* [PATCH 0/3] i2c: add at24 eeprom support
@ 2012-11-03 20:56 Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 1/3] import log2 support from linux Jean-Christophe PLAGNIOL-VILLARD
2012-11-12 7:38 ` [PATCH 0/3] i2c: add at24 eeprom support Sascha Hauer
0 siblings, 2 replies; 5+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-11-03 20:56 UTC (permalink / raw)
To: barebox
HI,
this patch serie add the at24 eeprom support based on linux 3.6
the depends on the i2c prepare 1t24 support patch series
The following changes since commit 5526278ac77ecd7109c9c1bbc35d7c74875902e7:
i2c: add id_table support (2012-11-03 13:33:54 +0800)
are available in the git repository at:
git://git.jcrosoft.org/barebox.git delivery/at24
for you to fetch changes up to fe6968e20c39461df068d5cc15869012be4a3161:
eeprom: add at24 support (2012-11-03 13:46:50 +0800)
----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (3):
import log2 support from linux
add roundup and rounddown support
eeprom: add at24 support
drivers/eeprom/Kconfig | 19 ++++++++++
drivers/eeprom/Makefile | 1 +
drivers/eeprom/at24.c | 460 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
include/i2c/at24.h | 35 +++++++++++++++++++
include/linux/kernel.h | 15 ++++++++
include/linux/log2.h | 190 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
6 files changed, 720 insertions(+)
create mode 100644 drivers/eeprom/at24.c
create mode 100644 include/i2c/at24.h
create mode 100644 include/linux/log2.h
Best Regards,
J.
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/3] import log2 support from linux
2012-11-03 20:56 [PATCH 0/3] i2c: add at24 eeprom support Jean-Christophe PLAGNIOL-VILLARD
@ 2012-11-03 20:58 ` Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 2/3] add roundup and rounddown support Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 3/3] eeprom: add at24 support Jean-Christophe PLAGNIOL-VILLARD
2012-11-12 7:38 ` [PATCH 0/3] i2c: add at24 eeprom support Sascha Hauer
1 sibling, 2 replies; 5+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-11-03 20:58 UTC (permalink / raw)
To: barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
include/linux/log2.h | 190 ++++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 190 insertions(+)
create mode 100644 include/linux/log2.h
diff --git a/include/linux/log2.h b/include/linux/log2.h
new file mode 100644
index 0000000..389043a
--- /dev/null
+++ b/include/linux/log2.h
@@ -0,0 +1,190 @@
+/* Integer base 2 logarithm calculation
+ *
+ * Copyright (C) 2006 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef _LINUX_LOG2_H
+#define _LINUX_LOG2_H
+
+#include <linux/types.h>
+#include <linux/bitops.h>
+
+/*
+ * deal with unrepresentable constant logarithms
+ */
+extern __attribute__((const, noreturn))
+int ____ilog2_NaN(void);
+
+/*
+ * non-constant log of base 2 calculators
+ * - the arch may override these in asm/bitops.h if they can be implemented
+ * more efficiently than using fls() and fls64()
+ * - the arch is not required to handle n==0 if implementing the fallback
+ */
+#ifndef CONFIG_ARCH_HAS_ILOG2_U32
+static inline __attribute__((const))
+int __ilog2_u32(u32 n)
+{
+ return fls(n) - 1;
+}
+#endif
+
+#ifndef CONFIG_ARCH_HAS_ILOG2_U64
+static inline __attribute__((const))
+int __ilog2_u64(u64 n)
+{
+ return fls64(n) - 1;
+}
+#endif
+
+/*
+ * Determine whether some value is a power of two, where zero is
+ * *not* considered a power of two.
+ */
+
+static inline __attribute__((const))
+bool is_power_of_2(unsigned long n)
+{
+ return (n != 0 && ((n & (n - 1)) == 0));
+}
+
+/**
+ * ilog2 - log of base 2 of 32-bit or a 64-bit unsigned value
+ * @n - parameter
+ *
+ * constant-capable log of base 2 calculation
+ * - this can be used to initialise global variables from constant data, hence
+ * the massive ternary operator construction
+ *
+ * selects the appropriately-sized optimised version depending on sizeof(n)
+ */
+#define ilog2(n) \
+( \
+ __builtin_constant_p(n) ? ( \
+ (n) < 1 ? ____ilog2_NaN() : \
+ (n) & (1ULL << 63) ? 63 : \
+ (n) & (1ULL << 62) ? 62 : \
+ (n) & (1ULL << 61) ? 61 : \
+ (n) & (1ULL << 60) ? 60 : \
+ (n) & (1ULL << 59) ? 59 : \
+ (n) & (1ULL << 58) ? 58 : \
+ (n) & (1ULL << 57) ? 57 : \
+ (n) & (1ULL << 56) ? 56 : \
+ (n) & (1ULL << 55) ? 55 : \
+ (n) & (1ULL << 54) ? 54 : \
+ (n) & (1ULL << 53) ? 53 : \
+ (n) & (1ULL << 52) ? 52 : \
+ (n) & (1ULL << 51) ? 51 : \
+ (n) & (1ULL << 50) ? 50 : \
+ (n) & (1ULL << 49) ? 49 : \
+ (n) & (1ULL << 48) ? 48 : \
+ (n) & (1ULL << 47) ? 47 : \
+ (n) & (1ULL << 46) ? 46 : \
+ (n) & (1ULL << 45) ? 45 : \
+ (n) & (1ULL << 44) ? 44 : \
+ (n) & (1ULL << 43) ? 43 : \
+ (n) & (1ULL << 42) ? 42 : \
+ (n) & (1ULL << 41) ? 41 : \
+ (n) & (1ULL << 40) ? 40 : \
+ (n) & (1ULL << 39) ? 39 : \
+ (n) & (1ULL << 38) ? 38 : \
+ (n) & (1ULL << 37) ? 37 : \
+ (n) & (1ULL << 36) ? 36 : \
+ (n) & (1ULL << 35) ? 35 : \
+ (n) & (1ULL << 34) ? 34 : \
+ (n) & (1ULL << 33) ? 33 : \
+ (n) & (1ULL << 32) ? 32 : \
+ (n) & (1ULL << 31) ? 31 : \
+ (n) & (1ULL << 30) ? 30 : \
+ (n) & (1ULL << 29) ? 29 : \
+ (n) & (1ULL << 28) ? 28 : \
+ (n) & (1ULL << 27) ? 27 : \
+ (n) & (1ULL << 26) ? 26 : \
+ (n) & (1ULL << 25) ? 25 : \
+ (n) & (1ULL << 24) ? 24 : \
+ (n) & (1ULL << 23) ? 23 : \
+ (n) & (1ULL << 22) ? 22 : \
+ (n) & (1ULL << 21) ? 21 : \
+ (n) & (1ULL << 20) ? 20 : \
+ (n) & (1ULL << 19) ? 19 : \
+ (n) & (1ULL << 18) ? 18 : \
+ (n) & (1ULL << 17) ? 17 : \
+ (n) & (1ULL << 16) ? 16 : \
+ (n) & (1ULL << 15) ? 15 : \
+ (n) & (1ULL << 14) ? 14 : \
+ (n) & (1ULL << 13) ? 13 : \
+ (n) & (1ULL << 12) ? 12 : \
+ (n) & (1ULL << 11) ? 11 : \
+ (n) & (1ULL << 10) ? 10 : \
+ (n) & (1ULL << 9) ? 9 : \
+ (n) & (1ULL << 8) ? 8 : \
+ (n) & (1ULL << 7) ? 7 : \
+ (n) & (1ULL << 6) ? 6 : \
+ (n) & (1ULL << 5) ? 5 : \
+ (n) & (1ULL << 4) ? 4 : \
+ (n) & (1ULL << 3) ? 3 : \
+ (n) & (1ULL << 2) ? 2 : \
+ (n) & (1ULL << 1) ? 1 : \
+ (n) & (1ULL << 0) ? 0 : \
+ ____ilog2_NaN() \
+ ) : \
+ (sizeof(n) <= 4) ? \
+ __ilog2_u32(n) : \
+ __ilog2_u64(n) \
+ )
+
+/**
+ * roundup_pow_of_two - round the given value up to nearest power of two
+ * @n - parameter
+ *
+ * round the given value up to the nearest power of two
+ * - the result is undefined when n == 0
+ * - this can be used to initialise global variables from constant data
+ */
+#define roundup_pow_of_two(n) \
+( \
+ __builtin_constant_p(n) ? ( \
+ (n == 1) ? 1 : \
+ (1UL << (ilog2((n) - 1) + 1)) \
+ ) : \
+ __roundup_pow_of_two(n) \
+ )
+
+/**
+ * rounddown_pow_of_two - round the given value down to nearest power of two
+ * @n - parameter
+ *
+ * round the given value down to the nearest power of two
+ * - the result is undefined when n == 0
+ * - this can be used to initialise global variables from constant data
+ */
+#define rounddown_pow_of_two(n) \
+( \
+ __builtin_constant_p(n) ? ( \
+ (1UL << ilog2(n))) : \
+ __rounddown_pow_of_two(n) \
+ )
+
+/**
+ * order_base_2 - calculate the (rounded up) base 2 order of the argument
+ * @n: parameter
+ *
+ * The first few values calculated by this routine:
+ * ob2(0) = 0
+ * ob2(1) = 0
+ * ob2(2) = 1
+ * ob2(3) = 2
+ * ob2(4) = 2
+ * ob2(5) = 3
+ * ... and so on.
+ */
+
+#define order_base_2(n) ilog2(roundup_pow_of_two(n))
+
+#endif /* _LINUX_LOG2_H */
--
1.7.10.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 2/3] add roundup and rounddown support
2012-11-03 20:58 ` [PATCH 1/3] import log2 support from linux Jean-Christophe PLAGNIOL-VILLARD
@ 2012-11-03 20:58 ` Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 3/3] eeprom: add at24 support Jean-Christophe PLAGNIOL-VILLARD
1 sibling, 0 replies; 5+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-11-03 20:58 UTC (permalink / raw)
To: barebox
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
include/linux/kernel.h | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index e9e2f07..92c3391 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -90,5 +90,20 @@
__val = __val < __min ? __min: __val; \
__val > __max ? __max: __val; })
+
+/* The `const' in roundup() prevents gcc-3.3 from calling __divdi3 */
+#define roundup(x, y) ( \
+{ \
+ const typeof(y) __y = y; \
+ (((x) + (__y - 1)) / __y) * __y; \
+} \
+)
+#define rounddown(x, y) ( \
+{ \
+ typeof(x) __x = (x); \
+ __x - (__x % (y)); \
+} \
+)
+
#endif /* _LINUX_KERNEL_H */
--
1.7.10.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 3/3] eeprom: add at24 support
2012-11-03 20:58 ` [PATCH 1/3] import log2 support from linux Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 2/3] add roundup and rounddown support Jean-Christophe PLAGNIOL-VILLARD
@ 2012-11-03 20:58 ` Jean-Christophe PLAGNIOL-VILLARD
1 sibling, 0 replies; 5+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-11-03 20:58 UTC (permalink / raw)
To: barebox
This driver to get read/write support to most I2C EEPROMs,
after you configure the driver to know about each EEPROM on
your target board. Use these generic chip names, instead of
vendor-specific ones like at24c64 or 24lc02:
24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
Unless you like data loss puzzles, always be sure that any chip
you configure as a 24c32 (32 kbit) or larger is NOT really a
24c16 (16 kbit) or smaller, and vice versa. Marking the chip
as read-only won't help recover from this. Also, if your chip
has any software write-protect mechanism you may want to review the
code to make sure this driver won't turn it on by accident.
Based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
drivers/eeprom/Kconfig | 19 ++
drivers/eeprom/Makefile | 1 +
drivers/eeprom/at24.c | 460 +++++++++++++++++++++++++++++++++++++++++++++++
include/i2c/at24.h | 35 ++++
4 files changed, 515 insertions(+)
create mode 100644 drivers/eeprom/at24.c
create mode 100644 include/i2c/at24.h
diff --git a/drivers/eeprom/Kconfig b/drivers/eeprom/Kconfig
index a0b5489..ce9cfe7 100644
--- a/drivers/eeprom/Kconfig
+++ b/drivers/eeprom/Kconfig
@@ -8,4 +8,23 @@ config EEPROM_AT25
after you configure the board init code to know about each eeprom
on your target board.
+config EEPROM_AT24
+ bool "at24 based eeprom"
+ depends on I2C
+ help
+ Enable this driver to get read/write support to most I2C EEPROMs,
+ after you configure the driver to know about each EEPROM on
+ your target board. Use these generic chip names, instead of
+ vendor-specific ones like at24c64 or 24lc02:
+
+ 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
+ 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
+
+ Unless you like data loss puzzles, always be sure that any chip
+ you configure as a 24c32 (32 kbit) or larger is NOT really a
+ 24c16 (16 kbit) or smaller, and vice versa. Marking the chip
+ as read-only won't help recover from this. Also, if your chip
+ has any software write-protect mechanism you may want to review the
+ code to make sure this driver won't turn it on by accident.
+
endmenu
diff --git a/drivers/eeprom/Makefile b/drivers/eeprom/Makefile
index e323bd0..e287eb0 100644
--- a/drivers/eeprom/Makefile
+++ b/drivers/eeprom/Makefile
@@ -1 +1,2 @@
obj-$(CONFIG_EEPROM_AT25) += at25.o
+obj-$(CONFIG_EEPROM_AT24) += at24.o
diff --git a/drivers/eeprom/at24.c b/drivers/eeprom/at24.c
new file mode 100644
index 0000000..6f0133a
--- /dev/null
+++ b/drivers/eeprom/at24.c
@@ -0,0 +1,460 @@
+/*
+ * at24.c - handle most I2C EEPROMs
+ *
+ * Copyright (C) 2005-2007 David Brownell
+ * Copyright (C) 2008 Wolfram Sang, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <common.h>
+#include <init.h>
+#include <malloc.h>
+#include <clock.h>
+#include <driver.h>
+#include <xfuncs.h>
+#include <errno.h>
+#include <linux/math64.h>
+#include <linux/log2.h>
+#include <i2c/i2c.h>
+#include <i2c/at24.h>
+
+/*
+ * I2C EEPROMs from most vendors are inexpensive and mostly interchangeable.
+ * Differences between different vendor product lines (like Atmel AT24C or
+ * MicroChip 24LC, etc) won't much matter for typical read/write access.
+ * There are also I2C RAM chips, likewise interchangeable. One example
+ * would be the PCF8570, which acts like a 24c02 EEPROM (256 bytes).
+ *
+ * However, misconfiguration can lose data. "Set 16-bit memory address"
+ * to a part with 8-bit addressing will overwrite data. Writing with too
+ * big a page size also loses data. And it's not safe to assume that the
+ * conventional addresses 0x50..0x57 only hold eeproms; a PCF8563 RTC
+ * uses 0x51, for just one example.
+ *
+ * So this driver uses "new style" I2C driver binding, expecting to be
+ * told what devices exist. That may be in arch/X/mach-Y/board-Z.c or
+ * similar kernel-resident tables; or, configuration data coming from
+ * a bootloader.
+ *
+ * Other than binding model, current differences from "eeprom" driver are
+ * that this one handles write access and isn't restricted to 24c02 devices.
+ * It also handles larger devices (32 kbit and up) with two-byte addresses,
+ * which won't work on pure SMBus systems.
+ */
+
+struct at24_data {
+ struct at24_platform_data chip;
+
+ struct cdev cdev;
+ struct file_operations fops;
+
+ u8 *writebuf;
+ unsigned write_max;
+ unsigned num_addresses;
+
+ /*
+ * Some chips tie up multiple I2C addresses; dummy devices reserve
+ * them for us.
+ */
+ struct i2c_client *client[];
+};
+
+/*
+ * This parameter is to help this driver avoid blocking other drivers out
+ * of I2C for potentially troublesome amounts of time. With a 100 kHz I2C
+ * clock, one 256 byte read takes about 1/43 second which is excessive;
+ * but the 1/170 second it takes at 400 kHz may be quite reasonable; and
+ * at 1 MHz (Fm+) a 1/430 second delay could easily be invisible.
+ *
+ * This value is forced to be a power of two so that writes align on pages.
+ */
+static unsigned io_limit = 128;
+
+/*
+ * Specs often allow 5 msec for a page write, sometimes 20 msec;
+ * it's important to recover from write timeouts.
+ */
+static unsigned write_timeout = 25;
+
+#define AT24_SIZE_BYTELEN 5
+#define AT24_SIZE_FLAGS 8
+
+#define AT24_BITMASK(x) (BIT(x) - 1)
+
+/* create non-zero magic value for given eeprom parameters */
+#define AT24_DEVICE_MAGIC(_len, _flags) \
+ ((1 << AT24_SIZE_FLAGS | (_flags)) \
+ << AT24_SIZE_BYTELEN | ilog2(_len))
+
+static struct platform_device_id at24_ids[] = {
+ /* needs 8 addresses as A0-A2 are ignored */
+ { "24c00", AT24_DEVICE_MAGIC(128 / 8, AT24_FLAG_TAKE8ADDR) },
+ /* old variants can't be handled with this generic entry! */
+ { "24c01", AT24_DEVICE_MAGIC(1024 / 8, 0) },
+ { "24c02", AT24_DEVICE_MAGIC(2048 / 8, 0) },
+ /* spd is a 24c02 in memory DIMMs */
+ { "spd", AT24_DEVICE_MAGIC(2048 / 8,
+ AT24_FLAG_READONLY | AT24_FLAG_IRUGO) },
+ { "24c04", AT24_DEVICE_MAGIC(4096 / 8, 0) },
+ /* 24rf08 quirk is handled at i2c-core */
+ { "24c08", AT24_DEVICE_MAGIC(8192 / 8, 0) },
+ { "24c16", AT24_DEVICE_MAGIC(16384 / 8, 0) },
+ { "24c32", AT24_DEVICE_MAGIC(32768 / 8, AT24_FLAG_ADDR16) },
+ { "24c64", AT24_DEVICE_MAGIC(65536 / 8, AT24_FLAG_ADDR16) },
+ { "24c128", AT24_DEVICE_MAGIC(131072 / 8, AT24_FLAG_ADDR16) },
+ { "24c256", AT24_DEVICE_MAGIC(262144 / 8, AT24_FLAG_ADDR16) },
+ { "24c512", AT24_DEVICE_MAGIC(524288 / 8, AT24_FLAG_ADDR16) },
+ { "24c1024", AT24_DEVICE_MAGIC(1048576 / 8, AT24_FLAG_ADDR16) },
+ { "at24", 0 },
+ { /* END OF LIST */ }
+};
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * This routine supports chips which consume multiple I2C addresses. It
+ * computes the addressing information to be used for a given r/w request.
+ * Assumes that sanity checks for offset happened at sysfs-layer.
+ */
+static struct i2c_client *at24_translate_offset(struct at24_data *at24,
+ unsigned *offset)
+{
+ unsigned i;
+
+ if (at24->chip.flags & AT24_FLAG_ADDR16) {
+ i = *offset >> 16;
+ *offset &= 0xffff;
+ } else {
+ i = *offset >> 8;
+ *offset &= 0xff;
+ }
+
+ return at24->client[i];
+}
+
+static ssize_t at24_eeprom_read(struct at24_data *at24, char *buf,
+ unsigned offset, size_t count)
+{
+ struct i2c_msg msg[2];
+ u8 msgbuf[2];
+ struct i2c_client *client;
+ int status, i;
+ uint64_t start, read_time;
+
+ memset(msg, 0, sizeof(msg));
+
+ /*
+ * REVISIT some multi-address chips don't rollover page reads to
+ * the next slave address, so we may need to truncate the count.
+ * Those chips might need another quirk flag.
+ *
+ * If the real hardware used four adjacent 24c02 chips and that
+ * were misconfigured as one 24c08, that would be a similar effect:
+ * one "eeprom" file not four, but larger reads would fail when
+ * they crossed certain pages.
+ */
+
+ /*
+ * Slave address and byte offset derive from the offset. Always
+ * set the byte address; on a multi-master board, another master
+ * may have changed the chip's "current" address pointer.
+ */
+ client = at24_translate_offset(at24, &offset);
+
+ if (count > io_limit)
+ count = io_limit;
+
+ i = 0;
+ if (at24->chip.flags & AT24_FLAG_ADDR16)
+ msgbuf[i++] = offset >> 8;
+ msgbuf[i++] = offset;
+
+ msg[0].addr = client->addr;
+ msg[0].buf = msgbuf;
+ msg[0].len = i;
+
+ msg[1].addr = client->addr;
+ msg[1].flags = I2C_M_RD;
+ msg[1].buf = buf;
+ msg[1].len = count;
+
+ /*
+ * Reads fail if the previous write didn't complete yet. We may
+ * loop a few times until this one succeeds, waiting at least
+ * long enough for one entire page write to work.
+ */
+ start = get_time_ns();
+ do {
+ read_time = get_time_ns();
+ status = i2c_transfer(client->adapter, msg, 2);
+ if (status == 2)
+ status = count;
+ dev_dbg(&client->dev, "read %zu@%d --> %d (%llu)\n",
+ count, offset, status, read_time);
+
+ if (status == count)
+ return count;
+
+ /* REVISIT: at HZ=100, this is sloooow */
+ mdelay(1);
+ } while (!is_timeout(start, write_timeout * MSECOND));
+
+ return -ETIMEDOUT;
+}
+
+static ssize_t at24_read(struct at24_data *at24,
+ char *buf, loff_t off, size_t count)
+{
+ ssize_t retval = 0;
+
+ if (unlikely(!count))
+ return count;
+
+ /*
+ * Read data from chip, protecting against concurrent updates
+ * from this host, but not from other I2C masters.
+ */
+ while (count) {
+ ssize_t status;
+
+ status = at24_eeprom_read(at24, buf, off, count);
+ if (status <= 0) {
+ if (retval == 0)
+ retval = status;
+ break;
+ }
+ buf += status;
+ off += status;
+ count -= status;
+ retval += status;
+ }
+
+ return retval;
+}
+
+static ssize_t at24_cdev_read(struct cdev *cdev, void *buf, size_t count,
+ loff_t off, ulong flags)
+{
+ struct at24_data *at24 = cdev->priv;
+
+ return at24_read(at24, buf, off, count);
+}
+
+/*
+ * Note that if the hardware write-protect pin is pulled high, the whole
+ * chip is normally write protected. But there are plenty of product
+ * variants here, including OTP fuses and partial chip protect.
+ *
+ * We only use page mode writes; the alternative is sloooow. This routine
+ * writes at most one page.
+ */
+static ssize_t at24_eeprom_write(struct at24_data *at24, const char *buf,
+ unsigned offset, size_t count)
+{
+ struct i2c_client *client;
+ struct i2c_msg msg;
+ ssize_t status;
+ uint64_t start, write_time;
+ unsigned next_page;
+ int i = 0;
+
+ /* Get corresponding I2C address and adjust offset */
+ client = at24_translate_offset(at24, &offset);
+
+ /* write_max is at most a page */
+ if (count > at24->write_max)
+ count = at24->write_max;
+
+ /* Never roll over backwards, to the start of this page */
+ next_page = roundup(offset + 1, at24->chip.page_size);
+ if (offset + count > next_page)
+ count = next_page - offset;
+
+
+ msg.addr = client->addr;
+ msg.flags = 0;
+
+ /* msg.buf is u8 and casts will mask the values */
+ msg.buf = at24->writebuf;
+ if (at24->chip.flags & AT24_FLAG_ADDR16)
+ msg.buf[i++] = offset >> 8;
+
+ msg.buf[i++] = offset;
+ memcpy(&msg.buf[i], buf, count);
+ msg.len = i + count;
+
+ /*
+ * Writes fail if the previous one didn't complete yet. We may
+ * loop a few times until this one succeeds, waiting at least
+ * long enough for one entire page write to work.
+ */
+ start = get_time_ns();
+ do {
+ write_time = get_time_ns();
+ status = i2c_transfer(client->adapter, &msg, 1);
+ if (status == 1)
+ status = count;
+ dev_dbg(&client->dev, "write %zu@%d --> %zd (%llu)\n",
+ count, offset, status, write_time);
+
+ if (status == count)
+ return count;
+
+ /* REVISIT: at HZ=100, this is sloooow */
+ mdelay(1);
+ } while (!is_timeout(start, write_timeout * MSECOND));
+
+ return -ETIMEDOUT;
+}
+
+static ssize_t at24_write(struct at24_data *at24, const char *buf, loff_t off,
+ size_t count)
+{
+ ssize_t retval = 0;
+
+ if (unlikely(!count))
+ return count;
+
+ while (count) {
+ ssize_t status;
+
+ status = at24_eeprom_write(at24, buf, off, count);
+ if (status <= 0) {
+ if (retval == 0)
+ retval = status;
+ break;
+ }
+ buf += status;
+ off += status;
+ count -= status;
+ retval += status;
+ }
+
+ return retval;
+}
+
+static ssize_t at24_cdev_write(struct cdev *cdev, const void *buf, size_t count,
+ loff_t off, ulong flags)
+{
+ struct at24_data *at24 = cdev->priv;
+
+ return at24_write(at24, buf, off, count);
+}
+
+static int at24_probe(struct device_d *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct at24_platform_data chip;
+ bool writable;
+ struct at24_data *at24;
+ int err;
+ unsigned i, num_addresses;
+
+ if (dev->platform_data) {
+ chip = *(struct at24_platform_data *)dev->platform_data;
+ } else {
+ unsigned long magic;
+
+ err = dev_get_drvdata(dev, (unsigned long *)&magic);
+ if (err)
+ return err;
+
+ chip.byte_len = BIT(magic & AT24_BITMASK(AT24_SIZE_BYTELEN));
+ magic >>= AT24_SIZE_BYTELEN;
+ chip.flags = magic & AT24_BITMASK(AT24_SIZE_FLAGS);
+ /*
+ * This is slow, but we can't know all eeproms, so we better
+ * play safe. Specifying custom eeprom-types via platform_data
+ * is recommended anyhow.
+ */
+ chip.page_size = 1;
+ }
+
+ if (!is_power_of_2(chip.byte_len))
+ dev_warn(&client->dev,
+ "byte_len looks suspicious (no power of 2)!\n");
+ if (!chip.page_size) {
+ dev_err(&client->dev, "page_size must not be 0!\n");
+ err = -EINVAL;
+ goto err_out;
+ }
+ if (!is_power_of_2(chip.page_size))
+ dev_warn(&client->dev,
+ "page_size looks suspicious (no power of 2)!\n");
+
+ if (chip.flags & AT24_FLAG_TAKE8ADDR)
+ num_addresses = 8;
+ else
+ num_addresses = DIV_ROUND_UP(chip.byte_len,
+ (chip.flags & AT24_FLAG_ADDR16) ? 65536 : 256);
+
+ at24 = xzalloc(sizeof(struct at24_data) +
+ num_addresses * sizeof(struct i2c_client *));
+
+ at24->chip = chip;
+ at24->num_addresses = num_addresses;
+ at24->cdev.name = asprintf("eeprom%d", dev->id);
+ at24->cdev.priv = at24;
+ at24->cdev.dev = dev;
+ at24->cdev.ops = &at24->fops;
+ at24->fops.lseek = dev_lseek_default;
+ at24->fops.read = at24_cdev_read,
+ at24->cdev.size = chip.byte_len;
+
+ writable = !(chip.flags & AT24_FLAG_READONLY);
+ if (writable) {
+ unsigned write_max = chip.page_size;
+
+ at24->fops.write = at24_cdev_write;
+
+ if (write_max > io_limit)
+ write_max = io_limit;
+ at24->write_max = write_max;
+
+ /* buffer (data + address at the beginning) */
+ at24->writebuf = xmalloc(write_max + 2);
+ }
+
+ at24->client[0] = client;
+
+ /* use dummy devices for multiple-address chips */
+ for (i = 1; i < num_addresses; i++) {
+ at24->client[i] = i2c_new_dummy(client->adapter,
+ client->addr + i);
+ if (!at24->client[i]) {
+ dev_err(&client->dev, "address 0x%02x unavailable\n",
+ client->addr + i);
+ err = -EADDRINUSE;
+ goto err_clients;
+ }
+ }
+
+ devfs_create(&at24->cdev);
+
+ return 0;
+
+err_clients:
+ kfree(at24->writebuf);
+ kfree(at24);
+err_out:
+ dev_dbg(&client->dev, "probe error %d\n", err);
+ return err;
+
+}
+
+static struct driver_d at24_driver = {
+ .name = "at24",
+ .probe = at24_probe,
+ .id_table = at24_ids,
+};
+
+static int at24_init(void)
+{
+ i2c_register_driver(&at24_driver);
+ return 0;
+}
+device_initcall(at24_init);
diff --git a/include/i2c/at24.h b/include/i2c/at24.h
new file mode 100644
index 0000000..1013308
--- /dev/null
+++ b/include/i2c/at24.h
@@ -0,0 +1,35 @@
+/*
+ * at24.h - platform_data for the at24 (generic eeprom) driver
+ * (C) Copyright 2008 by Pengutronix
+ * (C) Copyright 2012 by Wolfram Sang
+ * same license as the driver
+ */
+
+#ifndef _LINUX_AT24_H
+#define _LINUX_AT24_H
+
+#include <linux/types.h>
+
+/**
+ * struct at24_platform_data - data to set up at24 (generic eeprom) driver
+ * @byte_len: size of eeprom in byte
+ * @page_size: number of byte which can be written in one go
+ * @flags: tunable options, check AT24_FLAG_* defines
+ *
+ * If you set up a custom eeprom type, please double-check the parameters.
+ * Especially page_size needs extra care, as you risk data loss if your value
+ * is bigger than what the chip actually supports!
+ *
+ */
+
+struct at24_platform_data {
+ u32 byte_len; /* size (sum of all addr) */
+ u16 page_size; /* for writes */
+ u8 flags;
+#define AT24_FLAG_ADDR16 0x80 /* address pointer is 16 bit */
+#define AT24_FLAG_READONLY 0x40 /* sysfs-entry will be read-only */
+#define AT24_FLAG_IRUGO 0x20 /* sysfs-entry will be world-readable */
+#define AT24_FLAG_TAKE8ADDR 0x10 /* take always 8 addresses (24c00) */
+};
+
+#endif /* _LINUX_AT24_H */
--
1.7.10.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 0/3] i2c: add at24 eeprom support
2012-11-03 20:56 [PATCH 0/3] i2c: add at24 eeprom support Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 1/3] import log2 support from linux Jean-Christophe PLAGNIOL-VILLARD
@ 2012-11-12 7:38 ` Sascha Hauer
1 sibling, 0 replies; 5+ messages in thread
From: Sascha Hauer @ 2012-11-12 7:38 UTC (permalink / raw)
To: Jean-Christophe PLAGNIOL-VILLARD; +Cc: barebox
On Sat, Nov 03, 2012 at 09:56:55PM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> HI,
>
> this patch serie add the at24 eeprom support based on linux 3.6
>
> the depends on the i2c prepare 1t24 support patch series
>
> The following changes since commit 5526278ac77ecd7109c9c1bbc35d7c74875902e7:
>
> i2c: add id_table support (2012-11-03 13:33:54 +0800)
>
> are available in the git repository at:
>
> git://git.jcrosoft.org/barebox.git delivery/at24
>
> for you to fetch changes up to fe6968e20c39461df068d5cc15869012be4a3161:
Applied, thanks
Sascha
>
> eeprom: add at24 support (2012-11-03 13:46:50 +0800)
>
> ----------------------------------------------------------------
> Jean-Christophe PLAGNIOL-VILLARD (3):
> import log2 support from linux
> add roundup and rounddown support
> eeprom: add at24 support
>
> drivers/eeprom/Kconfig | 19 ++++++++++
> drivers/eeprom/Makefile | 1 +
> drivers/eeprom/at24.c | 460 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> include/i2c/at24.h | 35 +++++++++++++++++++
> include/linux/kernel.h | 15 ++++++++
> include/linux/log2.h | 190 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> 6 files changed, 720 insertions(+)
> create mode 100644 drivers/eeprom/at24.c
> create mode 100644 include/i2c/at24.h
> create mode 100644 include/linux/log2.h
>
> Best Regards,
> J.
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2012-11-12 7:38 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-11-03 20:56 [PATCH 0/3] i2c: add at24 eeprom support Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 1/3] import log2 support from linux Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 2/3] add roundup and rounddown support Jean-Christophe PLAGNIOL-VILLARD
2012-11-03 20:58 ` [PATCH 3/3] eeprom: add at24 support Jean-Christophe PLAGNIOL-VILLARD
2012-11-12 7:38 ` [PATCH 0/3] i2c: add at24 eeprom support Sascha Hauer
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox