mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: "Alexander Shiyan" <shc_work@mail.ru>
To: "Sascha Hauer" <s.hauer@pengutronix.de>
Cc: barebox@lists.infradead.org
Subject: Re: PCM038 USB is broken again
Date: Mon, 12 Aug 2013 14:56:56 +0400	[thread overview]
Message-ID: <1376305016.963613355@f136.i.mail.ru> (raw)
In-Reply-To: <20130812070759.GL26614@pengutronix.de>




Понедельник, 12 августа 2013, 9:07 +02:00 от Sascha Hauer <s.hauer@pengutronix.de>:
> On Sat, Aug 10, 2013 at 08:10:53AM +0400, Alexander Shiyan wrote:
> > Hello.
> > 
> > USB functionality on PCM038 (PCM970) is broken again due
> > patch "Revert usb: chipidea-imx: Fix usb initialization".
> > 
> > Board: Phytec phyCORE-i.MX27
> > detected i.MX27 revision 2.1
> > netconsole: registered as cs1
> > mc13xxx-spi mc137830: Found MC13783 ID: 0x00009b [Rev: 3.1]
> > cfi_flash cfi_flash0: found cfi flash at c0000000, size 33554432
> > nand: NAND device: Manufacturer ID: 0x20, Chip ID: 0x36 (ST Micro NAND 64MiB 1,8V 8-bit), 64MiB, page size: 512, OOB size: 16
> > Bad block table found at page 131040, version 0x01
> > Bad block table found at page 131008, version 0x01
> > imxfb imxfb: i.MX Framebuffer driver
> > mdio_bus: miibus0: probed
> > No ULPI found. vid: 0x0000 pid: 0x0000
> > pcm038: Using environment in NOR Flash
> > No ULPI found. vid: 0x0000 pid: 0x0000
> > imx-usb imx-usb2: USB EHCI 1.00
> > imx-mmc imx-mmc1: registered as imx-mmc1
> > running /env/bin/init...
> > 
> > After remove this patch, all works fine.
> 
> Have you verified it really doesn't work? I get the 'No ULPI found'
> message aswell, but the ULPI phys are probed again during the 'usb'
> command and it then works here.

Same result on CCMX51.

barebox 2013.06.0-00186-gae970c3 #12 Tue Jul 2 13:56:48 MSK 2013
Board: ConnectCore i.MX51
detected i.MX51 revision 3.0
Module Variant: i.MX515@600MHz, PHY, Accel (0x0b)
Module HW Rev : 03
Module Serial : B111156789
mc13xxx-spi mc13xxx-spi0: Found MC13892 ID: 0x0045d0 [Rev: 2.0a]
nand: ONFI param page 0 valid
nand: ONFI flash detected ... nand: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), page size: 2048, OOB size: 64
malloc space: 0x95f00000 -> 0x97efffff (size 32 MiB)
imx-esdhc imx-esdhc0: registered as imx-esdhc0
Found NXP ISP150x ULPI transceiver (0x04cc:0x1504).
imx-usb imx-usb1: USB EHCI 1.00
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...

...

barebox 2013.08.0-00157-g9b0907b-dirty #3 Mon Aug 12 14:47:06 MSK 2013
Board: ConnectCore i.MX51
detected i.MX51 revision 3.0
Module Variant: i.MX515@600MHz, PHY, Accel (0x0b)
Module HW Rev : 03
Module Serial : B111156789
mc13xxx-spi mc138920: Found MC13892 ID: 0x0045d0 [Rev: 2.0a]
nand: ONFI param page 0 valid
nand: ONFI flash detected
nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD), 256MiB, page size: 2048, OOB size: 64
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
malloc space: 0x95f00000 -> 0x97efffff (size 32 MiB)
imx-esdhc imx-esdhc0: registered as imx-esdhc0
No ULPI found. vid: 0x0000 pid: 0x0000
imx-usb imx-usb1: USB EHCI 1.00
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...

...
And yes, this works after "usb" command:
barebox@ConnectCore i.MX51:/ usb
USB: scanning bus for devices...
Found NXP ISP150x ULPI transceiver (0x04cc:0x1504).
Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
1 USB Device(s) found

So, you consider this is not a bug?

---
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  reply	other threads:[~2013-08-12 10:57 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-08-10  4:10 Alexander Shiyan
2013-08-12  7:07 ` Sascha Hauer
2013-08-12 10:56   ` Alexander Shiyan [this message]
2013-08-13  6:26     ` Sascha Hauer
2013-08-15 19:32       ` Alexander Shiyan
2013-08-16  8:01         ` Sascha Hauer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1376305016.963613355@f136.i.mail.ru \
    --to=shc_work@mail.ru \
    --cc=barebox@lists.infradead.org \
    --cc=s.hauer@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox