From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
To: barebox@lists.infradead.org
Subject: [PATCH 6/6] sama5d3xek: add lcd support
Date: Thu, 31 Jan 2013 00:20:17 +0100 [thread overview]
Message-ID: <1359588017-20045-6-git-send-email-plagnioj@jcrosoft.com> (raw)
In-Reply-To: <1359588017-20045-1-git-send-email-plagnioj@jcrosoft.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
---
arch/arm/boards/sama5d3xek/init.c | 45 +++++++++++++++++++++++++++++++++
arch/arm/configs/sama5d3xek_defconfig | 4 +++
2 files changed, 49 insertions(+)
diff --git a/arch/arm/boards/sama5d3xek/init.c b/arch/arm/boards/sama5d3xek/init.c
index ae23a31..d58bf44 100644
--- a/arch/arm/boards/sama5d3xek/init.c
+++ b/arch/arm/boards/sama5d3xek/init.c
@@ -153,6 +153,50 @@ static void ek_add_device_eth(void)
static void ek_add_device_eth(void) {}
#endif
+#if defined(CONFIG_DRIVER_VIDEO_ATMEL_HLCD)
+/*
+ * LCD Controller
+ */
+static struct fb_videomode at91_tft_vga_modes[] = {
+ {
+ .name = "LG",
+ .refresh = 60,
+ .xres = 800, .yres = 480,
+ .pixclock = KHZ2PICOS(33260),
+
+ .left_margin = 88, .right_margin = 168,
+ .upper_margin = 8, .lower_margin = 37,
+ .hsync_len = 128, .vsync_len = 2,
+
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+};
+
+/* Default output mode is TFT 24 bit */
+#define BPP_OUT_DEFAULT_LCDCFG5 (LCDC_LCDCFG5_MODE_OUTPUT_24BPP)
+
+/* Driver datas */
+static struct atmel_lcdfb_platform_data ek_lcdc_data = {
+ .lcdcon_is_backlight = true,
+ .default_bpp = 16,
+ .default_dmacon = ATMEL_LCDC_DMAEN,
+ .default_lcdcon2 = BPP_OUT_DEFAULT_LCDCFG5,
+ .guard_time = 9,
+ .lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB,
+ .mode_list = at91_tft_vga_modes,
+ .num_modes = ARRAY_SIZE(at91_tft_vga_modes),
+};
+
+static void ek_add_device_lcdc(void)
+{
+ at91_add_device_lcdc(&ek_lcdc_data);
+}
+
+#else
+static void ek_add_device_lcdc(void) {}
+#endif
+
#if defined(CONFIG_MCI_ATMEL)
/*
* MCI (SD/MMC)
@@ -333,6 +377,7 @@ static int at91sama5d3xek_devices_init(void)
ek_add_device_eth();
ek_add_device_spi();
ek_add_device_mci();
+ ek_add_device_lcdc();
armlinux_set_bootparams((void *)(SAMA5_DDRCS + 0x100));
diff --git a/arch/arm/configs/sama5d3xek_defconfig b/arch/arm/configs/sama5d3xek_defconfig
index c94419a..970ded5 100644
--- a/arch/arm/configs/sama5d3xek_defconfig
+++ b/arch/arm/configs/sama5d3xek_defconfig
@@ -43,6 +43,7 @@ CONFIG_CMD_GO=y
CONFIG_CMD_OFTREE=y
CONFIG_CMD_MTEST=y
CONFIG_CMD_MTEST_ALTERNATIVE=y
+CONFIG_CMD_SPLASH=y
CONFIG_CMD_TIMEOUT=y
CONFIG_CMD_PARTITION=y
CONFIG_CMD_GPIO=y
@@ -71,6 +72,8 @@ CONFIG_NAND=y
CONFIG_NAND_ATMEL=y
CONFIG_NAND_ATMEL_PMECC=y
CONFIG_UBI=y
+CONFIG_VIDEO=y
+CONFIG_DRIVER_VIDEO_ATMEL_HLCD=y
CONFIG_MCI=y
CONFIG_MCI_STARTUP=y
CONFIG_MCI_ATMEL=y
@@ -89,3 +92,4 @@ CONFIG_FS_TFTP=y
CONFIG_FS_FAT=y
CONFIG_FS_FAT_WRITE=y
CONFIG_FS_FAT_LFN=y
+CONFIG_PNG=y
--
1.7.10.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
prev parent reply other threads:[~2013-01-30 23:21 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-01-30 23:08 [PATCH 0/6] atmel: add Atmel HLCDC support and boards Jean-Christophe PLAGNIOL-VILLARD
2013-01-30 23:20 ` [PATCH 1/6] atmel_lcdfb: factorise common code between lcdc and new hlcdc IP Jean-Christophe PLAGNIOL-VILLARD
2013-01-30 23:20 ` [PATCH 2/6] video: add Atmel HLCD support Jean-Christophe PLAGNIOL-VILLARD
2013-01-30 23:20 ` [PATCH 3/6] at91sam9x5: add lcd support Jean-Christophe PLAGNIOL-VILLARD
2013-01-30 23:20 ` [PATCH 4/6] at91sam9x5ek: " Jean-Christophe PLAGNIOL-VILLARD
2013-01-30 23:20 ` [PATCH 5/6] sama5d3: " Jean-Christophe PLAGNIOL-VILLARD
2013-01-30 23:20 ` Jean-Christophe PLAGNIOL-VILLARD [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1359588017-20045-6-git-send-email-plagnioj@jcrosoft.com \
--to=plagnioj@jcrosoft.com \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox