From: Steffen Trumtrar <s.trumtrar@pengutronix.de>
To: barebox@lists.infradead.org
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Subject: [PATCH v2] mci i.MX esdhc: Fix clock divider calculation
Date: Wed, 22 May 2013 09:51:54 +0200 [thread overview]
Message-ID: <1369209114-11357-1-git-send-email-s.trumtrar@pengutronix.de> (raw)
From: Sascha Hauer <s.hauer@pengutronix.de>
This updates the i.MX esdhc divider settings to FSLs U-Boot.
Current timings work fine for SD cards, but not for eMMC.
Although the calculation is fine according to the datasheet and reading from
eMMC works, writing is broken. Atleast on i.MX53/tqma53.
With this patch the result is the same, but uses different divider values to
achieve it.
While at it, replace the udelay with a busy-loop.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
Changes since v1:
- rebased onto -next
drivers/mci/imx-esdhc.c | 46 +++++++++++++++++++++++++++-------------------
drivers/mci/sdhci.h | 1 +
2 files changed, 28 insertions(+), 19 deletions(-)
diff --git a/drivers/mci/imx-esdhc.c b/drivers/mci/imx-esdhc.c
index ae934f4..46bd6d2 100644
--- a/drivers/mci/imx-esdhc.c
+++ b/drivers/mci/imx-esdhc.c
@@ -44,7 +44,6 @@
struct fsl_esdhc_host {
struct mci_host mci;
void __iomem *regs;
- unsigned long cur_clock;
struct device_d *dev;
struct clk *clk;
};
@@ -333,30 +332,38 @@ static void set_sysctl(struct mci_host *mci, u32 clock)
void __iomem *regs = host->regs;
int sdhc_clk = clk_get_rate(host->clk);
u32 clk;
-
- if (clock < mci->f_min)
- clock = mci->f_min;
-
- pre_div = 0;
-
- for (pre_div = 1; pre_div < 256; pre_div <<= 1) {
- if (sdhc_clk / pre_div < clock * 16)
+ unsigned long cur_clock;
+
+ /*
+ * With eMMC and imx53 (sdhc_clk=200MHz) a pre_div of 1 results in
+ * pre_div=1,div=4 (=50MHz)
+ * which is valid and should work, but somehow doesn't.
+ * Starting with pre_div=2 gives
+ * pre_div=2, div=2 (=50MHz)
+ * and works fine.
+ */
+ pre_div = 2;
+
+ if (sdhc_clk == clock)
+ pre_div = 1;
+ else if (sdhc_clk / 16 > clock)
+ for (; pre_div < 256; pre_div *= 2)
+ if ((sdhc_clk / pre_div) <= (clock * 16))
+ break;
+
+ for (div = 1; div <= 16; div++)
+ if ((sdhc_clk / (div * pre_div)) <= clock)
break;
- };
-
- div = sdhc_clk / pre_div / clock;
- if (sdhc_clk / pre_div / div > clock)
- div++;
+ cur_clock = sdhc_clk / pre_div / div;
- host->cur_clock = sdhc_clk / pre_div / div;
+ dev_dbg(host->dev, "set clock: wanted: %d got: %ld\n", clock, cur_clock);
+ dev_dbg(host->dev, "pre_div: %d div: %d\n", pre_div, div);
+ /* the register values start with 0 */
div -= 1;
pre_div >>= 1;
- dev_dbg(host->dev, "set clock: wanted: %d got: %ld\n", clock, host->cur_clock);
- dev_dbg(host->dev, "pre_div: %d div: %d\n", pre_div, div);
-
clk = (pre_div << 8) | (div << 4);
esdhc_clrbits32(regs + SDHCI_CLOCK_CONTROL__TIMEOUT_CONTROL__SOFTWARE_RESET,
@@ -365,7 +372,8 @@ static void set_sysctl(struct mci_host *mci, u32 clock)
esdhc_clrsetbits32(regs + SDHCI_CLOCK_CONTROL__TIMEOUT_CONTROL__SOFTWARE_RESET,
SYSCTL_CLOCK_MASK, clk);
- udelay(10000);
+ wait_on_timeout(10 * MSECOND,
+ !(esdhc_read32(regs + SDHCI_PRESENT_STATE) & PRSSTAT_SDSTB));
clk = SYSCTL_PEREN | SYSCTL_CKEN;
diff --git a/drivers/mci/sdhci.h b/drivers/mci/sdhci.h
index ad1bbd9..b2d6779 100644
--- a/drivers/mci/sdhci.h
+++ b/drivers/mci/sdhci.h
@@ -81,6 +81,7 @@
#define PRSSTAT_CINS 0x00010000
#define PRSSTAT_BREN 0x00000800
#define PRSSTAT_BWEN 0x00000400
+#define PRSSTAT_SDSTB 0x00000008
#define PRSSTAT_DLA 0x00000004
#define PRSSTAT_CIDHB 0x00000002
#define PRSSTAT_CICHB 0x00000001
--
1.8.2.rc2
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next reply other threads:[~2013-05-22 7:52 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-22 7:51 Steffen Trumtrar [this message]
2013-05-23 7:17 ` Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1369209114-11357-1-git-send-email-s.trumtrar@pengutronix.de \
--to=s.trumtrar@pengutronix.de \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox