From: Sascha Hauer <s.hauer@pengutronix.de>
To: barebox@lists.infradead.org
Subject: [PATCH 5/7] mci mxs: make the mci_host a member of mxs_mci_host
Date: Mon, 28 Feb 2011 10:43:53 +0100 [thread overview]
Message-ID: <1298886235-1769-6-git-send-email-s.hauer@pengutronix.de> (raw)
In-Reply-To: <1298886235-1769-1-git-send-email-s.hauer@pengutronix.de>
This allows for more type safety. passing a struct device_d
internally in the driver is not a good idea. Also, this
patch adds a void __iomem *regs to mxs_mci_host. dev->map_base
should not be used for register accesses.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
drivers/mci/mxs.c | 196 ++++++++++++++++++++++++++--------------------------
1 files changed, 98 insertions(+), 98 deletions(-)
diff --git a/drivers/mci/mxs.c b/drivers/mci/mxs.c
index bc177f5..7f8f3f8 100644
--- a/drivers/mci/mxs.c
+++ b/drivers/mci/mxs.c
@@ -166,6 +166,8 @@
#endif
struct mxs_mci_host {
+ struct mci_host host;
+ void __iomem *regs;
unsigned clock; /* current clock speed in Hz ("0" if disabled) */
unsigned index;
#ifdef CONFIG_MCI_INFO
@@ -175,16 +177,16 @@ struct mxs_mci_host {
int bus_width:2; /* 0 = 1 bit, 1 = 4 bit, 2 = 8 bit */
};
+#define to_mxs_mci(mxs) container_of(mxs, struct mxs_mci_host, host)
+
/**
* Get the SSP clock rate
* @param hw_dev Host interface device instance
* @return Unit's clock in [Hz]
*/
-static unsigned mxs_mci_get_unit_clock(struct device_d *hw_dev)
+static unsigned mxs_mci_get_unit_clock(struct mxs_mci_host *mxs_mci)
{
- struct mxs_mci_host *host_data = GET_HOST_DATA(hw_dev);
-
- return imx_get_sspclk(host_data->index);
+ return imx_get_sspclk(mxs_mci->index);
}
/**
@@ -193,7 +195,7 @@ static unsigned mxs_mci_get_unit_clock(struct device_d *hw_dev)
* @param cmd Command description
* @return Response bytes count, -EINVAL for unsupported response types
*/
-static int mxs_mci_get_cards_response(struct device_d *hw_dev, struct mci_cmd *cmd)
+static int mxs_mci_get_cards_response(struct mxs_mci_host *mxs_mci, struct mci_cmd *cmd)
{
switch (cmd->resp_type) {
case MMC_RSP_NONE:
@@ -202,14 +204,14 @@ static int mxs_mci_get_cards_response(struct device_d *hw_dev, struct mci_cmd *c
case MMC_RSP_R1:
case MMC_RSP_R1b:
case MMC_RSP_R3:
- cmd->response[0] = readl(hw_dev->map_base + HW_SSP_SDRESP0);
+ cmd->response[0] = readl(mxs_mci->regs + HW_SSP_SDRESP0);
return 1;
case MMC_RSP_R2:
- cmd->response[3] = readl(hw_dev->map_base + HW_SSP_SDRESP0);
- cmd->response[2] = readl(hw_dev->map_base + HW_SSP_SDRESP1);
- cmd->response[1] = readl(hw_dev->map_base + HW_SSP_SDRESP2);
- cmd->response[0] = readl(hw_dev->map_base + HW_SSP_SDRESP3);
+ cmd->response[3] = readl(mxs_mci->regs + HW_SSP_SDRESP0);
+ cmd->response[2] = readl(mxs_mci->regs + HW_SSP_SDRESP1);
+ cmd->response[1] = readl(mxs_mci->regs + HW_SSP_SDRESP2);
+ cmd->response[0] = readl(mxs_mci->regs + HW_SSP_SDRESP3);
return 4;
}
@@ -222,10 +224,10 @@ static int mxs_mci_get_cards_response(struct device_d *hw_dev, struct mci_cmd *c
*
* Can also stop the clock to save power
*/
-static void mxs_mci_finish_request(struct device_d *hw_dev)
+static void mxs_mci_finish_request(struct mxs_mci_host *mxs_mci)
{
/* stop the engines (normaly already done) */
- writel(SSP_CTRL0_RUN, hw_dev->map_base + HW_SSP_CTRL0 + 8);
+ writel(SSP_CTRL0_RUN, mxs_mci->regs + HW_SSP_CTRL0 + 8);
}
/**
@@ -260,13 +262,13 @@ static int mxs_mci_get_cmd_error(unsigned status)
* @param hw_dev Host interface device instance
* @param to Timeout value in MCI card's bus clocks
*/
-static void mxs_mci_setup_timeout(struct device_d *hw_dev, unsigned to)
+static void mxs_mci_setup_timeout(struct mxs_mci_host *mxs_mci, unsigned to)
{
uint32_t reg;
- reg = readl(hw_dev->map_base + HW_SSP_TIMING) & ~SSP_TIMING_TIMEOUT_MASK;
+ reg = readl(mxs_mci->regs + HW_SSP_TIMING) & ~SSP_TIMING_TIMEOUT_MASK;
reg |= SSP_TIMING_TIMEOUT(to);
- writel(reg, hw_dev->map_base + HW_SSP_TIMING);
+ writel(reg, mxs_mci->regs + HW_SSP_TIMING);
}
/**
@@ -280,7 +282,7 @@ static void mxs_mci_setup_timeout(struct device_d *hw_dev, unsigned to)
* may fail whith high clock speeds. If you receive -EIO errors you can try
* again with reduced clock speeds.
*/
-static int mxs_mci_read_data(struct device_d *hw_dev, void *buffer, unsigned length)
+static int mxs_mci_read_data(struct mxs_mci_host *mxs_mci, void *buffer, unsigned length)
{
uint32_t *p = buffer;
@@ -291,10 +293,10 @@ static int mxs_mci_read_data(struct device_d *hw_dev, void *buffer, unsigned len
}
while ((length != 0) &&
- ((readl(hw_dev->map_base + HW_SSP_STATUS) & SSP_STATUS_ERROR) == 0)) {
+ ((readl(mxs_mci->regs + HW_SSP_STATUS) & SSP_STATUS_ERROR) == 0)) {
/* TODO sort out FIFO overflows and emit -EOI for this case */
- if ((readl(hw_dev->map_base + HW_SSP_STATUS) & SSP_STATUS_FIFO_EMPTY) == 0) {
- *p = readl(hw_dev->map_base + HW_SSP_DATA);
+ if ((readl(mxs_mci->regs + HW_SSP_STATUS) & SSP_STATUS_FIFO_EMPTY) == 0) {
+ *p = readl(mxs_mci->regs + HW_SSP_DATA);
p++;
length -= 4;
}
@@ -318,7 +320,7 @@ static int mxs_mci_read_data(struct device_d *hw_dev, void *buffer, unsigned len
* may fail with high clock speeds. If you receive -EIO errors you can try
* again with reduced clock speeds.
*/
-static int mxs_mci_write_data(struct device_d *hw_dev, const void *buffer, unsigned length)
+static int mxs_mci_write_data(struct mxs_mci_host *mxs_mci, const void *buffer, unsigned length)
{
const uint32_t *p = buffer;
@@ -329,10 +331,10 @@ static int mxs_mci_write_data(struct device_d *hw_dev, const void *buffer, unsig
}
while ((length != 0) &&
- ((readl(hw_dev->map_base + HW_SSP_STATUS) & SSP_STATUS_ERROR) == 0)) {
+ ((readl(mxs_mci->regs + HW_SSP_STATUS) & SSP_STATUS_ERROR) == 0)) {
/* TODO sort out FIFO overflows and emit -EOI for this case */
- if ((readl(hw_dev->map_base + HW_SSP_STATUS) & SSP_STATUS_FIFO_FULL) == 0) {
- writel(*p, hw_dev->map_base + HW_SSP_DATA);
+ if ((readl(mxs_mci->regs + HW_SSP_STATUS) & SSP_STATUS_FIFO_FULL) == 0) {
+ writel(*p, mxs_mci->regs + HW_SSP_DATA);
p++;
length -= 4;
}
@@ -349,7 +351,7 @@ static int mxs_mci_write_data(struct device_d *hw_dev, const void *buffer, unsig
* @param data Data transfer description (might be NULL)
* @return 0 on success
*/
-static int mxs_mci_transfer_data(struct device_d *hw_dev, struct mci_data *data)
+static int mxs_mci_transfer_data(struct mxs_mci_host *mxs_mci, struct mci_data *data)
{
unsigned length;
@@ -377,13 +379,13 @@ static int mxs_mci_transfer_data(struct device_d *hw_dev, struct mci_data *data)
*
* Start the transaction right now
*/
- writel(SSP_CTRL0_RUN, hw_dev->map_base + HW_SSP_CTRL0 + 4);
+ writel(SSP_CTRL0_RUN, mxs_mci->regs + HW_SSP_CTRL0 + 4);
if (data != NULL) {
if (data->flags & MMC_DATA_READ)
- return mxs_mci_read_data(hw_dev, data->dest, length);
+ return mxs_mci_read_data(mxs_mci, data->dest, length);
else
- return mxs_mci_write_data(hw_dev, data->src, length);
+ return mxs_mci_write_data(mxs_mci, data->src, length);
}
return 0;
@@ -428,33 +430,33 @@ static uint32_t mxs_mci_prepare_transfer_setup(unsigned cmd_flags, unsigned data
* - "broadcast commands with response (BCR)"
* - "addressed command (AC)" with response, but without data
*/
-static int mxs_mci_std_cmds(struct device_d *hw_dev, struct mci_cmd *cmd)
+static int mxs_mci_std_cmds(struct mxs_mci_host *mxs_mci, struct mci_cmd *cmd)
{
/* setup command and transfer parameters */
writel(mxs_mci_prepare_transfer_setup(cmd->resp_type, 0) |
- SSP_CTRL0_ENABLE, hw_dev->map_base + HW_SSP_CTRL0);
+ SSP_CTRL0_ENABLE, mxs_mci->regs + HW_SSP_CTRL0);
/* prepare the command, when no response is expected add a few trailing clocks */
writel(SSP_CMD0_CMD(cmd->cmdidx) |
(cmd->resp_type & MMC_RSP_PRESENT ? 0 : SSP_CMD0_APPEND_8CYC),
- hw_dev->map_base + HW_SSP_CMD0);
+ mxs_mci->regs + HW_SSP_CMD0);
/* prepare command's arguments */
- writel(cmd->cmdarg, hw_dev->map_base + HW_SSP_CMD1);
+ writel(cmd->cmdarg, mxs_mci->regs + HW_SSP_CMD1);
- mxs_mci_setup_timeout(hw_dev, 0xffff);
+ mxs_mci_setup_timeout(mxs_mci, 0xffff);
/* start the transfer */
- writel(SSP_CTRL0_RUN, hw_dev->map_base + HW_SSP_CTRL0 + 4);
+ writel(SSP_CTRL0_RUN, mxs_mci->regs + HW_SSP_CTRL0 + 4);
/* wait until finished */
- while (readl(hw_dev->map_base + HW_SSP_CTRL0) & SSP_CTRL0_RUN)
+ while (readl(mxs_mci->regs + HW_SSP_CTRL0) & SSP_CTRL0_RUN)
;
if (cmd->resp_type & MMC_RSP_PRESENT)
- mxs_mci_get_cards_response(hw_dev, cmd);
+ mxs_mci_get_cards_response(mxs_mci, cmd);
- return mxs_mci_get_cmd_error(readl(hw_dev->map_base + HW_SSP_STATUS));
+ return mxs_mci_get_cmd_error(readl(mxs_mci->regs + HW_SSP_STATUS));
}
/**
@@ -464,10 +466,9 @@ static int mxs_mci_std_cmds(struct device_d *hw_dev, struct mci_cmd *cmd)
* @param data The data information (buffer, direction aso.) May be NULL
* @return 0 on success
*/
-static int mxs_mci_adtc(struct device_d *hw_dev, struct mci_cmd *cmd,
+static int mxs_mci_adtc(struct mxs_mci_host *mxs_mci, struct mci_cmd *cmd,
struct mci_data *data)
{
- struct mxs_mci_host *host_data = (struct mxs_mci_host*)GET_HOST_DATA(hw_dev);
uint32_t xfer_cnt, log2blocksize, block_cnt;
int err;
@@ -483,52 +484,52 @@ static int mxs_mci_adtc(struct device_d *hw_dev, struct mci_cmd *cmd,
/* setup command and transfer parameters */
#ifdef CONFIG_ARCH_IMX23
writel(mxs_mci_prepare_transfer_setup(cmd->resp_type, data != NULL ? data->flags : 0) |
- SSP_CTRL0_BUS_WIDTH(host_data->bus_width) |
+ SSP_CTRL0_BUS_WIDTH(mxs_mci->bus_width) |
(xfer_cnt != 0 ? SSP_CTRL0_DATA_XFER : 0) | /* command plus data */
SSP_CTRL0_ENABLE |
SSP_CTRL0_XFER_COUNT(xfer_cnt), /* byte count to be transfered */
- hw_dev->map_base + HW_SSP_CTRL0);
+ mxs_mci->regs + HW_SSP_CTRL0);
/* prepare the command and the transfered data count */
writel(SSP_CMD0_CMD(cmd->cmdidx) |
SSP_CMD0_BLOCK_SIZE(log2blocksize) |
SSP_CMD0_BLOCK_COUNT(block_cnt) |
(cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION ? SSP_CMD0_APPEND_8CYC : 0),
- hw_dev->map_base + HW_SSP_CMD0);
+ mxs_mci->regs + HW_SSP_CMD0);
#endif
#ifdef CONFIG_ARCH_IMX28
writel(mxs_mci_prepare_transfer_setup(cmd->resp_type, data != NULL ? data->flags : 0) |
- SSP_CTRL0_BUS_WIDTH(host_data->bus_width) |
+ SSP_CTRL0_BUS_WIDTH(mxs_mci->bus_width) |
(xfer_cnt != 0 ? SSP_CTRL0_DATA_XFER : 0) | /* command plus data */
SSP_CTRL0_ENABLE,
- hw_dev->map_base + HW_SSP_CTRL0);
- writel(xfer_cnt, hw_dev->map_base + HW_SSP_XFER_COUNT);
+ mxs_mci->regs + HW_SSP_CTRL0);
+ writel(xfer_cnt, mxs_mci->regs + HW_SSP_XFER_COUNT);
/* prepare the command and the transfered data count */
writel(SSP_CMD0_CMD(cmd->cmdidx) |
(cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION ? SSP_CMD0_APPEND_8CYC : 0),
- hw_dev->map_base + HW_SSP_CMD0);
+ mxs_mci->regs + HW_SSP_CMD0);
writel(SSP_BLOCK_SIZE(log2blocksize) |
SSP_BLOCK_COUNT(block_cnt),
- hw_dev->map_base + HW_SSP_BLOCK_SIZE);
+ mxs_mci->regs + HW_SSP_BLOCK_SIZE);
#endif
/* prepare command's arguments */
- writel(cmd->cmdarg, hw_dev->map_base + HW_SSP_CMD1);
+ writel(cmd->cmdarg, mxs_mci->regs + HW_SSP_CMD1);
- mxs_mci_setup_timeout(hw_dev, 0xffff);
+ mxs_mci_setup_timeout(mxs_mci, 0xffff);
- err = mxs_mci_transfer_data(hw_dev, data);
+ err = mxs_mci_transfer_data(mxs_mci, data);
if (err != 0) {
pr_debug(" Transfering data failed\n");
return err;
}
/* wait until finished */
- while (readl(hw_dev->map_base + HW_SSP_CTRL0) & SSP_CTRL0_RUN)
+ while (readl(mxs_mci->regs + HW_SSP_CTRL0) & SSP_CTRL0_RUN)
;
- mxs_mci_get_cards_response(hw_dev, cmd);
+ mxs_mci_get_cards_response(mxs_mci, cmd);
return 0;
}
@@ -554,7 +555,7 @@ static int mxs_mci_adtc(struct device_d *hw_dev, struct mci_cmd *cmd,
* @note Up to "SSP unit DIV" the outer world must care. This routine only
* handles the "SSP DIV".
*/
-static unsigned mxs_mci_setup_clock_speed(struct device_d *hw_dev, unsigned nc)
+static unsigned mxs_mci_setup_clock_speed(struct mxs_mci_host *mxs_mci, unsigned nc)
{
unsigned ssp, div, rate, reg;
@@ -563,7 +564,7 @@ static unsigned mxs_mci_setup_clock_speed(struct device_d *hw_dev, unsigned nc)
return 0;
}
- ssp = mxs_mci_get_unit_clock(hw_dev);
+ ssp = mxs_mci_get_unit_clock(mxs_mci);
for (div = 2; div < 255; div += 2) {
rate = DIV_ROUND_CLOSEST(DIV_ROUND_CLOSEST(ssp, nc), div);
@@ -575,9 +576,9 @@ static unsigned mxs_mci_setup_clock_speed(struct device_d *hw_dev, unsigned nc)
return 0;
}
- reg = readl(hw_dev->map_base + HW_SSP_TIMING) & SSP_TIMING_TIMEOUT_MASK;
+ reg = readl(mxs_mci->regs + HW_SSP_TIMING) & SSP_TIMING_TIMEOUT_MASK;
reg |= SSP_TIMING_CLOCK_DIVIDE(div) | SSP_TIMING_CLOCK_RATE(rate - 1);
- writel(reg, hw_dev->map_base + HW_SSP_TIMING);
+ writel(reg, mxs_mci->regs + HW_SSP_TIMING);
return ssp / div / rate;
}
@@ -588,10 +589,10 @@ static unsigned mxs_mci_setup_clock_speed(struct device_d *hw_dev, unsigned nc)
*
* This will reset everything in all registers of this unit! (FIXME)
*/
-static void mxs_mci_reset(struct device_d *hw_dev)
+static void mxs_mci_reset(struct mxs_mci_host *mxs_mci)
{
- writel(SSP_CTRL0_SFTRST, hw_dev->map_base + HW_SSP_CTRL0 + 8);
- while (readl(hw_dev->map_base + HW_SSP_CTRL0) & SSP_CTRL0_SFTRST)
+ writel(SSP_CTRL0_SFTRST, mxs_mci->regs + HW_SSP_CTRL0 + 8);
+ while (readl(mxs_mci->regs + HW_SSP_CTRL0) & SSP_CTRL0_SFTRST)
;
}
@@ -605,24 +606,23 @@ static void mxs_mci_reset(struct device_d *hw_dev)
*/
static int mxs_mci_initialize(struct mci_host *host, struct device_d *mci_dev)
{
- struct device_d *hw_dev = host->hw_dev;
- struct mxs_mci_host *host_data = (struct mxs_mci_host*)GET_HOST_DATA(hw_dev);
+ struct mxs_mci_host *mxs_mci = to_mxs_mci(host);
/* enable the clock to this unit to be able to reset it */
- writel(SSP_CTRL0_CLKGATE, hw_dev->map_base + HW_SSP_CTRL0 + 8);
+ writel(SSP_CTRL0_CLKGATE, mxs_mci->regs + HW_SSP_CTRL0 + 8);
/* reset the unit */
- mxs_mci_reset(hw_dev);
+ mxs_mci_reset(mxs_mci);
/* restore the last settings */
- host->clock = host_data->clock = mxs_mci_setup_clock_speed(hw_dev, host->clock);
- mxs_mci_setup_timeout(hw_dev, 0xffff);
+ host->clock = mxs_mci->clock = mxs_mci_setup_clock_speed(mxs_mci, host->clock);
+ mxs_mci_setup_timeout(mxs_mci, 0xffff);
writel(SSP_CTRL0_IGNORE_CRC |
- SSP_CTRL0_BUS_WIDTH(host_data->bus_width),
- hw_dev->map_base + HW_SSP_CTRL0);
+ SSP_CTRL0_BUS_WIDTH(mxs_mci->bus_width),
+ mxs_mci->regs + HW_SSP_CTRL0);
writel(SSP_CTRL1_POLARITY |
SSP_CTRL1_SSP_MODE(3) |
- SSP_CTRL1_WORD_LENGTH(7), hw_dev->map_base + HW_SSP_CTRL1);
+ SSP_CTRL1_WORD_LENGTH(7), mxs_mci->regs + HW_SSP_CTRL1);
return 0;
}
@@ -637,15 +637,15 @@ static int mxs_mci_initialize(struct mci_host *host, struct device_d *mci_dev)
static int mxs_mci_request(struct mci_host *host, struct mci_cmd *cmd,
struct mci_data *data)
{
- struct device_d *hw_dev = host->hw_dev;
+ struct mxs_mci_host *mxs_mci = to_mxs_mci(host);
int rc;
if ((cmd->resp_type == 0) || (data == NULL))
- rc = mxs_mci_std_cmds(hw_dev, cmd);
+ rc = mxs_mci_std_cmds(mxs_mci, cmd);
else
- rc = mxs_mci_adtc(hw_dev, cmd, data); /* with response and data */
+ rc = mxs_mci_adtc(mxs_mci, cmd, data); /* with response and data */
- mxs_mci_finish_request(hw_dev); /* TODO */
+ mxs_mci_finish_request(mxs_mci); /* TODO */
return rc;
}
@@ -661,25 +661,24 @@ static int mxs_mci_request(struct mci_host *host, struct mci_cmd *cmd,
static void mxs_mci_set_ios(struct mci_host *host, struct device_d *mci_dev,
unsigned bus_width, unsigned clock)
{
- struct device_d *hw_dev = host->hw_dev;
- struct mxs_mci_host *host_data = (struct mxs_mci_host*)GET_HOST_DATA(hw_dev);
+ struct mxs_mci_host *mxs_mci = to_mxs_mci(host);
switch (bus_width) {
case 8:
- host_data->bus_width = 2;
+ mxs_mci->bus_width = 2;
host->bus_width = 8; /* 8 bit is possible */
break;
case 4:
- host_data->bus_width = 1;
+ mxs_mci->bus_width = 1;
host->bus_width = 4; /* 4 bit is possible */
break;
default:
- host_data->bus_width = 0;
+ mxs_mci->bus_width = 0;
host->bus_width = 1; /* 1 bit is possible */
break;
}
- host->clock = host_data->clock = mxs_mci_setup_clock_speed(hw_dev, clock);
+ host->clock = mxs_mci->clock = mxs_mci_setup_clock_speed(mxs_mci, clock);
pr_debug("IO settings: bus width=%d, frequency=%u Hz\n", host->bus_width,
host->clock);
}
@@ -691,13 +690,13 @@ const unsigned char bus_width[3] = { 1, 4, 8 };
static void mxs_mci_info(struct device_d *hw_dev)
{
- struct mxs_mci_host *host_data = GET_HOST_DATA(hw_dev);
+ struct mxs_mci_host *mxs_mci = GET_HOST_DATA(hw_dev);
printf(" Interface\n");
- printf(" Min. bus clock: %u Hz\n", host_data->f_min);
- printf(" Max. bus clock: %u Hz\n", host_data->f_max);
- printf(" Current bus clock: %u Hz\n", host_data->clock);
- printf(" Bus width: %u bit\n", bus_width[host_data->bus_width]);
+ printf(" Min. bus clock: %u Hz\n", mxs_mci->f_min);
+ printf(" Max. bus clock: %u Hz\n", mxs_mci->f_max);
+ printf(" Current bus clock: %u Hz\n", mxs_mci->clock);
+ printf(" Bus width: %u bit\n", bus_width[mxs_mci->bus_width]);
printf("\n");
}
#endif
@@ -705,7 +704,7 @@ static void mxs_mci_info(struct device_d *hw_dev)
static int mxs_mci_probe(struct device_d *hw_dev)
{
struct mxs_mci_platform_data *pd = hw_dev->platform_data;
- struct mxs_mci_host *host_data;
+ struct mxs_mci_host *mxs_mci;
struct mci_host *host;
if (hw_dev->platform_data == NULL) {
@@ -713,62 +712,63 @@ static int mxs_mci_probe(struct device_d *hw_dev)
return -EINVAL;
}
- host = xzalloc(sizeof(struct mxs_mci_host) + sizeof(struct mci_host));
- host_data = (struct mxs_mci_host*)&host[1];
+ mxs_mci = xzalloc(sizeof(*mxs_mci));
+ host = &mxs_mci->host;
- hw_dev->priv = host_data;
+ hw_dev->priv = mxs_mci;
host->hw_dev = hw_dev;
host->send_cmd = mxs_mci_request,
host->set_ios = mxs_mci_set_ios,
host->init = mxs_mci_initialize,
+ mxs_mci->regs = (void *)hw_dev->map_base;
/* feed forward the platform specific values */
host->voltages = pd->voltages;
host->host_caps = pd->caps;
#ifdef CONFIG_ARCH_IMX23
- host_data->index = 0; /* there is only one clock for all */
+ mxs_mci->index = 0; /* there is only one clock for all */
#endif
#ifdef CONFIG_ARCH_IMX28
/* one dedicated clock per unit */
switch (hw_dev->map_base) {
case IMX_SSP0_BASE:
- host_data->index = 0;
+ mxs_mci->index = 0;
break;
case IMX_SSP1_BASE:
- host_data->index = 1;
+ mxs_mci->index = 1;
break;
case IMX_SSP2_BASE:
- host_data->index = 2;
+ mxs_mci->index = 2;
break;
case IMX_SSP3_BASE:
- host_data->index = 3;
+ mxs_mci->index = 3;
break;
default:
- pr_debug("Unknown SSP unit at address 0x%08x\n", hw_dev->map_base);
+ pr_debug("Unknown SSP unit at address 0x%08x\n", mxs_mci->regs);
return 0;
}
#endif
if (pd->f_min == 0) {
- host->f_min = mxs_mci_get_unit_clock(hw_dev) / 254 / 256;
+ host->f_min = mxs_mci_get_unit_clock(mxs_mci) / 254 / 256;
pr_debug("Min. frequency is %u Hz\n", host->f_min);
} else {
host->f_min = pd->f_min;
pr_debug("Min. frequency is %u Hz, could be %u Hz\n",
- host->f_min, mxs_mci_get_unit_clock(hw_dev) / 254 / 256);
+ host->f_min, mxs_mci_get_unit_clock(mxs_mci) / 254 / 256);
}
if (pd->f_max == 0) {
- host->f_max = mxs_mci_get_unit_clock(hw_dev) / 2 / 1;
+ host->f_max = mxs_mci_get_unit_clock(mxs_mci) / 2 / 1;
pr_debug("Max. frequency is %u Hz\n", host->f_max);
} else {
host->f_max = pd->f_max;
pr_debug("Max. frequency is %u Hz, could be %u Hz\n",
- host->f_max, mxs_mci_get_unit_clock(hw_dev) / 2 / 1);
+ host->f_max, mxs_mci_get_unit_clock(mxs_mci) / 2 / 1);
}
#ifdef CONFIG_MCI_INFO
- host_data->f_min = host->f_min;
- host_data->f_max = host->f_max;
+ mxs_mci->f_min = host->f_min;
+ mxs_mci->f_max = host->f_max;
#endif
return mci_register(host);
--
1.7.2.3
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2011-02-28 9:44 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-02-28 9:43 mmc: i.MX23/28 patches Sascha Hauer
2011-02-28 9:43 ` [PATCH 1/7] mci i.MX23/28: rename driver to mxs.c Sascha Hauer
2011-02-28 9:43 ` [PATCH 2/7] mci mxs: put only once used function inline Sascha Hauer
2011-02-28 9:43 ` [PATCH 3/7] mci mxs: give functions a uniq mxs_mci_ namespace Sascha Hauer
2011-02-28 9:43 ` [PATCH 4/7] mci mxs: rename mci_pdata to host Sascha Hauer
2011-02-28 9:43 ` Sascha Hauer [this message]
2011-02-28 9:43 ` [PATCH 6/7] mci mxs: no need to call mxs_mci_setup_clock_speed in init Sascha Hauer
2011-02-28 9:43 ` [PATCH 7/7] ARM tx28stk5: limit mmc max frequency to 25MHz Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1298886235-1769-6-git-send-email-s.hauer@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox