* [PATCH 01/11] imx: Separate framebuffer platformdata and the videomode
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 17:46 ` Sascha Hauer
2010-10-22 16:53 ` [PATCH 02/11] Add more flags for sync control Juergen Beisert
` (9 subsequent siblings)
10 siblings, 1 reply; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
This patch separates the imx platformdata and its videomode in two structures,
in order to support more than one defined videomode in the boardfile. This
is intended to support runtime videomode selection later on. It also uses
now the same videomode setup style than the imx-fpu based systems (like the
i.MX35).
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c | 28 +++++++++--------
arch/arm/boards/eukrea_cpuimx27/eukrea_cpuimx27.c | 28 +++++++++--------
arch/arm/boards/guf-neso/board.c | 28 +++++++++--------
arch/arm/boards/imx21ads/imx21ads.c | 34 +++++++++++----------
arch/arm/boards/pcm038/pcm038.c | 28 +++++++++--------
arch/arm/mach-imx/include/mach/imxfb.h | 2 +-
drivers/video/imx.c | 6 ++--
7 files changed, 82 insertions(+), 72 deletions(-)
diff --git a/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c b/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
index 805ffe2..032897a 100644
--- a/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
+++ b/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
@@ -120,20 +120,22 @@ static struct device_d nand_dev = {
.platform_data = &nand_info,
};
+static struct fb_videomode cmo_display = {
+ .name = "CMO-QVGA",
+ .refresh = 60,
+ .xres = 320,
+ .yres = 240,
+ .pixclock = KHZ2PICOS(6500),
+ .hsync_len = 30,
+ .left_margin = 38,
+ .right_margin = 20,
+ .vsync_len = 3,
+ .upper_margin = 15,
+ .lower_margin = 4,
+};
+
static struct imx_fb_videomode imxfb_mode = {
- .mode = {
- .name = "CMO-QVGA",
- .refresh = 60,
- .xres = 320,
- .yres = 240,
- .pixclock = KHZ2PICOS(6500),
- .hsync_len = 30,
- .left_margin = 38,
- .right_margin = 20,
- .vsync_len = 3,
- .upper_margin = 15,
- .lower_margin = 4,
- },
+ .mode = &cmo_display,
.pcr = 0xCAD08B80,
.bpp = 16,
};
diff --git a/arch/arm/boards/eukrea_cpuimx27/eukrea_cpuimx27.c b/arch/arm/boards/eukrea_cpuimx27/eukrea_cpuimx27.c
index 62fc14e..3ea2466 100644
--- a/arch/arm/boards/eukrea_cpuimx27/eukrea_cpuimx27.c
+++ b/arch/arm/boards/eukrea_cpuimx27/eukrea_cpuimx27.c
@@ -186,20 +186,22 @@ static void eukrea_cpuimx27_mmu_init(void)
#endif
#ifdef CONFIG_DRIVER_VIDEO_IMX
+static struct fb_videomode cmo_display = {
+ .name = "CMO-QVGA",
+ .refresh = 60,
+ .xres = 320,
+ .yres = 240,
+ .pixclock = 156000,
+ .hsync_len = 30,
+ .left_margin = 38,
+ .right_margin = 20,
+ .vsync_len = 3,
+ .upper_margin = 15,
+ .lower_margin = 4,
+};
+
static struct imx_fb_videomode imxfb_mode = {
- .mode = {
- .name = "CMO-QVGA",
- .refresh = 60,
- .xres = 320,
- .yres = 240,
- .pixclock = 156000,
- .hsync_len = 30,
- .left_margin = 38,
- .right_margin = 20,
- .vsync_len = 3,
- .upper_margin = 15,
- .lower_margin = 4,
- },
+ .mode = &cmo_display,
.pcr = 0xFAD08B80,
.bpp = 16,};
diff --git a/arch/arm/boards/guf-neso/board.c b/arch/arm/boards/guf-neso/board.c
index 9c85c08..6949675 100644
--- a/arch/arm/boards/guf-neso/board.c
+++ b/arch/arm/boards/guf-neso/board.c
@@ -91,20 +91,22 @@ static struct device_d nand_dev = {
.platform_data = &nand_info,
};
+static struct fb_videomode cpt_display = {
+ .name = "CPT CLAA070LC0JCT",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = KHZ2PICOS(27000),
+ .hsync_len = 1, /* DE only sync */
+ .left_margin = 50,
+ .right_margin = 50,
+ .vsync_len = 1, /* DE only sync */
+ .upper_margin = 10,
+ .lower_margin = 10,
+};
+
static struct imx_fb_videomode imxfb_mode = {
- .mode = {
- .name = "CPT CLAA070LC0JCT",
- .refresh = 60,
- .xres = 800,
- .yres = 480,
- .pixclock = KHZ2PICOS(27000),
- .hsync_len = 1, /* DE only sync */
- .left_margin = 50,
- .right_margin = 50,
- .vsync_len = 1, /* DE only sync */
- .upper_margin = 10,
- .lower_margin = 10,
- },
+ .mode = &cpt_display,
/*
* - TFT style panel
* - clk enabled while idle
diff --git a/arch/arm/boards/imx21ads/imx21ads.c b/arch/arm/boards/imx21ads/imx21ads.c
index 44d37aa..81006de 100644
--- a/arch/arm/boards/imx21ads/imx21ads.c
+++ b/arch/arm/boards/imx21ads/imx21ads.c
@@ -79,24 +79,26 @@ static struct device_d cs8900_dev = {
// IRQ is connected to UART3_RTS
};
+static struct fb_videomode sharp_display = {
+ .name = "Sharp-LQ035Q7",
+ .refresh = 60,
+ .xres = 240,
+ .yres = 320,
+ .pixclock = 188679,
+ .left_margin = 6,
+ .right_margin = 16,
+ .upper_margin = 8,
+ .lower_margin = 10,
+ .hsync_len = 2,
+ .vsync_len = 1,
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ .flag = 0,
+};
+
/* Sharp LQ035Q7DB02 QVGA display */
static struct imx_fb_videomode imx_fb_modedata = {
- .mode = {
- .name = "Sharp-LQ035Q7",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 188679,
- .left_margin = 6,
- .right_margin = 16,
- .upper_margin = 8,
- .lower_margin = 10,
- .hsync_len = 2,
- .vsync_len = 1,
- .sync = 0,
- .vmode = FB_VMODE_NONINTERLACED,
- .flag = 0,
- },
+ .mode = &sharp_display,
.pcr = 0xfb108bc7,
.bpp = 16,
};
diff --git a/arch/arm/boards/pcm038/pcm038.c b/arch/arm/boards/pcm038/pcm038.c
index 3a9b413..026e9c0 100644
--- a/arch/arm/boards/pcm038/pcm038.c
+++ b/arch/arm/boards/pcm038/pcm038.c
@@ -127,20 +127,22 @@ static struct device_d nand_dev = {
.platform_data = &nand_info,
};
+static struct fb_videomode sharp_display = {
+ .name = "Sharp-LQ035Q7",
+ .refresh = 60,
+ .xres = 240,
+ .yres = 320,
+ .pixclock = 188679, /* in ps (5.3MHz) */
+ .hsync_len = 7,
+ .left_margin = 5,
+ .right_margin = 16,
+ .vsync_len = 1,
+ .upper_margin = 7,
+ .lower_margin = 9,
+};
+
static struct imx_fb_videomode imxfb_mode = {
- .mode = {
- .name = "Sharp-LQ035Q7",
- .refresh = 60,
- .xres = 240,
- .yres = 320,
- .pixclock = 188679, /* in ps (5.3MHz) */
- .hsync_len = 7,
- .left_margin = 5,
- .right_margin = 16,
- .vsync_len = 1,
- .upper_margin = 7,
- .lower_margin = 9,
- },
+ .mode = &sharp_display,
/*
* - HSYNC active high
* - VSYNC active high
diff --git a/arch/arm/mach-imx/include/mach/imxfb.h b/arch/arm/mach-imx/include/mach/imxfb.h
index 16b43ea..7baa244 100644
--- a/arch/arm/mach-imx/include/mach/imxfb.h
+++ b/arch/arm/mach-imx/include/mach/imxfb.h
@@ -50,7 +50,7 @@
#define DMACR_TM(x) ((x) & 0xf)
struct imx_fb_videomode {
- struct fb_videomode mode;
+ struct fb_videomode *mode;
u32 pcr;
unsigned char bpp;
};
diff --git a/drivers/video/imx.c b/drivers/video/imx.c
index ac51858..6ccd77e 100644
--- a/drivers/video/imx.c
+++ b/drivers/video/imx.c
@@ -555,9 +555,9 @@ static int imxfb_probe(struct device_d *dev)
fbi->enable = pdata->enable;
fbi->dev = dev;
info->priv = fbi;
- info->mode = &pdata->mode->mode;
- info->xres = pdata->mode->mode.xres;
- info->yres = pdata->mode->mode.yres;
+ info->mode = pdata->mode->mode;
+ info->xres = pdata->mode->mode->xres;
+ info->yres = pdata->mode->mode->yres;
info->bits_per_pixel = pdata->mode->bpp;
info->fbops = &imxfb_ops;
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 01/11] imx: Separate framebuffer platformdata and the videomode
2010-10-22 16:53 ` [PATCH 01/11] imx: Separate framebuffer platformdata and the videomode Juergen Beisert
@ 2010-10-22 17:46 ` Sascha Hauer
2010-10-23 10:31 ` Juergen Beisert
0 siblings, 1 reply; 23+ messages in thread
From: Sascha Hauer @ 2010-10-22 17:46 UTC (permalink / raw)
To: Juergen Beisert; +Cc: barebox
On Fri, Oct 22, 2010 at 06:53:15PM +0200, Juergen Beisert wrote:
> This patch separates the imx platformdata and its videomode in two structures,
> in order to support more than one defined videomode in the boardfile. This
> is intended to support runtime videomode selection later on. It also uses
> now the same videomode setup style than the imx-fpu based systems (like the
> i.MX35).
>
> Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
> ---
> arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c | 28 +++++++++--------
> arch/arm/boards/eukrea_cpuimx27/eukrea_cpuimx27.c | 28 +++++++++--------
> arch/arm/boards/guf-neso/board.c | 28 +++++++++--------
> arch/arm/boards/imx21ads/imx21ads.c | 34 +++++++++++----------
> arch/arm/boards/pcm038/pcm038.c | 28 +++++++++--------
> arch/arm/mach-imx/include/mach/imxfb.h | 2 +-
> drivers/video/imx.c | 6 ++--
> 7 files changed, 82 insertions(+), 72 deletions(-)
>
> diff --git a/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c b/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
> index 805ffe2..032897a 100644
> --- a/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
> +++ b/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
> @@ -120,20 +120,22 @@ static struct device_d nand_dev = {
> .platform_data = &nand_info,
> };
>
> +static struct fb_videomode cmo_display = {
> + .name = "CMO-QVGA",
> + .refresh = 60,
> + .xres = 320,
> + .yres = 240,
> + .pixclock = KHZ2PICOS(6500),
> + .hsync_len = 30,
> + .left_margin = 38,
> + .right_margin = 20,
> + .vsync_len = 3,
> + .upper_margin = 15,
> + .lower_margin = 4,
> +};
> +
> static struct imx_fb_videomode imxfb_mode = {
> - .mode = {
> - .name = "CMO-QVGA",
> - .refresh = 60,
> - .xres = 320,
> - .yres = 240,
> - .pixclock = KHZ2PICOS(6500),
> - .hsync_len = 30,
> - .left_margin = 38,
> - .right_margin = 20,
> - .vsync_len = 3,
> - .upper_margin = 15,
> - .lower_margin = 4,
> - },
> + .mode = &cmo_display,
> .pcr = 0xCAD08B80,
> .bpp = 16,
> };
What are we going to do about the .pcr value? It is display specific.
Look for example in pcm970-baseboard.c in the kernel. It has two
different possible displays with two different pcr values.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 01/11] imx: Separate framebuffer platformdata and the videomode
2010-10-22 17:46 ` Sascha Hauer
@ 2010-10-23 10:31 ` Juergen Beisert
0 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-23 10:31 UTC (permalink / raw)
To: barebox
Sascha Hauer wrote:
> On Fri, Oct 22, 2010 at 06:53:15PM +0200, Juergen Beisert wrote:
> > This patch separates the imx platformdata and its videomode in two
> > structures, in order to support more than one defined videomode in the
> > boardfile. This is intended to support runtime videomode selection later
> > on. It also uses now the same videomode setup style than the imx-fpu
> > based systems (like the i.MX35).
> >
> > Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
> > ---
> > arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c | 28
> > +++++++++-------- arch/arm/boards/eukrea_cpuimx27/eukrea_cpuimx27.c |
> > 28 +++++++++-------- arch/arm/boards/guf-neso/board.c |
> > 28 +++++++++-------- arch/arm/boards/imx21ads/imx21ads.c |
> > 34 +++++++++++---------- arch/arm/boards/pcm038/pcm038.c
> > | 28 +++++++++-------- arch/arm/mach-imx/include/mach/imxfb.h
> > | 2 +-
> > drivers/video/imx.c | 6 ++--
> > 7 files changed, 82 insertions(+), 72 deletions(-)
> >
> > diff --git a/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
> > b/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c index
> > 805ffe2..032897a 100644
> > --- a/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
> > +++ b/arch/arm/boards/eukrea_cpuimx25/eukrea_cpuimx25.c
> > @@ -120,20 +120,22 @@ static struct device_d nand_dev = {
> > .platform_data = &nand_info,
> > };
> >
> > +static struct fb_videomode cmo_display = {
> > + .name = "CMO-QVGA",
> > + .refresh = 60,
> > + .xres = 320,
> > + .yres = 240,
> > + .pixclock = KHZ2PICOS(6500),
> > + .hsync_len = 30,
> > + .left_margin = 38,
> > + .right_margin = 20,
> > + .vsync_len = 3,
> > + .upper_margin = 15,
> > + .lower_margin = 4,
> > +};
> > +
> > static struct imx_fb_videomode imxfb_mode = {
> > - .mode = {
> > - .name = "CMO-QVGA",
> > - .refresh = 60,
> > - .xres = 320,
> > - .yres = 240,
> > - .pixclock = KHZ2PICOS(6500),
> > - .hsync_len = 30,
> > - .left_margin = 38,
> > - .right_margin = 20,
> > - .vsync_len = 3,
> > - .upper_margin = 15,
> > - .lower_margin = 4,
> > - },
> > + .mode = &cmo_display,
> > .pcr = 0xCAD08B80,
> > .bpp = 16,
> > };
>
> What are we going to do about the .pcr value? It is display specific.
> Look for example in pcm970-baseboard.c in the kernel. It has two
> different possible displays with two different pcr values.
I will take a closer look what the meaning of this pcr value is. Maybe we can
create it at runtime from other flags given in the imx_fb_videomode.
Otherwise we could add a private pointer to the imx_fb_videomode structure,
which can point to platform and videomode specific data in a generic way.
jbe
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | Phone: +49-8766-939 228 |
Vertretung Sued/Muenchen, Germany | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de/ |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 02/11] Add more flags for sync control
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
2010-10-22 16:53 ` [PATCH 01/11] imx: Separate framebuffer platformdata and the videomode Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 16:53 ` [PATCH 03/11] Bring in dynamic videomode selection at runtime Juergen Beisert
` (8 subsequent siblings)
10 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
In order to make video mode setup and initializing a runtime job (currently
it is a compile time job) this patch tries to make the 'fb_videomode' structure
more generic. It should also carry special settings required only for some LC
displays. So, I add some additional sync flags to control the DE and CLCK to
the display (something a regular CRT does not know). Also the possibility to
stop the clock when outside active display data (required for (C)STN display).
Further suggestions for flags?
What about the special settings for some kind of Sharp displays the i.MX
processor family supports?
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
include/fb.h | 10 ++++++++++
1 files changed, 10 insertions(+), 0 deletions(-)
diff --git a/include/fb.h b/include/fb.h
index 379f931..218b244 100644
--- a/include/fb.h
+++ b/include/fb.h
@@ -17,11 +17,21 @@
/* vtotal = 144d/288n/576i => PAL */
/* vtotal = 121d/242n/484i => NTSC */
#define FB_SYNC_ON_GREEN 32 /* sync on green */
+/* LC display related settings */
+#define FB_SYNC_DE_HIGH_ACT (1 << 6)
+#define FB_SYNC_CLK_INVERT (1 << 7)
+#define FB_SYNC_DATA_INVERT (1 << 8)
+#define FB_SYNC_CLK_IDLE_EN (1 << 9)
+#define FB_SYNC_SWAP_RGB (1 << 10)
+#define FB_SYNC_CLK_SEL_EN (1 << 11)
+#define FB_SYNC_SHARP_MODE (1 << 31)
#define FB_VMODE_NONINTERLACED 0 /* non interlaced */
#define FB_VMODE_INTERLACED 1 /* interlaced */
#define FB_VMODE_DOUBLE 2 /* double scan */
#define FB_VMODE_ODD_FLD_FIRST 4 /* interlaced: top line first */
+/* LC display related settings */
+#define FB_VMODE_DUAL_SCAN 8
#define FB_VMODE_MASK 255
#define FB_VMODE_YWRAP 256 /* ywrap instead of panning */
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* [PATCH 03/11] Bring in dynamic videomode selection at runtime
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
2010-10-22 16:53 ` [PATCH 01/11] imx: Separate framebuffer platformdata and the videomode Juergen Beisert
2010-10-22 16:53 ` [PATCH 02/11] Add more flags for sync control Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 17:41 ` Sascha Hauer
2010-10-22 16:53 ` [PATCH 04/11] Remove the old videomode functions Juergen Beisert
` (7 subsequent siblings)
10 siblings, 1 reply; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
This patch mostly rewrites all parts of /drivers/video/fb.c. As it changes
the API to the drivers, it must be done in one step to keep the repository
bisectable. But to do it in one step makes the patches itself unreadable.
So, I decided to do it in a few steps, only for the review. All patches marked
with a "step n of m" should be merged, prior the final commit into the
repository.
This step brings in the required functions for dynamic videomode selection at
runtime, but keep the old functions untouched (the new ones are commented out).
This is patch 1 of 7 to keep the repository bisectable.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
drivers/video/Kconfig | 23 +++++
drivers/video/fb.c | 251 +++++++++++++++++++++++++++++++++++++++++++++++++
include/fb.h | 40 ++++++++
3 files changed, 314 insertions(+), 0 deletions(-)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 7a89a3f..e6ecfc8 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -5,6 +5,29 @@ menuconfig VIDEO
if VIDEO
+comment "runtime options"
+
+config VIDEO_DELAY_ENABLING
+ bool "Delayed enabling"
+ help
+ Say 'y' here to delay enabling video output. This is useful to first
+ fill the framebuffer (splash screen for example) prior enabling the
+ video device.
+ This entry adds the "enable" parameter to the video device, to enable
+ or disable video output at runtime.
+
+config VIDEO_DELAY_INIT
+ bool "Delayed initialization"
+ select VIDEO_DELAY_ENABLING
+ help
+ If the platform supports more than one video mode say 'y' her to delay
+ the initialization of the video device until any kind of barebox's
+ shell code sets up the correct mode at runtime.
+ This entry adds the "mode" parameter to the video device, to setup
+ the desired videomode prior enabling it at runtime.
+
+comment "drivers"
+
config DRIVER_VIDEO_IMX
bool "i.MX framebuffer driver"
depends on ARCH_IMX1 || ARCH_IMX21 || ARCH_IMX25 || ARCH_IMX27
diff --git a/drivers/video/fb.c b/drivers/video/fb.c
index f9a425e..c2934f6 100644
--- a/drivers/video/fb.c
+++ b/drivers/video/fb.c
@@ -1,3 +1,4 @@
+#include <init.h>
#include <common.h>
#include <fb.h>
#include <errno.h>
@@ -5,6 +6,8 @@
#include <getopt.h>
#include <fcntl.h>
#include <fs.h>
+#include <malloc.h>
+#include <xfuncs.h>
static int fb_ioctl(struct cdev* cdev, int req, void *data)
{
@@ -57,6 +60,141 @@ static int fb_enable_set(struct device_d *dev, struct param_d *param,
return 0;
}
+#if 0
+#ifdef CONFIG_VIDEO_DELAY_INIT
+static int fb_check_if_already_initialized(struct device_d *fb_dev)
+{
+ struct cdev *cdev = fb_dev->priv;
+ struct fb_info *info = cdev->priv;
+
+ if (info->active_mode != NULL) {
+ pr_err("Video mode '%s' is already set. Cannot change colour depth anymore.\n", info->active_mode->name);
+ return -EPERM;
+ }
+
+ return 0;
+}
+
+static int fb_cdepth_set(struct device_d *fb_dev, struct param_d *param, const char *val)
+{
+ struct cdev *cdev = fb_dev->priv;
+ struct fb_info *info = cdev->priv;
+ unsigned cdepth;
+ int rc;
+
+ rc = fb_check_if_already_initialized(fb_dev);
+ if (rc != 0)
+ return rc;
+
+ cdepth = simple_strtoul(val, NULL, 0);
+ if (cdepth != 0)
+ info->bits_per_pixel = cdepth;
+ else
+ return -EINVAL;
+
+ return dev_param_set_generic(fb_dev, param, val);
+}
+#endif
+
+#ifdef CONFIG_VIDEO_DELAY_ENABLING
+static int fb_enable_set(struct device_d *fb_dev, struct param_d *param, const char *val)
+{
+ struct cdev *cdev = fb_dev->priv;
+ struct fb_info *info = cdev->priv;
+ struct fb_host *host = fb_dev->platform_data;
+ int enable;
+ char *new;
+
+ if (!val)
+ return dev_param_set_generic(fb_dev, param, NULL);
+
+ enable = simple_strtoul(val, NULL, 0);
+
+ if (info->enabled == !!enable)
+ return 0;
+
+ if (enable) {
+ (host->fb_enable)(info);
+ new = "1";
+ } else {
+ (host->fb_disable)(info);
+ new = "0";
+ }
+
+ info->enabled = !!enable;
+
+ return dev_param_set_generic(fb_dev, param, new);
+}
+#endif
+
+static void fb_list_modes(struct fb_host *host)
+{
+ unsigned u;
+
+ if (host->mode_cnt == 0)
+ return;
+
+ printf(" Supported video mode(s):\n");
+ for (u = 0; u < host->mode_cnt; u++)
+ printf(" '%s'\n", host->mode[u].name);
+}
+
+static int fb_activate_mode(struct device_d *fb_dev, const struct fb_videomode *mode)
+{
+ struct cdev *cdev = fb_dev->priv;
+ struct fb_info *info = cdev->priv;
+ struct fb_host *host = fb_dev->platform_data;
+ int rc;
+
+ rc = (host->fb_mode)(info, mode);
+ if (rc != 0)
+ return rc;
+
+ info->active_mode = mode;
+ /*
+ * At this point of time we know the remaining information we need
+ * for the cdev and fb_info structure.
+ */
+ cdev->size = fb_dev->size;
+ info->xres = mode->xres;
+ info->yres = mode->yres;
+
+ return 0;
+}
+
+#ifdef CONFIG_VIDEO_DELAY_INIT
+static int fb_mode_set(struct device_d *fb_dev, struct param_d *param, const char *name)
+{
+ struct fb_host *host = fb_dev->platform_data;
+ unsigned u;
+ int rc;
+
+ pr_debug("%s called\n", __func__);
+
+ rc = fb_check_if_already_initialized(fb_dev);
+ if (rc != 0)
+ return rc;
+
+ /* Search for the requested video mode by name */
+ for (u = 0; u < host->mode_cnt; u++) {
+ if (!strcmp(host->mode[u].name, name))
+ break;
+ }
+ if (u >= host->mode_cnt) {
+ fb_list_modes(host); /* no mode with 'name' found */
+ return -ENODEV;
+ } else {
+ rc = fb_activate_mode(fb_dev, &host->mode[u]);
+ }
+
+ if (rc == 0)
+ dev_param_set_generic(fb_dev, param, name);
+
+ return rc;
+}
+#endif
+#endif
+
static struct file_operations fb_ops = {
.read = mem_read,
.write = mem_write,
@@ -65,6 +203,119 @@ static struct file_operations fb_ops = {
.ioctl = fb_ioctl,
};
+#if 0
+static int add_fb_parameter(struct device_d *fb_dev)
+{
+#ifdef CONFIG_VIDEO_DELAY_INIT
+ struct cdev *cdev = fb_dev->priv;
+ struct fb_info *info = cdev->priv;
+ char cd[10];
+
+ /** @todo provide base address parameter for the user */
+
+ dev_add_param(fb_dev, "cdepth", fb_cdepth_set, NULL, 0);
+ if (info->bits_per_pixel == 0) {
+ dev_set_param(fb_dev, "cdepth", "16");
+ info->bits_per_pixel = 16;
+ } else {
+ sprintf(cd, "%u", info->bits_per_pixel);
+ dev_set_param(fb_dev, "cdepth", cd);
+ }
+ dev_add_param(fb_dev, "mode", fb_mode_set, NULL, 0);
+ /* default is 'none' for delayed video mode setup */
+#endif
+#ifdef CONFIG_VIDEO_DELAY_ENABLING
+ dev_add_param(fb_dev, "enable", fb_enable_set, NULL, 0);
+ /* default is 'off' for delayed video output */
+#endif
+ return 0;
+}
+
+struct framebuffer_desc {
+ struct cdev cdev;
+ struct fb_info info;
+};
+
+static int fb_probe(struct device_d *fb_dev)
+{
+ int id = get_free_deviceid("fb");
+ struct cdev *cdev;
+ struct fb_info *info;
+ struct fb_host *host = fb_dev->platform_data;
+
+ cdev = xzalloc(sizeof(struct framebuffer_desc));
+ info = (struct fb_info*)&cdev[1];
+
+ fb_dev->priv = cdev; /* pointer forward */
+ cdev->dev = fb_dev; /* pointer backward */
+
+ cdev->ops = &fb_ops;
+ cdev->name = asprintf("fb%d", id);
+
+ cdev->size = fb_dev->size; /* use the default if any */
+ cdev->priv = info;
+
+ info->host = host;
+ info->fb_dev = fb_dev;
+
+ /* setup defaults */
+ if (host->bits_per_pixel != 0)
+ info->bits_per_pixel = host->bits_per_pixel;
+ else
+ info->bits_per_pixel = 16; /* means RGB565 */
+
+ /* add params on demand */
+ add_fb_parameter(fb_dev);
+
+ devfs_create(cdev);
+#ifndef CONFIG_VIDEO_DELAY_INIT
+ /* initialize video mode immediately (the first one) */
+ fb_activate_mode(fb_dev, &host->mode[0]);
+#endif
+#ifndef CONFIG_VIDEO_DELAY_ENABLING
+ /* enable video output immediately */
+ (host->fb_enable)(info);
+#endif
+ return 0;
+}
+
+static struct driver_d fb_driver = {
+ .name = "framebuffer",
+ .probe = fb_probe,
+};
+
+static int framebuffer_init(void)
+{
+ return register_driver(&fb_driver);
+}
+
+device_initcall(framebuffer_init);
+
+struct device_d *register_framebuffer(struct fb_host *host, void *base, unsigned size)
+{
+ struct device_d *fb_dev;
+ int rc;
+
+ fb_dev = xzalloc(sizeof(struct device_d));
+
+ strcpy(fb_dev->name, fb_driver.name);
+ fb_dev->platform_data = (void*)host;
+
+ /* setup the defaults for this framebuffer if given */
+ fb_dev->size = size;
+ fb_dev->map_base = (unsigned long)base;
+
+ rc = register_device(fb_dev);
+ if (rc != 0) {
+ pr_debug("Cannot register framebuffer device\n");
+ free(fb_dev);
+ return NULL;
+ }
+
+ return fb_dev;
+}
+#endif
+
int register_framebuffer(struct fb_info *info)
{
int id = get_free_deviceid("fb");
diff --git a/include/fb.h b/include/fb.h
index 218b244..96edc24 100644
--- a/include/fb.h
+++ b/include/fb.h
@@ -85,6 +85,46 @@ struct fb_ops {
void (*fb_disable)(struct fb_info *info);
};
+#if 0
+struct fb_host {
+ const struct fb_videomode *mode;
+ unsigned mode_cnt;
+
+ struct device_d *hw_dev;
+
+ /* callbacks into the video hardware driver */
+ int (*fb_setcolreg)(struct fb_info*, unsigned, unsigned, unsigned, unsigned, unsigned);
+ int (*fb_mode)(struct fb_info*, const struct fb_videomode*);
+ void (*fb_enable)(struct fb_info*);
+ void (*fb_disable)(struct fb_info*);
+
+ unsigned bits_per_pixel;
+};
+
+struct fb_info {
+ struct fb_host *host;
+ struct device_d *fb_dev;
+ const struct fb_videomode *active_mode;
+
+ u32 xres; /* visible resolution */
+ u32 yres;
+ u32 bits_per_pixel; /* guess what */
+
+ u32 grayscale; /* != 0 Graylevels instead of colors */
+
+ struct fb_bitfield red; /* bitfield in fb mem if true color, */
+ struct fb_bitfield green; /* else only length is significant */
+ struct fb_bitfield blue;
+ struct fb_bitfield transp; /* transparency */
+
+#ifdef CONFIG_VIDEO_DELAY_ENABLING
+ int enabled;
+#endif
+};
+
+struct device_d *register_framebuffer(struct fb_host*, void*, unsigned);
+#endif
+
struct fb_info {
struct fb_videomode *mode;
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 03/11] Bring in dynamic videomode selection at runtime
2010-10-22 16:53 ` [PATCH 03/11] Bring in dynamic videomode selection at runtime Juergen Beisert
@ 2010-10-22 17:41 ` Sascha Hauer
2010-10-23 10:35 ` Juergen Beisert
0 siblings, 1 reply; 23+ messages in thread
From: Sascha Hauer @ 2010-10-22 17:41 UTC (permalink / raw)
To: Juergen Beisert; +Cc: barebox
On Fri, Oct 22, 2010 at 06:53:17PM +0200, Juergen Beisert wrote:
> This patch mostly rewrites all parts of /drivers/video/fb.c. As it changes
> the API to the drivers, it must be done in one step to keep the repository
> bisectable. But to do it in one step makes the patches itself unreadable.
>
> So, I decided to do it in a few steps, only for the review. All patches marked
> with a "step n of m" should be merged, prior the final commit into the
> repository.
>
> This step brings in the required functions for dynamic videomode selection at
> runtime, but keep the old functions untouched (the new ones are commented out).
>
> This is patch 1 of 7 to keep the repository bisectable.
>
> Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
> ---
> drivers/video/Kconfig | 23 +++++
> drivers/video/fb.c | 251 +++++++++++++++++++++++++++++++++++++++++++++++++
> include/fb.h | 40 ++++++++
> 3 files changed, 314 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 7a89a3f..e6ecfc8 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -5,6 +5,29 @@ menuconfig VIDEO
>
> if VIDEO
>
> +comment "runtime options"
> +
> +config VIDEO_DELAY_ENABLING
> + bool "Delayed enabling"
> + help
> + Say 'y' here to delay enabling video output. This is useful to first
> + fill the framebuffer (splash screen for example) prior enabling the
> + video device.
> + This entry adds the "enable" parameter to the video device, to enable
> + or disable video output at runtime.
> +
> +config VIDEO_DELAY_INIT
> + bool "Delayed initialization"
> + select VIDEO_DELAY_ENABLING
> + help
> + If the platform supports more than one video mode say 'y' her to delay
> + the initialization of the video device until any kind of barebox's
> + shell code sets up the correct mode at runtime.
> + This entry adds the "mode" parameter to the video device, to setup
> + the desired videomode prior enabling it at runtime.
I think the framebuffers should *never* be activated by the setup code
and should be explicitely initialized by doing a 'fb0.enable=1' on the
command line. This way we have the most flexibility. We can enable
the framebuffer when we actually need it, we can draw a splash screen
before enabling it so that we do not have a black screen before we draw
an image. Also, the environment can decide to leave the framebuffer
disabled because the kernel will draw another screen a second later. If
necessary, the environemt can do a fb0.display="sharp-whatever" before
activating it. And we do not need any kconfig options for this.
Sascha
> +
> +comment "drivers"
> +
> config DRIVER_VIDEO_IMX
> bool "i.MX framebuffer driver"
> depends on ARCH_IMX1 || ARCH_IMX21 || ARCH_IMX25 || ARCH_IMX27
> diff --git a/drivers/video/fb.c b/drivers/video/fb.c
> index f9a425e..c2934f6 100644
> --- a/drivers/video/fb.c
> +++ b/drivers/video/fb.c
> @@ -1,3 +1,4 @@
> +#include <init.h>
> #include <common.h>
> #include <fb.h>
> #include <errno.h>
> @@ -5,6 +6,8 @@
> #include <getopt.h>
> #include <fcntl.h>
> #include <fs.h>
> +#include <malloc.h>
> +#include <xfuncs.h>
>
> static int fb_ioctl(struct cdev* cdev, int req, void *data)
> {
> @@ -57,6 +60,141 @@ static int fb_enable_set(struct device_d *dev, struct param_d *param,
> return 0;
> }
>
> +#if 0
> +#ifdef CONFIG_VIDEO_DELAY_INIT
> +static int fb_check_if_already_initialized(struct device_d *fb_dev)
> +{
> + struct cdev *cdev = fb_dev->priv;
> + struct fb_info *info = cdev->priv;
> +
> + if (info->active_mode != NULL) {
> + pr_err("Video mode '%s' is already set. Cannot change colour depth anymore.\n", info->active_mode->name);
> + return -EPERM;
> + }
> +
> + return 0;
> +}
> +
> +static int fb_cdepth_set(struct device_d *fb_dev, struct param_d *param, const char *val)
> +{
> + struct cdev *cdev = fb_dev->priv;
> + struct fb_info *info = cdev->priv;
> + unsigned cdepth;
> + int rc;
> +
> + rc = fb_check_if_already_initialized(fb_dev);
> + if (rc != 0)
> + return rc;
> +
> + cdepth = simple_strtoul(val, NULL, 0);
> + if (cdepth != 0)
> + info->bits_per_pixel = cdepth;
> + else
> + return -EINVAL;
> +
> + return dev_param_set_generic(fb_dev, param, val);
> +}
> +#endif
> +
> +#ifdef CONFIG_VIDEO_DELAY_ENABLING
> +static int fb_enable_set(struct device_d *fb_dev, struct param_d *param, const char *val)
> +{
> + struct cdev *cdev = fb_dev->priv;
> + struct fb_info *info = cdev->priv;
> + struct fb_host *host = fb_dev->platform_data;
> + int enable;
> + char *new;
> +
> + if (!val)
> + return dev_param_set_generic(fb_dev, param, NULL);
> +
> + enable = simple_strtoul(val, NULL, 0);
> +
> + if (info->enabled == !!enable)
> + return 0;
> +
> + if (enable) {
> + (host->fb_enable)(info);
> + new = "1";
> + } else {
> + (host->fb_disable)(info);
> + new = "0";
> + }
> +
> + info->enabled = !!enable;
> +
> + return dev_param_set_generic(fb_dev, param, new);
> +}
> +#endif
> +
> +static void fb_list_modes(struct fb_host *host)
> +{
> + unsigned u;
> +
> + if (host->mode_cnt == 0)
> + return;
> +
> + printf(" Supported video mode(s):\n");
> + for (u = 0; u < host->mode_cnt; u++)
> + printf(" '%s'\n", host->mode[u].name);
> +}
> +
> +static int fb_activate_mode(struct device_d *fb_dev, const struct fb_videomode *mode)
> +{
> + struct cdev *cdev = fb_dev->priv;
> + struct fb_info *info = cdev->priv;
> + struct fb_host *host = fb_dev->platform_data;
> + int rc;
> +
> + rc = (host->fb_mode)(info, mode);
> + if (rc != 0)
> + return rc;
> +
> + info->active_mode = mode;
> + /*
> + * At this point of time we know the remaining information we need
> + * for the cdev and fb_info structure.
> + */
> + cdev->size = fb_dev->size;
> + info->xres = mode->xres;
> + info->yres = mode->yres;
> +
> + return 0;
> +}
> +
> +#ifdef CONFIG_VIDEO_DELAY_INIT
> +static int fb_mode_set(struct device_d *fb_dev, struct param_d *param, const char *name)
> +{
> + struct fb_host *host = fb_dev->platform_data;
> + unsigned u;
> + int rc;
> +
> + pr_debug("%s called\n", __func__);
> +
> + rc = fb_check_if_already_initialized(fb_dev);
> + if (rc != 0)
> + return rc;
> +
> + /* Search for the requested video mode by name */
> + for (u = 0; u < host->mode_cnt; u++) {
> + if (!strcmp(host->mode[u].name, name))
> + break;
> + }
> + if (u >= host->mode_cnt) {
> + fb_list_modes(host); /* no mode with 'name' found */
> + return -ENODEV;
> + } else {
> + rc = fb_activate_mode(fb_dev, &host->mode[u]);
> + }
> +
> + if (rc == 0)
> + dev_param_set_generic(fb_dev, param, name);
> +
> + return rc;
> +}
> +#endif
> +#endif
> +
> static struct file_operations fb_ops = {
> .read = mem_read,
> .write = mem_write,
> @@ -65,6 +203,119 @@ static struct file_operations fb_ops = {
> .ioctl = fb_ioctl,
> };
>
> +#if 0
> +static int add_fb_parameter(struct device_d *fb_dev)
> +{
> +#ifdef CONFIG_VIDEO_DELAY_INIT
> + struct cdev *cdev = fb_dev->priv;
> + struct fb_info *info = cdev->priv;
> + char cd[10];
> +
> + /** @todo provide base address parameter for the user */
> +
> + dev_add_param(fb_dev, "cdepth", fb_cdepth_set, NULL, 0);
> + if (info->bits_per_pixel == 0) {
> + dev_set_param(fb_dev, "cdepth", "16");
> + info->bits_per_pixel = 16;
> + } else {
> + sprintf(cd, "%u", info->bits_per_pixel);
> + dev_set_param(fb_dev, "cdepth", cd);
> + }
> + dev_add_param(fb_dev, "mode", fb_mode_set, NULL, 0);
> + /* default is 'none' for delayed video mode setup */
> +#endif
> +#ifdef CONFIG_VIDEO_DELAY_ENABLING
> + dev_add_param(fb_dev, "enable", fb_enable_set, NULL, 0);
> + /* default is 'off' for delayed video output */
> +#endif
> + return 0;
> +}
> +
> +struct framebuffer_desc {
> + struct cdev cdev;
> + struct fb_info info;
> +};
> +
> +static int fb_probe(struct device_d *fb_dev)
> +{
> + int id = get_free_deviceid("fb");
> + struct cdev *cdev;
> + struct fb_info *info;
> + struct fb_host *host = fb_dev->platform_data;
> +
> + cdev = xzalloc(sizeof(struct framebuffer_desc));
> + info = (struct fb_info*)&cdev[1];
> +
> + fb_dev->priv = cdev; /* pointer forward */
> + cdev->dev = fb_dev; /* pointer backward */
> +
> + cdev->ops = &fb_ops;
> + cdev->name = asprintf("fb%d", id);
> +
> + cdev->size = fb_dev->size; /* use the default if any */
> + cdev->priv = info;
> +
> + info->host = host;
> + info->fb_dev = fb_dev;
> +
> + /* setup defaults */
> + if (host->bits_per_pixel != 0)
> + info->bits_per_pixel = host->bits_per_pixel;
> + else
> + info->bits_per_pixel = 16; /* means RGB565 */
> +
> + /* add params on demand */
> + add_fb_parameter(fb_dev);
> +
> + devfs_create(cdev);
> +#ifndef CONFIG_VIDEO_DELAY_INIT
> + /* initialize video mode immediately (the first one) */
> + fb_activate_mode(fb_dev, &host->mode[0]);
> +#endif
> +#ifndef CONFIG_VIDEO_DELAY_ENABLING
> + /* enable video output immediately */
> + (host->fb_enable)(info);
> +#endif
> + return 0;
> +}
> +
> +static struct driver_d fb_driver = {
> + .name = "framebuffer",
> + .probe = fb_probe,
> +};
> +
> +static int framebuffer_init(void)
> +{
> + return register_driver(&fb_driver);
> +}
> +
> +device_initcall(framebuffer_init);
> +
> +struct device_d *register_framebuffer(struct fb_host *host, void *base, unsigned size)
> +{
> + struct device_d *fb_dev;
> + int rc;
> +
> + fb_dev = xzalloc(sizeof(struct device_d));
> +
> + strcpy(fb_dev->name, fb_driver.name);
> + fb_dev->platform_data = (void*)host;
> +
> + /* setup the defaults for this framebuffer if given */
> + fb_dev->size = size;
> + fb_dev->map_base = (unsigned long)base;
> +
> + rc = register_device(fb_dev);
> + if (rc != 0) {
> + pr_debug("Cannot register framebuffer device\n");
> + free(fb_dev);
> + return NULL;
> + }
> +
> + return fb_dev;
> +}
> +#endif
> +
> int register_framebuffer(struct fb_info *info)
> {
> int id = get_free_deviceid("fb");
> diff --git a/include/fb.h b/include/fb.h
> index 218b244..96edc24 100644
> --- a/include/fb.h
> +++ b/include/fb.h
> @@ -85,6 +85,46 @@ struct fb_ops {
> void (*fb_disable)(struct fb_info *info);
> };
>
> +#if 0
> +struct fb_host {
> + const struct fb_videomode *mode;
> + unsigned mode_cnt;
> +
> + struct device_d *hw_dev;
> +
> + /* callbacks into the video hardware driver */
> + int (*fb_setcolreg)(struct fb_info*, unsigned, unsigned, unsigned, unsigned, unsigned);
> + int (*fb_mode)(struct fb_info*, const struct fb_videomode*);
> + void (*fb_enable)(struct fb_info*);
> + void (*fb_disable)(struct fb_info*);
> +
> + unsigned bits_per_pixel;
> +};
> +
> +struct fb_info {
> + struct fb_host *host;
> + struct device_d *fb_dev;
> + const struct fb_videomode *active_mode;
> +
> + u32 xres; /* visible resolution */
> + u32 yres;
> + u32 bits_per_pixel; /* guess what */
> +
> + u32 grayscale; /* != 0 Graylevels instead of colors */
> +
> + struct fb_bitfield red; /* bitfield in fb mem if true color, */
> + struct fb_bitfield green; /* else only length is significant */
> + struct fb_bitfield blue;
> + struct fb_bitfield transp; /* transparency */
> +
> +#ifdef CONFIG_VIDEO_DELAY_ENABLING
> + int enabled;
> +#endif
> +};
> +
> +struct device_d *register_framebuffer(struct fb_host*, void*, unsigned);
> +#endif
> +
> struct fb_info {
> struct fb_videomode *mode;
>
> --
> 1.7.2.3
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 03/11] Bring in dynamic videomode selection at runtime
2010-10-22 17:41 ` Sascha Hauer
@ 2010-10-23 10:35 ` Juergen Beisert
0 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-23 10:35 UTC (permalink / raw)
To: barebox
Sascha Hauer wrote:
> On Fri, Oct 22, 2010 at 06:53:17PM +0200, Juergen Beisert wrote:
> > This patch mostly rewrites all parts of /drivers/video/fb.c. As it
> > changes the API to the drivers, it must be done in one step to keep the
> > repository bisectable. But to do it in one step makes the patches itself
> > unreadable.
> >
> > So, I decided to do it in a few steps, only for the review. All patches
> > marked with a "step n of m" should be merged, prior the final commit into
> > the repository.
> >
> > This step brings in the required functions for dynamic videomode
> > selection at runtime, but keep the old functions untouched (the new ones
> > are commented out).
> >
> > This is patch 1 of 7 to keep the repository bisectable.
> >
> > Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
> > ---
> > drivers/video/Kconfig | 23 +++++
> > drivers/video/fb.c | 251
> > +++++++++++++++++++++++++++++++++++++++++++++++++ include/fb.h |
> > 40 ++++++++
> > 3 files changed, 314 insertions(+), 0 deletions(-)
> >
> > diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> > index 7a89a3f..e6ecfc8 100644
> > --- a/drivers/video/Kconfig
> > +++ b/drivers/video/Kconfig
> > @@ -5,6 +5,29 @@ menuconfig VIDEO
> >
> > if VIDEO
> >
> > +comment "runtime options"
> > +
> > +config VIDEO_DELAY_ENABLING
> > + bool "Delayed enabling"
> > + help
> > + Say 'y' here to delay enabling video output. This is useful to first
> > + fill the framebuffer (splash screen for example) prior enabling the
> > + video device.
> > + This entry adds the "enable" parameter to the video device, to
> > enable + or disable video output at runtime.
> > +
> > +config VIDEO_DELAY_INIT
> > + bool "Delayed initialization"
> > + select VIDEO_DELAY_ENABLING
> > + help
> > + If the platform supports more than one video mode say 'y' her to
> > delay + the initialization of the video device until any kind of
> > barebox's + shell code sets up the correct mode at runtime.
> > + This entry adds the "mode" parameter to the video device, to
> > setup + the desired videomode prior enabling it at runtime.
>
> I think the framebuffers should *never* be activated by the setup code
> and should be explicitely initialized by doing a 'fb0.enable=1' on the
> command line.
Okay. It "should not" is a new policy to barebox. Currently the framebuffer is
activated immediately (except the platforms you changed already). I just
wanted to keep this behaviour.
> This way we have the most flexibility. We can enable
> the framebuffer when we actually need it, we can draw a splash screen
> before enabling it so that we do not have a black screen before we draw
> an image. Also, the environment can decide to leave the framebuffer
> disabled because the kernel will draw another screen a second later. If
> necessary, the environemt can do a fb0.display="sharp-whatever" before
> activating it. And we do not need any kconfig options for this.
Okay. We can change the default behaviour for all platforms using graphic in
this way. I will try to include it in the next series.
jbe
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | Phone: +49-8766-939 228 |
Vertretung Sued/Muenchen, Germany | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de/ |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 04/11] Remove the old videomode functions
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
` (2 preceding siblings ...)
2010-10-22 16:53 ` [PATCH 03/11] Bring in dynamic videomode selection at runtime Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 16:53 ` [PATCH 05/11] Add verbose framebuffer device info Juergen Beisert
` (6 subsequent siblings)
10 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
Remove the old functions from the framebuffer framework and change API for
existing functions.
This patch is kept separately for review only. Should be merged with the other
special marked patches.
This is patch 2 of 7 to keep the repository bisectable.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
drivers/video/fb.c | 67 ++-------------------------------------------------
include/fb.h | 38 -----------------------------
2 files changed, 3 insertions(+), 102 deletions(-)
diff --git a/drivers/video/fb.c b/drivers/video/fb.c
index c2934f6..ca3a4cd 100644
--- a/drivers/video/fb.c
+++ b/drivers/video/fb.c
@@ -11,6 +11,7 @@
static int fb_ioctl(struct cdev* cdev, int req, void *data)
{
+ struct fb_host *host = cdev->dev->platform_data;
struct fb_info *info = cdev->priv;
switch (req) {
@@ -18,10 +19,10 @@ static int fb_ioctl(struct cdev* cdev, int req, void *data)
memcpy(data, info, sizeof(*info));
break;
case FBIO_ENABLE:
- info->fbops->fb_enable(info);
+ (host->fb_enable)(cdev->priv);
break;
case FBIO_DISABLE:
- info->fbops->fb_disable(info);
+ (host->fb_disable)(cdev->priv);
break;
default:
return -ENOSYS;
@@ -30,37 +31,6 @@ static int fb_ioctl(struct cdev* cdev, int req, void *data)
return 0;
}
-static int fb_enable_set(struct device_d *dev, struct param_d *param,
- const char *val)
-{
- struct fb_info *info = dev->priv;
- int enable;
- char *new;
-
- if (!val)
- return dev_param_set_generic(dev, param, NULL);
-
- enable = simple_strtoul(val, NULL, 0);
-
- if (info->enabled == !!enable)
- return 0;
-
- if (enable) {
- info->fbops->fb_enable(info);
- new = "1";
- } else {
- info->fbops->fb_disable(info);
- new = "0";
- }
-
- dev_param_set_generic(dev, param, new);
-
- info->enabled = !!enable;
-
- return 0;
-}
-
-#if 0
#ifdef CONFIG_VIDEO_DELAY_INIT
static int fb_check_if_already_initialized(struct device_d *fb_dev)
{
@@ -193,7 +163,6 @@ static int fb_mode_set(struct device_d *fb_dev, struct param_d *param, const cha
return rc;
}
#endif
-#endif
static struct file_operations fb_ops = {
.read = mem_read,
@@ -203,7 +172,6 @@ static struct file_operations fb_ops = {
.ioctl = fb_ioctl,
};
-#if 0
static int add_fb_parameter(struct device_d *fb_dev)
{
#ifdef CONFIG_VIDEO_DELAY_INIT
@@ -314,32 +282,3 @@ struct device_d *register_framebuffer(struct fb_host *host, void *base, unsigned
return fb_dev;
}
-#endif
-
-int register_framebuffer(struct fb_info *info)
-{
- int id = get_free_deviceid("fb");
- struct device_d *dev;
-
- info->cdev.ops = &fb_ops;
- info->cdev.name = asprintf("fb%d", id);
- info->cdev.size = info->xres * info->yres * (info->bits_per_pixel >> 3);
- info->cdev.dev = &info->dev;
- info->cdev.priv = info;
- info->cdev.dev->map_base = (unsigned long)info->screen_base;
- info->cdev.dev->size = info->cdev.size;
-
- dev = &info->dev;
- dev->priv = info;
-
- sprintf(dev->name, "fb");
-
- register_device(&info->dev);
- dev_add_param(dev, "enable", fb_enable_set, NULL, 0);
- dev_set_param(dev, "enable", "0");
-
- devfs_create(&info->cdev);
-
- return 0;
-}
-
diff --git a/include/fb.h b/include/fb.h
index 96edc24..c004a56 100644
--- a/include/fb.h
+++ b/include/fb.h
@@ -77,15 +77,6 @@ struct fb_bitfield {
struct fb_info;
-struct fb_ops {
- /* set color register */
- int (*fb_setcolreg)(unsigned regno, unsigned red, unsigned green,
- unsigned blue, unsigned transp, struct fb_info *info);
- void (*fb_enable)(struct fb_info *info);
- void (*fb_disable)(struct fb_info *info);
-};
-
-#if 0
struct fb_host {
const struct fb_videomode *mode;
unsigned mode_cnt;
@@ -123,35 +114,6 @@ struct fb_info {
};
struct device_d *register_framebuffer(struct fb_host*, void*, unsigned);
-#endif
-
-struct fb_info {
- struct fb_videomode *mode;
-
- struct fb_ops *fbops;
- struct device_d dev; /* This is this fb device */
-
- void *screen_base;
-
- void *priv;
-
- struct cdev cdev;
-
- u32 xres; /* visible resolution */
- u32 yres;
- u32 bits_per_pixel; /* guess what */
-
- u32 grayscale; /* != 0 Graylevels instead of colors */
-
- struct fb_bitfield red; /* bitfield in fb mem if true color, */
- struct fb_bitfield green; /* else only length is significant */
- struct fb_bitfield blue;
- struct fb_bitfield transp; /* transparency */
-
- int enabled;
-};
-
-int register_framebuffer(struct fb_info *info);
#define FBIOGET_SCREENINFO _IOR('F', 1, loff_t)
#define FBIO_ENABLE _IO('F', 2)
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* [PATCH 05/11] Add verbose framebuffer device info
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
` (3 preceding siblings ...)
2010-10-22 16:53 ` [PATCH 04/11] Remove the old videomode functions Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 16:53 ` [PATCH 06/11] Adapt the existing imx fb driver to support runtime videomode selection Juergen Beisert
` (5 subsequent siblings)
10 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
This is patch 3 of 7 to keep the repository bisectable.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
drivers/video/Kconfig | 6 ++++++
drivers/video/fb.c | 40 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 46 insertions(+), 0 deletions(-)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index e6ecfc8..f96accc 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -26,6 +26,12 @@ config VIDEO_DELAY_INIT
This entry adds the "mode" parameter to the video device, to setup
the desired videomode prior enabling it at runtime.
+config VIDEO_INFO_VERBOSE
+ bool "verbose video info"
+ help
+ Say 'y' here to be more verbose when running the 'devinfo' command
+ on the framebuffer device.
+
comment "drivers"
config DRIVER_VIDEO_IMX
diff --git a/drivers/video/fb.c b/drivers/video/fb.c
index ca3a4cd..15d993d 100644
--- a/drivers/video/fb.c
+++ b/drivers/video/fb.c
@@ -172,6 +172,45 @@ static struct file_operations fb_ops = {
.ioctl = fb_ioctl,
};
+static void fb_info(struct device_d *fb_dev)
+{
+ struct cdev *cdev = fb_dev->priv;
+ struct fb_info *info = cdev->priv;
+
+ printf(" Video/Mode info:\n");
+#ifdef CONFIG_VIDEO_DELAY_ENABLING
+ printf(" Video output %senabled\n", info->enabled != 0 ? "" : "not ");
+#endif
+ printf(" Current video mode:\n");
+ if (info->active_mode != NULL) {
+ printf(" Name: %s\n", info->active_mode->name);
+#ifdef CONFIG_VIDEO_INFO_VERBOSE
+ if (info->active_mode->refresh == 0)
+ printf(" Refresh rate: undefined\n");
+ else
+ printf(" Refresh rate: %u Hz\n", info->active_mode->refresh);
+ printf(" Horizontal active pixel: %u\n", info->active_mode->xres);
+ printf(" Vertical active lines: %u\n", info->active_mode->yres);
+ printf(" Pixel clock: %u kHz\n", PICOS2KHZ(info->active_mode->pixclock));
+ printf(" Left/Right margin (pixel): %u/%u\n", info->active_mode->left_margin,
+ info->active_mode->right_margin);
+ printf(" Upper/Lower margin (lines): %u/%u\n", info->active_mode->upper_margin,
+ info->active_mode->lower_margin);
+ printf(" HSYNC length in pixel: %u, polarity: %s\n", info->active_mode->hsync_len,
+ (info->active_mode->sync & FB_SYNC_HOR_HIGH_ACT) ? "high" : "low");
+ printf(" VSYNC length in lines: %u, polarity: %s\n", info->active_mode->vsync_len,
+ (info->active_mode->sync & FB_SYNC_VERT_HIGH_ACT) ? "high" : "low");
+ printf(" Colour depth: %u bpp\n", info->bits_per_pixel);
+ printf(" Framebuffer size is: %u bytes\n", cdev->size);
+ /* TODO add the remaining information from fb_videomode. How valuable are they? */
+#endif
+ } else {
+ printf (" No video mode selected yet\n");
+ }
+
+ fb_list_modes(fb_dev->platform_data);
+}
+
static int add_fb_parameter(struct device_d *fb_dev)
{
#ifdef CONFIG_VIDEO_DELAY_INIT
@@ -250,6 +289,7 @@ static int fb_probe(struct device_d *fb_dev)
static struct driver_d fb_driver = {
.name = "framebuffer",
.probe = fb_probe,
+ .info = fb_info,
};
static int framebuffer_init(void)
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* [PATCH 06/11] Adapt the existing imx fb driver to support runtime videomode selection
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
` (4 preceding siblings ...)
2010-10-22 16:53 ` [PATCH 05/11] Add verbose framebuffer device info Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 16:53 ` [PATCH 07/11] Adapt the existing imx-ipu " Juergen Beisert
` (4 subsequent siblings)
10 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
Adapt the API to the new framebuffer videomode selection at runtime. If the new
feature is not used, there is no visible change at runtime for platforms using
this driver.
NOTE: Due to the lack of hardware, this is compile time tested only.
This is patch 4 of 7 to keep the repository bisectable.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
arch/arm/mach-imx/include/mach/imxfb.h | 1 +
drivers/video/imx.c | 211 ++++++++++++++++++--------------
2 files changed, 120 insertions(+), 92 deletions(-)
diff --git a/arch/arm/mach-imx/include/mach/imxfb.h b/arch/arm/mach-imx/include/mach/imxfb.h
index 7baa244..c536119 100644
--- a/arch/arm/mach-imx/include/mach/imxfb.h
+++ b/arch/arm/mach-imx/include/mach/imxfb.h
@@ -60,6 +60,7 @@ struct imx_fb_videomode {
*/
struct imx_fb_platform_data {
struct imx_fb_videomode *mode;
+ unsigned mode_cnt; /**< number of entries in 'mode' */
u_int cmap_greyscale:1,
cmap_inverse:1,
diff --git a/drivers/video/imx.c b/drivers/video/imx.c
index 6ccd77e..07438e5 100644
--- a/drivers/video/imx.c
+++ b/drivers/video/imx.c
@@ -137,6 +137,7 @@ struct imxfb_rgb {
};
struct imxfb_info {
+ struct fb_host fb_host; /**< myself */
void __iomem *regs;
u_int pcr;
@@ -147,16 +148,15 @@ struct imxfb_info {
cmap_static:1,
unused:30;
- struct imx_fb_videomode *mode;
-
- struct fb_info info;
- struct device_d *dev;
-
void (*enable)(int enable);
- struct fb_info overlay;
+ struct fb_host fb_overlay;
};
+#define fb_overlay_to_imxfb_info(x) (container_of((struct fb_host*)(x->host), struct imxfb_info, fb_overlay))
+#define fb_overlay_dev_to_imxfb_info(x) (container_of((struct fb_host*)(x->platform_data), struct imxfb_info, fb_overlay))
+#define fb_info_to_imxfb_info(x) ((struct imxfb_info*)((x)->host))
+
#define IMX_NAME "IMX"
/*
@@ -204,11 +204,10 @@ static inline u_int chan_to_field(u_int chan, struct fb_bitfield *bf)
return chan << bf->offset;
}
-
-static int imxfb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
- u_int trans, struct fb_info *info)
+static int imxfb_setcolreg(struct fb_info *info, u_int regno, u_int red,
+ u_int green, u_int blue, u_int trans)
{
- struct imxfb_info *fbi = info->priv;
+ struct imxfb_info *fbi = fb_info_to_imxfb_info(info);
int ret = 1;
u32 val;
@@ -247,7 +246,7 @@ static int imxfb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
static void imxfb_enable_controller(struct fb_info *info)
{
- struct imxfb_info *fbi = info->priv;
+ struct imxfb_info *fbi = fb_info_to_imxfb_info(info);
writel(RMCR_LCDC_EN, fbi->regs + LCDC_RMCR);
#ifdef CONFIG_ARCH_IMX21
@@ -269,7 +268,7 @@ static void imxfb_enable_controller(struct fb_info *info)
static void imxfb_disable_controller(struct fb_info *info)
{
- struct imxfb_info *fbi = info->priv;
+ struct imxfb_info *fbi = fb_info_to_imxfb_info(info);
if (fbi->enable)
fbi->enable(0);
@@ -295,14 +294,35 @@ static void imxfb_disable_controller(struct fb_info *info)
* Configures LCD Controller based on entries in var parameter. Settings are
* only written to the controller if changes were made.
*/
-static int imxfb_activate_var(struct fb_info *info)
+static int imxfb_initialize_mode(struct fb_info *info, const struct fb_videomode *mode)
{
- struct fb_videomode *mode = info->mode;
struct imxfb_rgb *rgb;
unsigned long lcd_clk;
unsigned long long tmp;
- struct imxfb_info *fbi = info->priv;
+ struct imxfb_info *fbi = fb_info_to_imxfb_info(info);
u32 pcr;
+ unsigned size;
+
+ /*
+ * we need at least this amount of memory for the framebuffer
+ */
+ size = mode->xres * mode->yres * (info->bits_per_pixel >> 3);
+ if (info->fb_dev->size != 0) {
+ if (size > info->fb_dev->size) {
+ pr_err("Cannot initialize video mode '%s': Its too large. "
+ "Required bytes are %u, available only %u\n",
+ mode->name, size, info->fb_dev->size);
+ return -EINVAL;
+ }
+ } else
+ info->fb_dev->size = size;
+
+ /*
+ * if no framebuffer memory was specified yet, allocate one,
+ * and allocate more memory, on user request
+ */
+ if (info->fb_dev->map_base == 0U /* FIXME should be 'NULL'*/)
+ info->fb_dev->map_base = (unsigned long)xzalloc(info->fb_dev->size);
/* physical screen start address */
writel(VPW_VPW(mode->xres * info->bits_per_pixel / 8 / 4),
@@ -318,13 +338,13 @@ static int imxfb_activate_var(struct fb_info *info)
VCR_V_WAIT_2(mode->upper_margin),
fbi->regs + LCDC_VCR);
- writel(SIZE_XMAX(info->xres) | SIZE_YMAX(info->yres),
+ writel(SIZE_XMAX(mode->xres) | SIZE_YMAX(mode->yres),
fbi->regs + LCDC_SIZE);
writel(fbi->pwmr, fbi->regs + LCDC_PWMR);
writel(fbi->lscr1, fbi->regs + LCDC_LSCR1);
writel(fbi->dmacr, fbi->regs + LCDC_DMACR);
- writel((unsigned long)fbi->info.screen_base, fbi->regs + LCDC_SSA);
+ writel((uint32_t)info->fb_dev->map_base, fbi->regs + LCDC_SSA);
/* panning offset 0 (0 pixel offset) */
writel(0x0, fbi->regs + LCDC_POS);
@@ -386,16 +406,10 @@ static int imxfb_activate_var(struct fb_info *info)
return 0;
}
-static struct fb_ops imxfb_ops = {
- .fb_setcolreg = imxfb_setcolreg,
- .fb_enable = imxfb_enable_controller,
- .fb_disable = imxfb_disable_controller,
-};
-
#ifdef CONFIG_IMXFB_DRIVER_VIDEO_IMX_OVERLAY
static void imxfb_overlay_enable_controller(struct fb_info *overlay)
{
- struct imxfb_info *fbi = overlay->priv;
+ struct imxfb_info *fbi = fb_overlay_to_imxfb_info(overlay);
unsigned int tmp;
tmp = readl(fbi->regs + LCDC_LGWCR);
@@ -405,7 +419,7 @@ static void imxfb_overlay_enable_controller(struct fb_info *overlay)
static void imxfb_overlay_disable_controller(struct fb_info *overlay)
{
- struct imxfb_info *fbi = overlay->priv;
+ struct imxfb_info *fbi = fb_overlay_to_imxfb_info(overlay);
unsigned int tmp;
tmp = readl(fbi->regs + LCDC_LGWCR);
@@ -413,23 +427,16 @@ static void imxfb_overlay_disable_controller(struct fb_info *overlay)
writel(tmp , fbi->regs + LCDC_LGWCR);
}
-static int imxfb_overlay_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
- u_int trans, struct fb_info *info)
+static int imxfb_overlay_setcolreg(struct fb_info *overlay, u_int regno,
+ u_int red, u_int green, u_int blue, u_int trans)
{
return 0;
}
-static struct fb_ops imxfb_overlay_ops = {
- .fb_setcolreg = imxfb_overlay_setcolreg,
- .fb_enable = imxfb_overlay_enable_controller,
- .fb_disable = imxfb_overlay_disable_controller,
-};
-
static int imxfb_alpha_set(struct device_d *dev, struct param_d *param,
const char *val)
{
- struct fb_info *overlay = dev->priv;
- struct imxfb_info *fbi = overlay->priv;
+ struct imxfb_info *fbi = fb_overlay_dev_to_imxfb_info(dev);
int alpha;
char alphastr[16];
unsigned int tmp;
@@ -452,32 +459,35 @@ static int imxfb_alpha_set(struct device_d *dev, struct param_d *param,
return 0;
}
-static int imxfb_register_overlay(struct imxfb_info *fbi, void *fb)
+static int imxfb_overlay_mode(struct fb_info *overlay, const struct fb_videomode *mode)
{
- struct fb_info *overlay;
+ struct imxfb_info *fbi = fb_overlay_to_imxfb_info(overlay);
struct imxfb_rgb *rgb;
- int ret;
-
- overlay = &fbi->overlay;
-
- overlay->priv = fbi;
- overlay->mode = fbi->info.mode;
- overlay->xres = fbi->info.xres;
- overlay->yres = fbi->info.yres;
- overlay->bits_per_pixel = fbi->info.bits_per_pixel;
- overlay->fbops = &imxfb_overlay_ops;
-
- if (fb)
- overlay->screen_base = fb;
- else
- overlay->screen_base = xzalloc(overlay->xres * overlay->yres *
- (overlay->bits_per_pixel >> 3));
-
- writel((unsigned long)overlay->screen_base, fbi->regs + LCDC_LGWSAR);
- writel(SIZE_XMAX(overlay->xres) | SIZE_YMAX(overlay->yres),
- fbi->regs + LCDC_LGWSR);
- writel(VPW_VPW(overlay->xres * overlay->bits_per_pixel / 8 / 4),
- fbi->regs + LCDC_LGWVPWR);
+ unsigned size;
+
+ /* we need at least this amount of memory for the framebuffer */
+ size = mode->xres * mode->yres * (overlay->bits_per_pixel >> 3);
+
+ if (overlay->fb_dev->size != 0) {
+ if (size > overlay->fb_dev->size) {
+ pr_err("Cannot initialize video mode '%s': Its too large. "
+ "Required bytes are %u, available only %u\n",
+ mode->name, size, overlay->fb_dev->size);
+ return -EINVAL;
+ }
+ } else
+ overlay->fb_dev->size = size;
+
+ /*
+ * if no framebuffer memory was specified yet, allocate one,
+ * and allocate more memory, on user request
+ */
+ if (overlay->fb_dev->map_base == 0U /* FIXME should be 'NULL'*/)
+ overlay->fb_dev->map_base = (unsigned long)xzalloc(overlay->fb_dev->size);
+
+ writel((uint32_t)overlay->fb_dev->map_base, fbi->regs + LCDC_LGWSAR);
+ writel(SIZE_XMAX(mode->xres) | SIZE_YMAX(mode->yres), fbi->regs + LCDC_LGWSR);
+ writel(VPW_VPW(mode->xres * overlay->bits_per_pixel / 8 / 4), fbi->regs + LCDC_LGWVPWR);
writel(0, fbi->regs + LCDC_LGWPR);
writel(LGWCR_GWAV(0x0), fbi->regs + LCDC_LGWCR);
@@ -506,14 +516,36 @@ static int imxfb_register_overlay(struct imxfb_info *fbi, void *fb)
overlay->blue = rgb->blue;
overlay->transp = rgb->transp;
- ret = register_framebuffer(overlay);
- if (ret < 0) {
- dev_err(fbi->dev, "failed to register framebuffer\n");
- return ret;
+ return 0;
+}
+
+static int imxfb_register_overlay(struct imxfb_info *fbi, struct device_d *hw_dev,
+ struct imx_fb_platform_data *pdata)
+{
+ struct fb_host *overlay;
+ struct device_d *overlay_dev;
+
+ overlay = &fbi->fb_overlay;
+
+ /* add runtime hardware info */
+ overlay->hw_dev = hw_dev; /* same as the master device */
+ overlay->fb_mode = imxfb_overlay_mode;
+ overlay->fb_enable = imxfb_overlay_enable_controller;
+ overlay->fb_disable = imxfb_overlay_disable_controller;
+ overlay->fb_setcolreg = imxfb_overlay_setcolreg;
+
+ /* add runtime video info */
+ overlay->mode = pdata->mode->mode;
+ overlay->mode_cnt = 1; /* no choice */
+
+ overlay_dev = register_framebuffer(overlay, pdata->framebuffer_ovl, 0);
+ if (overlay_dev == NULL) {
+ dev_err(hw_dev, "failed to register overlay framebuffer\n");
+ return -EINVAL;
}
- dev_add_param(&overlay->dev, "alpha", imxfb_alpha_set, NULL, 0);
- dev_set_param(&overlay->dev, "alpha", "0");
+ dev_add_param(overlay_dev, "alpha", imxfb_alpha_set, NULL, 0);
+ dev_set_param(overlay_dev, "alpha", "0");
return 0;
}
@@ -522,13 +554,13 @@ static int imxfb_register_overlay(struct imxfb_info *fbi, void *fb)
static int imxfb_probe(struct device_d *dev)
{
struct imxfb_info *fbi;
- struct fb_info *info;
+ struct device_d *fb_dev;
struct imx_fb_platform_data *pdata = dev->platform_data;
- int ret;
if (!pdata)
return -ENODEV;
+ /* TODO should be done when enabling the video output */
#ifdef CONFIG_ARCH_IMX21
PCCR0 &= ~(PCCR0_PERCLK3_EN | PCCR0_HCLK_LCDC_EN);
#endif
@@ -544,40 +576,35 @@ static int imxfb_probe(struct device_d *dev)
#endif
fbi = xzalloc(sizeof(*fbi));
- info = &fbi->info;
- fbi->mode = pdata->mode;
- fbi->regs = (void *)dev->map_base;
+ /* add runtime hardware info */
+ fbi->fb_host.hw_dev = dev;
+ fbi->fb_host.fb_mode = imxfb_initialize_mode;
+ fbi->fb_host.fb_enable = imxfb_enable_controller;
+ fbi->fb_host.fb_disable = imxfb_disable_controller;
+ fbi->fb_host.fb_setcolreg = imxfb_setcolreg;
+
+ fbi->regs = (void*)dev->map_base;
fbi->pcr = pdata->mode->pcr;
fbi->pwmr = pdata->pwmr;
fbi->lscr1 = pdata->lscr1;
fbi->dmacr = pdata->dmacr;
fbi->enable = pdata->enable;
- fbi->dev = dev;
- info->priv = fbi;
- info->mode = pdata->mode->mode;
- info->xres = pdata->mode->mode->xres;
- info->yres = pdata->mode->mode->yres;
- info->bits_per_pixel = pdata->mode->bpp;
- info->fbops = &imxfb_ops;
-
- dev_info(dev, "i.MX Framebuffer driver\n");
-
- if (pdata->framebuffer)
- fbi->info.screen_base = pdata->framebuffer;
- else
- fbi->info.screen_base = xzalloc(info->xres * info->yres *
- (info->bits_per_pixel >> 3));
-
- imxfb_activate_var(&fbi->info);
-
- ret = register_framebuffer(&fbi->info);
- if (ret < 0) {
+
+ /* add runtime video info */
+ fbi->fb_host.mode = pdata->mode->mode;
+ /* to be backward compatible */
+ fbi->fb_host.mode_cnt = pdata->mode_cnt == 0 ? 1 : pdata->mode_cnt;
+ fbi->fb_host.bits_per_pixel = 16; /* RGB565, the default */
+
+ fb_dev = register_framebuffer(&fbi->fb_host, pdata->framebuffer, 0);
+ if (dev == NULL) {
dev_err(dev, "failed to register framebuffer\n");
- return ret;
+ return -EINVAL;
}
+
#ifdef CONFIG_IMXFB_DRIVER_VIDEO_IMX_OVERLAY
- imxfb_register_overlay(fbi, pdata->framebuffer_ovl);
+ imxfb_register_overlay(fbi, fb_dev, pdata);
#endif
return 0;
}
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* [PATCH 07/11] Adapt the existing imx-ipu fb driver to support runtime videomode selection
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
` (5 preceding siblings ...)
2010-10-22 16:53 ` [PATCH 06/11] Adapt the existing imx fb driver to support runtime videomode selection Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 17:43 ` Sascha Hauer
2010-10-22 16:53 ` [PATCH 08/11] Add a video driver for S3C2440 bases platforms Juergen Beisert
` (3 subsequent siblings)
10 siblings, 1 reply; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
Adapt the API to the new framebuffer videomode selection at runtime. If the new
feature is not used, there is no visible change at runtime for platforms using
this driver.
NOTE: Due to the lack of hardware, this is compile time tested only.
This is patch 5 of 7 to keep the repository bisectable.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
arch/arm/boards/freescale-mx35-3-stack/3stack.c | 2 +-
arch/arm/boards/pcm043/pcm043.c | 2 +-
arch/arm/mach-imx/include/mach/imx-ipu-fb.h | 12 +--
drivers/video/imx-ipu-fb.c | 156 +++++++++++++---------
4 files changed, 96 insertions(+), 76 deletions(-)
diff --git a/arch/arm/boards/freescale-mx35-3-stack/3stack.c b/arch/arm/boards/freescale-mx35-3-stack/3stack.c
index d6699cd..fb40f50 100644
--- a/arch/arm/boards/freescale-mx35-3-stack/3stack.c
+++ b/arch/arm/boards/freescale-mx35-3-stack/3stack.c
@@ -139,7 +139,7 @@ static struct fb_videomode CTP_CLAA070LC0ACW = {
.lower_margin = 10, /* whole frame should have 500 lines */
.hsync_len = 1, /* note: DE only display */
.vsync_len = 1, /* note: DE only display */
- .sync = FB_SYNC_CLK_IDLE_EN | FB_SYNC_OE_ACT_HIGH,
+ .sync = FB_SYNC_CLK_IDLE_EN | FB_SYNC_DE_HIGH_ACT,
.vmode = FB_VMODE_NONINTERLACED,
.flag = 0,
};
diff --git a/arch/arm/boards/pcm043/pcm043.c b/arch/arm/boards/pcm043/pcm043.c
index 5932f95..7e63cc5 100644
--- a/arch/arm/boards/pcm043/pcm043.c
+++ b/arch/arm/boards/pcm043/pcm043.c
@@ -124,7 +124,7 @@ static struct fb_videomode pcm043_fb_mode = {
.lower_margin = 40,
.hsync_len = 96,
.vsync_len = 1,
- .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
+ .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_DE_HIGH_ACT,
.vmode = FB_VMODE_NONINTERLACED,
.flag = 0,
};
diff --git a/arch/arm/mach-imx/include/mach/imx-ipu-fb.h b/arch/arm/mach-imx/include/mach/imx-ipu-fb.h
index 8e1cc87..ce95243 100644
--- a/arch/arm/mach-imx/include/mach/imx-ipu-fb.h
+++ b/arch/arm/mach-imx/include/mach/imx-ipu-fb.h
@@ -12,20 +12,12 @@
#include <fb.h>
-/* Proprietary FB_SYNC_ flags */
-#define FB_SYNC_OE_ACT_HIGH 0x80000000
-#define FB_SYNC_CLK_INVERT 0x40000000
-#define FB_SYNC_DATA_INVERT 0x20000000
-#define FB_SYNC_CLK_IDLE_EN 0x10000000
-#define FB_SYNC_SHARP_MODE 0x08000000
-#define FB_SYNC_SWAP_RGB 0x04000000
-#define FB_SYNC_CLK_SEL_EN 0x02000000
-
/*
- * struct mx3fb_platform_data - mx3fb platform data
+ * struct imx_ipu_fb_platform_data - imx-ipu-fb's platform data
*/
struct imx_ipu_fb_platform_data {
struct fb_videomode *mode;
+ unsigned mode_cnt; /**< number of entries in 'mode' */
unsigned char bpp;
void __iomem *framebuffer;
/** hook to enable backlight and stuff */
diff --git a/drivers/video/imx-ipu-fb.c b/drivers/video/imx-ipu-fb.c
index 2c25b81..426defc 100644
--- a/drivers/video/imx-ipu-fb.c
+++ b/drivers/video/imx-ipu-fb.c
@@ -34,12 +34,12 @@
#include <mach/clock.h>
struct ipu_fb_info {
+ struct fb_host fb_host; /**< myself */
void __iomem *regs;
void (*enable)(int enable);
- struct fb_info info;
- struct device_d *dev;
+ const struct fb_videomode *mode; /**< requested videomodue */
};
/* IPU DMA Controller channel definitions. */
@@ -413,29 +413,30 @@ static inline void reg_write(struct ipu_fb_info *fbi, u32 value,
writel(value, fbi->regs + reg);
}
+#define fb_info_to_imxfb_info(x) ((struct ipu_fb_info*)((x)->host))
+
/*
* sdc_init_panel() - initialize a synchronous LCD panel.
- * @width: width of panel in pixels.
- * @height: height of panel in pixels.
- * @pixel_fmt: pixel format of buffer as FOURCC ASCII code.
+ * @param info The framebuffer to work on
+ * @param pixel_fmt pixel format of buffer as FOURCC ASCII code.
* @return: 0 on success or negative error code on failure.
*/
static int sdc_init_panel(struct fb_info *info, enum pixel_fmt pixel_fmt)
{
- struct ipu_fb_info *fbi = info->priv;
- struct fb_videomode *mode = info->mode;
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
+ const struct fb_videomode *mode = fbi->mode;
u32 reg, old_conf, div;
enum ipu_panel panel = IPU_PANEL_TFT;
unsigned long pixel_clk;
/* Init panel size and blanking periods */
reg = ((mode->hsync_len - 1) << 26) |
- ((info->xres + mode->left_margin + mode->right_margin +
+ ((mode->xres + mode->left_margin + mode->right_margin +
mode->hsync_len - 1) << 16);
reg_write(fbi, reg, SDC_HOR_CONF);
reg = ((mode->vsync_len - 1) << 26) | SDC_V_SYNC_WIDTH_L |
- ((info->yres + mode->upper_margin + mode->lower_margin +
+ ((mode->yres + mode->upper_margin + mode->lower_margin +
mode->vsync_len - 1) << 16);
reg_write(fbi, reg, SDC_VER_CONF);
@@ -448,7 +449,7 @@ static int sdc_init_panel(struct fb_info *info, enum pixel_fmt pixel_fmt)
old_conf |= DI_D3_CLK_POL;
if (mode->sync & FB_SYNC_DATA_INVERT)
old_conf |= DI_D3_DATA_POL;
- if (mode->sync & FB_SYNC_OE_ACT_HIGH)
+ if (mode->sync & FB_SYNC_DE_HIGH_ACT)
old_conf |= DI_D3_DRDY_SHARP_POL;
reg_write(fbi, old_conf, DI_DISP_SIG_POL);
@@ -483,12 +484,12 @@ static int sdc_init_panel(struct fb_info *info, enum pixel_fmt pixel_fmt)
div = imx_get_lcdclk() * 16 / pixel_clk;
if (div < 0x40) { /* Divider less than 4 */
- dev_dbg(&info->dev,
+ dev_dbg(fbi->fb_host.hw_dev,
"InitPanel() - Pixel clock divider less than 4\n");
div = 0x40;
}
- dev_dbg(&info->dev, "pixel clk = %u, divider %u.%u\n",
+ dev_dbg(fbi->fb_host.hw_dev, "pixel clk = %u, divider %u.%u\n",
pixel_clk, div >> 4, (div & 7) * 125);
/*
@@ -588,19 +589,20 @@ static u32 dma_param_addr(enum ipu_channel channel)
return 0x10000 | (channel << 4);
}
-static void ipu_init_channel_buffer(struct ipu_fb_info *fbi,
+static void ipu_init_channel_buffer(struct fb_info *info,
enum ipu_channel channel, void *fbmem)
{
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
union chan_param_mem params = {};
u32 reg;
u32 stride_bytes;
- stride_bytes = fbi->info.xres * ((fbi->info.bits_per_pixel + 7) / 8);
+ stride_bytes = fbi->mode->xres * ((info->bits_per_pixel + 7) / 8);
stride_bytes = (stride_bytes + 3) & ~3;
/* Build parameter memory data for DMA channel */
- ipu_ch_param_set_size(¶ms, bpp_to_pixfmt(fbi->info.bits_per_pixel),
- fbi->info.xres, fbi->info.yres, stride_bytes);
+ ipu_ch_param_set_size(¶ms, bpp_to_pixfmt(info->bits_per_pixel),
+ fbi->mode->xres, fbi->mode->yres, stride_bytes);
ipu_ch_param_set_buffer(¶ms, fbmem, NULL);
params.pp.bam = 0;
/* Some channels (rotation) have restriction on burst length */
@@ -622,9 +624,10 @@ static void ipu_init_channel_buffer(struct ipu_fb_info *fbi,
reg_write(fbi, reg, IPU_CHA_DB_MODE_SEL);
}
-static void ipu_channel_set_priority(struct ipu_fb_info *fbi,
+static void ipu_channel_set_priority(struct fb_info *fb_info,
enum ipu_channel channel, int prio)
{
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(fb_info);
u32 reg;
reg = reg_read(fbi, IDMAC_CHA_PRI);
@@ -639,11 +642,13 @@ static void ipu_channel_set_priority(struct ipu_fb_info *fbi,
/*
* ipu_enable_channel() - enable an IPU channel.
+ * @param info The framebuffer to work on
* @channel: channel ID.
* @return: 0 on success or negative error code on failure.
*/
-static int ipu_enable_channel(struct ipu_fb_info *fbi, enum ipu_channel channel)
+static int ipu_enable_channel(struct fb_info *info, enum ipu_channel channel)
{
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
u32 reg;
/* Reset to buffer 0 */
@@ -651,7 +656,7 @@ static int ipu_enable_channel(struct ipu_fb_info *fbi, enum ipu_channel channel)
switch (channel) {
case IDMAC_SDC_0:
- ipu_channel_set_priority(fbi, channel, 1);
+ ipu_channel_set_priority(info, channel, 1);
break;
default:
break;
@@ -663,9 +668,10 @@ static int ipu_enable_channel(struct ipu_fb_info *fbi, enum ipu_channel channel)
return 0;
}
-static int ipu_update_channel_buffer(struct ipu_fb_info *fbi,
+static int ipu_update_channel_buffer(struct fb_info *info,
enum ipu_channel channel, void *buf)
{
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
u32 reg;
reg = reg_read(fbi, IPU_CHA_BUF0_RDY);
@@ -679,16 +685,17 @@ static int ipu_update_channel_buffer(struct ipu_fb_info *fbi,
return 0;
}
-static int idmac_tx_submit(struct ipu_fb_info *fbi, enum ipu_channel channel,
+static int idmac_tx_submit(struct fb_info *info, enum ipu_channel channel,
void *buf)
{
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
int ret;
- ipu_init_channel_buffer(fbi, channel, buf);
+ ipu_init_channel_buffer(info, channel, buf);
/* ipu_idmac.c::ipu_submit_channel_buffers() */
- ret = ipu_update_channel_buffer(fbi, channel, buf);
+ ret = ipu_update_channel_buffer(info, channel, buf);
if (ret < 0)
return ret;
@@ -697,16 +704,17 @@ static int idmac_tx_submit(struct ipu_fb_info *fbi, enum ipu_channel channel,
reg_write(fbi, 1UL << channel, IPU_CHA_BUF0_RDY);
- ret = ipu_enable_channel(fbi, channel);
+ ret = ipu_enable_channel(info, channel);
return ret;
}
-static void sdc_enable_channel(struct ipu_fb_info *fbi, void *fbmem)
+static void sdc_enable_channel(struct fb_info *info, void *fbmem)
{
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
int ret;
u32 reg;
- ret = idmac_tx_submit(fbi, IDMAC_SDC_0, fbmem);
+ ret = idmac_tx_submit(info, IDMAC_SDC_0, fbmem);
/* mx3fb.c::sdc_fb_init() */
if (ret >= 0) {
@@ -724,13 +732,14 @@ static void sdc_enable_channel(struct ipu_fb_info *fbi, void *fbmem)
/*
* mx3fb_set_par() - set framebuffer parameters and change the operating mode.
+ * @param info The framebuffer to work on
* @return: 0 on success or negative error code on failure.
*/
static int mx3fb_set_par(struct fb_info *info)
{
- struct ipu_fb_info *fbi = info->priv;
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
struct imx_ipu_fb_rgb *rgb;
- struct fb_videomode *mode = info->mode;
+ const struct fb_videomode *mode = fbi->mode;
int ret;
ret = sdc_init_panel(info, IPU_PIX_FMT_RGB666);
@@ -766,10 +775,45 @@ static int mx3fb_set_par(struct fb_info *info)
return 0;
}
+static int ipu_fb_initialize_mode(struct fb_info *fb_info, const struct fb_videomode *mode)
+{
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(fb_info);
+ unsigned size;
+
+ /*
+ * we need at least this amount of memory for the framebuffer
+ */
+ size = mode->xres * mode->yres * (fb_info->bits_per_pixel >> 3);
+ if (fb_info->fb_dev->size != 0) {
+ if (size > fb_info->fb_dev->size) {
+ pr_err("Cannot initialize video mode '%s': Its too large. "
+ "Required bytes are %u, available only %u\n",
+ mode->name, size, fb_info->fb_dev->size);
+ return -EINVAL;
+ }
+ } else
+ fb_info->fb_dev->size = size;
+
+ /*
+ * if no framebuffer memory was specified yet, allocate one,
+ * and allocate more memory, on user request
+ */
+ if (fb_info->fb_dev->map_base == 0U /* FIXME should be 'NULL'*/)
+ fb_info->fb_dev->map_base = (unsigned long)xzalloc(fb_info->fb_dev->size);
+
+#if 0
+ /* FIXME why here? Its also called in ipu_fb_enable() */
+ sdc_enable_channel(fbi, fb_info->fb_dev->map_base);
+#endif
+ fbi->mode = mode;
+
+ return 0;
+}
+
/* References in this function refer to respective Linux kernel sources */
static void ipu_fb_enable(struct fb_info *info)
{
- struct ipu_fb_info *fbi = info->priv;
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
u32 reg;
@@ -825,7 +869,7 @@ static void ipu_fb_enable(struct fb_info *info)
mx3fb_set_par(info);
- sdc_enable_channel(fbi, info->screen_base);
+ sdc_enable_channel(info, (void*)info->fb_dev->map_base);
/*
* Linux driver calls sdc_set_brightness() here again,
@@ -837,7 +881,7 @@ static void ipu_fb_enable(struct fb_info *info)
static void ipu_fb_disable(struct fb_info *info)
{
- struct ipu_fb_info *fbi = info->priv;
+ struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
u32 reg;
printf("%s\n", __func__);
@@ -850,54 +894,38 @@ static void ipu_fb_disable(struct fb_info *info)
reg_write(fbi, reg, SDC_COM_CONF);
}
-static struct fb_ops imxfb_ops = {
- .fb_enable = ipu_fb_enable,
- .fb_disable = ipu_fb_disable,
-};
-
static int imxfb_probe(struct device_d *dev)
{
struct ipu_fb_info *fbi;
- struct fb_info *info;
+ struct device_d *fb_dev;
const struct imx_ipu_fb_platform_data *pdata = dev->platform_data;
- int ret;
if (!pdata)
return -ENODEV;
fbi = xzalloc(sizeof(*fbi));
- info = &fbi->info;
+
+ /* add runtime hardware info */
+ fbi->fb_host.hw_dev = dev;
+ fbi->fb_host.fb_mode = ipu_fb_initialize_mode;
+ fbi->fb_host.fb_enable = ipu_fb_enable;
+ fbi->fb_host.fb_disable = ipu_fb_disable;
+ fbi->fb_host.fb_setcolreg = NULL;
fbi->regs = (void *)dev->map_base;
- fbi->dev = dev;
- info->priv = fbi;
- info->mode = pdata->mode;
- info->xres = pdata->mode->xres;
- info->yres = pdata->mode->yres;
- info->bits_per_pixel = pdata->bpp;
- info->fbops = &imxfb_ops;
- fbi->enable = pdata->enable;
- dev_info(dev, "i.MX Framebuffer driver\n");
+ /* add runtime video info */
+ fbi->fb_host.mode = pdata->mode;
+ /* to be backward compatible */
+ fbi->fb_host.mode_cnt = pdata->mode_cnt == 0 ? 1 : pdata->mode_cnt;
+ fbi->fb_host.bits_per_pixel = pdata->bpp;
- /*
- * Use a given frambuffer or reserve some
- * memory for screen usage
- */
- fbi->info.screen_base = pdata->framebuffer;
- if (fbi->info.screen_base == NULL) {
- fbi->info.screen_base = malloc(info->xres * info->yres *
- (info->bits_per_pixel >> 3));
- if (!fbi->info.screen_base)
- return -ENOMEM;
- }
-
- sdc_enable_channel(fbi, info->screen_base);
+ dev_info(dev, "i.MX Framebuffer driver\n");
- ret = register_framebuffer(&fbi->info);
- if (ret < 0) {
+ fb_dev = register_framebuffer(&fbi->fb_host, pdata->framebuffer, 0);
+ if (fb_dev == NULL) {
dev_err(dev, "failed to register framebuffer\n");
- return ret;
+ return -EINVAL;
}
return 0;
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 07/11] Adapt the existing imx-ipu fb driver to support runtime videomode selection
2010-10-22 16:53 ` [PATCH 07/11] Adapt the existing imx-ipu " Juergen Beisert
@ 2010-10-22 17:43 ` Sascha Hauer
2010-10-23 10:36 ` Juergen Beisert
0 siblings, 1 reply; 23+ messages in thread
From: Sascha Hauer @ 2010-10-22 17:43 UTC (permalink / raw)
To: Juergen Beisert; +Cc: barebox
On Fri, Oct 22, 2010 at 06:53:21PM +0200, Juergen Beisert wrote:
> Adapt the API to the new framebuffer videomode selection at runtime. If the new
> feature is not used, there is no visible change at runtime for platforms using
> this driver.
This conflicts with the ipu fb patch I posted today.
Sascha
>
> NOTE: Due to the lack of hardware, this is compile time tested only.
>
> This is patch 5 of 7 to keep the repository bisectable.
>
> Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
> ---
> arch/arm/boards/freescale-mx35-3-stack/3stack.c | 2 +-
> arch/arm/boards/pcm043/pcm043.c | 2 +-
> arch/arm/mach-imx/include/mach/imx-ipu-fb.h | 12 +--
> drivers/video/imx-ipu-fb.c | 156 +++++++++++++---------
> 4 files changed, 96 insertions(+), 76 deletions(-)
>
> diff --git a/arch/arm/boards/freescale-mx35-3-stack/3stack.c b/arch/arm/boards/freescale-mx35-3-stack/3stack.c
> index d6699cd..fb40f50 100644
> --- a/arch/arm/boards/freescale-mx35-3-stack/3stack.c
> +++ b/arch/arm/boards/freescale-mx35-3-stack/3stack.c
> @@ -139,7 +139,7 @@ static struct fb_videomode CTP_CLAA070LC0ACW = {
> .lower_margin = 10, /* whole frame should have 500 lines */
> .hsync_len = 1, /* note: DE only display */
> .vsync_len = 1, /* note: DE only display */
> - .sync = FB_SYNC_CLK_IDLE_EN | FB_SYNC_OE_ACT_HIGH,
> + .sync = FB_SYNC_CLK_IDLE_EN | FB_SYNC_DE_HIGH_ACT,
> .vmode = FB_VMODE_NONINTERLACED,
> .flag = 0,
> };
> diff --git a/arch/arm/boards/pcm043/pcm043.c b/arch/arm/boards/pcm043/pcm043.c
> index 5932f95..7e63cc5 100644
> --- a/arch/arm/boards/pcm043/pcm043.c
> +++ b/arch/arm/boards/pcm043/pcm043.c
> @@ -124,7 +124,7 @@ static struct fb_videomode pcm043_fb_mode = {
> .lower_margin = 40,
> .hsync_len = 96,
> .vsync_len = 1,
> - .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
> + .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_DE_HIGH_ACT,
> .vmode = FB_VMODE_NONINTERLACED,
> .flag = 0,
> };
> diff --git a/arch/arm/mach-imx/include/mach/imx-ipu-fb.h b/arch/arm/mach-imx/include/mach/imx-ipu-fb.h
> index 8e1cc87..ce95243 100644
> --- a/arch/arm/mach-imx/include/mach/imx-ipu-fb.h
> +++ b/arch/arm/mach-imx/include/mach/imx-ipu-fb.h
> @@ -12,20 +12,12 @@
>
> #include <fb.h>
>
> -/* Proprietary FB_SYNC_ flags */
> -#define FB_SYNC_OE_ACT_HIGH 0x80000000
> -#define FB_SYNC_CLK_INVERT 0x40000000
> -#define FB_SYNC_DATA_INVERT 0x20000000
> -#define FB_SYNC_CLK_IDLE_EN 0x10000000
> -#define FB_SYNC_SHARP_MODE 0x08000000
> -#define FB_SYNC_SWAP_RGB 0x04000000
> -#define FB_SYNC_CLK_SEL_EN 0x02000000
> -
> /*
> - * struct mx3fb_platform_data - mx3fb platform data
> + * struct imx_ipu_fb_platform_data - imx-ipu-fb's platform data
> */
> struct imx_ipu_fb_platform_data {
> struct fb_videomode *mode;
> + unsigned mode_cnt; /**< number of entries in 'mode' */
> unsigned char bpp;
> void __iomem *framebuffer;
> /** hook to enable backlight and stuff */
> diff --git a/drivers/video/imx-ipu-fb.c b/drivers/video/imx-ipu-fb.c
> index 2c25b81..426defc 100644
> --- a/drivers/video/imx-ipu-fb.c
> +++ b/drivers/video/imx-ipu-fb.c
> @@ -34,12 +34,12 @@
> #include <mach/clock.h>
>
> struct ipu_fb_info {
> + struct fb_host fb_host; /**< myself */
> void __iomem *regs;
>
> void (*enable)(int enable);
>
> - struct fb_info info;
> - struct device_d *dev;
> + const struct fb_videomode *mode; /**< requested videomodue */
> };
>
> /* IPU DMA Controller channel definitions. */
> @@ -413,29 +413,30 @@ static inline void reg_write(struct ipu_fb_info *fbi, u32 value,
> writel(value, fbi->regs + reg);
> }
>
> +#define fb_info_to_imxfb_info(x) ((struct ipu_fb_info*)((x)->host))
> +
> /*
> * sdc_init_panel() - initialize a synchronous LCD panel.
> - * @width: width of panel in pixels.
> - * @height: height of panel in pixels.
> - * @pixel_fmt: pixel format of buffer as FOURCC ASCII code.
> + * @param info The framebuffer to work on
> + * @param pixel_fmt pixel format of buffer as FOURCC ASCII code.
> * @return: 0 on success or negative error code on failure.
> */
> static int sdc_init_panel(struct fb_info *info, enum pixel_fmt pixel_fmt)
> {
> - struct ipu_fb_info *fbi = info->priv;
> - struct fb_videomode *mode = info->mode;
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
> + const struct fb_videomode *mode = fbi->mode;
> u32 reg, old_conf, div;
> enum ipu_panel panel = IPU_PANEL_TFT;
> unsigned long pixel_clk;
>
> /* Init panel size and blanking periods */
> reg = ((mode->hsync_len - 1) << 26) |
> - ((info->xres + mode->left_margin + mode->right_margin +
> + ((mode->xres + mode->left_margin + mode->right_margin +
> mode->hsync_len - 1) << 16);
> reg_write(fbi, reg, SDC_HOR_CONF);
>
> reg = ((mode->vsync_len - 1) << 26) | SDC_V_SYNC_WIDTH_L |
> - ((info->yres + mode->upper_margin + mode->lower_margin +
> + ((mode->yres + mode->upper_margin + mode->lower_margin +
> mode->vsync_len - 1) << 16);
> reg_write(fbi, reg, SDC_VER_CONF);
>
> @@ -448,7 +449,7 @@ static int sdc_init_panel(struct fb_info *info, enum pixel_fmt pixel_fmt)
> old_conf |= DI_D3_CLK_POL;
> if (mode->sync & FB_SYNC_DATA_INVERT)
> old_conf |= DI_D3_DATA_POL;
> - if (mode->sync & FB_SYNC_OE_ACT_HIGH)
> + if (mode->sync & FB_SYNC_DE_HIGH_ACT)
> old_conf |= DI_D3_DRDY_SHARP_POL;
> reg_write(fbi, old_conf, DI_DISP_SIG_POL);
>
> @@ -483,12 +484,12 @@ static int sdc_init_panel(struct fb_info *info, enum pixel_fmt pixel_fmt)
> div = imx_get_lcdclk() * 16 / pixel_clk;
>
> if (div < 0x40) { /* Divider less than 4 */
> - dev_dbg(&info->dev,
> + dev_dbg(fbi->fb_host.hw_dev,
> "InitPanel() - Pixel clock divider less than 4\n");
> div = 0x40;
> }
>
> - dev_dbg(&info->dev, "pixel clk = %u, divider %u.%u\n",
> + dev_dbg(fbi->fb_host.hw_dev, "pixel clk = %u, divider %u.%u\n",
> pixel_clk, div >> 4, (div & 7) * 125);
>
> /*
> @@ -588,19 +589,20 @@ static u32 dma_param_addr(enum ipu_channel channel)
> return 0x10000 | (channel << 4);
> }
>
> -static void ipu_init_channel_buffer(struct ipu_fb_info *fbi,
> +static void ipu_init_channel_buffer(struct fb_info *info,
> enum ipu_channel channel, void *fbmem)
> {
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
> union chan_param_mem params = {};
> u32 reg;
> u32 stride_bytes;
>
> - stride_bytes = fbi->info.xres * ((fbi->info.bits_per_pixel + 7) / 8);
> + stride_bytes = fbi->mode->xres * ((info->bits_per_pixel + 7) / 8);
> stride_bytes = (stride_bytes + 3) & ~3;
>
> /* Build parameter memory data for DMA channel */
> - ipu_ch_param_set_size(¶ms, bpp_to_pixfmt(fbi->info.bits_per_pixel),
> - fbi->info.xres, fbi->info.yres, stride_bytes);
> + ipu_ch_param_set_size(¶ms, bpp_to_pixfmt(info->bits_per_pixel),
> + fbi->mode->xres, fbi->mode->yres, stride_bytes);
> ipu_ch_param_set_buffer(¶ms, fbmem, NULL);
> params.pp.bam = 0;
> /* Some channels (rotation) have restriction on burst length */
> @@ -622,9 +624,10 @@ static void ipu_init_channel_buffer(struct ipu_fb_info *fbi,
> reg_write(fbi, reg, IPU_CHA_DB_MODE_SEL);
> }
>
> -static void ipu_channel_set_priority(struct ipu_fb_info *fbi,
> +static void ipu_channel_set_priority(struct fb_info *fb_info,
> enum ipu_channel channel, int prio)
> {
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(fb_info);
> u32 reg;
>
> reg = reg_read(fbi, IDMAC_CHA_PRI);
> @@ -639,11 +642,13 @@ static void ipu_channel_set_priority(struct ipu_fb_info *fbi,
>
> /*
> * ipu_enable_channel() - enable an IPU channel.
> + * @param info The framebuffer to work on
> * @channel: channel ID.
> * @return: 0 on success or negative error code on failure.
> */
> -static int ipu_enable_channel(struct ipu_fb_info *fbi, enum ipu_channel channel)
> +static int ipu_enable_channel(struct fb_info *info, enum ipu_channel channel)
> {
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
> u32 reg;
>
> /* Reset to buffer 0 */
> @@ -651,7 +656,7 @@ static int ipu_enable_channel(struct ipu_fb_info *fbi, enum ipu_channel channel)
>
> switch (channel) {
> case IDMAC_SDC_0:
> - ipu_channel_set_priority(fbi, channel, 1);
> + ipu_channel_set_priority(info, channel, 1);
> break;
> default:
> break;
> @@ -663,9 +668,10 @@ static int ipu_enable_channel(struct ipu_fb_info *fbi, enum ipu_channel channel)
> return 0;
> }
>
> -static int ipu_update_channel_buffer(struct ipu_fb_info *fbi,
> +static int ipu_update_channel_buffer(struct fb_info *info,
> enum ipu_channel channel, void *buf)
> {
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
> u32 reg;
>
> reg = reg_read(fbi, IPU_CHA_BUF0_RDY);
> @@ -679,16 +685,17 @@ static int ipu_update_channel_buffer(struct ipu_fb_info *fbi,
> return 0;
> }
>
> -static int idmac_tx_submit(struct ipu_fb_info *fbi, enum ipu_channel channel,
> +static int idmac_tx_submit(struct fb_info *info, enum ipu_channel channel,
> void *buf)
> {
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
> int ret;
>
> - ipu_init_channel_buffer(fbi, channel, buf);
> + ipu_init_channel_buffer(info, channel, buf);
>
>
> /* ipu_idmac.c::ipu_submit_channel_buffers() */
> - ret = ipu_update_channel_buffer(fbi, channel, buf);
> + ret = ipu_update_channel_buffer(info, channel, buf);
> if (ret < 0)
> return ret;
>
> @@ -697,16 +704,17 @@ static int idmac_tx_submit(struct ipu_fb_info *fbi, enum ipu_channel channel,
> reg_write(fbi, 1UL << channel, IPU_CHA_BUF0_RDY);
>
>
> - ret = ipu_enable_channel(fbi, channel);
> + ret = ipu_enable_channel(info, channel);
> return ret;
> }
>
> -static void sdc_enable_channel(struct ipu_fb_info *fbi, void *fbmem)
> +static void sdc_enable_channel(struct fb_info *info, void *fbmem)
> {
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
> int ret;
> u32 reg;
>
> - ret = idmac_tx_submit(fbi, IDMAC_SDC_0, fbmem);
> + ret = idmac_tx_submit(info, IDMAC_SDC_0, fbmem);
>
> /* mx3fb.c::sdc_fb_init() */
> if (ret >= 0) {
> @@ -724,13 +732,14 @@ static void sdc_enable_channel(struct ipu_fb_info *fbi, void *fbmem)
>
> /*
> * mx3fb_set_par() - set framebuffer parameters and change the operating mode.
> + * @param info The framebuffer to work on
> * @return: 0 on success or negative error code on failure.
> */
> static int mx3fb_set_par(struct fb_info *info)
> {
> - struct ipu_fb_info *fbi = info->priv;
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
> struct imx_ipu_fb_rgb *rgb;
> - struct fb_videomode *mode = info->mode;
> + const struct fb_videomode *mode = fbi->mode;
> int ret;
>
> ret = sdc_init_panel(info, IPU_PIX_FMT_RGB666);
> @@ -766,10 +775,45 @@ static int mx3fb_set_par(struct fb_info *info)
> return 0;
> }
>
> +static int ipu_fb_initialize_mode(struct fb_info *fb_info, const struct fb_videomode *mode)
> +{
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(fb_info);
> + unsigned size;
> +
> + /*
> + * we need at least this amount of memory for the framebuffer
> + */
> + size = mode->xres * mode->yres * (fb_info->bits_per_pixel >> 3);
> + if (fb_info->fb_dev->size != 0) {
> + if (size > fb_info->fb_dev->size) {
> + pr_err("Cannot initialize video mode '%s': Its too large. "
> + "Required bytes are %u, available only %u\n",
> + mode->name, size, fb_info->fb_dev->size);
> + return -EINVAL;
> + }
> + } else
> + fb_info->fb_dev->size = size;
> +
> + /*
> + * if no framebuffer memory was specified yet, allocate one,
> + * and allocate more memory, on user request
> + */
> + if (fb_info->fb_dev->map_base == 0U /* FIXME should be 'NULL'*/)
> + fb_info->fb_dev->map_base = (unsigned long)xzalloc(fb_info->fb_dev->size);
> +
> +#if 0
> + /* FIXME why here? Its also called in ipu_fb_enable() */
> + sdc_enable_channel(fbi, fb_info->fb_dev->map_base);
> +#endif
> + fbi->mode = mode;
> +
> + return 0;
> +}
> +
> /* References in this function refer to respective Linux kernel sources */
> static void ipu_fb_enable(struct fb_info *info)
> {
> - struct ipu_fb_info *fbi = info->priv;
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
>
> u32 reg;
>
> @@ -825,7 +869,7 @@ static void ipu_fb_enable(struct fb_info *info)
>
> mx3fb_set_par(info);
>
> - sdc_enable_channel(fbi, info->screen_base);
> + sdc_enable_channel(info, (void*)info->fb_dev->map_base);
>
> /*
> * Linux driver calls sdc_set_brightness() here again,
> @@ -837,7 +881,7 @@ static void ipu_fb_enable(struct fb_info *info)
>
> static void ipu_fb_disable(struct fb_info *info)
> {
> - struct ipu_fb_info *fbi = info->priv;
> + struct ipu_fb_info *fbi = fb_info_to_imxfb_info(info);
> u32 reg;
>
> printf("%s\n", __func__);
> @@ -850,54 +894,38 @@ static void ipu_fb_disable(struct fb_info *info)
> reg_write(fbi, reg, SDC_COM_CONF);
> }
>
> -static struct fb_ops imxfb_ops = {
> - .fb_enable = ipu_fb_enable,
> - .fb_disable = ipu_fb_disable,
> -};
> -
> static int imxfb_probe(struct device_d *dev)
> {
> struct ipu_fb_info *fbi;
> - struct fb_info *info;
> + struct device_d *fb_dev;
> const struct imx_ipu_fb_platform_data *pdata = dev->platform_data;
> - int ret;
>
> if (!pdata)
> return -ENODEV;
>
> fbi = xzalloc(sizeof(*fbi));
> - info = &fbi->info;
> +
> + /* add runtime hardware info */
> + fbi->fb_host.hw_dev = dev;
> + fbi->fb_host.fb_mode = ipu_fb_initialize_mode;
> + fbi->fb_host.fb_enable = ipu_fb_enable;
> + fbi->fb_host.fb_disable = ipu_fb_disable;
> + fbi->fb_host.fb_setcolreg = NULL;
>
> fbi->regs = (void *)dev->map_base;
> - fbi->dev = dev;
> - info->priv = fbi;
> - info->mode = pdata->mode;
> - info->xres = pdata->mode->xres;
> - info->yres = pdata->mode->yres;
> - info->bits_per_pixel = pdata->bpp;
> - info->fbops = &imxfb_ops;
> - fbi->enable = pdata->enable;
>
> - dev_info(dev, "i.MX Framebuffer driver\n");
> + /* add runtime video info */
> + fbi->fb_host.mode = pdata->mode;
> + /* to be backward compatible */
> + fbi->fb_host.mode_cnt = pdata->mode_cnt == 0 ? 1 : pdata->mode_cnt;
> + fbi->fb_host.bits_per_pixel = pdata->bpp;
>
> - /*
> - * Use a given frambuffer or reserve some
> - * memory for screen usage
> - */
> - fbi->info.screen_base = pdata->framebuffer;
> - if (fbi->info.screen_base == NULL) {
> - fbi->info.screen_base = malloc(info->xres * info->yres *
> - (info->bits_per_pixel >> 3));
> - if (!fbi->info.screen_base)
> - return -ENOMEM;
> - }
> -
> - sdc_enable_channel(fbi, info->screen_base);
> + dev_info(dev, "i.MX Framebuffer driver\n");
>
> - ret = register_framebuffer(&fbi->info);
> - if (ret < 0) {
> + fb_dev = register_framebuffer(&fbi->fb_host, pdata->framebuffer, 0);
> + if (fb_dev == NULL) {
> dev_err(dev, "failed to register framebuffer\n");
> - return ret;
> + return -EINVAL;
> }
>
> return 0;
> --
> 1.7.2.3
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 07/11] Adapt the existing imx-ipu fb driver to support runtime videomode selection
2010-10-22 17:43 ` Sascha Hauer
@ 2010-10-23 10:36 ` Juergen Beisert
0 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-23 10:36 UTC (permalink / raw)
To: barebox
Sascha Hauer wrote:
> On Fri, Oct 22, 2010 at 06:53:21PM +0200, Juergen Beisert wrote:
> > Adapt the API to the new framebuffer videomode selection at runtime. If
> > the new feature is not used, there is no visible change at runtime for
> > platforms using this driver.
>
> This conflicts with the ipu fb patch I posted today.
I see. I generated this list on to of barebox-next. Next try...
jbe
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | Phone: +49-8766-939 228 |
Vertretung Sued/Muenchen, Germany | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de/ |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 08/11] Add a video driver for S3C2440 bases platforms
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
` (6 preceding siblings ...)
2010-10-22 16:53 ` [PATCH 07/11] Adapt the existing imx-ipu " Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 18:56 ` Sascha Hauer
2010-10-22 16:53 ` [PATCH 09/11] STM378x: Add video driver for this platform Juergen Beisert
` (2 subsequent siblings)
10 siblings, 1 reply; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox; +Cc: Juergen Beisert
[-- Attachment #1: Type: text/plain, Size: 15246 bytes --]
From: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
---
arch/arm/mach-s3c24xx/include/mach/fb.h | 40 +++
drivers/video/Kconfig | 6 +
drivers/video/Makefile | 1 +
drivers/video/s3c.c | 454 +++++++++++++++++++++++++++++++
4 files changed, 501 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-s3c24xx/include/mach/fb.h
create mode 100644 drivers/video/s3c.c
diff --git a/arch/arm/mach-s3c24xx/include/mach/fb.h b/arch/arm/mach-s3c24xx/include/mach/fb.h
new file mode 100644
index 0000000..eec6164
--- /dev/null
+++ b/arch/arm/mach-s3c24xx/include/mach/fb.h
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2010 Juergen Beisert
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef __MACH_FB_H_
+# define __MACH_FB_H_
+
+#include <fb.h>
+
+struct s3c_fb_platform_data {
+
+ const struct fb_videomode *mode_list;
+ unsigned mode_cnt;
+
+ int passive_display; /**< enable support for STN or CSTN displays */
+
+ void *framebuffer; /**< force framebuffer base address */
+ unsigned size; /**< force framebuffer size */
+
+ /** hook to enable backlight and stuff */
+ void (*enable)(int);
+};
+
+#endif /* __MACH_FB_H_ */
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index f96accc..64f68c4 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -49,4 +49,10 @@ config DRIVER_VIDEO_IMX_IPU
Add support for the IPU framebuffer device found on
i.MX31 and i.MX35 CPUs.
+config S3C_VIDEO
+ bool "S3C244x framebuffer driver"
+ depends on ARCH_S3C24xx
+ help
+ Add support for the S3C244x LCD controller.
+
endif
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 179f0c4..4287fc8 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -2,3 +2,4 @@ obj-$(CONFIG_VIDEO) += fb.o
obj-$(CONFIG_DRIVER_VIDEO_IMX) += imx.o
obj-$(CONFIG_DRIVER_VIDEO_IMX_IPU) += imx-ipu-fb.o
+obj-$(CONFIG_S3C_VIDEO) += s3c.o
diff --git a/drivers/video/s3c.c b/drivers/video/s3c.c
new file mode 100644
index 0000000..cd0f220
--- /dev/null
+++ b/drivers/video/s3c.c
@@ -0,0 +1,454 @@
+/*
+ * Copyright (C) 2010 Juergen Beisert
+ *
+ * This driver is based on a patch found in the web:
+ * (C) Copyright 2006 by OpenMoko, Inc.
+ * Author: Harald Welte <laforge at openmoko.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+/* #define DEBUG */
+
+#include <common.h>
+#include <init.h>
+#include <fb.h>
+#include <driver.h>
+#include <malloc.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <mach/gpio.h>
+#include <mach/s3c24xx-generic.h>
+#include <mach/s3c24x0-clocks.h>
+#include <mach/fb.h>
+
+#define LCDCON1 0x00
+# define PNRMODE(x) (((x) & 3) << 5)
+# define BPPMODE(x) (((x) & 0xf) << 1)
+# define SET_CLKVAL(x) (((x) & 0x3ff) << 8)
+# define GET_CLKVAL(x) (((x) >> 8) & 0x3ff)
+# define ENVID (1 << 0)
+
+#define LCDCON2 0x04
+# define SET_VBPD(x) (((x) & 0xff) << 24)
+# define SET_LINEVAL(x) (((x) & 0x3ff) << 14)
+# define SET_VFPD(x) (((x) & 0xff) << 6)
+# define SET_VSPW(x) ((x) & 0x3f)
+
+#define LCDCON3 0x08
+# define SET_HBPD(x) (((x) & 0x7f) << 19)
+# define SET_HOZVAL(x) (((x) & 0x7ff) << 8)
+# define SET_HFPD(x) ((x) & 0xff)
+
+#define LCDCON4 0x0c
+# define SET_HSPW(x) ((x) & 0xff)
+
+#define LCDCON5 0x10
+# define BPP24BL (1 << 12)
+# define FRM565 (1 << 11)
+# define INV_CLK (1 << 10)
+# define INV_HS (1 << 9)
+# define INV_VS (1 << 8)
+# define INV_DTA (1 << 7)
+# define INV_DE (1 << 6)
+# define INV_PWREN (1 << 5)
+# define INV_LEND (1 << 4) /* FIXME */
+# define ENA_PWREN (1 << 3)
+# define ENA_LEND (1 << 2) /* FIXME */
+# define BSWP (1 << 1)
+# define HWSWP (1 << 0)
+
+#define LCDSADDR1 0x14
+# define SET_LCDBANK(x) (((x) & 0x1ff) << 21)
+# define GET_LCDBANK(x) (((x) >> 21) & 0x1ff)
+# define SET_LCDBASEU(x) ((x) & 0x1fffff)
+# define GET_LCDBASEU(x) ((x) & 0x1fffff)
+
+#define LCDSADDR2 0x18
+# define SET_LCDBASEL(x) ((x) & 0x1fffff)
+# define GET_LCDBASEL(x) ((x) & 0x1fffff)
+
+#define LCDSADDR3 0x1c
+# define SET_OFFSIZE(x) (((x) & 0x7ff) << 11)
+# define GET_OFFSIZE(x) (((x) >> 11) & 0x7ff)
+# define SET_PAGE_WIDTH(x) ((x) & 0x3ff)
+# define GET_PAGE_WIDTH(x) ((x) & 0x3ff)
+
+#define RED_LUT 0x20
+#define GREEN_LUT 0x24
+#define BLUE_LUT 0x28
+
+#define DITHMODE 0x4c
+
+#define TPAL 0x50
+
+#define LCDINTPND 0x54
+
+#define LCDSRCPND 0x58
+
+#define LCDINTMSK 0x5c
+# define FIWSEL (1 << 2)
+
+#define TCONSEL 0x60
+
+#define RED 0
+#define GREEN 1
+#define BLUE 2
+#define TRANSP 3
+
+struct s3cfb_host {
+ struct fb_host fb_data;
+ struct device_d *hw_dev;
+ void __iomem *base;
+};
+
+#define fb_info_to_s3cfb_host(x) ((struct s3cfb_host*)((x)->host))
+#define s3cfb_host_to_s3c_fb_platform_data(x) ((struct s3c_fb_platform_data*)((x)->hw_dev->platform_data))
+
+/* the RGB565 true colour mode */
+static const struct fb_bitfield def_rgb565[] = {
+ [RED] = {
+ .offset = 11,
+ .length = 5,
+ },
+ [GREEN] = {
+ .offset = 5,
+ .length = 6,
+ },
+ [BLUE] = {
+ .offset = 0,
+ .length = 5,
+ },
+ [TRANSP] = { /* no support for transparency */
+ .length = 0,
+ }
+};
+
+/* the RGB888 true colour mode */
+static const struct fb_bitfield def_rgb888[] = {
+ [RED] = {
+ .offset = 16,
+ .length = 8,
+ },
+ [GREEN] = {
+ .offset = 8,
+ .length = 8,
+ },
+ [BLUE] = {
+ .offset = 0,
+ .length = 8,
+ },
+ [TRANSP] = { /* no support for transparency */
+ .length = 0,
+ }
+};
+
+/**
+ * @param fb_info Framebuffer information
+ */
+static void s3cfb_enable_controller(struct fb_info *fb_info)
+{
+ struct s3cfb_host *fbh = fb_info_to_s3cfb_host(fb_info);
+ struct s3c_fb_platform_data *pdata = s3cfb_host_to_s3c_fb_platform_data(fbh);
+ uint32_t con1;
+
+ pr_debug("%s called\n", __func__);
+
+ con1 = readl(fbh->base + LCDCON1);
+
+ con1 |= ENVID;
+
+ writel(con1, fbh->base + LCDCON1);
+
+ if (pdata->enable)
+ (pdata->enable)(1);
+}
+
+/**
+ * @param fb_info Framebuffer information
+ */
+static void s3cfb_disable_controller(struct fb_info *fb_info)
+{
+ struct s3cfb_host *fbh = fb_info_to_s3cfb_host(fb_info);
+ struct s3c_fb_platform_data *pdata = s3cfb_host_to_s3c_fb_platform_data(fbh);
+ uint32_t con1;
+
+ pr_debug("%s called\n", __func__);
+
+ if (pdata->enable)
+ (pdata->enable)(0);
+
+ con1 = readl(fbh->base + LCDCON1);
+
+ con1 &= ~ENVID;
+
+ writel(con1, fbh->base + LCDCON1);
+}
+
+/**
+ * Prepare the video hardware for a specified video mode
+ * @param fb_info Framebuffer information
+ * @param mode The video mode description to initialize
+ * @return 0 on success
+ *
+ * FIXME Diese Routine darf die Pinx nach drau�en nicht aktivieren. Zur Zeit macht sie das!
+ */
+static int s3cfb_initialize_mode(struct fb_info *fb_info, const struct fb_videomode *mode)
+{
+ struct s3cfb_host *fbh = fb_info_to_s3cfb_host(fb_info);
+ struct s3c_fb_platform_data *pdata = s3cfb_host_to_s3c_fb_platform_data(fbh);
+ unsigned size, hclk, div;
+ uint32_t con1, con2, con3, con4, con5 = 0;
+
+ pr_debug("%s called\n", __func__);
+
+ if (pdata->passive_display != 0) {
+ pr_err("Passive displays are currently not supported\n");
+ return -EINVAL;
+ }
+
+ /*
+ * we need at least this amount of memory for the framebuffer
+ */
+ size = mode->xres * mode->yres * (fb_info->bits_per_pixel >> 3);
+ if (fb_info->fb_dev->size != 0) {
+ if (size > fb_info->fb_dev->size) {
+ pr_err("Cannot initialize video mode '%s': Its too large. "
+ "Required bytes are %u, available only %u\n",
+ mode->name, size, fb_info->fb_dev->size);
+ return -EINVAL;
+ }
+ } else
+ fb_info->fb_dev->size = size;
+
+ /*
+ * if no framebuffer memory was specified yet, allocate one,
+ * and allocate more memory, on user request
+ */
+ if (fb_info->fb_dev->map_base == 0U)
+ fb_info->fb_dev->map_base = (resource_size_t)xzalloc(fb_info->fb_dev->size);
+
+ /* its useful to enable the unit's clock */
+ s3c244x_mod_clock(CLK_LCDC, 1);
+
+ /* ensure video output is _off_ */
+ writel(0x00000000, fbh->base + LCDCON1);
+
+ hclk = s3c24xx_get_hclk() / 1000U; /* hclk in kHz */
+ div = hclk / PICOS2KHZ(mode->pixclock);
+ if (div < 3)
+ div = 3;
+ /* pixel clock is: (hclk) / ((div + 1) * 2) */
+ div += 1;
+ div >>= 1;
+ div -= 1;
+
+ con1 = PNRMODE(3) | SET_CLKVAL(div); /* PNRMODE=3 is TFT */
+
+ switch (fb_info->bits_per_pixel) {
+#if 0
+ /* TODO add CLUT based modes */
+ case 1:
+ con1 |= BPPMODE(8);
+ break;
+ case 2:
+ con1 |= BPPMODE(9);
+ break;
+ case 4:
+ con1 |= BPPMODE(10);
+ break;
+ case 8:
+ con1 |= BPPMODE(11);
+ break;
+#endif
+ case 16:
+ con1 |= BPPMODE(12);
+ con5 |= FRM565;
+ fb_info->red = def_rgb565[RED];
+ fb_info->green = def_rgb565[GREEN];
+ fb_info->blue = def_rgb565[BLUE];
+ fb_info->transp = def_rgb565[TRANSP];
+ break;
+ case 24:
+ con1 |= BPPMODE(13);
+ con5 |= BPP24BL; /* FIXME */
+ fb_info->red = def_rgb888[RED];
+ fb_info->green = def_rgb888[GREEN];
+ fb_info->blue = def_rgb888[BLUE];
+ fb_info->transp = def_rgb888[TRANSP];
+ break;
+ default:
+ pr_err("Invalid bits per pixel value: %u\n", fb_info->bits_per_pixel);
+ return -EINVAL;
+ }
+
+ /* 'normal' in register description means positive logic */
+ if (!(mode->sync & FB_SYNC_HOR_HIGH_ACT))
+ con5 |= INV_HS;
+ if (!(mode->sync & FB_SYNC_VERT_HIGH_ACT))
+ con5 |= INV_VS;
+ if (!(mode->sync & FB_SYNC_DE_HIGH_ACT))
+ con5 |= INV_DE;
+ if (mode->sync & FB_SYNC_CLK_INVERT)
+ con5 |= INV_CLK; /* display should latch at the rising edge */
+ if (mode->sync & FB_SYNC_SWAP_RGB)
+ con5 |= HWSWP;
+
+ /* TODO power enable config via platform data */
+
+ /* vertical timing */
+ con2 = SET_VBPD(mode->upper_margin - 1) |
+ SET_LINEVAL(mode->yres - 1) |
+ SET_VFPD(mode->lower_margin - 1) |
+ SET_VSPW(mode->vsync_len - 1);
+
+ /* horizontal timing */
+ con3 = SET_HBPD(mode->left_margin - 1) |
+ SET_HOZVAL(mode->xres - 1) |
+ SET_HFPD(mode->right_margin - 1);
+ con4 = SET_HSPW(mode->hsync_len - 1);
+
+ /* basic timing setup */
+ writel(con1, fbh->base + LCDCON1);
+ pr_debug(" Writing %08X into %08X (con1)\n", con1, fbh->base + LCDCON1);
+ writel(con2, fbh->base + LCDCON2);
+ pr_debug(" Writing %08X into %08X (con2)\n", con2, fbh->base + LCDCON2);
+ writel(con3, fbh->base + LCDCON3);
+ pr_debug(" Writing %08X into %08X (con3)\n", con3, fbh->base + LCDCON3);
+ writel(con4, fbh->base + LCDCON4);
+ pr_debug(" Writing %08X into %08X (con4)\n", con4, fbh->base + LCDCON4);
+ writel(con5, fbh->base + LCDCON5);
+ pr_debug(" Writing %08X into %08X (con5)\n", con5, fbh->base + LCDCON5);
+
+ pr_debug("Setting up the fb baseadress to %08X\n", fb_info->fb_dev->map_base);
+
+ /* framebuffer memory setup */
+ writel(fb_info->fb_dev->map_base >> 1, fbh->base + LCDSADDR1);
+ size = mode->xres * (fb_info->bits_per_pixel >> 3) * (mode->yres);
+ writel(SET_LCDBASEL((fb_info->fb_dev->map_base + size) >> 1), fbh->base + LCDSADDR2);
+
+ writel(SET_OFFSIZE(0) |
+ SET_PAGE_WIDTH((mode->xres * fb_info->bits_per_pixel) >> 4),
+ fbh->base + LCDSADDR3);
+
+ writel(FIWSEL, fbh->base + LCDINTMSK);
+
+ return 0;
+}
+
+/**
+ * Print some information about the current hardware state
+ * @param hw_dev S3C video device
+ */
+#ifdef CONFIG_VIDEO_INFO_VERBOSE
+static void s3cfb_info(struct device_d *hw_dev)
+{
+ uint32_t con1, con2, con3, con4, con5, addr1, addr2, addr3;
+
+ con1 = readl(hw_dev->map_base + LCDCON1);
+ addr1 = readl(hw_dev->map_base + LCDSADDR1);
+ addr2 = readl(hw_dev->map_base + LCDSADDR2);
+ addr3 = readl(hw_dev->map_base + LCDSADDR3);
+
+ printf(" Video hardware info:\n");
+ printf(" Video clock is running at %u Hz\n", s3c24xx_get_hclk() / ((GET_CLKVAL(con1) + 1) * 2));
+ printf(" Video memory bank starts at 0x%08X\n", GET_LCDBANK(addr1) << 22);
+ printf(" Video memory bank offset: 0x%08X\n", GET_LCDBASEU(addr1));
+ printf(" Video memory end: 0x%08X\n", GET_LCDBASEU(addr2));
+ printf(" Virtual screen offset size: %u half words\n", GET_OFFSIZE(addr3));
+ printf(" Virtual screen page width: %u half words\n", GET_PAGE_WIDTH(addr3));
+}
+#endif
+
+/*
+ * There is only one video hardware instance available.
+ * It makes no sense to dynamically allocate this data
+ */
+static struct s3cfb_host host_data = {
+ .fb_data.fb_mode = s3cfb_initialize_mode,
+ .fb_data.fb_enable = s3cfb_enable_controller,
+ .fb_data.fb_disable = s3cfb_disable_controller,
+};
+
+static int s3cfb_probe(struct device_d *hw_dev)
+{
+ struct s3c_fb_platform_data *pdata = hw_dev->platform_data;
+ struct device_d *fb_dev;
+
+ pr_debug("%s called\n", __func__);
+
+ if (pdata == NULL) {
+ pr_debug("Framebuffer driver missing platform data");
+ return -ENODEV;
+ }
+
+ /* enable unit's clock */
+ s3c244x_mod_clock(CLK_LCDC, 1);
+
+ writel(0, hw_dev->map_base + LCDCON1);
+ /* off may be means high level */
+ writel(0, hw_dev->map_base + LCDCON5);
+
+ /* disable it again until user request */
+ s3c244x_mod_clock(CLK_LCDC, 0);
+
+ /* add runtime hardware info */
+ host_data.hw_dev = hw_dev;
+ host_data.base = (void*)hw_dev->map_base;
+
+ /* add runtime video info */
+ host_data.fb_data.mode = pdata->mode_list;
+ host_data.fb_data.mode_cnt = pdata->mode_cnt;
+
+ fb_dev = register_framebuffer(&host_data.fb_data, pdata->framebuffer, pdata->size);
+ if (fb_dev == NULL) {
+ pr_err("Failed to register framebuffer\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static struct driver_d s3cfb_driver = {
+ .name = "s3cfb",
+ .probe = s3cfb_probe,
+#ifdef CONFIG_VIDEO_INFO_VERBOSE
+ .info = s3cfb_info,
+#endif
+};
+
+static int s3cfb_init(void)
+{
+ return register_driver(&s3cfb_driver);
+}
+
+device_initcall(s3cfb_init);
+
+/**
+ * The S3C244x LCD controller supports passive (CSTN/STN) and active (TFT) LC displays
+ *
+ * The driver itself currently supports only active TFT LC displays in the follwing manner:
+ *
+ * * Palletized colours
+ * - 1 bpp
+ * - 2 bpp
+ * - 4 bpp
+ * - 8 bpp
+ * * True colours
+ * - 16 bpp
+ * - 24 bpp
+ */
--
1.7.2.3
[-- Attachment #2: Type: text/plain, Size: 149 bytes --]
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 08/11] Add a video driver for S3C2440 bases platforms
2010-10-22 16:53 ` [PATCH 08/11] Add a video driver for S3C2440 bases platforms Juergen Beisert
@ 2010-10-22 18:56 ` Sascha Hauer
2010-10-23 10:37 ` Juergen Beisert
0 siblings, 1 reply; 23+ messages in thread
From: Sascha Hauer @ 2010-10-22 18:56 UTC (permalink / raw)
To: Juergen Beisert; +Cc: barebox, Juergen Beisert
On Fri, Oct 22, 2010 at 06:53:22PM +0200, Juergen Beisert wrote:
> From: Juergen Beisert <juergen@kreuzholzen.de>
>
> Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
> ---
> arch/arm/mach-s3c24xx/include/mach/fb.h | 40 +++
> drivers/video/Kconfig | 6 +
> drivers/video/Makefile | 1 +
> drivers/video/s3c.c | 454 +++++++++++++++++++++++++++++++
> 4 files changed, 501 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/mach-s3c24xx/include/mach/fb.h
> create mode 100644 drivers/video/s3c.c
>
> diff --git a/drivers/video/s3c.c b/drivers/video/s3c.c
> new file mode 100644
> index 0000000..cd0f220
> --- /dev/null
> +++ b/drivers/video/s3c.c
> +
> +/**
> + * Prepare the video hardware for a specified video mode
> + * @param fb_info Framebuffer information
> + * @param mode The video mode description to initialize
> + * @return 0 on success
> + *
> + * FIXME Diese Routine darf die Pinx nach drau?en nicht aktivieren. Zur Zeit macht sie das!
You should at least translate this to english ;)
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread
* Re: [PATCH 08/11] Add a video driver for S3C2440 bases platforms
2010-10-22 18:56 ` Sascha Hauer
@ 2010-10-23 10:37 ` Juergen Beisert
0 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-23 10:37 UTC (permalink / raw)
To: barebox
Sascha Hauer wrote:
> On Fri, Oct 22, 2010 at 06:53:22PM +0200, Juergen Beisert wrote:
> > From: Juergen Beisert <juergen@kreuzholzen.de>
> >
> > Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
> > ---
> > arch/arm/mach-s3c24xx/include/mach/fb.h | 40 +++
> > drivers/video/Kconfig | 6 +
> > drivers/video/Makefile | 1 +
> > drivers/video/s3c.c | 454
> > +++++++++++++++++++++++++++++++ 4 files changed, 501 insertions(+), 0
> > deletions(-)
> > create mode 100644 arch/arm/mach-s3c24xx/include/mach/fb.h
> > create mode 100644 drivers/video/s3c.c
> >
> > diff --git a/drivers/video/s3c.c b/drivers/video/s3c.c
> > new file mode 100644
> > index 0000000..cd0f220
> > --- /dev/null
> > +++ b/drivers/video/s3c.c
> > +
> > +/**
> > + * Prepare the video hardware for a specified video mode
> > + * @param fb_info Framebuffer information
> > + * @param mode The video mode description to initialize
> > + * @return 0 on success
> > + *
> > + * FIXME Diese Routine darf die Pinx nach drau?en nicht aktivieren. Zur
> > Zeit macht sie das!
>
> You should at least translate this to english ;)
Sure, I already removed this sentence in my local patch stack... :-)
jbe
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | Phone: +49-8766-939 228 |
Vertretung Sued/Muenchen, Germany | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de/ |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 09/11] STM378x: Add video driver for this platform
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
` (7 preceding siblings ...)
2010-10-22 16:53 ` [PATCH 08/11] Add a video driver for S3C2440 bases platforms Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 18:59 ` Sascha Hauer
2010-10-22 16:53 ` [PATCH 10/11] Remove variable size restrictions Juergen Beisert
2010-10-22 16:53 ` [PATCH 11/11] Add doxygen documentation to the framebfuffer code Juergen Beisert
10 siblings, 1 reply; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
As there is currently no user of this driver (but coming soon) it is for
reference only.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
arch/arm/mach-stm/include/mach/fb.h | 38 +++
drivers/video/Kconfig | 7 +
drivers/video/Makefile | 1 +
drivers/video/stm.c | 556 +++++++++++++++++++++++++++++++++++
4 files changed, 602 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-stm/include/mach/fb.h
create mode 100644 drivers/video/stm.c
diff --git a/arch/arm/mach-stm/include/mach/fb.h b/arch/arm/mach-stm/include/mach/fb.h
new file mode 100644
index 0000000..6596ef2
--- /dev/null
+++ b/arch/arm/mach-stm/include/mach/fb.h
@@ -0,0 +1,38 @@
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#ifndef __MACH_FB_H
+# define __MACH_FB_H
+
+#include <fb.h>
+
+#define STMLCDIF_8BIT 1 /** pixel data bus to the display is of 8 bit width */
+#define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */
+#define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */
+#define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */
+
+struct imx_fb_videomode {
+ struct fb_videomode *mode_list;
+ unsigned mode_count;
+ void *framebuffer; /**< force fixed framebuffer address if != NULL */
+ unsigned size; /**< force fixed size if != NULL */
+
+ unsigned dotclk_delay; /**< refer manual HW_LCDIF_VDCTRL4 register */
+ unsigned ld_intf_width; /**< refer STMLCDIF_* macros */
+};
+
+#endif /* __MACH_FB_H */
+
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 64f68c4..63a80b0 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -55,4 +55,11 @@ config S3C_VIDEO
help
Add support for the S3C244x LCD controller.
+config DRIVER_VIDEO_STM
+ bool "i.MX23/28 framebuffer driver"
+ depends on ARCH_STM
+ help
+ Say 'Y' here to enable framebuffer and spash screen support for
+ i.MX23 and i.MX28 based systems.
+
endif
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 4287fc8..0ddb81e 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -1,5 +1,6 @@
obj-$(CONFIG_VIDEO) += fb.o
+obj-$(CONFIG_DRIVER_VIDEO_STM) += stm.o
obj-$(CONFIG_DRIVER_VIDEO_IMX) += imx.o
obj-$(CONFIG_DRIVER_VIDEO_IMX_IPU) += imx-ipu-fb.o
obj-$(CONFIG_S3C_VIDEO) += s3c.o
diff --git a/drivers/video/stm.c b/drivers/video/stm.c
new file mode 100644
index 0000000..b18378a
--- /dev/null
+++ b/drivers/video/stm.c
@@ -0,0 +1,556 @@
+/*
+ * Copyright (C) 2010 Juergen Beisert, Pengutronix
+ *
+ * This code is based on:
+ * Author: Vitaly Wool <vital@embeddedalley.com>
+ *
+ * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+/**
+ * @file
+ * @brief LCDIF driver for i.MX23 and i.MX28 (i.MX23 untested yet)
+ *
+ * The LCDIF support four modes of operation
+ * - MPU interface (to drive smart displays) -> not supported yet
+ * - VSYNC interface (like MPU interface plus Vsync) -> not supported yet
+ * - Dotclock interface (to drive LC displays with RGB data and sync signals)
+ * - DVI (to drive ITU-R BT656) -> not supported yet
+ *
+ * This driver depends on a correct setup of the pins used for this purpose
+ * (platform specific).
+ *
+ * For the developer: Don't forget to set the data bus width to the display
+ * in the imx_fb_videomode structure. You will else end up with ugly colours.
+ * If you fighting against jitter you can vary the clock delay. This is a feature
+ * of the i.MX28 and you can vary it between 2 ns ... 8 ns in 2 ns steps. Give
+ * the required value in the imx_fb_videomode structure.
+ */
+
+/* #define DEBUG */
+
+#include <common.h>
+#include <init.h>
+#include <driver.h>
+#include <malloc.h>
+#include <errno.h>
+#include <xfuncs.h>
+#include <asm/io.h>
+#include <mach/clock.h>
+#include <mach/fb.h>
+
+#define HW_LCDIF_CTRL 0x00
+# define CTRL_SFTRST (1 << 31)
+# define CTRL_CLKGATE (1 << 30)
+# define CTRL_BYPASS_COUNT (1 << 19)
+# define CTRL_VSYNC_MODE (1 << 18)
+# define CTRL_DOTCLK_MODE (1 << 17)
+# define CTRL_DATA_SELECT (1 << 16)
+# define SET_BUS_WIDTH(x) (((x) & 0x3) << 10)
+# define SET_WORD_LENGTH(x) (((x) & 0x3) << 8)
+# define GET_WORD_LENGTH(x) (((x) >> 8) & 0x3)
+# define CTRL_MASTER (1 << 5)
+# define CTRL_DF16 (1 << 3)
+# define CTRL_DF18 (1 << 2)
+# define CTRL_DF24 (1 << 1)
+# define CTRL_RUN (1 << 0)
+
+#define HW_LCDIF_CTRL1 0x10
+# define SET_BYTE_PACKAGING(x) (((x) & 0xf) << 16)
+# define GET_BYTE_PACKAGING(x) (((x) >> 16) & 0xf)
+
+#define HW_LCDIF_CTRL2 0x20
+
+#define HW_LCDIF_TRANSFER_COUNT 0x30
+# define SET_VCOUNT(x) (((x) & 0xffff) << 16)
+# define SET_HCOUNT(x) ((x) & 0xffff)
+
+#define HW_LCDIF_CUR_BUF 0x40
+
+#define HW_LCDIF_NEXT_BUF 0x50
+
+#define HW_LCDIF_TIMING 0x60
+# define SET_CMD_HOLD(x) (((x) & 0xff) << 24)
+# define SET_CMD_SETUP(x) (((x) & 0xff) << 16)
+# define SET_DATA_HOLD(x) (((x) & 0xff) << 8)
+# define SET_DATA_SETUP(x) ((x) & 0xff))
+
+#define HW_LCDIF_VDCTRL0 0x70
+# define VDCTRL0_ENABLE_PRESENT (1 << 28)
+# define VDCTRL0_VSYNC_POL (1 << 27) /* 0 = low active, 1 = high active */
+# define VDCTRL0_HSYNC_POL (1 << 26) /* 0 = low active, 1 = high active */
+# define VDCTRL0_DOTCLK_POL (1 << 25) /* 0 = output at falling edge, capturing at rising edge */
+# define VDCTRL0_ENABLE_POL (1 << 24) /* 0 = low active, 1 = high active */
+# define VDCTRL0_VSYNC_PERIOD_UNIT (1 << 21)
+# define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT (1 << 20)
+# define VDCTRL0_HALF_LINE (1 << 19)
+# define VDCTRL0_HALF_LINE_MODE (1 << 18)
+# define SET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff)
+
+#define HW_LCDIF_VDCTRL1 0x80
+
+#define HW_LCDIF_VDCTRL2 0x90
+# define SET_HSYNC_PULSE_WIDTH(x) (((x) & 0x3fff) << 18)
+# define SET_HSYNC_PERIOD(x) ((x) & 0x3ffff)
+
+#define HW_LCDIF_VDCTRL3 0xa0
+# define VDCTRL3_MUX_SYNC_SIGNALS (1 << 29)
+# define VDCTRL3_VSYNC_ONLY (1 << 28)
+# define SET_HOR_WAIT_CNT(x) (((x) & 0xfff) << 16)
+# define SET_VERT_WAIT_CNT(x) ((x) & 0xffff)
+
+#define HW_LCDIF_VDCTRL4 0xb0
+# define SET_DOTCLK_DLY(x) (((x) & 0x7) << 29)
+# define VDCTRL4_SYNC_SIGNALS_ON (1 << 18)
+# define SET_DOTCLK_H_VALID_DATA_CNT(x) ((x) & 0x3ffff)
+
+#define HW_LCDIF_DVICTRL0 0xc0
+#define HW_LCDIF_DVICTRL1 0xd0
+#define HW_LCDIF_DVICTRL2 0xe0
+#define HW_LCDIF_DVICTRL3 0xf0
+#define HW_LCDIF_DVICTRL4 0x100
+#define HW_LCDIF_DATA 0x180
+
+#define HW_LCDIF_DEBUG0 0x1d0
+# define DEBUG_HSYNC (1 < 26)
+# define DEBUG_VSYNC (1 < 25)
+
+#define RED 0
+#define GREEN 1
+#define BLUE 2
+#define TRANSP 3
+
+struct imxfb_host {
+ struct fb_host fb_data;
+ struct device_d *hw_dev;
+ void __iomem *base;
+};
+
+#define fb_info_to_imxfb_host(x) ((struct imxfb_host*)((x)->host))
+
+/* the RGB565 true colour mode */
+static const struct fb_bitfield def_rgb565[] = {
+ [RED] = {
+ .offset = 11,
+ .length = 5,
+ },
+ [GREEN] = {
+ .offset = 5,
+ .length = 6,
+ },
+ [BLUE] = {
+ .offset = 0,
+ .length = 5,
+ },
+ [TRANSP] = { /* no support for transparency */
+ .length = 0,
+ }
+};
+
+/* the RGB666 true colour mode */
+static const struct fb_bitfield def_rgb666[] = {
+ [RED] = {
+ .offset = 16,
+ .length = 6,
+ },
+ [GREEN] = {
+ .offset = 8,
+ .length = 6,
+ },
+ [BLUE] = {
+ .offset = 0,
+ .length = 6,
+ },
+ [TRANSP] = { /* no support for transparency */
+ .length = 0,
+ }
+};
+
+/* the RGB888 true colour mode */
+static const struct fb_bitfield def_rgb888[] = {
+ [RED] = {
+ .offset = 16,
+ .length = 8,
+ },
+ [GREEN] = {
+ .offset = 8,
+ .length = 8,
+ },
+ [BLUE] = {
+ .offset = 0,
+ .length = 8,
+ },
+ [TRANSP] = { /* no support for transparency */
+ .length = 0,
+ }
+};
+
+/**
+ * Just calculate the amount of required bytes per line
+ * @param ppl Used pixel per line
+ * @param bpp Bits per pixel
+ * @return Byte count
+ */
+static inline unsigned calc_line_length(unsigned ppl, unsigned bpp)
+{
+ return (ppl * bpp) >> 3;
+}
+
+/**
+ * Prepare the video hardware for a specified video mode
+ * @param fb_info Framebuffer information
+ * @param mode The video mode description to initialize
+ * @return 0 on success
+ *
+ * Dotclock mode:
+ * One line of pixels or one frame in the i.MX28 is defined to:
+ * @verbatim
+ * |<---------------------- one line period -------------------------------->|
+ * |<- HSync length ->|
+ * |<----- Start of line --->|
+ * |<-------- active line data ------>|
+ *
+ * |<------------------------ frame period --------------------------------->|
+ * |<- VSync length ->|
+ * |<--- Start of 1. line -->|
+ * |<---------- active lines -------->|
+ * @endverbatim
+ * Based on the values from struct fb_videomode:
+ * - "one line period" = left_margin + xres + right_margin + hsync_len
+ * - "HSync length" = hsync_len
+ * - "Start of line" = hsync_len + left_margin
+ * - "active line data" = xres
+ */
+static int stmfb_initialize_mode(struct fb_info *fb_info, const struct fb_videomode *mode)
+{
+ struct imxfb_host *fbh = fb_info_to_imxfb_host(fb_info);
+ struct imx_fb_videomode *pdata = fbh->hw_dev->platform_data;
+ uint32_t reg;
+ unsigned size;
+
+ pr_debug("%s called\n", __func__);
+ /*
+ * we need at least this amount of memory for the framebuffer
+ */
+ size = calc_line_length(mode->xres, fb_info->bits_per_pixel) * mode->yres;
+ if (fb_info->fb_dev->size != 0) {
+ if (size > fb_info->fb_dev->size) {
+ pr_err("Cannot initialize video mode '%s': Its too large. "
+ "Required bytes are %u, available only %u\n",
+ mode->name, size, fb_info->fb_dev->size);
+ return -EINVAL;
+ }
+ } else
+ fb_info->fb_dev->size = size;
+
+ /*
+ * if no framebuffer memory was specified yet, allocate one,
+ * and allocate more memory, on user request
+ */
+ if (fb_info->fb_dev->map_base == 0U)
+ fb_info->fb_dev->map_base = (resource_size_t)xzalloc(fb_info->fb_dev->size);
+
+ /* TODO HCLK must be active at this point of time! */
+
+ size = imx_set_lcdifclk(PICOS2KHZ(mode->pixclock));
+ if (size == 0) {
+ pr_debug("Unable to set a valid pixel clock\n");
+ return -EINVAL;
+ }
+
+ /*
+ * bring the controller out of reset and configure it into DOTCLOCK mode
+ */
+ reg = CTRL_BYPASS_COUNT | /* always in DOTCLOCK mode */
+ CTRL_DOTCLK_MODE;
+ writel(reg, fbh->base + HW_LCDIF_CTRL);
+
+ /* master mode only */
+ reg |= CTRL_MASTER;
+
+ /*
+ * Configure videomode and interface mode
+ */
+ reg |= SET_BUS_WIDTH(pdata->ld_intf_width);
+ switch (fb_info->bits_per_pixel) {
+ case 8:
+ reg |= SET_WORD_LENGTH(1);
+ /* TODO refer manual page 2046 */
+ pr_warning("8 bpp mode not supported yet\n");
+ break;
+ case 16:
+ pr_debug("Setting up an RGB565 mode\n");
+ reg |= SET_WORD_LENGTH(0) | CTRL_DF16; /* we assume RGB565 */
+ writel(SET_BYTE_PACKAGING(0xf), fbh->base + HW_LCDIF_CTRL1);
+ fb_info->red = def_rgb565[RED];
+ fb_info->green = def_rgb565[GREEN];
+ fb_info->blue = def_rgb565[BLUE];
+ fb_info->transp = def_rgb565[TRANSP];
+ break;
+ case 24:
+ case 32:
+ pr_debug("Setting up an RGB888/666 mode\n");
+ reg |= SET_WORD_LENGTH(3);
+ switch (pdata->ld_intf_width) {
+ case STMLCDIF_8BIT:
+ pr_debug("Unsupported LCD bus width mapping\n");
+ break;
+ case STMLCDIF_16BIT:
+ case STMLCDIF_18BIT:
+ /* 24 bit to 18 bit mapping */
+ reg |= CTRL_DF24; /* ignore the upper 2 bits in each colour component */
+ fb_info->red = def_rgb666[RED];
+ fb_info->green = def_rgb666[GREEN];
+ fb_info->blue = def_rgb666[BLUE];
+ fb_info->transp = def_rgb666[TRANSP];
+ break;
+ case STMLCDIF_24BIT:
+ /* real 24 bit */
+ fb_info->red = def_rgb888[RED];
+ fb_info->green = def_rgb888[GREEN];
+ fb_info->blue = def_rgb888[BLUE];
+ fb_info->transp = def_rgb888[TRANSP];
+ break;
+ }
+ /* do not use packed pixels = one pixel per word instead */
+ writel(SET_BYTE_PACKAGING(0x7), fbh->base + HW_LCDIF_CTRL1);
+ break;
+ default:
+ pr_debug("Unhandled colour depth of %u\n", fb_info->bits_per_pixel);
+ return -EINVAL;
+ }
+ writel(reg, fbh->base + HW_LCDIF_CTRL);
+ pr_debug("Setting up CTRL to %08X\n", reg);
+
+ writel(SET_VCOUNT(mode->yres) |
+ SET_HCOUNT(mode->xres), fbh->base + HW_LCDIF_TRANSFER_COUNT);
+
+ reg = VDCTRL0_ENABLE_PRESENT | /* always in DOTCLOCK mode */
+ VDCTRL0_VSYNC_PERIOD_UNIT |
+ VDCTRL0_VSYNC_PULSE_WIDTH_UNIT;
+ if (mode->sync & FB_SYNC_HOR_HIGH_ACT)
+ reg |= VDCTRL0_HSYNC_POL;
+ if (mode->sync & FB_SYNC_VERT_HIGH_ACT)
+ reg |= VDCTRL0_VSYNC_POL;
+ if (mode->sync & FB_SYNC_DE_HIGH_ACT)
+ reg |= VDCTRL0_ENABLE_POL;
+ if (mode->sync & FB_SYNC_CLK_INVERT)
+ reg |= VDCTRL0_DOTCLK_POL;
+
+ reg |= SET_VSYNC_PULSE_WIDTH(mode->vsync_len);
+ writel(reg, fbh->base + HW_LCDIF_VDCTRL0);
+ pr_debug("Setting up VDCTRL0 to %08X\n", reg);
+
+ /* frame length in lines */
+ writel(mode->upper_margin + mode->vsync_len + mode->lower_margin + mode->yres,
+ fbh->base + HW_LCDIF_VDCTRL1);
+
+ /* line length in units of clocks or pixels */
+ writel(SET_HSYNC_PULSE_WIDTH(mode->hsync_len) |
+ SET_HSYNC_PERIOD(mode->left_margin + mode->hsync_len + mode->right_margin + mode->xres),
+ fbh->base + HW_LCDIF_VDCTRL2);
+
+ writel(SET_HOR_WAIT_CNT(mode->left_margin + mode->hsync_len) |
+ SET_VERT_WAIT_CNT(mode->upper_margin + mode->vsync_len),
+ fbh->base + HW_LCDIF_VDCTRL3);
+
+ writel(SET_DOTCLK_DLY(pdata->dotclk_delay) |
+ SET_DOTCLK_H_VALID_DATA_CNT(mode->xres),
+ fbh->base + HW_LCDIF_VDCTRL4);
+
+ writel(fb_info->fb_dev->map_base, fbh->base + HW_LCDIF_CUR_BUF);
+ /* always show one framebuffer only */
+ writel(fb_info->fb_dev->map_base, fbh->base + HW_LCDIF_NEXT_BUF);
+
+ return 0;
+}
+
+/**
+ * @param fb_info Framebuffer information
+ */
+static void stmfb_enable_controller(struct fb_info *fb_info)
+{
+ struct imxfb_host *fbh = fb_info_to_imxfb_host(fb_info);
+ uint32_t reg, last_reg;
+ unsigned loop, edges;
+
+ pr_debug("%s called\n", __func__);
+
+ /* if it was disabled, re-enable the mode again */
+ reg = readl(fbh->base + HW_LCDIF_CTRL);
+ reg |= CTRL_DOTCLK_MODE;
+ writel(reg, fbh->base + HW_LCDIF_CTRL);
+
+ /* enable the SYNC signals first, then the DMA enginge */
+ reg = readl(fbh->base + HW_LCDIF_VDCTRL4);
+ reg |= VDCTRL4_SYNC_SIGNALS_ON;
+ writel(reg, fbh->base + HW_LCDIF_VDCTRL4);
+
+ /*
+ * Give the attached LC display or monitor a chance to sync into
+ * our signals.
+ * Wait for at least 2 VSYNCs = four VSYNC edges
+ */
+ edges = 4;
+
+ while (edges != 0) {
+ loop = 800;
+ last_reg = readl(fbh->base + HW_LCDIF_DEBUG0) & DEBUG_VSYNC;
+ do {
+ reg = readl(fbh->base + HW_LCDIF_DEBUG0) & DEBUG_VSYNC;
+ if (reg != last_reg);
+ break;
+ last_reg = reg;
+ loop--;
+ } while (loop != 0);
+ edges--;
+ }
+
+ reg = readl(fbh->base + HW_LCDIF_CTRL);
+ reg |= CTRL_RUN;
+ writel(reg, fbh->base + HW_LCDIF_CTRL);
+}
+
+/**
+ * @param fb_info Framebuffer information
+ */
+static void stmfb_disable_controller(struct fb_info *fb_info)
+{
+ struct imxfb_host *fbh = fb_info_to_imxfb_host(fb_info);
+ unsigned loop;
+ uint32_t reg;
+
+ pr_debug("%s called\n", __func__);
+ /*
+ * Even if we disable the controller here, it will still continue
+ * until its FIFOs are running out of data
+ */
+ reg = readl(fbh->base + HW_LCDIF_CTRL);
+ reg &= ~CTRL_DOTCLK_MODE;
+ writel(reg, fbh->base + HW_LCDIF_CTRL);
+
+ loop = 1000;
+ while (loop) {
+ reg = readl(fbh->base + HW_LCDIF_CTRL);
+ if (!(reg & CTRL_RUN))
+ break;
+ loop--;
+ }
+
+ reg = readl(fbh->base + HW_LCDIF_VDCTRL4);
+ reg &= ~VDCTRL4_SYNC_SIGNALS_ON;
+ writel(reg, fbh->base + HW_LCDIF_VDCTRL4);
+}
+
+/**
+ * Print some information about the current hardware state
+ * @param hw_dev STM video device
+ */
+static void stmfb_info(struct device_d *hw_dev)
+{
+ uint32_t reg;
+
+ printf(" STM video hardware:\n");
+ printf(" Pixel clock: %u kHz\n", imx_get_lcdifclk());
+
+ reg = readl(hw_dev->map_base + HW_LCDIF_CTRL);
+ switch (GET_WORD_LENGTH(reg)) {
+ case 0:
+ printf(" 16 bpp mode with %s colour scheme\n", reg & CTRL_DF16 ? "RGB565" : "ARGB1555");
+ switch (GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1))) {
+ case 0xf:
+ printf(" One pixel per halfword\n");
+ break;
+ case 0x3:
+ printf(" One pixel per word\n");
+ break;
+ default:
+ printf("Unknown pixel packaging: %u\n", GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1)));
+ }
+ break;
+ case 1:
+ case 2:
+ printf("Unsupported bpp mode yet!\n");
+ break;
+ case 3:
+ printf(" 24 bpp mode with %s colour scheme\n", reg & CTRL_DF24 ? "RGB888" : "RGB666");
+ switch (GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1))) {
+ case 0x7:
+ printf(" One pixel per word (xRGB xRGB xRGB ...)\n");
+ break;
+ case 0xf:
+ printf("Packed pixel format per word (RGBR GBRG BRGB ...)\n");
+ break;
+ default:
+ printf("Unknown pixel packaging: %u\n", GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1)));
+ }
+ break;
+ }
+}
+
+/*
+ * There is only one video hardware instance available.
+ * It makes no sense to dynamically allocate this data
+ */
+static struct imxfb_host host_data = {
+ .fb_data.fb_mode = stmfb_initialize_mode,
+ .fb_data.fb_enable = stmfb_enable_controller,
+ .fb_data.fb_disable = stmfb_disable_controller,
+ .fb_data.bits_per_pixel = 16,
+};
+
+static int stmfb_probe(struct device_d *hw_dev)
+{
+ struct imx_fb_videomode *pdata = hw_dev->platform_data;
+ struct device_d *fb_dev;
+
+ if (pdata == NULL) {
+ pr_debug("STMFB: No platformdata. Giving up\n");
+ return -ENODEV;
+ }
+
+ /* add runtime hardware info */
+ host_data.hw_dev = hw_dev;
+ host_data.base = (void*)hw_dev->map_base;
+
+ /* add runtime video info */
+ host_data.fb_data.mode = pdata->mode_list;
+ host_data.fb_data.mode_cnt = pdata->mode_count;
+
+ fb_dev = register_framebuffer(&host_data.fb_data, pdata->framebuffer, pdata->size);
+ if (fb_dev == NULL) {
+ pr_err("STMFB: Failed to register framebuffer\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static struct driver_d stmfb_driver = {
+ .name = "stmfb",
+ .probe = stmfb_probe,
+ .info = stmfb_info,
+};
+
+static int stmfb_init(void)
+{
+ return register_driver(&stmfb_driver);
+}
+
+device_initcall(stmfb_init);
+
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 09/11] STM378x: Add video driver for this platform
2010-10-22 16:53 ` [PATCH 09/11] STM378x: Add video driver for this platform Juergen Beisert
@ 2010-10-22 18:59 ` Sascha Hauer
2010-10-23 10:40 ` Juergen Beisert
0 siblings, 1 reply; 23+ messages in thread
From: Sascha Hauer @ 2010-10-22 18:59 UTC (permalink / raw)
To: Juergen Beisert; +Cc: barebox
On Fri, Oct 22, 2010 at 06:53:23PM +0200, Juergen Beisert wrote:
> As there is currently no user of this driver (but coming soon) it is for
> reference only.
>
> Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
> ---
> arch/arm/mach-stm/include/mach/fb.h | 38 +++
> drivers/video/Kconfig | 7 +
> drivers/video/Makefile | 1 +
> drivers/video/stm.c | 556 +++++++++++++++++++++++++++++++++++
> 4 files changed, 602 insertions(+), 0 deletions(-)
> create mode 100644 arch/arm/mach-stm/include/mach/fb.h
> create mode 100644 drivers/video/stm.c
>
> diff --git a/arch/arm/mach-stm/include/mach/fb.h b/arch/arm/mach-stm/include/mach/fb.h
> new file mode 100644
> index 0000000..6596ef2
> --- /dev/null
> +++ b/arch/arm/mach-stm/include/mach/fb.h
> @@ -0,0 +1,38 @@
> +/*
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; either version 2
> + * of the License, or (at your option) any later version.
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301, USA.
> + */
> +
> +#ifndef __MACH_FB_H
> +# define __MACH_FB_H
> +
> +#include <fb.h>
> +
> +#define STMLCDIF_8BIT 1 /** pixel data bus to the display is of 8 bit width */
> +#define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */
> +#define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */
> +#define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */
> +
> +struct imx_fb_videomode {
> + struct fb_videomode *mode_list;
> + unsigned mode_count;
> + void *framebuffer; /**< force fixed framebuffer address if != NULL */
> + unsigned size; /**< force fixed size if != NULL */
> +
> + unsigned dotclk_delay; /**< refer manual HW_LCDIF_VDCTRL4 register */
> + unsigned ld_intf_width; /**< refer STMLCDIF_* macros */
> +};
> +
> +#endif /* __MACH_FB_H */
> +
> diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
> index 64f68c4..63a80b0 100644
> --- a/drivers/video/Kconfig
> +++ b/drivers/video/Kconfig
> @@ -55,4 +55,11 @@ config S3C_VIDEO
> help
> Add support for the S3C244x LCD controller.
>
> +config DRIVER_VIDEO_STM
> + bool "i.MX23/28 framebuffer driver"
> + depends on ARCH_STM
> + help
> + Say 'Y' here to enable framebuffer and spash screen support for
> + i.MX23 and i.MX28 based systems.
> +
> endif
> diff --git a/drivers/video/Makefile b/drivers/video/Makefile
> index 4287fc8..0ddb81e 100644
> --- a/drivers/video/Makefile
> +++ b/drivers/video/Makefile
> @@ -1,5 +1,6 @@
> obj-$(CONFIG_VIDEO) += fb.o
>
> +obj-$(CONFIG_DRIVER_VIDEO_STM) += stm.o
> obj-$(CONFIG_DRIVER_VIDEO_IMX) += imx.o
> obj-$(CONFIG_DRIVER_VIDEO_IMX_IPU) += imx-ipu-fb.o
> obj-$(CONFIG_S3C_VIDEO) += s3c.o
> diff --git a/drivers/video/stm.c b/drivers/video/stm.c
> new file mode 100644
> index 0000000..b18378a
> --- /dev/null
> +++ b/drivers/video/stm.c
> @@ -0,0 +1,556 @@
> +/*
> + * Copyright (C) 2010 Juergen Beisert, Pengutronix
> + *
> + * This code is based on:
> + * Author: Vitaly Wool <vital@embeddedalley.com>
> + *
> + * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved.
> + * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * as published by the Free Software Foundation; either version 2
> + * of the License, or (at your option) any later version.
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301, USA.
> + */
> +
> +/**
> + * @file
> + * @brief LCDIF driver for i.MX23 and i.MX28 (i.MX23 untested yet)
> + *
> + * The LCDIF support four modes of operation
> + * - MPU interface (to drive smart displays) -> not supported yet
> + * - VSYNC interface (like MPU interface plus Vsync) -> not supported yet
> + * - Dotclock interface (to drive LC displays with RGB data and sync signals)
> + * - DVI (to drive ITU-R BT656) -> not supported yet
> + *
> + * This driver depends on a correct setup of the pins used for this purpose
> + * (platform specific).
> + *
> + * For the developer: Don't forget to set the data bus width to the display
> + * in the imx_fb_videomode structure. You will else end up with ugly colours.
> + * If you fighting against jitter you can vary the clock delay. This is a feature
> + * of the i.MX28 and you can vary it between 2 ns ... 8 ns in 2 ns steps. Give
> + * the required value in the imx_fb_videomode structure.
> + */
> +
> +/* #define DEBUG */
> +
> +#include <common.h>
> +#include <init.h>
> +#include <driver.h>
> +#include <malloc.h>
> +#include <errno.h>
> +#include <xfuncs.h>
> +#include <asm/io.h>
> +#include <mach/clock.h>
> +#include <mach/fb.h>
> +
> +#define HW_LCDIF_CTRL 0x00
> +# define CTRL_SFTRST (1 << 31)
> +# define CTRL_CLKGATE (1 << 30)
> +# define CTRL_BYPASS_COUNT (1 << 19)
> +# define CTRL_VSYNC_MODE (1 << 18)
> +# define CTRL_DOTCLK_MODE (1 << 17)
> +# define CTRL_DATA_SELECT (1 << 16)
> +# define SET_BUS_WIDTH(x) (((x) & 0x3) << 10)
> +# define SET_WORD_LENGTH(x) (((x) & 0x3) << 8)
> +# define GET_WORD_LENGTH(x) (((x) >> 8) & 0x3)
> +# define CTRL_MASTER (1 << 5)
> +# define CTRL_DF16 (1 << 3)
> +# define CTRL_DF18 (1 << 2)
> +# define CTRL_DF24 (1 << 1)
> +# define CTRL_RUN (1 << 0)
> +
> +#define HW_LCDIF_CTRL1 0x10
> +# define SET_BYTE_PACKAGING(x) (((x) & 0xf) << 16)
> +# define GET_BYTE_PACKAGING(x) (((x) >> 16) & 0xf)
> +
> +#define HW_LCDIF_CTRL2 0x20
> +
> +#define HW_LCDIF_TRANSFER_COUNT 0x30
> +# define SET_VCOUNT(x) (((x) & 0xffff) << 16)
> +# define SET_HCOUNT(x) ((x) & 0xffff)
> +
> +#define HW_LCDIF_CUR_BUF 0x40
> +
> +#define HW_LCDIF_NEXT_BUF 0x50
> +
> +#define HW_LCDIF_TIMING 0x60
> +# define SET_CMD_HOLD(x) (((x) & 0xff) << 24)
> +# define SET_CMD_SETUP(x) (((x) & 0xff) << 16)
> +# define SET_DATA_HOLD(x) (((x) & 0xff) << 8)
> +# define SET_DATA_SETUP(x) ((x) & 0xff))
> +
> +#define HW_LCDIF_VDCTRL0 0x70
> +# define VDCTRL0_ENABLE_PRESENT (1 << 28)
> +# define VDCTRL0_VSYNC_POL (1 << 27) /* 0 = low active, 1 = high active */
> +# define VDCTRL0_HSYNC_POL (1 << 26) /* 0 = low active, 1 = high active */
> +# define VDCTRL0_DOTCLK_POL (1 << 25) /* 0 = output at falling edge, capturing at rising edge */
> +# define VDCTRL0_ENABLE_POL (1 << 24) /* 0 = low active, 1 = high active */
> +# define VDCTRL0_VSYNC_PERIOD_UNIT (1 << 21)
> +# define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT (1 << 20)
> +# define VDCTRL0_HALF_LINE (1 << 19)
> +# define VDCTRL0_HALF_LINE_MODE (1 << 18)
> +# define SET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff)
> +
> +#define HW_LCDIF_VDCTRL1 0x80
> +
> +#define HW_LCDIF_VDCTRL2 0x90
> +# define SET_HSYNC_PULSE_WIDTH(x) (((x) & 0x3fff) << 18)
> +# define SET_HSYNC_PERIOD(x) ((x) & 0x3ffff)
> +
> +#define HW_LCDIF_VDCTRL3 0xa0
> +# define VDCTRL3_MUX_SYNC_SIGNALS (1 << 29)
> +# define VDCTRL3_VSYNC_ONLY (1 << 28)
> +# define SET_HOR_WAIT_CNT(x) (((x) & 0xfff) << 16)
> +# define SET_VERT_WAIT_CNT(x) ((x) & 0xffff)
> +
> +#define HW_LCDIF_VDCTRL4 0xb0
> +# define SET_DOTCLK_DLY(x) (((x) & 0x7) << 29)
> +# define VDCTRL4_SYNC_SIGNALS_ON (1 << 18)
> +# define SET_DOTCLK_H_VALID_DATA_CNT(x) ((x) & 0x3ffff)
> +
> +#define HW_LCDIF_DVICTRL0 0xc0
> +#define HW_LCDIF_DVICTRL1 0xd0
> +#define HW_LCDIF_DVICTRL2 0xe0
> +#define HW_LCDIF_DVICTRL3 0xf0
> +#define HW_LCDIF_DVICTRL4 0x100
> +#define HW_LCDIF_DATA 0x180
> +
> +#define HW_LCDIF_DEBUG0 0x1d0
> +# define DEBUG_HSYNC (1 < 26)
> +# define DEBUG_VSYNC (1 < 25)
> +
> +#define RED 0
> +#define GREEN 1
> +#define BLUE 2
> +#define TRANSP 3
> +
> +struct imxfb_host {
> + struct fb_host fb_data;
> + struct device_d *hw_dev;
> + void __iomem *base;
> +};
> +
> +#define fb_info_to_imxfb_host(x) ((struct imxfb_host*)((x)->host))
> +
> +/* the RGB565 true colour mode */
> +static const struct fb_bitfield def_rgb565[] = {
> + [RED] = {
> + .offset = 11,
> + .length = 5,
> + },
> + [GREEN] = {
> + .offset = 5,
> + .length = 6,
> + },
> + [BLUE] = {
> + .offset = 0,
> + .length = 5,
> + },
> + [TRANSP] = { /* no support for transparency */
> + .length = 0,
> + }
> +};
> +
> +/* the RGB666 true colour mode */
> +static const struct fb_bitfield def_rgb666[] = {
> + [RED] = {
> + .offset = 16,
> + .length = 6,
> + },
> + [GREEN] = {
> + .offset = 8,
> + .length = 6,
> + },
> + [BLUE] = {
> + .offset = 0,
> + .length = 6,
> + },
> + [TRANSP] = { /* no support for transparency */
> + .length = 0,
> + }
> +};
> +
> +/* the RGB888 true colour mode */
> +static const struct fb_bitfield def_rgb888[] = {
> + [RED] = {
> + .offset = 16,
> + .length = 8,
> + },
> + [GREEN] = {
> + .offset = 8,
> + .length = 8,
> + },
> + [BLUE] = {
> + .offset = 0,
> + .length = 8,
> + },
> + [TRANSP] = { /* no support for transparency */
> + .length = 0,
> + }
> +};
> +
> +/**
> + * Just calculate the amount of required bytes per line
> + * @param ppl Used pixel per line
> + * @param bpp Bits per pixel
> + * @return Byte count
> + */
> +static inline unsigned calc_line_length(unsigned ppl, unsigned bpp)
> +{
> + return (ppl * bpp) >> 3;
> +}
> +
> +/**
> + * Prepare the video hardware for a specified video mode
> + * @param fb_info Framebuffer information
> + * @param mode The video mode description to initialize
> + * @return 0 on success
> + *
> + * Dotclock mode:
> + * One line of pixels or one frame in the i.MX28 is defined to:
> + * @verbatim
> + * |<---------------------- one line period -------------------------------->|
> + * |<- HSync length ->|
> + * |<----- Start of line --->|
> + * |<-------- active line data ------>|
> + *
> + * |<------------------------ frame period --------------------------------->|
> + * |<- VSync length ->|
> + * |<--- Start of 1. line -->|
> + * |<---------- active lines -------->|
> + * @endverbatim
> + * Based on the values from struct fb_videomode:
> + * - "one line period" = left_margin + xres + right_margin + hsync_len
> + * - "HSync length" = hsync_len
> + * - "Start of line" = hsync_len + left_margin
> + * - "active line data" = xres
> + */
> +static int stmfb_initialize_mode(struct fb_info *fb_info, const struct fb_videomode *mode)
> +{
> + struct imxfb_host *fbh = fb_info_to_imxfb_host(fb_info);
> + struct imx_fb_videomode *pdata = fbh->hw_dev->platform_data;
> + uint32_t reg;
> + unsigned size;
> +
> + pr_debug("%s called\n", __func__);
> + /*
> + * we need at least this amount of memory for the framebuffer
> + */
> + size = calc_line_length(mode->xres, fb_info->bits_per_pixel) * mode->yres;
> + if (fb_info->fb_dev->size != 0) {
> + if (size > fb_info->fb_dev->size) {
> + pr_err("Cannot initialize video mode '%s': Its too large. "
> + "Required bytes are %u, available only %u\n",
> + mode->name, size, fb_info->fb_dev->size);
> + return -EINVAL;
> + }
> + } else
> + fb_info->fb_dev->size = size;
> +
> + /*
> + * if no framebuffer memory was specified yet, allocate one,
> + * and allocate more memory, on user request
> + */
> + if (fb_info->fb_dev->map_base == 0U)
> + fb_info->fb_dev->map_base = (resource_size_t)xzalloc(fb_info->fb_dev->size);
> +
> + /* TODO HCLK must be active at this point of time! */
> +
> + size = imx_set_lcdifclk(PICOS2KHZ(mode->pixclock));
> + if (size == 0) {
> + pr_debug("Unable to set a valid pixel clock\n");
> + return -EINVAL;
> + }
> +
> + /*
> + * bring the controller out of reset and configure it into DOTCLOCK mode
> + */
> + reg = CTRL_BYPASS_COUNT | /* always in DOTCLOCK mode */
> + CTRL_DOTCLK_MODE;
> + writel(reg, fbh->base + HW_LCDIF_CTRL);
> +
> + /* master mode only */
> + reg |= CTRL_MASTER;
> +
> + /*
> + * Configure videomode and interface mode
> + */
> + reg |= SET_BUS_WIDTH(pdata->ld_intf_width);
> + switch (fb_info->bits_per_pixel) {
> + case 8:
> + reg |= SET_WORD_LENGTH(1);
> + /* TODO refer manual page 2046 */
> + pr_warning("8 bpp mode not supported yet\n");
> + break;
> + case 16:
> + pr_debug("Setting up an RGB565 mode\n");
> + reg |= SET_WORD_LENGTH(0) | CTRL_DF16; /* we assume RGB565 */
> + writel(SET_BYTE_PACKAGING(0xf), fbh->base + HW_LCDIF_CTRL1);
> + fb_info->red = def_rgb565[RED];
> + fb_info->green = def_rgb565[GREEN];
> + fb_info->blue = def_rgb565[BLUE];
> + fb_info->transp = def_rgb565[TRANSP];
> + break;
> + case 24:
> + case 32:
> + pr_debug("Setting up an RGB888/666 mode\n");
> + reg |= SET_WORD_LENGTH(3);
> + switch (pdata->ld_intf_width) {
> + case STMLCDIF_8BIT:
> + pr_debug("Unsupported LCD bus width mapping\n");
> + break;
> + case STMLCDIF_16BIT:
> + case STMLCDIF_18BIT:
> + /* 24 bit to 18 bit mapping */
> + reg |= CTRL_DF24; /* ignore the upper 2 bits in each colour component */
> + fb_info->red = def_rgb666[RED];
> + fb_info->green = def_rgb666[GREEN];
> + fb_info->blue = def_rgb666[BLUE];
> + fb_info->transp = def_rgb666[TRANSP];
> + break;
> + case STMLCDIF_24BIT:
> + /* real 24 bit */
> + fb_info->red = def_rgb888[RED];
> + fb_info->green = def_rgb888[GREEN];
> + fb_info->blue = def_rgb888[BLUE];
> + fb_info->transp = def_rgb888[TRANSP];
> + break;
> + }
> + /* do not use packed pixels = one pixel per word instead */
> + writel(SET_BYTE_PACKAGING(0x7), fbh->base + HW_LCDIF_CTRL1);
> + break;
> + default:
> + pr_debug("Unhandled colour depth of %u\n", fb_info->bits_per_pixel);
> + return -EINVAL;
> + }
> + writel(reg, fbh->base + HW_LCDIF_CTRL);
> + pr_debug("Setting up CTRL to %08X\n", reg);
> +
> + writel(SET_VCOUNT(mode->yres) |
> + SET_HCOUNT(mode->xres), fbh->base + HW_LCDIF_TRANSFER_COUNT);
> +
> + reg = VDCTRL0_ENABLE_PRESENT | /* always in DOTCLOCK mode */
> + VDCTRL0_VSYNC_PERIOD_UNIT |
> + VDCTRL0_VSYNC_PULSE_WIDTH_UNIT;
> + if (mode->sync & FB_SYNC_HOR_HIGH_ACT)
> + reg |= VDCTRL0_HSYNC_POL;
> + if (mode->sync & FB_SYNC_VERT_HIGH_ACT)
> + reg |= VDCTRL0_VSYNC_POL;
> + if (mode->sync & FB_SYNC_DE_HIGH_ACT)
> + reg |= VDCTRL0_ENABLE_POL;
> + if (mode->sync & FB_SYNC_CLK_INVERT)
> + reg |= VDCTRL0_DOTCLK_POL;
> +
> + reg |= SET_VSYNC_PULSE_WIDTH(mode->vsync_len);
> + writel(reg, fbh->base + HW_LCDIF_VDCTRL0);
> + pr_debug("Setting up VDCTRL0 to %08X\n", reg);
> +
> + /* frame length in lines */
> + writel(mode->upper_margin + mode->vsync_len + mode->lower_margin + mode->yres,
> + fbh->base + HW_LCDIF_VDCTRL1);
> +
> + /* line length in units of clocks or pixels */
> + writel(SET_HSYNC_PULSE_WIDTH(mode->hsync_len) |
> + SET_HSYNC_PERIOD(mode->left_margin + mode->hsync_len + mode->right_margin + mode->xres),
> + fbh->base + HW_LCDIF_VDCTRL2);
> +
> + writel(SET_HOR_WAIT_CNT(mode->left_margin + mode->hsync_len) |
> + SET_VERT_WAIT_CNT(mode->upper_margin + mode->vsync_len),
> + fbh->base + HW_LCDIF_VDCTRL3);
> +
> + writel(SET_DOTCLK_DLY(pdata->dotclk_delay) |
> + SET_DOTCLK_H_VALID_DATA_CNT(mode->xres),
> + fbh->base + HW_LCDIF_VDCTRL4);
> +
> + writel(fb_info->fb_dev->map_base, fbh->base + HW_LCDIF_CUR_BUF);
> + /* always show one framebuffer only */
> + writel(fb_info->fb_dev->map_base, fbh->base + HW_LCDIF_NEXT_BUF);
> +
> + return 0;
> +}
> +
> +/**
> + * @param fb_info Framebuffer information
> + */
> +static void stmfb_enable_controller(struct fb_info *fb_info)
> +{
> + struct imxfb_host *fbh = fb_info_to_imxfb_host(fb_info);
> + uint32_t reg, last_reg;
> + unsigned loop, edges;
> +
> + pr_debug("%s called\n", __func__);
> +
> + /* if it was disabled, re-enable the mode again */
> + reg = readl(fbh->base + HW_LCDIF_CTRL);
> + reg |= CTRL_DOTCLK_MODE;
> + writel(reg, fbh->base + HW_LCDIF_CTRL);
> +
> + /* enable the SYNC signals first, then the DMA enginge */
> + reg = readl(fbh->base + HW_LCDIF_VDCTRL4);
> + reg |= VDCTRL4_SYNC_SIGNALS_ON;
> + writel(reg, fbh->base + HW_LCDIF_VDCTRL4);
> +
> + /*
> + * Give the attached LC display or monitor a chance to sync into
> + * our signals.
> + * Wait for at least 2 VSYNCs = four VSYNC edges
> + */
> + edges = 4;
> +
> + while (edges != 0) {
> + loop = 800;
> + last_reg = readl(fbh->base + HW_LCDIF_DEBUG0) & DEBUG_VSYNC;
> + do {
> + reg = readl(fbh->base + HW_LCDIF_DEBUG0) & DEBUG_VSYNC;
> + if (reg != last_reg);
> + break;
> + last_reg = reg;
> + loop--;
> + } while (loop != 0);
> + edges--;
> + }
> +
> + reg = readl(fbh->base + HW_LCDIF_CTRL);
> + reg |= CTRL_RUN;
> + writel(reg, fbh->base + HW_LCDIF_CTRL);
> +}
> +
> +/**
> + * @param fb_info Framebuffer information
> + */
> +static void stmfb_disable_controller(struct fb_info *fb_info)
> +{
> + struct imxfb_host *fbh = fb_info_to_imxfb_host(fb_info);
> + unsigned loop;
> + uint32_t reg;
> +
> + pr_debug("%s called\n", __func__);
> + /*
> + * Even if we disable the controller here, it will still continue
> + * until its FIFOs are running out of data
> + */
> + reg = readl(fbh->base + HW_LCDIF_CTRL);
> + reg &= ~CTRL_DOTCLK_MODE;
> + writel(reg, fbh->base + HW_LCDIF_CTRL);
> +
> + loop = 1000;
> + while (loop) {
> + reg = readl(fbh->base + HW_LCDIF_CTRL);
> + if (!(reg & CTRL_RUN))
> + break;
> + loop--;
> + }
> +
> + reg = readl(fbh->base + HW_LCDIF_VDCTRL4);
> + reg &= ~VDCTRL4_SYNC_SIGNALS_ON;
> + writel(reg, fbh->base + HW_LCDIF_VDCTRL4);
> +}
> +
> +/**
> + * Print some information about the current hardware state
> + * @param hw_dev STM video device
> + */
> +static void stmfb_info(struct device_d *hw_dev)
> +{
> + uint32_t reg;
> +
> + printf(" STM video hardware:\n");
> + printf(" Pixel clock: %u kHz\n", imx_get_lcdifclk());
> +
> + reg = readl(hw_dev->map_base + HW_LCDIF_CTRL);
> + switch (GET_WORD_LENGTH(reg)) {
> + case 0:
> + printf(" 16 bpp mode with %s colour scheme\n", reg & CTRL_DF16 ? "RGB565" : "ARGB1555");
> + switch (GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1))) {
> + case 0xf:
> + printf(" One pixel per halfword\n");
> + break;
> + case 0x3:
> + printf(" One pixel per word\n");
> + break;
> + default:
> + printf("Unknown pixel packaging: %u\n", GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1)));
Care to spend a line break?
> + }
> + break;
> + case 1:
> + case 2:
> + printf("Unsupported bpp mode yet!\n");
> + break;
> + case 3:
> + printf(" 24 bpp mode with %s colour scheme\n", reg & CTRL_DF24 ? "RGB888" : "RGB666");
> + switch (GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1))) {
> + case 0x7:
> + printf(" One pixel per word (xRGB xRGB xRGB ...)\n");
> + break;
> + case 0xf:
> + printf("Packed pixel format per word (RGBR GBRG BRGB ...)\n");
> + break;
> + default:
> + printf("Unknown pixel packaging: %u\n", GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1)));
ditto
> + }
> + break;
> + }
> +}
> +
> +/*
> + * There is only one video hardware instance available.
> + * It makes no sense to dynamically allocate this data
> + */
> +static struct imxfb_host host_data = {
> + .fb_data.fb_mode = stmfb_initialize_mode,
> + .fb_data.fb_enable = stmfb_enable_controller,
> + .fb_data.fb_disable = stmfb_disable_controller,
> + .fb_data.bits_per_pixel = 16,
> +};
> +
> +static int stmfb_probe(struct device_d *hw_dev)
> +{
> + struct imx_fb_videomode *pdata = hw_dev->platform_data;
> + struct device_d *fb_dev;
> +
> + if (pdata == NULL) {
> + pr_debug("STMFB: No platformdata. Giving up\n");
We also have dev_dbg and friends for this.
> + return -ENODEV;
> + }
> +
> + /* add runtime hardware info */
> + host_data.hw_dev = hw_dev;
> + host_data.base = (void*)hw_dev->map_base;
> +
> + /* add runtime video info */
> + host_data.fb_data.mode = pdata->mode_list;
> + host_data.fb_data.mode_cnt = pdata->mode_count;
> +
> + fb_dev = register_framebuffer(&host_data.fb_data, pdata->framebuffer, pdata->size);
> + if (fb_dev == NULL) {
> + pr_err("STMFB: Failed to register framebuffer\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static struct driver_d stmfb_driver = {
> + .name = "stmfb",
> + .probe = stmfb_probe,
> + .info = stmfb_info,
> +};
> +
> +static int stmfb_init(void)
> +{
> + return register_driver(&stmfb_driver);
> +}
> +
> +device_initcall(stmfb_init);
> +
> --
> 1.7.2.3
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* Re: [PATCH 09/11] STM378x: Add video driver for this platform
2010-10-22 18:59 ` Sascha Hauer
@ 2010-10-23 10:40 ` Juergen Beisert
0 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-23 10:40 UTC (permalink / raw)
To: barebox
Sascha Hauer wrote:
> On Fri, Oct 22, 2010 at 06:53:23PM +0200, Juergen Beisert wrote:
> > As there is currently no user of this driver (but coming soon) it is for
> > reference only.
> >
> > [...]
> > + default:
> > + printf("Unknown pixel packaging: %u\n", GET_BYTE_PACKAGING(readl(hw_dev->map_base + HW_LCDIF_CTRL1)));
>
> Care to spend a line break?
I like long lines... ;-)
Yes, I will add a line break the next time.
> > [...]
> > +static int stmfb_probe(struct device_d *hw_dev)
> > +{
> > + struct imx_fb_videomode *pdata = hw_dev->platform_data;
> > + struct device_d *fb_dev;
> > +
> > + if (pdata == NULL) {
> > + pr_debug("STMFB: No platformdata. Giving up\n");
>
> We also have dev_dbg and friends for this.
Yes.
jbe
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | Phone: +49-8766-939 228 |
Vertretung Sued/Muenchen, Germany | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de/ |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread
* [PATCH 10/11] Remove variable size restrictions
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
` (8 preceding siblings ...)
2010-10-22 16:53 ` [PATCH 09/11] STM378x: Add video driver for this platform Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
2010-10-22 16:53 ` [PATCH 11/11] Add doxygen documentation to the framebfuffer code Juergen Beisert
10 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
There is no really need for special variable types in these structures. Replace
them by standard C types with the same behaviour.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
include/fb.h | 41 ++++++++++++++++++++---------------------
1 files changed, 20 insertions(+), 21 deletions(-)
diff --git a/include/fb.h b/include/fb.h
index c004a56..e0cd6aa 100644
--- a/include/fb.h
+++ b/include/fb.h
@@ -43,19 +43,19 @@
struct fb_videomode {
const char *name; /* optional */
- u32 refresh; /* optional */
- u32 xres;
- u32 yres;
- u32 pixclock;
- u32 left_margin;
- u32 right_margin;
- u32 upper_margin;
- u32 lower_margin;
- u32 hsync_len;
- u32 vsync_len;
- u32 sync;
- u32 vmode;
- u32 flag;
+ unsigned refresh; /* optional */
+ unsigned xres;
+ unsigned yres;
+ unsigned pixclock;
+ unsigned left_margin;
+ unsigned right_margin;
+ unsigned upper_margin;
+ unsigned lower_margin;
+ unsigned hsync_len;
+ unsigned vsync_len;
+ unsigned sync;
+ unsigned vmode;
+ unsigned flag;
};
/* Interpretation of offset for color fields: All offsets are from the right,
@@ -69,10 +69,9 @@ struct fb_videomode {
* of available palette entries (i.e. # of entries = 1 << length).
*/
struct fb_bitfield {
- u32 offset; /* beginning of bitfield */
- u32 length; /* length of bitfield */
- u32 msb_right; /* != 0 : Most significant bit is */
- /* right */
+ unsigned offset; /* beginning of bitfield */
+ unsigned length; /* length of bitfield */
+ int msb_right; /* != 0 : Most significant bit is right */
};
struct fb_info;
@@ -97,11 +96,11 @@ struct fb_info {
struct device_d *fb_dev;
const struct fb_videomode *active_mode;
- u32 xres; /* visible resolution */
- u32 yres;
- u32 bits_per_pixel; /* guess what */
+ unsigned xres; /* visible resolution */
+ unsigned yres;
+ unsigned bits_per_pixel; /* guess what */
- u32 grayscale; /* != 0 Graylevels instead of colors */
+ int grayscale; /* != 0 Graylevels instead of colors */
struct fb_bitfield red; /* bitfield in fb mem if true color, */
struct fb_bitfield green; /* else only length is significant */
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread* [PATCH 11/11] Add doxygen documentation to the framebfuffer code
2010-10-22 16:53 Add dynamic video initialization to barebox Juergen Beisert
` (9 preceding siblings ...)
2010-10-22 16:53 ` [PATCH 10/11] Remove variable size restrictions Juergen Beisert
@ 2010-10-22 16:53 ` Juergen Beisert
10 siblings, 0 replies; 23+ messages in thread
From: Juergen Beisert @ 2010-10-22 16:53 UTC (permalink / raw)
To: barebox
Add some (hopyfully) helpful documentation to the source code.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
---
Documentation/developers_manual.dox | 1 +
Documentation/users_manual.dox | 1 +
drivers/video/fb.c | 221 +++++++++++++++++++++++++++++++++++
include/fb.h | 98 ++++++++++-----
4 files changed, 288 insertions(+), 33 deletions(-)
diff --git a/Documentation/developers_manual.dox b/Documentation/developers_manual.dox
index 620905e..609d0a0 100644
--- a/Documentation/developers_manual.dox
+++ b/Documentation/developers_manual.dox
@@ -21,5 +21,6 @@ This part of the documentation is intended for developers of @a barebox.
@li @subpage io_access_functions
@li @subpage mcfv4e_MCDlib
@li @subpage x86_runtime
+@li @subpage fb_for_developers
*/
diff --git a/Documentation/users_manual.dox b/Documentation/users_manual.dox
index cd2b99c..1f0e35b 100644
--- a/Documentation/users_manual.dox
+++ b/Documentation/users_manual.dox
@@ -12,5 +12,6 @@ work easier.
@li @subpage partitions
@li @subpage x86_bootloader
@li @subpage net_netconsole
+@li @subpage fb_for_users
*/
diff --git a/drivers/video/fb.c b/drivers/video/fb.c
index 15d993d..9381bd1 100644
--- a/drivers/video/fb.c
+++ b/drivers/video/fb.c
@@ -32,6 +32,13 @@ static int fb_ioctl(struct cdev* cdev, int req, void *data)
}
#ifdef CONFIG_VIDEO_DELAY_INIT
+/**
+ * Check if the framebuffer is already initialized
+ * @param fb_dev The framebuffer device to check
+ * @return 0 if the framebuffer is still uninitialized, -EPERM if already initialized
+ *
+ * @note Currently video mode initializing is a "one time only" task.
+ */
static int fb_check_if_already_initialized(struct device_d *fb_dev)
{
struct cdev *cdev = fb_dev->priv;
@@ -45,6 +52,9 @@ static int fb_check_if_already_initialized(struct device_d *fb_dev)
return 0;
}
+/**
+ * Change colour depth via device parameter
+ */
static int fb_cdepth_set(struct device_d *fb_dev, struct param_d *param, const char *val)
{
struct cdev *cdev = fb_dev->priv;
@@ -67,6 +77,9 @@ static int fb_cdepth_set(struct device_d *fb_dev, struct param_d *param, const c
#endif
#ifdef CONFIG_VIDEO_DELAY_ENABLING
+/**
+ * Enable/disable video output via device parameter
+ */
static int fb_enable_set(struct device_d *fb_dev, struct param_d *param, const char *val)
{
struct cdev *cdev = fb_dev->priv;
@@ -97,6 +110,10 @@ static int fb_enable_set(struct device_d *fb_dev, struct param_d *param, const c
}
#endif
+/**
+ * Output the list of supported video modes in this framebuffer
+ * @param host Platformdata of the hardware video device
+ */
static void fb_list_modes(struct fb_host *host)
{
unsigned u;
@@ -109,6 +126,14 @@ static void fb_list_modes(struct fb_host *host)
printf(" '%s'\n", host->mode[u].name);
}
+/**
+ * Call the video hardware driver to initialize the given video mode
+ * @param fb_dev Framebuffer device
+ * @param mode Mode description to initialize
+ * @return 0 on success
+ *
+ * @note This call does not imply enabling the video output device!
+ */
static int fb_activate_mode(struct device_d *fb_dev, const struct fb_videomode *mode)
{
struct cdev *cdev = fb_dev->priv;
@@ -133,6 +158,15 @@ static int fb_activate_mode(struct device_d *fb_dev, const struct fb_videomode *
}
#ifdef CONFIG_VIDEO_DELAY_INIT
+/**
+ * Setup the requested video mode via device parameter
+ * @param dev Device instance
+ * @param param FIXME
+ * @param name Video mode name to activate
+ * @return 0 on success
+ *
+ * @note One time setup only, changing video modes is currently not supported.
+ */
static int fb_mode_set(struct device_d *fb_dev, struct param_d *param, const char *name)
{
struct fb_host *host = fb_dev->platform_data;
@@ -211,6 +245,14 @@ static void fb_info(struct device_d *fb_dev)
fb_list_modes(fb_dev->platform_data);
}
+/**
+ * Add parameter to the framebuffer device on demand
+ * @param dev Device instance
+ * @return 0 on success
+ *
+ * Some parameter are only available (or usefull) if the intialization or
+ * enabling the video hardware is delayed.
+ */
static int add_fb_parameter(struct device_d *fb_dev)
{
#ifdef CONFIG_VIDEO_DELAY_INIT
@@ -299,6 +341,13 @@ static int framebuffer_init(void)
device_initcall(framebuffer_init);
+/**
+ * Create a new framebuffer device (for convenience)
+ * @param pinfo Video device's platform data for this framebuffer device
+ * @param base force framebuffer's base address to given value, or NULL for dynamically allocation
+ * @param sze force framebuffer's size to this value, or 0 for dynamically allocation
+ * @return Pointer to the newly created device or NULL on failure
+ */
struct device_d *register_framebuffer(struct fb_host *host, void *base, unsigned size)
{
struct device_d *fb_dev;
@@ -322,3 +371,175 @@ struct device_d *register_framebuffer(struct fb_host *host, void *base, unsigned
return fb_dev;
}
+
+/**
+@page fb_for_users Framebuffer handling for users
+
+@section regular_fb Static framebuffer setup
+
+After registering the video device the driver initializes the video hardware, clears the
+framebuffer (set all to zero) and enables the video output hardware. This will happen
+prior any shell code is running. In this case a user will see an activated video output device
+(an LC display for example or a connected CRT) showing a black screen.
+When the shell code starts, its possible to write some kind of image into the framebuffer memory
+to show a splash screen (refer 'bmp' command).
+
+@section delayed_fb Dynamic framebuffer setup
+
+To avoid a black screen until the image can be written, enabling the video output device
+can be delayed. Say 'y' to the "Delayed enabling" menu entry to activate this feature. This
+will initialize the video hardware, but do not enable the video output device. Instead it adds
+the parameter 'enable' to the framebuffer device. The video output device kept disabled until the
+command
+@verbatim
+barebox:/ fb0.enable=1
+@endverbatim
+is given in a shell script.
+
+If the platform supports more than one video output device its possible to select one of
+the supported ones at runtime. Say 'y' to the "Delayed initialization" menu entry to activate
+this feature. This will add the parameter 'mode' to the framebuffer device and will delay the
+initialization of the video hardware until the video output device gets specified.
+It will also delay the enabling of the video output device.
+
+Running the @b devinfo command on this fb0 device will output:
+@verbatim
+barebox:/ devinfo fb0
+base : 0x00000000
+size : 0x00000000
+driver: framebuffer
+
+ Video/Mode info:
+ Video output not enabled
+ Current video mode:
+ No video mode selected yet
+ Supported video mode(s):
+ 'QVGA'
+ 'VGA'
+Parameters:
+ cdepth = 16
+ mode = <NULL>
+ enable = <NULL>
+@endverbatim
+
+@note As long @b devinfo reports a @b base or @b size of zero there is
+@b no framebuffer memory yet!
+
+This framebuffer device is not initialized yet. As shown in the list, it
+supports two video modes: QVGA and VGA.
+
+So, the user can first specifiy the video output device with (for example)
+@verbatim
+barebox:/ fb0.mode="QVGA"
+@endverbatim
+
+After this the @b devinfo output changes to:
+@verbatim
+barebox:/ devinfo fb0
+base : 0x31fc0000
+size : 0x00040000
+driver: framebuffer
+
+ Video/Mode info:
+ Video output not enabled
+ Current video mode:
+ Name: QVGA
+ Refresh rate: 60 Hz
+ Horizontal active pixel: 320
+ Vertical active lines: 240
+ Pixel clock: 6500 kHz
+ Left/Right margin (pixel): 20/20
+ Upper/Lower margin (lines): 10/10
+ HSYNC length in pixel: 10, polarity: high
+ VSYNC length in lines: 5, polarity: high
+ Colour depth: 16 bpp
+ Supported video mode(s):
+ 'QVGA'
+ 'VGA'
+Parameters:
+ cdepth = 16
+ mode = QVGA
+ enable = <NULL>
+@endverbatim
+As one can see, the framebuffer has a @b base, a @b size and a video mode
+configuration now.
+@note Take care if setting a video mode fails. In this case @b base and @b size
+will kept at zero!
+
+With this setting its possible to write some kind of image into the framebuffer
+memory and enabling the video output as the final step at runtime
+@verbatim
+barebox:/ fb0.enable=1
+@endverbatim
+The video output is fully enabled now:
+@verbatim
+barebox:/ devinfo fb0
+base : 0x31fc0000
+size : 0x00040000
+driver: framebuffer
+
+ Video/Mode info:
+ Video output enabled
+ Current video mode:
+ Name: QVGA
+ Refresh rate: 60 Hz
+ Horizontal active pixel: 320
+ Vertical active lines: 240
+ Pixel clock: 6500 kHz
+ Left/Right margin (pixel): 20/20
+ Upper/Lower margin (lines): 10/10
+ HSYNC length in pixel: 10, polarity: high
+ VSYNC length in lines: 5, polarity: high
+ Colour depth: 16 bpp
+ Supported video mode(s):
+ 'QVGA'
+ 'VGA'
+Parameters:
+ cdepth = 16
+ mode = QVGA
+ enable = 1
+@endverbatim
+
+@section other_fb_params Other framebuffer parameter
+@verbatim
+fb0.cdepth=[1 | 4 | 8 | 16 | 24 | 32]
+@endverbatim
+
+Only available if "Delayed initialization" is selected. Colour depth to be used with the
+framebuffer. Its unit is "bit per pixel" and the default value is 16 bits per pixel (means
+"RGB565" format). This value can only be changed prior specifying the video mode.
+
+@note The possible values from the list above are hardware dependend.
+
+@note The default colour depth value may also depend on the hardware
+*/
+
+/**
+ * @page fb_for_developers Framebuffer handling for developers
+ * For the platform developer:
+ *
+ * When filling the platform specific video output device description you can still provide only one entry and
+ * you should setup the 'mode_cnt' entry with 0: Initialisation of the video hardware and enabling the
+ * video output device will still happen immediately.
+ *
+ * If you provide more than one video output device description use an array of this type. In this case the
+ * 'mode_cnt' entry must contain the count of existing array entries (> 1). Give each video output
+ * device description entry an unique name, because a user will select the required output device by this name
+ * at runtime.
+ *
+ * For the video hardware driver developer:
+ *
+ * Don't initialize a special video mode in your probe function (e.g. don't allocate any framebuffer memory aso).
+ * The framework will call back your exported fb_mode() function to do so (immediately ore delayed).
+ *
+ * Don't enable video output in your probe or exported fb_mode() function. Also do not switch on any LCD or
+ * backlight if any. The framework will call your exported fb_enable() function to do so (immediately ore delayed).
+ *
+ * If your hardware cannot handle the default 16 bit colour depth, change the 'bits_per_pixel' field
+ * prior registering your framebuffer.
+ *
+ * When your exported fb_mode() function is called, calculate the amount of memory you need for the requested
+ * video mode and colour depth, save this value to framebuffer's info struct in field 'size' and allocate some
+ * memory with this size for the framebuffer.
+ *
+ */
diff --git a/include/fb.h b/include/fb.h
index e0cd6aa..b17cc7d 100644
--- a/include/fb.h
+++ b/include/fb.h
@@ -18,19 +18,27 @@
/* vtotal = 121d/242n/484i => NTSC */
#define FB_SYNC_ON_GREEN 32 /* sync on green */
/* LC display related settings */
+/** LC display uses active high data enable signal */
#define FB_SYNC_DE_HIGH_ACT (1 << 6)
+/** LC display will latch its data at clock's rising edge */
#define FB_SYNC_CLK_INVERT (1 << 7)
+/** output RGB data inverted */
#define FB_SYNC_DATA_INVERT (1 << 8)
+/** Stop clock if no data is sent (required for passive displays) */
#define FB_SYNC_CLK_IDLE_EN (1 << 9)
+/** swap RGB to BGR */
#define FB_SYNC_SWAP_RGB (1 << 10)
+/** FIXME */
#define FB_SYNC_CLK_SEL_EN (1 << 11)
+/** enable special signals for SHARP displays (_very_ hardware specific) */
#define FB_SYNC_SHARP_MODE (1 << 31)
-#define FB_VMODE_NONINTERLACED 0 /* non interlaced */
-#define FB_VMODE_INTERLACED 1 /* interlaced */
+#define FB_VMODE_NONINTERLACED 0 /** non interlaced */
+#define FB_VMODE_INTERLACED 1 /** interlaced */
#define FB_VMODE_DOUBLE 2 /* double scan */
-#define FB_VMODE_ODD_FLD_FIRST 4 /* interlaced: top line first */
+#define FB_VMODE_ODD_FLD_FIRST 4 /** interlaced: top line first */
/* LC display related settings */
+/** output two screen parts at once (required for passive displays) */
#define FB_VMODE_DUAL_SCAN 8
#define FB_VMODE_MASK 255
@@ -42,19 +50,24 @@
#define KHZ2PICOS(a) (1000000000UL/(a))
struct fb_videomode {
- const char *name; /* optional */
- unsigned refresh; /* optional */
- unsigned xres;
- unsigned yres;
- unsigned pixclock;
- unsigned left_margin;
- unsigned right_margin;
- unsigned upper_margin;
- unsigned lower_margin;
- unsigned hsync_len;
- unsigned vsync_len;
- unsigned sync;
- unsigned vmode;
+ const char *name; /**< always required and must be unique */
+ unsigned refresh; /**< frame refresh rate in [Hz] (optional) */
+ unsigned xres; /**< visible horizontal pixel */
+ unsigned yres; /**< visible vertical pixel */
+ unsigned pixclock; /**< pixel clock period in [ps]. Refer
+ PICOS2KHZ/KHZ2PICOS macros */
+ unsigned left_margin; /**< distance in pixels between ending active HSYNC
+ and starting visible line content */
+ unsigned right_margin; /**< distance in pixels between ending visible line
+ content and starting active HSYNC */
+ unsigned upper_margin; /**< distance in lines between ending active VSYNC
+ and the first line with visible content */
+ unsigned lower_margin; /**< distance in lines between last line with
+ visible content and starting active VSYNC */
+ unsigned hsync_len; /**< HSYNC's active length in pixels */
+ unsigned vsync_len; /**< VSYNC's active lenght in lines */
+ unsigned sync; /**< sync information, refer FB_SYNC_* macros */
+ unsigned vmode; /**< video mode information, refer FB_VMODE_* macros */
unsigned flag;
};
@@ -69,18 +82,33 @@ struct fb_videomode {
* of available palette entries (i.e. # of entries = 1 << length).
*/
struct fb_bitfield {
- unsigned offset; /* beginning of bitfield */
- unsigned length; /* length of bitfield */
- int msb_right; /* != 0 : Most significant bit is right */
+ unsigned offset; /**< beginning of bitfield */
+ unsigned length; /**< length of bitfield */
+ int msb_right; /**< != 0 : Most significant bit is right */
};
struct fb_info;
+/**
+ * Framebuffer device's platform information
+ *
+ * The video hardware driver must set the following fields:
+ * - 'fb_mode' function to setup a specific video mode
+ * - 'fb_enable' function to activate the video output
+ * - 'fb_disable' function to deactivate the video output
+ * - 'fb_setcolreg' function to ???????? FIXME
+ *
+ * The video hardware driver can set default values for the following fields:
+ * - 'mode' if the driver supports only specific video modes.
+ * - 'mode_cnt' must be set, if 'mode_list' is given
+ * - 'bits_per_pixel' if the video hardware driver defaults to another bpp than 16
+ */
struct fb_host {
- const struct fb_videomode *mode;
- unsigned mode_cnt;
+ /* information about possible video mode(s) */
+ const struct fb_videomode *mode; /**< Array of modes */
+ unsigned mode_cnt; /**< count of entries in 'mode'. */
- struct device_d *hw_dev;
+ struct device_d *hw_dev; /**< the host device */
/* callbacks into the video hardware driver */
int (*fb_setcolreg)(struct fb_info*, unsigned, unsigned, unsigned, unsigned, unsigned);
@@ -88,24 +116,28 @@ struct fb_host {
void (*fb_enable)(struct fb_info*);
void (*fb_disable)(struct fb_info*);
- unsigned bits_per_pixel;
+ unsigned bits_per_pixel; /**< default bpp, 0 = use framebuffer's default */
};
+/**
+ * Framebuffer's runtime information
+ */
struct fb_info {
- struct fb_host *host;
- struct device_d *fb_dev;
+ struct fb_host *host; /**< host data this fb is based on */
+ struct device_d *fb_dev; /**< the framebuffer device */
+ /* information about current video mode */
+ /** the currently active video mode if set. Can be NULL = no video mode set yet */
const struct fb_videomode *active_mode;
+ unsigned xres; /**< visible horizontal pixel count */
+ unsigned yres; /**< visible vertical line count */
+ unsigned bits_per_pixel; /**< requested colour depth */
- unsigned xres; /* visible resolution */
- unsigned yres;
- unsigned bits_per_pixel; /* guess what */
-
- int grayscale; /* != 0 Graylevels instead of colors */
+ int grayscale; /**< != 0 Graylevels instead of colors */
- struct fb_bitfield red; /* bitfield in fb mem if true color, */
- struct fb_bitfield green; /* else only length is significant */
+ struct fb_bitfield red; /**< bitfield in fb mem if true color, */
+ struct fb_bitfield green; /**< else only length is significant */
struct fb_bitfield blue;
- struct fb_bitfield transp; /* transparency */
+ struct fb_bitfield transp; /**< transparency */
#ifdef CONFIG_VIDEO_DELAY_ENABLING
int enabled;
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 23+ messages in thread