* [PATCH 0/2] add mxs application uart driver @ 2013-02-26 18:34 Marc Kleine-Budde 2013-02-26 18:34 ` [PATCH 1/2] driver/serial: Kconfig: explicitly state that existing mxs driver is for the debug uart Marc Kleine-Budde 2013-02-26 18:34 ` [PATCH 2/2] driver/serial: add driver for the mxs application uart Marc Kleine-Budde 0 siblings, 2 replies; 5+ messages in thread From: Marc Kleine-Budde @ 2013-02-26 18:34 UTC (permalink / raw) To: barebox Hello, this series adds support for the mxs application uart driver. Lifted from TQS's u-boot patches. regards, Marc _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/2] driver/serial: Kconfig: explicitly state that existing mxs driver is for the debug uart 2013-02-26 18:34 [PATCH 0/2] add mxs application uart driver Marc Kleine-Budde @ 2013-02-26 18:34 ` Marc Kleine-Budde 2013-02-26 18:34 ` [PATCH 2/2] driver/serial: add driver for the mxs application uart Marc Kleine-Budde 1 sibling, 0 replies; 5+ messages in thread From: Marc Kleine-Budde @ 2013-02-26 18:34 UTC (permalink / raw) To: barebox Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> --- drivers/serial/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index a8be9cd..b23d17e 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -21,7 +21,7 @@ config DRIVER_SERIAL_IMX config DRIVER_SERIAL_STM378X depends on ARCH_MXS default y - bool "i.MX23/i.MX28 serial driver" + bool "i.MX23/i.MX28 debug UART serial driver" config DRIVER_SERIAL_NETX depends on ARCH_NETX -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 2/2] driver/serial: add driver for the mxs application uart 2013-02-26 18:34 [PATCH 0/2] add mxs application uart driver Marc Kleine-Budde 2013-02-26 18:34 ` [PATCH 1/2] driver/serial: Kconfig: explicitly state that existing mxs driver is for the debug uart Marc Kleine-Budde @ 2013-02-26 18:34 ` Marc Kleine-Budde 2013-02-26 19:02 ` Sascha Hauer 1 sibling, 1 reply; 5+ messages in thread From: Marc Kleine-Budde @ 2013-02-26 18:34 UTC (permalink / raw) To: barebox Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> --- drivers/serial/Makefile | 1 + drivers/serial/serial_auart.c | 257 +++++++++++++++++++++++++++++++++++++++++ 2 files changed, 258 insertions(+) create mode 100644 drivers/serial/serial_auart.c diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 893e282..6b90593 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -21,3 +21,4 @@ obj-$(CONFIG_DRIVER_SERIAL_ALTERA) += serial_altera.o obj-$(CONFIG_DRIVER_SERIAL_ALTERA_JTAG) += serial_altera_jtag.o obj-$(CONFIG_DRIVER_SERIAL_PXA) += serial_pxa.o obj-$(CONFIG_DRIVER_SERIAL_OMAP4_USBBOOT) += serial_omap4_usbboot.o +obj-$(CONFIG_DRIVER_SERIAL_AUART) += serial_auart.o diff --git a/drivers/serial/serial_auart.c b/drivers/serial/serial_auart.c new file mode 100644 index 0000000..5208a5d --- /dev/null +++ b/drivers/serial/serial_auart.c @@ -0,0 +1,257 @@ +/* + * (C) 2013 Marc Kleine-Budde <mkl@pengutronix.de> + * + * Based on the stm-serial driver: + * + * (C) Copyright 2010 Juergen Beisert - Pengutronix + * + * ...also based on the u-boot auart driver: + * + * (C) 2011 Wolfgang Ocker <weo@reccoware.de> + * + * Based on the standard DUART serial driver: + * + * (C) 2007 Sascha Hauer <s.hauer@pengutronix.de> + * + * (C) Copyright 2009-2010 Freescale Semiconductor, Inc. + * + * Further based on the Linux mxs-auart.c driver: + * + * Freescale STMP37XX/STMP378X Application UART driver + * + * Author: dmitry pervushin <dimka@embeddedalley.com> + * + * Copyright 2008-2010 Freescale Semiconductor, Inc. + * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <common.h> +#include <gpio.h> +#include <init.h> +#include <io.h> +#include <malloc.h> +#include <notifier.h> + +#include <mach/clock.h> +#include <mach/imx-regs.h> + +#define HW_UARTAPP_CTRL0 (0x00000000) +#define HW_UARTAPP_CTRL0_CLR (0x00000008) +#define BM_UARTAPP_CTRL0_SFTRST (0x80000000) +#define BM_UARTAPP_CTRL0_CLKGATE (0x40000000) + +#define HW_UARTAPP_CTRL2 (0x00000020) +#define HW_UARTAPP_CTRL2_SET (0x00000024) +#define HW_UARTAPP_CTRL2_CLR (0x00000028) +#define BM_UARTAPP_CTRL2_CTSEN (0x00008000) +#define BM_UARTAPP_CTRL2_RTSEN (0x00004000) +#define BM_UARTAPP_CTRL2_RXE (0x00000200) +#define BM_UARTAPP_CTRL2_TXE (0x00000100) +#define BM_UARTAPP_CTRL2_USE_LCR2 (0x00000040) +#define BM_UARTAPP_CTRL2_UARTEN (0x00000001) + +#define HW_UARTAPP_LINECTRL (0x00000030) +#define BM_UARTAPP_LINECTRL_FEN (0x00000010) + +#define BM_UARTAPP_LINECTRL_BAUD_DIVFRAC (0x00003F00) +#define BF_UARTAPP_LINECTRL_BAUD_DIVFRAC(v) \ + (((v) << 8) & BM_UARTAPP_LINECTRL_BAUD_DIVFRAC) + +#define BP_UARTAPP_LINECTRL_BAUD_DIVINT (16) +#define BM_UARTAPP_LINECTRL_BAUD_DIVINT (0xFFFF0000) +#define BF_UARTAPP_LINECTRL_BAUD_DIVINT(v) \ + (((v) << 16) & BM_UARTAPP_LINECTRL_BAUD_DIVINT) + +#define BP_UARTAPP_LINECTRL_WLEN (5) +#define BM_UARTAPP_LINECTRL_WLEN (0x00000060) +#define BF_UARTAPP_LINECTRL_WLEN(v) \ + (((v) << 5) & BM_UARTAPP_LINECTRL_WLEN) + +#define HW_UARTAPP_LINECTRL2_SET (0x00000044) + +#define HW_UARTAPP_INTR (0x00000050) + +#define HW_UARTAPP_DATA (0x00000060) +#define BM_UARTAPP_STAT_RXFE (0x01000000) +#define BM_UARTAPP_STAT_TXFE (0x08000000) + +#define HW_UARTAPP_STAT (0x00000070) +#define BM_UARTAPP_STAT_TXFF (0x02000000) + +struct auart_priv { + struct console_device cdev; + int baudrate; + struct notifier_block notify; + void __iomem *base; +}; + +static void auart_serial_putc(struct console_device *cdev, char c) +{ + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); + + /* Wait for room in TX FIFO */ + while (readl(priv->base + HW_UARTAPP_STAT) & BM_UARTAPP_STAT_TXFF) + ; + + writel(c, priv->base + HW_UARTAPP_DATA); +} + +static int auart_serial_tstc(struct console_device *cdev) +{ + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); + + /* Check if RX FIFO is not empty */ + return !(readl(priv->base + HW_UARTAPP_STAT) & BM_UARTAPP_STAT_RXFE); +} + +static int auart_serial_getc(struct console_device *cdev) +{ + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); + + /* Wait while TX FIFO is empty */ + while (!auart_serial_tstc(cdev)) + ; + + return readl(priv->base + HW_UARTAPP_DATA) & 0xff; +} + +static void auart_serial_flush(struct console_device *cdev) +{ + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); + + /* Wait for TX FIFO empty */ + while (readl(priv->base + HW_UARTAPP_STAT) & BM_UARTAPP_STAT_TXFE) + ; +} + +static int auart_serial_setbaudrate(struct console_device *cdev, int new_baudrate) +{ + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); + uint32_t ctrl2, quot, reg; + + /* Disable everything */ + ctrl2 = readl(priv->base + HW_UARTAPP_CTRL2); + writel(0x0, priv->base + HW_UARTAPP_CTRL2); + + /* Calculate and set baudrate */ + quot = (imx_get_xclk() * 32) / new_baudrate; + reg = BF_UARTAPP_LINECTRL_BAUD_DIVFRAC(quot & 0x3F) | + BF_UARTAPP_LINECTRL_BAUD_DIVINT(quot >> 6) | + BF_UARTAPP_LINECTRL_WLEN(3) | + BM_UARTAPP_LINECTRL_FEN; + + writel(reg, priv->base + HW_UARTAPP_LINECTRL); + + /* Re-enable debug UART */ + writel(ctrl2, priv->base + HW_UARTAPP_CTRL2); + + priv->baudrate = new_baudrate; + + return 0; +} + +static int auart_clocksource_clock_change(struct notifier_block *nb, unsigned long event, void *data) +{ + struct auart_priv *priv = container_of(nb, struct auart_priv, notify); + + return auart_serial_setbaudrate(&priv->cdev, priv->baudrate); +} + +static void auart_reset(struct auart_priv *priv) +{ + int i; + + writel(BM_UARTAPP_CTRL0_SFTRST, priv->base + HW_UARTAPP_CTRL0_CLR); + + for (i = 0; i < 10000; i++) { + uint32_t reg; + + reg = readl(priv->base + HW_UARTAPP_CTRL0); + if (!(reg & BM_UARTAPP_CTRL0_SFTRST)) + break; + } + + writel(BM_UARTAPP_CTRL0_CLKGATE, priv->base + HW_UARTAPP_CTRL0_CLR); +} + +static void auart_serial_init_port(struct auart_priv *priv) +{ + auart_reset(priv); + + /* Disable UART */ + writel(0x0, priv->base + HW_UARTAPP_CTRL2); + /* Mask interrupts */ + writel(0x0, priv->base + HW_UARTAPP_INTR); +} + +static int auart_serial_probe(struct device_d *dev) +{ + struct auart_priv *priv; + struct console_device *cdev; + + priv = xzalloc(sizeof *priv); + cdev = &priv->cdev; + + cdev->f_caps = CONSOLE_STDIN | CONSOLE_STDOUT | CONSOLE_STDERR; + cdev->tstc = auart_serial_tstc; + cdev->putc = auart_serial_putc; + cdev->getc = auart_serial_getc; + cdev->flush = auart_serial_flush; + cdev->setbrg = auart_serial_setbaudrate; + cdev->dev = dev; + + dev->priv = priv; + priv->base = dev_request_mem_region(dev, 0); + + auart_serial_init_port(priv); + auart_serial_setbaudrate(cdev, CONFIG_BAUDRATE); + + /* Disable RTS/CTS, enable Rx, Tx, UART */ + writel(BM_UARTAPP_CTRL2_RTSEN | BM_UARTAPP_CTRL2_CTSEN | + BM_UARTAPP_CTRL2_USE_LCR2, + priv->base + HW_UARTAPP_CTRL2_CLR); + writel(BM_UARTAPP_CTRL2_RXE | BM_UARTAPP_CTRL2_TXE | + BM_UARTAPP_CTRL2_UARTEN, + priv->base + HW_UARTAPP_CTRL2_SET); + + console_register(cdev); + priv->notify.notifier_call = auart_clocksource_clock_change; + clock_register_client(&priv->notify); + + return 0; +} + + +static void auart_serial_remove(struct device_d *dev) +{ + struct auart_priv *priv = dev->priv; + + auart_serial_flush(&priv->cdev); + console_unregister(&priv->cdev); + free(priv); +} + +static struct driver_d auart_serial_driver = { + .name = "auart_serial", + .probe = auart_serial_probe, + .remove = auart_serial_remove, +}; + +static int auart_serial_init(void) +{ + platform_driver_register(&auart_serial_driver); + return 0; +} + +console_initcall(auart_serial_init); -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] driver/serial: add driver for the mxs application uart 2013-02-26 18:34 ` [PATCH 2/2] driver/serial: add driver for the mxs application uart Marc Kleine-Budde @ 2013-02-26 19:02 ` Sascha Hauer 0 siblings, 0 replies; 5+ messages in thread From: Sascha Hauer @ 2013-02-26 19:02 UTC (permalink / raw) To: Marc Kleine-Budde; +Cc: barebox On Tue, Feb 26, 2013 at 07:34:50PM +0100, Marc Kleine-Budde wrote: > Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> > --- > drivers/serial/Makefile | 1 + > drivers/serial/serial_auart.c | 257 +++++++++++++++++++++++++++++++++++++++++ > 2 files changed, 258 insertions(+) > create mode 100644 drivers/serial/serial_auart.c > > diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile > index 893e282..6b90593 100644 > --- a/drivers/serial/Makefile > +++ b/drivers/serial/Makefile > @@ -21,3 +21,4 @@ obj-$(CONFIG_DRIVER_SERIAL_ALTERA) += serial_altera.o > obj-$(CONFIG_DRIVER_SERIAL_ALTERA_JTAG) += serial_altera_jtag.o > obj-$(CONFIG_DRIVER_SERIAL_PXA) += serial_pxa.o > obj-$(CONFIG_DRIVER_SERIAL_OMAP4_USBBOOT) += serial_omap4_usbboot.o > +obj-$(CONFIG_DRIVER_SERIAL_AUART) += serial_auart.o > diff --git a/drivers/serial/serial_auart.c b/drivers/serial/serial_auart.c > new file mode 100644 > index 0000000..5208a5d > --- /dev/null > +++ b/drivers/serial/serial_auart.c > @@ -0,0 +1,257 @@ > +/* > + * (C) 2013 Marc Kleine-Budde <mkl@pengutronix.de> > + * > + * Based on the stm-serial driver: > + * > + * (C) Copyright 2010 Juergen Beisert - Pengutronix > + * > + * ...also based on the u-boot auart driver: > + * > + * (C) 2011 Wolfgang Ocker <weo@reccoware.de> > + * > + * Based on the standard DUART serial driver: > + * > + * (C) 2007 Sascha Hauer <s.hauer@pengutronix.de> > + * > + * (C) Copyright 2009-2010 Freescale Semiconductor, Inc. > + * > + * Further based on the Linux mxs-auart.c driver: > + * > + * Freescale STMP37XX/STMP378X Application UART driver > + * > + * Author: dmitry pervushin <dimka@embeddedalley.com> > + * > + * Copyright 2008-2010 Freescale Semiconductor, Inc. > + * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + */ > + > +#include <common.h> > +#include <gpio.h> > +#include <init.h> > +#include <io.h> > +#include <malloc.h> > +#include <notifier.h> > + > +#include <mach/clock.h> > +#include <mach/imx-regs.h> > + > +#define HW_UARTAPP_CTRL0 (0x00000000) > +#define HW_UARTAPP_CTRL0_CLR (0x00000008) > +#define BM_UARTAPP_CTRL0_SFTRST (0x80000000) > +#define BM_UARTAPP_CTRL0_CLKGATE (0x40000000) > + > +#define HW_UARTAPP_CTRL2 (0x00000020) > +#define HW_UARTAPP_CTRL2_SET (0x00000024) > +#define HW_UARTAPP_CTRL2_CLR (0x00000028) > +#define BM_UARTAPP_CTRL2_CTSEN (0x00008000) > +#define BM_UARTAPP_CTRL2_RTSEN (0x00004000) > +#define BM_UARTAPP_CTRL2_RXE (0x00000200) > +#define BM_UARTAPP_CTRL2_TXE (0x00000100) > +#define BM_UARTAPP_CTRL2_USE_LCR2 (0x00000040) > +#define BM_UARTAPP_CTRL2_UARTEN (0x00000001) > + > +#define HW_UARTAPP_LINECTRL (0x00000030) > +#define BM_UARTAPP_LINECTRL_FEN (0x00000010) > + > +#define BM_UARTAPP_LINECTRL_BAUD_DIVFRAC (0x00003F00) > +#define BF_UARTAPP_LINECTRL_BAUD_DIVFRAC(v) \ > + (((v) << 8) & BM_UARTAPP_LINECTRL_BAUD_DIVFRAC) > + > +#define BP_UARTAPP_LINECTRL_BAUD_DIVINT (16) > +#define BM_UARTAPP_LINECTRL_BAUD_DIVINT (0xFFFF0000) > +#define BF_UARTAPP_LINECTRL_BAUD_DIVINT(v) \ > + (((v) << 16) & BM_UARTAPP_LINECTRL_BAUD_DIVINT) > + > +#define BP_UARTAPP_LINECTRL_WLEN (5) > +#define BM_UARTAPP_LINECTRL_WLEN (0x00000060) > +#define BF_UARTAPP_LINECTRL_WLEN(v) \ > + (((v) << 5) & BM_UARTAPP_LINECTRL_WLEN) > + > +#define HW_UARTAPP_LINECTRL2_SET (0x00000044) > + > +#define HW_UARTAPP_INTR (0x00000050) > + > +#define HW_UARTAPP_DATA (0x00000060) > +#define BM_UARTAPP_STAT_RXFE (0x01000000) > +#define BM_UARTAPP_STAT_TXFE (0x08000000) > + > +#define HW_UARTAPP_STAT (0x00000070) > +#define BM_UARTAPP_STAT_TXFF (0x02000000) > + > +struct auart_priv { > + struct console_device cdev; > + int baudrate; > + struct notifier_block notify; > + void __iomem *base; > +}; > + > +static void auart_serial_putc(struct console_device *cdev, char c) > +{ > + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); > + > + /* Wait for room in TX FIFO */ > + while (readl(priv->base + HW_UARTAPP_STAT) & BM_UARTAPP_STAT_TXFF) > + ; > + > + writel(c, priv->base + HW_UARTAPP_DATA); > +} > + > +static int auart_serial_tstc(struct console_device *cdev) > +{ > + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); > + > + /* Check if RX FIFO is not empty */ > + return !(readl(priv->base + HW_UARTAPP_STAT) & BM_UARTAPP_STAT_RXFE); > +} > + > +static int auart_serial_getc(struct console_device *cdev) > +{ > + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); > + > + /* Wait while TX FIFO is empty */ The commment seems wrong. > + while (!auart_serial_tstc(cdev)) > + ; > + > + return readl(priv->base + HW_UARTAPP_DATA) & 0xff; > +} > + > +static void auart_serial_flush(struct console_device *cdev) > +{ > + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); > + > + /* Wait for TX FIFO empty */ > + while (readl(priv->base + HW_UARTAPP_STAT) & BM_UARTAPP_STAT_TXFE) > + ; > +} > + > +static int auart_serial_setbaudrate(struct console_device *cdev, int new_baudrate) > +{ > + struct auart_priv *priv = container_of(cdev, struct auart_priv, cdev); > + uint32_t ctrl2, quot, reg; > + > + /* Disable everything */ > + ctrl2 = readl(priv->base + HW_UARTAPP_CTRL2); > + writel(0x0, priv->base + HW_UARTAPP_CTRL2); > + > + /* Calculate and set baudrate */ > + quot = (imx_get_xclk() * 32) / new_baudrate; > + reg = BF_UARTAPP_LINECTRL_BAUD_DIVFRAC(quot & 0x3F) | > + BF_UARTAPP_LINECTRL_BAUD_DIVINT(quot >> 6) | > + BF_UARTAPP_LINECTRL_WLEN(3) | > + BM_UARTAPP_LINECTRL_FEN; > + > + writel(reg, priv->base + HW_UARTAPP_LINECTRL); > + > + /* Re-enable debug UART */ debug UART? > + writel(ctrl2, priv->base + HW_UARTAPP_CTRL2); > + > + priv->baudrate = new_baudrate; > + > + return 0; > +} > + > +static int auart_clocksource_clock_change(struct notifier_block *nb, unsigned long event, void *data) > +{ > + struct auart_priv *priv = container_of(nb, struct auart_priv, notify); > + > + return auart_serial_setbaudrate(&priv->cdev, priv->baudrate); > +} > + > +static void auart_reset(struct auart_priv *priv) > +{ > + int i; > + > + writel(BM_UARTAPP_CTRL0_SFTRST, priv->base + HW_UARTAPP_CTRL0_CLR); > + > + for (i = 0; i < 10000; i++) { > + uint32_t reg; > + > + reg = readl(priv->base + HW_UARTAPP_CTRL0); > + if (!(reg & BM_UARTAPP_CTRL0_SFTRST)) > + break; > + } > + > + writel(BM_UARTAPP_CTRL0_CLKGATE, priv->base + HW_UARTAPP_CTRL0_CLR); > +} Can you use mxs_reset_block here? > + > +static void auart_serial_init_port(struct auart_priv *priv) > +{ > + auart_reset(priv); > + > + /* Disable UART */ > + writel(0x0, priv->base + HW_UARTAPP_CTRL2); > + /* Mask interrupts */ > + writel(0x0, priv->base + HW_UARTAPP_INTR); > +} > + > +static int auart_serial_probe(struct device_d *dev) > +{ > + struct auart_priv *priv; > + struct console_device *cdev; > + > + priv = xzalloc(sizeof *priv); > + cdev = &priv->cdev; > + > + cdev->f_caps = CONSOLE_STDIN | CONSOLE_STDOUT | CONSOLE_STDERR; > + cdev->tstc = auart_serial_tstc; > + cdev->putc = auart_serial_putc; > + cdev->getc = auart_serial_getc; > + cdev->flush = auart_serial_flush; > + cdev->setbrg = auart_serial_setbaudrate; > + cdev->dev = dev; > + > + dev->priv = priv; > + priv->base = dev_request_mem_region(dev, 0); > + > + auart_serial_init_port(priv); > + auart_serial_setbaudrate(cdev, CONFIG_BAUDRATE); > + > + /* Disable RTS/CTS, enable Rx, Tx, UART */ > + writel(BM_UARTAPP_CTRL2_RTSEN | BM_UARTAPP_CTRL2_CTSEN | > + BM_UARTAPP_CTRL2_USE_LCR2, > + priv->base + HW_UARTAPP_CTRL2_CLR); > + writel(BM_UARTAPP_CTRL2_RXE | BM_UARTAPP_CTRL2_TXE | > + BM_UARTAPP_CTRL2_UARTEN, > + priv->base + HW_UARTAPP_CTRL2_SET); > + > + console_register(cdev); > + priv->notify.notifier_call = auart_clocksource_clock_change; > + clock_register_client(&priv->notify); > + > + return 0; > +} > + > + > +static void auart_serial_remove(struct device_d *dev) > +{ > + struct auart_priv *priv = dev->priv; > + > + auart_serial_flush(&priv->cdev); > + console_unregister(&priv->cdev); > + free(priv); > +} > + > +static struct driver_d auart_serial_driver = { > + .name = "auart_serial", > + .probe = auart_serial_probe, > + .remove = auart_serial_remove, > +}; > + > +static int auart_serial_init(void) > +{ > + platform_driver_register(&auart_serial_driver); > + return 0; return platform_driver_register please. Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v2 0/2] add mxs application uart driver @ 2013-02-28 16:22 Marc Kleine-Budde 2013-02-28 16:22 ` [PATCH 1/2] driver/serial: Kconfig: explicitly state that existing mxs driver is for the debug uart Marc Kleine-Budde 0 siblings, 1 reply; 5+ messages in thread From: Marc Kleine-Budde @ 2013-02-28 16:22 UTC (permalink / raw) To: barebox Hello, this series adds support for the mxs application uart driver. Lifted from TQS's u-boot patches. regards, Marc changes since v1: - fix comments (auart_serial_getc(), auart_serial_setbaudrate()) - use auart_serial_setbaudrate Both suggested by Sascha. _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/2] driver/serial: Kconfig: explicitly state that existing mxs driver is for the debug uart 2013-02-28 16:22 [PATCH v2 0/2] add mxs application uart driver Marc Kleine-Budde @ 2013-02-28 16:22 ` Marc Kleine-Budde 0 siblings, 0 replies; 5+ messages in thread From: Marc Kleine-Budde @ 2013-02-28 16:22 UTC (permalink / raw) To: barebox Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> --- drivers/serial/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index a8be9cd..b23d17e 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -21,7 +21,7 @@ config DRIVER_SERIAL_IMX config DRIVER_SERIAL_STM378X depends on ARCH_MXS default y - bool "i.MX23/i.MX28 serial driver" + bool "i.MX23/i.MX28 debug UART serial driver" config DRIVER_SERIAL_NETX depends on ARCH_NETX -- 1.7.10.4 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2013-02-28 16:22 UTC | newest] Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2013-02-26 18:34 [PATCH 0/2] add mxs application uart driver Marc Kleine-Budde 2013-02-26 18:34 ` [PATCH 1/2] driver/serial: Kconfig: explicitly state that existing mxs driver is for the debug uart Marc Kleine-Budde 2013-02-26 18:34 ` [PATCH 2/2] driver/serial: add driver for the mxs application uart Marc Kleine-Budde 2013-02-26 19:02 ` Sascha Hauer 2013-02-28 16:22 [PATCH v2 0/2] add mxs application uart driver Marc Kleine-Budde 2013-02-28 16:22 ` [PATCH 1/2] driver/serial: Kconfig: explicitly state that existing mxs driver is for the debug uart Marc Kleine-Budde
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox