mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Sascha Hauer <s.hauer@pengutronix.de>
To: Barebox List <barebox@lists.infradead.org>
Subject: [PATCH 3/7] pci: pci_regs.h: Sync with Linux
Date: Tue, 17 Mar 2015 07:38:47 +0100	[thread overview]
Message-ID: <1426574331-22797-4-git-send-email-s.hauer@pengutronix.de> (raw)
In-Reply-To: <1426574331-22797-1-git-send-email-s.hauer@pengutronix.de>

Sync the pci register definitions with Linux 4.0-rc1. Some are needed
for the upcoming designware pcie driver.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 include/linux/pci_regs.h | 769 +++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 769 insertions(+)

diff --git a/include/linux/pci_regs.h b/include/linux/pci_regs.h
index 8669fc7..efe3443 100644
--- a/include/linux/pci_regs.h
+++ b/include/linux/pci_regs.h
@@ -26,6 +26,7 @@
  * Under PCI, each device has 256 bytes of configuration address space,
  * of which the first 64 bytes are standardized as follows:
  */
+#define PCI_STD_HEADER_SIZEOF	64
 #define PCI_VENDOR_ID		0x00	/* 16 bits */
 #define PCI_DEVICE_ID		0x02	/* 16 bits */
 #define PCI_COMMAND		0x04	/* 16 bits */
@@ -107,6 +108,14 @@
 #define  PCI_ROM_ADDRESS_ENABLE	0x01
 #define PCI_ROM_ADDRESS_MASK	(~0x7ffUL)
 
+#define PCI_CAPABILITY_LIST	0x34	/* Offset of first capability list entry */
+
+/* 0x35-0x3b are reserved */
+#define PCI_INTERRUPT_LINE	0x3c	/* 8 bits */
+#define PCI_INTERRUPT_PIN	0x3d	/* 8 bits */
+#define PCI_MIN_GNT		0x3e	/* 8 bits */
+#define PCI_MAX_LAT		0x3f	/* 8 bits */
+
 /* Header type 1 (PCI-to-PCI bridges) */
 #define PCI_PRIMARY_BUS		0x18	/* Primary bus number */
 #define PCI_SECONDARY_BUS	0x19	/* Secondary bus number */
@@ -134,5 +143,765 @@
 #define PCI_PREF_LIMIT_UPPER32	0x2c
 #define PCI_IO_BASE_UPPER16	0x30	/* Upper half of I/O addresses */
 #define PCI_IO_LIMIT_UPPER16	0x32
+/* 0x34 same as for htype 0 */
+/* 0x35-0x3b is reserved */
+#define PCI_ROM_ADDRESS1	0x38	/* Same as PCI_ROM_ADDRESS, but for htype 1 */
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_BRIDGE_CONTROL	0x3e
+#define  PCI_BRIDGE_CTL_PARITY	0x01	/* Enable parity detection on secondary interface */
+#define  PCI_BRIDGE_CTL_SERR	0x02	/* The same for SERR forwarding */
+#define  PCI_BRIDGE_CTL_ISA	0x04	/* Enable ISA mode */
+#define  PCI_BRIDGE_CTL_VGA	0x08	/* Forward VGA addresses */
+#define  PCI_BRIDGE_CTL_MASTER_ABORT	0x20  /* Report master aborts */
+#define  PCI_BRIDGE_CTL_BUS_RESET	0x40	/* Secondary bus reset */
+#define  PCI_BRIDGE_CTL_FAST_BACK	0x80	/* Fast Back2Back enabled on secondary interface */
+
+/* Header type 2 (CardBus bridges) */
+#define PCI_CB_CAPABILITY_LIST	0x14
+/* 0x15 reserved */
+#define PCI_CB_SEC_STATUS	0x16	/* Secondary status */
+#define PCI_CB_PRIMARY_BUS	0x18	/* PCI bus number */
+#define PCI_CB_CARD_BUS		0x19	/* CardBus bus number */
+#define PCI_CB_SUBORDINATE_BUS	0x1a	/* Subordinate bus number */
+#define PCI_CB_LATENCY_TIMER	0x1b	/* CardBus latency timer */
+#define PCI_CB_MEMORY_BASE_0	0x1c
+#define PCI_CB_MEMORY_LIMIT_0	0x20
+#define PCI_CB_MEMORY_BASE_1	0x24
+#define PCI_CB_MEMORY_LIMIT_1	0x28
+#define PCI_CB_IO_BASE_0	0x2c
+#define PCI_CB_IO_BASE_0_HI	0x2e
+#define PCI_CB_IO_LIMIT_0	0x30
+#define PCI_CB_IO_LIMIT_0_HI	0x32
+#define PCI_CB_IO_BASE_1	0x34
+#define PCI_CB_IO_BASE_1_HI	0x36
+#define PCI_CB_IO_LIMIT_1	0x38
+#define PCI_CB_IO_LIMIT_1_HI	0x3a
+#define  PCI_CB_IO_RANGE_MASK	(~0x03UL)
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_CB_BRIDGE_CONTROL	0x3e
+#define  PCI_CB_BRIDGE_CTL_PARITY	0x01	/* Similar to standard bridge control register */
+#define  PCI_CB_BRIDGE_CTL_SERR		0x02
+#define  PCI_CB_BRIDGE_CTL_ISA		0x04
+#define  PCI_CB_BRIDGE_CTL_VGA		0x08
+#define  PCI_CB_BRIDGE_CTL_MASTER_ABORT	0x20
+#define  PCI_CB_BRIDGE_CTL_CB_RESET	0x40	/* CardBus reset */
+#define  PCI_CB_BRIDGE_CTL_16BIT_INT	0x80	/* Enable interrupt for 16-bit cards */
+#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100	/* Prefetch enable for both memory regions */
+#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
+#define  PCI_CB_BRIDGE_CTL_POST_WRITES	0x400
+#define PCI_CB_SUBSYSTEM_VENDOR_ID	0x40
+#define PCI_CB_SUBSYSTEM_ID		0x42
+#define PCI_CB_LEGACY_MODE_BASE		0x44	/* 16-bit PC Card legacy mode base address (ExCa) */
+/* 0x48-0x7f reserved */
+
+/* Capability lists */
+
+#define PCI_CAP_LIST_ID		0	/* Capability ID */
+#define  PCI_CAP_ID_PM		0x01	/* Power Management */
+#define  PCI_CAP_ID_AGP		0x02	/* Accelerated Graphics Port */
+#define  PCI_CAP_ID_VPD		0x03	/* Vital Product Data */
+#define  PCI_CAP_ID_SLOTID	0x04	/* Slot Identification */
+#define  PCI_CAP_ID_MSI		0x05	/* Message Signalled Interrupts */
+#define  PCI_CAP_ID_CHSWP	0x06	/* CompactPCI HotSwap */
+#define  PCI_CAP_ID_PCIX	0x07	/* PCI-X */
+#define  PCI_CAP_ID_HT		0x08	/* HyperTransport */
+#define  PCI_CAP_ID_VNDR	0x09	/* Vendor-Specific */
+#define  PCI_CAP_ID_DBG		0x0A	/* Debug port */
+#define  PCI_CAP_ID_CCRC	0x0B	/* CompactPCI Central Resource Control */
+#define  PCI_CAP_ID_SHPC	0x0C	/* PCI Standard Hot-Plug Controller */
+#define  PCI_CAP_ID_SSVID	0x0D	/* Bridge subsystem vendor/device ID */
+#define  PCI_CAP_ID_AGP3	0x0E	/* AGP Target PCI-PCI bridge */
+#define  PCI_CAP_ID_SECDEV	0x0F	/* Secure Device */
+#define  PCI_CAP_ID_EXP		0x10	/* PCI Express */
+#define  PCI_CAP_ID_MSIX	0x11	/* MSI-X */
+#define  PCI_CAP_ID_SATA	0x12	/* SATA Data/Index Conf. */
+#define  PCI_CAP_ID_AF		0x13	/* PCI Advanced Features */
+#define  PCI_CAP_ID_MAX		PCI_CAP_ID_AF
+#define PCI_CAP_LIST_NEXT	1	/* Next capability in the list */
+#define PCI_CAP_FLAGS		2	/* Capability defined flags (16 bits) */
+#define PCI_CAP_SIZEOF		4
+
+/* Power Management Registers */
+
+#define PCI_PM_PMC		2	/* PM Capabilities Register */
+#define  PCI_PM_CAP_VER_MASK	0x0007	/* Version */
+#define  PCI_PM_CAP_PME_CLOCK	0x0008	/* PME clock required */
+#define  PCI_PM_CAP_RESERVED    0x0010  /* Reserved field */
+#define  PCI_PM_CAP_DSI		0x0020	/* Device specific initialization */
+#define  PCI_PM_CAP_AUX_POWER	0x01C0	/* Auxiliary power support mask */
+#define  PCI_PM_CAP_D1		0x0200	/* D1 power state support */
+#define  PCI_PM_CAP_D2		0x0400	/* D2 power state support */
+#define  PCI_PM_CAP_PME		0x0800	/* PME pin supported */
+#define  PCI_PM_CAP_PME_MASK	0xF800	/* PME Mask of all supported states */
+#define  PCI_PM_CAP_PME_D0	0x0800	/* PME# from D0 */
+#define  PCI_PM_CAP_PME_D1	0x1000	/* PME# from D1 */
+#define  PCI_PM_CAP_PME_D2	0x2000	/* PME# from D2 */
+#define  PCI_PM_CAP_PME_D3	0x4000	/* PME# from D3 (hot) */
+#define  PCI_PM_CAP_PME_D3cold	0x8000	/* PME# from D3 (cold) */
+#define  PCI_PM_CAP_PME_SHIFT	11	/* Start of the PME Mask in PMC */
+#define PCI_PM_CTRL		4	/* PM control and status register */
+#define  PCI_PM_CTRL_STATE_MASK	0x0003	/* Current power state (D0 to D3) */
+#define  PCI_PM_CTRL_NO_SOFT_RESET	0x0008	/* No reset for D3hot->D0 */
+#define  PCI_PM_CTRL_PME_ENABLE	0x0100	/* PME pin enable */
+#define  PCI_PM_CTRL_DATA_SEL_MASK	0x1e00	/* Data select (??) */
+#define  PCI_PM_CTRL_DATA_SCALE_MASK	0x6000	/* Data scale (??) */
+#define  PCI_PM_CTRL_PME_STATUS	0x8000	/* PME pin status */
+#define PCI_PM_PPB_EXTENSIONS	6	/* PPB support extensions (??) */
+#define  PCI_PM_PPB_B2_B3	0x40	/* Stop clock when in D3hot (??) */
+#define  PCI_PM_BPCC_ENABLE	0x80	/* Bus power/clock control enable (??) */
+#define PCI_PM_DATA_REGISTER	7	/* (??) */
+#define PCI_PM_SIZEOF		8
+
+/* AGP registers */
+
+#define PCI_AGP_VERSION		2	/* BCD version number */
+#define PCI_AGP_RFU		3	/* Rest of capability flags */
+#define PCI_AGP_STATUS		4	/* Status register */
+#define  PCI_AGP_STATUS_RQ_MASK	0xff000000	/* Maximum number of requests - 1 */
+#define  PCI_AGP_STATUS_SBA	0x0200	/* Sideband addressing supported */
+#define  PCI_AGP_STATUS_64BIT	0x0020	/* 64-bit addressing supported */
+#define  PCI_AGP_STATUS_FW	0x0010	/* FW transfers supported */
+#define  PCI_AGP_STATUS_RATE4	0x0004	/* 4x transfer rate supported */
+#define  PCI_AGP_STATUS_RATE2	0x0002	/* 2x transfer rate supported */
+#define  PCI_AGP_STATUS_RATE1	0x0001	/* 1x transfer rate supported */
+#define PCI_AGP_COMMAND		8	/* Control register */
+#define  PCI_AGP_COMMAND_RQ_MASK 0xff000000  /* Master: Maximum number of requests */
+#define  PCI_AGP_COMMAND_SBA	0x0200	/* Sideband addressing enabled */
+#define  PCI_AGP_COMMAND_AGP	0x0100	/* Allow processing of AGP transactions */
+#define  PCI_AGP_COMMAND_64BIT	0x0020	/* Allow processing of 64-bit addresses */
+#define  PCI_AGP_COMMAND_FW	0x0010	/* Force FW transfers */
+#define  PCI_AGP_COMMAND_RATE4	0x0004	/* Use 4x rate */
+#define  PCI_AGP_COMMAND_RATE2	0x0002	/* Use 2x rate */
+#define  PCI_AGP_COMMAND_RATE1	0x0001	/* Use 1x rate */
+#define PCI_AGP_SIZEOF		12
+
+/* Vital Product Data */
+
+#define PCI_VPD_ADDR		2	/* Address to access (15 bits!) */
+#define  PCI_VPD_ADDR_MASK	0x7fff	/* Address mask */
+#define  PCI_VPD_ADDR_F		0x8000	/* Write 0, 1 indicates completion */
+#define PCI_VPD_DATA		4	/* 32-bits of data returned here */
+#define PCI_CAP_VPD_SIZEOF	8
+
+/* Slot Identification */
+
+#define PCI_SID_ESR		2	/* Expansion Slot Register */
+#define  PCI_SID_ESR_NSLOTS	0x1f	/* Number of expansion slots available */
+#define  PCI_SID_ESR_FIC	0x20	/* First In Chassis Flag */
+#define PCI_SID_CHASSIS_NR	3	/* Chassis Number */
+
+/* Message Signalled Interrupts registers */
+
+#define PCI_MSI_FLAGS		2	/* Message Control */
+#define  PCI_MSI_FLAGS_ENABLE	0x0001	/* MSI feature enabled */
+#define  PCI_MSI_FLAGS_QMASK	0x000e	/* Maximum queue size available */
+#define  PCI_MSI_FLAGS_QSIZE	0x0070	/* Message queue size configured */
+#define  PCI_MSI_FLAGS_64BIT	0x0080	/* 64-bit addresses allowed */
+#define  PCI_MSI_FLAGS_MASKBIT	0x0100	/* Per-vector masking capable */
+#define PCI_MSI_RFU		3	/* Rest of capability flags */
+#define PCI_MSI_ADDRESS_LO	4	/* Lower 32 bits */
+#define PCI_MSI_ADDRESS_HI	8	/* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
+#define PCI_MSI_DATA_32		8	/* 16 bits of data for 32-bit devices */
+#define PCI_MSI_MASK_32		12	/* Mask bits register for 32-bit devices */
+#define PCI_MSI_PENDING_32	16	/* Pending intrs for 32-bit devices */
+#define PCI_MSI_DATA_64		12	/* 16 bits of data for 64-bit devices */
+#define PCI_MSI_MASK_64		16	/* Mask bits register for 64-bit devices */
+#define PCI_MSI_PENDING_64	20	/* Pending intrs for 64-bit devices */
+
+/* MSI-X registers */
+#define PCI_MSIX_FLAGS		2	/* Message Control */
+#define  PCI_MSIX_FLAGS_QSIZE	0x07FF	/* Table size */
+#define  PCI_MSIX_FLAGS_MASKALL	0x4000	/* Mask all vectors for this function */
+#define  PCI_MSIX_FLAGS_ENABLE	0x8000	/* MSI-X enable */
+#define PCI_MSIX_TABLE		4	/* Table offset */
+#define  PCI_MSIX_TABLE_BIR	0x00000007 /* BAR index */
+#define  PCI_MSIX_TABLE_OFFSET	0xfffffff8 /* Offset into specified BAR */
+#define PCI_MSIX_PBA		8	/* Pending Bit Array offset */
+#define  PCI_MSIX_PBA_BIR	0x00000007 /* BAR index */
+#define  PCI_MSIX_PBA_OFFSET	0xfffffff8 /* Offset into specified BAR */
+#define PCI_CAP_MSIX_SIZEOF	12	/* size of MSIX registers */
+
+/* MSI-X Table entry format */
+#define PCI_MSIX_ENTRY_SIZE		16
+#define  PCI_MSIX_ENTRY_LOWER_ADDR	0
+#define  PCI_MSIX_ENTRY_UPPER_ADDR	4
+#define  PCI_MSIX_ENTRY_DATA		8
+#define  PCI_MSIX_ENTRY_VECTOR_CTRL	12
+#define   PCI_MSIX_ENTRY_CTRL_MASKBIT	1
+
+/* CompactPCI Hotswap Register */
+
+#define PCI_CHSWP_CSR		2	/* Control and Status Register */
+#define  PCI_CHSWP_DHA		0x01	/* Device Hiding Arm */
+#define  PCI_CHSWP_EIM		0x02	/* ENUM# Signal Mask */
+#define  PCI_CHSWP_PIE		0x04	/* Pending Insert or Extract */
+#define  PCI_CHSWP_LOO		0x08	/* LED On / Off */
+#define  PCI_CHSWP_PI		0x30	/* Programming Interface */
+#define  PCI_CHSWP_EXT		0x40	/* ENUM# status - extraction */
+#define  PCI_CHSWP_INS		0x80	/* ENUM# status - insertion */
+
+/* PCI Advanced Feature registers */
+
+#define PCI_AF_LENGTH		2
+#define PCI_AF_CAP		3
+#define  PCI_AF_CAP_TP		0x01
+#define  PCI_AF_CAP_FLR		0x02
+#define PCI_AF_CTRL		4
+#define  PCI_AF_CTRL_FLR	0x01
+#define PCI_AF_STATUS		5
+#define  PCI_AF_STATUS_TP	0x01
+#define PCI_CAP_AF_SIZEOF	6	/* size of AF registers */
+
+/* PCI-X registers (Type 0 (non-bridge) devices) */
+
+#define PCI_X_CMD		2	/* Modes & Features */
+#define  PCI_X_CMD_DPERR_E	0x0001	/* Data Parity Error Recovery Enable */
+#define  PCI_X_CMD_ERO		0x0002	/* Enable Relaxed Ordering */
+#define  PCI_X_CMD_READ_512	0x0000	/* 512 byte maximum read byte count */
+#define  PCI_X_CMD_READ_1K	0x0004	/* 1Kbyte maximum read byte count */
+#define  PCI_X_CMD_READ_2K	0x0008	/* 2Kbyte maximum read byte count */
+#define  PCI_X_CMD_READ_4K	0x000c	/* 4Kbyte maximum read byte count */
+#define  PCI_X_CMD_MAX_READ	0x000c	/* Max Memory Read Byte Count */
+				/* Max # of outstanding split transactions */
+#define  PCI_X_CMD_SPLIT_1	0x0000	/* Max 1 */
+#define  PCI_X_CMD_SPLIT_2	0x0010	/* Max 2 */
+#define  PCI_X_CMD_SPLIT_3	0x0020	/* Max 3 */
+#define  PCI_X_CMD_SPLIT_4	0x0030	/* Max 4 */
+#define  PCI_X_CMD_SPLIT_8	0x0040	/* Max 8 */
+#define  PCI_X_CMD_SPLIT_12	0x0050	/* Max 12 */
+#define  PCI_X_CMD_SPLIT_16	0x0060	/* Max 16 */
+#define  PCI_X_CMD_SPLIT_32	0x0070	/* Max 32 */
+#define  PCI_X_CMD_MAX_SPLIT	0x0070	/* Max Outstanding Split Transactions */
+#define  PCI_X_CMD_VERSION(x)	(((x) >> 12) & 3) /* Version */
+#define PCI_X_STATUS		4	/* PCI-X capabilities */
+#define  PCI_X_STATUS_DEVFN	0x000000ff	/* A copy of devfn */
+#define  PCI_X_STATUS_BUS	0x0000ff00	/* A copy of bus nr */
+#define  PCI_X_STATUS_64BIT	0x00010000	/* 64-bit device */
+#define  PCI_X_STATUS_133MHZ	0x00020000	/* 133 MHz capable */
+#define  PCI_X_STATUS_SPL_DISC	0x00040000	/* Split Completion Discarded */
+#define  PCI_X_STATUS_UNX_SPL	0x00080000	/* Unexpected Split Completion */
+#define  PCI_X_STATUS_COMPLEX	0x00100000	/* Device Complexity */
+#define  PCI_X_STATUS_MAX_READ	0x00600000	/* Designed Max Memory Read Count */
+#define  PCI_X_STATUS_MAX_SPLIT	0x03800000	/* Designed Max Outstanding Split Transactions */
+#define  PCI_X_STATUS_MAX_CUM	0x1c000000	/* Designed Max Cumulative Read Size */
+#define  PCI_X_STATUS_SPL_ERR	0x20000000	/* Rcvd Split Completion Error Msg */
+#define  PCI_X_STATUS_266MHZ	0x40000000	/* 266 MHz capable */
+#define  PCI_X_STATUS_533MHZ	0x80000000	/* 533 MHz capable */
+#define PCI_X_ECC_CSR		8	/* ECC control and status */
+#define PCI_CAP_PCIX_SIZEOF_V0	8	/* size of registers for Version 0 */
+#define PCI_CAP_PCIX_SIZEOF_V1	24	/* size for Version 1 */
+#define PCI_CAP_PCIX_SIZEOF_V2	PCI_CAP_PCIX_SIZEOF_V1	/* Same for v2 */
+
+/* PCI-X registers (Type 1 (bridge) devices) */
+
+#define PCI_X_BRIDGE_SSTATUS	2	/* Secondary Status */
+#define  PCI_X_SSTATUS_64BIT	0x0001	/* Secondary AD interface is 64 bits */
+#define  PCI_X_SSTATUS_133MHZ	0x0002	/* 133 MHz capable */
+#define  PCI_X_SSTATUS_FREQ	0x03c0	/* Secondary Bus Mode and Frequency */
+#define  PCI_X_SSTATUS_VERS	0x3000	/* PCI-X Capability Version */
+#define  PCI_X_SSTATUS_V1	0x1000	/* Mode 2, not Mode 1 */
+#define  PCI_X_SSTATUS_V2	0x2000	/* Mode 1 or Modes 1 and 2 */
+#define  PCI_X_SSTATUS_266MHZ	0x4000	/* 266 MHz capable */
+#define  PCI_X_SSTATUS_533MHZ	0x8000	/* 533 MHz capable */
+#define PCI_X_BRIDGE_STATUS	4	/* Bridge Status */
+
+/* PCI Bridge Subsystem ID registers */
+
+#define PCI_SSVID_VENDOR_ID     4	/* PCI Bridge subsystem vendor ID */
+#define PCI_SSVID_DEVICE_ID     6	/* PCI Bridge subsystem device ID */
+
+/* PCI Express capability registers */
+
+#define PCI_EXP_FLAGS		2	/* Capabilities register */
+#define PCI_EXP_FLAGS_VERS	0x000f	/* Capability version */
+#define PCI_EXP_FLAGS_TYPE	0x00f0	/* Device/Port type */
+#define  PCI_EXP_TYPE_ENDPOINT	0x0	/* Express Endpoint */
+#define  PCI_EXP_TYPE_LEG_END	0x1	/* Legacy Endpoint */
+#define  PCI_EXP_TYPE_ROOT_PORT 0x4	/* Root Port */
+#define  PCI_EXP_TYPE_UPSTREAM	0x5	/* Upstream Port */
+#define  PCI_EXP_TYPE_DOWNSTREAM 0x6	/* Downstream Port */
+#define  PCI_EXP_TYPE_PCI_BRIDGE 0x7	/* PCIe to PCI/PCI-X Bridge */
+#define  PCI_EXP_TYPE_PCIE_BRIDGE 0x8	/* PCI/PCI-X to PCIe Bridge */
+#define  PCI_EXP_TYPE_RC_END	0x9	/* Root Complex Integrated Endpoint */
+#define  PCI_EXP_TYPE_RC_EC	0xa	/* Root Complex Event Collector */
+#define PCI_EXP_FLAGS_SLOT	0x0100	/* Slot implemented */
+#define PCI_EXP_FLAGS_IRQ	0x3e00	/* Interrupt message number */
+#define PCI_EXP_DEVCAP		4	/* Device capabilities */
+#define  PCI_EXP_DEVCAP_PAYLOAD	0x00000007 /* Max_Payload_Size */
+#define  PCI_EXP_DEVCAP_PHANTOM	0x00000018 /* Phantom functions */
+#define  PCI_EXP_DEVCAP_EXT_TAG	0x00000020 /* Extended tags */
+#define  PCI_EXP_DEVCAP_L0S	0x000001c0 /* L0s Acceptable Latency */
+#define  PCI_EXP_DEVCAP_L1	0x00000e00 /* L1 Acceptable Latency */
+#define  PCI_EXP_DEVCAP_ATN_BUT	0x00001000 /* Attention Button Present */
+#define  PCI_EXP_DEVCAP_ATN_IND	0x00002000 /* Attention Indicator Present */
+#define  PCI_EXP_DEVCAP_PWR_IND	0x00004000 /* Power Indicator Present */
+#define  PCI_EXP_DEVCAP_RBER	0x00008000 /* Role-Based Error Reporting */
+#define  PCI_EXP_DEVCAP_PWR_VAL	0x03fc0000 /* Slot Power Limit Value */
+#define  PCI_EXP_DEVCAP_PWR_SCL	0x0c000000 /* Slot Power Limit Scale */
+#define  PCI_EXP_DEVCAP_FLR     0x10000000 /* Function Level Reset */
+#define PCI_EXP_DEVCTL		8	/* Device Control */
+#define  PCI_EXP_DEVCTL_CERE	0x0001	/* Correctable Error Reporting En. */
+#define  PCI_EXP_DEVCTL_NFERE	0x0002	/* Non-Fatal Error Reporting Enable */
+#define  PCI_EXP_DEVCTL_FERE	0x0004	/* Fatal Error Reporting Enable */
+#define  PCI_EXP_DEVCTL_URRE	0x0008	/* Unsupported Request Reporting En. */
+#define  PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */
+#define  PCI_EXP_DEVCTL_PAYLOAD	0x00e0	/* Max_Payload_Size */
+#define  PCI_EXP_DEVCTL_EXT_TAG	0x0100	/* Extended Tag Field Enable */
+#define  PCI_EXP_DEVCTL_PHANTOM	0x0200	/* Phantom Functions Enable */
+#define  PCI_EXP_DEVCTL_AUX_PME	0x0400	/* Auxiliary Power PM Enable */
+#define  PCI_EXP_DEVCTL_NOSNOOP_EN 0x0800  /* Enable No Snoop */
+#define  PCI_EXP_DEVCTL_READRQ	0x7000	/* Max_Read_Request_Size */
+#define  PCI_EXP_DEVCTL_READRQ_128B  0x0000 /* 128 Bytes */
+#define  PCI_EXP_DEVCTL_READRQ_256B  0x1000 /* 256 Bytes */
+#define  PCI_EXP_DEVCTL_READRQ_512B  0x2000 /* 512 Bytes */
+#define  PCI_EXP_DEVCTL_READRQ_1024B 0x3000 /* 1024 Bytes */
+#define  PCI_EXP_DEVCTL_BCR_FLR 0x8000  /* Bridge Configuration Retry / FLR */
+#define PCI_EXP_DEVSTA		10	/* Device Status */
+#define  PCI_EXP_DEVSTA_CED	0x0001	/* Correctable Error Detected */
+#define  PCI_EXP_DEVSTA_NFED	0x0002	/* Non-Fatal Error Detected */
+#define  PCI_EXP_DEVSTA_FED	0x0004	/* Fatal Error Detected */
+#define  PCI_EXP_DEVSTA_URD	0x0008	/* Unsupported Request Detected */
+#define  PCI_EXP_DEVSTA_AUXPD	0x0010	/* AUX Power Detected */
+#define  PCI_EXP_DEVSTA_TRPND	0x0020	/* Transactions Pending */
+#define PCI_EXP_LNKCAP		12	/* Link Capabilities */
+#define  PCI_EXP_LNKCAP_SLS	0x0000000f /* Supported Link Speeds */
+#define  PCI_EXP_LNKCAP_SLS_2_5GB 0x00000001 /* LNKCAP2 SLS Vector bit 0 */
+#define  PCI_EXP_LNKCAP_SLS_5_0GB 0x00000002 /* LNKCAP2 SLS Vector bit 1 */
+#define  PCI_EXP_LNKCAP_MLW	0x000003f0 /* Maximum Link Width */
+#define  PCI_EXP_LNKCAP_ASPMS	0x00000c00 /* ASPM Support */
+#define  PCI_EXP_LNKCAP_L0SEL	0x00007000 /* L0s Exit Latency */
+#define  PCI_EXP_LNKCAP_L1EL	0x00038000 /* L1 Exit Latency */
+#define  PCI_EXP_LNKCAP_CLKPM	0x00040000 /* Clock Power Management */
+#define  PCI_EXP_LNKCAP_SDERC	0x00080000 /* Surprise Down Error Reporting Capable */
+#define  PCI_EXP_LNKCAP_DLLLARC	0x00100000 /* Data Link Layer Link Active Reporting Capable */
+#define  PCI_EXP_LNKCAP_LBNC	0x00200000 /* Link Bandwidth Notification Capability */
+#define  PCI_EXP_LNKCAP_PN	0xff000000 /* Port Number */
+#define PCI_EXP_LNKCTL		16	/* Link Control */
+#define  PCI_EXP_LNKCTL_ASPMC	0x0003	/* ASPM Control */
+#define  PCI_EXP_LNKCTL_ASPM_L0S 0x0001	/* L0s Enable */
+#define  PCI_EXP_LNKCTL_ASPM_L1  0x0002	/* L1 Enable */
+#define  PCI_EXP_LNKCTL_RCB	0x0008	/* Read Completion Boundary */
+#define  PCI_EXP_LNKCTL_LD	0x0010	/* Link Disable */
+#define  PCI_EXP_LNKCTL_RL	0x0020	/* Retrain Link */
+#define  PCI_EXP_LNKCTL_CCC	0x0040	/* Common Clock Configuration */
+#define  PCI_EXP_LNKCTL_ES	0x0080	/* Extended Synch */
+#define  PCI_EXP_LNKCTL_CLKREQ_EN 0x0100 /* Enable clkreq */
+#define  PCI_EXP_LNKCTL_HAWD	0x0200	/* Hardware Autonomous Width Disable */
+#define  PCI_EXP_LNKCTL_LBMIE	0x0400	/* Link Bandwidth Management Interrupt Enable */
+#define  PCI_EXP_LNKCTL_LABIE	0x0800	/* Link Autonomous Bandwidth Interrupt Enable */
+#define PCI_EXP_LNKSTA		18	/* Link Status */
+#define  PCI_EXP_LNKSTA_CLS	0x000f	/* Current Link Speed */
+#define  PCI_EXP_LNKSTA_CLS_2_5GB 0x0001 /* Current Link Speed 2.5GT/s */
+#define  PCI_EXP_LNKSTA_CLS_5_0GB 0x0002 /* Current Link Speed 5.0GT/s */
+#define  PCI_EXP_LNKSTA_CLS_8_0GB 0x0003 /* Current Link Speed 8.0GT/s */
+#define  PCI_EXP_LNKSTA_NLW	0x03f0	/* Negotiated Link Width */
+#define  PCI_EXP_LNKSTA_NLW_X1	0x0010	/* Current Link Width x1 */
+#define  PCI_EXP_LNKSTA_NLW_X2	0x0020	/* Current Link Width x2 */
+#define  PCI_EXP_LNKSTA_NLW_X4	0x0040	/* Current Link Width x4 */
+#define  PCI_EXP_LNKSTA_NLW_X8	0x0080	/* Current Link Width x8 */
+#define  PCI_EXP_LNKSTA_NLW_SHIFT 4	/* start of NLW mask in link status */
+#define  PCI_EXP_LNKSTA_LT	0x0800	/* Link Training */
+#define  PCI_EXP_LNKSTA_SLC	0x1000	/* Slot Clock Configuration */
+#define  PCI_EXP_LNKSTA_DLLLA	0x2000	/* Data Link Layer Link Active */
+#define  PCI_EXP_LNKSTA_LBMS	0x4000	/* Link Bandwidth Management Status */
+#define  PCI_EXP_LNKSTA_LABS	0x8000	/* Link Autonomous Bandwidth Status */
+#define PCI_CAP_EXP_ENDPOINT_SIZEOF_V1	20	/* v1 endpoints end here */
+#define PCI_EXP_SLTCAP		20	/* Slot Capabilities */
+#define  PCI_EXP_SLTCAP_ABP	0x00000001 /* Attention Button Present */
+#define  PCI_EXP_SLTCAP_PCP	0x00000002 /* Power Controller Present */
+#define  PCI_EXP_SLTCAP_MRLSP	0x00000004 /* MRL Sensor Present */
+#define  PCI_EXP_SLTCAP_AIP	0x00000008 /* Attention Indicator Present */
+#define  PCI_EXP_SLTCAP_PIP	0x00000010 /* Power Indicator Present */
+#define  PCI_EXP_SLTCAP_HPS	0x00000020 /* Hot-Plug Surprise */
+#define  PCI_EXP_SLTCAP_HPC	0x00000040 /* Hot-Plug Capable */
+#define  PCI_EXP_SLTCAP_SPLV	0x00007f80 /* Slot Power Limit Value */
+#define  PCI_EXP_SLTCAP_SPLS	0x00018000 /* Slot Power Limit Scale */
+#define  PCI_EXP_SLTCAP_EIP	0x00020000 /* Electromechanical Interlock Present */
+#define  PCI_EXP_SLTCAP_NCCS	0x00040000 /* No Command Completed Support */
+#define  PCI_EXP_SLTCAP_PSN	0xfff80000 /* Physical Slot Number */
+#define PCI_EXP_SLTCTL		24	/* Slot Control */
+#define  PCI_EXP_SLTCTL_ABPE	0x0001	/* Attention Button Pressed Enable */
+#define  PCI_EXP_SLTCTL_PFDE	0x0002	/* Power Fault Detected Enable */
+#define  PCI_EXP_SLTCTL_MRLSCE	0x0004	/* MRL Sensor Changed Enable */
+#define  PCI_EXP_SLTCTL_PDCE	0x0008	/* Presence Detect Changed Enable */
+#define  PCI_EXP_SLTCTL_CCIE	0x0010	/* Command Completed Interrupt Enable */
+#define  PCI_EXP_SLTCTL_HPIE	0x0020	/* Hot-Plug Interrupt Enable */
+#define  PCI_EXP_SLTCTL_AIC	0x00c0	/* Attention Indicator Control */
+#define  PCI_EXP_SLTCTL_ATTN_IND_ON    0x0040 /* Attention Indicator on */
+#define  PCI_EXP_SLTCTL_ATTN_IND_BLINK 0x0080 /* Attention Indicator blinking */
+#define  PCI_EXP_SLTCTL_ATTN_IND_OFF   0x00c0 /* Attention Indicator off */
+#define  PCI_EXP_SLTCTL_PIC	0x0300	/* Power Indicator Control */
+#define  PCI_EXP_SLTCTL_PWR_IND_ON     0x0100 /* Power Indicator on */
+#define  PCI_EXP_SLTCTL_PWR_IND_BLINK  0x0200 /* Power Indicator blinking */
+#define  PCI_EXP_SLTCTL_PWR_IND_OFF    0x0300 /* Power Indicator off */
+#define  PCI_EXP_SLTCTL_PCC	0x0400	/* Power Controller Control */
+#define  PCI_EXP_SLTCTL_PWR_ON         0x0000 /* Power On */
+#define  PCI_EXP_SLTCTL_PWR_OFF        0x0400 /* Power Off */
+#define  PCI_EXP_SLTCTL_EIC	0x0800	/* Electromechanical Interlock Control */
+#define  PCI_EXP_SLTCTL_DLLSCE	0x1000	/* Data Link Layer State Changed Enable */
+#define PCI_EXP_SLTSTA		26	/* Slot Status */
+#define  PCI_EXP_SLTSTA_ABP	0x0001	/* Attention Button Pressed */
+#define  PCI_EXP_SLTSTA_PFD	0x0002	/* Power Fault Detected */
+#define  PCI_EXP_SLTSTA_MRLSC	0x0004	/* MRL Sensor Changed */
+#define  PCI_EXP_SLTSTA_PDC	0x0008	/* Presence Detect Changed */
+#define  PCI_EXP_SLTSTA_CC	0x0010	/* Command Completed */
+#define  PCI_EXP_SLTSTA_MRLSS	0x0020	/* MRL Sensor State */
+#define  PCI_EXP_SLTSTA_PDS	0x0040	/* Presence Detect State */
+#define  PCI_EXP_SLTSTA_EIS	0x0080	/* Electromechanical Interlock Status */
+#define  PCI_EXP_SLTSTA_DLLSC	0x0100	/* Data Link Layer State Changed */
+#define PCI_EXP_RTCTL		28	/* Root Control */
+#define  PCI_EXP_RTCTL_SECEE	0x0001	/* System Error on Correctable Error */
+#define  PCI_EXP_RTCTL_SENFEE	0x0002	/* System Error on Non-Fatal Error */
+#define  PCI_EXP_RTCTL_SEFEE	0x0004	/* System Error on Fatal Error */
+#define  PCI_EXP_RTCTL_PMEIE	0x0008	/* PME Interrupt Enable */
+#define  PCI_EXP_RTCTL_CRSSVE	0x0010	/* CRS Software Visibility Enable */
+#define PCI_EXP_RTCAP		30	/* Root Capabilities */
+#define  PCI_EXP_RTCAP_CRSVIS	0x0001	/* CRS Software Visibility capability */
+#define PCI_EXP_RTSTA		32	/* Root Status */
+#define PCI_EXP_RTSTA_PME	0x00010000 /* PME status */
+#define PCI_EXP_RTSTA_PENDING	0x00020000 /* PME pending */
+/*
+ * The Device Capabilities 2, Device Status 2, Device Control 2,
+ * Link Capabilities 2, Link Status 2, Link Control 2,
+ * Slot Capabilities 2, Slot Status 2, and Slot Control 2 registers
+ * are only present on devices with PCIe Capability version 2.
+ * Use pcie_capability_read_word() and similar interfaces to use them
+ * safely.
+ */
+#define PCI_EXP_DEVCAP2		36	/* Device Capabilities 2 */
+#define  PCI_EXP_DEVCAP2_ARI		0x00000020 /* Alternative Routing-ID */
+#define  PCI_EXP_DEVCAP2_LTR		0x00000800 /* Latency tolerance reporting */
+#define  PCI_EXP_DEVCAP2_OBFF_MASK	0x000c0000 /* OBFF support mechanism */
+#define  PCI_EXP_DEVCAP2_OBFF_MSG	0x00040000 /* New message signaling */
+#define  PCI_EXP_DEVCAP2_OBFF_WAKE	0x00080000 /* Re-use WAKE# for OBFF */
+#define PCI_EXP_DEVCTL2		40	/* Device Control 2 */
+#define  PCI_EXP_DEVCTL2_COMP_TIMEOUT	0x000f	/* Completion Timeout Value */
+#define  PCI_EXP_DEVCTL2_ARI		0x0020	/* Alternative Routing-ID */
+#define  PCI_EXP_DEVCTL2_IDO_REQ_EN	0x0100	/* Allow IDO for requests */
+#define  PCI_EXP_DEVCTL2_IDO_CMP_EN	0x0200	/* Allow IDO for completions */
+#define  PCI_EXP_DEVCTL2_LTR_EN		0x0400	/* Enable LTR mechanism */
+#define  PCI_EXP_DEVCTL2_OBFF_MSGA_EN	0x2000	/* Enable OBFF Message type A */
+#define  PCI_EXP_DEVCTL2_OBFF_MSGB_EN	0x4000	/* Enable OBFF Message type B */
+#define  PCI_EXP_DEVCTL2_OBFF_WAKE_EN	0x6000	/* OBFF using WAKE# signaling */
+#define PCI_EXP_DEVSTA2		42	/* Device Status 2 */
+#define PCI_CAP_EXP_ENDPOINT_SIZEOF_V2	44	/* v2 endpoints end here */
+#define PCI_EXP_LNKCAP2		44	/* Link Capabilities 2 */
+#define  PCI_EXP_LNKCAP2_SLS_2_5GB	0x00000002 /* Supported Speed 2.5GT/s */
+#define  PCI_EXP_LNKCAP2_SLS_5_0GB	0x00000004 /* Supported Speed 5.0GT/s */
+#define  PCI_EXP_LNKCAP2_SLS_8_0GB	0x00000008 /* Supported Speed 8.0GT/s */
+#define  PCI_EXP_LNKCAP2_CROSSLINK	0x00000100 /* Crosslink supported */
+#define PCI_EXP_LNKCTL2		48	/* Link Control 2 */
+#define PCI_EXP_LNKSTA2		50	/* Link Status 2 */
+#define PCI_EXP_SLTCAP2		52	/* Slot Capabilities 2 */
+#define PCI_EXP_SLTCTL2		56	/* Slot Control 2 */
+#define PCI_EXP_SLTSTA2		58	/* Slot Status 2 */
+
+/* Extended Capabilities (PCI-X 2.0 and Express) */
+#define PCI_EXT_CAP_ID(header)		(header & 0x0000ffff)
+#define PCI_EXT_CAP_VER(header)		((header >> 16) & 0xf)
+#define PCI_EXT_CAP_NEXT(header)	((header >> 20) & 0xffc)
+
+#define PCI_EXT_CAP_ID_ERR	0x01	/* Advanced Error Reporting */
+#define PCI_EXT_CAP_ID_VC	0x02	/* Virtual Channel Capability */
+#define PCI_EXT_CAP_ID_DSN	0x03	/* Device Serial Number */
+#define PCI_EXT_CAP_ID_PWR	0x04	/* Power Budgeting */
+#define PCI_EXT_CAP_ID_RCLD	0x05	/* Root Complex Link Declaration */
+#define PCI_EXT_CAP_ID_RCILC	0x06	/* Root Complex Internal Link Control */
+#define PCI_EXT_CAP_ID_RCEC	0x07	/* Root Complex Event Collector */
+#define PCI_EXT_CAP_ID_MFVC	0x08	/* Multi-Function VC Capability */
+#define PCI_EXT_CAP_ID_VC9	0x09	/* same as _VC */
+#define PCI_EXT_CAP_ID_RCRB	0x0A	/* Root Complex RB? */
+#define PCI_EXT_CAP_ID_VNDR	0x0B	/* Vendor-Specific */
+#define PCI_EXT_CAP_ID_CAC	0x0C	/* Config Access - obsolete */
+#define PCI_EXT_CAP_ID_ACS	0x0D	/* Access Control Services */
+#define PCI_EXT_CAP_ID_ARI	0x0E	/* Alternate Routing ID */
+#define PCI_EXT_CAP_ID_ATS	0x0F	/* Address Translation Services */
+#define PCI_EXT_CAP_ID_SRIOV	0x10	/* Single Root I/O Virtualization */
+#define PCI_EXT_CAP_ID_MRIOV	0x11	/* Multi Root I/O Virtualization */
+#define PCI_EXT_CAP_ID_MCAST	0x12	/* Multicast */
+#define PCI_EXT_CAP_ID_PRI	0x13	/* Page Request Interface */
+#define PCI_EXT_CAP_ID_AMD_XXX	0x14	/* Reserved for AMD */
+#define PCI_EXT_CAP_ID_REBAR	0x15	/* Resizable BAR */
+#define PCI_EXT_CAP_ID_DPA	0x16	/* Dynamic Power Allocation */
+#define PCI_EXT_CAP_ID_TPH	0x17	/* TPH Requester */
+#define PCI_EXT_CAP_ID_LTR	0x18	/* Latency Tolerance Reporting */
+#define PCI_EXT_CAP_ID_SECPCI	0x19	/* Secondary PCIe Capability */
+#define PCI_EXT_CAP_ID_PMUX	0x1A	/* Protocol Multiplexing */
+#define PCI_EXT_CAP_ID_PASID	0x1B	/* Process Address Space ID */
+#define PCI_EXT_CAP_ID_MAX	PCI_EXT_CAP_ID_PASID
+
+#define PCI_EXT_CAP_DSN_SIZEOF	12
+#define PCI_EXT_CAP_MCAST_ENDPOINT_SIZEOF 40
+
+/* Advanced Error Reporting */
+#define PCI_ERR_UNCOR_STATUS	4	/* Uncorrectable Error Status */
+#define  PCI_ERR_UNC_UND	0x00000001	/* Undefined */
+#define  PCI_ERR_UNC_DLP	0x00000010	/* Data Link Protocol */
+#define  PCI_ERR_UNC_SURPDN	0x00000020	/* Surprise Down */
+#define  PCI_ERR_UNC_POISON_TLP	0x00001000	/* Poisoned TLP */
+#define  PCI_ERR_UNC_FCP	0x00002000	/* Flow Control Protocol */
+#define  PCI_ERR_UNC_COMP_TIME	0x00004000	/* Completion Timeout */
+#define  PCI_ERR_UNC_COMP_ABORT	0x00008000	/* Completer Abort */
+#define  PCI_ERR_UNC_UNX_COMP	0x00010000	/* Unexpected Completion */
+#define  PCI_ERR_UNC_RX_OVER	0x00020000	/* Receiver Overflow */
+#define  PCI_ERR_UNC_MALF_TLP	0x00040000	/* Malformed TLP */
+#define  PCI_ERR_UNC_ECRC	0x00080000	/* ECRC Error Status */
+#define  PCI_ERR_UNC_UNSUP	0x00100000	/* Unsupported Request */
+#define  PCI_ERR_UNC_ACSV	0x00200000	/* ACS Violation */
+#define  PCI_ERR_UNC_INTN	0x00400000	/* internal error */
+#define  PCI_ERR_UNC_MCBTLP	0x00800000	/* MC blocked TLP */
+#define  PCI_ERR_UNC_ATOMEG	0x01000000	/* Atomic egress blocked */
+#define  PCI_ERR_UNC_TLPPRE	0x02000000	/* TLP prefix blocked */
+#define PCI_ERR_UNCOR_MASK	8	/* Uncorrectable Error Mask */
+	/* Same bits as above */
+#define PCI_ERR_UNCOR_SEVER	12	/* Uncorrectable Error Severity */
+	/* Same bits as above */
+#define PCI_ERR_COR_STATUS	16	/* Correctable Error Status */
+#define  PCI_ERR_COR_RCVR	0x00000001	/* Receiver Error Status */
+#define  PCI_ERR_COR_BAD_TLP	0x00000040	/* Bad TLP Status */
+#define  PCI_ERR_COR_BAD_DLLP	0x00000080	/* Bad DLLP Status */
+#define  PCI_ERR_COR_REP_ROLL	0x00000100	/* REPLAY_NUM Rollover */
+#define  PCI_ERR_COR_REP_TIMER	0x00001000	/* Replay Timer Timeout */
+#define  PCI_ERR_COR_ADV_NFAT	0x00002000	/* Advisory Non-Fatal */
+#define  PCI_ERR_COR_INTERNAL	0x00004000	/* Corrected Internal */
+#define  PCI_ERR_COR_LOG_OVER	0x00008000	/* Header Log Overflow */
+#define PCI_ERR_COR_MASK	20	/* Correctable Error Mask */
+	/* Same bits as above */
+#define PCI_ERR_CAP		24	/* Advanced Error Capabilities */
+#define  PCI_ERR_CAP_FEP(x)	((x) & 31)	/* First Error Pointer */
+#define  PCI_ERR_CAP_ECRC_GENC	0x00000020	/* ECRC Generation Capable */
+#define  PCI_ERR_CAP_ECRC_GENE	0x00000040	/* ECRC Generation Enable */
+#define  PCI_ERR_CAP_ECRC_CHKC	0x00000080	/* ECRC Check Capable */
+#define  PCI_ERR_CAP_ECRC_CHKE	0x00000100	/* ECRC Check Enable */
+#define PCI_ERR_HEADER_LOG	28	/* Header Log Register (16 bytes) */
+#define PCI_ERR_ROOT_COMMAND	44	/* Root Error Command */
+/* Correctable Err Reporting Enable */
+#define PCI_ERR_ROOT_CMD_COR_EN		0x00000001
+/* Non-fatal Err Reporting Enable */
+#define PCI_ERR_ROOT_CMD_NONFATAL_EN	0x00000002
+/* Fatal Err Reporting Enable */
+#define PCI_ERR_ROOT_CMD_FATAL_EN	0x00000004
+#define PCI_ERR_ROOT_STATUS	48
+#define PCI_ERR_ROOT_COR_RCV		0x00000001	/* ERR_COR Received */
+/* Multi ERR_COR Received */
+#define PCI_ERR_ROOT_MULTI_COR_RCV	0x00000002
+/* ERR_FATAL/NONFATAL Received */
+#define PCI_ERR_ROOT_UNCOR_RCV		0x00000004
+/* Multi ERR_FATAL/NONFATAL Received */
+#define PCI_ERR_ROOT_MULTI_UNCOR_RCV	0x00000008
+#define PCI_ERR_ROOT_FIRST_FATAL	0x00000010	/* First Fatal */
+#define PCI_ERR_ROOT_NONFATAL_RCV	0x00000020	/* Non-Fatal Received */
+#define PCI_ERR_ROOT_FATAL_RCV		0x00000040	/* Fatal Received */
+#define PCI_ERR_ROOT_ERR_SRC	52	/* Error Source Identification */
+
+/* Virtual Channel */
+#define PCI_VC_PORT_CAP1	4
+#define  PCI_VC_CAP1_EVCC	0x00000007	/* extended VC count */
+#define  PCI_VC_CAP1_LPEVCC	0x00000070	/* low prio extended VC count */
+#define  PCI_VC_CAP1_ARB_SIZE	0x00000c00
+#define PCI_VC_PORT_CAP2	8
+#define  PCI_VC_CAP2_32_PHASE		0x00000002
+#define  PCI_VC_CAP2_64_PHASE		0x00000004
+#define  PCI_VC_CAP2_128_PHASE		0x00000008
+#define  PCI_VC_CAP2_ARB_OFF		0xff000000
+#define PCI_VC_PORT_CTRL	12
+#define  PCI_VC_PORT_CTRL_LOAD_TABLE	0x00000001
+#define PCI_VC_PORT_STATUS	14
+#define  PCI_VC_PORT_STATUS_TABLE	0x00000001
+#define PCI_VC_RES_CAP		16
+#define  PCI_VC_RES_CAP_32_PHASE	0x00000002
+#define  PCI_VC_RES_CAP_64_PHASE	0x00000004
+#define  PCI_VC_RES_CAP_128_PHASE	0x00000008
+#define  PCI_VC_RES_CAP_128_PHASE_TB	0x00000010
+#define  PCI_VC_RES_CAP_256_PHASE	0x00000020
+#define  PCI_VC_RES_CAP_ARB_OFF		0xff000000
+#define PCI_VC_RES_CTRL		20
+#define  PCI_VC_RES_CTRL_LOAD_TABLE	0x00010000
+#define  PCI_VC_RES_CTRL_ARB_SELECT	0x000e0000
+#define  PCI_VC_RES_CTRL_ID		0x07000000
+#define  PCI_VC_RES_CTRL_ENABLE		0x80000000
+#define PCI_VC_RES_STATUS	26
+#define  PCI_VC_RES_STATUS_TABLE	0x00000001
+#define  PCI_VC_RES_STATUS_NEGO		0x00000002
+#define PCI_CAP_VC_BASE_SIZEOF		0x10
+#define PCI_CAP_VC_PER_VC_SIZEOF	0x0C
+
+/* Power Budgeting */
+#define PCI_PWR_DSR		4	/* Data Select Register */
+#define PCI_PWR_DATA		8	/* Data Register */
+#define  PCI_PWR_DATA_BASE(x)	((x) & 0xff)	    /* Base Power */
+#define  PCI_PWR_DATA_SCALE(x)	(((x) >> 8) & 3)    /* Data Scale */
+#define  PCI_PWR_DATA_PM_SUB(x)	(((x) >> 10) & 7)   /* PM Sub State */
+#define  PCI_PWR_DATA_PM_STATE(x) (((x) >> 13) & 3) /* PM State */
+#define  PCI_PWR_DATA_TYPE(x)	(((x) >> 15) & 7)   /* Type */
+#define  PCI_PWR_DATA_RAIL(x)	(((x) >> 18) & 7)   /* Power Rail */
+#define PCI_PWR_CAP		12	/* Capability */
+#define  PCI_PWR_CAP_BUDGET(x)	((x) & 1)	/* Included in system budget */
+#define PCI_EXT_CAP_PWR_SIZEOF	16
+
+/* Vendor-Specific (VSEC, PCI_EXT_CAP_ID_VNDR) */
+#define PCI_VNDR_HEADER		4	/* Vendor-Specific Header */
+#define  PCI_VNDR_HEADER_ID(x)	((x) & 0xffff)
+#define  PCI_VNDR_HEADER_REV(x)	(((x) >> 16) & 0xf)
+#define  PCI_VNDR_HEADER_LEN(x)	(((x) >> 20) & 0xfff)
+
+/*
+ * HyperTransport sub capability types
+ *
+ * Unfortunately there are both 3 bit and 5 bit capability types defined
+ * in the HT spec, catering for that is a little messy. You probably don't
+ * want to use these directly, just use pci_find_ht_capability() and it
+ * will do the right thing for you.
+ */
+#define HT_3BIT_CAP_MASK	0xE0
+#define HT_CAPTYPE_SLAVE	0x00	/* Slave/Primary link configuration */
+#define HT_CAPTYPE_HOST		0x20	/* Host/Secondary link configuration */
+
+#define HT_5BIT_CAP_MASK	0xF8
+#define HT_CAPTYPE_IRQ		0x80	/* IRQ Configuration */
+#define HT_CAPTYPE_REMAPPING_40	0xA0	/* 40 bit address remapping */
+#define HT_CAPTYPE_REMAPPING_64 0xA2	/* 64 bit address remapping */
+#define HT_CAPTYPE_UNITID_CLUMP	0x90	/* Unit ID clumping */
+#define HT_CAPTYPE_EXTCONF	0x98	/* Extended Configuration Space Access */
+#define HT_CAPTYPE_MSI_MAPPING	0xA8	/* MSI Mapping Capability */
+#define  HT_MSI_FLAGS		0x02		/* Offset to flags */
+#define  HT_MSI_FLAGS_ENABLE	0x1		/* Mapping enable */
+#define  HT_MSI_FLAGS_FIXED	0x2		/* Fixed mapping only */
+#define  HT_MSI_FIXED_ADDR	0x00000000FEE00000ULL	/* Fixed addr */
+#define  HT_MSI_ADDR_LO		0x04		/* Offset to low addr bits */
+#define  HT_MSI_ADDR_LO_MASK	0xFFF00000	/* Low address bit mask */
+#define  HT_MSI_ADDR_HI		0x08		/* Offset to high addr bits */
+#define HT_CAPTYPE_DIRECT_ROUTE	0xB0	/* Direct routing configuration */
+#define HT_CAPTYPE_VCSET	0xB8	/* Virtual Channel configuration */
+#define HT_CAPTYPE_ERROR_RETRY	0xC0	/* Retry on error configuration */
+#define HT_CAPTYPE_GEN3		0xD0	/* Generation 3 HyperTransport configuration */
+#define HT_CAPTYPE_PM		0xE0	/* HyperTransport power management configuration */
+#define HT_CAP_SIZEOF_LONG	28	/* slave & primary */
+#define HT_CAP_SIZEOF_SHORT	24	/* host & secondary */
+
+/* Alternative Routing-ID Interpretation */
+#define PCI_ARI_CAP		0x04	/* ARI Capability Register */
+#define  PCI_ARI_CAP_MFVC	0x0001	/* MFVC Function Groups Capability */
+#define  PCI_ARI_CAP_ACS	0x0002	/* ACS Function Groups Capability */
+#define  PCI_ARI_CAP_NFN(x)	(((x) >> 8) & 0xff) /* Next Function Number */
+#define PCI_ARI_CTRL		0x06	/* ARI Control Register */
+#define  PCI_ARI_CTRL_MFVC	0x0001	/* MFVC Function Groups Enable */
+#define  PCI_ARI_CTRL_ACS	0x0002	/* ACS Function Groups Enable */
+#define  PCI_ARI_CTRL_FG(x)	(((x) >> 4) & 7) /* Function Group */
+#define PCI_EXT_CAP_ARI_SIZEOF	8
+
+/* Address Translation Service */
+#define PCI_ATS_CAP		0x04	/* ATS Capability Register */
+#define  PCI_ATS_CAP_QDEP(x)	((x) & 0x1f)	/* Invalidate Queue Depth */
+#define  PCI_ATS_MAX_QDEP	32	/* Max Invalidate Queue Depth */
+#define PCI_ATS_CTRL		0x06	/* ATS Control Register */
+#define  PCI_ATS_CTRL_ENABLE	0x8000	/* ATS Enable */
+#define  PCI_ATS_CTRL_STU(x)	((x) & 0x1f)	/* Smallest Translation Unit */
+#define  PCI_ATS_MIN_STU	12	/* shift of minimum STU block */
+#define PCI_EXT_CAP_ATS_SIZEOF	8
+
+/* Page Request Interface */
+#define PCI_PRI_CTRL		0x04	/* PRI control register */
+#define  PCI_PRI_CTRL_ENABLE	0x01	/* Enable */
+#define  PCI_PRI_CTRL_RESET	0x02	/* Reset */
+#define PCI_PRI_STATUS		0x06	/* PRI status register */
+#define  PCI_PRI_STATUS_RF	0x001	/* Response Failure */
+#define  PCI_PRI_STATUS_UPRGI	0x002	/* Unexpected PRG index */
+#define  PCI_PRI_STATUS_STOPPED	0x100	/* PRI Stopped */
+#define PCI_PRI_MAX_REQ		0x08	/* PRI max reqs supported */
+#define PCI_PRI_ALLOC_REQ	0x0c	/* PRI max reqs allowed */
+#define PCI_EXT_CAP_PRI_SIZEOF	16
+
+/* Process Address Space ID */
+#define PCI_PASID_CAP		0x04    /* PASID feature register */
+#define  PCI_PASID_CAP_EXEC	0x02	/* Exec permissions Supported */
+#define  PCI_PASID_CAP_PRIV	0x04	/* Privilege Mode Supported */
+#define PCI_PASID_CTRL		0x06    /* PASID control register */
+#define  PCI_PASID_CTRL_ENABLE	0x01	/* Enable bit */
+#define  PCI_PASID_CTRL_EXEC	0x02	/* Exec permissions Enable */
+#define  PCI_PASID_CTRL_PRIV	0x04	/* Privilege Mode Enable */
+#define PCI_EXT_CAP_PASID_SIZEOF	8
+
+/* Single Root I/O Virtualization */
+#define PCI_SRIOV_CAP		0x04	/* SR-IOV Capabilities */
+#define  PCI_SRIOV_CAP_VFM	0x01	/* VF Migration Capable */
+#define  PCI_SRIOV_CAP_INTR(x)	((x) >> 21) /* Interrupt Message Number */
+#define PCI_SRIOV_CTRL		0x08	/* SR-IOV Control */
+#define  PCI_SRIOV_CTRL_VFE	0x01	/* VF Enable */
+#define  PCI_SRIOV_CTRL_VFM	0x02	/* VF Migration Enable */
+#define  PCI_SRIOV_CTRL_INTR	0x04	/* VF Migration Interrupt Enable */
+#define  PCI_SRIOV_CTRL_MSE	0x08	/* VF Memory Space Enable */
+#define  PCI_SRIOV_CTRL_ARI	0x10	/* ARI Capable Hierarchy */
+#define PCI_SRIOV_STATUS	0x0a	/* SR-IOV Status */
+#define  PCI_SRIOV_STATUS_VFM	0x01	/* VF Migration Status */
+#define PCI_SRIOV_INITIAL_VF	0x0c	/* Initial VFs */
+#define PCI_SRIOV_TOTAL_VF	0x0e	/* Total VFs */
+#define PCI_SRIOV_NUM_VF	0x10	/* Number of VFs */
+#define PCI_SRIOV_FUNC_LINK	0x12	/* Function Dependency Link */
+#define PCI_SRIOV_VF_OFFSET	0x14	/* First VF Offset */
+#define PCI_SRIOV_VF_STRIDE	0x16	/* Following VF Stride */
+#define PCI_SRIOV_VF_DID	0x1a	/* VF Device ID */
+#define PCI_SRIOV_SUP_PGSIZE	0x1c	/* Supported Page Sizes */
+#define PCI_SRIOV_SYS_PGSIZE	0x20	/* System Page Size */
+#define PCI_SRIOV_BAR		0x24	/* VF BAR0 */
+#define  PCI_SRIOV_NUM_BARS	6	/* Number of VF BARs */
+#define PCI_SRIOV_VFM		0x3c	/* VF Migration State Array Offset*/
+#define  PCI_SRIOV_VFM_BIR(x)	((x) & 7)	/* State BIR */
+#define  PCI_SRIOV_VFM_OFFSET(x) ((x) & ~7)	/* State Offset */
+#define  PCI_SRIOV_VFM_UA	0x0	/* Inactive.Unavailable */
+#define  PCI_SRIOV_VFM_MI	0x1	/* Dormant.MigrateIn */
+#define  PCI_SRIOV_VFM_MO	0x2	/* Active.MigrateOut */
+#define  PCI_SRIOV_VFM_AV	0x3	/* Active.Available */
+#define PCI_EXT_CAP_SRIOV_SIZEOF 64
+
+#define PCI_LTR_MAX_SNOOP_LAT	0x4
+#define PCI_LTR_MAX_NOSNOOP_LAT	0x6
+#define  PCI_LTR_VALUE_MASK	0x000003ff
+#define  PCI_LTR_SCALE_MASK	0x00001c00
+#define  PCI_LTR_SCALE_SHIFT	10
+#define PCI_EXT_CAP_LTR_SIZEOF	8
+
+/* Access Control Service */
+#define PCI_ACS_CAP		0x04	/* ACS Capability Register */
+#define  PCI_ACS_SV		0x01	/* Source Validation */
+#define  PCI_ACS_TB		0x02	/* Translation Blocking */
+#define  PCI_ACS_RR		0x04	/* P2P Request Redirect */
+#define  PCI_ACS_CR		0x08	/* P2P Completion Redirect */
+#define  PCI_ACS_UF		0x10	/* Upstream Forwarding */
+#define  PCI_ACS_EC		0x20	/* P2P Egress Control */
+#define  PCI_ACS_DT		0x40	/* Direct Translated P2P */
+#define PCI_ACS_EGRESS_BITS	0x05	/* ACS Egress Control Vector Size */
+#define PCI_ACS_CTRL		0x06	/* ACS Control Register */
+#define PCI_ACS_EGRESS_CTL_V	0x08	/* ACS Egress Control Vector */
+
+#define PCI_VSEC_HDR		4	/* extended cap - vendor-specific */
+#define  PCI_VSEC_HDR_LEN_SHIFT	20	/* shift for length field */
+
+/* SATA capability */
+#define PCI_SATA_REGS		4	/* SATA REGs specifier */
+#define  PCI_SATA_REGS_MASK	0xF	/* location - BAR#/inline */
+#define  PCI_SATA_REGS_INLINE	0xF	/* REGS in config space */
+#define PCI_SATA_SIZEOF_SHORT	8
+#define PCI_SATA_SIZEOF_LONG	16
+
+/* Resizable BARs */
+#define PCI_REBAR_CTRL		8	/* control register */
+#define  PCI_REBAR_CTRL_NBAR_MASK	(7 << 5)	/* mask for # bars */
+#define  PCI_REBAR_CTRL_NBAR_SHIFT	5	/* shift for # bars */
+
+/* Dynamic Power Allocation */
+#define PCI_DPA_CAP		4	/* capability register */
+#define  PCI_DPA_CAP_SUBSTATE_MASK	0x1F	/* # substates - 1 */
+#define PCI_DPA_BASE_SIZEOF	16	/* size with 0 substates */
+
+/* TPH Requester */
+#define PCI_TPH_CAP		4	/* capability register */
+#define  PCI_TPH_CAP_LOC_MASK	0x600	/* location mask */
+#define   PCI_TPH_LOC_NONE	0x000	/* no location */
+#define   PCI_TPH_LOC_CAP	0x200	/* in capability */
+#define   PCI_TPH_LOC_MSIX	0x400	/* in MSI-X */
+#define PCI_TPH_CAP_ST_MASK	0x07FF0000	/* st table mask */
+#define PCI_TPH_CAP_ST_SHIFT	16	/* st table shift */
+#define PCI_TPH_BASE_SIZEOF	12	/* size with no st table */
 
 #endif /* LINUX_PCI_REGS_H */
-- 
2.1.4


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  parent reply	other threads:[~2015-03-17  6:39 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-03-17  6:38 i.MX6 PCI support Sascha Hauer
2015-03-17  6:38 ` [PATCH 1/7] pci: Use standard pr_debug Sascha Hauer
2015-03-18  9:08   ` Jean-Christophe PLAGNIOL-VILLARD
2015-03-17  6:38 ` [PATCH 2/7] pci: fix copy-paste bug Sascha Hauer
2015-03-17  6:38 ` Sascha Hauer [this message]
2015-03-17  6:38 ` [PATCH 4/7] pci: Add pcie-designware driver Sascha Hauer
2015-03-17  6:38 ` [PATCH 5/7] ARM: i.MX: Add imx_clk_gate_exclusive Sascha Hauer
2015-03-17  6:38 ` [PATCH 6/7] ARM: i.MX6: Add PCI clocks Sascha Hauer
2015-03-17  6:38 ` [PATCH 7/7] pci: Add i.MX6 pcie support Sascha Hauer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1426574331-22797-4-git-send-email-s.hauer@pengutronix.de \
    --to=s.hauer@pengutronix.de \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox