From: Sascha Hauer <s.hauer@pengutronix.de>
To: barebox@lists.infradead.org
Subject: [PATCH 2/2] ppc: remove unused bd_t
Date: Sun, 15 Apr 2012 16:57:14 +0200 [thread overview]
Message-ID: <1334501834-32001-3-git-send-email-s.hauer@pengutronix.de> (raw)
In-Reply-To: <1334501834-32001-1-git-send-email-s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/ppc/include/asm/barebox.h | 103 ----------------------------------------
1 file changed, 103 deletions(-)
diff --git a/arch/ppc/include/asm/barebox.h b/arch/ppc/include/asm/barebox.h
index ac81495..a08e998 100644
--- a/arch/ppc/include/asm/barebox.h
+++ b/arch/ppc/include/asm/barebox.h
@@ -28,107 +28,4 @@
#ifndef __BAREBOX_H__
#define __BAREBOX_H__
-/*
- * Board information passed to Linux kernel from barebox
- *
- * include/asm-ppc/barebox.h
- */
-
-#ifndef __ASSEMBLY__
-
-typedef struct bd_info {
- unsigned long bi_memstart; /* start of DRAM memory */
- unsigned long bi_memsize; /* size of DRAM memory in bytes */
- unsigned long bi_flashstart; /* start of FLASH memory */
- unsigned long bi_flashsize; /* size of FLASH memory */
- unsigned long bi_flashoffset; /* reserved area for startup monitor */
- unsigned long bi_sramstart; /* start of SRAM memory */
- unsigned long bi_sramsize; /* size of SRAM memory */
-#if defined(CONFIG_5xx) || defined(CONFIG_8xx) || defined(CONFIG_8260) \
- || defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
- unsigned long bi_immr_base; /* base of IMMR register */
-#endif
-#if defined(CONFIG_MPC5xxx)
- unsigned long bi_mbar_base; /* base of internal registers */
-#endif
-#if defined(CONFIG_MPC83XX)
- unsigned long bi_immrbar;
-#endif
-#if defined(CONFIG_MPC8220)
- unsigned long bi_mbar_base; /* base of internal registers */
- unsigned long bi_inpfreq; /* Input Freq, In MHz */
- unsigned long bi_pcifreq; /* PCI Freq, in MHz */
- unsigned long bi_pevfreq; /* PEV Freq, in MHz */
- unsigned long bi_flbfreq; /* Flexbus Freq, in MHz */
- unsigned long bi_vcofreq; /* VCO Freq, in MHz */
-#endif
- unsigned long bi_bootflags; /* boot / reboot flag (for LynxOS) */
- unsigned long bi_ip_addr; /* IP Address */
- unsigned char bi_enetaddr[6]; /* Ethernet adress */
- unsigned short bi_ethspeed; /* Ethernet speed in Mbps */
- unsigned long bi_intfreq; /* Internal Freq, in MHz */
- unsigned long bi_busfreq; /* Bus Freq, in MHz */
-#if defined(CONFIG_CPM2)
- unsigned long bi_cpmfreq; /* CPM_CLK Freq, in MHz */
- unsigned long bi_brgfreq; /* BRG_CLK Freq, in MHz */
- unsigned long bi_sccfreq; /* SCC_CLK Freq, in MHz */
- unsigned long bi_vco; /* VCO Out from PLL, in MHz */
-#endif
-#if defined(CONFIG_MPC5xxx)
- unsigned long bi_ipbfreq; /* IPB Bus Freq, in MHz */
- unsigned long bi_pcifreq; /* PCI Bus Freq, in MHz */
-#endif
- unsigned long bi_baudrate; /* Console Baudrate */
-#if defined(CONFIG_405) || \
- defined(CONFIG_405GP) || \
- defined(CONFIG_405CR) || \
- defined(CONFIG_405EP) || \
- defined(CONFIG_440)
- unsigned char bi_s_version[4]; /* Version of this structure */
- unsigned char bi_r_version[32]; /* Version of the ROM (AMCC) */
- unsigned int bi_procfreq; /* CPU (Internal) Freq, in Hz */
- unsigned int bi_plb_busfreq; /* PLB Bus speed, in Hz */
- unsigned int bi_pci_busfreq; /* PCI Bus speed, in Hz */
- unsigned char bi_pci_enetaddr[6]; /* PCI Ethernet MAC address */
-#endif
-#if defined(CONFIG_HYMOD)
- hymod_conf_t bi_hymod_conf; /* hymod configuration information */
-#endif
-
-#ifdef CONFIG_HAS_ETH1
- /* second onboard ethernet port */
- unsigned char bi_enet1addr[6];
-#endif
-#ifdef CONFIG_HAS_ETH2
- /* third onboard ethernet port */
- unsigned char bi_enet2addr[6];
-#endif
-#ifdef CONFIG_HAS_ETH3
- unsigned char bi_enet3addr[6];
-#endif
-
-#if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined (CONFIG_440GX) || \
- defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
- defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
- unsigned int bi_opbfreq; /* OPB clock in Hz */
- int bi_iic_fast[2]; /* Use fast i2c mode */
-#endif
-#if defined(CONFIG_NX823)
- unsigned char bi_sernum[8];
-#endif
-#if defined(CONFIG_4xx)
-#if defined(CONFIG_440GX)
- int bi_phynum[4]; /* Determines phy mapping */
- int bi_phymode[4]; /* Determines phy mode */
-#elif defined(CONFIG_405EP) || defined(CONFIG_440)
- int bi_phynum[2]; /* Determines phy mapping */
- int bi_phymode[2]; /* Determines phy mode */
-#else
- int bi_phynum[1]; /* Determines phy mapping */
- int bi_phymode[1]; /* Determines phy mode */
-#endif
-#endif /* defined(CONFIG_4xx) */
-} bd_t;
-
-#endif /* __ASSEMBLY__ */
#endif /* __BAREBOX_H__ */
--
1.7.10
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
prev parent reply other threads:[~2012-04-15 14:57 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-15 14:57 [PATCH] ppc cleanup Sascha Hauer
2012-04-15 14:57 ` [PATCH 1/2] ppc: remove unused init_board_data function Sascha Hauer
2012-04-15 14:57 ` Sascha Hauer [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1334501834-32001-3-git-send-email-s.hauer@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox