* [PATCH 8/8] mtd: nand: update to v3.11-rc1
2013-07-22 10:04 [PATCH] mtd nand sync with kernel Sascha Hauer
` (6 preceding siblings ...)
2013-07-22 10:04 ` [PATCH 7/8] mtd: introduce mtd_read_oob and mtd_write_oob Sascha Hauer
@ 2013-07-22 10:04 ` Sascha Hauer
7 siblings, 0 replies; 9+ messages in thread
From: Sascha Hauer @ 2013-07-22 10:04 UTC (permalink / raw)
To: barebox
This updates the NAND stuff to Linux-3.11-rc1. It is synchronized
as best as we can get:
- locks removed
- The splitting in different files we had to better support different
features has been dropped. Instead this is now done mostly with the
use of __maybe_unused
Some barebox adjustments are forward ported, like:
- Allow partial page writes
- Optionally allow to erase bad blocks
- check for all_ff before writing a page
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/arm/boards/nhk8815/setup.c | 2 -
drivers/mtd/nand/Kconfig | 29 +-
drivers/mtd/nand/Makefile | 5 +-
drivers/mtd/nand/atmel_nand.c | 15 +-
drivers/mtd/nand/nand.h | 3 +-
drivers/mtd/nand/nand_base.c | 3011 +++++++++++++++++++++++++-------
drivers/mtd/nand/nand_bbt.c | 1047 ++++++-----
drivers/mtd/nand/nand_bch.c | 243 +++
drivers/mtd/nand/nand_hwecc.c | 103 --
drivers/mtd/nand/nand_hwecc_syndrome.c | 225 ---
drivers/mtd/nand/nand_ids.c | 266 ++-
drivers/mtd/nand/nand_imx.c | 20 +-
drivers/mtd/nand/nand_mxs.c | 15 +-
drivers/mtd/nand/nand_omap_gpmc.c | 10 +-
drivers/mtd/nand/nand_swecc.c | 95 -
drivers/mtd/nand/nand_write.c | 788 ---------
include/asm-generic/errno.h | 4 +-
include/linux/mtd/bbm.h | 45 +-
include/linux/mtd/mtd.h | 11 +
include/linux/mtd/nand.h | 645 ++++---
20 files changed, 3854 insertions(+), 2728 deletions(-)
create mode 100644 drivers/mtd/nand/nand_bch.c
delete mode 100644 drivers/mtd/nand/nand_hwecc.c
delete mode 100644 drivers/mtd/nand/nand_hwecc_syndrome.c
delete mode 100644 drivers/mtd/nand/nand_swecc.c
delete mode 100644 drivers/mtd/nand/nand_write.c
diff --git a/arch/arm/boards/nhk8815/setup.c b/arch/arm/boards/nhk8815/setup.c
index 0c85b25..b1e29d3 100644
--- a/arch/arm/boards/nhk8815/setup.c
+++ b/arch/arm/boards/nhk8815/setup.c
@@ -43,8 +43,6 @@ static int nhk8815_nand_init(void)
}
static struct nomadik_nand_platform_data nhk8815_nand_data = {
- .options = NAND_COPYBACK | NAND_CACHEPRG | NAND_NO_PADDING \
- | NAND_NO_READRDY | NAND_NO_AUTOINCR,
.init = nhk8815_nand_init,
};
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index de8fb5e..de7b03f 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -13,11 +13,20 @@ config NAND_ECC_SOFT
default y
prompt "Support software ecc"
+config NAND_ECC_BCH
+ select BCH
+ bool
+ prompt "Support software BCH ecc"
+
config NAND_ECC_HW
bool
default y
prompt "Support hardware ecc"
+config NAND_ECC_HW_OOB_FIRST
+ bool
+ prompt "Support hardware ecc (oob first)"
+
config NAND_ECC_HW_SYNDROME
bool
default y
@@ -64,8 +73,9 @@ config NAND_IMX
config NAND_IMX_BBM
bool
- prompt "i.MX NAND flash bbt creation command"
+ depends on NAND_BBT
depends on NAND_IMX
+ prompt "i.MX NAND flash bbt creation command"
config NAND_MXS
bool
@@ -100,15 +110,6 @@ config NAND_S3C24XX
help
Add support for processor's NAND device controller.
-config MTD_NAND_VERIFY_WRITE
- bool "Verify NAND page writes"
- help
- This adds an extra check when data is written to the flash. The
- NAND flash device internally checks only bits transitioning
- from 1 to 0. There is a rare possibility that even though the
- device thinks the write was successful, a bit could have been
- flipped accidentally due to device wear or something else.
-
config MTD_NAND_ECC_SMC
bool "NAND ECC Smart Media byte order"
default n
@@ -116,14 +117,6 @@ config MTD_NAND_ECC_SMC
Software ECC according to the Smart Media Specification.
The original Linux implementation had byte 0 and 1 swapped.
-config MTD_NAND_MUSEUM_IDS
- bool "Enable chip ids for obsolete ancient NAND devices"
- default n
- help
- Enable this option only when your board has first generation
- NAND chips (page size 256 byte, erase size 4-8KiB). The IDs
- of these chips were reused by later, larger chips.
-
config MTD_NAND_IDS
tristate
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 0c7c8e2..a1414e1 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -1,10 +1,7 @@
# Generic NAND options
obj-$(CONFIG_NAND) += nand_ecc.o
-obj-$(CONFIG_MTD_WRITE) += nand_write.o
-obj-$(CONFIG_NAND_ECC_SOFT) += nand_ecc.o nand_swecc.o
-obj-$(CONFIG_NAND_ECC_HW) += nand_hwecc.o
-obj-$(CONFIG_NAND_ECC_HW_SYNDROME) += nand_hwecc_syndrome.o
+obj-$(CONFIG_NAND_ECC_BCH) += nand_bch.o
obj-$(CONFIG_MTD_NAND_IDS) += nand_ids.o
obj-$(CONFIG_NAND) += nand_base.o nand-bb.o
obj-$(CONFIG_NAND_BBT) += nand_bbt.o
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
index 3eb78b7..a0f0966 100644
--- a/drivers/mtd/nand/atmel_nand.c
+++ b/drivers/mtd/nand/atmel_nand.c
@@ -624,7 +624,7 @@ normal_check:
}
static int atmel_nand_pmecc_read_page(struct mtd_info *mtd,
- struct nand_chip *chip, uint8_t *buf)
+ struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
{
struct atmel_nand_host *host = chip->priv;
int eccsize = chip->ecc.size;
@@ -659,8 +659,9 @@ static int atmel_nand_pmecc_read_page(struct mtd_info *mtd,
return 0;
}
-static void atmel_nand_pmecc_write_page(struct mtd_info *mtd,
- struct nand_chip *chip, const uint8_t *buf)
+static int atmel_nand_pmecc_write_page(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf,
+ int oob_required)
{
struct atmel_nand_host *host = chip->priv;
uint32_t *eccpos = chip->ecc.layout->eccpos;
@@ -681,7 +682,7 @@ static void atmel_nand_pmecc_write_page(struct mtd_info *mtd,
!(pmecc_readl_relaxed(host->ecc, SR) & PMECC_SR_BUSY));
if (ret) {
dev_err(host->dev, "PMECC: Timeout to get ECC value.\n");
- return;
+ return -ETIMEDOUT;
}
for (i = 0; i < host->pmecc_sector_number; i++) {
@@ -694,6 +695,8 @@ static void atmel_nand_pmecc_write_page(struct mtd_info *mtd,
}
}
chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
}
static void atmel_pmecc_core_init(struct mtd_info *mtd)
@@ -881,7 +884,7 @@ static int atmel_nand_calculate(struct mtd_info *mtd,
* buf: buffer to store read data
*/
static int atmel_nand_read_page(struct mtd_info *mtd,
- struct nand_chip *chip, uint8_t *buf)
+ struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
{
int eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
@@ -1201,7 +1204,7 @@ static int __init atmel_nand_probe(struct device_d *dev)
/* first scan to find the device and get the page size */
- if (nand_scan_ident(mtd, 1)) {
+ if (nand_scan_ident(mtd, 1, NULL)) {
res = -ENXIO;
goto err_scan_ident;
}
diff --git a/drivers/mtd/nand/nand.h b/drivers/mtd/nand/nand.h
index 123258d..eb6652c 100644
--- a/drivers/mtd/nand/nand.h
+++ b/drivers/mtd/nand/nand.h
@@ -17,7 +17,8 @@ void multi_erase_cmd(struct mtd_info *mtd, int page);
void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
const uint8_t *buf);
int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf, int page, int cached, int raw);
+ uint32_t offset, int data_len, const uint8_t *buf,
+ int oob_required, int page, int cached, int raw);
int nand_erase(struct mtd_info *mtd, struct erase_info *instr);
int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
size_t *retlen, const uint8_t *buf);
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index cc7a3db..560353a 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -4,7 +4,6 @@
* Overview:
* This is the generic MTD driver for NAND flash devices. It should be
* capable of working with almost all NAND chips currently available.
- * Basic support for AG-AND chips is provided.
*
* Additional technical information is available on
* http://www.linux-mtd.infradead.org/doc/nand.html
@@ -21,9 +20,7 @@
* TODO:
* Enable cached programming for 2k page size chips
* Check, if mtd->ecctype should be set to MTD_ECC_HW
- * if we have HW ecc support.
- * The AG-AND chips have nice features for speed improvement,
- * which are not supported yet. Read / program 4 pages in one go.
+ * if we have HW ECC support.
* BBT table is not serialized, has to be fixed
*
* This program is free software; you can redistribute it and/or modify
@@ -45,10 +42,7 @@
#include <io.h>
#include <malloc.h>
#include <module.h>
-
-#include "nand.h"
-
-#ifndef DOXYGEN_SHOULD_SKIP_THIS
+#include <linux/mtd/nand_bch.h>
/* Define default oob placement schemes for large and small page devices */
static struct nand_ecclayout nand_oob_8 = {
@@ -58,7 +52,7 @@ static struct nand_ecclayout nand_oob_8 = {
{.offset = 3,
.length = 2},
{.offset = 6,
- .length = 2}}
+ .length = 2} }
};
static struct nand_ecclayout nand_oob_16 = {
@@ -66,7 +60,7 @@ static struct nand_ecclayout nand_oob_16 = {
.eccpos = {0, 1, 2, 3, 6, 7},
.oobfree = {
{.offset = 8,
- . length = 8}}
+ . length = 8} }
};
static struct nand_ecclayout nand_oob_64 = {
@@ -77,26 +71,69 @@ static struct nand_ecclayout nand_oob_64 = {
56, 57, 58, 59, 60, 61, 62, 63},
.oobfree = {
{.offset = 2,
- .length = 38}}
+ .length = 38} }
+};
+
+static struct nand_ecclayout nand_oob_128 = {
+ .eccbytes = 48,
+ .eccpos = {
+ 80, 81, 82, 83, 84, 85, 86, 87,
+ 88, 89, 90, 91, 92, 93, 94, 95,
+ 96, 97, 98, 99, 100, 101, 102, 103,
+ 104, 105, 106, 107, 108, 109, 110, 111,
+ 112, 113, 114, 115, 116, 117, 118, 119,
+ 120, 121, 122, 123, 124, 125, 126, 127},
+ .oobfree = {
+ {.offset = 2,
+ .length = 78} }
};
-#define DEFINE_LED_TRIGGER(x)
-#define DEFINE_LED_TRIGGER_GLOBAL(x)
-#define led_trigger_register_simple(x, y) do {} while(0)
-#define led_trigger_unregister_simple(x) do {} while(0)
-#define led_trigger_event(x, y) do {} while(0)
+static int nand_get_device(struct mtd_info *mtd, int new_state);
-/*
- * For devices which display every fart in the system on a separate LED. Is
- * compiled away when LED support is disabled.
+static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
+ struct mtd_oob_ops *ops);
+
+static int check_offs_len(struct mtd_info *mtd,
+ loff_t ofs, uint64_t len)
+{
+ struct nand_chip *chip = mtd->priv;
+ int ret = 0;
+
+ /* Start address must align on block boundary */
+ if (ofs & ((1 << chip->phys_erase_shift) - 1)) {
+ pr_debug("%s: unaligned address\n", __func__);
+ ret = -EINVAL;
+ }
+
+ /* Length must align on block boundary */
+ if (len & ((1 << chip->phys_erase_shift) - 1)) {
+ pr_debug("%s: length not block aligned\n", __func__);
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+/**
+ * nand_release_device - [GENERIC] release chip
+ * @mtd: MTD device structure
+ *
+ * Release chip lock and wake up anyone waiting on the device.
*/
-DEFINE_LED_TRIGGER(nand_led_trigger);
+static void nand_release_device(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ /* Release the controller and the chip */
+ chip->controller->active = NULL;
+ chip->state = FL_READY;
+}
/**
* nand_read_byte - [DEFAULT] read one byte from the chip
- * @mtd: MTD device structure
+ * @mtd: MTD device structure
*
- * Default read function for 8bit buswith
+ * Default read function for 8bit buswidth
*/
static uint8_t nand_read_byte(struct mtd_info *mtd)
{
@@ -105,11 +142,12 @@ static uint8_t nand_read_byte(struct mtd_info *mtd)
}
/**
- * nand_read_byte16 - [DEFAULT] read one byte endianess aware from the chip
- * @mtd: MTD device structure
+ * nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
+ * nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
+ * @mtd: MTD device structure
+ *
+ * Default read function for 16bit buswidth with endianness conversion.
*
- * Default read function for 16bit buswith with
- * endianess conversion
*/
static uint8_t nand_read_byte16(struct mtd_info *mtd)
{
@@ -119,10 +157,9 @@ static uint8_t nand_read_byte16(struct mtd_info *mtd)
/**
* nand_read_word - [DEFAULT] read one word from the chip
- * @mtd: MTD device structure
+ * @mtd: MTD device structure
*
- * Default read function for 16bit buswith without
- * endianess conversion
+ * Default read function for 16bit buswidth without endianness conversion.
*/
static u16 nand_read_word(struct mtd_info *mtd)
{
@@ -132,8 +169,8 @@ static u16 nand_read_word(struct mtd_info *mtd)
/**
* nand_select_chip - [DEFAULT] control CE line
- * @mtd: MTD device structure
- * @chipnr: chipnumber to select, -1 for deselect
+ * @mtd: MTD device structure
+ * @chipnr: chipnumber to select, -1 for deselect
*
* Default select function for 1 chip devices.
*/
@@ -147,56 +184,57 @@ static void nand_select_chip(struct mtd_info *mtd, int chipnr)
break;
case 0:
break;
+
default:
- printf("%s: illegal chip number %d\n", __func__, chipnr);
+ BUG();
}
}
/**
- * nand_read_buf - [DEFAULT] read chip data into buffer
- * @mtd: MTD device structure
- * @buf: buffer to store date
- * @len: number of bytes to read
+ * nand_write_buf - [DEFAULT] write buffer to chip
+ * @mtd: MTD device structure
+ * @buf: data buffer
+ * @len: number of bytes to write
*
- * Default read function for 8bit buswith
+ * Default write function for 8bit buswidth.
*/
-static void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+static __maybe_unused void nand_write_buf(struct mtd_info *mtd,
+ const uint8_t *buf, int len)
{
int i;
struct nand_chip *chip = mtd->priv;
for (i = 0; i < len; i++)
- buf[i] = readb(chip->IO_ADDR_R);
+ writeb(buf[i], chip->IO_ADDR_W);
}
/**
- * nand_verify_buf - [DEFAULT] Verify chip data against buffer
- * @mtd: MTD device structure
- * @buf: buffer containing the data to compare
- * @len: number of bytes to compare
+ * nand_read_buf - [DEFAULT] read chip data into buffer
+ * @mtd: MTD device structure
+ * @buf: buffer to store date
+ * @len: number of bytes to read
*
- * Default verify function for 8bit buswith
+ * Default read function for 8bit buswidth.
*/
-static int nand_verify_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+static void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
{
int i;
struct nand_chip *chip = mtd->priv;
for (i = 0; i < len; i++)
- if (buf[i] != readb(chip->IO_ADDR_R))
- return -EFAULT;
- return 0;
+ buf[i] = readb(chip->IO_ADDR_R);
}
/**
- * nand_read_buf16 - [DEFAULT] read chip data into buffer
- * @mtd: MTD device structure
- * @buf: buffer to store date
- * @len: number of bytes to read
+ * nand_write_buf16 - [DEFAULT] write buffer to chip
+ * @mtd: MTD device structure
+ * @buf: data buffer
+ * @len: number of bytes to write
*
- * Default read function for 16bit buswith
+ * Default write function for 16bit buswidth.
*/
-static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
+static __maybe_unused void nand_write_buf16(struct mtd_info *mtd,
+ const uint8_t *buf, int len)
{
int i;
struct nand_chip *chip = mtd->priv;
@@ -204,18 +242,19 @@ static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
len >>= 1;
for (i = 0; i < len; i++)
- p[i] = readw(chip->IO_ADDR_R);
+ writew(p[i], chip->IO_ADDR_W);
+
}
/**
- * nand_verify_buf16 - [DEFAULT] Verify chip data against buffer
- * @mtd: MTD device structure
- * @buf: buffer containing the data to compare
- * @len: number of bytes to compare
+ * nand_read_buf16 - [DEFAULT] read chip data into buffer
+ * @mtd: MTD device structure
+ * @buf: buffer to store date
+ * @len: number of bytes to read
*
- * Default verify function for 16bit buswith
+ * Default read function for 16bit buswidth.
*/
-static int nand_verify_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
+static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
{
int i;
struct nand_chip *chip = mtd->priv;
@@ -223,63 +262,185 @@ static int nand_verify_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
len >>= 1;
for (i = 0; i < len; i++)
- if (p[i] != readw(chip->IO_ADDR_R))
- return -EFAULT;
-
- return 0;
+ p[i] = readw(chip->IO_ADDR_R);
}
/**
* nand_block_bad - [DEFAULT] Read bad block marker from the chip
- * @mtd: MTD device structure
- * @ofs: offset from device start
- * @getchip: 0, if the chip is already selected
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
+ * @getchip: 0, if the chip is already selected
*
* Check, if the block is bad.
*/
static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip)
{
- int page, chipnr, res = 0;
+ int page, chipnr, res = 0, i = 0;
struct nand_chip *chip = mtd->priv;
u16 bad;
+ if (chip->bbt_options & NAND_BBT_SCANLASTPAGE)
+ ofs += mtd->erasesize - mtd->writesize;
+
page = (int)(ofs >> chip->page_shift) & chip->pagemask;
if (getchip) {
chipnr = (int)(ofs >> chip->chip_shift);
+ nand_get_device(mtd, FL_READING);
+
/* Select the NAND device */
chip->select_chip(mtd, chipnr);
}
- if (chip->options & NAND_BUSWIDTH_16) {
- chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos & 0xFE,
- page);
- bad = cpu_to_le16(chip->read_word(mtd));
- if (chip->badblockpos & 0x1)
- bad >>= 8;
- if ((bad & 0xFF) != 0xff)
- res = 1;
- } else {
- chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos, page);
- if (chip->read_byte(mtd) != 0xff)
- res = 1;
+ do {
+ if (chip->options & NAND_BUSWIDTH_16) {
+ chip->cmdfunc(mtd, NAND_CMD_READOOB,
+ chip->badblockpos & 0xFE, page);
+ bad = cpu_to_le16(chip->read_word(mtd));
+ if (chip->badblockpos & 0x1)
+ bad >>= 8;
+ else
+ bad &= 0xFF;
+ } else {
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos,
+ page);
+ bad = chip->read_byte(mtd);
+ }
+
+ if (likely(chip->badblockbits == 8))
+ res = bad != 0xFF;
+ else
+ res = hweight8(bad) < chip->badblockbits;
+ ofs += mtd->writesize;
+ page = (int)(ofs >> chip->page_shift) & chip->pagemask;
+ i++;
+ } while (!res && i < 2 && (chip->bbt_options & NAND_BBT_SCAN2NDPAGE));
+
+ if (getchip) {
+ chip->select_chip(mtd, -1);
+ nand_release_device(mtd);
}
return res;
}
/**
+ * nand_default_block_markbad - [DEFAULT] mark a block bad
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
+ *
+ * This is the default implementation, which can be overridden by a hardware
+ * specific driver. We try operations in the following order, according to our
+ * bbt_options (NAND_BBT_NO_OOB_BBM and NAND_BBT_USE_FLASH):
+ * (1) erase the affected block, to allow OOB marker to be written cleanly
+ * (2) update in-memory BBT
+ * (3) write bad block marker to OOB area of affected block
+ * (4) update flash-based BBT
+ * Note that we retain the first error encountered in (3) or (4), finish the
+ * procedures, and dump the error in the end.
+*/
+static __maybe_unused int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+ struct nand_chip *chip = mtd->priv;
+ uint8_t buf[2] = { 0, 0 };
+ int block, res, ret = 0, i = 0;
+ int write_oob = !(chip->bbt_options & NAND_BBT_NO_OOB_BBM);
+
+ if (write_oob) {
+ struct erase_info einfo;
+
+ /* Attempt erase before marking OOB */
+ memset(&einfo, 0, sizeof(einfo));
+ einfo.mtd = mtd;
+ einfo.addr = ofs;
+ einfo.len = 1 << chip->phys_erase_shift;
+ nand_erase_nand(mtd, &einfo, 0);
+ }
+
+ /* Get block number */
+ block = (int)(ofs >> chip->bbt_erase_shift);
+ /* Mark block bad in memory-based BBT */
+ if (chip->bbt)
+ chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
+
+ /* Write bad block marker to OOB */
+ if (write_oob) {
+ struct mtd_oob_ops ops;
+ loff_t wr_ofs = ofs;
+
+ nand_get_device(mtd, FL_WRITING);
+
+ ops.datbuf = NULL;
+ ops.oobbuf = buf;
+ ops.ooboffs = chip->badblockpos;
+ if (chip->options & NAND_BUSWIDTH_16) {
+ ops.ooboffs &= ~0x01;
+ ops.len = ops.ooblen = 2;
+ } else {
+ ops.len = ops.ooblen = 1;
+ }
+ ops.mode = MTD_OPS_PLACE_OOB;
+
+ /* Write to first/last page(s) if necessary */
+ if (chip->bbt_options & NAND_BBT_SCANLASTPAGE)
+ wr_ofs += mtd->erasesize - mtd->writesize;
+ do {
+ res = nand_do_write_oob(mtd, wr_ofs, &ops);
+ if (!ret)
+ ret = res;
+
+ i++;
+ wr_ofs += mtd->writesize;
+ } while ((chip->bbt_options & NAND_BBT_SCAN2NDPAGE) && i < 2);
+
+ nand_release_device(mtd);
+ }
+
+ /* Update flash-based bad block table */
+ if (IS_ENABLED(CONFIG_NAND_BBT) && chip->bbt_options & NAND_BBT_USE_FLASH) {
+ res = nand_update_bbt(mtd, ofs);
+ if (!ret)
+ ret = res;
+ }
+
+ if (!ret)
+ mtd->ecc_stats.badblocks++;
+
+ return ret;
+}
+
+/**
+ * nand_check_wp - [GENERIC] check if the chip is write protected
+ * @mtd: MTD device structure
+ *
+ * Check, if the device is write protected. The function expects, that the
+ * device is already selected.
+ */
+static int nand_check_wp(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ /* Broken xD cards report WP despite being writable */
+ if (chip->options & NAND_BROKEN_XD)
+ return 0;
+
+ /* Check the WP bit */
+ chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
+ return (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1;
+}
+
+/**
* nand_block_checkbad - [GENERIC] Check if a block is marked bad
- * @mtd: MTD device structure
- * @ofs: offset from device start
- * @getchip: 0, if the chip is already selected
- * @allowbbt: 1, if its allowed to access the bbt area
+ * @mtd: MTD device structure
+ * @ofs: offset from device start
+ * @getchip: 0, if the chip is already selected
+ * @allowbbt: 1, if its allowed to access the bbt area
*
* Check, if the block is bad. Either by reading the bad block table or
* calling of the scan function.
*/
-int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip,
+static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip,
int allowbbt)
{
struct nand_chip *chip = mtd->priv;
@@ -287,6 +448,7 @@ int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip,
#ifdef CONFIG_NAND_BBT
if (!chip->bbt)
return chip->block_bad(mtd, ofs, getchip);
+
/* Return info from the table */
return nand_isbad_bbt(mtd, ofs, allowbbt);
#else
@@ -294,34 +456,28 @@ int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip,
#endif
}
-/*
- * Wait for the ready pin, after a command
- * The timeout is catched later.
- */
+/* Wait for the ready pin, after a command. The timeout is caught later. */
void nand_wait_ready(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
uint64_t start = get_time_ns();
- led_trigger_event(nand_led_trigger, LED_FULL);
/* wait until command is processed or timeout occures */
do {
if (chip->dev_ready(mtd))
break;
} while (!is_timeout(start, SECOND * 2));
- led_trigger_event(nand_led_trigger, LED_OFF);
}
-EXPORT_SYMBOL(nand_wait_ready);
/**
* nand_command - [DEFAULT] Send command to NAND device
- * @mtd: MTD device structure
- * @command: the command to be sent
- * @column: the column address for this command, -1 if none
- * @page_addr: the page address for this command, -1 if none
+ * @mtd: MTD device structure
+ * @command: the command to be sent
+ * @column: the column address for this command, -1 if none
+ * @page_addr: the page address for this command, -1 if none
*
- * Send command to NAND device. This function is used for small page
- * devices (256/512 Bytes per page)
+ * Send command to NAND device. This function is used for small page devices
+ * (512 Bytes per page).
*/
static void nand_command(struct mtd_info *mtd, unsigned int command,
int column, int page_addr)
@@ -329,10 +485,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
register struct nand_chip *chip = mtd->priv;
int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE;
- /*
- * Write out the command to the device.
- */
- if (command == NAND_CMD_SEQIN) {
+ /* Write out the command to the device */
+ if (IS_ENABLED(CONFIG_MTD_WRITE) && command == NAND_CMD_SEQIN) {
int readcmd;
if (column >= mtd->writesize) {
@@ -351,9 +505,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
}
chip->cmd_ctrl(mtd, command, ctrl);
- /*
- * Address cycle, when necessary
- */
+ /* Address cycle, when necessary */
ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE;
/* Serially input address */
if (column != -1) {
@@ -374,8 +526,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
/*
- * program and erase have their own busy handlers
- * status and sequential in needs no delay
+ * Program and erase have their own busy handlers status and sequential
+ * in needs no delay
*/
switch (command) {
@@ -394,7 +546,8 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
NAND_CTRL_CLE | NAND_CTRL_CHANGE);
chip->cmd_ctrl(mtd,
NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
- while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ;
+ while (!(chip->read_byte(mtd) & NAND_STATUS_READY))
+ ;
return;
/* This applies to read commands */
@@ -408,8 +561,10 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
return;
}
}
- /* Apply this short delay always to ensure that we do wait tWB in
- * any case on any machine. */
+ /*
+ * Apply this short delay always to ensure that we do wait tWB in
+ * any case on any machine.
+ */
ndelay(100);
nand_wait_ready(mtd);
@@ -417,14 +572,14 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
/**
* nand_command_lp - [DEFAULT] Send command to NAND large page device
- * @mtd: MTD device structure
- * @command: the command to be sent
- * @column: the column address for this command, -1 if none
- * @page_addr: the page address for this command, -1 if none
+ * @mtd: MTD device structure
+ * @command: the command to be sent
+ * @column: the column address for this command, -1 if none
+ * @page_addr: the page address for this command, -1 if none
*
* Send command to NAND device. This is the version for the new large page
- * devices We dont have the separate regions as we have in the small page
- * devices. We must emulate NAND_CMD_READOOB to keep the code compatible.
+ * devices. We don't have the separate regions as we have in the small page
+ * devices. We must emulate NAND_CMD_READOOB to keep the code compatible.
*/
static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
int column, int page_addr)
@@ -438,8 +593,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
}
/* Command latch cycle */
- chip->cmd_ctrl(mtd, command & 0xff,
- NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
+ chip->cmd_ctrl(mtd, command, NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
if (column != -1 || page_addr != -1) {
int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE;
@@ -466,8 +620,8 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
/*
- * program and erase have their own busy handlers
- * status, sequential in, and deplete1 need no delay
+ * Program and erase have their own busy handlers status, sequential
+ * in, and deplete1 need no delay.
*/
switch (command) {
@@ -478,18 +632,6 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
case NAND_CMD_SEQIN:
case NAND_CMD_RNDIN:
case NAND_CMD_STATUS:
- case NAND_CMD_DEPLETE1:
- return;
-
- /*
- * read error status commands require only a short delay
- */
- case NAND_CMD_STATUS_ERROR:
- case NAND_CMD_STATUS_ERROR0:
- case NAND_CMD_STATUS_ERROR1:
- case NAND_CMD_STATUS_ERROR2:
- case NAND_CMD_STATUS_ERROR3:
- udelay(chip->chip_delay);
return;
case NAND_CMD_RESET:
@@ -500,7 +642,8 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
chip->cmd_ctrl(mtd, NAND_CMD_NONE,
NAND_NCE | NAND_CTRL_CHANGE);
- while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ;
+ while (!(chip->read_byte(mtd) & NAND_STATUS_READY))
+ ;
return;
case NAND_CMD_RNDOUT:
@@ -521,7 +664,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
default:
/*
* If we don't have access to the busy pin, we apply the given
- * command delay
+ * command delay.
*/
if (!chip->dev_ready) {
udelay(chip->chip_delay);
@@ -529,14 +672,46 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
}
}
- /* Apply this short delay always to ensure that we do wait tWB in
- * any case on any machine. */
+ /*
+ * Apply this short delay always to ensure that we do wait tWB in
+ * any case on any machine.
+ */
ndelay(100);
nand_wait_ready(mtd);
}
/**
+ * nand_get_device - [GENERIC] Get chip for selected access
+ * @mtd: MTD device structure
+ * @new_state: the state which is requested
+ *
+ * Get the device and lock it for exclusive access
+ */
+static int
+nand_get_device(struct mtd_info *mtd, int new_state)
+{
+ struct nand_chip *chip = mtd->priv;
+retry:
+
+ /* Hardware controller shared among independent devices */
+ if (!chip->controller->active)
+ chip->controller->active = chip;
+
+ if (chip->controller->active == chip && chip->state == FL_READY) {
+ chip->state = new_state;
+ return 0;
+ }
+ if (new_state == FL_PM_SUSPENDED) {
+ if (chip->controller->active->state == FL_PM_SUSPENDED) {
+ chip->state = FL_PM_SUSPENDED;
+ return 0;
+ }
+ }
+ goto retry;
+}
+
+/**
* nand_wait - [DEFAULT] wait until the command is done
* @mtd: MTD device structure
* @chip: NAND chip structure
@@ -557,16 +732,11 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
else
timeo = 20 * MSECOND;
- led_trigger_event(nand_led_trigger, LED_FULL);
-
/* Apply this short delay always to ensure that we do wait tWB in
* any case on any machine. */
ndelay(100);
- if ((state == FL_ERASING) && (chip->options & NAND_IS_AND))
- chip->cmdfunc(mtd, NAND_CMD_STATUS_MULTI, -1, -1);
- else
- chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
+ chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
while (!is_timeout(start, timeo)) {
if (chip->dev_ready) {
@@ -577,172 +747,690 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
break;
}
}
- led_trigger_event(nand_led_trigger, LED_OFF);
status = (int)chip->read_byte(mtd);
return status;
}
/**
- * nand_read_page_raw - [Intern] read raw page data without ecc
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
+ * __nand_unlock - [REPLACEABLE] unlocks specified locked blocks
+ * @mtd: mtd info
+ * @ofs: offset to start unlock from
+ * @len: length to unlock
+ * @invert: when = 0, unlock the range of blocks within the lower and
+ * upper boundary address
+ * when = 1, unlock the range of blocks outside the boundaries
+ * of the lower and upper boundary address
+ *
+ * Returs unlock status.
*/
-static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf)
+static int __nand_unlock(struct mtd_info *mtd, loff_t ofs,
+ uint64_t len, int invert)
{
- chip->read_buf(mtd, buf, mtd->writesize);
- chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
- return 0;
+ int ret = 0;
+ int status, page;
+ struct nand_chip *chip = mtd->priv;
+
+ /* Submit address of first page to unlock */
+ page = ofs >> chip->page_shift;
+ chip->cmdfunc(mtd, NAND_CMD_UNLOCK1, -1, page & chip->pagemask);
+
+ /* Submit address of last page to unlock */
+ page = (ofs + len) >> chip->page_shift;
+ chip->cmdfunc(mtd, NAND_CMD_UNLOCK2, -1,
+ (page | invert) & chip->pagemask);
+
+ /* Call wait ready function */
+ status = chip->waitfunc(mtd, chip);
+ /* See if device thinks it succeeded */
+ if (status & NAND_STATUS_FAIL) {
+ pr_debug("%s: error status = 0x%08x\n",
+ __func__, status);
+ ret = -EIO;
+ }
+
+ return ret;
}
/**
- * nand_transfer_oob - [Internal] Transfer oob to client buffer
- * @chip: nand chip structure
- * @oob: oob destination address
- * @ops: oob ops structure
- * @len: size of oob to transfer
+ * nand_unlock - [REPLACEABLE] unlocks specified locked blocks
+ * @mtd: mtd info
+ * @ofs: offset to start unlock from
+ * @len: length to unlock
+ *
+ * Returns unlock status.
*/
-#ifdef CONFIG_NAND_READ_OOB
-static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob,
- struct mtd_oob_ops *ops, size_t len)
+int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
{
- switch(ops->mode) {
+ int ret = 0;
+ int chipnr;
+ struct nand_chip *chip = mtd->priv;
- case MTD_OPS_PLACE_OOB:
- case MTD_OPS_RAW:
- memcpy(oob, chip->oob_poi + ops->ooboffs, len);
- return oob + len;
+ pr_debug("%s: start = 0x%012llx, len = %llu\n",
+ __func__, (unsigned long long)ofs, len);
- case MTD_OPS_AUTO_OOB: {
- struct nand_oobfree *free = chip->ecc.layout->oobfree;
- uint32_t boffs = 0, roffs = ops->ooboffs;
- size_t bytes = 0;
+ if (check_offs_len(mtd, ofs, len))
+ ret = -EINVAL;
- for(; free->length && len; free++, len -= bytes) {
- /* Read request not from offset 0 ? */
- if (unlikely(roffs)) {
- if (roffs >= free->length) {
- roffs -= free->length;
- continue;
- }
- boffs = free->offset + roffs;
- bytes = min_t(size_t, len,
- (free->length - roffs));
- roffs = 0;
- } else {
- bytes = min_t(size_t, len, free->length);
- boffs = free->offset;
- }
- memcpy(oob, chip->oob_poi + boffs, bytes);
- oob += bytes;
- }
- return oob;
- }
- default:
- BUG();
+ /* Align to last block address if size addresses end of the device */
+ if (ofs + len == mtd->size)
+ len -= mtd->erasesize;
+
+ nand_get_device(mtd, FL_UNLOCKING);
+
+ /* Shift to get chip number */
+ chipnr = ofs >> chip->chip_shift;
+
+ chip->select_chip(mtd, chipnr);
+
+ /* Check, if it is write protected */
+ if (nand_check_wp(mtd)) {
+ pr_debug("%s: device is write protected!\n",
+ __func__);
+ ret = -EIO;
+ goto out;
}
- return NULL;
+
+ ret = __nand_unlock(mtd, ofs, len, 0);
+
+out:
+ chip->select_chip(mtd, -1);
+ nand_release_device(mtd);
+
+ return ret;
}
-#endif
+EXPORT_SYMBOL(nand_unlock);
/**
- * nand_do_read_ops - [Internal] Read data with ECC
+ * nand_lock - [REPLACEABLE] locks all blocks present in the device
+ * @mtd: mtd info
+ * @ofs: offset to start unlock from
+ * @len: length to unlock
*
- * @mtd: MTD device structure
- * @from: offset to read from
- * @ops: oob ops structure
+ * This feature is not supported in many NAND parts. 'Micron' NAND parts do
+ * have this feature, but it allows only to lock all blocks, not for specified
+ * range for block. Implementing 'lock' feature by making use of 'unlock', for
+ * now.
*
- * Internal function. Called with chip held.
+ * Returns lock status.
*/
-static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
- struct mtd_oob_ops *ops)
+int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
{
- int chipnr, page, realpage, col, bytes, aligned;
- struct nand_chip *chip = mtd->priv;
- struct mtd_ecc_stats stats;
- int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
- int sndcmd = 1;
int ret = 0;
- uint32_t readlen = ops->len;
- uint32_t oobreadlen = ops->ooblen;
- uint8_t *bufpoi, *oob, *buf;
+ int chipnr, status, page;
+ struct nand_chip *chip = mtd->priv;
- stats = mtd->ecc_stats;
+ pr_debug("%s: start = 0x%012llx, len = %llu\n",
+ __func__, (unsigned long long)ofs, len);
+
+ if (check_offs_len(mtd, ofs, len))
+ ret = -EINVAL;
+
+ nand_get_device(mtd, FL_LOCKING);
+
+ /* Shift to get chip number */
+ chipnr = ofs >> chip->chip_shift;
- chipnr = (int)(from >> chip->chip_shift);
chip->select_chip(mtd, chipnr);
- realpage = (int)(from >> chip->page_shift);
- page = realpage & chip->pagemask;
+ /* Check, if it is write protected */
+ if (nand_check_wp(mtd)) {
+ pr_debug("%s: device is write protected!\n",
+ __func__);
+ status = MTD_ERASE_FAILED;
+ ret = -EIO;
+ goto out;
+ }
- col = (int)(from & (mtd->writesize - 1));
+ /* Submit address of first page to lock */
+ page = ofs >> chip->page_shift;
+ chip->cmdfunc(mtd, NAND_CMD_LOCK, -1, page & chip->pagemask);
+
+ /* Call wait ready function */
+ status = chip->waitfunc(mtd, chip);
+ /* See if device thinks it succeeded */
+ if (status & NAND_STATUS_FAIL) {
+ pr_debug("%s: error status = 0x%08x\n",
+ __func__, status);
+ ret = -EIO;
+ goto out;
+ }
- buf = ops->datbuf;
- oob = ops->oobbuf;
+ ret = __nand_unlock(mtd, ofs, len, 0x1);
- while(1) {
- bytes = min(mtd->writesize - col, readlen);
- aligned = (bytes == mtd->writesize);
+out:
+ chip->select_chip(mtd, -1);
+ nand_release_device(mtd);
- /* Is the current page in the buffer ? */
- if (realpage != chip->pagebuf || oob) {
- bufpoi = aligned ? buf : chip->buffers->databuf;
+ return ret;
+}
+EXPORT_SYMBOL(nand_lock);
- if (likely(sndcmd)) {
- chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
- sndcmd = 0;
- }
+/**
+ * nand_read_page_raw - [INTERN] read raw page data without ecc
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ *
+ * Not for syndrome calculating ECC controllers, which use a special oob layout.
+ */
+static __maybe_unused int nand_read_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
+{
+ chip->read_buf(mtd, buf, mtd->writesize);
+ if (oob_required)
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+ return 0;
+}
- /* Now read the page into the buffer */
- if (unlikely(ops->mode == MTD_OPS_RAW))
- ret = chip->ecc.read_page_raw(mtd, chip, bufpoi);
- else
- ret = chip->ecc.read_page(mtd, chip, bufpoi);
- if (ret < 0)
- break;
+/**
+ * nand_read_page_raw_syndrome - [INTERN] read raw page data without ecc
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ *
+ * We need a special oob layout and handling even when OOB isn't used.
+ */
+static __maybe_unused int nand_read_page_raw_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf,
+ int oob_required, int page)
+{
+ int eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ uint8_t *oob = chip->oob_poi;
+ int steps, size;
+
+ for (steps = chip->ecc.steps; steps > 0; steps--) {
+ chip->read_buf(mtd, buf, eccsize);
+ buf += eccsize;
+
+ if (chip->ecc.prepad) {
+ chip->read_buf(mtd, oob, chip->ecc.prepad);
+ oob += chip->ecc.prepad;
+ }
- /* Transfer not aligned data */
- if (!aligned) {
- chip->pagebuf = realpage;
- memcpy(buf, chip->buffers->databuf + col, bytes);
- }
+ chip->read_buf(mtd, oob, eccbytes);
+ oob += eccbytes;
- buf += bytes;
+ if (chip->ecc.postpad) {
+ chip->read_buf(mtd, oob, chip->ecc.postpad);
+ oob += chip->ecc.postpad;
+ }
+ }
-#ifdef CONFIG_NAND_READ_OOB
- if (unlikely(oob)) {
- /* Raw mode does data:oob:data:oob */
- if (ops->mode != MTD_OPS_RAW) {
- int toread = min(oobreadlen,
- chip->ecc.layout->oobavail);
- if (toread) {
- oob = nand_transfer_oob(chip,
- oob, ops, toread);
- oobreadlen -= toread;
- }
- } else
- buf = nand_transfer_oob(chip,
- buf, ops, mtd->oobsize);
- }
-#endif
- if (!(chip->options & NAND_NO_READRDY)) {
- /*
- * Apply delay or wait for ready/busy pin. Do
- * this before the AUTOINCR check, so no
- * problems arise if a chip which does auto
- * increment is marked as NOAUTOINCR by the
- * board driver.
- */
- if (!chip->dev_ready)
- udelay(chip->chip_delay);
- else
+ size = mtd->oobsize - (oob - chip->oob_poi);
+ if (size)
+ chip->read_buf(mtd, oob, size);
+
+ return 0;
+}
+
+/**
+ * nand_read_page_swecc - [REPLACEABLE] software ECC based page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ */
+static __maybe_unused int nand_read_page_swecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int oob_required,
+ int page)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ unsigned int max_bitflips = 0;
+
+ chip->ecc.read_page_raw(mtd, chip, buf, 1, page);
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ ecc_code[i] = chip->oob_poi[eccpos[i]];
+
+ eccsteps = chip->ecc.steps;
+ p = buf;
+
+ for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
+ if (stat < 0) {
+ mtd->ecc_stats.failed++;
+ } else {
+ mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
+ }
+ return max_bitflips;
+}
+
+/**
+ * nand_read_subpage - [REPLACEABLE] ECC based sub-page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @data_offs: offset of requested data within the page
+ * @readlen: data length
+ * @bufpoi: buffer to store read data
+ */
+static __maybe_unused int nand_read_subpage(struct mtd_info *mtd,
+ struct nand_chip *chip, uint32_t data_offs, uint32_t readlen,
+ uint8_t *bufpoi)
+{
+ int start_step, end_step, num_steps;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ uint8_t *p;
+ int data_col_addr, i, gaps = 0;
+ int datafrag_len, eccfrag_len, aligned_len, aligned_pos;
+ int busw = (chip->options & NAND_BUSWIDTH_16) ? 2 : 1;
+ int index = 0;
+ unsigned int max_bitflips = 0;
+
+ /*
+ * Currently we have no users in barebox, so disable this for now
+ */
+ return -ENOTSUPP;
+
+ /* Column address within the page aligned to ECC size (256bytes) */
+ start_step = data_offs / chip->ecc.size;
+ end_step = (data_offs + readlen - 1) / chip->ecc.size;
+ num_steps = end_step - start_step + 1;
+
+ /* Data size aligned to ECC ecc.size */
+ datafrag_len = num_steps * chip->ecc.size;
+ eccfrag_len = num_steps * chip->ecc.bytes;
+
+ data_col_addr = start_step * chip->ecc.size;
+ /* If we read not a page aligned data */
+ if (data_col_addr != 0)
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_col_addr, -1);
+
+ p = bufpoi + data_col_addr;
+ chip->read_buf(mtd, p, datafrag_len);
+
+ /* Calculate ECC */
+ for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size)
+ chip->ecc.calculate(mtd, p, &chip->buffers->ecccalc[i]);
+
+ /*
+ * The performance is faster if we position offsets according to
+ * ecc.pos. Let's make sure that there are no gaps in ECC positions.
+ */
+ for (i = 0; i < eccfrag_len - 1; i++) {
+ if (eccpos[i + start_step * chip->ecc.bytes] + 1 !=
+ eccpos[i + start_step * chip->ecc.bytes + 1]) {
+ gaps = 1;
+ break;
+ }
+ }
+ if (gaps) {
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+ } else {
+ /*
+ * Send the command to read the particular ECC bytes take care
+ * about buswidth alignment in read_buf.
+ */
+ index = start_step * chip->ecc.bytes;
+
+ aligned_pos = eccpos[index] & ~(busw - 1);
+ aligned_len = eccfrag_len;
+ if (eccpos[index] & (busw - 1))
+ aligned_len++;
+ if (eccpos[index + (num_steps * chip->ecc.bytes)] & (busw - 1))
+ aligned_len++;
+
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT,
+ mtd->writesize + aligned_pos, -1);
+ chip->read_buf(mtd, &chip->oob_poi[aligned_pos], aligned_len);
+ }
+
+ for (i = 0; i < eccfrag_len; i++)
+ chip->buffers->ecccode[i] = chip->oob_poi[eccpos[i + index]];
+
+ p = bufpoi + data_col_addr;
+ for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size) {
+ int stat;
+
+ stat = chip->ecc.correct(mtd, p,
+ &chip->buffers->ecccode[i], &chip->buffers->ecccalc[i]);
+ if (stat < 0) {
+ mtd->ecc_stats.failed++;
+ } else {
+ mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
+ }
+ return max_bitflips;
+}
+
+/**
+ * nand_read_page_hwecc - [REPLACEABLE] hardware ECC based page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ *
+ * Not for syndrome calculating ECC controllers which need a special oob layout.
+ */
+static __maybe_unused int nand_read_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ unsigned int max_bitflips = 0;
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ chip->ecc.hwctl(mtd, NAND_ECC_READ);
+ chip->read_buf(mtd, p, eccsize);
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+ }
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ ecc_code[i] = chip->oob_poi[eccpos[i]];
+
+ eccsteps = chip->ecc.steps;
+ p = buf;
+
+ for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
+ if (stat < 0) {
+ mtd->ecc_stats.failed++;
+ } else {
+ mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
+ }
+ return max_bitflips;
+}
+
+/**
+ * nand_read_page_hwecc_oob_first - [REPLACEABLE] hw ecc, read oob first
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ *
+ * Hardware ECC for large page chips, require OOB to be read first. For this
+ * ECC mode, the write_page method is re-used from ECC_HW. These methods
+ * read/write ECC from the OOB area, unlike the ECC_HW_SYNDROME support with
+ * multiple ECC steps, follows the "infix ECC" scheme and reads/writes ECC from
+ * the data area, by overwriting the NAND manufacturer bad block markings.
+ */
+static __maybe_unused int nand_read_page_hwecc_oob_first(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ unsigned int max_bitflips = 0;
+
+ /* Read the OOB area first */
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ ecc_code[i] = chip->oob_poi[eccpos[i]];
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ chip->ecc.hwctl(mtd, NAND_ECC_READ);
+ chip->read_buf(mtd, p, eccsize);
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+
+ stat = chip->ecc.correct(mtd, p, &ecc_code[i], NULL);
+ if (stat < 0) {
+ mtd->ecc_stats.failed++;
+ } else {
+ mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
+ }
+ return max_bitflips;
+}
+
+/**
+ * nand_read_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page read
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @oob_required: caller requires OOB data read to chip->oob_poi
+ * @page: page number to read
+ *
+ * The hw generator calculates the error syndrome automatically. Therefore we
+ * need a special oob layout and handling.
+ */
+static __maybe_unused int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *oob = chip->oob_poi;
+ unsigned int max_bitflips = 0;
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ chip->ecc.hwctl(mtd, NAND_ECC_READ);
+ chip->read_buf(mtd, p, eccsize);
+
+ if (chip->ecc.prepad) {
+ chip->read_buf(mtd, oob, chip->ecc.prepad);
+ oob += chip->ecc.prepad;
+ }
+
+ chip->ecc.hwctl(mtd, NAND_ECC_READSYN);
+ chip->read_buf(mtd, oob, eccbytes);
+ stat = chip->ecc.correct(mtd, p, oob, NULL);
+
+ if (stat < 0) {
+ mtd->ecc_stats.failed++;
+ } else {
+ mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(unsigned int, max_bitflips, stat);
+ }
+
+ oob += eccbytes;
+
+ if (chip->ecc.postpad) {
+ chip->read_buf(mtd, oob, chip->ecc.postpad);
+ oob += chip->ecc.postpad;
+ }
+ }
+
+ /* Calculate remaining oob bytes */
+ i = mtd->oobsize - (oob - chip->oob_poi);
+ if (i)
+ chip->read_buf(mtd, oob, i);
+
+ return max_bitflips;
+}
+
+/**
+ * nand_transfer_oob - [INTERN] Transfer oob to client buffer
+ * @chip: nand chip structure
+ * @oob: oob destination address
+ * @ops: oob ops structure
+ * @len: size of oob to transfer
+ */
+static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob,
+ struct mtd_oob_ops *ops, size_t len)
+{
+ switch (ops->mode) {
+
+ case MTD_OPS_PLACE_OOB:
+ case MTD_OPS_RAW:
+ memcpy(oob, chip->oob_poi + ops->ooboffs, len);
+ return oob + len;
+
+ case MTD_OPS_AUTO_OOB: {
+ struct nand_oobfree *free = chip->ecc.layout->oobfree;
+ uint32_t boffs = 0, roffs = ops->ooboffs;
+ size_t bytes = 0;
+
+ for (; free->length && len; free++, len -= bytes) {
+ /* Read request not from offset 0? */
+ if (unlikely(roffs)) {
+ if (roffs >= free->length) {
+ roffs -= free->length;
+ continue;
+ }
+ boffs = free->offset + roffs;
+ bytes = min_t(size_t, len,
+ (free->length - roffs));
+ roffs = 0;
+ } else {
+ bytes = min_t(size_t, len, free->length);
+ boffs = free->offset;
+ }
+ memcpy(oob, chip->oob_poi + boffs, bytes);
+ oob += bytes;
+ }
+ return oob;
+ }
+ default:
+ BUG();
+ }
+ return NULL;
+}
+
+/**
+ * nand_do_read_ops - [INTERN] Read data with ECC
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob ops structure
+ *
+ * Internal function. Called with chip held.
+ */
+static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
+ struct mtd_oob_ops *ops)
+{
+ int chipnr, page, realpage, col, bytes, aligned, oob_required;
+ struct nand_chip *chip = mtd->priv;
+ struct mtd_ecc_stats stats;
+ int ret = 0;
+ uint32_t readlen = ops->len;
+ uint32_t oobreadlen = ops->ooblen;
+ uint32_t max_oobsize = ops->mode == MTD_OPS_AUTO_OOB ?
+ mtd->oobavail : mtd->oobsize;
+
+ uint8_t *bufpoi, *oob, *buf;
+ unsigned int max_bitflips = 0;
+
+ stats = mtd->ecc_stats;
+
+ chipnr = (int)(from >> chip->chip_shift);
+ chip->select_chip(mtd, chipnr);
+
+ realpage = (int)(from >> chip->page_shift);
+ page = realpage & chip->pagemask;
+
+ col = (int)(from & (mtd->writesize - 1));
+
+ buf = ops->datbuf;
+ oob = ops->oobbuf;
+ oob_required = oob ? 1 : 0;
+
+ while (1) {
+ bytes = min(mtd->writesize - col, readlen);
+ aligned = (bytes == mtd->writesize);
+
+ /* Is the current page in the buffer? */
+ if (realpage != chip->pagebuf || oob) {
+ bufpoi = aligned ? buf : chip->buffers->databuf;
+
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page);
+
+ /*
+ * Now read the page into the buffer. Absent an error,
+ * the read methods return max bitflips per ecc step.
+ */
+ if (unlikely(ops->mode == MTD_OPS_RAW))
+ ret = chip->ecc.read_page_raw(mtd, chip, bufpoi,
+ oob_required,
+ page);
+ else if (!aligned && NAND_HAS_SUBPAGE_READ(chip) &&
+ !oob)
+ ret = chip->ecc.read_subpage(mtd, chip,
+ col, bytes, bufpoi);
+ else
+ ret = chip->ecc.read_page(mtd, chip, bufpoi,
+ oob_required, page);
+ if (ret < 0) {
+ if (!aligned)
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+ break;
+ }
+
+ max_bitflips = max_t(unsigned int, max_bitflips, ret);
+
+ /* Transfer not aligned data */
+ if (!aligned) {
+ if (!NAND_HAS_SUBPAGE_READ(chip) && !oob &&
+ !(mtd->ecc_stats.failed - stats.failed) &&
+ (ops->mode != MTD_OPS_RAW)) {
+ chip->pagebuf = realpage;
+ chip->pagebuf_bitflips = ret;
+ } else {
+ /* Invalidate page cache */
+ chip->pagebuf = -1;
+ }
+ memcpy(buf, chip->buffers->databuf + col, bytes);
+ }
+
+ buf += bytes;
+
+ if (unlikely(oob)) {
+ int toread = min(oobreadlen, max_oobsize);
+
+ if (toread) {
+ oob = nand_transfer_oob(chip,
+ oob, ops, toread);
+ oobreadlen -= toread;
+ }
+ }
+
+ if (chip->options & NAND_NEED_READRDY) {
+ /* Apply delay or wait for ready/busy pin */
+ if (!chip->dev_ready)
+ udelay(chip->chip_delay);
+ else
nand_wait_ready(mtd);
}
} else {
memcpy(buf, chip->buffers->databuf + col, bytes);
buf += bytes;
+ max_bitflips = max_t(unsigned int, max_bitflips,
+ chip->pagebuf_bitflips);
}
readlen -= bytes;
@@ -750,7 +1438,7 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
if (!readlen)
break;
- /* For subsequent reads align to page boundary. */
+ /* For subsequent reads align to page boundary */
col = 0;
/* Increment page address */
realpage++;
@@ -762,231 +1450,1247 @@ static int nand_do_read_ops(struct mtd_info *mtd, loff_t from,
chip->select_chip(mtd, -1);
chip->select_chip(mtd, chipnr);
}
-
- /* Check, if the chip supports auto page increment
- * or if we have hit a block boundary.
- */
- if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck))
- sndcmd = 1;
}
+ chip->select_chip(mtd, -1);
ops->retlen = ops->len - (size_t) readlen;
if (oob)
ops->oobretlen = ops->ooblen - oobreadlen;
- if (ret)
+ if (ret < 0)
return ret;
if (mtd->ecc_stats.failed - stats.failed)
return -EBADMSG;
- return 0;
+ return max_bitflips;
+}
+
+/**
+ * nand_read - [MTD Interface] MTD compatibility function for nand_do_read_ecc
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @len: number of bytes to read
+ * @retlen: pointer to variable to store the number of read bytes
+ * @buf: the databuffer to put data
+ *
+ * Get hold of the chip and call nand_do_read.
+ */
+static int nand_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, uint8_t *buf)
+{
+ struct mtd_oob_ops ops;
+ int ret;
+
+ nand_get_device(mtd, FL_READING);
+ ops.len = len;
+ ops.datbuf = buf;
+ ops.oobbuf = NULL;
+ ops.mode = MTD_OPS_PLACE_OOB;
+ ret = nand_do_read_ops(mtd, from, &ops);
+ *retlen = ops.retlen;
+ nand_release_device(mtd);
+ return ret;
+}
+
+/**
+ * nand_read_oob_std - [REPLACEABLE] the most common OOB data read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to read
+ */
+static __maybe_unused int nand_read_oob_std(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ if (!IS_ENABLED(CONFIG_NAND_READ_OOB))
+ return -ENOTSUPP;
+
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+ return 0;
+}
+
+/**
+ * nand_read_oob_syndrome - [REPLACEABLE] OOB data read function for HW ECC
+ * with syndromes
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to read
+ */
+static __maybe_unused int nand_read_oob_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ uint8_t *buf = chip->oob_poi;
+ int length = mtd->oobsize;
+ int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad;
+ int eccsize = chip->ecc.size;
+ uint8_t *bufpoi = buf;
+ int i, toread, sndrnd = 0, pos;
+
+ if (!IS_ENABLED(CONFIG_NAND_READ_OOB))
+ return -ENOTSUPP;
+
+ chip->cmdfunc(mtd, NAND_CMD_READ0, chip->ecc.size, page);
+ for (i = 0; i < chip->ecc.steps; i++) {
+ if (sndrnd) {
+ pos = eccsize + i * (eccsize + chunk);
+ if (mtd->writesize > 512)
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, pos, -1);
+ else
+ chip->cmdfunc(mtd, NAND_CMD_READ0, pos, page);
+ } else
+ sndrnd = 1;
+ toread = min_t(int, length, chunk);
+ chip->read_buf(mtd, bufpoi, toread);
+ bufpoi += toread;
+ length -= toread;
+ }
+ if (length > 0)
+ chip->read_buf(mtd, bufpoi, length);
+
+ return 0;
+}
+
+/**
+ * nand_write_oob_std - [REPLACEABLE] the most common OOB data write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to write
+ */
+static __maybe_unused int nand_write_oob_std(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ int status = 0;
+ const uint8_t *buf = chip->oob_poi;
+ int length = mtd->oobsize;
+
+ if (!IS_ENABLED(CONFIG_NAND_READ_OOB) || !IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page);
+ chip->write_buf(mtd, buf, length);
+ /* Send command to program the OOB data */
+ chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+
+ status = chip->waitfunc(mtd, chip);
+
+ return status & NAND_STATUS_FAIL ? -EIO : 0;
+}
+
+/**
+ * nand_write_oob_syndrome - [REPLACEABLE] OOB data write function for HW ECC
+ * with syndrome - only for large page flash
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @page: page number to write
+ */
+static __maybe_unused int nand_write_oob_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip, int page)
+{
+ int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad;
+ int eccsize = chip->ecc.size, length = mtd->oobsize;
+ int i, len, pos, status = 0, sndcmd = 0, steps = chip->ecc.steps;
+ const uint8_t *bufpoi = chip->oob_poi;
+
+ if (!IS_ENABLED(CONFIG_NAND_READ_OOB) || !IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ /*
+ * data-ecc-data-ecc ... ecc-oob
+ * or
+ * data-pad-ecc-pad-data-pad .... ecc-pad-oob
+ */
+ if (!chip->ecc.prepad && !chip->ecc.postpad) {
+ pos = steps * (eccsize + chunk);
+ steps = 0;
+ } else
+ pos = eccsize;
+
+ chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page);
+ for (i = 0; i < steps; i++) {
+ if (sndcmd) {
+ if (mtd->writesize <= 512) {
+ uint32_t fill = 0xFFFFFFFF;
+
+ len = eccsize;
+ while (len > 0) {
+ int num = min_t(int, len, 4);
+ chip->write_buf(mtd, (uint8_t *)&fill,
+ num);
+ len -= num;
+ }
+ } else {
+ pos = eccsize + i * (eccsize + chunk);
+ chip->cmdfunc(mtd, NAND_CMD_RNDIN, pos, -1);
+ }
+ } else
+ sndcmd = 1;
+ len = min_t(int, length, chunk);
+ chip->write_buf(mtd, bufpoi, len);
+ bufpoi += len;
+ length -= len;
+ }
+ if (length > 0)
+ chip->write_buf(mtd, bufpoi, length);
+
+ chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+ status = chip->waitfunc(mtd, chip);
+
+ return status & NAND_STATUS_FAIL ? -EIO : 0;
+}
+
+/**
+ * nand_do_read_oob - [INTERN] NAND read out-of-band
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob operations description structure
+ *
+ * NAND read out-of-band data from the spare area.
+ */
+static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
+ struct mtd_oob_ops *ops)
+{
+ int page, realpage, chipnr;
+ struct nand_chip *chip = mtd->priv;
+ struct mtd_ecc_stats stats;
+ int readlen = ops->ooblen;
+ int len;
+ uint8_t *buf = ops->oobbuf;
+ int ret = 0;
+
+ if (!IS_ENABLED(CONFIG_NAND_READ_OOB))
+ return -ENOTSUPP;
+
+ pr_debug("%s: from = 0x%08Lx, len = %i\n",
+ __func__, (unsigned long long)from, readlen);
+
+ stats = mtd->ecc_stats;
+
+ if (ops->mode == MTD_OPS_AUTO_OOB)
+ len = chip->ecc.layout->oobavail;
+ else
+ len = mtd->oobsize;
+
+ if (unlikely(ops->ooboffs >= len)) {
+ pr_debug("%s: attempt to start read outside oob\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ /* Do not allow reads past end of device */
+ if (unlikely(from >= mtd->size ||
+ ops->ooboffs + readlen > ((mtd->size >> chip->page_shift) -
+ (from >> chip->page_shift)) * len)) {
+ pr_debug("%s: attempt to read beyond end of device\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ chipnr = (int)(from >> chip->chip_shift);
+ chip->select_chip(mtd, chipnr);
+
+ /* Shift to get page */
+ realpage = (int)(from >> chip->page_shift);
+ page = realpage & chip->pagemask;
+
+ while (1) {
+ if (ops->mode == MTD_OPS_RAW)
+ ret = chip->ecc.read_oob_raw(mtd, chip, page);
+ else
+ ret = chip->ecc.read_oob(mtd, chip, page);
+
+ if (ret < 0)
+ break;
+
+ len = min(len, readlen);
+ buf = nand_transfer_oob(chip, buf, ops, len);
+
+ if (chip->options & NAND_NEED_READRDY) {
+ /* Apply delay or wait for ready/busy pin */
+ if (!chip->dev_ready)
+ udelay(chip->chip_delay);
+ else
+ nand_wait_ready(mtd);
+ }
+
+ readlen -= len;
+ if (!readlen)
+ break;
+
+ /* Increment page address */
+ realpage++;
+
+ page = realpage & chip->pagemask;
+ /* Check, if we cross a chip boundary */
+ if (!page) {
+ chipnr++;
+ chip->select_chip(mtd, -1);
+ chip->select_chip(mtd, chipnr);
+ }
+ }
+ chip->select_chip(mtd, -1);
+
+ ops->oobretlen = ops->ooblen - readlen;
+
+ if (ret < 0)
+ return ret;
+
+ if (mtd->ecc_stats.failed - stats.failed)
+ return -EBADMSG;
+
+ return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0;
+}
+
+/**
+ * nand_read_oob - [MTD Interface] NAND read data and/or out-of-band
+ * @mtd: MTD device structure
+ * @from: offset to read from
+ * @ops: oob operation description structure
+ *
+ * NAND read data and/or out-of-band data.
+ */
+static int nand_read_oob(struct mtd_info *mtd, loff_t from,
+ struct mtd_oob_ops *ops)
+{
+ int ret = -ENOTSUPP;
+
+ if (!IS_ENABLED(CONFIG_NAND_READ_OOB))
+ return -ENOTSUPP;
+
+ ops->retlen = 0;
+
+ /* Do not allow reads past end of device */
+ if (ops->datbuf && (from + ops->len) > mtd->size) {
+ pr_debug("%s: attempt to read beyond end of device\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ nand_get_device(mtd, FL_READING);
+
+ switch (ops->mode) {
+ case MTD_OPS_PLACE_OOB:
+ case MTD_OPS_AUTO_OOB:
+ case MTD_OPS_RAW:
+ break;
+
+ default:
+ goto out;
+ }
+
+ if (!ops->datbuf)
+ ret = nand_do_read_oob(mtd, from, ops);
+ else
+ ret = nand_do_read_ops(mtd, from, ops);
+
+out:
+ nand_release_device(mtd);
+ return ret;
+}
+
+
+/**
+ * nand_write_page_raw - [INTERN] raw page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
+ *
+ * Not for syndrome calculating ECC controllers, which use a special oob layout.
+ */
+static __maybe_unused int nand_write_page_raw(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf, int oob_required)
+{
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ chip->write_buf(mtd, buf, mtd->writesize);
+ if (oob_required)
+ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
+}
+
+/**
+ * nand_write_page_raw_syndrome - [INTERN] raw page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
+ *
+ * We need a special oob layout and handling even when ECC isn't checked.
+ */
+static __maybe_unused int nand_write_page_raw_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
+{
+ int eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ uint8_t *oob = chip->oob_poi;
+ int steps, size;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ for (steps = chip->ecc.steps; steps > 0; steps--) {
+ chip->write_buf(mtd, buf, eccsize);
+ buf += eccsize;
+
+ if (chip->ecc.prepad) {
+ chip->write_buf(mtd, oob, chip->ecc.prepad);
+ oob += chip->ecc.prepad;
+ }
+
+ chip->read_buf(mtd, oob, eccbytes);
+ oob += eccbytes;
+
+ if (chip->ecc.postpad) {
+ chip->write_buf(mtd, oob, chip->ecc.postpad);
+ oob += chip->ecc.postpad;
+ }
+ }
+
+ size = mtd->oobsize - (oob - chip->oob_poi);
+ if (size)
+ chip->write_buf(mtd, oob, size);
+
+ return 0;
+}
+/**
+ * nand_write_page_swecc - [REPLACEABLE] software ECC based page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
+ */
+static __maybe_unused int nand_write_page_swecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf, int oob_required)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ const uint8_t *p = buf;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ /* Software ECC calculation */
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ chip->oob_poi[eccpos[i]] = ecc_calc[i];
+
+ return chip->ecc.write_page_raw(mtd, chip, buf, 1);
+}
+
+/**
+ * nand_write_page_hwecc - [REPLACEABLE] hardware ECC based page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
+ */
+static __maybe_unused int nand_write_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf, int oob_required)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ const uint8_t *p = buf;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
+ chip->write_buf(mtd, p, eccsize);
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+ }
+
+ for (i = 0; i < chip->ecc.total; i++)
+ chip->oob_poi[eccpos[i]] = ecc_calc[i];
+
+ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
+}
+
+
+/**
+ * nand_write_subpage_hwecc - [REPLACABLE] hardware ECC based subpage write
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @column: column address of subpage within the page
+ * @data_len: data length
+ * @oob_required: must write chip->oob_poi to OOB
+ */
+static __maybe_unused int nand_write_subpage_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint32_t offset,
+ uint32_t data_len, const uint8_t *data_buf,
+ int oob_required)
+{
+ uint8_t *oob_buf = chip->oob_poi;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+ int ecc_size = chip->ecc.size;
+ int ecc_bytes = chip->ecc.bytes;
+ int ecc_steps = chip->ecc.steps;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ uint32_t start_step = offset / ecc_size;
+ uint32_t end_step = (offset + data_len - 1) / ecc_size;
+ int oob_bytes = mtd->oobsize / ecc_steps;
+ int step, i;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ for (step = 0; step < ecc_steps; step++) {
+ /* configure controller for WRITE access */
+ chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
+
+ /* write data (untouched subpages already masked by 0xFF) */
+ chip->write_buf(mtd, data_buf, ecc_size);
+
+ /* mask ECC of un-touched subpages by padding 0xFF */
+ if ((step < start_step) || (step > end_step))
+ memset(ecc_calc, 0xff, ecc_bytes);
+ else
+ chip->ecc.calculate(mtd, data_buf, ecc_calc);
+
+ /* mask OOB of un-touched subpages by padding 0xFF */
+ /* if oob_required, preserve OOB metadata of written subpage */
+ if (!oob_required || (step < start_step) || (step > end_step))
+ memset(oob_buf, 0xff, oob_bytes);
+
+ data_buf += ecc_size;
+ ecc_calc += ecc_bytes;
+ oob_buf += oob_bytes;
+ }
+
+ /* copy calculated ECC for whole page to chip->buffer->oob */
+ /* this include masked-value(0xFF) for unwritten subpages */
+ ecc_calc = chip->buffers->ecccalc;
+ for (i = 0; i < chip->ecc.total; i++)
+ chip->oob_poi[eccpos[i]] = ecc_calc[i];
+
+ /* write OOB buffer to NAND device */
+ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
+}
+
+
+/**
+ * nand_write_page_syndrome - [REPLACEABLE] hardware ECC syndrome based page write
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ * @oob_required: must write chip->oob_poi to OOB
+ *
+ * The hw generator calculates the error syndrome automatically. Therefore we
+ * need a special oob layout and handling.
+ */
+static __maybe_unused int nand_write_page_syndrome(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const uint8_t *buf, int oob_required)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ const uint8_t *p = buf;
+ uint8_t *oob = chip->oob_poi;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+
+ chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
+ chip->write_buf(mtd, p, eccsize);
+
+ if (chip->ecc.prepad) {
+ chip->write_buf(mtd, oob, chip->ecc.prepad);
+ oob += chip->ecc.prepad;
+ }
+
+ chip->ecc.calculate(mtd, p, oob);
+ chip->write_buf(mtd, oob, eccbytes);
+ oob += eccbytes;
+
+ if (chip->ecc.postpad) {
+ chip->write_buf(mtd, oob, chip->ecc.postpad);
+ oob += chip->ecc.postpad;
+ }
+ }
+
+ /* Calculate remaining oob bytes */
+ i = mtd->oobsize - (oob - chip->oob_poi);
+ if (i)
+ chip->write_buf(mtd, oob, i);
+
+ return 0;
+}
+
+/**
+ * nand_write_page - [REPLACEABLE] write one page
+ * @mtd: MTD device structure
+ * @chip: NAND chip descriptor
+ * @offset: address offset within the page
+ * @data_len: length of actual data to be written
+ * @buf: the data to write
+ * @oob_required: must write chip->oob_poi to OOB
+ * @page: page number to write
+ * @cached: cached programming
+ * @raw: use _raw version of write_page
+ */
+static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
+ uint32_t offset, int data_len, const uint8_t *buf,
+ int oob_required, int page, int cached, int raw)
+{
+ int status, subpage;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ if (!(chip->options & NAND_NO_SUBPAGE_WRITE) &&
+ chip->ecc.write_subpage)
+ subpage = offset || (data_len < mtd->writesize);
+ else
+ subpage = 0;
+
+ chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page);
+
+ if (unlikely(raw))
+ status = chip->ecc.write_page_raw(mtd, chip, buf,
+ oob_required);
+ else if (subpage)
+ status = chip->ecc.write_subpage(mtd, chip, offset, data_len,
+ buf, oob_required);
+ else
+ status = chip->ecc.write_page(mtd, chip, buf, oob_required);
+
+ if (status < 0)
+ return status;
+
+ /*
+ * Cached progamming disabled for now. Not sure if it's worth the
+ * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s).
+ */
+ cached = 0;
+
+ if (!cached || !NAND_HAS_CACHEPROG(chip)) {
+
+ chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
+ status = chip->waitfunc(mtd, chip);
+ /*
+ * See if operation failed and additional status checks are
+ * available.
+ */
+ if ((status & NAND_STATUS_FAIL) && (chip->errstat))
+ status = chip->errstat(mtd, chip, FL_WRITING, status,
+ page);
+
+ if (status & NAND_STATUS_FAIL)
+ return -EIO;
+ } else {
+ chip->cmdfunc(mtd, NAND_CMD_CACHEDPROG, -1, -1);
+ status = chip->waitfunc(mtd, chip);
+ }
+
+ return 0;
+}
+
+/**
+ * nand_fill_oob - [INTERN] Transfer client buffer to oob
+ * @mtd: MTD device structure
+ * @oob: oob data buffer
+ * @len: oob data write length
+ * @ops: oob ops structure
+ */
+static uint8_t *nand_fill_oob(struct mtd_info *mtd, uint8_t *oob, size_t len,
+ struct mtd_oob_ops *ops)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ /*
+ * Initialise to all 0xFF, to avoid the possibility of left over OOB
+ * data from a previous OOB read.
+ */
+ memset(chip->oob_poi, 0xff, mtd->oobsize);
+
+ switch (ops->mode) {
+
+ case MTD_OPS_PLACE_OOB:
+ case MTD_OPS_RAW:
+ memcpy(chip->oob_poi + ops->ooboffs, oob, len);
+ return oob + len;
+
+ case MTD_OPS_AUTO_OOB: {
+ struct nand_oobfree *free = chip->ecc.layout->oobfree;
+ uint32_t boffs = 0, woffs = ops->ooboffs;
+ size_t bytes = 0;
+
+ for (; free->length && len; free++, len -= bytes) {
+ /* Write request not from offset 0? */
+ if (unlikely(woffs)) {
+ if (woffs >= free->length) {
+ woffs -= free->length;
+ continue;
+ }
+ boffs = free->offset + woffs;
+ bytes = min_t(size_t, len,
+ (free->length - woffs));
+ woffs = 0;
+ } else {
+ bytes = min_t(size_t, len, free->length);
+ boffs = free->offset;
+ }
+ memcpy(chip->oob_poi + boffs, oob, bytes);
+ oob += bytes;
+ }
+ return oob;
+ }
+ default:
+ BUG();
+ }
+ return NULL;
+}
+
+#define NOTALIGNED(x) ((x & (chip->subpagesize - 1)) != 0)
+
+/**
+ * nand_do_write_ops - [INTERN] NAND write with ECC
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operations description structure
+ *
+ * NAND write with ECC.
+ */
+static int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
+ struct mtd_oob_ops *ops)
+{
+ int chipnr, realpage, page, blockmask, column;
+ struct nand_chip *chip = mtd->priv;
+ uint32_t writelen = ops->len;
+
+ uint32_t oobwritelen = ops->ooblen;
+ uint32_t oobmaxlen = ops->mode == MTD_OPS_AUTO_OOB ?
+ mtd->oobavail : mtd->oobsize;
+
+ uint8_t *oob = ops->oobbuf;
+ uint8_t *buf = ops->datbuf;
+ int ret;
+ int oob_required = oob ? 1 : 0;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ ops->retlen = 0;
+ if (!writelen)
+ return 0;
+
+ column = to & (mtd->writesize - 1);
+
+ chipnr = (int)(to >> chip->chip_shift);
+ chip->select_chip(mtd, chipnr);
+
+ /* Check, if it is write protected */
+ if (nand_check_wp(mtd)) {
+ ret = -EIO;
+ goto err_out;
+ }
+
+ realpage = (int)(to >> chip->page_shift);
+ page = realpage & chip->pagemask;
+ blockmask = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
+
+ /* Invalidate the page cache, when we write to the cached page */
+ if (to <= (chip->pagebuf << chip->page_shift) &&
+ (chip->pagebuf << chip->page_shift) < (to + ops->len))
+ chip->pagebuf = -1;
+
+ /* Don't allow multipage oob writes with offset */
+ if (oob && ops->ooboffs && (ops->ooboffs + ops->ooblen > oobmaxlen)) {
+ ret = -EINVAL;
+ goto err_out;
+ }
+
+ while (1) {
+ int bytes = mtd->writesize;
+ int cached = writelen > bytes && page != blockmask;
+ uint8_t *wbuf = buf;
+
+ /* Partial page write? */
+ if (unlikely(column || writelen < (mtd->writesize - 1))) {
+ cached = 0;
+ bytes = min_t(int, bytes - column, (int) writelen);
+ chip->pagebuf = -1;
+ memset(chip->buffers->databuf, 0xff, mtd->writesize);
+ memcpy(&chip->buffers->databuf[column], buf, bytes);
+ wbuf = chip->buffers->databuf;
+ }
+
+ if (unlikely(oob)) {
+ size_t len = min(oobwritelen, oobmaxlen);
+ oob = nand_fill_oob(mtd, oob, len, ops);
+ oobwritelen -= len;
+ } else {
+ /* We still need to erase leftover OOB data */
+ memset(chip->oob_poi, 0xff, mtd->oobsize);
+ }
+
+ if (oob || !mtd_all_ff(wbuf, mtd->writesize)) {
+ ret = chip->write_page(mtd, chip, column, bytes, wbuf,
+ oob_required, page, cached,
+ (ops->mode == MTD_OPS_RAW));
+ if (ret)
+ break;
+ }
+
+ writelen -= bytes;
+ if (!writelen)
+ break;
+
+ column = 0;
+ buf += bytes;
+ realpage++;
+
+ page = realpage & chip->pagemask;
+ /* Check, if we cross a chip boundary */
+ if (!page) {
+ chipnr++;
+ chip->select_chip(mtd, -1);
+ chip->select_chip(mtd, chipnr);
+ }
+ }
+
+ ops->retlen = ops->len - writelen;
+ if (unlikely(oob))
+ ops->oobretlen = ops->ooblen;
+
+err_out:
+ chip->select_chip(mtd, -1);
+ return ret;
+}
+
+/**
+ * nand_write - [MTD Interface] NAND write with ECC
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @len: number of bytes to write
+ * @retlen: pointer to variable to store the number of written bytes
+ * @buf: the data to write
+ *
+ * NAND write with ECC.
+ */
+static int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const uint8_t *buf)
+{
+ struct mtd_oob_ops ops;
+ int ret;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ nand_get_device(mtd, FL_WRITING);
+ ops.len = len;
+ ops.datbuf = (uint8_t *)buf;
+ ops.oobbuf = NULL;
+ ops.mode = MTD_OPS_PLACE_OOB;
+ ret = nand_do_write_ops(mtd, to, &ops);
+ *retlen = ops.retlen;
+ nand_release_device(mtd);
+ return ret;
+}
+
+/**
+ * nand_do_write_oob - [MTD Interface] NAND write out-of-band
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operation description structure
+ *
+ * NAND write out-of-band.
+ */
+static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
+ struct mtd_oob_ops *ops)
+{
+ int chipnr, page, status, len;
+ struct nand_chip *chip = mtd->priv;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ pr_debug("%s: to = 0x%08x, len = %i\n",
+ __func__, (unsigned int)to, (int)ops->ooblen);
+
+ if (ops->mode == MTD_OPS_AUTO_OOB)
+ len = chip->ecc.layout->oobavail;
+ else
+ len = mtd->oobsize;
+
+ /* Do not allow write past end of page */
+ if ((ops->ooboffs + ops->ooblen) > len) {
+ pr_debug("%s: attempt to write past end of page\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ if (unlikely(ops->ooboffs >= len)) {
+ pr_debug("%s: attempt to start write outside oob\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ /* Do not allow write past end of device */
+ if (unlikely(to >= mtd->size ||
+ ops->ooboffs + ops->ooblen >
+ ((mtd->size >> chip->page_shift) -
+ (to >> chip->page_shift)) * len)) {
+ pr_debug("%s: attempt to write beyond end of device\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ chipnr = (int)(to >> chip->chip_shift);
+ chip->select_chip(mtd, chipnr);
+
+ /* Shift to get page */
+ page = (int)(to >> chip->page_shift);
+
+ /*
+ * Reset the chip. Some chips (like the Toshiba TC5832DC found in one
+ * of my DiskOnChip 2000 test units) will clear the whole data page too
+ * if we don't do this. I have no clue why, but I seem to have 'fixed'
+ * it in the doc2000 driver in August 1999. dwmw2.
+ */
+ chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+
+ /* Check, if it is write protected */
+ if (nand_check_wp(mtd)) {
+ chip->select_chip(mtd, -1);
+ return -EROFS;
+ }
+
+ /* Invalidate the page cache, if we write to the cached page */
+ if (page == chip->pagebuf)
+ chip->pagebuf = -1;
+
+ nand_fill_oob(mtd, ops->oobbuf, ops->ooblen, ops);
+
+ if (ops->mode == MTD_OPS_RAW)
+ status = chip->ecc.write_oob_raw(mtd, chip, page & chip->pagemask);
+ else
+ status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
+
+ chip->select_chip(mtd, -1);
+
+ if (status)
+ return status;
+
+ ops->oobretlen = ops->ooblen;
+
+ return 0;
+}
+
+/**
+ * nand_write_oob - [MTD Interface] NAND write data and/or out-of-band
+ * @mtd: MTD device structure
+ * @to: offset to write to
+ * @ops: oob operation description structure
+ */
+static int nand_write_oob(struct mtd_info *mtd, loff_t to,
+ struct mtd_oob_ops *ops)
+{
+ int ret = -ENOTSUPP;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ ops->retlen = 0;
+
+ /* Do not allow writes past end of device */
+ if (ops->datbuf && (to + ops->len) > mtd->size) {
+ pr_debug("%s: attempt to write beyond end of device\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ nand_get_device(mtd, FL_WRITING);
+
+ switch (ops->mode) {
+ case MTD_OPS_PLACE_OOB:
+ case MTD_OPS_AUTO_OOB:
+ case MTD_OPS_RAW:
+ break;
+
+ default:
+ goto out;
+ }
+
+ if (!ops->datbuf)
+ ret = nand_do_write_oob(mtd, to, ops);
+ else
+ ret = nand_do_write_ops(mtd, to, ops);
+
+out:
+ nand_release_device(mtd);
+ return ret;
}
/**
- * nand_read - [MTD Interface] MTD compability function for nand_do_read_ecc
- * @mtd: MTD device structure
- * @from: offset to read from
- * @len: number of bytes to read
- * @retlen: pointer to variable to store the number of read bytes
- * @buf: the databuffer to put data
+ * single_erase_cmd - [GENERIC] NAND standard block erase command function
+ * @mtd: MTD device structure
+ * @page: the page address of the block which will be erased
*
- * Get hold of the chip and call nand_do_read
+ * Standard erase command for NAND chips.
*/
-static int nand_read(struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, uint8_t *buf)
+static void single_erase_cmd(struct mtd_info *mtd, int page)
{
struct nand_chip *chip = mtd->priv;
- int ret;
-
- /* Do not allow reads past end of device */
- if ((from + len) > mtd->size)
- return -EINVAL;
- if (!len)
- return 0;
-
- chip->ops.len = len;
- chip->ops.datbuf = buf;
- chip->ops.oobbuf = NULL;
- ret = nand_do_read_ops(mtd, from, &chip->ops);
-
- *retlen = chip->ops.retlen;
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return;
- return ret;
+ /* Send commands to erase a block */
+ chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page);
+ chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
}
/**
- * nand_read_oob_std - [REPLACABLE] the most common OOB data read function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @page: page number to read
- * @sndcmd: flag whether to issue read command or not
+ * nand_erase - [MTD Interface] erase block(s)
+ * @mtd: MTD device structure
+ * @instr: erase instruction
+ *
+ * Erase one ore more blocks.
*/
-int nand_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip,
- int page, int sndcmd)
+static int nand_erase(struct mtd_info *mtd, struct erase_info *instr)
{
- if (sndcmd) {
- chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
- sndcmd = 0;
- }
- chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
- return sndcmd;
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ return nand_erase_nand(mtd, instr, 0);
}
/**
- * nand_do_read_oob - [Intern] NAND read out-of-band
- * @mtd: MTD device structure
- * @from: offset to read from
- * @ops: oob operations description structure
+ * nand_erase_nand - [INTERN] erase block(s)
+ * @mtd: MTD device structure
+ * @instr: erase instruction
+ * @allowbbt: allow erasing the bbt area
*
- * NAND read out-of-band data from the spare area
+ * Erase one ore more blocks.
*/
-#ifdef CONFIG_NAND_READ_OOB
-static int nand_do_read_oob(struct mtd_info *mtd, loff_t from,
- struct mtd_oob_ops *ops)
+int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
+ int allowbbt)
{
- int page, realpage, chipnr, sndcmd = 1;
+ int page, status, pages_per_block, ret, chipnr;
struct nand_chip *chip = mtd->priv;
- int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
- int readlen = ops->ooblen;
- int len;
- uint8_t *buf = ops->oobbuf;
+ loff_t len;
- MTD_DEBUG(MTD_DEBUG_LEVEL3, "nand_read_oob: from = 0x%08Lx, len = %i\n",
- (unsigned long long)from, readlen);
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
- if (ops->mode == MTD_OPS_AUTO_OOB)
- len = chip->ecc.layout->oobavail;
- else
- len = mtd->oobsize;
+ pr_debug("%s: start = 0x%012llx, len = %llu\n",
+ __func__, (unsigned long long)instr->addr,
+ (unsigned long long)instr->len);
- if (unlikely(ops->ooboffs >= len)) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt to start read outside oob\n");
+ if (check_offs_len(mtd, instr->addr, instr->len))
return -EINVAL;
- }
- /* Do not allow reads past end of device */
- if (unlikely(from >= mtd->size ||
- ops->ooboffs + readlen > ((mtd->size >> chip->page_shift) -
- (from >> chip->page_shift)) * len)) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt read beyond end of device\n");
- return -EINVAL;
- }
+ /* Grab the lock and see if the device is available */
+ nand_get_device(mtd, FL_ERASING);
- chipnr = (int)(from >> chip->chip_shift);
+ /* Shift to get first page */
+ page = (int)(instr->addr >> chip->page_shift);
+ chipnr = (int)(instr->addr >> chip->chip_shift);
+
+ /* Calculate pages in each block */
+ pages_per_block = 1 << (chip->phys_erase_shift - chip->page_shift);
+
+ /* Select the NAND device */
chip->select_chip(mtd, chipnr);
- /* Shift to get page */
- realpage = (int)(from >> chip->page_shift);
- page = realpage & chip->pagemask;
+ /* Check, if it is write protected */
+ if (nand_check_wp(mtd)) {
+ pr_debug("%s: device is write protected!\n",
+ __func__);
+ instr->state = MTD_ERASE_FAILED;
+ goto erase_exit;
+ }
- while(1) {
- sndcmd = chip->ecc.read_oob(mtd, chip, page, sndcmd);
+ /* Loop through the pages */
+ len = instr->len;
- len = min(len, readlen);
- buf = nand_transfer_oob(chip, buf, ops, len);
+ instr->state = MTD_ERASING;
- if (!(chip->options & NAND_NO_READRDY)) {
- /*
- * Apply delay or wait for ready/busy pin. Do this
- * before the AUTOINCR check, so no problems arise if a
- * chip which does auto increment is marked as
- * NOAUTOINCR by the board driver.
- */
- if (!chip->dev_ready)
- udelay(chip->chip_delay);
- else
- nand_wait_ready(mtd);
+ while (len) {
+ /* Check if we have a bad block, we do not erase bad blocks! */
+ if (!mtd->allow_erasebad &&
+ nand_block_checkbad(mtd, ((loff_t) page) <<
+ chip->page_shift, 0, allowbbt)) {
+ pr_warn("%s: attempt to erase a bad block at page 0x%08x\n",
+ __func__, page);
+ instr->state = MTD_ERASE_FAILED;
+ goto erase_exit;
}
- readlen -= len;
- if (!readlen)
- break;
+ /*
+ * Invalidate the page cache, if we erase the block which
+ * contains the current cached page.
+ */
+ if (page <= chip->pagebuf && chip->pagebuf <
+ (page + pages_per_block))
+ chip->pagebuf = -1;
- /* Increment page address */
- realpage++;
+ chip->erase_cmd(mtd, page & chip->pagemask);
+
+ status = chip->waitfunc(mtd, chip);
+
+ /*
+ * See if operation failed and additional status checks are
+ * available
+ */
+ if ((status & NAND_STATUS_FAIL) && (chip->errstat))
+ status = chip->errstat(mtd, chip, FL_ERASING,
+ status, page);
+
+ /* See if block erase succeeded */
+ if (status & NAND_STATUS_FAIL) {
+ pr_debug("%s: failed erase, page 0x%08x\n",
+ __func__, page);
+ instr->state = MTD_ERASE_FAILED;
+ instr->fail_addr =
+ ((loff_t)page << chip->page_shift);
+ goto erase_exit;
+ }
+
+ /* Increment page address and decrement length */
+ len -= (1 << chip->phys_erase_shift);
+ page += pages_per_block;
- page = realpage & chip->pagemask;
/* Check, if we cross a chip boundary */
- if (!page) {
+ if (len && !(page & chip->pagemask)) {
chipnr++;
chip->select_chip(mtd, -1);
chip->select_chip(mtd, chipnr);
}
-
- /* Check, if the chip supports auto page increment
- * or if we have hit a block boundary.
- */
- if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck))
- sndcmd = 1;
}
+ instr->state = MTD_ERASE_DONE;
- ops->oobretlen = ops->ooblen;
- return 0;
+erase_exit:
+
+ ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO;
+
+ /* Deselect and wake up anyone waiting on the device */
+ chip->select_chip(mtd, -1);
+ nand_release_device(mtd);
+
+ /* Do call back function */
+ if (!ret)
+ mtd_erase_callback(instr);
+
+ /* Return more or less happy */
+ return ret;
}
/**
- * nand_read_oob - [MTD Interface] NAND read data and/or out-of-band
- * @mtd: MTD device structure
- * @from: offset to read from
- * @ops: oob operation description structure
+ * nand_sync - [MTD Interface] sync
+ * @mtd: MTD device structure
*
- * NAND read data and/or out-of-band data
+ * Sync is actually a wait for chip ready function.
*/
-static int nand_read_oob(struct mtd_info *mtd, loff_t from,
- struct mtd_oob_ops *ops)
+static void nand_sync(struct mtd_info *mtd)
{
- int ret = -ENOSYS;
+ pr_debug("%s: called\n", __func__);
- ops->retlen = 0;
+ /* Grab the lock and see if the device is available */
+ nand_get_device(mtd, FL_SYNCING);
+ /* Release it and go back */
+ nand_release_device(mtd);
+}
- /* Do not allow reads past end of device */
- if (ops->datbuf && (from + ops->len) > mtd->size) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt read beyond end of device\n");
- return -EINVAL;
- }
+/**
+ * nand_block_isbad - [MTD Interface] Check if block at offset is bad
+ * @mtd: MTD device structure
+ * @offs: offset relative to mtd start
+ */
+static int nand_block_isbad(struct mtd_info *mtd, loff_t offs)
+{
+ return nand_block_checkbad(mtd, offs, 1, 0);
+}
- switch(ops->mode) {
- case MTD_OPS_PLACE_OOB:
- case MTD_OPS_AUTO_OOB:
- case MTD_OPS_RAW:
- break;
+/**
+ * nand_block_markbad - [MTD Interface] Mark block at the given offset as bad
+ * @mtd: MTD device structure
+ * @ofs: offset relative to mtd start
+ */
+static int nand_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+ struct nand_chip *chip = mtd->priv;
+ int ret;
- default:
- goto out;
- }
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
- if (!ops->datbuf)
- ret = nand_do_read_oob(mtd, from, ops);
- else
- ret = nand_do_read_ops(mtd, from, ops);
+ ret = nand_block_isbad(mtd, ofs);
+ if (ret) {
+ /* If it was bad already, return success and do nothing */
+ if (ret > 0)
+ return 0;
+ return ret;
+ }
- out:
- return ret;
+ return chip->block_markbad(mtd, ofs);
}
-#endif
/**
- * nand_block_isbad - [MTD Interface] Check if block at offset is bad
- * @mtd: MTD device structure
- * @offs: offset relative to mtd start
+ * nand_onfi_set_features- [REPLACEABLE] set features for ONFI nand
+ * @mtd: MTD device structure
+ * @chip: nand chip info structure
+ * @addr: feature address.
+ * @subfeature_param: the subfeature parameters, a four bytes array.
*/
-int nand_block_isbad(struct mtd_info *mtd, loff_t offs)
+static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip,
+ int addr, uint8_t *subfeature_param)
{
- /* Check for invalid offset */
- if (offs > mtd->size)
+ int status;
+
+ if (!chip->onfi_version)
return -EINVAL;
- return nand_block_checkbad(mtd, offs, 1, 0);
+ chip->cmdfunc(mtd, NAND_CMD_SET_FEATURES, addr, -1);
+ chip->write_buf(mtd, subfeature_param, ONFI_SUBFEATURE_PARAM_LEN);
+ status = chip->waitfunc(mtd, chip);
+ if (status & NAND_STATUS_FAIL)
+ return -EIO;
+ return 0;
}
-/*
- * Set default functions
+/**
+ * nand_onfi_get_features- [REPLACEABLE] get features for ONFI nand
+ * @mtd: MTD device structure
+ * @chip: nand chip info structure
+ * @addr: feature address.
+ * @subfeature_param: the subfeature parameters, a four bytes array.
*/
+static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip,
+ int addr, uint8_t *subfeature_param)
+{
+ if (!chip->onfi_version)
+ return -EINVAL;
+
+ /* clear the sub feature parameters */
+ memset(subfeature_param, 0, ONFI_SUBFEATURE_PARAM_LEN);
+
+ chip->cmdfunc(mtd, NAND_CMD_GET_FEATURES, addr, -1);
+ chip->read_buf(mtd, subfeature_param, ONFI_SUBFEATURE_PARAM_LEN);
+ return 0;
+}
+
+/* Set default functions */
static void nand_set_defaults(struct nand_chip *chip, int busw)
{
/* check for proper chip_delay setup, set 20us if not */
@@ -1003,7 +2707,7 @@ static void nand_set_defaults(struct nand_chip *chip, int busw)
if (!chip->select_chip)
chip->select_chip = nand_select_chip;
- if (!chip->read_byte || chip->read_byte == nand_read_byte)
+ if (!chip->read_byte)
chip->read_byte = busw ? nand_read_byte16 : nand_read_byte;
if (!chip->read_word)
chip->read_word = nand_read_word;
@@ -1012,13 +2716,11 @@ static void nand_set_defaults(struct nand_chip *chip, int busw)
#ifdef CONFIG_MTD_WRITE
if (!chip->block_markbad)
chip->block_markbad = nand_default_block_markbad;
- if (!chip->write_buf || chip->write_buf == nand_write_buf)
+ if (!chip->write_buf)
chip->write_buf = busw ? nand_write_buf16 : nand_write_buf;
#endif
- if (!chip->read_buf || chip->read_buf == nand_read_buf)
+ if (!chip->read_buf)
chip->read_buf = busw ? nand_read_buf16 : nand_read_buf;
- if (!chip->verify_buf || chip->verify_buf == nand_verify_buf)
- chip->verify_buf = busw ? nand_verify_buf16 : nand_verify_buf;
#ifdef CONFIG_NAND_BBT
if (!chip->scan_bbt)
chip->scan_bbt = nand_default_bbt;
@@ -1029,23 +2731,21 @@ static void nand_set_defaults(struct nand_chip *chip, int busw)
}
-/*
- * sanitize ONFI strings so we can safely print them
- */
-static void sanitize_string(char *s, size_t len)
+/* Sanitize ONFI strings so we can safely print them */
+static void sanitize_string(uint8_t *s, size_t len)
{
ssize_t i;
- /* null terminate */
+ /* Null terminate */
s[len - 1] = 0;
- /* remove non printable chars */
+ /* Remove non printable chars */
for (i = 0; i < len - 1; i++) {
if (s[i] < ' ' || s[i] > 127)
s[i] = '?';
}
- /* remove trailing spaces */
+ /* Remove trailing spaces */
strim(s);
}
@@ -1062,7 +2762,7 @@ static u16 onfi_crc16(u16 crc, u8 const *p, size_t len)
}
/*
- * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise
+ * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise.
*/
static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
int *busw)
@@ -1071,7 +2771,12 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
int i;
int val;
- /* try ONFI for unknow chip or LP */
+ /* ONFI need to be probed in 8 bits mode, and 16 bits should be selected with NAND_BUSWIDTH_AUTO */
+ if (chip->options & NAND_BUSWIDTH_16) {
+ pr_err("Trying ONFI probe in 16 bits mode, aborting !\n");
+ return 0;
+ }
+ /* Try ONFI for unknown chip or LP */
chip->cmdfunc(mtd, NAND_CMD_READID, 0x20, -1);
if (chip->read_byte(mtd) != 'O' || chip->read_byte(mtd) != 'N' ||
chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I')
@@ -1090,7 +2795,7 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
if (i == 3)
return 0;
- /* check version */
+ /* Check version */
val = le16_to_cpu(p->revision);
if (val & (1 << 5))
chip->onfi_version = 23;
@@ -1102,11 +2807,9 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
chip->onfi_version = 20;
else if (val & (1 << 1))
chip->onfi_version = 10;
- else
- chip->onfi_version = 0;
if (!chip->onfi_version) {
- pr_info("unsupported ONFI version: %d\n", val);
+ pr_info("%s: unsupported ONFI version: %d\n", __func__, val);
return 0;
}
@@ -1123,10 +2826,7 @@ static int nand_flash_detect_onfi(struct mtd_info *mtd, struct nand_chip *chip,
if (le16_to_cpu(p->features) & 1)
*busw = NAND_BUSWIDTH_16;
- chip->options &= ~NAND_CHIPOPTIONS_MSK;
- chip->options |= NAND_NO_READRDY & NAND_CHIPOPTIONS_MSK;
-
- pr_info("ONFI flash detected ...\n");
+ pr_info("ONFI flash detected\n");
return 1;
}
@@ -1371,15 +3071,40 @@ static void nand_decode_bbm_options(struct mtd_info *mtd,
chip->bbt_options |= NAND_BBT_SCAN2NDPAGE;
}
+static inline bool is_full_id_nand(struct nand_flash_dev *type)
+{
+ return type->id_len;
+}
+
+static bool find_full_id_nand(struct mtd_info *mtd, struct nand_chip *chip,
+ struct nand_flash_dev *type, u8 *id_data, int *busw)
+{
+ if (!strncmp(type->id, id_data, type->id_len)) {
+ mtd->writesize = type->pagesize;
+ mtd->erasesize = type->erasesize;
+ mtd->oobsize = type->oobsize;
+
+ chip->cellinfo = id_data[2];
+ chip->chipsize = (uint64_t)type->chipsize << 20;
+ chip->options |= type->options;
+
+ *busw = type->options & NAND_BUSWIDTH_16;
+
+ return true;
+ }
+ return false;
+}
+
/*
- * Get the flash and manufacturer id and lookup if the type is supported
+ * Get the flash and manufacturer id and lookup if the type is supported.
*/
static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
struct nand_chip *chip,
- int busw, int *maf_id)
+ int busw,
+ int *maf_id, int *dev_id,
+ struct nand_flash_dev *type)
{
- struct nand_flash_dev *type = NULL;
- int i, dev_id, maf_idx;
+ int i, maf_idx;
u8 id_data[8];
/* Select the device */
@@ -1387,7 +3112,7 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
/*
* Reset the chip, required by some chips (e.g. Micron MT29FxGxxxxx)
- * after power-up
+ * after power-up.
*/
chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
@@ -1396,9 +3121,10 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
/* Read manufacturer and device IDs */
*maf_id = chip->read_byte(mtd);
- dev_id = chip->read_byte(mtd);
+ *dev_id = chip->read_byte(mtd);
- /* Try again to make sure, as some systems the bus-hold or other
+ /*
+ * Try again to make sure, as some systems the bus-hold or other
* interface concerns can cause random data which looks like a
* possibly credible NAND flash to appear. If the two results do
* not match, ignore the device completely.
@@ -1410,19 +3136,24 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
for (i = 0; i < 8; i++)
id_data[i] = chip->read_byte(mtd);
- if (id_data[0] != *maf_id || id_data[1] != dev_id) {
- pr_err("%s: second ID read did not match "
- "%02x,%02x against %02x,%02x\n", __func__,
- *maf_id, dev_id, id_data[0], id_data[1]);
+ if (id_data[0] != *maf_id || id_data[1] != *dev_id) {
+ pr_info("%s: second ID read did not match "
+ "%02x,%02x against %02x,%02x\n", __func__,
+ *maf_id, *dev_id, id_data[0], id_data[1]);
return ERR_PTR(-ENODEV);
}
if (!type)
type = nand_flash_ids;
- for (; type->name != NULL; type++)
- if (dev_id == type->id)
- break;
+ for (; type->name != NULL; type++) {
+ if (is_full_id_nand(type)) {
+ if (find_full_id_nand(mtd, chip, type, id_data, &busw))
+ goto ident_done;
+ } else if (*dev_id == type->dev_id) {
+ break;
+ }
+ }
chip->onfi_version = 0;
if (!type->name || !type->pagesize) {
@@ -1439,7 +3170,10 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
chip->chipsize = (uint64_t)type->chipsize << 20;
- if (!type->pagesize) {
+ if (!type->pagesize && chip->init_size) {
+ /* Set the pagesize, oobsize, erasesize by the driver */
+ busw = chip->init_size(mtd, chip, id_data);
+ } else if (!type->pagesize) {
/* Decode parameters from extended ID */
nand_decode_ext_id(mtd, chip, id_data, &busw);
} else {
@@ -1455,10 +3189,6 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
if (*maf_id != NAND_MFR_SAMSUNG && !type->pagesize)
chip->options &= ~NAND_SAMSUNG_LP_OPTIONS;
ident_done:
- /*
- * Set chip as a default. Board drivers can override it, if necessary
- */
- chip->options |= NAND_NO_AUTOINCR;
/* Try to identify manufacturer */
for (maf_idx = 0; nand_manuf_ids[maf_idx].id != 0x0; maf_idx++) {
@@ -1467,21 +3197,20 @@ ident_done:
}
if (chip->options & NAND_BUSWIDTH_AUTO) {
+ WARN_ON(chip->options & NAND_BUSWIDTH_16);
chip->options |= busw;
nand_set_defaults(chip, busw);
- if (chip->set_buswidth)
- chip->set_buswidth(mtd, chip, busw);
- } else if (busw != (chip->options & NAND_BUSWIDTH_16)) {
+ } else if (busw != (chip->options & NAND_BUSWIDTH_16)) {
/*
* Check, if buswidth is correct. Hardware drivers should set
- * chip correct !
+ * chip correct!
*/
pr_info("NAND device: Manufacturer ID:"
" 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id,
- dev_id, nand_manuf_ids[maf_idx].name, mtd->name);
- pr_warning("NAND bus width %d instead %d bit\n",
- (chip->options & NAND_BUSWIDTH_16) ? 16 : 8,
- busw ? 16 : 8);
+ *dev_id, nand_manuf_ids[maf_idx].name, mtd->name);
+ pr_warn("NAND bus width %d instead %d bit\n",
+ (chip->options & NAND_BUSWIDTH_16) ? 16 : 8,
+ busw ? 16 : 8);
return ERR_PTR(-EINVAL);
}
@@ -1489,7 +3218,7 @@ ident_done:
/* Calculate the address shift from the page size */
chip->page_shift = ffs(mtd->writesize) - 1;
- /* Convert chipsize to number of pages per chip -1. */
+ /* Convert chipsize to number of pages per chip -1 */
chip->pagemask = (chip->chipsize >> chip->page_shift) - 1;
chip->bbt_erase_shift = chip->phys_erase_shift =
@@ -1501,74 +3230,72 @@ ident_done:
chip->chip_shift += 32 - 1;
}
- /* Set the bad block position */
- chip->badblockpos = mtd->writesize > 512 ?
- NAND_LARGE_BADBLOCK_POS : NAND_SMALL_BADBLOCK_POS;
+ chip->badblockbits = 8;
+ chip->erase_cmd = single_erase_cmd;
-#ifdef CONFIG_MTD_WRITE
- /* Check for AND chips with 4 page planes */
- if (chip->options & NAND_4PAGE_ARRAY)
- chip->erase_cmd = multi_erase_cmd;
- else
- chip->erase_cmd = single_erase_cmd;
-#endif
- /* Do not replace user supplied command function ! */
+ /* Do not replace user supplied command function! */
if (mtd->writesize > 512 && chip->cmdfunc == nand_command)
chip->cmdfunc = nand_command_lp;
- pr_notice("Manufacturer ID: 0x%02x, Chip ID: 0x%02x (%s %s),"
- " page size: %d, OOB size: %d\n",
- *maf_id, dev_id, nand_manuf_ids[maf_idx].name,
+ pr_info("NAND device: Manufacturer ID: 0x%02x, Chip ID: 0x%02x (%s %s),"
+ " %dMiB, page size: %d, OOB size: %d\n",
+ *maf_id, *dev_id, nand_manuf_ids[maf_idx].name,
chip->onfi_version ? chip->onfi_params.model : type->name,
- mtd->writesize, mtd->oobsize);
+ (int)(chip->chipsize >> 20), mtd->writesize, mtd->oobsize);
return type;
}
/**
* nand_scan_ident - [NAND Interface] Scan for the NAND device
- * @mtd: MTD device structure
- * @maxchips: Number of chips to scan for
+ * @mtd: MTD device structure
+ * @maxchips: number of chips to scan for
+ * @table: alternative NAND ID table
*
- * This is the first phase of the normal nand_scan() function. It
- * reads the flash ID and sets up MTD fields accordingly.
+ * This is the first phase of the normal nand_scan() function. It reads the
+ * flash ID and sets up MTD fields accordingly.
*
* The mtd->owner field must be set to the module of the caller.
*/
-int nand_scan_ident(struct mtd_info *mtd, int maxchips)
+int nand_scan_ident(struct mtd_info *mtd, int maxchips,
+ struct nand_flash_dev *table)
{
- int i, busw, nand_maf_id;
+ int i, busw, nand_maf_id, nand_dev_id;
struct nand_chip *chip = mtd->priv;
struct nand_flash_dev *type;
- if (chip->options & NAND_BUSWIDTH_AUTO && !chip->set_buswidth) {
- pr_err("buswidth detection but no buswidth callback\n");
- return -EINVAL;
- }
-
/* Get buswidth to select the correct functions */
busw = chip->options & NAND_BUSWIDTH_16;
/* Set the default functions */
nand_set_defaults(chip, busw);
/* Read the flash type */
- type = nand_get_flash_type(mtd, chip, busw, &nand_maf_id);
+ type = nand_get_flash_type(mtd, chip, busw,
+ &nand_maf_id, &nand_dev_id, table);
if (IS_ERR(type)) {
- pr_warning("No NAND device found (%ld)!\n", PTR_ERR(type));
+ if (!(chip->options & NAND_SCAN_SILENT_NODEV))
+ pr_warn("No NAND device found\n");
chip->select_chip(mtd, -1);
return PTR_ERR(type);
}
+ chip->select_chip(mtd, -1);
+
/* Check for a chip array */
for (i = 1; i < maxchips; i++) {
chip->select_chip(mtd, i);
+ /* See comment in nand_get_flash_type for reset */
+ chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
/* Send the command for reading device ID */
chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
/* Read manufacturer and device IDs */
if (nand_maf_id != chip->read_byte(mtd) ||
- type->id != chip->read_byte(mtd))
+ nand_dev_id != chip->read_byte(mtd)) {
+ chip->select_chip(mtd, -1);
break;
+ }
+ chip->select_chip(mtd, -1);
}
if (i > 1)
pr_info("%d NAND chips detected\n", i);
@@ -1579,39 +3306,26 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips)
return 0;
}
+EXPORT_SYMBOL(nand_scan_ident);
-static void __maybe_unused nand_check_hwecc(struct mtd_info *mtd, struct nand_chip *chip)
-{
- if ((!chip->ecc.calculate || !chip->ecc.correct ||
- !chip->ecc.hwctl) &&
- (!chip->ecc.read_page || !chip->ecc.write_page)) {
- pr_warning("No ECC functions supplied, "
- "Hardware ECC not possible\n");
- BUG();
- }
-
- if (mtd->writesize < chip->ecc.size) {
- pr_warning("%d byte HW ECC not possible on "
- "%d byte page size\n",
- chip->ecc.size, mtd->writesize);
- BUG();
- }
-}
/**
* nand_scan_tail - [NAND Interface] Scan for the NAND device
- * @mtd: MTD device structure
- * @maxchips: Number of chips to scan for
+ * @mtd: MTD device structure
*
- * This is the second phase of the normal nand_scan() function. It
- * fills out all the uninitialized function pointers with the defaults
- * and scans for a bad block table if appropriate.
+ * This is the second phase of the normal nand_scan() function. It fills out
+ * all the uninitialized function pointers with the defaults and scans for a
+ * bad block table if appropriate.
*/
int nand_scan_tail(struct mtd_info *mtd)
{
int i;
struct nand_chip *chip = mtd->priv;
+ /* New bad blocks should be marked in OOB, flash-based BBT, or both */
+ BUG_ON((chip->bbt_options & NAND_BBT_NO_OOB_BBM) &&
+ !(chip->bbt_options & NAND_BBT_USE_FLASH));
+
if (!(chip->options & NAND_OWN_BUFFERS))
chip->buffers = kmalloc(sizeof(*chip->buffers), GFP_KERNEL);
if (!chip->buffers)
@@ -1621,9 +3335,9 @@ int nand_scan_tail(struct mtd_info *mtd)
chip->oob_poi = chip->buffers->databuf + mtd->writesize;
/*
- * If no default placement scheme is given, select an appropriate one
+ * If no default placement scheme is given, select an appropriate one.
*/
- if (!chip->ecc.layout) {
+ if (!chip->ecc.layout && (chip->ecc.mode != NAND_ECC_SOFT_BCH)) {
switch (mtd->oobsize) {
case 8:
chip->ecc.layout = &nand_oob_8;
@@ -1634,100 +3348,213 @@ int nand_scan_tail(struct mtd_info *mtd)
case 64:
chip->ecc.layout = &nand_oob_64;
break;
+ case 128:
+ chip->ecc.layout = &nand_oob_128;
+ break;
default:
- pr_warning("No oob scheme defined for "
- "oobsize %d\n", mtd->oobsize);
+ pr_warn("No oob scheme defined for oobsize %d\n",
+ mtd->oobsize);
BUG();
}
}
-#ifdef CONFIG_MTD_WRITE
if (!chip->write_page)
chip->write_page = nand_write_page;
-#endif
+
+ /* set for ONFI nand */
+ if (!chip->onfi_set_features)
+ chip->onfi_set_features = nand_onfi_set_features;
+ if (!chip->onfi_get_features)
+ chip->onfi_get_features = nand_onfi_get_features;
/*
- * check ECC mode, default to software if 3byte/512byte hardware ECC is
+ * Check ECC mode, default to software if 3byte/512byte hardware ECC is
* selected and we have 256 byte pagesize fallback to software ECC
*/
- if (!chip->ecc.read_page_raw)
- chip->ecc.read_page_raw = nand_read_page_raw;
-#ifdef CONFIG_MTD_WRITE
- if (!chip->ecc.write_page_raw)
- chip->ecc.write_page_raw = nand_write_page_raw;
-#endif
+
switch (chip->ecc.mode) {
+#ifdef CONFIG_NAND_ECC_HW_OOB_FIRST
+ case NAND_ECC_HW_OOB_FIRST:
+ /* Similar to NAND_ECC_HW, but a separate read_page handle */
+ if (!chip->ecc.calculate || !chip->ecc.correct ||
+ !chip->ecc.hwctl) {
+ pr_warn("No ECC functions supplied; "
+ "hardware ECC not possible\n");
+ BUG();
+ }
+ if (!chip->ecc.read_page)
+ chip->ecc.read_page = nand_read_page_hwecc_oob_first;
+#endif
#ifdef CONFIG_NAND_ECC_HW
case NAND_ECC_HW:
- nand_check_hwecc(mtd, chip);
- nand_init_ecc_hw(chip);
- break;
+ /* Use standard hwecc read page function? */
+ if (!chip->ecc.read_page)
+ chip->ecc.read_page = nand_read_page_hwecc;
+ if (!chip->ecc.write_page)
+ chip->ecc.write_page = nand_write_page_hwecc;
+ if (!chip->ecc.read_page_raw)
+ chip->ecc.read_page_raw = nand_read_page_raw;
+ if (!chip->ecc.write_page_raw)
+ chip->ecc.write_page_raw = nand_write_page_raw;
+ if (!chip->ecc.read_oob)
+ chip->ecc.read_oob = nand_read_oob_std;
+ if (!chip->ecc.write_oob)
+ chip->ecc.write_oob = nand_write_oob_std;
+ if (!chip->ecc.read_subpage)
+ chip->ecc.read_subpage = nand_read_subpage;
+ if (!chip->ecc.write_subpage)
+ chip->ecc.write_subpage = nand_write_subpage_hwecc;
#endif
#ifdef CONFIG_NAND_ECC_HW_SYNDROME
case NAND_ECC_HW_SYNDROME:
- nand_check_hwecc(mtd, chip);
- nand_init_ecc_hw_syndrome(chip);
- break;
+ if ((!chip->ecc.calculate || !chip->ecc.correct ||
+ !chip->ecc.hwctl) &&
+ (!chip->ecc.read_page ||
+ chip->ecc.read_page == nand_read_page_hwecc ||
+ !chip->ecc.write_page ||
+ chip->ecc.write_page == nand_write_page_hwecc)) {
+ pr_warn("No ECC functions supplied; "
+ "hardware ECC not possible\n");
+ BUG();
+ }
+ /* Use standard syndrome read/write page function? */
+ if (!chip->ecc.read_page)
+ chip->ecc.read_page = nand_read_page_syndrome;
+ if (!chip->ecc.write_page)
+ chip->ecc.write_page = nand_write_page_syndrome;
+ if (!chip->ecc.read_page_raw)
+ chip->ecc.read_page_raw = nand_read_page_raw_syndrome;
+ if (!chip->ecc.write_page_raw)
+ chip->ecc.write_page_raw = nand_write_page_raw_syndrome;
+ if (!chip->ecc.read_oob)
+ chip->ecc.read_oob = nand_read_oob_syndrome;
+ if (!chip->ecc.write_oob)
+ chip->ecc.write_oob = nand_write_oob_syndrome;
+
+ if (mtd->writesize >= chip->ecc.size) {
+ if (!chip->ecc.strength) {
+ pr_warn("Driver must set ecc.strength when using hardware ECC\n");
+ BUG();
+ }
+ break;
+ }
+ pr_warn("%d byte HW ECC not possible on "
+ "%d byte page size, fallback to SW ECC\n",
+ chip->ecc.size, mtd->writesize);
+ chip->ecc.mode = NAND_ECC_SOFT;
#endif
#ifdef CONFIG_NAND_ECC_SOFT
case NAND_ECC_SOFT:
- nand_init_ecc_soft(chip);
+ chip->ecc.calculate = nand_calculate_ecc;
+ chip->ecc.correct = nand_correct_data;
+ chip->ecc.read_page = nand_read_page_swecc;
+ chip->ecc.read_subpage = nand_read_subpage;
+ chip->ecc.write_page = nand_write_page_swecc;
+ chip->ecc.read_page_raw = nand_read_page_raw;
+ chip->ecc.write_page_raw = nand_write_page_raw;
+ chip->ecc.read_oob = nand_read_oob_std;
+ chip->ecc.write_oob = nand_write_oob_std;
+ if (!chip->ecc.size)
+ chip->ecc.size = 256;
+ chip->ecc.bytes = 3;
+ chip->ecc.strength = 1;
+ break;
+#endif
+#ifdef CONFIG_NAND_ECC_BCH
+ case NAND_ECC_SOFT_BCH:
+ if (!mtd_nand_has_bch()) {
+ pr_warn("CONFIG_MTD_ECC_BCH not enabled\n");
+ BUG();
+ }
+ chip->ecc.calculate = nand_bch_calculate_ecc;
+ chip->ecc.correct = nand_bch_correct_data;
+ chip->ecc.read_page = nand_read_page_swecc;
+ chip->ecc.read_subpage = nand_read_subpage;
+ chip->ecc.write_page = nand_write_page_swecc;
+ chip->ecc.read_page_raw = nand_read_page_raw;
+ chip->ecc.write_page_raw = nand_write_page_raw;
+ chip->ecc.read_oob = nand_read_oob_std;
+ chip->ecc.write_oob = nand_write_oob_std;
+ /*
+ * Board driver should supply ecc.size and ecc.bytes values to
+ * select how many bits are correctable; see nand_bch_init()
+ * for details. Otherwise, default to 4 bits for large page
+ * devices.
+ */
+ if (!chip->ecc.size && (mtd->oobsize >= 64)) {
+ chip->ecc.size = 512;
+ chip->ecc.bytes = 7;
+ }
+ chip->ecc.priv = nand_bch_init(mtd,
+ chip->ecc.size,
+ chip->ecc.bytes,
+ &chip->ecc.layout);
+ if (!chip->ecc.priv) {
+ pr_warn("BCH ECC initialization failed!\n");
+ BUG();
+ }
+ chip->ecc.strength =
+ chip->ecc.bytes * 8 / fls(8 * chip->ecc.size);
break;
#endif
#ifdef CONFIG_NAND_ECC_NONE
case NAND_ECC_NONE:
- pr_warning("NAND_ECC_NONE selected by board driver. "
- "This is not recommended !!\n");
+ pr_warn("NAND_ECC_NONE selected by board driver. "
+ "This is not recommended!\n");
chip->ecc.read_page = nand_read_page_raw;
-#ifdef CONFIG_MTD_WRITE
chip->ecc.write_page = nand_write_page_raw;
- chip->ecc.write_oob = nand_write_oob_std;
-#endif
chip->ecc.read_oob = nand_read_oob_std;
+ chip->ecc.read_page_raw = nand_read_page_raw;
+ chip->ecc.write_page_raw = nand_write_page_raw;
+ chip->ecc.write_oob = nand_write_oob_std;
chip->ecc.size = mtd->writesize;
chip->ecc.bytes = 0;
chip->ecc.strength = 0;
break;
#endif
default:
- pr_warning("Invalid NAND_ECC_MODE %d\n",
- chip->ecc.mode);
+ pr_warn("Invalid NAND_ECC_MODE %d\n", chip->ecc.mode);
BUG();
}
+ /* For many systems, the standard OOB write also works for raw */
+ if (!chip->ecc.read_oob_raw)
+ chip->ecc.read_oob_raw = chip->ecc.read_oob;
+ if (!chip->ecc.write_oob_raw)
+ chip->ecc.write_oob_raw = chip->ecc.write_oob;
+
/*
* The number of bytes available for a client to place data into
- * the out of band area
+ * the out of band area.
*/
chip->ecc.layout->oobavail = 0;
- for (i = 0; chip->ecc.layout->oobfree[i].length; i++)
+ for (i = 0; chip->ecc.layout->oobfree[i].length
+ && i < ARRAY_SIZE(chip->ecc.layout->oobfree); i++)
chip->ecc.layout->oobavail +=
chip->ecc.layout->oobfree[i].length;
mtd->oobavail = chip->ecc.layout->oobavail;
/*
* Set the number of read / write steps for one page depending on ECC
- * mode
+ * mode.
*/
chip->ecc.steps = mtd->writesize / chip->ecc.size;
- if(chip->ecc.steps * chip->ecc.size != mtd->writesize) {
- pr_warning("Invalid ecc parameters\n");
+ if (chip->ecc.steps * chip->ecc.size != mtd->writesize) {
+ pr_warn("Invalid ECC parameters\n");
BUG();
}
chip->ecc.total = chip->ecc.steps * chip->ecc.bytes;
- /*
- * Allow subpage writes up to ecc.steps. Not possible for MLC
- * FLASH.
- */
+ /* Allow subpage writes up to ecc.steps. Not possible for MLC flash */
if (!(chip->options & NAND_NO_SUBPAGE_WRITE) &&
!(chip->cellinfo & NAND_CI_CELLTYPE_MSK)) {
- switch(chip->ecc.steps) {
+ switch (chip->ecc.steps) {
case 2:
mtd->subpage_sft = 1;
break;
case 4:
case 8:
+ case 16:
mtd->subpage_sft = 2;
break;
}
@@ -1737,88 +3564,94 @@ int nand_scan_tail(struct mtd_info *mtd)
/* Initialize state */
chip->state = FL_READY;
- /* De-select the device */
- chip->select_chip(mtd, -1);
-
/* Invalidate the pagebuffer reference */
chip->pagebuf = -1;
+ /* Large page NAND with SOFT_ECC should support subpage reads */
+ if ((chip->ecc.mode == NAND_ECC_SOFT) && (chip->page_shift > 9))
+ chip->options |= NAND_SUBPAGE_READ;
+
/* Fill in remaining MTD driver data */
mtd->type = MTD_NANDFLASH;
- mtd->flags = MTD_CAP_NANDFLASH;
-#ifdef CONFIG_MTD_WRITE
+ mtd->flags = (chip->options & NAND_ROM) ? MTD_CAP_ROM :
+ MTD_CAP_NANDFLASH;
mtd->erase = nand_erase;
- mtd->write = nand_write;
- mtd->write_oob = nand_write_oob;
-#endif
mtd->read = nand_read;
-#ifdef CONFIG_NAND_READ_OOB
+ mtd->write = nand_write;
mtd->read_oob = nand_read_oob;
-#endif
+ mtd->write_oob = nand_write_oob;
+ mtd->sync = nand_sync;
mtd->lock = NULL;
mtd->unlock = NULL;
mtd->block_isbad = nand_block_isbad;
-#ifdef CONFIG_MTD_WRITE
mtd->block_markbad = nand_block_markbad;
-#endif
- /* propagate ecc.layout to mtd_info */
+ mtd->writebufsize = mtd->writesize;
+
+ /* propagate ecc info to mtd_info */
mtd->ecclayout = chip->ecc.layout;
mtd->ecc_strength = chip->ecc.strength;
+ /*
+ * Initialize bitflip_threshold to its default prior scan_bbt() call.
+ * scan_bbt() might invoke mtd_read(), thus bitflip_threshold must be
+ * properly set.
+ */
+ if (!mtd->bitflip_threshold)
+ mtd->bitflip_threshold = mtd->ecc_strength;
/* Check, if we should skip the bad block table scan */
if (chip->options & NAND_SKIP_BBTSCAN)
return 0;
-#ifdef CONFIG_NAND_BBT
+
/* Build bad block table */
return chip->scan_bbt(mtd);
-#else
- return 0;
-#endif
}
+EXPORT_SYMBOL(nand_scan_tail);
/**
* nand_scan - [NAND Interface] Scan for the NAND device
- * @mtd: MTD device structure
- * @maxchips: Number of chips to scan for
- *
- * This fills out all the uninitialized function pointers
- * with the defaults.
- * The flash ID is read and the mtd/chip structures are
- * filled with the appropriate values.
- * The mtd->owner field must be set to the module of the caller
+ * @mtd: MTD device structure
+ * @maxchips: number of chips to scan for
*
+ * This fills out all the uninitialized function pointers with the defaults.
+ * The flash ID is read and the mtd/chip structures are filled with the
+ * appropriate values. The mtd->owner field must be set to the module of the
+ * caller.
*/
int nand_scan(struct mtd_info *mtd, int maxchips)
{
int ret;
- ret = nand_scan_ident(mtd, maxchips);
+ ret = nand_scan_ident(mtd, maxchips, NULL);
if (!ret)
ret = nand_scan_tail(mtd);
return ret;
}
+EXPORT_SYMBOL(nand_scan);
/**
* nand_release - [NAND Interface] Free resources held by the NAND device
- * @mtd: MTD device structure
-*/
+ * @mtd: MTD device structure
+ */
void nand_release(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
- /* Deregister the device */
+ if (chip->ecc.mode == NAND_ECC_SOFT_BCH)
+ nand_bch_free((struct nand_bch_control *)chip->ecc.priv);
+
del_mtd_device(mtd);
/* Free bad block table memory */
kfree(chip->bbt);
if (!(chip->options & NAND_OWN_BUFFERS))
kfree(chip->buffers);
-}
-EXPORT_SYMBOL(nand_scan);
-EXPORT_SYMBOL(nand_scan_ident);
-EXPORT_SYMBOL(nand_scan_tail);
-EXPORT_SYMBOL(nand_release);
+ /* Free bad block descriptor memory */
+ if (chip->badblock_pattern && chip->badblock_pattern->options
+ & NAND_BBT_DYNAMICSTRUCT)
+ kfree(chip->badblock_pattern);
+}
+EXPORT_SYMBOL_GPL(nand_release);
static int mtd_set_erasebad(struct param_d *param, void *priv)
{
@@ -1871,5 +3704,3 @@ int add_mtd_nand_device(struct mtd_info *mtd, char *devname)
return ret;
}
-
-#endif /* DOXYGEN_SHOULD_SKIP_THIS */
diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/nand_bbt.c
index e598ca6..11f7a8b 100644
--- a/drivers/mtd/nand/nand_bbt.c
+++ b/drivers/mtd/nand/nand_bbt.c
@@ -4,9 +4,7 @@
* Overview:
* Bad block table support for the NAND driver
*
- * Copyright (C) 2004 Thomas Gleixner (tglx@linutronix.de)
- *
- * $Id: nand_bbt.c,v 1.36 2005/11/07 11:14:30 gleixner Exp $
+ * Copyright © 2004 Thomas Gleixner (tglx@linutronix.de)
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -15,28 +13,37 @@
* Description:
*
* When nand_scan_bbt is called, then it tries to find the bad block table
- * depending on the options in the bbt descriptor(s). If a bbt is found
- * then the contents are read and the memory based bbt is created. If a
- * mirrored bbt is selected then the mirror is searched too and the
- * versions are compared. If the mirror has a greater version number
- * than the mirror bbt is used to build the memory based bbt.
+ * depending on the options in the BBT descriptor(s). If no flash based BBT
+ * (NAND_BBT_USE_FLASH) is specified then the device is scanned for factory
+ * marked good / bad blocks. This information is used to create a memory BBT.
+ * Once a new bad block is discovered then the "factory" information is updated
+ * on the device.
+ * If a flash based BBT is specified then the function first tries to find the
+ * BBT on flash. If a BBT is found then the contents are read and the memory
+ * based BBT is created. If a mirrored BBT is selected then the mirror is
+ * searched too and the versions are compared. If the mirror has a greater
+ * version number, then the mirror BBT is used to build the memory based BBT.
* If the tables are not versioned, then we "or" the bad block information.
- * If one of the bbt's is out of date or does not exist it is (re)created.
- * If no bbt exists at all then the device is scanned for factory marked
+ * If one of the BBTs is out of date or does not exist it is (re)created.
+ * If no BBT exists at all then the device is scanned for factory marked
* good / bad blocks and the bad block tables are created.
*
- * For manufacturer created bbts like the one found on M-SYS DOC devices
- * the bbt is searched and read but never created
+ * For manufacturer created BBTs like the one found on M-SYS DOC devices
+ * the BBT is searched and read but never created
*
- * The autogenerated bad block table is located in the last good blocks
+ * The auto generated bad block table is located in the last good blocks
* of the device. The table is mirrored, so it can be updated eventually.
- * The table is marked in the oob area with an ident pattern and a version
- * number which indicates which of both tables is more up to date.
+ * The table is marked in the OOB area with an ident pattern and a version
+ * number which indicates which of both tables is more up to date. If the NAND
+ * controller needs the complete OOB area for the ECC information then the
+ * option NAND_BBT_NO_OOB should be used (along with NAND_BBT_USE_FLASH, of
+ * course): it moves the ident pattern and the version byte into the data area
+ * and the OOB area will remain untouched.
*
* The table uses 2 bits per block
- * 11b: block is good
- * 00b: block is factory marked bad
- * 01b, 10b: block is marked bad due to wear
+ * 11b: block is good
+ * 00b: block is factory marked bad
+ * 01b, 10b: block is marked bad due to wear
*
* The memory bad block table uses the following scheme:
* 00b: block is good
@@ -52,8 +59,6 @@
*
*/
-#define pr_fmt(fmt) "nand: " fmt
-
#include <common.h>
#include <linux/types.h>
#include <linux/mtd/mtd.h>
@@ -64,109 +69,139 @@
#include <errno.h>
#include <malloc.h>
-#ifndef DOXYGEN_SHOULD_SKIP_THIS
+static int check_pattern_no_oob(uint8_t *buf, struct nand_bbt_descr *td)
+{
+ if (memcmp(buf, td->pattern, td->len))
+ return -1;
+ return 0;
+}
/**
* check_pattern - [GENERIC] check if a pattern is in the buffer
- * @buf: the buffer to search
- * @len: the length of buffer to search
- * @paglen: the pagelength
- * @td: search pattern descriptor
- *
- * Check for a pattern at the given place. Used to search bad block
- * tables and good / bad block identifiers.
- * If the SCAN_EMPTY option is set then check, if all bytes except the
- * pattern area contain 0xff
+ * @buf: the buffer to search
+ * @len: the length of buffer to search
+ * @paglen: the pagelength
+ * @td: search pattern descriptor
*
-*/
+ * Check for a pattern at the given place. Used to search bad block tables and
+ * good / bad block identifiers. If the SCAN_EMPTY option is set then check, if
+ * all bytes except the pattern area contain 0xff.
+ */
static int check_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_descr *td)
{
- int i, end = 0;
+ int end = 0;
uint8_t *p = buf;
+ if (td->options & NAND_BBT_NO_OOB)
+ return check_pattern_no_oob(buf, td);
+
end = paglen + td->offs;
- if (td->options & NAND_BBT_SCANEMPTY) {
- for (i = 0; i < end; i++) {
- if (p[i] != 0xff)
- return -1;
- }
- }
+ if (td->options & NAND_BBT_SCANEMPTY)
+ if (memchr_inv(p, 0xff, end))
+ return -1;
p += end;
/* Compare the pattern */
- for (i = 0; i < td->len; i++) {
- if (p[i] != td->pattern[i])
- return -1;
- }
+ if (memcmp(p, td->pattern, td->len))
+ return -1;
if (td->options & NAND_BBT_SCANEMPTY) {
p += td->len;
end += td->len;
- for (i = end; i < len; i++) {
- if (*p++ != 0xff)
- return -1;
- }
+ if (memchr_inv(p, 0xff, len - end))
+ return -1;
}
return 0;
}
/**
* check_short_pattern - [GENERIC] check if a pattern is in the buffer
- * @buf: the buffer to search
- * @td: search pattern descriptor
- *
- * Check for a pattern at the given place. Used to search bad block
- * tables and good / bad block identifiers. Same as check_pattern, but
- * no optional empty check
+ * @buf: the buffer to search
+ * @td: search pattern descriptor
*
-*/
+ * Check for a pattern at the given place. Used to search bad block tables and
+ * good / bad block identifiers. Same as check_pattern, but no optional empty
+ * check.
+ */
static int check_short_pattern(uint8_t *buf, struct nand_bbt_descr *td)
{
- int i;
- uint8_t *p = buf;
-
/* Compare the pattern */
- for (i = 0; i < td->len; i++) {
- if (p[td->offs + i] != td->pattern[i])
- return -1;
- }
+ if (memcmp(buf + td->offs, td->pattern, td->len))
+ return -1;
return 0;
}
/**
+ * add_marker_len - compute the length of the marker in data area
+ * @td: BBT descriptor used for computation
+ *
+ * The length will be 0 if the marker is located in OOB area.
+ */
+static u32 add_marker_len(struct nand_bbt_descr *td)
+{
+ u32 len;
+
+ if (!(td->options & NAND_BBT_NO_OOB))
+ return 0;
+
+ len = td->len;
+ if (td->options & NAND_BBT_VERSION)
+ len++;
+ return len;
+}
+
+/**
* read_bbt - [GENERIC] Read the bad block table starting from page
- * @mtd: MTD device structure
- * @buf: temporary buffer
- * @page: the starting page
- * @num: the number of bbt descriptors to read
- * @bits: number of bits per block
- * @offs: offset in the memory table
- * @reserved_block_code: Pattern to identify reserved blocks
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @page: the starting page
+ * @num: the number of bbt descriptors to read
+ * @td: the bbt describtion table
+ * @offs: offset in the memory table
*
* Read the bad block table starting from page.
- *
*/
static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num,
- int bits, int offs, int reserved_block_code)
+ struct nand_bbt_descr *td, int offs)
{
- int res, i, j, act = 0;
+ int res, ret = 0, i, j, act = 0;
struct nand_chip *this = mtd->priv;
size_t retlen, len, totlen;
loff_t from;
- uint8_t msk = (uint8_t) ((1 << bits) - 1);
+ int bits = td->options & NAND_BBT_NRBITS_MSK;
+ uint8_t msk = (uint8_t)((1 << bits) - 1);
+ u32 marker_len;
+ int reserved_block_code = td->reserved_block_code;
totlen = (num * bits) >> 3;
- from = ((loff_t) page) << this->page_shift;
+ marker_len = add_marker_len(td);
+ from = ((loff_t)page) << this->page_shift;
while (totlen) {
- len = min(totlen, (size_t) (1 << this->bbt_erase_shift));
+ len = min(totlen, (size_t)(1 << this->bbt_erase_shift));
+ if (marker_len) {
+ /*
+ * In case the BBT marker is not in the OOB area it
+ * will be just in the first page.
+ */
+ len -= marker_len;
+ from += marker_len;
+ marker_len = 0;
+ }
res = mtd_read(mtd, from, len, &retlen, buf);
if (res < 0) {
- if (retlen != len) {
- pr_info("nand_bbt: Error reading bad block table\n");
+ if (mtd_is_eccerr(res)) {
+ pr_info("nand_bbt: ECC error in BBT at "
+ "0x%012llx\n", from & ~mtd->writesize);
+ return res;
+ } else if (mtd_is_bitflip(res)) {
+ pr_info("nand_bbt: corrected error in BBT at "
+ "0x%012llx\n", from & ~mtd->writesize);
+ ret = res;
+ } else {
+ pr_info("nand_bbt: error reading BBT\n");
return res;
}
- pr_warning("nand_bbt: ECC error while reading bad block table\n");
}
/* Analyse data */
@@ -177,17 +212,19 @@ static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num,
if (tmp == msk)
continue;
if (reserved_block_code && (tmp == reserved_block_code)) {
- pr_debug("nand_read_bbt: Reserved block at 0x%08x\n",
- ((offs << 2) + (act >> 1)) << this->bbt_erase_shift);
+ pr_info("nand_read_bbt: reserved block at 0x%012llx\n",
+ (loff_t)((offs << 2) + (act >> 1)) << this->bbt_erase_shift);
this->bbt[offs + (act >> 3)] |= 0x2 << (act & 0x06);
mtd->ecc_stats.bbtblocks++;
continue;
}
- /* Leave it for now, if its matured we can move this
- * message to MTD_DEBUG_LEVEL0 */
- pr_debug("nand_read_bbt: Bad block at 0x%08x\n",
- ((offs << 2) + (act >> 1)) << this->bbt_erase_shift);
- /* Factory marked bad or worn out ? */
+ /*
+ * Leave it for now, if it's matured we can
+ * move this message to pr_debug.
+ */
+ pr_info("nand_read_bbt: bad block at 0x%012llx\n",
+ (loff_t)((offs << 2) + (act >> 1)) << this->bbt_erase_shift);
+ /* Factory marked bad or worn out? */
if (tmp == 0)
this->bbt[offs + (act >> 3)] |= 0x3 << (act & 0x06);
else
@@ -198,66 +235,110 @@ static int read_bbt(struct mtd_info *mtd, uint8_t *buf, int page, int num,
totlen -= len;
from += len;
}
- return 0;
+ return ret;
}
/**
* read_abs_bbt - [GENERIC] Read the bad block table starting at a given page
- * @mtd: MTD device structure
- * @buf: temporary buffer
- * @td: descriptor for the bad block table
- * @chip: read the table for a specific chip, -1 read all chips.
- * Applies only if NAND_BBT_PERCHIP option is set
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
+ * @chip: read the table for a specific chip, -1 read all chips; applies only if
+ * NAND_BBT_PERCHIP option is set
*
- * Read the bad block table for all chips starting at a given page
- * We assume that the bbt bits are in consecutive order.
-*/
+ * Read the bad block table for all chips starting at a given page. We assume
+ * that the bbt bits are in consecutive order.
+ */
static int read_abs_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td, int chip)
{
struct nand_chip *this = mtd->priv;
int res = 0, i;
- int bits;
- bits = td->options & NAND_BBT_NRBITS_MSK;
if (td->options & NAND_BBT_PERCHIP) {
int offs = 0;
for (i = 0; i < this->numchips; i++) {
if (chip == -1 || chip == i)
- res = read_bbt (mtd, buf, td->pages[i], this->chipsize >> this->bbt_erase_shift, bits, offs, td->reserved_block_code);
+ res = read_bbt(mtd, buf, td->pages[i],
+ this->chipsize >> this->bbt_erase_shift,
+ td, offs);
if (res)
return res;
offs += this->chipsize >> (this->bbt_erase_shift + 2);
}
} else {
- res = read_bbt (mtd, buf, td->pages[0], mtd->size >> this->bbt_erase_shift, bits, 0, td->reserved_block_code);
+ res = read_bbt(mtd, buf, td->pages[0],
+ mtd->size >> this->bbt_erase_shift, td, 0);
if (res)
return res;
}
return 0;
}
-/*
- * Scan read raw data from flash
+/* BBT marker is in the first page, no OOB */
+static int scan_read_data(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
+ struct nand_bbt_descr *td)
+{
+ size_t retlen;
+ size_t len;
+
+ len = td->len;
+ if (td->options & NAND_BBT_VERSION)
+ len++;
+
+ return mtd_read(mtd, offs, len, &retlen, buf);
+}
+
+/**
+ * scan_read_oob - [GENERIC] Scan data+OOB region to buffer
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @offs: offset at which to scan
+ * @len: length of data region to read
+ *
+ * Scan read data from data+OOB. May traverse multiple pages, interleaving
+ * page,OOB,page,OOB,... in buf. Completes transfer and returns the "strongest"
+ * ECC condition (error or bitflip). May quit on the first (non-ECC) error.
*/
-static int scan_read_raw(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
+static int scan_read_oob(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
size_t len)
{
struct mtd_oob_ops ops;
+ int res, ret = 0;
- ops.mode = MTD_OPS_RAW;
+ ops.mode = MTD_OPS_PLACE_OOB;
ops.ooboffs = 0;
ops.ooblen = mtd->oobsize;
- ops.oobbuf = buf;
- ops.datbuf = buf;
- ops.len = len;
- return mtd->read_oob(mtd, offs, &ops);
+ while (len > 0) {
+ ops.datbuf = buf;
+ ops.len = min(len, (size_t)mtd->writesize);
+ ops.oobbuf = buf + ops.len;
+
+ res = mtd_read_oob(mtd, offs, &ops);
+ if (res) {
+ if (!mtd_is_bitflip_or_eccerr(res))
+ return res;
+ else if (mtd_is_eccerr(res) || !ret)
+ ret = res;
+ }
+
+ buf += mtd->oobsize + mtd->writesize;
+ len -= mtd->writesize;
+ offs += mtd->writesize;
+ }
+ return ret;
}
-/*
- * Scan write data with oob to flash
- */
-#ifdef CONFIG_MTD_WRITE
+static int scan_read(struct mtd_info *mtd, uint8_t *buf, loff_t offs,
+ size_t len, struct nand_bbt_descr *td)
+{
+ if (td->options & NAND_BBT_NO_OOB)
+ return scan_read_data(mtd, buf, offs, td);
+ else
+ return scan_read_oob(mtd, buf, offs, len);
+}
+
+/* Scan write data with oob to flash */
static int scan_write_bbt(struct mtd_info *mtd, loff_t offs, size_t len,
uint8_t *buf, uint8_t *oob)
{
@@ -270,71 +351,74 @@ static int scan_write_bbt(struct mtd_info *mtd, loff_t offs, size_t len,
ops.oobbuf = oob;
ops.len = len;
- return mtd->write_oob(mtd, offs, &ops);
+ return mtd_write_oob(mtd, offs, &ops);
+}
+
+static u32 bbt_get_ver_offs(struct mtd_info *mtd, struct nand_bbt_descr *td)
+{
+ u32 ver_offs = td->veroffs;
+
+ if (!(td->options & NAND_BBT_NO_OOB))
+ ver_offs += mtd->writesize;
+ return ver_offs;
}
-#endif
/**
* read_abs_bbts - [GENERIC] Read the bad block table(s) for all chips starting at a given page
- * @mtd: MTD device structure
- * @buf: temporary buffer
- * @td: descriptor for the bad block table
- * @md: descriptor for the bad block table mirror
- *
- * Read the bad block table(s) for all chips starting at a given page
- * We assume that the bbt bits are in consecutive order.
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
+ * @md: descriptor for the bad block table mirror
*
-*/
-static int read_abs_bbts(struct mtd_info *mtd, uint8_t *buf,
- struct nand_bbt_descr *td, struct nand_bbt_descr *md)
+ * Read the bad block table(s) for all chips starting at a given page. We
+ * assume that the bbt bits are in consecutive order.
+ */
+static void read_abs_bbts(struct mtd_info *mtd, uint8_t *buf,
+ struct nand_bbt_descr *td, struct nand_bbt_descr *md)
{
struct nand_chip *this = mtd->priv;
/* Read the primary version, if available */
if (td->options & NAND_BBT_VERSION) {
- scan_read_raw(mtd, buf, td->pages[0] << this->page_shift,
- mtd->writesize);
- td->version[0] = buf[mtd->writesize + td->veroffs];
- pr_debug("Bad block table at page %d, version 0x%02X\n",
- td->pages[0], td->version[0]);
+ scan_read(mtd, buf, (loff_t)td->pages[0] << this->page_shift,
+ mtd->writesize, td);
+ td->version[0] = buf[bbt_get_ver_offs(mtd, td)];
+ pr_info("Bad block table at page %d, version 0x%02X\n",
+ td->pages[0], td->version[0]);
}
/* Read the mirror version, if available */
if (md && (md->options & NAND_BBT_VERSION)) {
- scan_read_raw(mtd, buf, md->pages[0] << this->page_shift,
- mtd->writesize);
- md->version[0] = buf[mtd->writesize + md->veroffs];
- pr_debug("Bad block table at page %d, version 0x%02X\n",
- md->pages[0], md->version[0]);
+ scan_read(mtd, buf, (loff_t)md->pages[0] << this->page_shift,
+ mtd->writesize, md);
+ md->version[0] = buf[bbt_get_ver_offs(mtd, md)];
+ pr_info("Bad block table at page %d, version 0x%02X\n",
+ md->pages[0], md->version[0]);
}
- return 1;
}
-/*
- * Scan a given block full
- */
+/* Scan a given block full */
static int scan_block_full(struct mtd_info *mtd, struct nand_bbt_descr *bd,
loff_t offs, uint8_t *buf, size_t readlen,
- int scanlen, int len)
+ int scanlen, int numpages)
{
int ret, j;
- ret = scan_read_raw(mtd, buf, offs, readlen);
- if (ret)
+ ret = scan_read_oob(mtd, buf, offs, readlen);
+ /* Ignore ECC errors when checking for BBM */
+ if (ret && !mtd_is_bitflip_or_eccerr(ret))
return ret;
- for (j = 0; j < len; j++, buf += scanlen) {
+ for (j = 0; j < numpages; j++, buf += scanlen) {
if (check_pattern(buf, scanlen, mtd->writesize, bd))
return 1;
}
return 0;
}
-/*
- * Scan a given block partially
- */
+/* Scan a given block partially */
static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd,
- loff_t offs, uint8_t *buf, int len)
+ loff_t offs, uint8_t *buf, int numpages)
{
struct mtd_oob_ops ops;
int j, ret;
@@ -345,14 +429,14 @@ static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd,
ops.datbuf = NULL;
ops.mode = MTD_OPS_PLACE_OOB;
- for (j = 0; j < len; j++) {
+ for (j = 0; j < numpages; j++) {
/*
- * Read the full oob until read_oob is fixed to
- * handle single byte reads for 16 bit
- * buswidth
+ * Read the full oob until read_oob is fixed to handle single
+ * byte reads for 16 bit buswidth.
*/
- ret = mtd->read_oob(mtd, offs, &ops);
- if (ret)
+ ret = mtd_read_oob(mtd, offs, &ops);
+ /* Ignore ECC errors when checking for BBM */
+ if (ret && !mtd_is_bitflip_or_eccerr(ret))
return ret;
if (check_short_pattern(buf, bd))
@@ -365,20 +449,20 @@ static int scan_block_fast(struct mtd_info *mtd, struct nand_bbt_descr *bd,
/**
* create_bbt - [GENERIC] Create a bad block table by scanning the device
- * @mtd: MTD device structure
- * @buf: temporary buffer
- * @bd: descriptor for the good/bad block search pattern
- * @chip: create the table for a specific chip, -1 read all chips.
- * Applies only if NAND_BBT_PERCHIP option is set
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @bd: descriptor for the good/bad block search pattern
+ * @chip: create the table for a specific chip, -1 read all chips; applies only
+ * if NAND_BBT_PERCHIP option is set
*
- * Create a bad block table by scanning the device
- * for the given good/bad block identify pattern
+ * Create a bad block table by scanning the device for the given good/bad block
+ * identify pattern.
*/
static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
struct nand_bbt_descr *bd, int chip)
{
struct nand_chip *this = mtd->priv;
- int i, numblocks, len, scanlen;
+ int i, numblocks, numpages, scanlen;
int startblock;
loff_t from;
size_t readlen;
@@ -386,13 +470,11 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
pr_info("Scanning device for bad blocks\n");
if (bd->options & NAND_BBT_SCANALLPAGES)
- len = 1 << (this->bbt_erase_shift - this->page_shift);
- else {
- if (bd->options & NAND_BBT_SCAN2NDPAGE)
- len = 2;
- else
- len = 1;
- }
+ numpages = 1 << (this->bbt_erase_shift - this->page_shift);
+ else if (bd->options & NAND_BBT_SCAN2NDPAGE)
+ numpages = 2;
+ else
+ numpages = 1;
if (!(bd->options & NAND_BBT_SCANEMPTY)) {
/* We need only read few bytes from the OOB area */
@@ -401,43 +483,50 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
} else {
/* Full page content should be read */
scanlen = mtd->writesize + mtd->oobsize;
- readlen = len * mtd->writesize;
+ readlen = numpages * mtd->writesize;
}
if (chip == -1) {
- /* Note that numblocks is 2 * (real numblocks) here, see i+=2
- * below as it makes shifting and masking less painful */
+ /*
+ * Note that numblocks is 2 * (real numblocks) here, see i+=2
+ * below as it makes shifting and masking less painful
+ */
numblocks = mtd->size >> (this->bbt_erase_shift - 1);
startblock = 0;
from = 0;
} else {
if (chip >= this->numchips) {
- pr_warning("create_bbt(): chipnr (%d) > available chips (%d)\n",
+ pr_warn("create_bbt(): chipnr (%d) > available chips (%d)\n",
chip + 1, this->numchips);
return -EINVAL;
}
numblocks = this->chipsize >> (this->bbt_erase_shift - 1);
startblock = chip * numblocks;
numblocks += startblock;
- from = startblock << (this->bbt_erase_shift - 1);
+ from = (loff_t)startblock << (this->bbt_erase_shift - 1);
}
+ if (this->bbt_options & NAND_BBT_SCANLASTPAGE)
+ from += mtd->erasesize - (mtd->writesize * numpages);
+
for (i = startblock; i < numblocks;) {
int ret;
+ BUG_ON(bd->options & NAND_BBT_NO_OOB);
+
if (bd->options & NAND_BBT_SCANALLPAGES)
ret = scan_block_full(mtd, bd, from, buf, readlen,
- scanlen, len);
+ scanlen, numpages);
else
- ret = scan_block_fast(mtd, bd, from, buf, len);
+ ret = scan_block_fast(mtd, bd, from, buf, numpages);
if (ret < 0)
return ret;
if (ret) {
this->bbt[i >> 3] |= 0x03 << (i & 0x6);
- pr_warning("Bad eraseblock %d at 0x%08x\n",
- i >> 1, (unsigned int)from);
+ pr_warn("Bad eraseblock %d at 0x%012llx\n",
+ i >> 1, (unsigned long long)from);
mtd->ecc_stats.badblocks++;
}
@@ -449,20 +538,18 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
/**
* search_bbt - [GENERIC] scan the device for a specific bad block table
- * @mtd: MTD device structure
- * @buf: temporary buffer
- * @td: descriptor for the bad block table
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
*
- * Read the bad block table by searching for a given ident pattern.
- * Search is preformed either from the beginning up or from the end of
- * the device downwards. The search starts always at the start of a
- * block.
- * If the option NAND_BBT_PERCHIP is given, each chip is searched
- * for a bbt, which contains the bad block information of this chip.
- * This is necessary to provide support for certain DOC devices.
+ * Read the bad block table by searching for a given ident pattern. Search is
+ * preformed either from the beginning up or from the end of the device
+ * downwards. The search starts always at the start of a block. If the option
+ * NAND_BBT_PERCHIP is given, each chip is searched for a bbt, which contains
+ * the bad block information of this chip. This is necessary to provide support
+ * for certain DOC devices.
*
- * The bbt ident pattern resides in the oob area of the first page
- * in a block.
+ * The bbt ident pattern resides in the oob area of the first page in a block.
*/
static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *td)
{
@@ -473,7 +560,7 @@ static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr
int bbtblocks;
int blocktopage = this->bbt_erase_shift - this->page_shift;
- /* Search direction top -> down ? */
+ /* Search direction top -> down? */
if (td->options & NAND_BBT_LASTBLOCK) {
startblock = (mtd->size >> this->bbt_erase_shift) - 1;
dir = -1;
@@ -482,7 +569,7 @@ static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr
dir = 1;
}
- /* Do we have a bbt per chip ? */
+ /* Do we have a bbt per chip? */
if (td->options & NAND_BBT_PERCHIP) {
chips = this->numchips;
bbtblocks = this->chipsize >> this->bbt_erase_shift;
@@ -503,14 +590,15 @@ static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr
for (block = 0; block < td->maxblocks; block++) {
int actblock = startblock + dir * block;
- loff_t offs = actblock << this->bbt_erase_shift;
+ loff_t offs = (loff_t)actblock << this->bbt_erase_shift;
/* Read first page */
- scan_read_raw(mtd, buf, offs, mtd->writesize);
+ scan_read(mtd, buf, offs, mtd->writesize, td);
if (!check_pattern(buf, scanlen, mtd->writesize, td)) {
td->pages[i] = actblock << blocktopage;
if (td->options & NAND_BBT_VERSION) {
- td->version[i] = buf[mtd->writesize + td->veroffs];
+ offs = bbt_get_ver_offs(mtd, td);
+ td->version[i] = buf[offs];
}
break;
}
@@ -520,24 +608,26 @@ static int search_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr
/* Check, if we found a bbt for each requested chip */
for (i = 0; i < chips; i++) {
if (td->pages[i] == -1)
- pr_warning("Bad block table not found for chip %d\n", i);
+ pr_warn("Bad block table not found for chip %d\n", i);
else
- pr_debug("Bad block table found at page %d, version 0x%02X\n", td->pages[i],
- td->version[i]);
+ pr_info("Bad block table found at page %d, version "
+ "0x%02X\n", td->pages[i], td->version[i]);
}
return 0;
}
/**
* search_read_bbts - [GENERIC] scan the device for bad block table(s)
- * @mtd: MTD device structure
- * @buf: temporary buffer
- * @td: descriptor for the bad block table
- * @md: descriptor for the bad block table mirror
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
+ * @md: descriptor for the bad block table mirror
*
- * Search and read the bad block table(s)
-*/
-static int search_read_bbts(struct mtd_info *mtd, uint8_t * buf, struct nand_bbt_descr *td, struct nand_bbt_descr *md)
+ * Search and read the bad block table(s).
+ */
+static void search_read_bbts(struct mtd_info *mtd, uint8_t *buf,
+ struct nand_bbt_descr *td,
+ struct nand_bbt_descr *md)
{
/* Search the primary table */
search_bbt(mtd, buf, td);
@@ -545,24 +635,18 @@ static int search_read_bbts(struct mtd_info *mtd, uint8_t * buf, struct nand_bbt
/* Search the mirror table */
if (md)
search_bbt(mtd, buf, md);
-
- /* Force result check */
- return 1;
}
/**
* write_bbt - [GENERIC] (Re)write the bad block table
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @td: descriptor for the bad block table
+ * @md: descriptor for the bad block table mirror
+ * @chipsel: selector for a specific chip, -1 for all
*
- * @mtd: MTD device structure
- * @buf: temporary buffer
- * @td: descriptor for the bad block table
- * @md: descriptor for the bad block table mirror
- * @chipsel: selector for a specific chip, -1 for all
- *
- * (Re)write the bad block table
- *
-*/
-#ifdef CONFIG_MTD_WRITE
+ * (Re)write the bad block table.
+ */
static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
struct nand_bbt_descr *td, struct nand_bbt_descr *md,
int chipsel)
@@ -585,10 +669,10 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
if (!rcode)
rcode = 0xff;
- /* Write bad block table per chip rather than per device ? */
+ /* Write bad block table per chip rather than per device? */
if (td->options & NAND_BBT_PERCHIP) {
numblocks = (int)(this->chipsize >> this->bbt_erase_shift);
- /* Full device write or specific chip ? */
+ /* Full device write or specific chip? */
if (chipsel == -1) {
nrchips = this->numchips;
} else {
@@ -602,8 +686,8 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
/* Loop through the chips */
for (; chip < nrchips; chip++) {
-
- /* There was already a version of the table, reuse the page
+ /*
+ * There was already a version of the table, reuse the page
* This applies for absolute placement too, as we have the
* page nr. in td->pages.
*/
@@ -612,8 +696,10 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
goto write;
}
- /* Automatic placement of the bad block table */
- /* Search direction top -> down ? */
+ /*
+ * Automatic placement of the bad block table. Search direction
+ * top -> down?
+ */
if (td->options & NAND_BBT_LASTBLOCK) {
startblock = numblocks * (chip + 1) - 1;
dir = -1;
@@ -662,29 +748,27 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
bbtoffs = chip * (numblocks >> 2);
- to = ((loff_t) page) << this->page_shift;
+ to = ((loff_t)page) << this->page_shift;
- /* Must we save the block contents ? */
+ /* Must we save the block contents? */
if (td->options & NAND_BBT_SAVECONTENT) {
/* Make it block aligned */
- to &= ~((loff_t) ((1 << this->bbt_erase_shift) - 1));
+ to &= ~((loff_t)((1 << this->bbt_erase_shift) - 1));
len = 1 << this->bbt_erase_shift;
res = mtd_read(mtd, to, len, &retlen, buf);
if (res < 0) {
if (retlen != len) {
- pr_info("nand_bbt: Error "
- "reading block for writing "
- "the bad block table\n");
+ pr_info("nand_bbt: error reading block "
+ "for writing the bad block table\n");
return res;
}
- pr_warning("nand_bbt: ECC error "
- "while reading block for writing "
- "bad block table\n");
+ pr_warn("nand_bbt: ECC error while reading "
+ "block for writing bad block table\n");
}
/* Read oob data */
ops.ooblen = (len >> this->page_shift) * mtd->oobsize;
ops.oobbuf = &buf[len];
- res = mtd->read_oob(mtd, to + mtd->writesize, &ops);
+ res = mtd_read_oob(mtd, to + mtd->writesize, &ops);
if (res < 0 || ops.oobretlen != ops.ooblen)
goto outerr;
@@ -692,15 +776,29 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
pageoffs = page - (int)(to >> this->page_shift);
offs = pageoffs << this->page_shift;
/* Preset the bbt area with 0xff */
- memset(&buf[offs], 0xff, (size_t) (numblocks >> sft));
+ memset(&buf[offs], 0xff, (size_t)(numblocks >> sft));
ooboffs = len + (pageoffs * mtd->oobsize);
+ } else if (td->options & NAND_BBT_NO_OOB) {
+ ooboffs = 0;
+ offs = td->len;
+ /* The version byte */
+ if (td->options & NAND_BBT_VERSION)
+ offs++;
+ /* Calc length */
+ len = (size_t)(numblocks >> sft);
+ len += offs;
+ /* Make it page aligned! */
+ len = ALIGN(len, mtd->writesize);
+ /* Preset the buffer with 0xff */
+ memset(buf, 0xff, len);
+ /* Pattern is located at the begin of first page */
+ memcpy(buf, td->pattern, td->len);
} else {
/* Calc length */
- len = (size_t) (numblocks >> sft);
- /* Make it page aligned ! */
- len = (len + (mtd->writesize - 1)) &
- ~(mtd->writesize - 1);
+ len = (size_t)(numblocks >> sft);
+ /* Make it page aligned! */
+ len = ALIGN(len, mtd->writesize);
/* Preset the buffer with 0xff */
memset(buf, 0xff, len +
(len >> this->page_shift)* mtd->oobsize);
@@ -713,13 +811,13 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
if (td->options & NAND_BBT_VERSION)
buf[ooboffs + td->veroffs] = td->version[chip];
- /* walk through the memory table */
+ /* Walk through the memory table */
for (i = 0; i < numblocks;) {
uint8_t dat;
dat = this->bbt[bbtoffs + (i >> 2)];
for (j = 0; j < 4; j++, i++) {
int sftcnt = (i << (3 - sft)) & sftmsk;
- /* Do not store the reserved bbt blocks ! */
+ /* Do not store the reserved bbt blocks! */
buf[offs + (i >> sft)] &=
~(msk[dat & 0x03] << sftcnt);
dat >>= 2;
@@ -728,18 +826,20 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
memset(&einfo, 0, sizeof(einfo));
einfo.mtd = mtd;
- einfo.addr = (unsigned long)to;
+ einfo.addr = to;
einfo.len = 1 << this->bbt_erase_shift;
res = nand_erase_nand(mtd, &einfo, 1);
if (res < 0)
goto outerr;
- res = scan_write_bbt(mtd, to, len, buf, &buf[len]);
+ res = scan_write_bbt(mtd, to, len, buf,
+ td->options & NAND_BBT_NO_OOB ? NULL :
+ &buf[len]);
if (res < 0)
goto outerr;
- pr_debug("Bad block table written to 0x%08x, version "
- "0x%02X\n", (unsigned int)to, td->version[chip]);
+ pr_info("Bad block table written to 0x%012llx, version 0x%02X\n",
+ (unsigned long long)to, td->version[chip]);
/* Mark it as used */
td->pages[chip] = page;
@@ -747,27 +847,18 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
return 0;
outerr:
- pr_warning(
- "nand_bbt: Error while writing bad block table %d\n", res);
+ pr_warn("nand_bbt: error while writing bad block table %d\n", res);
return res;
}
-#else
-static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
- struct nand_bbt_descr *td, struct nand_bbt_descr *md,
- int chipsel)
-{
- return 0;
-}
-#endif
/**
* nand_memory_bbt - [GENERIC] create a memory based bad block table
- * @mtd: MTD device structure
- * @bd: descriptor for the good/bad block search pattern
+ * @mtd: MTD device structure
+ * @bd: descriptor for the good/bad block search pattern
*
- * The function creates a memory based bbt by scanning the device
- * for manufacturer / software marked good / bad blocks
-*/
+ * The function creates a memory based bbt by scanning the device for
+ * manufacturer / software marked good / bad blocks.
+ */
static inline int nand_memory_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
{
struct nand_chip *this = mtd->priv;
@@ -778,25 +869,24 @@ static inline int nand_memory_bbt(struct mtd_info *mtd, struct nand_bbt_descr *b
/**
* check_create - [GENERIC] create and write bbt(s) if necessary
- * @mtd: MTD device structure
- * @buf: temporary buffer
- * @bd: descriptor for the good/bad block search pattern
+ * @mtd: MTD device structure
+ * @buf: temporary buffer
+ * @bd: descriptor for the good/bad block search pattern
*
- * The function checks the results of the previous call to read_bbt
- * and creates / updates the bbt(s) if necessary
- * Creation is necessary if no bbt was found for the chip/device
- * Update is necessary if one of the tables is missing or the
- * version nr. of one table is less than the other
-*/
+ * The function checks the results of the previous call to read_bbt and creates
+ * / updates the bbt(s) if necessary. Creation is necessary if no bbt was found
+ * for the chip/device. Update is necessary if one of the tables is missing or
+ * the version nr. of one table is less than the other.
+ */
static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd)
{
- int i, chips, writeops, chipsel, res;
+ int i, chips, writeops, create, chipsel, res, res2;
struct nand_chip *this = mtd->priv;
struct nand_bbt_descr *td = this->bbt_td;
struct nand_bbt_descr *md = this->bbt_md;
struct nand_bbt_descr *rd, *rd2;
- /* Do we have a bbt per chip ? */
+ /* Do we have a bbt per chip? */
if (td->options & NAND_BBT_PERCHIP)
chips = this->numchips;
else
@@ -804,85 +894,98 @@ static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc
for (i = 0; i < chips; i++) {
writeops = 0;
+ create = 0;
rd = NULL;
rd2 = NULL;
- /* Per chip or per device ? */
+ res = res2 = 0;
+ /* Per chip or per device? */
chipsel = (td->options & NAND_BBT_PERCHIP) ? i : -1;
- /* Mirrored table avilable ? */
+ /* Mirrored table available? */
if (md) {
if (td->pages[i] == -1 && md->pages[i] == -1) {
+ create = 1;
writeops = 0x03;
- goto create;
- }
-
- if (td->pages[i] == -1) {
+ } else if (td->pages[i] == -1) {
rd = md;
- td->version[i] = md->version[i];
- writeops = 1;
- goto writecheck;
- }
-
- if (md->pages[i] == -1) {
+ writeops = 0x01;
+ } else if (md->pages[i] == -1) {
rd = td;
- md->version[i] = td->version[i];
- writeops = 2;
- goto writecheck;
- }
-
- if (td->version[i] == md->version[i]) {
+ writeops = 0x02;
+ } else if (td->version[i] == md->version[i]) {
rd = td;
if (!(td->options & NAND_BBT_VERSION))
rd2 = md;
- goto writecheck;
- }
-
- if (((int8_t) (td->version[i] - md->version[i])) > 0) {
+ } else if (((int8_t)(td->version[i] - md->version[i])) > 0) {
rd = td;
- md->version[i] = td->version[i];
- writeops = 2;
+ writeops = 0x02;
} else {
rd = md;
- td->version[i] = md->version[i];
- writeops = 1;
+ writeops = 0x01;
}
-
- goto writecheck;
-
} else {
if (td->pages[i] == -1) {
+ create = 1;
writeops = 0x01;
- goto create;
+ } else {
+ rd = td;
}
- rd = td;
- goto writecheck;
}
- create:
- /* Create the bad block table by scanning the device ? */
- if (!(td->options & NAND_BBT_CREATE))
- continue;
- /* Create the table in memory by scanning the chip(s) */
- create_bbt(mtd, buf, bd, chipsel);
-
- td->version[i] = 1;
- if (md)
- md->version[i] = 1;
- writecheck:
- /* read back first ? */
- if (rd)
- read_abs_bbt(mtd, buf, rd, chipsel);
- /* If they weren't versioned, read both. */
- if (rd2)
- read_abs_bbt(mtd, buf, rd2, chipsel);
-
- /* Write the bad block table to the device ? */
+ if (create) {
+ /* Create the bad block table by scanning the device? */
+ if (!(td->options & NAND_BBT_CREATE))
+ continue;
+
+ /* Create the table in memory by scanning the chip(s) */
+ if (!(this->bbt_options & NAND_BBT_CREATE_EMPTY))
+ create_bbt(mtd, buf, bd, chipsel);
+
+ td->version[i] = 1;
+ if (md)
+ md->version[i] = 1;
+ }
+
+ /* Read back first? */
+ if (rd) {
+ res = read_abs_bbt(mtd, buf, rd, chipsel);
+ if (mtd_is_eccerr(res)) {
+ /* Mark table as invalid */
+ rd->pages[i] = -1;
+ rd->version[i] = 0;
+ i--;
+ continue;
+ }
+ }
+ /* If they weren't versioned, read both */
+ if (rd2) {
+ res2 = read_abs_bbt(mtd, buf, rd2, chipsel);
+ if (mtd_is_eccerr(res2)) {
+ /* Mark table as invalid */
+ rd2->pages[i] = -1;
+ rd2->version[i] = 0;
+ i--;
+ continue;
+ }
+ }
+
+ /* Scrub the flash table(s)? */
+ if (mtd_is_bitflip(res) || mtd_is_bitflip(res2))
+ writeops = 0x03;
+
+ /* Update version numbers before writing */
+ if (md) {
+ td->version[i] = max(td->version[i], md->version[i]);
+ md->version[i] = td->version[i];
+ }
+
+ /* Write the bad block table to the device? */
if ((writeops & 0x01) && (td->options & NAND_BBT_WRITE)) {
res = write_bbt(mtd, buf, td, md, chipsel);
if (res < 0)
return res;
}
- /* Write the mirror bad block table to the device ? */
+ /* Write the mirror bad block table to the device? */
if ((writeops & 0x02) && md && (md->options & NAND_BBT_WRITE)) {
res = write_bbt(mtd, buf, md, td, chipsel);
if (res < 0)
@@ -894,20 +997,19 @@ static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc
/**
* mark_bbt_regions - [GENERIC] mark the bad block table regions
- * @mtd: MTD device structure
- * @td: bad block table descriptor
+ * @mtd: MTD device structure
+ * @td: bad block table descriptor
*
- * The bad block table regions are marked as "bad" to prevent
- * accidental erasures / writes. The regions are identified by
- * the mark 0x02.
-*/
+ * The bad block table regions are marked as "bad" to prevent accidental
+ * erasures / writes. The regions are identified by the mark 0x02.
+ */
static void mark_bbt_region(struct mtd_info *mtd, struct nand_bbt_descr *td)
{
struct nand_chip *this = mtd->priv;
int i, j, chips, block, nrblocks, update;
uint8_t oldval, newval;
- /* Do we have a bbt per chip ? */
+ /* Do we have a bbt per chip? */
if (td->options & NAND_BBT_PERCHIP) {
chips = this->numchips;
nrblocks = (int)(this->chipsize >> this->bbt_erase_shift);
@@ -927,7 +1029,7 @@ static void mark_bbt_region(struct mtd_info *mtd, struct nand_bbt_descr *td)
newval = oldval | (0x2 << (block & 0x06));
this->bbt[(block >> 3)] = newval;
if ((oldval != newval) && td->reserved_block_code)
- nand_update_bbt(mtd, block << (this->bbt_erase_shift - 1));
+ nand_update_bbt(mtd, (loff_t)block << (this->bbt_erase_shift - 1));
continue;
}
update = 0;
@@ -944,28 +1046,76 @@ static void mark_bbt_region(struct mtd_info *mtd, struct nand_bbt_descr *td)
update = 1;
block += 2;
}
- /* If we want reserved blocks to be recorded to flash, and some
- new ones have been marked, then we need to update the stored
- bbts. This should only happen once. */
+ /*
+ * If we want reserved blocks to be recorded to flash, and some
+ * new ones have been marked, then we need to update the stored
+ * bbts. This should only happen once.
+ */
if (update && td->reserved_block_code)
- nand_update_bbt(mtd, (block - 2) << (this->bbt_erase_shift - 1));
+ nand_update_bbt(mtd, (loff_t)(block - 2) << (this->bbt_erase_shift - 1));
}
}
/**
- * nand_scan_bbt - [NAND Interface] scan, find, read and maybe create bad block table(s)
- * @mtd: MTD device structure
- * @bd: descriptor for the good/bad block search pattern
+ * verify_bbt_descr - verify the bad block description
+ * @mtd: MTD device structure
+ * @bd: the table to verify
*
- * The function checks, if a bad block table(s) is/are already
- * available. If not it scans the device for manufacturer
- * marked good / bad blocks and writes the bad block table(s) to
- * the selected place.
+ * This functions performs a few sanity checks on the bad block description
+ * table.
+ */
+static void verify_bbt_descr(struct mtd_info *mtd, struct nand_bbt_descr *bd)
+{
+ struct nand_chip *this = mtd->priv;
+ u32 pattern_len;
+ u32 bits;
+ u32 table_size;
+
+ if (!bd)
+ return;
+
+ pattern_len = bd->len;
+ bits = bd->options & NAND_BBT_NRBITS_MSK;
+
+ BUG_ON((this->bbt_options & NAND_BBT_NO_OOB) &&
+ !(this->bbt_options & NAND_BBT_USE_FLASH));
+ BUG_ON(!bits);
+
+ if (bd->options & NAND_BBT_VERSION)
+ pattern_len++;
+
+ if (bd->options & NAND_BBT_NO_OOB) {
+ BUG_ON(!(this->bbt_options & NAND_BBT_USE_FLASH));
+ BUG_ON(!(this->bbt_options & NAND_BBT_NO_OOB));
+ BUG_ON(bd->offs);
+ if (bd->options & NAND_BBT_VERSION)
+ BUG_ON(bd->veroffs != bd->len);
+ BUG_ON(bd->options & NAND_BBT_SAVECONTENT);
+ }
+
+ if (bd->options & NAND_BBT_PERCHIP)
+ table_size = this->chipsize >> this->bbt_erase_shift;
+ else
+ table_size = mtd->size >> this->bbt_erase_shift;
+ table_size >>= 3;
+ table_size *= bits;
+ if (bd->options & NAND_BBT_NO_OOB)
+ table_size += pattern_len;
+ BUG_ON(table_size > (1 << this->bbt_erase_shift));
+}
+
+/**
+ * nand_scan_bbt - [NAND Interface] scan, find, read and maybe create bad block table(s)
+ * @mtd: MTD device structure
+ * @bd: descriptor for the good/bad block search pattern
*
- * The bad block table memory is allocated here. It must be freed
- * by calling the nand_free_bbt function.
+ * The function checks, if a bad block table(s) is/are already available. If
+ * not it scans the device for manufacturer marked good / bad blocks and writes
+ * the bad block table(s) to the selected place.
*
-*/
+ * The bad block table memory is allocated here. It must be freed by calling
+ * the nand_free_bbt function.
+ */
int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
{
struct nand_chip *this = mtd->priv;
@@ -975,46 +1125,48 @@ int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
struct nand_bbt_descr *md = this->bbt_md;
len = mtd->size >> (this->bbt_erase_shift + 2);
- /* Allocate memory (2bit per block) and clear the memory bad block table */
+ /*
+ * Allocate memory (2bit per block) and clear the memory bad block
+ * table.
+ */
this->bbt = kzalloc(len, GFP_KERNEL);
- if (!this->bbt) {
- pr_err("nand_scan_bbt: Out of memory\n");
+ if (!this->bbt)
return -ENOMEM;
- }
- /* If no primary table decriptor is given, scan the device
- * to build a memory based bad block table
+ /*
+ * If no primary table decriptor is given, scan the device to build a
+ * memory based bad block table.
*/
if (!td) {
if ((res = nand_memory_bbt(mtd, bd))) {
- pr_err("nand_bbt: Can't scan flash and build the RAM-based BBT\n");
+ pr_err("nand_bbt: can't scan flash and build the RAM-based BBT\n");
kfree(this->bbt);
this->bbt = NULL;
}
return res;
}
+ verify_bbt_descr(mtd, td);
+ verify_bbt_descr(mtd, md);
/* Allocate a temporary buffer for one eraseblock incl. oob */
len = (1 << this->bbt_erase_shift);
len += (len >> this->page_shift) * mtd->oobsize;
buf = vmalloc(len);
if (!buf) {
- pr_err("nand_bbt: Out of memory\n");
kfree(this->bbt);
this->bbt = NULL;
return -ENOMEM;
}
- /* Is the bbt at a given page ? */
+ /* Is the bbt at a given page? */
if (td->options & NAND_BBT_ABSPAGE) {
- res = read_abs_bbts(mtd, buf, td, md);
+ read_abs_bbts(mtd, buf, td, md);
} else {
/* Search the bad block table using a pattern in oob */
- res = search_read_bbts(mtd, buf, td, md);
+ search_read_bbts(mtd, buf, td, md);
}
- if (res)
- res = check_create(mtd, buf, bd);
+ res = check_create(mtd, buf, bd);
/* Prevent the bbt regions from erasing / writing */
mark_bbt_region(mtd, td);
@@ -1027,15 +1179,15 @@ int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
/**
* nand_update_bbt - [NAND Interface] update bad block table(s)
- * @mtd: MTD device structure
- * @offs: the offset of the newly marked block
+ * @mtd: MTD device structure
+ * @offs: the offset of the newly marked block
*
- * The function updates the bad block table(s)
-*/
+ * The function updates the bad block table(s).
+ */
int nand_update_bbt(struct mtd_info *mtd, loff_t offs)
{
struct nand_chip *this = mtd->priv;
- int len, res = 0, writeops = 0;
+ int len, res = 0;
int chip, chipsel;
uint8_t *buf;
struct nand_bbt_descr *td = this->bbt_td;
@@ -1044,19 +1196,14 @@ int nand_update_bbt(struct mtd_info *mtd, loff_t offs)
if (!this->bbt || !td)
return -EINVAL;
- len = mtd->size >> (this->bbt_erase_shift + 2);
/* Allocate a temporary buffer for one eraseblock incl. oob */
len = (1 << this->bbt_erase_shift);
len += (len >> this->page_shift) * mtd->oobsize;
buf = kmalloc(len, GFP_KERNEL);
- if (!buf) {
- pr_err("nand_update_bbt: Out of memory\n");
+ if (!buf)
return -ENOMEM;
- }
- writeops = md != NULL ? 0x03 : 0x01;
-
- /* Do we have a bbt per chip ? */
+ /* Do we have a bbt per chip? */
if (td->options & NAND_BBT_PERCHIP) {
chip = (int)(offs >> this->chip_shift);
chipsel = chip;
@@ -1069,14 +1216,14 @@ int nand_update_bbt(struct mtd_info *mtd, loff_t offs)
if (md)
md->version[chip]++;
- /* Write the bad block table to the device ? */
- if ((writeops & 0x01) && (td->options & NAND_BBT_WRITE)) {
+ /* Write the bad block table to the device? */
+ if (td->options & NAND_BBT_WRITE) {
res = write_bbt(mtd, buf, td, md, chipsel);
if (res < 0)
goto out;
}
- /* Write the mirror bad block table to the device ? */
- if ((writeops & 0x02) && md && (md->options & NAND_BBT_WRITE)) {
+ /* Write the mirror bad block table to the device? */
+ if (md && (md->options & NAND_BBT_WRITE)) {
res = write_bbt(mtd, buf, md, td, chipsel);
}
@@ -1085,49 +1232,13 @@ int nand_update_bbt(struct mtd_info *mtd, loff_t offs)
return res;
}
-/* Define some generic bad / good block scan pattern which are used
- * while scanning a device for factory marked good / bad blocks. */
+/*
+ * Define some generic bad / good block scan pattern which are used
+ * while scanning a device for factory marked good / bad blocks.
+ */
static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
-static struct nand_bbt_descr smallpage_memorybased = {
- .options = NAND_BBT_SCAN2NDPAGE,
- .offs = 5,
- .len = 1,
- .pattern = scan_ff_pattern
-};
-
-static struct nand_bbt_descr largepage_memorybased = {
- .options = 0,
- .offs = 0,
- .len = 2,
- .pattern = scan_ff_pattern
-};
-
-static struct nand_bbt_descr smallpage_flashbased = {
- .options = NAND_BBT_SCAN2NDPAGE,
- .offs = 5,
- .len = 1,
- .pattern = scan_ff_pattern
-};
-
-static struct nand_bbt_descr largepage_flashbased = {
- .options = NAND_BBT_SCAN2NDPAGE,
- .offs = 0,
- .len = 2,
- .pattern = scan_ff_pattern
-};
-
-static uint8_t scan_agand_pattern[] = { 0x1C, 0x71, 0xC7, 0x1C, 0x71, 0xC7 };
-
-static struct nand_bbt_descr agand_flashbased = {
- .options = NAND_BBT_SCANEMPTY | NAND_BBT_SCANALLPAGES,
- .offs = 0x20,
- .len = 6,
- .pattern = scan_agand_pattern
-};
-
-/* Generic flash bbt decriptors
-*/
+/* Generic flash bbt descriptors */
static uint8_t bbt_pattern[] = {'B', 'b', 't', '0' };
static uint8_t mirror_pattern[] = {'1', 't', 'b', 'B' };
@@ -1137,7 +1248,7 @@ static struct nand_bbt_descr bbt_main_descr = {
.offs = 8,
.len = 4,
.veroffs = 12,
- .maxblocks = 4,
+ .maxblocks = NAND_BBT_SCAN_MAXBLOCKS,
.pattern = bbt_pattern
};
@@ -1147,67 +1258,99 @@ static struct nand_bbt_descr bbt_mirror_descr = {
.offs = 8,
.len = 4,
.veroffs = 12,
- .maxblocks = 4,
+ .maxblocks = NAND_BBT_SCAN_MAXBLOCKS,
.pattern = mirror_pattern
};
+static struct nand_bbt_descr bbt_main_no_oob_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP
+ | NAND_BBT_NO_OOB,
+ .len = 4,
+ .veroffs = 4,
+ .maxblocks = NAND_BBT_SCAN_MAXBLOCKS,
+ .pattern = bbt_pattern
+};
+
+static struct nand_bbt_descr bbt_mirror_no_oob_descr = {
+ .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE
+ | NAND_BBT_2BIT | NAND_BBT_VERSION | NAND_BBT_PERCHIP
+ | NAND_BBT_NO_OOB,
+ .len = 4,
+ .veroffs = 4,
+ .maxblocks = NAND_BBT_SCAN_MAXBLOCKS,
+ .pattern = mirror_pattern
+};
+
+#define BADBLOCK_SCAN_MASK (~NAND_BBT_NO_OOB)
/**
- * nand_default_bbt - [NAND Interface] Select a default bad block table for the device
- * @mtd: MTD device structure
+ * nand_create_badblock_pattern - [INTERN] Creates a BBT descriptor structure
+ * @this: NAND chip to create descriptor for
*
- * This function selects the default bad block table
- * support for the device and calls the nand_scan_bbt function
+ * This function allocates and initializes a nand_bbt_descr for BBM detection
+ * based on the properties of @this. The new descriptor is stored in
+ * this->badblock_pattern. Thus, this->badblock_pattern should be NULL when
+ * passed to this function.
+ */
+static int nand_create_badblock_pattern(struct nand_chip *this)
+{
+ struct nand_bbt_descr *bd;
+ if (this->badblock_pattern) {
+ pr_warn("Bad block pattern already allocated; not replacing\n");
+ return -EINVAL;
+ }
+ bd = kzalloc(sizeof(*bd), GFP_KERNEL);
+ if (!bd)
+ return -ENOMEM;
+ bd->options = this->bbt_options & BADBLOCK_SCAN_MASK;
+ bd->offs = this->badblockpos;
+ bd->len = (this->options & NAND_BUSWIDTH_16) ? 2 : 1;
+ bd->pattern = scan_ff_pattern;
+ bd->options |= NAND_BBT_DYNAMICSTRUCT;
+ this->badblock_pattern = bd;
+ return 0;
+}
+
+/**
+ * nand_default_bbt - [NAND Interface] Select a default bad block table for the device
+ * @mtd: MTD device structure
*
-*/
+ * This function selects the default bad block table support for the device and
+ * calls the nand_scan_bbt function.
+ */
int nand_default_bbt(struct mtd_info *mtd)
{
struct nand_chip *this = mtd->priv;
- /* Default for AG-AND. We must use a flash based
- * bad block table as the devices have factory marked
- * _good_ blocks. Erasing those blocks leads to loss
- * of the good / bad information, so we _must_ store
- * this information in a good / bad table during
- * startup
- */
- if (this->options & NAND_IS_AND) {
- /* Use the default pattern descriptors */
- if (!this->bbt_td) {
- this->bbt_td = &bbt_main_descr;
- this->bbt_md = &bbt_mirror_descr;
- }
- this->bbt_options |= NAND_BBT_USE_FLASH;
- return nand_scan_bbt(mtd, &agand_flashbased);
- }
-
- /* Is a flash based bad block table requested ? */
+ /* Is a flash based bad block table requested? */
if (this->bbt_options & NAND_BBT_USE_FLASH) {
/* Use the default pattern descriptors */
if (!this->bbt_td) {
- this->bbt_td = &bbt_main_descr;
- this->bbt_md = &bbt_mirror_descr;
- }
- if (!this->badblock_pattern) {
- this->badblock_pattern = (mtd->writesize > 512) ? &largepage_flashbased : &smallpage_flashbased;
+ if (this->bbt_options & NAND_BBT_NO_OOB) {
+ this->bbt_td = &bbt_main_no_oob_descr;
+ this->bbt_md = &bbt_mirror_no_oob_descr;
+ } else {
+ this->bbt_td = &bbt_main_descr;
+ this->bbt_md = &bbt_mirror_descr;
+ }
}
} else {
this->bbt_td = NULL;
this->bbt_md = NULL;
- if (!this->badblock_pattern) {
- this->badblock_pattern = (mtd->writesize > 512) ?
- &largepage_memorybased : &smallpage_memorybased;
- }
}
+
+ if (!this->badblock_pattern)
+ nand_create_badblock_pattern(this);
+
return nand_scan_bbt(mtd, this->badblock_pattern);
}
/**
* nand_isbad_bbt - [NAND Interface] Check if a block is bad
- * @mtd: MTD device structure
- * @offs: offset in the device
- * @allowbbt: allow access to bad block table region
- *
-*/
+ * @mtd: MTD device structure
+ * @offs: offset in the device
+ * @allowbbt: allow access to bad block table region
+ */
int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt)
{
struct nand_chip *this = mtd->priv;
@@ -1218,8 +1361,9 @@ int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt)
block = (int)(offs >> (this->bbt_erase_shift - 1));
res = (this->bbt[block >> 3] >> (block & 0x06)) & 0x03;
- MTD_DEBUG(MTD_DEBUG_LEVEL2, "nand_isbad_bbt(): bbt info for offs 0x%08x: (block %d) 0x%02x\n",
- (unsigned int)offs, block >> 1, res);
+ pr_debug("nand_isbad_bbt(): bbt info for offs 0x%08x: "
+ "(block %d) 0x%02x\n",
+ (unsigned int)offs, block >> 1, res);
switch ((int)res) {
case 0x00:
@@ -1234,5 +1378,4 @@ int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt)
EXPORT_SYMBOL(nand_scan_bbt);
EXPORT_SYMBOL(nand_default_bbt);
-
-#endif /* DOXYGEN_SHOULD_SKIP_THIS */
+EXPORT_SYMBOL_GPL(nand_update_bbt);
diff --git a/drivers/mtd/nand/nand_bch.c b/drivers/mtd/nand/nand_bch.c
new file mode 100644
index 0000000..cba5285
--- /dev/null
+++ b/drivers/mtd/nand/nand_bch.c
@@ -0,0 +1,243 @@
+/*
+ * This file provides ECC correction for more than 1 bit per block of data,
+ * using binary BCH codes. It relies on the generic BCH library lib/bch.c.
+ *
+ * Copyright © 2011 Ivan Djelic <ivan.djelic@parrot.com>
+ *
+ * This file is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 or (at your option) any
+ * later version.
+ *
+ * This file is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this file; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_bch.h>
+#include <linux/bch.h>
+
+/**
+ * struct nand_bch_control - private NAND BCH control structure
+ * @bch: BCH control structure
+ * @ecclayout: private ecc layout for this BCH configuration
+ * @errloc: error location array
+ * @eccmask: XOR ecc mask, allows erased pages to be decoded as valid
+ */
+struct nand_bch_control {
+ struct bch_control *bch;
+ struct nand_ecclayout ecclayout;
+ unsigned int *errloc;
+ unsigned char *eccmask;
+};
+
+/**
+ * nand_bch_calculate_ecc - [NAND Interface] Calculate ECC for data block
+ * @mtd: MTD block structure
+ * @buf: input buffer with raw data
+ * @code: output buffer with ECC
+ */
+int nand_bch_calculate_ecc(struct mtd_info *mtd, const unsigned char *buf,
+ unsigned char *code)
+{
+ const struct nand_chip *chip = mtd->priv;
+ struct nand_bch_control *nbc = chip->ecc.priv;
+ unsigned int i;
+
+ memset(code, 0, chip->ecc.bytes);
+ encode_bch(nbc->bch, buf, chip->ecc.size, code);
+
+ /* apply mask so that an erased page is a valid codeword */
+ for (i = 0; i < chip->ecc.bytes; i++)
+ code[i] ^= nbc->eccmask[i];
+
+ return 0;
+}
+EXPORT_SYMBOL(nand_bch_calculate_ecc);
+
+/**
+ * nand_bch_correct_data - [NAND Interface] Detect and correct bit error(s)
+ * @mtd: MTD block structure
+ * @buf: raw data read from the chip
+ * @read_ecc: ECC from the chip
+ * @calc_ecc: the ECC calculated from raw data
+ *
+ * Detect and correct bit errors for a data byte block
+ */
+int nand_bch_correct_data(struct mtd_info *mtd, unsigned char *buf,
+ unsigned char *read_ecc, unsigned char *calc_ecc)
+{
+ const struct nand_chip *chip = mtd->priv;
+ struct nand_bch_control *nbc = chip->ecc.priv;
+ unsigned int *errloc = nbc->errloc;
+ int i, count;
+
+ count = decode_bch(nbc->bch, NULL, chip->ecc.size, read_ecc, calc_ecc,
+ NULL, errloc);
+ if (count > 0) {
+ for (i = 0; i < count; i++) {
+ if (errloc[i] < (chip->ecc.size*8))
+ /* error is located in data, correct it */
+ buf[errloc[i] >> 3] ^= (1 << (errloc[i] & 7));
+ /* else error in ecc, no action needed */
+
+ pr_debug("%s: corrected bitflip %u\n", __func__,
+ errloc[i]);
+ }
+ } else if (count < 0) {
+ printk(KERN_ERR "ecc unrecoverable error\n");
+ count = -1;
+ }
+ return count;
+}
+EXPORT_SYMBOL(nand_bch_correct_data);
+
+/**
+ * nand_bch_init - [NAND Interface] Initialize NAND BCH error correction
+ * @mtd: MTD block structure
+ * @eccsize: ecc block size in bytes
+ * @eccbytes: ecc length in bytes
+ * @ecclayout: output default layout
+ *
+ * Returns:
+ * a pointer to a new NAND BCH control structure, or NULL upon failure
+ *
+ * Initialize NAND BCH error correction. Parameters @eccsize and @eccbytes
+ * are used to compute BCH parameters m (Galois field order) and t (error
+ * correction capability). @eccbytes should be equal to the number of bytes
+ * required to store m*t bits, where m is such that 2^m-1 > @eccsize*8.
+ *
+ * Example: to configure 4 bit correction per 512 bytes, you should pass
+ * @eccsize = 512 (thus, m=13 is the smallest integer such that 2^m-1 > 512*8)
+ * @eccbytes = 7 (7 bytes are required to store m*t = 13*4 = 52 bits)
+ */
+struct nand_bch_control *
+nand_bch_init(struct mtd_info *mtd, unsigned int eccsize, unsigned int eccbytes,
+ struct nand_ecclayout **ecclayout)
+{
+ unsigned int m, t, eccsteps, i;
+ struct nand_ecclayout *layout;
+ struct nand_bch_control *nbc = NULL;
+ unsigned char *erased_page;
+
+ if (!eccsize || !eccbytes) {
+ printk(KERN_WARNING "ecc parameters not supplied\n");
+ goto fail;
+ }
+
+ m = fls(1+8*eccsize);
+ t = (eccbytes*8)/m;
+
+ nbc = kzalloc(sizeof(*nbc), GFP_KERNEL);
+ if (!nbc)
+ goto fail;
+
+ nbc->bch = init_bch(m, t, 0);
+ if (!nbc->bch)
+ goto fail;
+
+ /* verify that eccbytes has the expected value */
+ if (nbc->bch->ecc_bytes != eccbytes) {
+ printk(KERN_WARNING "invalid eccbytes %u, should be %u\n",
+ eccbytes, nbc->bch->ecc_bytes);
+ goto fail;
+ }
+
+ eccsteps = mtd->writesize/eccsize;
+
+ /* if no ecc placement scheme was provided, build one */
+ if (!*ecclayout) {
+
+ /* handle large page devices only */
+ if (mtd->oobsize < 64) {
+ printk(KERN_WARNING "must provide an oob scheme for "
+ "oobsize %d\n", mtd->oobsize);
+ goto fail;
+ }
+
+ layout = &nbc->ecclayout;
+ layout->eccbytes = eccsteps*eccbytes;
+
+ /* reserve 2 bytes for bad block marker */
+ if (layout->eccbytes+2 > mtd->oobsize) {
+ printk(KERN_WARNING "no suitable oob scheme available "
+ "for oobsize %d eccbytes %u\n", mtd->oobsize,
+ eccbytes);
+ goto fail;
+ }
+ /* put ecc bytes at oob tail */
+ for (i = 0; i < layout->eccbytes; i++)
+ layout->eccpos[i] = mtd->oobsize-layout->eccbytes+i;
+
+ layout->oobfree[0].offset = 2;
+ layout->oobfree[0].length = mtd->oobsize-2-layout->eccbytes;
+
+ *ecclayout = layout;
+ }
+
+ /* sanity checks */
+ if (8*(eccsize+eccbytes) >= (1 << m)) {
+ printk(KERN_WARNING "eccsize %u is too large\n", eccsize);
+ goto fail;
+ }
+ if ((*ecclayout)->eccbytes != (eccsteps*eccbytes)) {
+ printk(KERN_WARNING "invalid ecc layout\n");
+ goto fail;
+ }
+
+ nbc->eccmask = kmalloc(eccbytes, GFP_KERNEL);
+ nbc->errloc = kmalloc(t*sizeof(*nbc->errloc), GFP_KERNEL);
+ if (!nbc->eccmask || !nbc->errloc)
+ goto fail;
+ /*
+ * compute and store the inverted ecc of an erased ecc block
+ */
+ erased_page = kmalloc(eccsize, GFP_KERNEL);
+ if (!erased_page)
+ goto fail;
+
+ memset(erased_page, 0xff, eccsize);
+ memset(nbc->eccmask, 0, eccbytes);
+ encode_bch(nbc->bch, erased_page, eccsize, nbc->eccmask);
+ kfree(erased_page);
+
+ for (i = 0; i < eccbytes; i++)
+ nbc->eccmask[i] ^= 0xff;
+
+ return nbc;
+fail:
+ nand_bch_free(nbc);
+ return NULL;
+}
+EXPORT_SYMBOL(nand_bch_init);
+
+/**
+ * nand_bch_free - [NAND Interface] Release NAND BCH ECC resources
+ * @nbc: NAND BCH control structure
+ */
+void nand_bch_free(struct nand_bch_control *nbc)
+{
+ if (nbc) {
+ free_bch(nbc->bch);
+ kfree(nbc->errloc);
+ kfree(nbc->eccmask);
+ kfree(nbc);
+ }
+}
+EXPORT_SYMBOL(nand_bch_free);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Ivan Djelic <ivan.djelic@parrot.com>");
+MODULE_DESCRIPTION("NAND software BCH ECC support");
diff --git a/drivers/mtd/nand/nand_hwecc.c b/drivers/mtd/nand/nand_hwecc.c
deleted file mode 100644
index a48efa1..0000000
--- a/drivers/mtd/nand/nand_hwecc.c
+++ /dev/null
@@ -1,103 +0,0 @@
-#include <common.h>
-#include <errno.h>
-#include <clock.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/err.h>
-#include <linux/mtd/nand_ecc.h>
-#include <asm/byteorder.h>
-#include <io.h>
-#include <malloc.h>
-
-#include "nand.h"
-
-/**
- * nand_read_page_hwecc - [REPLACABLE] hardware ecc based page read function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- *
- * Not for syndrome calculating ecc controllers which need a special oob layout
- */
-static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf)
-{
- int i, eccsize = chip->ecc.size;
- int eccbytes = chip->ecc.bytes;
- int eccsteps = chip->ecc.steps;
- uint8_t *p = buf;
- uint8_t *ecc_calc = chip->buffers->ecccalc;
- uint8_t *ecc_code = chip->buffers->ecccode;
- uint32_t *eccpos = chip->ecc.layout->eccpos;
-
- for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
- chip->ecc.hwctl(mtd, NAND_ECC_READ);
- chip->read_buf(mtd, p, eccsize);
- chip->ecc.calculate(mtd, p, &ecc_calc[i]);
- }
- chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
-
- for (i = 0; i < chip->ecc.total; i++)
- ecc_code[i] = chip->oob_poi[eccpos[i]];
-
- eccsteps = chip->ecc.steps;
- p = buf;
-
- for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
- int stat;
-
- stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
- if (stat < 0)
- mtd->ecc_stats.failed++;
- else
- mtd->ecc_stats.corrected += stat;
- }
- return 0;
-}
-
-/**
- * nand_write_page_hwecc - [REPLACABLE] hardware ecc based page write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: data buffer
- */
-#ifdef CONFIG_MTD_WRITE
-static void nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf)
-{
- int i, eccsize = chip->ecc.size;
- int eccbytes = chip->ecc.bytes;
- int eccsteps = chip->ecc.steps;
- uint8_t *ecc_calc = chip->buffers->ecccalc;
- const uint8_t *p = buf;
- uint32_t *eccpos = chip->ecc.layout->eccpos;
-
- for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
- chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
- chip->write_buf(mtd, p, eccsize);
- chip->ecc.calculate(mtd, p, &ecc_calc[i]);
- }
-
- for (i = 0; i < chip->ecc.total; i++)
- chip->oob_poi[eccpos[i]] = ecc_calc[i];
-
- chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
-}
-#endif
-
-void nand_init_ecc_hw(struct nand_chip *chip)
-{
- /* Use standard hwecc read page function ? */
- if (!chip->ecc.read_page)
- chip->ecc.read_page = nand_read_page_hwecc;
-#ifdef CONFIG_NAND_READ_OOB
- if (!chip->ecc.read_oob)
- chip->ecc.read_oob = nand_read_oob_std;
-#endif
-#ifdef CONFIG_MTD_WRITE
- if (!chip->ecc.write_oob)
- chip->ecc.write_oob = nand_write_oob_std;
- if (!chip->ecc.write_page)
- chip->ecc.write_page = nand_write_page_hwecc;
-#endif
-}
diff --git a/drivers/mtd/nand/nand_hwecc_syndrome.c b/drivers/mtd/nand/nand_hwecc_syndrome.c
deleted file mode 100644
index 1493b88..0000000
--- a/drivers/mtd/nand/nand_hwecc_syndrome.c
+++ /dev/null
@@ -1,225 +0,0 @@
-#include <common.h>
-#include <errno.h>
-#include <clock.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/err.h>
-#include <linux/mtd/nand_ecc.h>
-#include <asm/byteorder.h>
-#include <io.h>
-#include <malloc.h>
-#include <module.h>
-
-/**
- * nand_read_page_syndrome - [REPLACABLE] hardware ecc syndrom based page read
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- *
- * The hw generator calculates the error syndrome automatically. Therefor
- * we need a special oob layout and handling.
- */
-static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf)
-{
- int i, eccsize = chip->ecc.size;
- int eccbytes = chip->ecc.bytes;
- int eccsteps = chip->ecc.steps;
- uint8_t *p = buf;
- uint8_t *oob = chip->oob_poi;
-
- for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
- int stat;
-
- chip->ecc.hwctl(mtd, NAND_ECC_READ);
- chip->read_buf(mtd, p, eccsize);
-
- if (chip->ecc.prepad) {
- chip->read_buf(mtd, oob, chip->ecc.prepad);
- oob += chip->ecc.prepad;
- }
-
- chip->ecc.hwctl(mtd, NAND_ECC_READSYN);
- chip->read_buf(mtd, oob, eccbytes);
- stat = chip->ecc.correct(mtd, p, oob, NULL);
-
- if (stat < 0)
- mtd->ecc_stats.failed++;
- else
- mtd->ecc_stats.corrected += stat;
-
- oob += eccbytes;
-
- if (chip->ecc.postpad) {
- chip->read_buf(mtd, oob, chip->ecc.postpad);
- oob += chip->ecc.postpad;
- }
- }
-
- /* Calculate remaining oob bytes */
- i = mtd->oobsize - (oob - chip->oob_poi);
- if (i)
- chip->read_buf(mtd, oob, i);
-
- return 0;
-}
-/**
- * nand_write_page_syndrome - [REPLACABLE] hardware ecc syndrom based page write
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: data buffer
- *
- * The hw generator calculates the error syndrome automatically. Therefor
- * we need a special oob layout and handling.
- */
-#ifdef CONFIG_MTD_WRITE
-static void nand_write_page_syndrome(struct mtd_info *mtd,
- struct nand_chip *chip, const uint8_t *buf)
-{
- int i, eccsize = chip->ecc.size;
- int eccbytes = chip->ecc.bytes;
- int eccsteps = chip->ecc.steps;
- const uint8_t *p = buf;
- uint8_t *oob = chip->oob_poi;
-
- for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
-
- chip->ecc.hwctl(mtd, NAND_ECC_WRITE);
- chip->write_buf(mtd, p, eccsize);
-
- if (chip->ecc.prepad) {
- chip->write_buf(mtd, oob, chip->ecc.prepad);
- oob += chip->ecc.prepad;
- }
-
- chip->ecc.calculate(mtd, p, oob);
- chip->write_buf(mtd, oob, eccbytes);
- oob += eccbytes;
-
- if (chip->ecc.postpad) {
- chip->write_buf(mtd, oob, chip->ecc.postpad);
- oob += chip->ecc.postpad;
- }
- }
-
- /* Calculate remaining oob bytes */
- i = mtd->oobsize - (oob - chip->oob_poi);
- if (i)
- chip->write_buf(mtd, oob, i);
-}
-#endif
-
-/**
- * nand_read_oob_syndrome - [REPLACABLE] OOB data read function for HW ECC
- * with syndromes
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @page: page number to read
- * @sndcmd: flag whether to issue read command or not
- */
-static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
- int page, int sndcmd)
-{
- uint8_t *buf = chip->oob_poi;
- int length = mtd->oobsize;
- int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad;
- int eccsize = chip->ecc.size;
- uint8_t *bufpoi = buf;
- int i, toread, sndrnd = 0, pos;
-
- chip->cmdfunc(mtd, NAND_CMD_READ0, chip->ecc.size, page);
- for (i = 0; i < chip->ecc.steps; i++) {
- if (sndrnd) {
- pos = eccsize + i * (eccsize + chunk);
- if (mtd->writesize > 512)
- chip->cmdfunc(mtd, NAND_CMD_RNDOUT, pos, -1);
- else
- chip->cmdfunc(mtd, NAND_CMD_READ0, pos, page);
- } else
- sndrnd = 1;
- toread = min_t(int, length, chunk);
- chip->read_buf(mtd, bufpoi, toread);
- bufpoi += toread;
- length -= toread;
- }
- if (length > 0)
- chip->read_buf(mtd, bufpoi, length);
-
- return 1;
-}
-
-/**
- * nand_write_oob_syndrome - [REPLACABLE] OOB data write function for HW ECC
- * with syndrome - only for large page flash !
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @page: page number to write
- */
-#ifdef CONFIG_MTD_WRITE
-static int nand_write_oob_syndrome(struct mtd_info *mtd,
- struct nand_chip *chip, int page)
-{
- int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad;
- int eccsize = chip->ecc.size, length = mtd->oobsize;
- int i, len, pos, status = 0, sndcmd = 0, steps = chip->ecc.steps;
- const uint8_t *bufpoi = chip->oob_poi;
-
- /*
- * data-ecc-data-ecc ... ecc-oob
- * or
- * data-pad-ecc-pad-data-pad .... ecc-pad-oob
- */
- if (!chip->ecc.prepad && !chip->ecc.postpad) {
- pos = steps * (eccsize + chunk);
- steps = 0;
- } else
- pos = eccsize;
-
- chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page);
- for (i = 0; i < steps; i++) {
- if (sndcmd) {
- if (mtd->writesize <= 512) {
- uint32_t fill = 0xFFFFFFFF;
-
- len = eccsize;
- while (len > 0) {
- int num = min_t(int, len, 4);
- chip->write_buf(mtd, (uint8_t *)&fill,
- num);
- len -= num;
- }
- } else {
- pos = eccsize + i * (eccsize + chunk);
- chip->cmdfunc(mtd, NAND_CMD_RNDIN, pos, -1);
- }
- } else
- sndcmd = 1;
- len = min_t(int, length, chunk);
- chip->write_buf(mtd, bufpoi, len);
- bufpoi += len;
- length -= len;
- }
- if (length > 0)
- chip->write_buf(mtd, bufpoi, length);
-
- chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
- status = chip->waitfunc(mtd, chip);
-
- return status & NAND_STATUS_FAIL ? -EIO : 0;
-}
-#endif
-
-void nand_init_ecc_hw_syndrome(struct nand_chip *chip)
-{
- /* Use standard syndrome read/write page function ? */
- if (!chip->ecc.read_page)
- chip->ecc.read_page = nand_read_page_syndrome;
- if (!chip->ecc.read_oob)
- chip->ecc.read_oob = nand_read_oob_syndrome;
-#ifdef CONFIG_MTD_WRITE
- if (!chip->ecc.write_page)
- chip->ecc.write_page = nand_write_page_syndrome;
- if (!chip->ecc.write_oob)
- chip->ecc.write_oob = nand_write_oob_syndrome;
-#endif
-}
diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/nand_ids.c
index 4f8fb02..52b0da5 100644
--- a/drivers/mtd/nand/nand_ids.c
+++ b/drivers/mtd/nand/nand_ids.c
@@ -3,184 +3,178 @@
*
* Copyright (C) 2002 Thomas Gleixner (tglx@linutronix.de)
*
- * $Id: nand_ids.c,v 1.16 2005/11/07 11:14:31 gleixner Exp $
- *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <common.h>
+#include <sizes.h>
#include <linux/mtd/nand.h>
#ifdef CONFIG_NAND_INFO
-#define __NANDSTR(str) str
+#define __STR(str) str
#else
-#define __NANDSTR(str) ""
-#endif
-
-/*
-* Chip ID list
-*
-* Name. ID code, pagesize, chipsize in MegaByte, eraseblock size,
-* options
-*
-* Pagesize; 0, 256, 512
-* 0 get this information from the extended chip ID
-+ 256 256 Byte page size
-* 512 512 Byte page size
-*/
-struct nand_flash_dev nand_flash_ids[] = {
-
-#ifdef CONFIG_MTD_NAND_MUSEUM_IDS
- {__NANDSTR("NAND 1MiB 5V 8-bit"), 0x6e, 256, 1, 0x1000, 0},
- {__NANDSTR("NAND 2MiB 5V 8-bit"), 0x64, 256, 2, 0x1000, 0},
- {__NANDSTR("NAND 4MiB 5V 8-bit"), 0x6b, 512, 4, 0x2000, 0},
- {__NANDSTR("NAND 1MiB 3,3V 8-bit"), 0xe8, 256, 1, 0x1000, 0},
- {__NANDSTR("NAND 1MiB 3,3V 8-bit"), 0xec, 256, 1, 0x1000, 0},
- {__NANDSTR("NAND 2MiB 3,3V 8-bit"), 0xea, 256, 2, 0x1000, 0},
- {__NANDSTR("NAND 4MiB 3,3V 8-bit"), 0xd5, 512, 4, 0x2000, 0},
- {__NANDSTR("NAND 4MiB 3,3V 8-bit"), 0xe3, 512, 4, 0x2000, 0},
- {__NANDSTR("NAND 4MiB 3,3V 8-bit"), 0xe5, 512, 4, 0x2000, 0},
- {__NANDSTR("NAND 8MiB 3,3V 8-bit"), 0xd6, 512, 8, 0x2000, 0},
-
- {__NANDSTR("NAND 8MiB 1,8V 8-bit"), 0x39, 512, 8, 0x2000, 0},
- {__NANDSTR("NAND 8MiB 3,3V 8-bit"), 0xe6, 512, 8, 0x2000, 0},
- {__NANDSTR("NAND 8MiB 1,8V 16-bit"), 0x49, 512, 8, 0x2000, NAND_BUSWIDTH_16},
- {__NANDSTR("NAND 8MiB 3,3V 16-bit"), 0x59, 512, 8, 0x2000, NAND_BUSWIDTH_16},
+#define __STR(str) ""
#endif
- {__NANDSTR("NAND 16MiB 1,8V 8-bit"), 0x33, 512, 16, 0x4000, 0},
- {__NANDSTR("NAND 16MiB 3,3V 8-bit"), 0x73, 512, 16, 0x4000, 0},
- {__NANDSTR("NAND 16MiB 1,8V 16-bit"), 0x43, 512, 16, 0x4000, NAND_BUSWIDTH_16},
- {__NANDSTR("NAND 16MiB 3,3V 16-bit"), 0x53, 512, 16, 0x4000, NAND_BUSWIDTH_16},
-
- {__NANDSTR("NAND 32MiB 1,8V 8-bit"), 0x35, 512, 32, 0x4000, 0},
- {__NANDSTR("NAND 32MiB 3,3V 8-bit"), 0x75, 512, 32, 0x4000, 0},
- {__NANDSTR("NAND 32MiB 1,8V 16-bit"), 0x45, 512, 32, 0x4000, NAND_BUSWIDTH_16},
- {__NANDSTR("NAND 32MiB 3,3V 16-bit"), 0x55, 512, 32, 0x4000, NAND_BUSWIDTH_16},
-
- {__NANDSTR("NAND 64MiB 1,8V 8-bit"), 0x36, 512, 64, 0x4000, 0},
- {__NANDSTR("NAND 64MiB 3,3V 8-bit"), 0x76, 512, 64, 0x4000, 0},
- {__NANDSTR("NAND 64MiB 1,8V 16-bit"), 0x46, 512, 64, 0x4000, NAND_BUSWIDTH_16},
- {__NANDSTR("NAND 64MiB 3,3V 16-bit"), 0x56, 512, 64, 0x4000, NAND_BUSWIDTH_16},
+#define LP_OPTIONS NAND_SAMSUNG_LP_OPTIONS
+#define LP_OPTIONS16 (LP_OPTIONS | NAND_BUSWIDTH_16)
- {__NANDSTR("NAND 128MiB 1,8V 8-bit"), 0x78, 512, 128, 0x4000, 0},
- {__NANDSTR("NAND 128MiB 1,8V 8-bit"), 0x39, 512, 128, 0x4000, 0},
- {__NANDSTR("NAND 128MiB 3,3V 8-bit"), 0x79, 512, 128, 0x4000, 0},
- {__NANDSTR("NAND 128MiB 1,8V 16-bit"), 0x72, 512, 128, 0x4000, NAND_BUSWIDTH_16},
- {__NANDSTR("NAND 128MiB 1,8V 16-bit"), 0x49, 512, 128, 0x4000, NAND_BUSWIDTH_16},
- {__NANDSTR("NAND 128MiB 3,3V 16-bit"), 0x74, 512, 128, 0x4000, NAND_BUSWIDTH_16},
- {__NANDSTR("NAND 128MiB 3,3V 16-bit"), 0x59, 512, 128, 0x4000, NAND_BUSWIDTH_16},
+#define SP_OPTIONS NAND_NEED_READRDY
+#define SP_OPTIONS16 (SP_OPTIONS | NAND_BUSWIDTH_16)
- {__NANDSTR("NAND 256MiB 3,3V 8-bit"), 0x71, 512, 256, 0x4000, 0},
+/*
+ * The chip ID list:
+ * name, device ID, page size, chip size in MiB, eraseblock size, options
+ *
+ * If page size and eraseblock size are 0, the sizes are taken from the
+ * extended chip ID.
+ */
+struct nand_flash_dev nand_flash_ids[] = {
+ /*
+ * Some incompatible NAND chips share device ID's and so must be
+ * listed by full ID. We list them first so that we can easily identify
+ * the most specific match.
+ */
+ {__STR("TC58NVG2S0F 4G 3.3V 8-bit"),
+ { .id = {0x98, 0xdc, 0x90, 0x26, 0x76, 0x15, 0x01, 0x08} },
+ SZ_4K, SZ_512, SZ_256K, 0, 8, 224},
+ {__STR("TC58NVG3S0F 8G 3.3V 8-bit"),
+ { .id = {0x98, 0xd3, 0x90, 0x26, 0x76, 0x15, 0x02, 0x08} },
+ SZ_4K, SZ_1K, SZ_256K, 0, 8, 232},
+ {__STR("TC58NVG5D2 32G 3.3V 8-bit"),
+ { .id = {0x98, 0xd7, 0x94, 0x32, 0x76, 0x56, 0x09, 0x00} },
+ SZ_8K, SZ_4K, SZ_1M, 0, 8, 640},
+ {__STR("TC58NVG6D2 64G 3.3V 8-bit"),
+ { .id = {0x98, 0xde, 0x94, 0x82, 0x76, 0x56, 0x04, 0x20} },
+ SZ_8K, SZ_8K, SZ_2M, 0, 8, 640},
+
+ LEGACY_ID_NAND(__STR("NAND 4MiB 5V 8-bit"), 0x6B, 4, SZ_8K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 4MiB 3,3V 8-bit"), 0xE3, 4, SZ_8K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 4MiB 3,3V 8-bit"), 0xE5, 4, SZ_8K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 8MiB 3,3V 8-bit"), 0xD6, 8, SZ_8K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 8MiB 3,3V 8-bit"), 0xE6, 8, SZ_8K, SP_OPTIONS),
+
+ LEGACY_ID_NAND(__STR("NAND 16MiB 1,8V 8-bit"), 0x33, 16, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 16MiB 3,3V 8-bit"), 0x73, 16, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 16MiB 1,8V 16-bit"), 0x43, 16, SZ_16K, SP_OPTIONS16),
+ LEGACY_ID_NAND(__STR("NAND 16MiB 3,3V 16-bit"), 0x53, 16, SZ_16K, SP_OPTIONS16),
+
+ LEGACY_ID_NAND(__STR("NAND 32MiB 1,8V 8-bit"), 0x35, 32, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 32MiB 3,3V 8-bit"), 0x75, 32, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 32MiB 1,8V 16-bit"), 0x45, 32, SZ_16K, SP_OPTIONS16),
+ LEGACY_ID_NAND(__STR("NAND 32MiB 3,3V 16-bit"), 0x55, 32, SZ_16K, SP_OPTIONS16),
+
+ LEGACY_ID_NAND(__STR("NAND 64MiB 1,8V 8-bit"), 0x36, 64, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 64MiB 3,3V 8-bit"), 0x76, 64, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 64MiB 1,8V 16-bit"), 0x46, 64, SZ_16K, SP_OPTIONS16),
+ LEGACY_ID_NAND(__STR("NAND 64MiB 3,3V 16-bit"), 0x56, 64, SZ_16K, SP_OPTIONS16),
+
+ LEGACY_ID_NAND(__STR("NAND 128MiB 1,8V 8-bit"), 0x78, 128, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 128MiB 1,8V 8-bit"), 0x39, 128, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 128MiB 3,3V 8-bit"), 0x79, 128, SZ_16K, SP_OPTIONS),
+ LEGACY_ID_NAND(__STR("NAND 128MiB 1,8V 16-bit"), 0x72, 128, SZ_16K, SP_OPTIONS16),
+ LEGACY_ID_NAND(__STR("NAND 128MiB 1,8V 16-bit"), 0x49, 128, SZ_16K, SP_OPTIONS16),
+ LEGACY_ID_NAND(__STR("NAND 128MiB 3,3V 16-bit"), 0x74, 128, SZ_16K, SP_OPTIONS16),
+ LEGACY_ID_NAND(__STR("NAND 128MiB 3,3V 16-bit"), 0x59, 128, SZ_16K, SP_OPTIONS16),
+
+ LEGACY_ID_NAND(__STR("NAND 256MiB 3,3V 8-bit"), 0x71, 256, SZ_16K, SP_OPTIONS),
/*
- * These are the new chips with large page size. The pagesize and the
- * erasesize is determined from the extended id bytes
+ * These are the new chips with large page size. Their page size and
+ * eraseblock size are determined from the extended ID bytes.
*/
-#define LP_OPTIONS (NAND_SAMSUNG_LP_OPTIONS | NAND_NO_READRDY | NAND_NO_AUTOINCR)
-#define LP_OPTIONS16 (LP_OPTIONS | NAND_BUSWIDTH_16)
- /*512 Megabit */
- {__NANDSTR("NAND 64MiB 1,8V 8-bit"), 0xA2, 0, 64, 0, LP_OPTIONS},
- {__NANDSTR("NAND 64MiB 3,3V 8-bit"), 0xF2, 0, 64, 0, LP_OPTIONS},
- {__NANDSTR("NAND 64MiB 1,8V 16-bit"), 0xB2, 0, 64, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 64MiB 3,3V 16-bit"), 0xC2, 0, 64, 0, LP_OPTIONS16},
+ /* 512 Megabit */
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 1,8V 8-bit"), 0xA2, 64, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 1,8V 8-bit"), 0xA0, 64, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 3,3V 8-bit"), 0xF2, 64, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 3,3V 8-bit"), 0xD0, 64, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 3,3V 8-bit"), 0xF0, 64, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 1,8V 16-bit"), 0xB2, 64, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 1,8V 16-bit"), 0xB0, 64, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 3,3V 16-bit"), 0xC2, 64, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 64MiB 3,3V 16-bit"), 0xC0, 64, LP_OPTIONS16),
/* 1 Gigabit */
- {__NANDSTR("NAND 128MiB 1,8V 8-bit"), 0xA1, 0, 128, 0, LP_OPTIONS},
- {__NANDSTR("NAND 128MiB 3,3V 8-bit"), 0xF1, 0, 128, 0, LP_OPTIONS},
- {__NANDSTR("NAND 128MiB 1,8V 16-bit"), 0xB1, 0, 128, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 128MiB 3,3V 16-bit"), 0xC1, 0, 128, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 128MiB 1,8V 8-bit"), 0xA1, 128, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 128MiB 3,3V 8-bit"), 0xF1, 128, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 128MiB 3,3V 8-bit"), 0xD1, 128, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 128MiB 1,8V 16-bit"), 0xB1, 128, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 128MiB 3,3V 16-bit"), 0xC1, 128, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 128MiB 1,8V 16-bit"), 0xAD, 128, LP_OPTIONS16),
/* 2 Gigabit */
- {__NANDSTR("NAND 256MiB 1,8V 8-bit"), 0xAA, 0, 256, 0, LP_OPTIONS},
- {__NANDSTR("NAND 256MiB 3,3V 8-bit"), 0xDA, 0, 256, 0, LP_OPTIONS},
- {__NANDSTR("NAND 256MiB 1,8V 16-bit"), 0xBA, 0, 256, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 256MiB 3,3V 16-bit"), 0xCA, 0, 256, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 256MiB 1,8V 8-bit"), 0xAA, 256, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 256MiB 3,3V 8-bit"), 0xDA, 256, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 256MiB 1,8V 16-bit"), 0xBA, 256, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 256MiB 3,3V 16-bit"), 0xCA, 256, LP_OPTIONS16),
/* 4 Gigabit */
- {__NANDSTR("NAND 512MiB 1,8V 8-bit"), 0xAC, 0, 512, 0, LP_OPTIONS},
- {__NANDSTR("NAND 512MiB 3,3V 8-bit"), 0xDC, 0, 512, 0, LP_OPTIONS},
- {__NANDSTR("NAND 512MiB 1,8V 16-bit"), 0xBC, 0, 512, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 512MiB 3,3V 16-bit"), 0xCC, 0, 512, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 512MiB 1,8V 8-bit"), 0xAC, 512, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 512MiB 3,3V 8-bit"), 0xDC, 512, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 512MiB 1,8V 16-bit"), 0xBC, 512, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 512MiB 3,3V 16-bit"), 0xCC, 512, LP_OPTIONS16),
/* 8 Gigabit */
- {__NANDSTR("NAND 1GiB 1,8V 8-bit"), 0xA3, 0, 1024, 0, LP_OPTIONS},
- {__NANDSTR("NAND 1GiB 3,3V 8-bit"), 0xD3, 0, 1024, 0, LP_OPTIONS},
- {__NANDSTR("NAND 1GiB 1,8V 16-bit"), 0xB3, 0, 1024, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 1GiB 3,3V 16-bit"), 0xC3, 0, 1024, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 1GiB 1,8V 8-bit"), 0xA3, 1024, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 1GiB 3,3V 8-bit"), 0xD3, 1024, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 1GiB 1,8V 16-bit"), 0xB3, 1024, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 1GiB 3,3V 16-bit"), 0xC3, 1024, LP_OPTIONS16),
/* 16 Gigabit */
- {__NANDSTR("NAND 2GiB 1,8V 8-bit"), 0xA5, 0, 2048, 0, LP_OPTIONS},
- {__NANDSTR("NAND 2GiB 3,3V 8-bit"), 0xD5, 0, 2048, 0, LP_OPTIONS},
- {__NANDSTR("NAND 2GiB 1,8V 16-bit"), 0xB5, 0, 2048, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 2GiB 3,3V 16-bit"), 0xC5, 0, 2048, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 2GiB 1,8V 8-bit"), 0xA5, 2048, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 2GiB 3,3V 8-bit"), 0xD5, 2048, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 2GiB 1,8V 16-bit"), 0xB5, 2048, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 2GiB 3,3V 16-bit"), 0xC5, 2048, LP_OPTIONS16),
/* 32 Gigabit */
- {__NANDSTR("NAND 4GiB 1,8V 8-bit"), 0xA7, 0, 4096, 0, LP_OPTIONS},
- {__NANDSTR("NAND 4GiB 3,3V 8-bit"), 0xD7, 0, 4096, 0, LP_OPTIONS},
- {__NANDSTR("NAND 4GiB 1,8V 16-bit"), 0xB7, 0, 4096, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 4GiB 3,3V 16-bit"), 0xC7, 0, 4096, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 4GiB 1,8V 8-bit"), 0xA7, 4096, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 4GiB 3,3V 8-bit"), 0xD7, 4096, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 4GiB 1,8V 16-bit"), 0xB7, 4096, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 4GiB 3,3V 16-bit"), 0xC7, 4096, LP_OPTIONS16),
/* 64 Gigabit */
- {__NANDSTR("NAND 8GiB 1,8V 8-bit"), 0xAE, 0, 8192, 0, LP_OPTIONS},
- {__NANDSTR("NAND 8GiB 3,3V 8-bit"), 0xDE, 0, 8192, 0, LP_OPTIONS},
- {__NANDSTR("NAND 8GiB 1,8V 16-bit"), 0xBE, 0, 8192, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 8GiB 3,3V 16-bit"), 0xCE, 0, 8192, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 8GiB 1,8V 8-bit"), 0xAE, 8192, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 8GiB 3,3V 8-bit"), 0xDE, 8192, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 8GiB 1,8V 16-bit"), 0xBE, 8192, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 8GiB 3,3V 16-bit"), 0xCE, 8192, LP_OPTIONS16),
/* 128 Gigabit */
- {__NANDSTR("NAND 16GiB 1,8V 8-bit"), 0x1A, 0, 16384, 0, LP_OPTIONS},
- {__NANDSTR("NAND 16GiB 3,3V 8-bit"), 0x3A, 0, 16384, 0, LP_OPTIONS},
- {__NANDSTR("NAND 16GiB 1,8V 16-bit"), 0x2A, 0, 16384, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 16GiB 3,3V 16-bit"), 0x4A, 0, 16384, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 16GiB 1,8V 8-bit"), 0x1A, 16384, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 16GiB 3,3V 8-bit"), 0x3A, 16384, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 16GiB 1,8V 16-bit"), 0x2A, 16384, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 16GiB 3,3V 16-bit"), 0x4A, 16384, LP_OPTIONS16),
/* 256 Gigabit */
- {__NANDSTR("NAND 32GiB 1,8V 8-bit"), 0x1C, 0, 32768, 0, LP_OPTIONS},
- {__NANDSTR("NAND 32GiB 3,3V 8-bit"), 0x3C, 0, 32768, 0, LP_OPTIONS},
- {__NANDSTR("NAND 32GiB 1,8V 16-bit"), 0x2C, 0, 32768, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 32GiB 3,3V 16-bit"), 0x4C, 0, 32768, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 32GiB 1,8V 8-bit"), 0x1C, 32768, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 32GiB 3,3V 8-bit"), 0x3C, 32768, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 32GiB 1,8V 16-bit"), 0x2C, 32768, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 32GiB 3,3V 16-bit"), 0x4C, 32768, LP_OPTIONS16),
/* 512 Gigabit */
- {__NANDSTR("NAND 64GiB 1,8V 8-bit"), 0x1E, 0, 65536, 0, LP_OPTIONS},
- {__NANDSTR("NAND 64GiB 3,3V 8-bit"), 0x3E, 0, 65536, 0, LP_OPTIONS},
- {__NANDSTR("NAND 64GiB 1,8V 16-bit"), 0x2E, 0, 65536, 0, LP_OPTIONS16},
- {__NANDSTR("NAND 64GiB 3,3V 16-bit"), 0x4E, 0, 65536, 0, LP_OPTIONS16},
+ EXTENDED_ID_NAND(__STR("NAND 64GiB 1,8V 8-bit"), 0x1E, 65536, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 64GiB 3,3V 8-bit"), 0x3E, 65536, LP_OPTIONS),
+ EXTENDED_ID_NAND(__STR("NAND 64GiB 1,8V 16-bit"), 0x2E, 65536, LP_OPTIONS16),
+ EXTENDED_ID_NAND(__STR("NAND 64GiB 3,3V 16-bit"), 0x4E, 65536, LP_OPTIONS16),
- /*
- * Renesas AND 1 Gigabit. Those chips do not support extended id and
- * have a strange page/block layout ! The chosen minimum erasesize is
- * 4 * 2 * 2048 = 16384 Byte, as those chips have an array of 4 page
- * planes 1 block = 2 pages, but due to plane arrangement the blocks
- * 0-3 consists of page 0 + 4,1 + 5, 2 + 6, 3 + 7 Anyway JFFS2 would
- * increase the eraseblock size so we chose a combined one which can be
- * erased in one go There are more speed improvements for reads and
- * writes possible, but not implemented now
- */
- {__NANDSTR("AND 128MiB 3,3V 8-bit"), 0x01, 2048, 128, 0x4000,
- NAND_IS_AND | NAND_NO_AUTOINCR |NAND_NO_READRDY | NAND_4PAGE_ARRAY |
- BBT_AUTO_REFRESH
- },
-
- {NULL,}
+ {NULL}
};
-/*
-* Manufacturer ID list
-*/
+/* Manufacturer IDs */
struct nand_manufacturers nand_manuf_ids[] = {
- {NAND_MFR_TOSHIBA, __NANDSTR("Toshiba")},
- {NAND_MFR_SAMSUNG, __NANDSTR("Samsung")},
- {NAND_MFR_FUJITSU, __NANDSTR("Fujitsu")},
- {NAND_MFR_NATIONAL, __NANDSTR("National")},
- {NAND_MFR_RENESAS, __NANDSTR("Renesas")},
- {NAND_MFR_STMICRO, __NANDSTR("ST Micro")},
- {NAND_MFR_HYNIX, __NANDSTR("Hynix")},
- {NAND_MFR_MICRON, __NANDSTR("Micron")},
- {NAND_MFR_AMD, __NANDSTR("AMD/Spansion")},
- {NAND_MFR_MACRONIX, __NANDSTR("Macronix")},
- {NAND_MFR_EON, __NANDSTR("Eon")},
+ {NAND_MFR_TOSHIBA, "Toshiba"},
+ {NAND_MFR_SAMSUNG, "Samsung"},
+ {NAND_MFR_FUJITSU, "Fujitsu"},
+ {NAND_MFR_NATIONAL, "National"},
+ {NAND_MFR_RENESAS, "Renesas"},
+ {NAND_MFR_STMICRO, "ST Micro"},
+ {NAND_MFR_HYNIX, "Hynix"},
+ {NAND_MFR_MICRON, "Micron"},
+ {NAND_MFR_AMD, "AMD/Spansion"},
+ {NAND_MFR_MACRONIX, "Macronix"},
+ {NAND_MFR_EON, "Eon"},
{0x0, "Unknown"}
};
diff --git a/drivers/mtd/nand/nand_imx.c b/drivers/mtd/nand/nand_imx.c
index 91ee494..965b41e 100644
--- a/drivers/mtd/nand/nand_imx.c
+++ b/drivers/mtd/nand/nand_imx.c
@@ -687,23 +687,6 @@ static void copy_spare(struct mtd_info *mtd, int bfrom)
}
/*
- * This function is used by the upper layer to verify the data in NAND Flash
- * with the data in the \b buf.
- *
- * @param mtd MTD structure for the NAND Flash
- * @param buf data to be verified
- * @param len length of the data to be verified
- *
- * @return -EFAULT if error else 0
- *
- */
-static int
-imx_nand_verify_buf(struct mtd_info *mtd, const u_char * buf, int len)
-{
- return -EFAULT;
-}
-
-/*
* This function is used by upper layer for select and deselect of the NAND
* chip
*
@@ -1235,7 +1218,6 @@ static int __init imxnd_probe(struct device_d *dev)
this->read_word = imx_nand_read_word;
this->write_buf = imx_nand_write_buf;
this->read_buf = imx_nand_read_buf;
- this->verify_buf = imx_nand_verify_buf;
if (host->hw_ecc) {
this->ecc.calculate = imx_nand_calculate_ecc;
@@ -1268,7 +1250,7 @@ static int __init imxnd_probe(struct device_d *dev)
}
/* first scan to find the device and get the page size */
- if (nand_scan_ident(mtd, 1)) {
+ if (nand_scan_ident(mtd, 1, NULL)) {
err = -ENXIO;
goto escan;
}
diff --git a/drivers/mtd/nand/nand_mxs.c b/drivers/mtd/nand/nand_mxs.c
index 5d3a488..20c61bb 100644
--- a/drivers/mtd/nand/nand_mxs.c
+++ b/drivers/mtd/nand/nand_mxs.c
@@ -619,7 +619,7 @@ static uint8_t mxs_nand_read_byte(struct mtd_info *mtd)
* Read a page from NAND.
*/
static int mxs_nand_ecc_read_page(struct mtd_info *mtd, struct nand_chip *nand,
- uint8_t *buf)
+ uint8_t *buf, int oob_required, int page)
{
struct mxs_nand_info *nand_info = nand->priv;
struct mxs_dma_desc *d;
@@ -761,13 +761,14 @@ rtn:
/*
* Write a page to NAND.
*/
-static void mxs_nand_ecc_write_page(struct mtd_info *mtd,
- struct nand_chip *nand, const uint8_t *buf)
+static int mxs_nand_ecc_write_page(struct mtd_info *mtd,
+ struct nand_chip *nand, const uint8_t *buf,
+ int oob_required)
{
struct mxs_nand_info *nand_info = nand->priv;
struct mxs_dma_desc *d;
uint32_t channel = MXS_DMA_CHANNEL_AHB_APBH_GPMI0 + nand_info->cur_chip;
- int ret;
+ int ret = 0;
memcpy(nand_info->data_buf, buf, mtd->writesize);
memcpy(nand_info->oob_buf, nand->oob_poi, mtd->oobsize);
@@ -815,6 +816,8 @@ static void mxs_nand_ecc_write_page(struct mtd_info *mtd,
rtn:
mxs_nand_return_dma_descs(nand_info);
+
+ return ret;
}
/*
@@ -933,7 +936,7 @@ static int mxs_nand_hook_block_markbad(struct mtd_info *mtd, loff_t ofs)
* what to do.
*/
static int mxs_nand_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *nand,
- int page, int cmd)
+ int page)
{
struct mxs_nand_info *nand_info = nand->priv;
int column;
@@ -1245,7 +1248,7 @@ static int mxs_nand_probe(struct device_d *dev)
nand->ecc.strength = 8;
/* first scan to find the device and get the page size */
- err = nand_scan_ident(mtd, 1);
+ err = nand_scan_ident(mtd, 1, NULL);
if (err)
goto err2;
diff --git a/drivers/mtd/nand/nand_omap_gpmc.c b/drivers/mtd/nand/nand_omap_gpmc.c
index 9c1f3d7..1b98a4e 100644
--- a/drivers/mtd/nand/nand_omap_gpmc.c
+++ b/drivers/mtd/nand/nand_omap_gpmc.c
@@ -697,7 +697,7 @@ static void omap_write_buf_pref(struct mtd_info *mtd,
* generate dummy eccs for the unprotected oob area.
*/
static int omap_gpmc_read_page_bch_rom_mode(struct mtd_info *mtd,
- struct nand_chip *chip, uint8_t *buf)
+ struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
{
struct gpmc_nand_info *oinfo = chip->priv;
int dev_width = chip->options & NAND_BUSWIDTH_16 ? GPMC_ECC_CONFIG_ECC16B : 0;
@@ -886,7 +886,7 @@ static int omap_gpmc_eccmode_set(struct device_d *dev, struct param_d *param, co
return omap_gpmc_eccmode(oinfo, i);
}
-static int gpmc_set_buswidth(struct mtd_info *mtd, struct nand_chip *chip, int buswidth)
+static int gpmc_set_buswidth(struct nand_chip *chip, int buswidth)
{
struct gpmc_nand_info *oinfo = chip->priv;
@@ -1007,8 +1007,6 @@ static int gpmc_nand_probe(struct device_d *pdev)
nand->options |= NAND_OWN_BUFFERS;
nand->buffers = xzalloc(sizeof(*nand->buffers));
- nand->set_buswidth = gpmc_set_buswidth;
-
/* State my controller */
nand->controller = &oinfo->controller;
@@ -1031,11 +1029,13 @@ static int gpmc_nand_probe(struct device_d *pdev)
mdelay(1);
/* first scan to find the device and get the page size */
- if (nand_scan_ident(minfo, 1)) {
+ if (nand_scan_ident(minfo, 1, NULL)) {
err = -ENXIO;
goto out_release_mem;
}
+ gpmc_set_buswidth(nand, nand->options & NAND_BUSWIDTH_16);
+
if (nand->options & NAND_BUSWIDTH_16) {
lsp = &ecc_sp_x16;
llp = &ecc_lp_x16;
diff --git a/drivers/mtd/nand/nand_swecc.c b/drivers/mtd/nand/nand_swecc.c
deleted file mode 100644
index 35f8469..0000000
--- a/drivers/mtd/nand/nand_swecc.c
+++ /dev/null
@@ -1,95 +0,0 @@
-#include <common.h>
-#include <errno.h>
-#include <clock.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/err.h>
-#include <linux/mtd/nand_ecc.h>
-#include <asm/byteorder.h>
-#include <io.h>
-#include <malloc.h>
-
-#include "nand.h"
-
-/**
- * nand_read_page_swecc - [REPLACABLE] software ecc based page read function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: buffer to store read data
- */
-static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf)
-{
- int i, eccsize = chip->ecc.size;
- int eccbytes = chip->ecc.bytes;
- int eccsteps = chip->ecc.steps;
- uint8_t *p = buf;
- uint8_t *ecc_calc = chip->buffers->ecccalc;
- uint8_t *ecc_code = chip->buffers->ecccode;
- uint32_t *eccpos = chip->ecc.layout->eccpos;
-
- chip->ecc.read_page_raw(mtd, chip, buf);
-
- for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
- chip->ecc.calculate(mtd, p, &ecc_calc[i]);
-
- for (i = 0; i < chip->ecc.total; i++)
- ecc_code[i] = chip->oob_poi[eccpos[i]];
-
- eccsteps = chip->ecc.steps;
- p = buf;
-
- for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
- int stat;
-
- stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
- if (stat < 0)
- mtd->ecc_stats.failed++;
- else
- mtd->ecc_stats.corrected += stat;
- }
- return 0;
-}
-
-/**
- * nand_write_page_swecc - [REPLACABLE] software ecc based page write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: data buffer
- */
-#ifdef CONFIG_MTD_WRITE
-static void nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf)
-{
- int i, eccsize = chip->ecc.size;
- int eccbytes = chip->ecc.bytes;
- int eccsteps = chip->ecc.steps;
- uint8_t *ecc_calc = chip->buffers->ecccalc;
- const uint8_t *p = buf;
- uint32_t *eccpos = chip->ecc.layout->eccpos;
-
- /* Software ecc calculation */
- for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
- chip->ecc.calculate(mtd, p, &ecc_calc[i]);
-
- for (i = 0; i < chip->ecc.total; i++)
- chip->oob_poi[eccpos[i]] = ecc_calc[i];
-
- chip->ecc.write_page_raw(mtd, chip, buf);
-}
-#endif
-
-void nand_init_ecc_soft(struct nand_chip *chip)
-{
- chip->ecc.calculate = nand_calculate_ecc;
- chip->ecc.correct = nand_correct_data;
- chip->ecc.read_page = nand_read_page_swecc;
- chip->ecc.read_oob = nand_read_oob_std;
-#ifdef CONFIG_MTD_WRITE
- chip->ecc.write_page = nand_write_page_swecc;
- chip->ecc.write_oob = nand_write_oob_std;
-#endif
- chip->ecc.size = 256;
- chip->ecc.bytes = 3;
- chip->ecc.strength = 1;
-}
diff --git a/drivers/mtd/nand/nand_write.c b/drivers/mtd/nand/nand_write.c
deleted file mode 100644
index 3d8003e..0000000
--- a/drivers/mtd/nand/nand_write.c
+++ /dev/null
@@ -1,788 +0,0 @@
-#define pr_fmt(fmt) "nand: " fmt
-
-#include <common.h>
-#include <errno.h>
-#include <clock.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/err.h>
-#include <linux/mtd/nand_ecc.h>
-#include <asm/byteorder.h>
-#include <io.h>
-#include <malloc.h>
-#include <module.h>
-
-#include "nand.h"
-
-static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
- struct mtd_oob_ops *ops);
-
-/**
- * nand_write_buf - [DEFAULT] write buffer to chip
- * @mtd: MTD device structure
- * @buf: data buffer
- * @len: number of bytes to write
- *
- * Default write function for 8bit buswith
- */
-void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
-{
- int i;
- struct nand_chip *chip = mtd->priv;
-
- for (i = 0; i < len; i++)
- writeb(buf[i], chip->IO_ADDR_W);
-}
-
-/**
- * nand_write_buf16 - [DEFAULT] write buffer to chip
- * @mtd: MTD device structure
- * @buf: data buffer
- * @len: number of bytes to write
- *
- * Default write function for 16bit buswith
- */
-void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
-{
- int i;
- struct nand_chip *chip = mtd->priv;
- u16 *p = (u16 *) buf;
- len >>= 1;
-
- for (i = 0; i < len; i++)
- writew(p[i], chip->IO_ADDR_W);
-
-}
-
-/**
- * nand_default_block_markbad - [DEFAULT] mark a block bad
- * @mtd: MTD device structure
- * @ofs: offset from device start
- *
- * This is the default implementation, which can be overridden by a hardware
- * specific driver. We try operations in the following order, according to our
- * bbt_options (NAND_BBT_NO_OOB_BBM and NAND_BBT_USE_FLASH):
- * (1) erase the affected block, to allow OOB marker to be written cleanly
- * (2) update in-memory BBT
- * (3) write bad block marker to OOB area of affected block
- * (4) update flash-based BBT
- * Note that we retain the first error encountered in (3) or (4), finish the
- * procedures, and dump the error in the end.
-*/
-int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
-{
- struct nand_chip *chip = mtd->priv;
- uint8_t buf[2] = { 0, 0 };
- int block, res, ret = 0, i = 0;
- int write_oob = 1; /* Currently we do not have NAND_BBT_NO_OOB_BBM */
-
- if (write_oob) {
- struct erase_info einfo;
-
- /* Attempt erase before marking OOB */
- memset(&einfo, 0, sizeof(einfo));
- einfo.mtd = mtd;
- einfo.addr = ofs;
- einfo.len = 1 << chip->phys_erase_shift;
- nand_erase_nand(mtd, &einfo, 0);
- }
-
- /* Get block number */
- block = (int)(ofs >> chip->bbt_erase_shift);
- /* Mark block bad in memory-based BBT */
- if (chip->bbt)
- chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
-
- /* Write bad block marker to OOB */
- if (write_oob) {
- struct mtd_oob_ops ops;
- loff_t wr_ofs = ofs;
-
- ops.datbuf = NULL;
- ops.oobbuf = buf;
- ops.ooboffs = chip->badblockpos;
- if (chip->options & NAND_BUSWIDTH_16) {
- ops.ooboffs &= ~0x01;
- ops.len = ops.ooblen = 2;
- } else {
- ops.len = ops.ooblen = 1;
- }
- ops.mode = MTD_OPS_PLACE_OOB;
-
- /* Write to first/last page(s) if necessary */
- if (chip->options & NAND_BBT_LASTBLOCK)
- wr_ofs += mtd->erasesize - mtd->writesize;
- do {
- res = nand_do_write_oob(mtd, wr_ofs, &ops);
- if (!ret)
- ret = res;
-
- i++;
- wr_ofs += mtd->writesize;
- } while ((chip->options & NAND_BBT_SCAN2NDPAGE) && i < 2);
- }
-
- /* Update flash-based bad block table */
- if (chip->options & NAND_BBT_USE_FLASH) {
- res = nand_update_bbt(mtd, ofs);
- if (!ret)
- ret = res;
- }
-
- if (!ret)
- mtd->ecc_stats.badblocks++;
-
- return ret;
-}
-
-/**
- * nand_check_wp - [GENERIC] check if the chip is write protected
- * @mtd: MTD device structure
- * Check, if the device is write protected
- *
- * The function expects, that the device is already selected
- */
-static int nand_check_wp(struct mtd_info *mtd)
-{
- struct nand_chip *chip = mtd->priv;
- /* Check the WP bit */
- chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
- return (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1;
-}
-
-/**
- * nand_write_oob_std - [REPLACABLE] the most common OOB data write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @page: page number to write
- */
-int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip,
- int page)
-{
- int status = 0;
- const uint8_t *buf = chip->oob_poi;
- int length = mtd->oobsize;
-
- chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page);
- chip->write_buf(mtd, buf, length);
- /* Send command to program the OOB data */
- chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
-
- status = chip->waitfunc(mtd, chip);
-
- return status & NAND_STATUS_FAIL ? -EIO : 0;
-}
-
-/**
- * nand_write_page_raw - [Intern] raw page write function
- * @mtd: mtd info structure
- * @chip: nand chip info structure
- * @buf: data buffer
- */
-void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf)
-{
- chip->write_buf(mtd, buf, mtd->writesize);
- chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
-}
-
-/**
- * nand_write_page - [REPLACEABLE] write one page
- * @mtd: MTD device structure
- * @chip: NAND chip descriptor
- * @buf: the data to write
- * @page: page number to write
- * @cached: cached programming
- * @raw: use _raw version of write_page
- */
-int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf, int page, int cached, int raw)
-{
- int status;
-
- chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page);
-
- if (unlikely(raw))
- chip->ecc.write_page_raw(mtd, chip, buf);
- else
- chip->ecc.write_page(mtd, chip, buf);
-
- /*
- * Cached progamming disabled for now, Not sure if its worth the
- * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s)
- */
- cached = 0;
-
- if (!cached || !(chip->options & NAND_CACHEPRG)) {
-
- chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
- status = chip->waitfunc(mtd, chip);
- /*
- * See if operation failed and additional status checks are
- * available
- */
- if ((status & NAND_STATUS_FAIL) && (chip->errstat))
- status = chip->errstat(mtd, chip, FL_WRITING, status,
- page);
-
- if (status & NAND_STATUS_FAIL) {
- return -EIO;
- }
- } else {
- chip->cmdfunc(mtd, NAND_CMD_CACHEDPROG, -1, -1);
- status = chip->waitfunc(mtd, chip);
- }
-
-#ifdef CONFIG_MTD_NAND_VERIFY_WRITE
- /* Send command to read back the data */
- chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
-
- if (chip->verify_buf(mtd, buf, mtd->writesize))
- return -EIO;
-#endif
- return 0;
-}
-
-/**
- * nand_fill_oob - [Internal] Transfer client buffer to oob
- * @chip: nand chip structure
- * @oob: oob data buffer
- * @ops: oob ops structure
- */
-static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob,
- struct mtd_oob_ops *ops)
-{
- size_t len = ops->ooblen;
-
- switch(ops->mode) {
-
- case MTD_OPS_PLACE_OOB:
- case MTD_OPS_RAW:
- memcpy(chip->oob_poi + ops->ooboffs, oob, len);
- return oob + len;
-
- case MTD_OPS_AUTO_OOB: {
- struct nand_oobfree *free = chip->ecc.layout->oobfree;
- uint32_t boffs = 0, woffs = ops->ooboffs;
- size_t bytes = 0;
-
- for(; free->length && len; free++, len -= bytes) {
- /* Write request not from offset 0 ? */
- if (unlikely(woffs)) {
- if (woffs >= free->length) {
- woffs -= free->length;
- continue;
- }
- boffs = free->offset + woffs;
- bytes = min_t(size_t, len,
- (free->length - woffs));
- woffs = 0;
- } else {
- bytes = min_t(size_t, len, free->length);
- boffs = free->offset;
- }
- memcpy(chip->oob_poi + boffs, oob, bytes);
- oob += bytes;
- }
- return oob;
- }
- default:
- BUG();
- }
- return NULL;
-}
-
-#define NOTALIGNED(x) (x & (chip->subpagesize - 1)) != 0
-
-/**
- * nand_do_write_ops - [Internal] NAND write with ECC
- * @mtd: MTD device structure
- * @to: offset to write to
- * @ops: oob operations description structure
- *
- * NAND write with ECC
- */
-int nand_do_write_ops(struct mtd_info *mtd, loff_t to,
- struct mtd_oob_ops *ops)
-{
- int chipnr, realpage, page, blockmask, column;
- struct nand_chip *chip = mtd->priv;
- uint32_t writelen = ops->len;
- uint8_t *oob = ops->oobbuf;
- uint8_t *buf = ops->datbuf;
- int ret = 0, subpage;
-
- ops->retlen = 0;
- if (!writelen)
- return 0;
-
- column = to & (mtd->writesize - 1);
- subpage = column || (writelen & (mtd->writesize - 1));
-
- if (subpage && oob)
- return -EINVAL;
-
- chipnr = (int)(to >> chip->chip_shift);
- chip->select_chip(mtd, chipnr);
-
- /* Check, if it is write protected */
- if (nand_check_wp(mtd)) {
- return -EIO;
- }
-
- realpage = (int)(to >> chip->page_shift);
- page = realpage & chip->pagemask;
- blockmask = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1;
-
- /* Invalidate the page cache, when we write to the cached page */
- if (to <= (chip->pagebuf << chip->page_shift) &&
- (chip->pagebuf << chip->page_shift) < (to + ops->len))
- chip->pagebuf = -1;
-
- while(1) {
- int bytes = mtd->writesize;
- int cached = writelen > bytes && page != blockmask;
- uint8_t *wbuf = buf;
-
- /* Partial page write ? */
- if (unlikely(column || writelen < (mtd->writesize - 1))) {
- cached = 0;
- bytes = min_t(int, bytes - column, (int) writelen);
- chip->pagebuf = -1;
- memset(chip->buffers->databuf, 0xff, mtd->writesize);
- memcpy(&chip->buffers->databuf[column], buf, bytes);
- wbuf = chip->buffers->databuf;
- }
-
- if (unlikely(oob)) {
- oob = nand_fill_oob(chip, oob, ops);
- } else {
- /* We still need to erase leftover OOB data */
- memset(chip->oob_poi, 0xff, mtd->oobsize);
- }
-
- if (oob || !mtd_all_ff(wbuf, mtd->writesize)) {
- ret = chip->write_page(mtd, chip, wbuf, page, cached,
- (ops->mode == MTD_OPS_RAW));
- if (ret)
- break;
- }
-
- writelen -= bytes;
- if (!writelen)
- break;
-
- column = 0;
- buf += bytes;
- realpage++;
-
- page = realpage & chip->pagemask;
- /* Check, if we cross a chip boundary */
- if (!page) {
- chipnr++;
- chip->select_chip(mtd, -1);
- chip->select_chip(mtd, chipnr);
- }
- }
-
- ops->retlen = ops->len - writelen;
- if (unlikely(oob))
- ops->oobretlen = ops->ooblen;
- return ret;
-}
-
-/**
- * nand_write - [MTD Interface] NAND write with ECC
- * @mtd: MTD device structure
- * @to: offset to write to
- * @len: number of bytes to write
- * @retlen: pointer to variable to store the number of written bytes
- * @buf: the data to write
- *
- * NAND write with ECC
- */
-int nand_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const uint8_t *buf)
-{
- struct nand_chip *chip = mtd->priv;
- int ret;
-
- /* Do not allow reads past end of device */
- if ((to + len) > mtd->size)
- return -EINVAL;
- if (!len)
- return 0;
-
- chip->ops.len = len;
- chip->ops.datbuf = (uint8_t *)buf;
- chip->ops.oobbuf = NULL;
-
- ret = nand_do_write_ops(mtd, to, &chip->ops);
-
- *retlen = chip->ops.retlen;
-
- return ret;
-}
-
-/**
- * nand_do_write_oob - [MTD Interface] NAND write out-of-band
- * @mtd: MTD device structure
- * @to: offset to write to
- * @ops: oob operation description structure
- *
- * NAND write out-of-band
- */
-static int nand_do_write_oob(struct mtd_info *mtd, loff_t to,
- struct mtd_oob_ops *ops)
-{
- int chipnr, page, status, len;
- struct nand_chip *chip = mtd->priv;
-
- MTD_DEBUG(MTD_DEBUG_LEVEL3, "nand_write_oob: to = 0x%08x, len = %i\n",
- (unsigned int)to, (int)ops->ooblen);
-
- if (ops->mode == MTD_OPS_AUTO_OOB)
- len = chip->ecc.layout->oobavail;
- else
- len = mtd->oobsize;
-
- /* Do not allow write past end of page */
- if ((ops->ooboffs + ops->ooblen) > len) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_write_oob: "
- "Attempt to write past end of page\n");
- return -EINVAL;
- }
-
- if (unlikely(ops->ooboffs >= len)) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt to start write outside oob\n");
- return -EINVAL;
- }
-
- /* Do not allow reads past end of device */
- if (unlikely(to >= mtd->size ||
- ops->ooboffs + ops->ooblen >
- ((mtd->size >> chip->page_shift) -
- (to >> chip->page_shift)) * len)) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt write beyond end of device\n");
- return -EINVAL;
- }
-
- chipnr = (int)(to >> chip->chip_shift);
- chip->select_chip(mtd, chipnr);
-
- /* Shift to get page */
- page = (int)(to >> chip->page_shift);
-
- /*
- * Reset the chip. Some chips (like the Toshiba TC5832DC found in one
- * of my DiskOnChip 2000 test units) will clear the whole data page too
- * if we don't do this. I have no clue why, but I seem to have 'fixed'
- * it in the doc2000 driver in August 1999. dwmw2.
- */
- chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
-
- /* Check, if it is write protected */
- if (nand_check_wp(mtd))
- return -EROFS;
-
- /* Invalidate the page cache, if we write to the cached page */
- if (page == chip->pagebuf)
- chip->pagebuf = -1;
-
- memset(chip->oob_poi, 0xff, mtd->oobsize);
- nand_fill_oob(chip, ops->oobbuf, ops);
- status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask);
- memset(chip->oob_poi, 0xff, mtd->oobsize);
-
- if (status)
- return status;
-
- ops->oobretlen = ops->ooblen;
-
- return 0;
-}
-
-/**
- * nand_write_oob - [MTD Interface] NAND write data and/or out-of-band
- * @mtd: MTD device structure
- * @to: offset to write to
- * @ops: oob operation description structure
- */
-int nand_write_oob(struct mtd_info *mtd, loff_t to,
- struct mtd_oob_ops *ops)
-{
- int ret = -ENOSYS;
-
- ops->retlen = 0;
-
- /* Do not allow writes past end of device */
- if (ops->datbuf && (to + ops->len) > mtd->size) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt read beyond end of device\n");
- return -EINVAL;
- }
-
- switch(ops->mode) {
- case MTD_OPS_PLACE_OOB:
- case MTD_OPS_AUTO_OOB:
- case MTD_OPS_RAW:
- break;
-
- default:
- goto out;
- }
-
- if (!ops->datbuf)
- ret = nand_do_write_oob(mtd, to, ops);
- else
- ret = nand_do_write_ops(mtd, to, ops);
-
- out:
- return ret;
-}
-
-/**
- * single_erease_cmd - [GENERIC] NAND standard block erase command function
- * @mtd: MTD device structure
- * @page: the page address of the block which will be erased
- *
- * Standard erase command for NAND chips
- */
-void single_erase_cmd(struct mtd_info *mtd, int page)
-{
- struct nand_chip *chip = mtd->priv;
- /* Send commands to erase a block */
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page);
- chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
-}
-
-/**
- * multi_erease_cmd - [GENERIC] AND specific block erase command function
- * @mtd: MTD device structure
- * @page: the page address of the block which will be erased
- *
- * AND multi block erase command function
- * Erase 4 consecutive blocks
- */
-void multi_erase_cmd(struct mtd_info *mtd, int page)
-{
- struct nand_chip *chip = mtd->priv;
- /* Send commands to erase a block */
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++);
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++);
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++);
- chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page);
- chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1);
-}
-
-/**
- * nand_erase - [MTD Interface] erase block(s)
- * @mtd: MTD device structure
- * @instr: erase instruction
- *
- * Erase one ore more blocks
- */
-int nand_erase(struct mtd_info *mtd, struct erase_info *instr)
-{
- return nand_erase_nand(mtd, instr, 0);
-}
-
-#define BBT_PAGE_MASK 0xffffff3f
-/**
- * nand_erase_nand - [Internal] erase block(s)
- * @mtd: MTD device structure
- * @instr: erase instruction
- * @allowbbt: allow erasing the bbt area
- *
- * Erase one ore more blocks
- */
-int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
- int allowbbt)
-{
- int page, len, status, pages_per_block, ret, chipnr;
- struct nand_chip *chip = mtd->priv;
- int rewrite_bbt[NAND_MAX_CHIPS]={0};
- unsigned int bbt_masked_page = 0xffffffff;
-
- MTD_DEBUG(MTD_DEBUG_LEVEL3, "nand_erase: start = 0x%08x, len = %i\n",
- (unsigned int)instr->addr, (unsigned int)instr->len);
-
- /* Start address must align on block boundary */
- if (instr->addr & ((1 << chip->phys_erase_shift) - 1)) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: Unaligned address\n");
- return -EINVAL;
- }
-
- /* Length must align on block boundary */
- if (instr->len & ((1 << chip->phys_erase_shift) - 1)) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: "
- "Length not block aligned\n");
- return -EINVAL;
- }
-
- /* Do not allow erase past end of device */
- if ((instr->len + instr->addr) > mtd->size) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: "
- "Erase past end of device\n");
- return -EINVAL;
- }
-
- instr->fail_addr = 0xffffffff;
-
- /* Shift to get first page */
- page = (int)(instr->addr >> chip->page_shift);
- chipnr = (int)(instr->addr >> chip->chip_shift);
-
- /* Calculate pages in each block */
- pages_per_block = 1 << (chip->phys_erase_shift - chip->page_shift);
-
- /* Select the NAND device */
- chip->select_chip(mtd, chipnr);
-
- /* Check, if it is write protected */
- if (nand_check_wp(mtd)) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: "
- "Device is write protected!!!\n");
- instr->state = MTD_ERASE_FAILED;
- goto erase_exit;
- }
-
- /*
- * If BBT requires refresh, set the BBT page mask to see if the BBT
- * should be rewritten. Otherwise the mask is set to 0xffffffff which
- * can not be matched. This is also done when the bbt is actually
- * erased to avoid recusrsive updates
- */
- if (chip->options & BBT_AUTO_REFRESH && !allowbbt)
- bbt_masked_page = chip->bbt_td->pages[chipnr] & BBT_PAGE_MASK;
-
- /* Loop through the pages */
- len = instr->len;
-
- instr->state = MTD_ERASING;
-
- while (len) {
- /*
- * heck if we have a bad block, we do not erase bad blocks !
- */
- if (!mtd->allow_erasebad &&
- nand_block_checkbad(mtd, ((loff_t) page) <<
- chip->page_shift, 0, allowbbt)) {
- pr_warn("nand_erase: attempt to erase a "
- "bad block at page 0x%08x\n", page);
- instr->state = MTD_ERASE_FAILED;
- goto erase_exit;
- }
-
- /*
- * Invalidate the page cache, if we erase the block which
- * contains the current cached page
- */
- if (page <= chip->pagebuf && chip->pagebuf <
- (page + pages_per_block))
- chip->pagebuf = -1;
-
- chip->erase_cmd(mtd, page & chip->pagemask);
-
- status = chip->waitfunc(mtd, chip);
-
- /*
- * See if operation failed and additional status checks are
- * available
- */
- if ((status & NAND_STATUS_FAIL) && (chip->errstat))
- status = chip->errstat(mtd, chip, FL_ERASING,
- status, page);
-
- /* See if block erase succeeded */
- if (status & NAND_STATUS_FAIL) {
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: "
- "Failed erase, page 0x%08x\n", page);
- instr->state = MTD_ERASE_FAILED;
- instr->fail_addr = (page << chip->page_shift);
- goto erase_exit;
- }
-
- /*
- * If BBT requires refresh, set the BBT rewrite flag to the
- * page being erased
- */
- if (bbt_masked_page != 0xffffffff &&
- (page & BBT_PAGE_MASK) == bbt_masked_page)
- rewrite_bbt[chipnr] = (page << chip->page_shift);
-
- /* Increment page address and decrement length */
- len -= (1 << chip->phys_erase_shift);
- page += pages_per_block;
-
- /* Check, if we cross a chip boundary */
- if (len && !(page & chip->pagemask)) {
- chipnr++;
- chip->select_chip(mtd, -1);
- chip->select_chip(mtd, chipnr);
-
- /*
- * If BBT requires refresh and BBT-PERCHIP, set the BBT
- * page mask to see if this BBT should be rewritten
- */
- if (bbt_masked_page != 0xffffffff &&
- (chip->bbt_td->options & NAND_BBT_PERCHIP))
- bbt_masked_page = chip->bbt_td->pages[chipnr] &
- BBT_PAGE_MASK;
- }
- }
- instr->state = MTD_ERASE_DONE;
-
- erase_exit:
-
- ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO;
-
- /* Do call back function */
- if (!ret)
- mtd_erase_callback(instr);
-
- /*
- * If BBT requires refresh and erase was successful, rewrite any
- * selected bad block tables
- */
- if (bbt_masked_page == 0xffffffff || ret)
- return ret;
-
- if (!IS_ENABLED(CONFIG_NAND_BBT))
- return ret;
-
- for (chipnr = 0; chipnr < chip->numchips; chipnr++) {
- if (!rewrite_bbt[chipnr])
- continue;
- /* update the BBT for chip */
- MTD_DEBUG(MTD_DEBUG_LEVEL0, "nand_erase_nand: nand_update_bbt "
- "(%d:0x%0x 0x%0x)\n", chipnr, rewrite_bbt[chipnr],
- chip->bbt_td->pages[chipnr]);
- nand_update_bbt(mtd, rewrite_bbt[chipnr]);
- }
-
- /* Return more or less happy */
- return ret;
-}
-
-/**
- * nand_block_markbad - [MTD Interface] Mark block at the given offset as bad
- * @mtd: MTD device structure
- * @ofs: offset relative to mtd start
- */
-int nand_block_markbad(struct mtd_info *mtd, loff_t ofs)
-{
- struct nand_chip *chip = mtd->priv;
- int ret;
-
- if ((ret = nand_block_isbad(mtd, ofs))) {
- /* If it was bad already, return success and do nothing. */
- if (ret > 0)
- return 0;
- return ret;
- }
-
- return chip->block_markbad(mtd, ofs);
-}
diff --git a/include/asm-generic/errno.h b/include/asm-generic/errno.h
index 134a8fc..bbf493c 100644
--- a/include/asm-generic/errno.h
+++ b/include/asm-generic/errno.h
@@ -133,6 +133,8 @@
#define ERESTARTNOHAND 514 /* restart if no handler.. */
#define ENOIOCTLCMD 515 /* No ioctl command */
-#define _LAST_ERRNO 515
+#define ENOTSUPP 524 /* Operation is not supported */
+
+#define _LAST_ERRNO 524
#endif
diff --git a/include/linux/mtd/bbm.h b/include/linux/mtd/bbm.h
index 87ec6a3..211ff67 100644
--- a/include/linux/mtd/bbm.h
+++ b/include/linux/mtd/bbm.h
@@ -103,7 +103,6 @@ struct nand_bbt_descr {
#define NAND_BBT_SCAN2NDPAGE 0x00008000
/* Search good / bad pattern on the last page of the eraseblock */
#define NAND_BBT_SCANLASTPAGE 0x00010000
-
/*
* Use a flash based bad block table. By default, OOB identifier is saved in
* OOB area. This option is passed to the default bad block table function.
@@ -130,4 +129,48 @@ struct nand_bbt_descr {
/* The maximum number of blocks to scan for a bbt */
#define NAND_BBT_SCAN_MAXBLOCKS 4
+/*
+ * Constants for oob configuration
+ */
+#define NAND_SMALL_BADBLOCK_POS 5
+#define NAND_LARGE_BADBLOCK_POS 0
+#define ONENAND_BADBLOCK_POS 0
+
+/*
+ * Bad block scanning errors
+ */
+#define ONENAND_BBT_READ_ERROR 1
+#define ONENAND_BBT_READ_ECC_ERROR 2
+#define ONENAND_BBT_READ_FATAL_ERROR 4
+
+/**
+ * struct bbm_info - [GENERIC] Bad Block Table data structure
+ * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry
+ * @badblockpos: [INTERN] position of the bad block marker in the oob area
+ * @options: options for this descriptor
+ * @bbt: [INTERN] bad block table pointer
+ * @isbad_bbt: function to determine if a block is bad
+ * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for
+ * initial bad block scan
+ * @priv: [OPTIONAL] pointer to private bbm date
+ */
+struct bbm_info {
+ int bbt_erase_shift;
+ int badblockpos;
+ int options;
+
+ uint8_t *bbt;
+
+ int (*isbad_bbt)(struct mtd_info *mtd, loff_t ofs, int allowbbt);
+
+ /* TODO Add more NAND specific fileds */
+ struct nand_bbt_descr *badblock_pattern;
+
+ void *priv;
+};
+
+/* OneNAND BBT interface */
+extern int onenand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd);
+extern int onenand_default_bbt(struct mtd_info *mtd);
+
#endif /* __LINUX_MTD_BBM_H */
diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h
index 040e50d..4949460 100644
--- a/include/linux/mtd/mtd.h
+++ b/include/linux/mtd/mtd.h
@@ -101,6 +101,17 @@ struct mtd_info {
*/
u_int32_t writesize;
+ /*
+ * Size of the write buffer used by the MTD. MTD devices having a write
+ * buffer can write multiple writesize chunks at a time. E.g. while
+ * writing 4 * writesize bytes to a device with 2 * writesize bytes
+ * buffer the MTD driver can (but doesn't have to) do 2 writesize
+ * operations, but not 4. Currently, all NANDs have writebufsize
+ * equivalent to writesize (NAND page size). Some NOR flashes do have
+ * writebufsize greater than writesize.
+ */
+ uint32_t writebufsize;
+
u_int32_t oobsize; // Amount of OOB data per block (e.g. 16)
u_int32_t oobavail; // Available OOB bytes per block
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index e5cfed9..74ea0b4 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -1,11 +1,9 @@
/*
* linux/include/linux/mtd/nand.h
*
- * Copyright (c) 2000 David Woodhouse <dwmw2@infradead.org>
- * Steven J. Hill <sjhill@realitydiluted.com>
- * Thomas Gleixner <tglx@linutronix.de>
- *
- * $Id: nand.h,v 1.74 2005/09/15 13:58:50 vwool Exp $
+ * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org>
+ * Steven J. Hill <sjhill@realitydiluted.com>
+ * Thomas Gleixner <tglx@linutronix.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -20,34 +18,43 @@
#ifndef __LINUX_MTD_NAND_H
#define __LINUX_MTD_NAND_H
-#ifndef DOXYGEN_SHOULD_SKIP_THIS
-
#include <linux/mtd/mtd.h>
-
-/* The maximum number of NAND chips in an array */
-#define NAND_MAX_CHIPS 8
-
+#include <linux/mtd/flashchip.h>
#include <linux/mtd/bbm.h>
struct mtd_info;
+struct nand_flash_dev;
/* Scan and identify a NAND device */
-extern int nand_scan (struct mtd_info *mtd, int max_chips);
-/* Separate phases of nand_scan(), allowing board driver to intervene
- * and override command or ECC setup according to flash type */
-extern int nand_scan_ident(struct mtd_info *mtd, int max_chips);
+extern int nand_scan(struct mtd_info *mtd, int max_chips);
+/*
+ * Separate phases of nand_scan(), allowing board driver to intervene
+ * and override command or ECC setup according to flash type.
+ */
+extern int nand_scan_ident(struct mtd_info *mtd, int max_chips,
+ struct nand_flash_dev *table);
extern int nand_scan_tail(struct mtd_info *mtd);
/* Free resources held by the NAND device */
-extern void nand_release (struct mtd_info *mtd);
+extern void nand_release(struct mtd_info *mtd);
/* Internal helper for board drivers which need to override command function */
extern void nand_wait_ready(struct mtd_info *mtd);
-/* This constant declares the max. oobsize / page, which
+/* locks all blocks present in the device */
+extern int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
+
+/* unlocks specified locked blocks */
+extern int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
+
+/* The maximum number of NAND chips in an array */
+#define NAND_MAX_CHIPS 8
+
+/*
+ * This constant declares the max. oobsize / page, which
* is supported now. If you add a chip with bigger oobsize/page
* adjust this accordingly.
*/
-#define NAND_MAX_OOBSIZE 576
+#define NAND_MAX_OOBSIZE 640
#define NAND_MAX_PAGESIZE 8192
/*
@@ -77,38 +84,24 @@ extern void nand_wait_ready(struct mtd_info *mtd);
#define NAND_CMD_READOOB 0x50
#define NAND_CMD_ERASE1 0x60
#define NAND_CMD_STATUS 0x70
-#define NAND_CMD_STATUS_MULTI 0x71
#define NAND_CMD_SEQIN 0x80
#define NAND_CMD_RNDIN 0x85
#define NAND_CMD_READID 0x90
#define NAND_CMD_ERASE2 0xd0
#define NAND_CMD_PARAM 0xec
+#define NAND_CMD_GET_FEATURES 0xee
+#define NAND_CMD_SET_FEATURES 0xef
#define NAND_CMD_RESET 0xff
+#define NAND_CMD_LOCK 0x2a
+#define NAND_CMD_UNLOCK1 0x23
+#define NAND_CMD_UNLOCK2 0x24
+
/* Extended commands for large page devices */
#define NAND_CMD_READSTART 0x30
#define NAND_CMD_RNDOUTSTART 0xE0
#define NAND_CMD_CACHEDPROG 0x15
-/* Extended commands for AG-AND device */
-/*
- * Note: the command for NAND_CMD_DEPLETE1 is really 0x00 but
- * there is no way to distinguish that from NAND_CMD_READ0
- * until the remaining sequence of commands has been completed
- * so add a high order bit and mask it off in the command.
- */
-#define NAND_CMD_DEPLETE1 0x100
-#define NAND_CMD_DEPLETE2 0x38
-#define NAND_CMD_STATUS_MULTI 0x71
-#define NAND_CMD_STATUS_ERROR 0x72
-/* multi-bank error status (banks 0-3) */
-#define NAND_CMD_STATUS_ERROR0 0x73
-#define NAND_CMD_STATUS_ERROR1 0x74
-#define NAND_CMD_STATUS_ERROR2 0x75
-#define NAND_CMD_STATUS_ERROR3 0x76
-#define NAND_CMD_STATUS_RESET 0x7f
-#define NAND_CMD_STATUS_CLEAR 0xff
-
#define NAND_CMD_NONE -1
/* Status bits */
@@ -126,6 +119,8 @@ typedef enum {
NAND_ECC_SOFT,
NAND_ECC_HW,
NAND_ECC_HW_SYNDROME,
+ NAND_ECC_HW_OOB_FIRST,
+ NAND_ECC_SOFT_BCH,
} nand_ecc_modes_t;
/*
@@ -135,65 +130,65 @@ typedef enum {
#define NAND_ECC_READ 0
/* Reset Hardware ECC for write */
#define NAND_ECC_WRITE 1
-/* Enable Hardware ECC before syndrom is read back from flash */
+/* Enable Hardware ECC before syndrome is read back from flash */
#define NAND_ECC_READSYN 2
/* Bit mask for flags passed to do_nand_read_ecc */
#define NAND_GET_DEVICE 0x80
-/* Option constants for bizarre disfunctionality and real
-* features
-*/
-/* Chip can not auto increment pages */
-#define NAND_NO_AUTOINCR 0x00000001
-/* Buswitdh is 16 bit */
+/*
+ * Option constants for bizarre disfunctionality and real
+ * features.
+ */
+/* Buswidth is 16 bit */
#define NAND_BUSWIDTH_16 0x00000002
-/* Device supports partial programming without padding */
-#define NAND_NO_PADDING 0x00000004
/* Chip has cache program function */
#define NAND_CACHEPRG 0x00000008
-/* Chip has copy back function */
-#define NAND_COPYBACK 0x00000010
-/* AND Chip which has 4 banks and a confusing page / block
- * assignment. See Renesas datasheet for further information */
-#define NAND_IS_AND 0x00000020
-/* Chip has a array of 4 pages which can be read without
- * additional ready /busy waits */
-#define NAND_4PAGE_ARRAY 0x00000040
-/* Chip requires that BBT is periodically rewritten to prevent
- * bits from adjacent blocks from 'leaking' in altering data.
- * This happens with the Renesas AG-AND chips, possibly others. */
-#define BBT_AUTO_REFRESH 0x00000080
-/* Chip does not require ready check on read. True
- * for all large page devices, as they do not support
- * autoincrement.*/
-#define NAND_NO_READRDY 0x00000100
+/*
+ * Chip requires ready check on read (for auto-incremented sequential read).
+ * True only for small page devices; large page devices do not support
+ * autoincrement.
+ */
+#define NAND_NEED_READRDY 0x00000100
+
/* Chip does not allow subpage writes */
#define NAND_NO_SUBPAGE_WRITE 0x00000200
-/* Buswitdh shal be autodetected */
-#define NAND_BUSWIDTH_AUTO 0x00080000
+/* Device is one of 'new' xD cards that expose fake nand command set */
+#define NAND_BROKEN_XD 0x00000400
+
+/* Device behaves just like nand, but is readonly */
+#define NAND_ROM 0x00000800
+
+/* Device supports subpage reads */
+#define NAND_SUBPAGE_READ 0x00001000
/* Options valid for Samsung large page devices */
-#define NAND_SAMSUNG_LP_OPTIONS \
- (NAND_NO_PADDING | NAND_CACHEPRG | NAND_COPYBACK)
+#define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG
/* Macros to identify the above */
-#define NAND_CANAUTOINCR(chip) (!(chip->options & NAND_NO_AUTOINCR))
-#define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING))
#define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG))
-#define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK))
-
-/* Mask to zero out the chip options, which come from the id table */
-#define NAND_CHIPOPTIONS_MSK (0x0000ffff & ~NAND_NO_AUTOINCR)
+#define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ))
/* Non chip related options */
/* This option skips the bbt scan during initialization. */
-#define NAND_SKIP_BBTSCAN 0x00020000
-/* This option is defined if the board driver allocates its own buffers
- (e.g. because it needs them DMA-coherent */
-#define NAND_OWN_BUFFERS 0x00040000
+#define NAND_SKIP_BBTSCAN 0x00010000
+/*
+ * This option is defined if the board driver allocates its own buffers
+ * (e.g. because it needs them DMA-coherent).
+ */
+#define NAND_OWN_BUFFERS 0x00020000
+/* Chip may not exist, so silence any errors in scan */
+#define NAND_SCAN_SILENT_NODEV 0x00040000
+/*
+ * Autodetect nand buswidth with readid/onfi.
+ * This suppose the driver will configure the hardware in 8 bits mode
+ * when calling nand_scan_ident, and update its configuration
+ * before calling nand_scan_tail.
+ */
+#define NAND_BUSWIDTH_AUTO 0x00080000
+
/* Options set by nand scan */
/* Nand scan has allocated controller struct */
#define NAND_CONTROLLER_ALLOC 0x80000000
@@ -202,23 +197,24 @@ typedef enum {
#define NAND_CI_CHIPNR_MSK 0x03
#define NAND_CI_CELLTYPE_MSK 0x0C
-/*
- * nand_state_t - chip states
- * Enumeration for NAND flash chip state
- */
-typedef enum {
- FL_READY,
- FL_READING,
- FL_WRITING,
- FL_ERASING,
- FL_SYNCING,
- FL_CACHEDPRG,
- FL_PM_SUSPENDED,
-} nand_state_t;
-
/* Keep gcc happy */
struct nand_chip;
+/* ONFI timing mode, used in both asynchronous and synchronous mode */
+#define ONFI_TIMING_MODE_0 (1 << 0)
+#define ONFI_TIMING_MODE_1 (1 << 1)
+#define ONFI_TIMING_MODE_2 (1 << 2)
+#define ONFI_TIMING_MODE_3 (1 << 3)
+#define ONFI_TIMING_MODE_4 (1 << 4)
+#define ONFI_TIMING_MODE_5 (1 << 5)
+#define ONFI_TIMING_MODE_UNKNOWN (1 << 6)
+
+/* ONFI feature address */
+#define ONFI_FEATURE_ADDR_TIMING_MODE 0x1
+
+/* ONFI subfeature parameters length */
+#define ONFI_SUBFEATURE_PARAM_LEN 4
+
struct nand_onfi_params {
/* rev info and features block */
/* 'O' 'N' 'F' 'I' */
@@ -287,77 +283,87 @@ struct nand_onfi_params {
* struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices
* @lock: protection lock
* @active: the mtd device which holds the controller currently
- * @wq: wait queue to sleep on if a NAND operation is in progress
- * used instead of the per chip wait queue when a hw controller is available
+ * @wq: wait queue to sleep on if a NAND operation is in
+ * progress used instead of the per chip wait queue
+ * when a hw controller is available.
*/
struct nand_hw_control {
struct nand_chip *active;
};
/**
- * struct nand_ecc_ctrl - Control structure for ecc
- * @mode: ecc mode
- * @steps: number of ecc steps per page
- * @size: data bytes per ecc step
- * @bytes: ecc bytes per step
+ * struct nand_ecc_ctrl - Control structure for ECC
+ * @mode: ECC mode
+ * @steps: number of ECC steps per page
+ * @size: data bytes per ECC step
+ * @bytes: ECC bytes per step
* @strength: max number of correctible bits per ECC step
- * @total: total number of ecc bytes per page
- * @prepad: padding information for syndrome based ecc generators
- * @postpad: padding information for syndrome based ecc generators
+ * @total: total number of ECC bytes per page
+ * @prepad: padding information for syndrome based ECC generators
+ * @postpad: padding information for syndrome based ECC generators
* @layout: ECC layout control struct pointer
- * @hwctl: function to control hardware ecc generator. Must only
+ * @priv: pointer to private ECC control data
+ * @hwctl: function to control hardware ECC generator. Must only
* be provided if an hardware ECC is available
- * @calculate: function for ecc calculation or readback from ecc hardware
- * @correct: function for ecc correction, matching to ecc generator (sw/hw)
+ * @calculate: function for ECC calculation or readback from ECC hardware
+ * @correct: function for ECC correction, matching to ECC generator (sw/hw)
* @read_page_raw: function to read a raw page without ECC
* @write_page_raw: function to write a raw page without ECC
- * @read_page: function to read a page according to the ecc generator requirements
- * @write_page: function to write a page according to the ecc generator requirements
+ * @read_page: function to read a page according to the ECC generator
+ * requirements; returns maximum number of bitflips corrected in
+ * any single ECC step, 0 if bitflips uncorrectable, -EIO hw error
+ * @read_subpage: function to read parts of the page covered by ECC;
+ * returns same as read_page()
+ * @write_subpage: function to write parts of the page covered by ECC.
+ * @write_page: function to write a page according to the ECC generator
+ * requirements.
+ * @write_oob_raw: function to write chip OOB data without ECC
+ * @read_oob_raw: function to read chip OOB data without ECC
* @read_oob: function to read chip OOB data
* @write_oob: function to write chip OOB data
*/
struct nand_ecc_ctrl {
- nand_ecc_modes_t mode;
- int steps;
- int size;
- int bytes;
- int total;
- int strength;
- int prepad;
- int postpad;
+ nand_ecc_modes_t mode;
+ int steps;
+ int size;
+ int bytes;
+ int total;
+ int strength;
+ int prepad;
+ int postpad;
struct nand_ecclayout *layout;
- void (*hwctl)(struct mtd_info *mtd, int mode);
- int (*calculate)(struct mtd_info *mtd,
- const uint8_t *dat,
- uint8_t *ecc_code);
- int (*correct)(struct mtd_info *mtd, uint8_t *dat,
- uint8_t *read_ecc,
- uint8_t *calc_ecc);
- int (*read_page_raw)(struct mtd_info *mtd,
- struct nand_chip *chip,
- uint8_t *buf);
- void (*write_page_raw)(struct mtd_info *mtd,
- struct nand_chip *chip,
- const uint8_t *buf);
- int (*read_page)(struct mtd_info *mtd,
- struct nand_chip *chip,
- uint8_t *buf);
- void (*write_page)(struct mtd_info *mtd,
- struct nand_chip *chip,
- const uint8_t *buf);
- int (*read_oob)(struct mtd_info *mtd,
- struct nand_chip *chip,
- int page,
- int sndcmd);
- int (*write_oob)(struct mtd_info *mtd,
- struct nand_chip *chip,
- int page);
+ void *priv;
+ void (*hwctl)(struct mtd_info *mtd, int mode);
+ int (*calculate)(struct mtd_info *mtd, const uint8_t *dat,
+ uint8_t *ecc_code);
+ int (*correct)(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc,
+ uint8_t *calc_ecc);
+ int (*read_page_raw)(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page);
+ int (*write_page_raw)(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required);
+ int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int oob_required, int page);
+ int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip,
+ uint32_t offs, uint32_t len, uint8_t *buf);
+ int (*write_subpage)(struct mtd_info *mtd, struct nand_chip *chip,
+ uint32_t offset, uint32_t data_len,
+ const uint8_t *data_buf, int oob_required);
+ int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf, int oob_required);
+ int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip,
+ int page);
+ int (*read_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip,
+ int page);
+ int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page);
+ int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip,
+ int page);
};
/**
* struct nand_buffers - buffer structure for read/write
- * @ecccalc: buffer for calculated ecc
- * @ecccode: buffer for ecc read from flash
+ * @ecccalc: buffer for calculated ECC
+ * @ecccode: buffer for ECC read from flash
* @databuf: buffer for data - dynamically sized
*
* Do not change the order of buffers. databuf and oobrbuf must be in
@@ -371,168 +377,234 @@ struct nand_buffers {
/**
* struct nand_chip - NAND Private Flash Chip Data
- * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device
- * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device
+ * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the
+ * flash device
+ * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the
+ * flash device.
* @read_byte: [REPLACEABLE] read one byte from the chip
* @read_word: [REPLACEABLE] read one word from the chip
* @write_buf: [REPLACEABLE] write data from the buffer to the chip
* @read_buf: [REPLACEABLE] read data from the chip into the buffer
- * @verify_buf: [REPLACEABLE] verify buffer contents against the chip data
* @select_chip: [REPLACEABLE] select chip nr
* @block_bad: [REPLACEABLE] check, if the block is bad
* @block_markbad: [REPLACEABLE] mark the block bad
* @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific function for controlling
* ALE/CLE/nCE. Also used to write command and address
- * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line
- * If set to NULL no access to ready/busy is available and the ready/busy information
- * is read from the chip status register
- * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing commands to the chip
- * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on ready
- * @ecc: [BOARDSPECIFIC] ecc control ctructure
+ * @init_size: [BOARDSPECIFIC] hardwarespecific function for setting
+ * mtd->oobsize, mtd->writesize and so on.
+ * @id_data contains the 8 bytes values of NAND_CMD_READID.
+ * Return with the bus width.
+ * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing
+ * device ready/busy line. If set to NULL no access to
+ * ready/busy is available and the ready/busy information
+ * is read from the chip status register.
+ * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing
+ * commands to the chip.
+ * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on
+ * ready.
+ * @ecc: [BOARDSPECIFIC] ECC control structure
* @buffers: buffer structure for read/write
* @hwcontrol: platform-specific hardware control structure
- * @ops: oob operation operands
- * @erase_cmd: [INTERN] erase command write function, selectable due to AND support
+ * @erase_cmd: [INTERN] erase command write function, selectable due
+ * to AND support.
* @scan_bbt: [REPLACEABLE] function to scan bad block table
- * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR)
- * @wq: [INTERN] wait queue to sleep on if a NAND operation is in progress
+ * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring
+ * data from array to read regs (tR).
* @state: [INTERN] the current state of the NAND device
- * @oob_poi: poison value buffer
- * @page_shift: [INTERN] number of address bits in a page (column address bits)
+ * @oob_poi: "poison value buffer," used for laying out OOB data
+ * before writing
+ * @page_shift: [INTERN] number of address bits in a page (column
+ * address bits).
* @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock
* @bbt_erase_shift: [INTERN] number of address bits in a bbt entry
* @chip_shift: [INTERN] number of address bits in one chip
- * @datbuf: [INTERN] internal buffer for one page + oob
- * @oobbuf: [INTERN] oob buffer for one eraseblock
- * @oobdirty: [INTERN] indicates that oob_buf must be reinitialized
- * @data_poi: [INTERN] pointer to a data buffer
- * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about
- * special functionality. See the defines for further explanation
+ * @options: [BOARDSPECIFIC] various chip options. They can partly
+ * be set to inform nand_scan about special functionality.
+ * See the defines for further explanation.
* @bbt_options: [INTERN] bad block specific options. All options used
* here must come from bbm.h. By default, these options
* will be copied to the appropriate nand_bbt_descr's.
- * @badblockpos: [INTERN] position of the bad block marker in the oob area
+ * @badblockpos: [INTERN] position of the bad block marker in the oob
+ * area.
+ * @badblockbits: [INTERN] minimum number of set bits in a good block's
+ * bad block marker position; i.e., BBM == 11110111b is
+ * not bad when badblockbits == 7
* @cellinfo: [INTERN] MLC/multichip data from chip ident
* @numchips: [INTERN] number of physical chips
* @chipsize: [INTERN] the size of one chip for multichip arrays
* @pagemask: [INTERN] page number mask = number of (pages / chip) - 1
- * @pagebuf: [INTERN] holds the pagenumber which is currently in data_buf
+ * @pagebuf: [INTERN] holds the pagenumber which is currently in
+ * data_buf.
+ * @pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is
+ * currently in data_buf.
* @subpagesize: [INTERN] holds the subpagesize
* @onfi_version: [INTERN] holds the chip ONFI version (BCD encoded),
* non 0 if ONFI supported.
* @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is
* supported, 0 otherwise.
- * @ecclayout: [REPLACEABLE] the default ecc placement scheme
+ * @onfi_set_features: [REPLACEABLE] set the features for ONFI nand
+ * @onfi_get_features: [REPLACEABLE] get the features for ONFI nand
+ * @ecclayout: [REPLACEABLE] the default ECC placement scheme
* @bbt: [INTERN] bad block table pointer
- * @bbt_td: [REPLACEABLE] bad block table descriptor for flash lookup
+ * @bbt_td: [REPLACEABLE] bad block table descriptor for flash
+ * lookup.
* @bbt_md: [REPLACEABLE] bad block table mirror descriptor
- * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial bad block scan
- * @controller: [REPLACEABLE] a pointer to a hardware controller structure
- * which is shared among multiple independend devices
- * @priv: [OPTIONAL] pointer to private chip date
- * @errstat: [OPTIONAL] hardware specific function to perform additional error status checks
- * (determine if errors are correctable)
+ * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial
+ * bad block scan.
+ * @controller: [REPLACEABLE] a pointer to a hardware controller
+ * structure which is shared among multiple independent
+ * devices.
+ * @priv: [OPTIONAL] pointer to private chip data
+ * @errstat: [OPTIONAL] hardware specific function to perform
+ * additional error status checks (determine if errors are
+ * correctable).
* @write_page: [REPLACEABLE] High-level page write function
*/
-struct nand_chip {
- void __iomem *IO_ADDR_R;
- void __iomem *IO_ADDR_W;
-
- uint8_t (*read_byte)(struct mtd_info *mtd);
- u16 (*read_word)(struct mtd_info *mtd);
- void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
- void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
- int (*verify_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
- void (*select_chip)(struct mtd_info *mtd, int chip);
- int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip);
- int (*block_markbad)(struct mtd_info *mtd, loff_t ofs);
- void (*cmd_ctrl)(struct mtd_info *mtd, int dat,
- unsigned int ctrl);
- int (*dev_ready)(struct mtd_info *mtd);
- void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr);
- int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this);
- void (*erase_cmd)(struct mtd_info *mtd, int page);
- int (*scan_bbt)(struct mtd_info *mtd);
- int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state, int status, int page);
- int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
- const uint8_t *buf, int page, int cached, int raw);
- int (*set_buswidth)(struct mtd_info *mtd, struct nand_chip *this, int buswidth);
-
- int chip_delay;
- unsigned int options;
- unsigned int bbt_options;
-
- int page_shift;
- int phys_erase_shift;
- int bbt_erase_shift;
- int chip_shift;
- int numchips;
- uint64_t chipsize;
- int pagemask;
- int pagebuf;
- int subpagesize;
- uint8_t cellinfo;
- int badblockpos;
+struct nand_chip {
+ void __iomem *IO_ADDR_R;
+ void __iomem *IO_ADDR_W;
+
+ uint8_t (*read_byte)(struct mtd_info *mtd);
+ u16 (*read_word)(struct mtd_info *mtd);
+ void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
+ void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
+ void (*select_chip)(struct mtd_info *mtd, int chip);
+ int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip);
+ int (*block_markbad)(struct mtd_info *mtd, loff_t ofs);
+ void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl);
+ int (*init_size)(struct mtd_info *mtd, struct nand_chip *this,
+ u8 *id_data);
+ int (*dev_ready)(struct mtd_info *mtd);
+ void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column,
+ int page_addr);
+ int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this);
+ void (*erase_cmd)(struct mtd_info *mtd, int page);
+ int (*scan_bbt)(struct mtd_info *mtd);
+ int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state,
+ int status, int page);
+ int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip,
+ uint32_t offset, int data_len, const uint8_t *buf,
+ int oob_required, int page, int cached, int raw);
+ int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip,
+ int feature_addr, uint8_t *subfeature_para);
+ int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip,
+ int feature_addr, uint8_t *subfeature_para);
+
+ int chip_delay;
+ unsigned int options;
+ unsigned int bbt_options;
+
+ int page_shift;
+ int phys_erase_shift;
+ int bbt_erase_shift;
+ int chip_shift;
+ int numchips;
+ uint64_t chipsize;
+ int pagemask;
+ int pagebuf;
+ unsigned int pagebuf_bitflips;
+ int subpagesize;
+ uint8_t cellinfo;
+ int badblockpos;
+ int badblockbits;
int onfi_version;
- struct nand_onfi_params onfi_params;
+ struct nand_onfi_params onfi_params;
- nand_state_t state;
+ flstate_t state;
- uint8_t *oob_poi;
- struct nand_hw_control *controller;
- struct nand_ecclayout *ecclayout;
+ uint8_t *oob_poi;
+ struct nand_hw_control *controller;
+ struct nand_ecclayout *ecclayout;
struct nand_ecc_ctrl ecc;
struct nand_buffers *buffers;
struct nand_hw_control hwcontrol;
- struct mtd_oob_ops ops;
-
- uint8_t *bbt;
- struct nand_bbt_descr *bbt_td;
- struct nand_bbt_descr *bbt_md;
+ uint8_t *bbt;
+ struct nand_bbt_descr *bbt_td;
+ struct nand_bbt_descr *bbt_md;
- struct nand_bbt_descr *badblock_pattern;
+ struct nand_bbt_descr *badblock_pattern;
- void *priv;
+ void *priv;
};
/*
* NAND Flash Manufacturer ID Codes
*/
-#define NAND_MFR_TOSHIBA 0x98
-#define NAND_MFR_SAMSUNG 0xec
-#define NAND_MFR_FUJITSU 0x04
-#define NAND_MFR_NATIONAL 0x8f
-#define NAND_MFR_RENESAS 0x07
-#define NAND_MFR_STMICRO 0x20
-#define NAND_MFR_HYNIX 0xad
-#define NAND_MFR_MICRON 0x2c
-#define NAND_MFR_AMD 0x01
-#define NAND_MFR_MACRONIX 0xc2
-#define NAND_MFR_EON 0x92
+#define NAND_MFR_TOSHIBA 0x98
+#define NAND_MFR_SAMSUNG 0xec
+#define NAND_MFR_FUJITSU 0x04
+#define NAND_MFR_NATIONAL 0x8f
+#define NAND_MFR_RENESAS 0x07
+#define NAND_MFR_STMICRO 0x20
+#define NAND_MFR_HYNIX 0xad
+#define NAND_MFR_MICRON 0x2c
+#define NAND_MFR_AMD 0x01
+#define NAND_MFR_MACRONIX 0xc2
+#define NAND_MFR_EON 0x92
+
+/* The maximum expected count of bytes in the NAND ID sequence */
+#define NAND_MAX_ID_LEN 8
+
+/*
+ * A helper for defining older NAND chips where the second ID byte fully
+ * defined the chip, including the geometry (chip size, eraseblock size, page
+ * size). All these chips have 512 bytes NAND page size.
+ */
+#define LEGACY_ID_NAND(nm, devid, chipsz, erasesz, opts) \
+ { .name = (nm), {{ .dev_id = (devid) }}, .pagesize = 512, \
+ .chipsize = (chipsz), .erasesize = (erasesz), .options = (opts) }
+
+/*
+ * A helper for defining newer chips which report their page size and
+ * eraseblock size via the extended ID bytes.
+ *
+ * The real difference between LEGACY_ID_NAND and EXTENDED_ID_NAND is that with
+ * EXTENDED_ID_NAND, manufacturers overloaded the same device ID so that the
+ * device ID now only represented a particular total chip size (and voltage,
+ * buswidth), and the page size, eraseblock size, and OOB size could vary while
+ * using the same device ID.
+ */
+#define EXTENDED_ID_NAND(nm, devid, chipsz, opts) \
+ { .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \
+ .options = (opts) }
/**
* struct nand_flash_dev - NAND Flash Device ID Structure
- * @name: Identify the device type
- * @id: device ID code
- * @pagesize: Pagesize in bytes. Either 256 or 512 or 0
- * If the pagesize is 0, then the real pagesize
- * and the eraseize are determined from the
- * extended id bytes in the chip
- * @erasesize: Size of an erase block in the flash device.
- * @chipsize: Total chipsize in Mega Bytes
- * @options: Bitfield to store chip relevant options
+ * @name: a human-readable name of the NAND chip
+ * @dev_id: the device ID (the second byte of the full chip ID array)
+ * @mfr_id: manufecturer ID part of the full chip ID array (refers the same
+ * memory address as @id[0])
+ * @dev_id: device ID part of the full chip ID array (refers the same memory
+ * address as @id[1])
+ * @id: full device ID array
+ * @pagesize: size of the NAND page in bytes; if 0, then the real page size (as
+ * well as the eraseblock size) is determined from the extended NAND
+ * chip ID array)
+ * @chipsize: total chip size in MiB
+ * @erasesize: eraseblock size in bytes (determined from the extended ID if 0)
+ * @options: stores various chip bit options
+ * @id_len: The valid length of the @id.
+ * @oobsize: OOB size
*/
struct nand_flash_dev {
char *name;
- int id;
- unsigned long pagesize;
- unsigned long chipsize;
- unsigned long erasesize;
- unsigned long options;
+ union {
+ struct {
+ uint8_t mfr_id;
+ uint8_t dev_id;
+ };
+ uint8_t id[NAND_MAX_ID_LEN];
+ };
+ unsigned int pagesize;
+ unsigned int chipsize;
+ unsigned int erasesize;
+ unsigned int options;
+ uint16_t id_len;
+ uint16_t oobsize;
};
/**
@@ -542,7 +614,7 @@ struct nand_flash_dev {
*/
struct nand_manufacturers {
int id;
- char * name;
+ char *name;
};
extern struct nand_flash_dev nand_flash_ids[];
@@ -555,13 +627,8 @@ extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt);
extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
int allowbbt);
extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len,
- size_t * retlen, uint8_t * buf);
+ size_t *retlen, uint8_t *buf);
extern int add_mtd_nand_device(struct mtd_info *mtd, char *devname);
-/*
-* Constants for oob configuration
-*/
-#define NAND_SMALL_BADBLOCK_POS 5
-#define NAND_LARGE_BADBLOCK_POS 0
/**
* struct platform_nand_chip - chip level device structure
@@ -571,40 +638,52 @@ extern int add_mtd_nand_device(struct mtd_info *mtd, char *devname);
* @partitions: mtd partition list
* @chip_delay: R/B delay value in us
* @options: Option flags, e.g. 16bit buswidth
- * @ecclayout: ecc layout info structure
+ * @bbt_options: BBT option flags, e.g. NAND_BBT_USE_FLASH
+ * @ecclayout: ECC layout info structure
* @part_probe_types: NULL-terminated array of probe types
- * @priv: hardware controller specific settings
*/
struct platform_nand_chip {
- int nr_chips;
- int chip_offset;
- int nr_partitions;
- struct mtd_partition *partitions;
- struct nand_ecclayout *ecclayout;
- int chip_delay;
- unsigned int options;
- const char **part_probe_types;
- void *priv;
+ int nr_chips;
+ int chip_offset;
+ int nr_partitions;
+ struct mtd_partition *partitions;
+ struct nand_ecclayout *ecclayout;
+ int chip_delay;
+ unsigned int options;
+ unsigned int bbt_options;
+ const char **part_probe_types;
};
+/* Keep gcc happy */
+struct platform_device;
+
/**
* struct platform_nand_ctrl - controller level device structure
+ * @probe: platform specific function to probe/setup hardware
+ * @remove: platform specific function to remove/teardown hardware
* @hwcontrol: platform specific hardware control structure
* @dev_ready: platform specific function to read ready/busy pin
* @select_chip: platform specific chip select function
* @cmd_ctrl: platform specific function for controlling
* ALE/CLE/nCE. Also used to write command and address
+ * @write_buf: platform specific function for write buffer
+ * @read_buf: platform specific function for read buffer
+ * @read_byte: platform specific function to read one byte from chip
* @priv: private data to transport driver specific settings
*
* All fields are optional and depend on the hardware driver requirements
*/
struct platform_nand_ctrl {
- void (*hwcontrol)(struct mtd_info *mtd, int cmd);
- int (*dev_ready)(struct mtd_info *mtd);
- void (*select_chip)(struct mtd_info *mtd, int chip);
- void (*cmd_ctrl)(struct mtd_info *mtd, int dat,
- unsigned int ctrl);
- void *priv;
+ int (*probe)(struct platform_device *pdev);
+ void (*remove)(struct platform_device *pdev);
+ void (*hwcontrol)(struct mtd_info *mtd, int cmd);
+ int (*dev_ready)(struct mtd_info *mtd);
+ void (*select_chip)(struct mtd_info *mtd, int chip);
+ void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl);
+ void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
+ void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
+ unsigned char (*read_byte)(struct mtd_info *mtd);
+ void *priv;
};
/**
@@ -613,8 +692,8 @@ struct platform_nand_ctrl {
* @ctrl: controller level device structure
*/
struct platform_nand_data {
- struct platform_nand_chip chip;
- struct platform_nand_ctrl ctrl;
+ struct platform_nand_chip chip;
+ struct platform_nand_ctrl ctrl;
};
/* Some helpers to access the data structures */
@@ -626,6 +705,20 @@ struct platform_nand_chip *get_platform_nandchip(struct mtd_info *mtd)
return chip->priv;
}
-#endif /* DOXYGEN_SHOULD_SKIP_THIS */
+/* return the supported asynchronous timing mode. */
+static inline int onfi_get_async_timing_mode(struct nand_chip *chip)
+{
+ if (!chip->onfi_version)
+ return ONFI_TIMING_MODE_UNKNOWN;
+ return le16_to_cpu(chip->onfi_params.async_timing_mode);
+}
+
+/* return the supported synchronous timing mode. */
+static inline int onfi_get_sync_timing_mode(struct nand_chip *chip)
+{
+ if (!chip->onfi_version)
+ return ONFI_TIMING_MODE_UNKNOWN;
+ return le16_to_cpu(chip->onfi_params.src_sync_timing_mode);
+}
#endif /* __LINUX_MTD_NAND_H */
--
1.8.3.2
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 9+ messages in thread