba87c..361bed4 100644
--- a/board/omap/Kconfig
+++ b/board/omap/Kconfig
@@ -30,6 +30,7 @@ menu "OMAP Platform Features"
 config BOARDINFO
 	default "Texas Instrument's SDP343x" if MACH_OMAP343xSDP
 	default "Texas Instrument's Beagle" if MACH_BEAGLE
+	default "Texas Instrument's OMAP3EVM" if MACH_OMAP3EVM
 
 choice
 	prompt "Select OMAP platform"
@@ -50,8 +51,34 @@ config MACH_BEAGLE
 	  help
 	  Say Y here if you are using Beagle Board
 
+config MACH_OMAP3EVM
+	bool "Texas Instrument's OMAP3 EVM"
+	select MACH_HAS_LOWLEVEL_INIT
+	select OMAP_CLOCK_ALL
+	select HAS_OMAP_NAND
+	  help
+	  Say Y here if you are using OMAP3EVM
+
 endchoice
 
+if MACH_OMAP3EVM
+	choice
+	prompt "Select UART"
+
+	config OMAP3EVM_UART1
+		bool "Use UART1"
+		depends on MACH_OMAP3EVM
+		help
+		  Say Y here if you would like to use UART1 as console.
+
+	config OMAP3EVM_UART3
+		bool "Use UART3"
+		depends on MACH_OMAP3EVM
+		help
+		  Say Y here if you would like to use UART3 as console.
+	endchoice
+endif
+
 config MACH_OMAP_ADVANCED_MUX
 	bool "Enable advanced pin muxing"
 	depends on MACH_OMAP343xSDP
diff --git a/board/omap/Makefile b/board/omap/Makefile
index 002855a..b4bb3e1 100644
--- a/board/omap/Makefile
+++ b/board/omap/Makefile
@@ -23,5 +23,6 @@
 obj-$(CONFIG_MACH_DO_LOWLEVEL_INIT) += platform.o
 obj-$(CONFIG_MACH_OMAP343xSDP) += board-sdp343x.o
 obj-$(CONFIG_MACH_BEAGLE) += board-beagle.o
+obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o
 obj-$(CONFIG_MACH_OMAP_GPMC_GENERICNAND) += devices-gpmc-nand.o
 
diff --git a/board/omap/board-omap3evm.c b/board/omap/board-omap3evm.c
new file mode 100644
index 0000000..fdea0ff
--- /dev/null
+++ b/board/omap/board-omap3evm.c
@@ -0,0 +1,275 @@
+/**
+ * @file
+ * @brief Board Initialization routines for OMAP3EVM.
+ *
+ * FileName: board/omap/board-omap3evm.c
+ *
+ * This board is based on OMAP3530.
+ * More on OMAP3530 (including documentation can be found here):
+ * http://focus.ti.com/docs/prod/folders/print/omap3530.html
+ *
+ * This file provides initialization in two stages:
+ * @li Boot time initialization - just get SDRAM working.
+ * This is run from SRAM - so no case constructs and global vars can be used.
+ * @li Run time initialization - this is for the rest of the initializations
+ * such as flash, uart etc.
+ *
+ * Boot time initialization includes:
+ * @li SDRAM initialization.
+ * @li Pin Muxing relevant for the EVM.
+ *
+ * Run time initialization includes
+ * @li serial @ref serial_ns16550.c driver device definition
+ *
+ * Originally from board/omap/board-beagle.c
+ */
+
+/*
+ * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
+ * Sanjeev Premi <premi@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <console.h>
+#include <init.h>
+#include <driver.h>
+#include <asm/io.h>
+#include <ns16550.h>
+#include <asm/armlinux.h>
+#include <mach/silicon.h>
+#include <mach/sdrc.h>
+#include <mach/sys_info.h>
+#include <mach/syslib.h>
+#include <mach/control.h>
+#include <mach/omap3-mux.h>
+#include <mach/gpmc.h>
+#include "board.h"
+
+
+/*
+ * Boot-time initialization(s)
+ */
+
+/**
+ * @brief Initialize the SDRC module
+ *
+ * @return void
+ */
+static void sdrc_init(void)
+{
+	/* SDRAM software reset */
+	/* No idle ack and RESET enable */
+	writel(0x1A, SDRC_REG(SYSCONFIG));
+	sdelay(100);
+	/* No idle ack and RESET disable */
+	writel(0x18, SDRC_REG(SYSCONFIG));
+
+	/* SDRC Sharing register */
+	/* 32-bit SDRAM on data lane [31:0] - CS0 */
+	/* pin tri-stated = 1 */
+	writel(0x00000100, SDRC_REG(SHARING));
+
+	/* ----- SDRC Registers Configuration --------- */
+	/* SDRC_MCFG0 register */
+	writel(0x02584099, SDRC_REG(MCFG_0));
+
+	/* SDRC_RFR_CTRL0 register */
+	writel(0x54601, SDRC_REG(RFR_CTRL_0));
+
+	/* SDRC_ACTIM_CTRLA0 register */
+	writel(0xA29DB4C6, SDRC_REG(ACTIM_CTRLA_0));
+
+	/* SDRC_ACTIM_CTRLB0 register */
+	writel(0x12214, SDRC_REG(ACTIM_CTRLB_0));
+
+	/* Disble Power Down of CKE due to 1 CKE on combo part */
+	writel(0x00000081, SDRC_REG(POWER));
+
+	/* SDRC_MANUAL command register */
+	/* NOP command */
+	writel(0x00000000, SDRC_REG(MANUAL_0));
+	/* Precharge command */
+	writel(0x00000001, SDRC_REG(MANUAL_0));
+	/* Auto-refresh command */
+	writel(0x00000002, SDRC_REG(MANUAL_0));
+	/* Auto-refresh command */
+	writel(0x00000002, SDRC_REG(MANUAL_0));
+
+	/* SDRC MR0 register Burst length=4 */
+	writel(0x00000032, SDRC_REG(MR_0));
+
+	/* SDRC DLLA control register */
+	writel(0x0000000A, SDRC_REG(DLLA_CTRL));
+
+	return;
+}
+
+/**
+ * @brief Do the necessary pin muxing required for OMAP3EVM. Some pins in OMAP3
+ * do not have alternate modes. We don't program these pins.
+ *
+ * See @ref MUX_VAL for description of the muxing mode.
+ *
+ * @return void
+ */
+static void mux_config(void)
+{
+	/*
+	 * SDRC
+	 * - SDRC_D0-SDRC_D31: Default MUX mode is mode0.
+	 */
+
+	/*
+	 * GPMC
+	 * - GPMC_D0-GPMC_D7: Default MUX mode is mode0.
+	 * - GPMC_NADV_ALE: Default MUX mode is mode0.
+	 * - GPMC_NOE: Default MUX mode is mode0.
+	 * - GPMC_NWE: Default MUX mode is mode0.
+	 * - GPMC_WAIT0: Default MUX mode is mode0.
+	 */
+	MUX_VAL(CP(GPMC_A1),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A2),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A3),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A4),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A5),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A6),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A7),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A8),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A9),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_A10),		(IDIS | PTD | DIS | M0));
+
+	MUX_VAL(CP(GPMC_D8),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_D9),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_D10),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_D11),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_D12),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_D13),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_D14),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_D15),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_CLK),		(IDIS | PTD | DIS | M0));
+
+	MUX_VAL(CP(GPMC_NBE0_CLE),	(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_NBE1),		(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(GPMC_NWP),		(IEN  | PTD | DIS | M0));
+
+	MUX_VAL(CP(GPMC_WAIT1),		(IEN  | PTU | EN  | M0));
+
+	/*
+	 * Serial Interface
+	 */
+#if defined(CONFIG_OMAP3EVM_UART1)
+	MUX_VAL(CP(UART1_TX),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(UART1_RTS),		(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(UART1_CTS),		(IEN  | PTU | DIS | M0));
+	MUX_VAL(CP(UART1_RX),		(IEN  | PTD | DIS | M0));
+#elif defined(CONFIG_OMAP3EVM_UART3)
+	MUX_VAL(CP(UART3_CTS_RCTX),	(IEN  | PTD | EN  | M0));
+	MUX_VAL(CP(UART3_RTS_SD),	(IDIS | PTD | DIS | M0));
+	MUX_VAL(CP(UART3_RX_IRRX),	(IEN  | PTD | DIS | M0));
+	MUX_VAL(CP(UART3_TX_IRTX),	(IDIS | PTD | DIS | M0));
+#endif
+}
+
+/**
+ * @brief The basic entry point for board initialization.
+ *
+ * This is called as part of machine init (after arch init).
+ * This is again called with stack in SRAM, so not too many
+ * constructs possible here.
+ *
+ * @return void
+ */
+void board_init(void)
+{
+	int in_sdram = running_in_sdram();
+
+	mux_config();
+	/* Dont reconfigure SDRAM while running in SDRAM! */
+	if (!in_sdram)
+		sdrc_init();
+}
+
+/*
+ * Run-time initialization(s)
+ */
+
+#ifdef CONFIG_DRIVER_SERIAL_NS16550
+
+static struct NS16550_plat serial_plat = {
+	.clock		= 48000000,      /* 48MHz (APLL96/2) */
+	.f_caps		= CONSOLE_STDIN | CONSOLE_STDOUT | CONSOLE_STDERR,
+	.reg_read	= omap_uart_read,
+	.reg_write	= omap_uart_write,
+};
+
+static struct device_d omap3evm_serial_device = {
+	.name		= "serial_ns16550",
+#if defined(CONFIG_OMAP3EVM_UART1)
+	.map_base	= OMAP_UART1_BASE,
+#elif defined(CONFIG_OMAP3EVM_UART3)
+	.map_base	= OMAP_UART3_BASE,
+#endif
+	.size		= 1024,
+	.platform_data	= (void *)&serial_plat,
+};
+
+/**
+ * @brief Initialize the serial port to be used as console.
+ *
+ * @return result of device registration
+ */
+static int omap3evm_init_console(void)
+{
+	return register_device(&omap3evm_serial_device);
+}
+console_initcall(omap3evm_init_console);
+#endif /* CONFIG_DRIVER_SERIAL_NS16550 */
+
+static struct memory_platform_data sram_pdata = {
+	.name	= "ram0",
+	.flags	= DEVFS_RDWR,
+};
+
+static struct device_d sdram_dev = {
+	.name		= "mem",
+	.map_base	= 0x80000000,
+	.size		= 128 * 1024 * 1024,
+	.platform_data	= &sram_pdata,
+};
+
+static int omap3evm_init_devices(void)
+{
+	int ret;
+
+	ret = register_device(&sdram_dev);
+	if (ret)
+		goto failed;
+
+#ifdef CONFIG_GPMC
+	/*
+	 * WP is made high and WAIT1 active Low
+	 */
+	gpmc_generic_init(0x10);
+#endif
+
+	armlinux_add_dram(&sdram_dev);
+
+failed:
+	return ret;
+}
+device_initcall(omap3evm_init_devices);
-- 
1.6.2.2


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 2/2] omap3evm: Minimal default configuration

[Sanjeev Premi]

Created a minimal configuration that just gets the
board up and running.

Signed-off-by: Sanjeev Premi <premi@ti.com>
---
 arch/arm/configs/omap3_evm_defconfig |  197 ++++++++++++++++++++++++++++++++++
 1 files changed, 197 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/configs/omap3_evm_defconfig

diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig
new file mode 100644
index 0000000..99d1198
--- /dev/null
+++ b/arch/arm/configs/omap3_evm_defconfig
@@ -0,0 +1,197 @@
+#
+# Automatically generated make config: don't edit
+# U-Boot version: 2.0.0-rc10
+# Mon Dec 14 16:16:09 2009
+#
+CONFIG_GENERIC_LINKER_SCRIPT=y
+CONFIG_ARM=y
+
+#
+# System Type
+#
+CONFIG_ARCH_OMAP=y
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_V7=y
+CONFIG_CPU_32v7=y
+
+#
+# processor features
+#
+CONFIG_ARCH_TEXT_BASE=0x80e80000
+CONFIG_BOARDINFO="Texas Instrument's OMAP3EVM"
+
+#
+# OMAP Features
+#
+CONFIG_ARCH_OMAP3=y
+CONFIG_OMAP_CONFIG_STACKSIZE=0x00008000
+CONFIG_OMAP_MALLOC_LEN=0x00008000
+CONFIG_OMAP_CLOCK_ALL=y
+CONFIG_OMAP_CLOCK_SOURCE_S32K=y
+CONFIG_OMAP3_CLOCK_CONFIG=y
+# CONFIG_OMAP3_COPY_CLOCK_SRAM is not set
+CONFIG_GPMC=y
+
+#
+# OMAP Platform Features
+#
+CONFIG_MACH_OMAP3EVM=y
+CONFIG_OMAP3EVM_UART1=y
+# CONFIG_OMAP3EVM_UART3 is not set
+CONFIG_HAS_OMAP_NAND=y
+CONFIG_AEABI=y
+
+#
+# Arm specific settings
+#
+CONFIG_CMD_ARM_CPUINFO=y
+# CONFIG_CMDLINE_TAG is not set
+# CONFIG_SETUP_MEMORY_TAGS is not set
+# CONFIG_INITRD_TAG is not set
+# CONFIG_CPU_V7_DCACHE_SKIP is not set
+CONFIG_HAS_KALLSYMS=y
+CONFIG_HAS_MODULES=y
+# CONFIG_CMD_MEMORY is not set
+
+#
+# General Settings
+#
+CONFIG_LOCALVERSION_AUTO=y
+
+#
+# memory layout
+#
+CONFIG_HAVE_CONFIGURABLE_TEXT_BASE=y
+CONFIG_TEXT_BASE=0x40200000
+CONFIG_HAVE_CONFIGURABLE_MEMORY_LAYOUT=y
+# CONFIG_MEMORY_LAYOUT_DEFAULT is not set
+CONFIG_MEMORY_LAYOUT_FIXED=y
+CONFIG_STACK_BASE=0x87BF7F10
+CONFIG_STACK_SIZE=0x8000
+CONFIG_MALLOC_BASE=0x87BFFF10
+CONFIG_MALLOC_SIZE=0x400000
+# CONFIG_BROKEN is not set
+# CONFIG_EXPERIMENTAL is not set
+CONFIG_MACH_HAS_LOWLEVEL_INIT=y
+CONFIG_MACH_DO_LOWLEVEL_INIT=y
+CONFIG_ARCH_HAS_LOWLEVEL_INIT=y
+CONFIG_PROMPT="OMAP3_EVM> "
+CONFIG_BAUDRATE=115200
+CONFIG_SIMPLE_READLINE=y
+CONFIG_LONGHELP=y
+CONFIG_CBSIZE=1024
+CONFIG_MAXARGS=16
+# CONFIG_SHELL_HUSH is not set
+CONFIG_SHELL_SIMPLE=y
+# CONFIG_CMDLINE_EDITING is not set
+# CONFIG_ERRNO_MESSAGES is not set
+# CONFIG_TIMESTAMP is not set
+CONFIG_CONSOLE_FULL=y
+CONFIG_CONSOLE_ACTIVATE_FIRST=y
+# CONFIG_OF_FLAT_TREE is not set
+# CONFIG_PARTITION is not set
+# CONFIG_DEFAULT_ENVIRONMENT is not set
+
+#
+# Debugging
+#
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_ENABLE_FLASH_NOISE is not set
+# CONFIG_ENABLE_PARTITION_NOISE is not set
+# CONFIG_ENABLE_DEVICE_NOISE is not set
+
+#
+# Commands
+#
+
+#
+# scripting
+#
+# CONFIG_CMD_EDIT is not set
+# CONFIG_CMD_EXEC is not set
+# CONFIG_CMD_SLEEP is not set
+# CONFIG_CMD_SAVEENV is not set
+# CONFIG_CMD_LOADENV is not set
+# CONFIG_CMD_EXPORT is not set
+# CONFIG_CMD_PRINTENV is not set
+# CONFIG_CMD_READLINE is not set
+CONFIG_CMD_TRUE=y
+CONFIG_CMD_FALSE=y
+
+#
+# file commands
+#
+CONFIG_CMD_LS=y
+# CONFIG_CMD_RM is not set
+# CONFIG_CMD_CAT is not set
+# CONFIG_CMD_MKDIR is not set
+# CONFIG_CMD_RMDIR is not set
+# CONFIG_CMD_CP is not set
+CONFIG_CMD_PWD=y
+CONFIG_CMD_CD=y
+# CONFIG_CMD_MOUNT is not set
+# CONFIG_CMD_UMOUNT is not set
+
+#
+# console
+#
+CONFIG_CMD_CLEAR=y
+CONFIG_CMD_ECHO=y
+
+#
+# memory
+#
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_MEMINFO=y
+# CONFIG_CMD_CRC is not set
+# CONFIG_CMD_MTEST is not set
+
+#
+# flash
+#
+
+#
+# booting
+#
+# CONFIG_CMD_BOOTM is not set
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_BOOTU=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_GO=y
+# CONFIG_CMD_TIMEOUT is not set
+# CONFIG_CMD_PARTITION is not set
+CONFIG_CMD_VERSION=y
+CONFIG_CMD_HELP=y
+CONFIG_CMD_DEVINFO=y
+# CONFIG_NET is not set
+
+#
+# Drivers
+#
+
+#
+# serial drivers
+#
+CONFIG_DRIVER_SERIAL_NS16550=y
+CONFIG_DRIVER_SERIAL_NS16550_OMAP_EXTENSIONS=y
+
+#
+# SPI drivers
+#
+# CONFIG_SPI is not set
+
+#
+# flash drivers
+#
+
+
+#
+# Filesystem support
+#
+# CONFIG_FS_CRAMFS is not set
+CONFIG_FS_RAMFS=y
+CONFIG_FS_DEVFS=y
+CONFIG_CRC16=y
-- 
1.6.2.2


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

Re: [PATCHv2 0/2] Initial support for OMAP3EVM

[Sascha Hauer]

On Thu, Dec 17, 2009 at 03:21:12PM +0530, Sanjeev Premi wrote:
> This patchset provides a minimal support to get u-boot-v2
> working on the OMAP3EVM.
> 
> This is just a merge of patches from earlier version, as requested.

Ok, applied

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox