* [PATCH 0/2] Very minimal support S5PV210 board (Tiny210)
@ 2012-07-02 15:53 Alexey Galakhov
2012-07-02 15:53 ` [PATCH 1/2] S5P DRAM support Alexey Galakhov
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Alexey Galakhov @ 2012-07-02 15:53 UTC (permalink / raw)
To: barebox; +Cc: Alexey Galakhov
This is the revised versions of patches appeared on the list some time ago.
It supports very minimal subset of Tiny210 functions. It is currently
bootable from SD card only.
Alexey Galakhov (2):
S5P DRAM support
Add FriendlyArm Tiny210 board (S5PV210)
arch/arm/Makefile | 1 +
arch/arm/boards/tiny210/Makefile | 1 +
arch/arm/boards/tiny210/config.h | 19 ++
arch/arm/boards/tiny210/lowlevel.c | 72 +++++
arch/arm/boards/tiny210/tiny210.c | 113 ++++++++
arch/arm/configs/tiny210_defconfig | 17 ++
arch/arm/mach-samsung/Kconfig | 20 +-
arch/arm/mach-samsung/Makefile | 2 +-
arch/arm/mach-samsung/include/mach/s3c-generic.h | 6 +
arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h | 3 +
arch/arm/mach-samsung/mem-s5pcxx.c | 320 +++++++++++++++++++++
11 files changed, 567 insertions(+), 7 deletions(-)
create mode 100644 arch/arm/boards/tiny210/Makefile
create mode 100644 arch/arm/boards/tiny210/config.h
create mode 100644 arch/arm/boards/tiny210/lowlevel.c
create mode 100644 arch/arm/boards/tiny210/tiny210.c
create mode 100644 arch/arm/configs/tiny210_defconfig
create mode 100644 arch/arm/mach-samsung/mem-s5pcxx.c
--
1.7.10
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH 1/2] S5P DRAM support 2012-07-02 15:53 [PATCH 0/2] Very minimal support S5PV210 board (Tiny210) Alexey Galakhov @ 2012-07-02 15:53 ` Alexey Galakhov 2012-07-02 15:53 ` [PATCH 2/2] Add FriendlyArm Tiny210 board (S5PV210) Alexey Galakhov 2012-07-04 6:51 ` [PATCH 0/2] Very minimal support S5PV210 board (Tiny210) Sascha Hauer 2 siblings, 0 replies; 6+ messages in thread From: Alexey Galakhov @ 2012-07-02 15:53 UTC (permalink / raw) To: barebox; +Cc: Alexey Galakhov Signed-off-by: Alexey Galakhov <agalakhov@gmail.com> --- arch/arm/mach-samsung/Makefile | 2 +- arch/arm/mach-samsung/include/mach/s3c-generic.h | 6 + arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h | 3 + arch/arm/mach-samsung/mem-s5pcxx.c | 320 +++++++++++++++++++++ 4 files changed, 330 insertions(+), 1 deletion(-) create mode 100644 arch/arm/mach-samsung/mem-s5pcxx.c diff --git a/arch/arm/mach-samsung/Makefile b/arch/arm/mach-samsung/Makefile index d7344c8..6020587 100644 --- a/arch/arm/mach-samsung/Makefile +++ b/arch/arm/mach-samsung/Makefile @@ -2,5 +2,5 @@ obj-y += s3c-timer.o generic.o obj-lowlevel-$(CONFIG_ARCH_S3C24xx) += lowlevel-s3c24x0.o obj-lowlevel-$(CONFIG_ARCH_S5PCxx) += lowlevel-s5pcxx.o obj-$(CONFIG_ARCH_S3C24xx) += gpio-s3c24x0.o s3c24xx-clocks.o mem-s3c24x0.o -obj-$(CONFIG_ARCH_S5PCxx) += gpio-s5pcxx.o clocks-s5pcxx.o +obj-$(CONFIG_ARCH_S5PCxx) += gpio-s5pcxx.o clocks-s5pcxx.o mem-s5pcxx.o obj-$(CONFIG_S3C_LOWLEVEL_INIT) += $(obj-lowlevel-y) diff --git a/arch/arm/mach-samsung/include/mach/s3c-generic.h b/arch/arm/mach-samsung/include/mach/s3c-generic.h index 11b083d..329c2b4 100644 --- a/arch/arm/mach-samsung/include/mach/s3c-generic.h +++ b/arch/arm/mach-samsung/include/mach/s3c-generic.h @@ -24,6 +24,8 @@ * MA 02111-1307 USA */ +#include <common.h> + uint32_t s3c_get_mpllclk(void); uint32_t s3c_get_upllclk(void); uint32_t s3c_get_fclk(void); @@ -40,4 +42,8 @@ void s3c24xx_disable_second_sdram_bank(void); #ifdef CONFIG_ARCH_S5PCxx void s5p_init_pll(void); +void s5p_init_dram_bank_lpddr(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16); +void s5p_init_dram_bank_lpddr2(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16); +void s5p_init_dram_bank_ddr2(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16); +uint32_t s5p_get_memory_size(void); #endif diff --git a/arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h b/arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h index cb05527..248f868 100644 --- a/arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h +++ b/arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h @@ -47,3 +47,6 @@ #define S3C_UART3_SIZE 0x400 #define S3C_UART_HAS_UBRDIVSLOT #define S3C_UART_HAS_UINTM + +#define S5P_DMC0_BASE 0xF0000000 +#define S5P_DMC1_BASE 0xF1400000 diff --git a/arch/arm/mach-samsung/mem-s5pcxx.c b/arch/arm/mach-samsung/mem-s5pcxx.c new file mode 100644 index 0000000..943f691 --- /dev/null +++ b/arch/arm/mach-samsung/mem-s5pcxx.c @@ -0,0 +1,320 @@ +/* + * Copyright (C) 2012 Alexey Galakhov + * + * Based on code from u-boot found somewhere on the web + * that seems to originate from Samsung + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <config.h> +#include <common.h> +#include <io.h> +#include <init.h> +#include <mach/s3c-generic.h> +#include <mach/s3c-iomap.h> + +#define S5P_DMC_CONCONTROL 0x00 +#define S5P_DMC_MEMCONTROL 0x04 +#define S5P_DMC_MEMCONFIG0 0x08 +#define S5P_DMC_MEMCONFIG1 0x0C +#define S5P_DMC_DIRECTCMD 0x10 +#define S5P_DMC_PRECHCONFIG 0x14 +#define S5P_DMC_PHYCONTROL0 0x18 +#define S5P_DMC_PHYCONTROL1 0x1C +#define S5P_DMC_PWRDNCONFIG 0x28 +#define S5P_DMC_TIMINGAREF 0x30 +#define S5P_DMC_TIMINGROW 0x34 +#define S5P_DMC_TIMINGDATA 0x38 +#define S5P_DMC_TIMINGPOWER 0x3C +#define S5P_DMC_PHYSTATUS 0x40 +#define S5P_DMC_MRSTATUS 0x54 + +/* DRAM commands */ +#define CMD(x) ((x) << 24) +#define BANK(x) ((x) << 16) +#define CHIP(x) ((x) << 20) +#define ADDR(x) (x) + +/** + * MR definition: + * 1 11 + * 2 1098 7654 3210 + * | | ^^^- burst length, 010=4, 011=8 + * | | ^- burst type 0=sequnential, 1=interleaved + * | ^^^-- CAS latency + * | ^----- test, 0=normal, 1=test + * |^---- DLL reset, 1=yes + * ^^^----- WR, 1=2, 2=3 etc. + * ^------- PD, 0=fast exit, 1=low power + * + * EMR1 definition: + * 1 11 + * 2 1098 7654 3210 + * | ^- DLL, 0=enable + * | ^-- output strength, 0=full, 1=reduced + * |^.. .^--- Rtt, 00=off, 01=75, 10=150, 11=50 Ohm + * | ^^ ^-- Posted CAS# AL, 0-6 + * ^^ ^------ OCD: 000=OCD exit, 111=enable defaults + * ^------ DQS#, 0=enable, 1=disable + * ^------- RDQS enable, 0=no, 1=yes + * ^-------- outputs, 0=enabled, 1=disabled + * + * EMR2 definition: + * bit 7 + * 1 1 + * 2 1098 7654 3210 + * ^-- SRT, 0=1x (0-85 deg.C), 1=2x (>85 deg.C) + * all other bits = 0 + * + * EMR3 definition: all bits 0 + */ + +#define MRS CMD(0x0) +#define PALL CMD(0x1) +#define PRE CMD(0x2) +#define DPD CMD(0x3) +#define REFS CMD(0x4) +#define REFA CMD(0x5) +#define CKEL CMD(0x6) +#define NOP CMD(0x7) +#define REFSX CMD(0x8) +#define MRR CMD(0x9) + +#define EMRS1 (MRS | BANK(1)) +#define EMRS2 (MRS | BANK(2)) +#define EMRS3 (MRS | BANK(3)) + +/* Burst is (1 << S5P_DRAM_BURST), i.e. S5P_DRAM_BURST=2 for burst 4 */ +#ifndef S5P_DRAM_BURST +/* (LP)DDR2 supports burst 4 only, make it default */ +# define S5P_DRAM_BURST 2 +#endif + +/** + * Initialization sequences for different kinds of DRAM + */ +#define dcmd(x) writel((x) | CHIP(chip), base + S5P_DMC_DIRECTCMD) + +static void __bare_init s5p_dram_init_seq_lpddr(phys_addr_t base, unsigned chip) +{ + const uint32_t emr = 0x400; /* DQS disable */ + const uint32_t mr = (((S5P_DRAM_WR) - 1) << 9) + | ((S5P_DRAM_CAS) << 4) + | (S5P_DRAM_BURST); + /* TODO this sequence is untested */ + dcmd(PALL); dcmd(REFA); dcmd(REFA); + dcmd(MRS | ADDR(mr)); + dcmd(EMRS1 | ADDR(emr)); +} + +static void __bare_init s5p_dram_init_seq_lpddr2(phys_addr_t base, unsigned chip) +{ + const uint32_t mr = (((S5P_DRAM_WR) - 1) << 9) + | ((S5P_DRAM_CAS) << 4) + | (S5P_DRAM_BURST); + /* TODO this sequence is untested */ + dcmd(NOP); + dcmd(MRS | ADDR(mr)); + do { + dcmd(MRR); + } while (readl(base + S5P_DMC_MRSTATUS) & 0x01); /* poll DAI */ +} + +static void __bare_init s5p_dram_init_seq_ddr2(phys_addr_t base, unsigned chip) +{ + const uint32_t emr = 0x400; /* DQS disable */ + const uint32_t mr = (((S5P_DRAM_WR) - 1) << 9) + | ((S5P_DRAM_CAS) << 4) + | (S5P_DRAM_BURST); + dcmd(NOP); + /* FIXME wait here? JEDEC recommends but nobody does */ + dcmd(PALL); dcmd(EMRS2); dcmd(EMRS3); + dcmd(EMRS1 | ADDR(emr)); /* DQS disable */ + dcmd(MRS | ADDR(mr | 0x100)); /* DLL reset */ + dcmd(PALL); dcmd(REFA); dcmd(REFA); + dcmd(MRS | ADDR(mr)); /* DLL no reset */ + dcmd(EMRS1 | ADDR(emr | 0x380)); /* OCD defaults */ + dcmd(EMRS1 | ADDR(emr)); /* OCD exit */ +} + +#undef dcmd + +static inline void __bare_init s5p_dram_start_dll(phys_addr_t base, uint32_t phycon1) +{ + uint32_t pc0 = 0x00101000; /* the only legal initial value */ + uint32_t lv; + + /* Init DLL */ + writel(pc0, base + S5P_DMC_PHYCONTROL0); + writel(phycon1, base + S5P_DMC_PHYCONTROL1); + + /* DLL on */ + pc0 |= 0x2; + writel(pc0, base + S5P_DMC_PHYCONTROL0); + + /* DLL start */ + pc0 |= 0x1; + writel(pc0, base + S5P_DMC_PHYCONTROL0); + + /* Find lock val */ + do { + lv = readl(base + S5P_DMC_PHYSTATUS); + } while ((lv & 0x7) != 0x7); + + lv >>= 6; + lv &= 0xff; /* ctrl_lock_value[9:2] - coarse */ + pc0 |= (lv << 24); /* ctrl_force */ + writel(pc0, base + S5P_DMC_PHYCONTROL0); /* force value locking */ +} + +static inline void __bare_init s5p_dram_setup(phys_addr_t base, uint32_t mc0, uint32_t mc1, + int bus16, uint32_t mcon) +{ + mcon |= (S5P_DRAM_BURST) << 20; + /* 16 or 32-bit bus ? */ + mcon |= bus16 ? 0x1000 : 0x2000; + if (mc1) + mcon |= 0x10000; /* two chips */ + + writel(mcon, base + S5P_DMC_MEMCONTROL); + + /* Set up memory layout */ + writel(mc0, base + S5P_DMC_MEMCONFIG0); + if (mc1) + writel(mc1, base + S5P_DMC_MEMCONFIG1); + + /* Open page precharge policy - reasonable defaults */ + writel(0xFF000000, base + S5P_DMC_PRECHCONFIG); + + /* Set up timings */ + writel(DMC_TIMING_AREF, base + S5P_DMC_TIMINGAREF); + writel(DMC_TIMING_ROW, base + S5P_DMC_TIMINGROW); + writel(DMC_TIMING_DATA, base + S5P_DMC_TIMINGDATA); + writel(DMC_TIMING_PWR, base + S5P_DMC_TIMINGPOWER); +} + +static inline void __bare_init s5p_dram_start(phys_addr_t base) +{ + /* Reasonable defaults and auto-refresh on */ + writel(0x0FFF1070, base + S5P_DMC_CONCONTROL); + /* Reasonable defaults */ + writel(0xFFFF00FF, base + S5P_DMC_PWRDNCONFIG); +} + +/* + * Initialize LPDDR memory bank + * TODO: this function is untested, see also init_seq function + */ +void __bare_init s5p_init_dram_bank_lpddr(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16) +{ + /* refcount 8, 90 deg. shift */ + s5p_dram_start_dll(base, 0x00000085); + /* LPDDR type */ + s5p_dram_setup(base, mc0, mc1, bus16, 0x100); + + /* Start-Up Commands */ + s5p_dram_init_seq_lpddr(base, 0); + if (mc1) + s5p_dram_init_seq_lpddr(base, 1); + + s5p_dram_start(base); +} + +/* + * Initialize LPDDR2 memory bank + * TODO: this function is untested, see also init_seq function + */ +void __bare_init s5p_init_dram_bank_lpddr2(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16) +{ + /* refcount 8, 90 deg. shift */ + s5p_dram_start_dll(base, 0x00000085); + /* LPDDR2 type */ + s5p_dram_setup(base, mc0, mc1, bus16, 0x200); + + /* Start-Up Commands */ + s5p_dram_init_seq_lpddr2(base, 0); + if (mc1) + s5p_dram_init_seq_lpddr2(base, 1); + + s5p_dram_start(base); +} + +/* + * Initialize DDR2 memory bank + */ +void __bare_init s5p_init_dram_bank_ddr2(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16) +{ + /* refcount 8, 180 deg. shift */ + s5p_dram_start_dll(base, 0x00000086); + /* DDR2 type */ + s5p_dram_setup(base, mc0, mc1, bus16, 0x400); + + /* Start-Up Commands */ + s5p_dram_init_seq_ddr2(base, 0); + if (mc1) + s5p_dram_init_seq_ddr2(base, 1); + + s5p_dram_start(base); +} + + +#define BANK_ENABLED(base) (readl((base) + S5P_DMC_PHYCONTROL0) & 1) +#define NUM_EXTRA_CHIPS(base) ((readl((base) + S5P_DMC_MEMCONTROL) >> 16) & 0xF) + +#define BANK_START(x) ((x) & 0xFF000000) +#define BANK_END(x) (BANK_START(x) | ~(((x) & 0x00FF0000) << 8)) +#define BANK_LEN(x) (BANK_END(x) - BANK_START(x) + 1) + +static inline void sortswap(uint32_t *x, uint32_t *y) +{ + if (*y < *x) { + *x ^= *y; + *y ^= *x; + *x ^= *y; + } +} + +uint32_t s5p_get_memory_size(void) +{ + int i; + uint32_t len; + uint32_t mc[4] = { 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF }; + /* Read MEMCONFIG registers */ + if (BANK_ENABLED(S5P_DMC0_BASE)) { + mc[0] = readl(S5P_DMC0_BASE + S5P_DMC_MEMCONFIG0); + if (NUM_EXTRA_CHIPS(S5P_DMC0_BASE) > 0) + mc[1] = readl(S5P_DMC0_BASE + S5P_DMC_MEMCONFIG1); + } + if (BANK_ENABLED(S5P_DMC1_BASE)) { + mc[2] = readl(S5P_DMC1_BASE + S5P_DMC_MEMCONFIG0); + if (NUM_EXTRA_CHIPS(S5P_DMC1_BASE) > 0) + mc[3] = readl(S5P_DMC1_BASE + S5P_DMC_MEMCONFIG1); + } + /* Sort using a sorting network */ + sortswap(mc + 0, mc + 2); + sortswap(mc + 1, mc + 3); + sortswap(mc + 0, mc + 1); + sortswap(mc + 2, mc + 3); + sortswap(mc + 1, mc + 2); + /* Is at least one chip enabled? */ + if (mc[0] == 0xFFFFFFFF) + return 0; + /* Determine maximum continuous region at start */ + len = BANK_LEN(mc[0]); + for (i = 1; i < 4; ++i) { + if (BANK_START(mc[i]) == BANK_END(mc[i - 1]) + 1) + len += BANK_LEN(mc[i]); + else + break; + } + return len; +} -- 1.7.10 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/2] Add FriendlyArm Tiny210 board (S5PV210) 2012-07-02 15:53 [PATCH 0/2] Very minimal support S5PV210 board (Tiny210) Alexey Galakhov 2012-07-02 15:53 ` [PATCH 1/2] S5P DRAM support Alexey Galakhov @ 2012-07-02 15:53 ` Alexey Galakhov 2012-07-04 6:51 ` [PATCH 0/2] Very minimal support S5PV210 board (Tiny210) Sascha Hauer 2 siblings, 0 replies; 6+ messages in thread From: Alexey Galakhov @ 2012-07-02 15:53 UTC (permalink / raw) To: barebox; +Cc: Alexey Galakhov Signed-off-by: Alexey Galakhov <agalakhov@gmail.com> --- arch/arm/Makefile | 1 + arch/arm/boards/tiny210/Makefile | 1 + arch/arm/boards/tiny210/config.h | 19 ++++++ arch/arm/boards/tiny210/lowlevel.c | 72 +++++++++++++++++++++++ arch/arm/boards/tiny210/tiny210.c | 113 ++++++++++++++++++++++++++++++++++++ arch/arm/configs/tiny210_defconfig | 17 ++++++ arch/arm/mach-samsung/Kconfig | 20 +++++-- 7 files changed, 237 insertions(+), 6 deletions(-) create mode 100644 arch/arm/boards/tiny210/Makefile create mode 100644 arch/arm/boards/tiny210/config.h create mode 100644 arch/arm/boards/tiny210/lowlevel.c create mode 100644 arch/arm/boards/tiny210/tiny210.c create mode 100644 arch/arm/configs/tiny210_defconfig diff --git a/arch/arm/Makefile b/arch/arm/Makefile index 1225df7..89cd1cb 100644 --- a/arch/arm/Makefile +++ b/arch/arm/Makefile @@ -137,6 +137,7 @@ board-$(CONFIG_MACH_TX51) := karo-tx51 board-$(CONFIG_MACH_MX6Q_ARM2) := freescale-mx6-arm2 board-$(CONFIG_MACH_TOSHIBA_AC100) := toshiba-ac100 board-$(CONFIG_MACH_CCMX51) := ccxmx51 +board-$(CONFIG_MACH_TINY210) := tiny210 machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y)) diff --git a/arch/arm/boards/tiny210/Makefile b/arch/arm/boards/tiny210/Makefile new file mode 100644 index 0000000..9c38e60 --- /dev/null +++ b/arch/arm/boards/tiny210/Makefile @@ -0,0 +1 @@ +obj-y += tiny210.o lowlevel.o diff --git a/arch/arm/boards/tiny210/config.h b/arch/arm/boards/tiny210/config.h new file mode 100644 index 0000000..86aedf0 --- /dev/null +++ b/arch/arm/boards/tiny210/config.h @@ -0,0 +1,19 @@ +#define S5PCXX_CLOCK_REFERENCE 24000000 + +#define set_pll(mdiv, pdiv, sdiv) (1<<31 | mdiv<<16 | pdiv<<8 | sdiv) + +#define BOARD_APLL_VAL set_pll(0x7d, 0x3, 0x1) +#define BOARD_MPLL_VAL set_pll(0x29b, 0xc, 0x1) +#define BOARD_EPLL_VAL set_pll(0x60, 0x6, 0x2) +#define BOARD_VPLL_VAL set_pll(0x6c, 0x6, 0x3) + +#define BOARD_CLK_DIV0_MASK 0xFFFFFFFF +#define BOARD_CLK_DIV0_VAL 0x14131440 +#define BOARD_APLL_LOCKTIME 0x2cf + +#define S5P_DRAM_WR 3 +#define S5P_DRAM_CAS 4 +#define DMC_TIMING_AREF 0x00000618 +#define DMC_TIMING_ROW 0x2B34438A +#define DMC_TIMING_DATA 0x24240000 +#define DMC_TIMING_PWR 0x0BDC0343 diff --git a/arch/arm/boards/tiny210/lowlevel.c b/arch/arm/boards/tiny210/lowlevel.c new file mode 100644 index 0000000..19739d8 --- /dev/null +++ b/arch/arm/boards/tiny210/lowlevel.c @@ -0,0 +1,72 @@ +/* + * Copyright (C) 2012 Alexey Galakhov + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> +#include <common.h> +#include <init.h> +#include <io.h> +#include <asm/barebox-arm.h> +#include <asm/sections.h> +#include <mach/s3c-iomap.h> +#include <mach/s3c-clocks.h> +#include <mach/s3c-generic.h> + +/* + * iROM boot from MMC + * TODO: replace this by native boot + */ + +#define ADDR_V210_SDMMC_BASE 0xD0037488 +#define ADDR_CopySDMMCtoMem 0xD0037F98 + +int __bare_init s5p_irom_load_mmc(void *dest, uint32_t start_block, uint16_t block_count) +{ + typedef uint32_t (*func_t) (int32_t, uint32_t, uint16_t, uint32_t*, int8_t); + uint32_t chbase = readl(ADDR_V210_SDMMC_BASE); + func_t func = (func_t)readl(ADDR_CopySDMMCtoMem); + int chan = (chbase - 0xEB000000) >> 20; + if (chan != 0 && chan != 2) + return 0; + return func(chan, start_block, block_count, (uint32_t*)dest, 0) ? 1 : 0; +} + + +void __bare_init board_init_lowlevel(void) +{ + uint32_t r; + +#ifdef CONFIG_S3C_PLL_INIT + s5p_init_pll(); +#endif + + if (get_pc() < 0xD0000000) /* Are we running from iRAM? */ + return; /* No, we don't. */ + + s5p_init_dram_bank_ddr2(S5P_DMC0_BASE, 0x20E00323, 0, 0); + + if (! s5p_irom_load_mmc((void*)TEXT_BASE - 16, 1, (barebox_image_size + 16 + 511) / 512)) + while (1) { } /* hang */ + + /* Jump to SDRAM */ + r = (unsigned)TEXT_BASE; + __asm__ __volatile__("mov pc, %0" : : "r"(r)); + while (1) { } /* hang */ +} diff --git a/arch/arm/boards/tiny210/tiny210.c b/arch/arm/boards/tiny210/tiny210.c new file mode 100644 index 0000000..1277649 --- /dev/null +++ b/arch/arm/boards/tiny210/tiny210.c @@ -0,0 +1,113 @@ +/* + * Copyright (C) 2012 Alexey Galakhov + * Based on Mini6410 code by Juergen Beisert + * + * Copyright (C) 2012 Juergen Beisert, Pengutronix + * + * In some ways inspired by code + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * (C) Copyright 2002 + * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <common.h> +#include <driver.h> +#include <init.h> +#include <sizes.h> +#include <generated/mach-types.h> +#include <dm9000.h> +#include <gpio.h> +#include <led.h> +#include <io.h> +#include <nand.h> +#include <asm/armlinux.h> +#include <mach/s3c-iomap.h> +#include <mach/s3c-clocks.h> +#include <mach/s3c-generic.h> + + +static const unsigned pin_usage[] = { + /* TODO */ +}; + +static struct gpio_led leds[] = { + { + .gpio = GPJ20, + .led = { + .name = "led1", + } + }, { + .gpio = GPJ21, + .led = { + .name = "led2", + } + }, { + .gpio = GPJ22, + .led = { + .name = "led3", + } + }, { + .gpio = GPJ23, + .led = { + .name = "led4", + } + } +}; + +static int tiny210_mem_init(void) +{ + arm_add_mem_device("ram0", S3C_SDRAM_BASE, s5p_get_memory_size()); + return 0; +} +mem_initcall(tiny210_mem_init); + +static int tiny210_console_init(void) +{ + /* + * configure the UART1 right now, as barebox will + * start to send data immediately + */ + s3c_gpio_mode(GPA00_RXD0 | ENABLE_PU); + s3c_gpio_mode(GPA01_TXD0); + s3c_gpio_mode(GPA02_NCTS0 | ENABLE_PU); + s3c_gpio_mode(GPA03_NRTS0); + + add_generic_device("s3c_serial", -1, NULL, + S3C_UART1_BASE, S3C_UART1_SIZE, + IORESOURCE_MEM, NULL); + return 0; +} +console_initcall(tiny210_console_init); + +static int tiny210_devices_init(void) +{ + int i; + for (i = 0; i < ARRAY_SIZE(pin_usage); i++) + s3c_gpio_mode(pin_usage[i]); + + for (i = 0; i < ARRAY_SIZE(leds); i++) { + leds[i].active_low = 1; + gpio_direction_output(leds[i].gpio, leds[i].active_low); + led_gpio_register(&leds[i]); + } + + armlinux_set_bootparams((void*)S3C_SDRAM_BASE + 0x100); + armlinux_set_architecture(MACH_TYPE_MINI210); + + return 0; +} +device_initcall(tiny210_devices_init); diff --git a/arch/arm/configs/tiny210_defconfig b/arch/arm/configs/tiny210_defconfig new file mode 100644 index 0000000..e9708bf --- /dev/null +++ b/arch/arm/configs/tiny210_defconfig @@ -0,0 +1,17 @@ +CONFIG_ARCH_S5PCxx=y +CONFIG_CPU_V7=y +CONFIG_CPU_32v7=y +CONFIG_BOARDINFO="Tiny 210" +CONFIG_ARCH_BAREBOX_MAX_BARE_INIT_SIZE=0x1ff0 +CONFIG_ARCH_SAMSUNG=y +CONFIG_CPU_S5PV210=y +CONFIG_MACH_TINY210=y +CONFIG_S3C_LOWLEVEL_INIT=y +CONFIG_S3C_PLL_INIT=y +CONFIG_S3C_SDRAM_INIT=y +CONFIG_CMD_LED=y +CONFIG_CMD_LED_TRIGGER=y +CONFIG_DRIVER_SERIAL_S3C=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_LED_TRIGGERS=y diff --git a/arch/arm/mach-samsung/Kconfig b/arch/arm/mach-samsung/Kconfig index c60f5ed..90cda30 100644 --- a/arch/arm/mach-samsung/Kconfig +++ b/arch/arm/mach-samsung/Kconfig @@ -8,11 +8,13 @@ config ARCH_TEXT_BASE default 0x31fc0000 if MACH_MINI2440 default 0x31fc0000 if MACH_A9M2440 default 0x31fc0000 if MACH_A9M2410 + default 0x23e00000 if MACH_TINY210 config BOARDINFO default "Mini 2440" if MACH_MINI2440 default "Digi A9M2440" if MACH_A9M2440 default "Digi A9M2410" if MACH_A9M2410 + default "Tiny 210" if MACH_TINY210 config ARCH_BAREBOX_MAX_BARE_INIT_SIZE hex @@ -92,12 +94,18 @@ config CPU_S5PC110 config CPU_S5PV210 bool -#choice -# -# prompt "S5PCxx board type" -# -# -#endchoice +choice + + prompt "S5PCxx board type" + +config MACH_TINY210 + bool "Tiny 210" + select CPU_S5PV210 + select MACH_HAS_LOWLEVEL_INIT + select MACH_DO_LOWLEVEL_INIT + select S3C_SDRAM_INIT + +endchoice endif -- 1.7.10 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/2] Very minimal support S5PV210 board (Tiny210) 2012-07-02 15:53 [PATCH 0/2] Very minimal support S5PV210 board (Tiny210) Alexey Galakhov 2012-07-02 15:53 ` [PATCH 1/2] S5P DRAM support Alexey Galakhov 2012-07-02 15:53 ` [PATCH 2/2] Add FriendlyArm Tiny210 board (S5PV210) Alexey Galakhov @ 2012-07-04 6:51 ` Sascha Hauer 2 siblings, 0 replies; 6+ messages in thread From: Sascha Hauer @ 2012-07-04 6:51 UTC (permalink / raw) To: Alexey Galakhov; +Cc: barebox On Mon, Jul 02, 2012 at 09:53:38PM +0600, Alexey Galakhov wrote: > This is the revised versions of patches appeared on the list some time ago. > It supports very minimal subset of Tiny210 functions. It is currently > bootable from SD card only. Applied, thanks Sascha > > Alexey Galakhov (2): > S5P DRAM support > Add FriendlyArm Tiny210 board (S5PV210) > > arch/arm/Makefile | 1 + > arch/arm/boards/tiny210/Makefile | 1 + > arch/arm/boards/tiny210/config.h | 19 ++ > arch/arm/boards/tiny210/lowlevel.c | 72 +++++ > arch/arm/boards/tiny210/tiny210.c | 113 ++++++++ > arch/arm/configs/tiny210_defconfig | 17 ++ > arch/arm/mach-samsung/Kconfig | 20 +- > arch/arm/mach-samsung/Makefile | 2 +- > arch/arm/mach-samsung/include/mach/s3c-generic.h | 6 + > arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h | 3 + > arch/arm/mach-samsung/mem-s5pcxx.c | 320 +++++++++++++++++++++ > 11 files changed, 567 insertions(+), 7 deletions(-) > create mode 100644 arch/arm/boards/tiny210/Makefile > create mode 100644 arch/arm/boards/tiny210/config.h > create mode 100644 arch/arm/boards/tiny210/lowlevel.c > create mode 100644 arch/arm/boards/tiny210/tiny210.c > create mode 100644 arch/arm/configs/tiny210_defconfig > create mode 100644 arch/arm/mach-samsung/mem-s5pcxx.c > > -- > 1.7.10 > > > _______________________________________________ > barebox mailing list > barebox@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/barebox > -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 6+ messages in thread
* [RFC:PATCH 0/2] Revised S5PV210 DRAM support @ 2012-05-24 13:27 Alexey Galakhov 2012-05-24 13:27 ` [PATCH 1/2] S5P " Alexey Galakhov 0 siblings, 1 reply; 6+ messages in thread From: Alexey Galakhov @ 2012-05-24 13:27 UTC (permalink / raw) To: barebox; +Cc: Alexey Galakhov This is S5PV210 DRAM support without #ifdefs. Any comments are welcome. Alexey Galakhov (2): S5P DRAM support Add FriendlyArm Tiny210 board (S5PV210) arch/arm/Makefile | 1 + arch/arm/boards/tiny210/Makefile | 1 + arch/arm/boards/tiny210/config.h | 19 ++ arch/arm/boards/tiny210/lowlevel.c | 76 +++++ arch/arm/boards/tiny210/tiny210.c | 113 ++++++++ arch/arm/configs/tiny210_defconfig | 17 ++ arch/arm/mach-samsung/Kconfig | 7 + arch/arm/mach-samsung/Makefile | 2 +- arch/arm/mach-samsung/include/mach/s3c-generic.h | 6 + arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h | 3 + arch/arm/mach-samsung/mem-s5pcxx.c | 319 +++++++++++++++++++++ 11 files changed, 563 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boards/tiny210/Makefile create mode 100644 arch/arm/boards/tiny210/config.h create mode 100644 arch/arm/boards/tiny210/lowlevel.c create mode 100644 arch/arm/boards/tiny210/tiny210.c create mode 100644 arch/arm/configs/tiny210_defconfig create mode 100644 arch/arm/mach-samsung/mem-s5pcxx.c -- 1.7.10 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 1/2] S5P DRAM support 2012-05-24 13:27 [RFC:PATCH 0/2] Revised S5PV210 DRAM support Alexey Galakhov @ 2012-05-24 13:27 ` Alexey Galakhov 2012-05-24 20:13 ` Sascha Hauer 0 siblings, 1 reply; 6+ messages in thread From: Alexey Galakhov @ 2012-05-24 13:27 UTC (permalink / raw) To: barebox; +Cc: Alexey Galakhov Signed-off-by: Alexey Galakhov <agalakhov@gmail.com> --- arch/arm/mach-samsung/Makefile | 2 +- arch/arm/mach-samsung/include/mach/s3c-generic.h | 6 + arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h | 3 + arch/arm/mach-samsung/mem-s5pcxx.c | 319 +++++++++++++++++++++ 4 files changed, 329 insertions(+), 1 deletion(-) create mode 100644 arch/arm/mach-samsung/mem-s5pcxx.c diff --git a/arch/arm/mach-samsung/Makefile b/arch/arm/mach-samsung/Makefile index d7344c8..6020587 100644 --- a/arch/arm/mach-samsung/Makefile +++ b/arch/arm/mach-samsung/Makefile @@ -2,5 +2,5 @@ obj-y += s3c-timer.o generic.o obj-lowlevel-$(CONFIG_ARCH_S3C24xx) += lowlevel-s3c24x0.o obj-lowlevel-$(CONFIG_ARCH_S5PCxx) += lowlevel-s5pcxx.o obj-$(CONFIG_ARCH_S3C24xx) += gpio-s3c24x0.o s3c24xx-clocks.o mem-s3c24x0.o -obj-$(CONFIG_ARCH_S5PCxx) += gpio-s5pcxx.o clocks-s5pcxx.o +obj-$(CONFIG_ARCH_S5PCxx) += gpio-s5pcxx.o clocks-s5pcxx.o mem-s5pcxx.o obj-$(CONFIG_S3C_LOWLEVEL_INIT) += $(obj-lowlevel-y) diff --git a/arch/arm/mach-samsung/include/mach/s3c-generic.h b/arch/arm/mach-samsung/include/mach/s3c-generic.h index 11b083d..329c2b4 100644 --- a/arch/arm/mach-samsung/include/mach/s3c-generic.h +++ b/arch/arm/mach-samsung/include/mach/s3c-generic.h @@ -24,6 +24,8 @@ * MA 02111-1307 USA */ +#include <common.h> + uint32_t s3c_get_mpllclk(void); uint32_t s3c_get_upllclk(void); uint32_t s3c_get_fclk(void); @@ -40,4 +42,8 @@ void s3c24xx_disable_second_sdram_bank(void); #ifdef CONFIG_ARCH_S5PCxx void s5p_init_pll(void); +void s5p_init_dram_bank_lpddr(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16); +void s5p_init_dram_bank_lpddr2(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16); +void s5p_init_dram_bank_ddr2(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16); +uint32_t s5p_get_memory_size(void); #endif diff --git a/arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h b/arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h index cb05527..248f868 100644 --- a/arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h +++ b/arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h @@ -47,3 +47,6 @@ #define S3C_UART3_SIZE 0x400 #define S3C_UART_HAS_UBRDIVSLOT #define S3C_UART_HAS_UINTM + +#define S5P_DMC0_BASE 0xF0000000 +#define S5P_DMC1_BASE 0xF1400000 diff --git a/arch/arm/mach-samsung/mem-s5pcxx.c b/arch/arm/mach-samsung/mem-s5pcxx.c new file mode 100644 index 0000000..b240333 --- /dev/null +++ b/arch/arm/mach-samsung/mem-s5pcxx.c @@ -0,0 +1,319 @@ +/* + * Copyright (C) 2012 Alexey Galakhov + * + * Based on code from u-boot found somewhere on the web + * that seems to originate from Samsung + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <config.h> +#include <common.h> +#include <io.h> +#include <init.h> +#include <mach/s3c-generic.h> +#include <mach/s3c-iomap.h> + +#define S5P_DMC_CONCONTROL 0x00 +#define S5P_DMC_MEMCONTROL 0x04 +#define S5P_DMC_MEMCONFIG0 0x08 +#define S5P_DMC_MEMCONFIG1 0x0C +#define S5P_DMC_DIRECTCMD 0x10 +#define S5P_DMC_PRECHCONFIG 0x14 +#define S5P_DMC_PHYCONTROL0 0x18 +#define S5P_DMC_PHYCONTROL1 0x1C +#define S5P_DMC_PWRDNCONFIG 0x28 +#define S5P_DMC_TIMINGAREF 0x30 +#define S5P_DMC_TIMINGROW 0x34 +#define S5P_DMC_TIMINGDATA 0x38 +#define S5P_DMC_TIMINGPOWER 0x3C +#define S5P_DMC_PHYSTATUS 0x40 +#define S5P_DMC_MRSTATUS 0x54 + +/* DRAM commands */ +#define CMD(x) ((x) << 24) +#define BANK(x) ((x) << 16) +#define CHIP(x) ((x) << 20) +#define ADDR(x) (x) + +/** + * MR definition: + * 1 11 + * 2 1098 7654 3210 + * | | ^^^- burst length, 010=4, 011=8 + * | | ^- burst type 0=sequnential, 1=interleaved + * | ^^^-- CAS latency + * | ^----- test, 0=normal, 1=test + * |^---- DLL reset, 1=yes + * ^^^----- WR, 1=2, 2=3 etc. + * ^------- PD, 0=fast exit, 1=low power + * + * EMR1 definition: + * 1 11 + * 2 1098 7654 3210 + * | ^- DLL, 0=enable + * | ^-- output strength, 0=full, 1=reduced + * |^.. .^--- Rtt, 00=off, 01=75, 10=150, 11=50 Ohm + * | ^^ ^-- Posted CAS# AL, 0-6 + * ^^ ^------ OCD: 000=OCD exit, 111=enable defaults + * ^------ DQS#, 0=enable, 1=disable + * ^------- RDQS enable, 0=no, 1=yes + * ^-------- outputs, 0=enabled, 1=disabled + * + * EMR2 definition: + * bit 7 + * 1 1 + * 2 1098 7654 3210 + * ^-- SRT, 0=1x (0-85 deg.C), 1=2x (>85 deg.C) + * all other bits = 0 + * + * EMR3 definition: all bits 0 + */ + +#define MRS CMD(0x0) +#define PALL CMD(0x1) +#define PRE CMD(0x2) +#define DPD CMD(0x3) +#define REFS CMD(0x4) +#define REFA CMD(0x5) +#define CKEL CMD(0x6) +#define NOP CMD(0x7) +#define REFSX CMD(0x8) +#define MRR CMD(0x9) + +#define EMRS1 (MRS | BANK(1)) +#define EMRS2 (MRS | BANK(2)) +#define EMRS3 (MRS | BANK(3)) + +/* Burst is (1 << S5P_DRAM_BURST), i.e. S5P_DRAM_BURST=2 for burst 4 */ +#ifndef S5P_DRAM_BURST +/* (LP)DDR2 supports burst 4 only, make it default */ +# define S5P_DRAM_BURST 2 +#endif + +/** + * Initialization sequences for different kinds of DRAM + */ +#define dcmd(x) writel((x) | CHIP(chip), base + S5P_DMC_DIRECTCMD) + +static void __bare_init s5p_dram_init_seq_lpddr(phys_addr_t base, unsigned chip) +{ + const uint32_t emr = 0x400; /* DQS disable */ + const uint32_t mr = (((S5P_DRAM_WR) - 1) << 9) + | ((S5P_DRAM_CAS) << 4) + | (S5P_DRAM_BURST); + /* FIXME this sequence is untested */ + dcmd(PALL); dcmd(REFA); dcmd(REFA); + dcmd(MRS | ADDR(mr)); + dcmd(EMRS1 | ADDR(emr)); +} + +static void __bare_init s5p_dram_init_seq_lpddr2(phys_addr_t base, unsigned chip) +{ + const uint32_t mr = (((S5P_DRAM_WR) - 1) << 9) + | ((S5P_DRAM_CAS) << 4) + | (S5P_DRAM_BURST); + /* FIXME this sequence is untested */ + dcmd(NOP); + dcmd(MRS | ADDR(mr)); + do { + dcmd(MRR); + } while (readl(base + S5P_DMC_MRSTATUS) & 0x01); /* poll DAI */ +} + +static void __bare_init s5p_dram_init_seq_ddr2(phys_addr_t base, unsigned chip) +{ + const uint32_t emr = 0x400; /* DQS disable */ + const uint32_t mr = (((S5P_DRAM_WR) - 1) << 9) + | ((S5P_DRAM_CAS) << 4) + | (S5P_DRAM_BURST); + dcmd(NOP); + /* FIXME wait here? JEDEC recommends but nobody does */ + dcmd(PALL); dcmd(EMRS2); dcmd(EMRS3); + dcmd(EMRS1 | ADDR(emr)); /* DQS disable */ + dcmd(MRS | ADDR(mr | 0x100)); /* DLL reset */ + dcmd(PALL); dcmd(REFA); dcmd(REFA); + dcmd(MRS | ADDR(mr)); /* DLL no reset */ + dcmd(EMRS1 | ADDR(emr | 0x380)); /* OCD defaults */ + dcmd(EMRS1 | ADDR(emr)); /* OCD exit */ +} + +#undef dcmd + +static inline void __bare_init s5p_dram_start_dll(phys_addr_t base, uint32_t phycon1) +{ + uint32_t pc0 = 0x00101000; /* the only legal initial value */ + uint32_t lv; + + /* Init DLL */ + writel(pc0, base + S5P_DMC_PHYCONTROL0); + writel(phycon1, base + S5P_DMC_PHYCONTROL1); + writel(0x00000085, base + S5P_DMC_PHYCONTROL1); + + /* DLL on */ + pc0 |= 0x2; + writel(pc0, base + S5P_DMC_PHYCONTROL0); + + /* DLL start */ + pc0 |= 0x1; + writel(pc0, base + S5P_DMC_PHYCONTROL0); + + /* Find lock val */ + do { + lv = readl(base + S5P_DMC_PHYSTATUS); + } while ((lv & 0x7) != 0x7); + + lv >>= 6; + lv &= 0xff; /* ctrl_lock_value[9:2] - coarse */ + pc0 |= (lv << 24); /* ctrl_force */ + writel(pc0, base + S5P_DMC_PHYCONTROL0); /* force value locking */ +} + +static inline void __bare_init s5p_dram_setup(phys_addr_t base, uint32_t mc0, uint32_t mc1, + int bus16, uint32_t mcon) +{ + mcon |= (S5P_DRAM_BURST) << 20; + /* 16 or 32-bit bus ? */ + mcon |= bus16 ? 0x1000 : 0x2000; + if (mc1) + mcon |= 0x10000; /* two chips */ + + writel(mcon, base + S5P_DMC_MEMCONTROL); + + /* Set up memory layout */ + writel(mc0, base + S5P_DMC_MEMCONFIG0); + if (mc1) + writel(mc1, base + S5P_DMC_MEMCONFIG1); + + /* Open page precharge policy - reasonable defaults */ + writel(0xFF000000, base + S5P_DMC_PRECHCONFIG); + + /* Set up timings */ + writel(DMC_TIMING_AREF, base + S5P_DMC_TIMINGAREF); + writel(DMC_TIMING_ROW, base + S5P_DMC_TIMINGROW); + writel(DMC_TIMING_DATA, base + S5P_DMC_TIMINGDATA); + writel(DMC_TIMING_PWR, base + S5P_DMC_TIMINGPOWER); +} + +static inline void __bare_init s5p_dram_start(phys_addr_t base) +{ + /* Reasonable defaults and auto-refresh on */ + writel(0x0FFF1070, base + S5P_DMC_CONCONTROL); + /* Reasonable defaults */ + writel(0xFFFF00FF, base + S5P_DMC_PWRDNCONFIG); +} + +/* + * Initialize LPDDR memory bank + */ +void __bare_init s5p_init_dram_bank_lpddr(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16) +{ + /* refcount 8, 90 deg. shift */ + s5p_dram_start_dll(base, 0x00000085); + /* LPDDR type */ + s5p_dram_setup(base, mc0, mc1, bus16, 0x100); + + /* Start-Up Commands */ + s5p_dram_init_seq_lpddr(base, 0); + if (mc1) + s5p_dram_init_seq_lpddr(base, 1); + + s5p_dram_start(base); +} + +/* + * Initialize LPDDR2 memory bank + */ +void __bare_init s5p_init_dram_bank_lpddr2(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16) +{ + /* refcount 8, 90 deg. shift */ + s5p_dram_start_dll(base, 0x00000085); + /* LPDDR2 type */ + s5p_dram_setup(base, mc0, mc1, bus16, 0x200); + + /* Start-Up Commands */ + s5p_dram_init_seq_lpddr2(base, 0); + if (mc1) + s5p_dram_init_seq_lpddr2(base, 1); + + s5p_dram_start(base); +} + +/* + * Initialize DDR2 memory bank + */ +void __bare_init s5p_init_dram_bank_ddr2(phys_addr_t base, uint32_t mc0, uint32_t mc1, int bus16) +{ + /* refcount 8, 180 deg. shift */ + s5p_dram_start_dll(base, 0x00000086); + /* DDR2 type */ + s5p_dram_setup(base, mc0, mc1, bus16, 0x400); + + /* Start-Up Commands */ + s5p_dram_init_seq_ddr2(base, 0); + if (mc1) + s5p_dram_init_seq_ddr2(base, 1); + + s5p_dram_start(base); +} + + +#define BANK_ENABLED(base) (readl((base) + S5P_DMC_PHYCONTROL0) & 1) +#define NUM_EXTRA_CHIPS(base) ((readl((base) + S5P_DMC_MEMCONTROL) >> 16) & 0xF) + +#define BANK_START(x) ((x) & 0xFF000000) +#define BANK_END(x) (BANK_START(x) | ~(((x) & 0x00FF0000) << 8)) +#define BANK_LEN(x) (BANK_END(x) - BANK_START(x) + 1) + +static inline void sortswap(uint32_t *x, uint32_t *y) +{ + if (*y < *x) { + *x ^= *y; + *y ^= *x; + *x ^= *y; + } +} + +uint32_t s5p_get_memory_size(void) +{ + int i; + uint32_t len; + uint32_t mc[4] = { 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF, 0xFFFFFFFF }; + /* Read MEMCONFIG registers */ + if (BANK_ENABLED(S5P_DMC0_BASE)) { + mc[0] = readl(S5P_DMC0_BASE + S5P_DMC_MEMCONFIG0); + if (NUM_EXTRA_CHIPS(S5P_DMC0_BASE) > 0) + mc[1] = readl(S5P_DMC0_BASE + S5P_DMC_MEMCONFIG1); + } + if (BANK_ENABLED(S5P_DMC1_BASE)) { + mc[2] = readl(S5P_DMC1_BASE + S5P_DMC_MEMCONFIG0); + if (NUM_EXTRA_CHIPS(S5P_DMC1_BASE) > 0) + mc[3] = readl(S5P_DMC1_BASE + S5P_DMC_MEMCONFIG1); + } + /* Sort using a sorting network */ + sortswap(mc + 0, mc + 2); + sortswap(mc + 1, mc + 3); + sortswap(mc + 0, mc + 1); + sortswap(mc + 2, mc + 3); + sortswap(mc + 1, mc + 2); + /* Is at least one chip enabled? */ + if (mc[0] == 0xFFFFFFFF) + return 0; + /* Determine maximum continuous region at start */ + len = BANK_LEN(mc[0]); + for (i = 1; i < 4; ++i) { + if (BANK_START(mc[i]) == BANK_END(mc[i - 1]) + 1) + len += BANK_LEN(mc[i]); + else + break; + } + return len; +} -- 1.7.10 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 1/2] S5P DRAM support 2012-05-24 13:27 ` [PATCH 1/2] S5P " Alexey Galakhov @ 2012-05-24 20:13 ` Sascha Hauer 0 siblings, 0 replies; 6+ messages in thread From: Sascha Hauer @ 2012-05-24 20:13 UTC (permalink / raw) To: Alexey Galakhov; +Cc: barebox On Thu, May 24, 2012 at 07:27:44PM +0600, Alexey Galakhov wrote: > Signed-off-by: Alexey Galakhov <agalakhov@gmail.com> > --- > arch/arm/mach-samsung/Makefile | 2 +- > arch/arm/mach-samsung/include/mach/s3c-generic.h | 6 + > arch/arm/mach-samsung/include/mach/s5pcxx-iomap.h | 3 + > arch/arm/mach-samsung/mem-s5pcxx.c | 319 +++++++++++++++++++++ > 4 files changed, 329 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/mach-samsung/mem-s5pcxx.c > > + > +static void __bare_init s5p_dram_init_seq_lpddr(phys_addr_t base, unsigned chip) > +{ > + const uint32_t emr = 0x400; /* DQS disable */ > + const uint32_t mr = (((S5P_DRAM_WR) - 1) << 9) > + | ((S5P_DRAM_CAS) << 4) > + | (S5P_DRAM_BURST); > + /* FIXME this sequence is untested */ Maybe add these comments to the exported functions rather than in the helpers? It would be more prominent and people would see it more easily. Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2012-07-04 6:51 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2012-07-02 15:53 [PATCH 0/2] Very minimal support S5PV210 board (Tiny210) Alexey Galakhov 2012-07-02 15:53 ` [PATCH 1/2] S5P DRAM support Alexey Galakhov 2012-07-02 15:53 ` [PATCH 2/2] Add FriendlyArm Tiny210 board (S5PV210) Alexey Galakhov 2012-07-04 6:51 ` [PATCH 0/2] Very minimal support S5PV210 board (Tiny210) Sascha Hauer -- strict thread matches above, loose matches on Subject: below -- 2012-05-24 13:27 [RFC:PATCH 0/2] Revised S5PV210 DRAM support Alexey Galakhov 2012-05-24 13:27 ` [PATCH 1/2] S5P " Alexey Galakhov 2012-05-24 20:13 ` Sascha Hauer
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox