* [PATCH v2 1/8] mtd: spi-nor: add SPI-NOR framework
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
@ 2015-05-28 15:56 ` Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 2/8] mtd: spi-nor: add cadence quadspi driver Steffen Trumtrar
` (7 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-28 15:56 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar, Enrico Jorns
Import the SPI-NOR framework from linux kernel v3.19.
Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
drivers/mtd/Kconfig | 1 +
drivers/mtd/Makefile | 1 +
drivers/mtd/spi-nor/Kconfig | 6 +
drivers/mtd/spi-nor/Makefile | 1 +
drivers/mtd/spi-nor/spi-nor.c | 1148 +++++++++++++++++++++++++++++++++++++++
include/linux/mod_devicetable.h | 7 +
include/linux/mtd/spi-nor.h | 204 +++++++
7 files changed, 1368 insertions(+)
create mode 100644 drivers/mtd/spi-nor/Kconfig
create mode 100644 drivers/mtd/spi-nor/Makefile
create mode 100644 drivers/mtd/spi-nor/spi-nor.c
create mode 100644 include/linux/mtd/spi-nor.h
diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig
index e94e6b1f63bb..49ea88cac430 100644
--- a/drivers/mtd/Kconfig
+++ b/drivers/mtd/Kconfig
@@ -23,6 +23,7 @@ config MTD_RAW_DEVICE
source "drivers/mtd/devices/Kconfig"
source "drivers/mtd/nor/Kconfig"
source "drivers/mtd/nand/Kconfig"
+source "drivers/mtd/spi-nor/Kconfig"
source "drivers/mtd/ubi/Kconfig"
endif
diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
index 9c7725742e6f..148ec6ca23b1 100644
--- a/drivers/mtd/Makefile
+++ b/drivers/mtd/Makefile
@@ -1,5 +1,6 @@
obj-$(CONFIG_NAND) += nand/
obj-$(CONFIG_DRIVER_CFI) += nor/
+obj-$(CONFIG_MTD_SPI_NOR) += spi-nor/
obj-$(CONFIG_MTD_UBI) += ubi/
obj-y += devices/
obj-$(CONFIG_MTD) += core.o partition.o
diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
new file mode 100644
index 000000000000..1568b2fb6d69
--- /dev/null
+++ b/drivers/mtd/spi-nor/Kconfig
@@ -0,0 +1,6 @@
+menuconfig MTD_SPI_NOR
+ tristate "SPI-NOR device support"
+ depends on MTD
+ help
+ This is the framework for the SPI NOR which can be used by the SPI
+ device drivers and the SPI-NOR device driver.
diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
new file mode 100644
index 000000000000..fe88e3d86ee5
--- /dev/null
+++ b/drivers/mtd/spi-nor/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_MTD_SPI_NOR) += spi-nor.o
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
new file mode 100644
index 000000000000..c85ed34e06f9
--- /dev/null
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -0,0 +1,1148 @@
+/*
+ * Based on m25p80.c, by Mike Lavender (mike@steroidmicros.com), with
+ * influence from lart.c (Abraham Van Der Merwe) and mtd_dataflash.c
+ *
+ * Copyright (C) 2005, Intec Automation Inc.
+ * Copyright (C) 2014, Freescale Semiconductor, Inc.
+ *
+ * This code is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <clock.h>
+#include <common.h>
+#include <driver.h>
+#include <errno.h>
+#include <linux/err.h>
+#include <linux/math64.h>
+#include <linux/mod_devicetable.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/spi-nor.h>
+#include <of.h>
+#include <spi/flash.h>
+
+#define SPI_NOR_MAX_ID_LEN 6
+
+struct flash_info {
+ /*
+ * This array stores the ID bytes.
+ * The first three bytes are the JEDIC ID.
+ * JEDEC ID zero means "no ID" (mostly older chips).
+ */
+ u8 id[SPI_NOR_MAX_ID_LEN];
+ u8 id_len;
+
+ /* The size listed here is what works with SPINOR_OP_SE, which isn't
+ * necessarily called a "sector" by the vendor.
+ */
+ unsigned sector_size;
+ u16 n_sectors;
+
+ u16 page_size;
+ u16 addr_width;
+
+ u16 flags;
+#define SECT_4K 0x01 /* SPINOR_OP_BE_4K works uniformly */
+#define SPI_NOR_NO_ERASE 0x02 /* No erase command needed */
+#define SST_WRITE 0x04 /* use SST byte programming */
+#define SPI_NOR_NO_FR 0x08 /* Can't do fastread */
+#define SECT_4K_PMC 0x10 /* SPINOR_OP_BE_4K_PMC works uniformly */
+#define SPI_NOR_DUAL_READ 0x20 /* Flash supports Dual Read */
+#define SPI_NOR_QUAD_READ 0x40 /* Flash supports Quad Read */
+#define USE_FSR 0x80 /* use flag status register */
+};
+
+#define JEDEC_MFR(info) ((info)->id[0])
+
+static const struct spi_device_id *spi_nor_match_id(const char *name);
+
+/*
+ * Read the status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_sr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDSR, &val, 1);
+ if (ret < 0) {
+ pr_err("error %d reading SR\n", (int) ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
+ * Read the flag status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_fsr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDFSR, &val, 1);
+ if (ret < 0) {
+ pr_err("error %d reading FSR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
+ * Read configuration register, returning its value in the
+ * location. Return the configuration register value.
+ * Returns negative if error occured.
+ */
+static int read_cr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDCR, &val, 1);
+ if (ret < 0) {
+ dev_err(nor->dev, "error %d reading CR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
+ * Dummy Cycle calculation for different type of read.
+ * It can be used to support more commands with
+ * different dummy cycle requirements.
+ */
+static inline int spi_nor_read_dummy_cycles(struct spi_nor *nor)
+{
+ switch (nor->flash_read) {
+ case SPI_NOR_FAST:
+ case SPI_NOR_DUAL:
+ case SPI_NOR_QUAD:
+ return 8;
+ case SPI_NOR_NORMAL:
+ return 0;
+ }
+ return 0;
+}
+
+/*
+ * Write status register 1 byte
+ * Returns negative if error occurred.
+ */
+static inline int write_sr(struct spi_nor *nor, u8 val)
+{
+ nor->cmd_buf[0] = val;
+ return nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1, 0);
+}
+
+/*
+ * Set write enable latch with Write Enable command.
+ * Returns negative if error occurred.
+ */
+static inline int write_enable(struct spi_nor *nor)
+{
+ return nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0, 0);
+}
+
+/*
+ * Send write disble instruction to the chip.
+ */
+static inline int write_disable(struct spi_nor *nor)
+{
+ return nor->write_reg(nor, SPINOR_OP_WRDI, NULL, 0, 0);
+}
+
+static inline struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
+{
+ return mtd->priv;
+}
+
+/* Enable/disable 4-byte addressing mode. */
+static inline int set_4byte(struct spi_nor *nor, struct flash_info *info,
+ int enable)
+{
+ int status;
+ bool need_wren = false;
+ u8 cmd;
+
+ switch (JEDEC_MFR(info)) {
+ case CFI_MFR_ST: /* Micron, actually */
+ /* Some Micron need WREN command; all will accept it */
+ need_wren = true;
+ case CFI_MFR_MACRONIX:
+ case 0xEF /* winbond */:
+ if (need_wren)
+ write_enable(nor);
+
+ cmd = enable ? SPINOR_OP_EN4B : SPINOR_OP_EX4B;
+ status = nor->write_reg(nor, cmd, NULL, 0, 0);
+ if (need_wren)
+ write_disable(nor);
+
+ return status;
+ default:
+ /* Spansion style */
+ nor->cmd_buf[0] = enable << 7;
+ return nor->write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1, 0);
+ }
+}
+static inline int spi_nor_sr_ready(struct spi_nor *nor)
+{
+ int sr = read_sr(nor);
+ if (sr < 0)
+ return sr;
+ else
+ return !(sr & SR_WIP);
+}
+
+static inline int spi_nor_fsr_ready(struct spi_nor *nor)
+{
+ int fsr = read_fsr(nor);
+ if (fsr < 0)
+ return fsr;
+ else
+ return fsr & FSR_READY;
+}
+
+static int spi_nor_ready(struct spi_nor *nor)
+{
+ int sr, fsr;
+ sr = spi_nor_sr_ready(nor);
+ if (sr < 0)
+ return sr;
+ fsr = nor->flags & SNOR_F_USE_FSR ? spi_nor_fsr_ready(nor) : 1;
+ if (fsr < 0)
+ return fsr;
+ return sr && fsr;
+}
+
+/*
+ * Service routine to read status register until ready, or timeout occurs.
+ * Returns non-zero if error.
+ */
+static int spi_nor_wait_till_ready(struct spi_nor *nor)
+{
+ uint64_t start = get_time_ns();
+ int timeout = 0;
+ int ret;
+
+ while (!timeout) {
+ if (is_timeout(start, 40 * SECOND))
+ timeout = 1;
+
+ ret = spi_nor_ready(nor);
+ if (ret < 0)
+ return ret;
+ if (ret)
+ return 0;
+ }
+
+ dev_err(nor->dev, "flash operation timed out\n");
+
+ return -ETIMEDOUT;
+}
+
+/*
+ * Erase the whole flash memory
+ *
+ * Returns 0 if successful, non-zero otherwise.
+ */
+static int erase_chip(struct spi_nor *nor)
+{
+ dev_dbg(nor->dev, " %lldKiB\n", (long long)(nor->mtd->size >> 10));
+
+ return nor->write_reg(nor, SPINOR_OP_CHIP_ERASE, NULL, 0, 0);
+}
+
+static int spi_nor_lock_and_prep(struct spi_nor *nor, enum spi_nor_ops ops)
+{
+ int ret = 0;
+
+ mutex_lock(&nor->lock);
+
+ if (nor->prepare) {
+ ret = nor->prepare(nor, ops);
+ if (ret) {
+ dev_err(nor->dev, "failed in the preparation.\n");
+ mutex_unlock(&nor->lock);
+ return ret;
+ }
+ }
+ return ret;
+}
+
+static void spi_nor_unlock_and_unprep(struct spi_nor *nor, enum spi_nor_ops ops)
+{
+ if (nor->unprepare)
+ nor->unprepare(nor, ops);
+ mutex_unlock(&nor->lock);
+}
+
+/*
+ * Erase an address range on the nor chip. The address range may extend
+ * one or more erase sectors. Return an error is there is a problem erasing.
+ */
+static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ u32 addr, len;
+ uint32_t rem;
+ int ret;
+
+ dev_dbg(nor->dev, "at 0x%llx, len %lld\n", (long long)instr->addr,
+ (long long)instr->len);
+
+ div_u64_rem(instr->len, mtd->erasesize, &rem);
+ if (rem)
+ return -EINVAL;
+
+ addr = instr->addr;
+ len = instr->len;
+
+ /* Assure previous operations are completed */
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto erase_err;
+
+ ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_ERASE);
+ if (ret)
+ return ret;
+
+ /* whole-chip erase? */
+ if (len == mtd->size) {
+ write_enable(nor);
+
+ if (erase_chip(nor)) {
+ ret = -EIO;
+ goto erase_err;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto erase_err;
+
+ /* REVISIT in some cases we could speed up erasing large regions
+ * by using SPINOR_OP_SE instead of SPINOR_OP_BE_4K. We may have set up
+ * to use "small sector erase", but that's not always optimal.
+ */
+
+ /* "sector"-at-a-time erase */
+ } else {
+ while (len) {
+ write_enable(nor);
+
+ if (nor->erase(nor, addr)) {
+ ret = -EIO;
+ goto erase_err;
+ }
+
+ addr += mtd->erasesize;
+ len -= mtd->erasesize;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto erase_err;
+ }
+ }
+
+ write_disable(nor);
+
+ spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_ERASE);
+
+ instr->state = MTD_ERASE_DONE;
+ mtd_erase_callback(instr);
+
+ return ret;
+
+erase_err:
+ spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_ERASE);
+ instr->state = MTD_ERASE_FAILED;
+ return ret;
+}
+
+static int spi_nor_lock(struct mtd_info *mtd, loff_t ofs, size_t len)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ uint32_t offset = ofs;
+ uint8_t status_old, status_new;
+ int ret = 0;
+
+ ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_LOCK);
+ if (ret)
+ return ret;
+
+ status_old = read_sr(nor);
+
+ if (offset < mtd->size - (mtd->size / 2))
+ status_new = status_old | SR_BP2 | SR_BP1 | SR_BP0;
+ else if (offset < mtd->size - (mtd->size / 4))
+ status_new = (status_old & ~SR_BP0) | SR_BP2 | SR_BP1;
+ else if (offset < mtd->size - (mtd->size / 8))
+ status_new = (status_old & ~SR_BP1) | SR_BP2 | SR_BP0;
+ else if (offset < mtd->size - (mtd->size / 16))
+ status_new = (status_old & ~(SR_BP0 | SR_BP1)) | SR_BP2;
+ else if (offset < mtd->size - (mtd->size / 32))
+ status_new = (status_old & ~SR_BP2) | SR_BP1 | SR_BP0;
+ else if (offset < mtd->size - (mtd->size / 64))
+ status_new = (status_old & ~(SR_BP2 | SR_BP0)) | SR_BP1;
+ else
+ status_new = (status_old & ~(SR_BP2 | SR_BP1)) | SR_BP0;
+
+ /* Only modify protection if it will not unlock other areas */
+ if ((status_new & (SR_BP2 | SR_BP1 | SR_BP0)) >
+ (status_old & (SR_BP2 | SR_BP1 | SR_BP0))) {
+ write_enable(nor);
+ ret = write_sr(nor, status_new);
+ if (ret)
+ goto err;
+ }
+
+err:
+ spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_LOCK);
+ return ret;
+}
+
+static int spi_nor_unlock(struct mtd_info *mtd, loff_t ofs, size_t len)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ uint32_t offset = ofs;
+ uint8_t status_old, status_new;
+ int ret = 0;
+
+ ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_UNLOCK);
+ if (ret)
+ return ret;
+
+ status_old = read_sr(nor);
+
+ if (offset+len > mtd->size - (mtd->size / 64))
+ status_new = status_old & ~(SR_BP2 | SR_BP1 | SR_BP0);
+ else if (offset+len > mtd->size - (mtd->size / 32))
+ status_new = (status_old & ~(SR_BP2 | SR_BP1)) | SR_BP0;
+ else if (offset+len > mtd->size - (mtd->size / 16))
+ status_new = (status_old & ~(SR_BP2 | SR_BP0)) | SR_BP1;
+ else if (offset+len > mtd->size - (mtd->size / 8))
+ status_new = (status_old & ~SR_BP2) | SR_BP1 | SR_BP0;
+ else if (offset+len > mtd->size - (mtd->size / 4))
+ status_new = (status_old & ~(SR_BP0 | SR_BP1)) | SR_BP2;
+ else if (offset+len > mtd->size - (mtd->size / 2))
+ status_new = (status_old & ~SR_BP1) | SR_BP2 | SR_BP0;
+ else
+ status_new = (status_old & ~SR_BP0) | SR_BP2 | SR_BP1;
+
+ /* Only modify protection if it will not lock other areas */
+ if ((status_new & (SR_BP2 | SR_BP1 | SR_BP0)) <
+ (status_old & (SR_BP2 | SR_BP1 | SR_BP0))) {
+ write_enable(nor);
+ ret = write_sr(nor, status_new);
+ if (ret)
+ goto err;
+ }
+
+err:
+ spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_UNLOCK);
+ return ret;
+}
+
+/* Used when the "_ext_id" is two bytes at most */
+#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
+ ((unsigned long)&(struct flash_info) { \
+ .id = { \
+ ((_jedec_id) >> 16) & 0xff, \
+ ((_jedec_id) >> 8) & 0xff, \
+ (_jedec_id) & 0xff, \
+ ((_ext_id) >> 8) & 0xff, \
+ (_ext_id) & 0xff, \
+ }, \
+ .id_len = (!(_jedec_id) ? 0 : (3 + ((_ext_id) ? 2 : 0))), \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = 256, \
+ .flags = (_flags), \
+ })
+
+#define INFO6(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
+ ((unsigned long)&(struct flash_info) { \
+ .id = { \
+ ((_jedec_id) >> 16) & 0xff, \
+ ((_jedec_id) >> 8) & 0xff, \
+ (_jedec_id) & 0xff, \
+ ((_ext_id) >> 16) & 0xff, \
+ ((_ext_id) >> 8) & 0xff, \
+ (_ext_id) & 0xff, \
+ }, \
+ .id_len = 6, \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = 256, \
+ .flags = (_flags), \
+ })
+
+#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width, _flags) \
+ ((unsigned long)&(struct flash_info) { \
+ .sector_size = (_sector_size), \
+ .n_sectors = (_n_sectors), \
+ .page_size = (_page_size), \
+ .addr_width = (_addr_width), \
+ .flags = (_flags), \
+ })
+
+/* NOTE: double check command sets and memory organization when you add
+ * more nor chips. This current list focusses on newer chips, which
+ * have been converging on command sets which including JEDEC ID.
+ */
+static const struct spi_device_id spi_nor_ids[] = {
+ /* Atmel -- some are (confusingly) marketed as "DataFlash" */
+ { "at25fs010", INFO(0x1f6601, 0, 32 * 1024, 4, SECT_4K) },
+ { "at25fs040", INFO(0x1f6604, 0, 64 * 1024, 8, SECT_4K) },
+
+ { "at25df041a", INFO(0x1f4401, 0, 64 * 1024, 8, SECT_4K) },
+ { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
+ { "at25df641", INFO(0x1f4800, 0, 64 * 1024, 128, SECT_4K) },
+
+ { "at26f004", INFO(0x1f0400, 0, 64 * 1024, 8, SECT_4K) },
+ { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
+ { "at26df161a", INFO(0x1f4601, 0, 64 * 1024, 32, SECT_4K) },
+ { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
+
+ { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
+
+ /* EON -- en25xxx */
+ { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) },
+ { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) },
+ { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) },
+ { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) },
+ { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
+ { "en25qh128", INFO(0x1c7018, 0, 64 * 1024, 256, 0) },
+ { "en25qh256", INFO(0x1c7019, 0, 64 * 1024, 512, 0) },
+
+ /* ESMT */
+ { "f25l32pa", INFO(0x8c2016, 0, 64 * 1024, 64, SECT_4K) },
+
+ /* Everspin */
+ { "mr25h256", CAT25_INFO( 32 * 1024, 1, 256, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
+ { "mr25h10", CAT25_INFO(128 * 1024, 1, 256, 3, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
+
+ /* Fujitsu */
+ { "mb85rs1mt", INFO(0x047f27, 0, 128 * 1024, 1, SPI_NOR_NO_ERASE) },
+
+ /* GigaDevice */
+ { "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64, SECT_4K) },
+ { "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128, SECT_4K) },
+
+ /* Intel/Numonyx -- xxxs33b */
+ { "160s33b", INFO(0x898911, 0, 64 * 1024, 32, 0) },
+ { "320s33b", INFO(0x898912, 0, 64 * 1024, 64, 0) },
+ { "640s33b", INFO(0x898913, 0, 64 * 1024, 128, 0) },
+
+ /* Macronix */
+ { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) },
+ { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) },
+ { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) },
+ { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) },
+ { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, 0) },
+ { "mx25l3255e", INFO(0xc29e16, 0, 64 * 1024, 64, SECT_4K) },
+ { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, 0) },
+ { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
+ { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
+ { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) },
+ { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
+ { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_QUAD_READ) },
+ { "mx66l1g55g", INFO(0xc2261b, 0, 64 * 1024, 2048, SPI_NOR_QUAD_READ) },
+
+ /* Micron */
+ { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, 0) },
+ { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
+ { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) },
+ { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) },
+ { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K) },
+ { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, USE_FSR) },
+ { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, USE_FSR | SPI_NOR_QUAD_READ) },
+
+ /* PMC */
+ { "pm25lv512", INFO(0, 0, 32 * 1024, 2, SECT_4K_PMC) },
+ { "pm25lv010", INFO(0, 0, 32 * 1024, 4, SECT_4K_PMC) },
+ { "pm25lq032", INFO(0x7f9d46, 0, 64 * 1024, 64, SECT_4K) },
+
+ /* Spansion -- single (large) sector size only, at least
+ * for the chips listed here (without boot sectors).
+ */
+ { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, 0) },
+ { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, 0) },
+ { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s25fl512s", INFO(0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "s70fl01gs", INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) },
+ { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
+ { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
+ { "s25fl128s", INFO6(0x012018, 0x4d0180, 64 * 1024, 256, SPI_NOR_QUAD_READ) },
+ { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, 0) },
+ { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, 0) },
+ { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) },
+ { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
+ { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
+ { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) },
+ { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) },
+ { "s25fl008k", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
+ { "s25fl016k", INFO(0xef4015, 0, 64 * 1024, 32, SECT_4K) },
+ { "s25fl064k", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
+ { "s25fl132k", INFO(0x014016, 0, 64 * 1024, 64, 0) },
+
+ /* SST -- large erase sizes are "overlays", "sectors" are 4K */
+ { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
+ { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+ { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) },
+ { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) },
+ { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) },
+ { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) },
+ { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) },
+ { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) },
+ { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) },
+ { "sst25wf080", INFO(0xbf2505, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+
+ /* ST Microelectronics -- newer production may have feature updates */
+ { "m25p05", INFO(0x202010, 0, 32 * 1024, 2, 0) },
+ { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) },
+ { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) },
+ { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) },
+ { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) },
+ { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) },
+ { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) },
+ { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) },
+ { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) },
+
+ { "m25p05-nonjedec", INFO(0, 0, 32 * 1024, 2, 0) },
+ { "m25p10-nonjedec", INFO(0, 0, 32 * 1024, 4, 0) },
+ { "m25p20-nonjedec", INFO(0, 0, 64 * 1024, 4, 0) },
+ { "m25p40-nonjedec", INFO(0, 0, 64 * 1024, 8, 0) },
+ { "m25p80-nonjedec", INFO(0, 0, 64 * 1024, 16, 0) },
+ { "m25p16-nonjedec", INFO(0, 0, 64 * 1024, 32, 0) },
+ { "m25p32-nonjedec", INFO(0, 0, 64 * 1024, 64, 0) },
+ { "m25p64-nonjedec", INFO(0, 0, 64 * 1024, 128, 0) },
+ { "m25p128-nonjedec", INFO(0, 0, 256 * 1024, 64, 0) },
+
+ { "m45pe10", INFO(0x204011, 0, 64 * 1024, 2, 0) },
+ { "m45pe80", INFO(0x204014, 0, 64 * 1024, 16, 0) },
+ { "m45pe16", INFO(0x204015, 0, 64 * 1024, 32, 0) },
+
+ { "m25pe20", INFO(0x208012, 0, 64 * 1024, 4, 0) },
+ { "m25pe80", INFO(0x208014, 0, 64 * 1024, 16, 0) },
+ { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) },
+
+ { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K) },
+ { "m25px32", INFO(0x207116, 0, 64 * 1024, 64, SECT_4K) },
+ { "m25px32-s0", INFO(0x207316, 0, 64 * 1024, 64, SECT_4K) },
+ { "m25px32-s1", INFO(0x206316, 0, 64 * 1024, 64, SECT_4K) },
+ { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) },
+ { "m25px80", INFO(0x207114, 0, 64 * 1024, 16, 0) },
+
+ /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
+ { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) },
+ { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) },
+ { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) },
+ { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) },
+ { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) },
+ { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) },
+ { "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64, SECT_4K) },
+ { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
+ { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
+ { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
+ { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) },
+ { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K) },
+
+ /* Catalyst / On Semiconductor -- non-JEDEC */
+ { "cat25c11", CAT25_INFO( 16, 8, 16, 1, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
+ { "cat25c03", CAT25_INFO( 32, 8, 16, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
+ { "cat25c09", CAT25_INFO( 128, 8, 32, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
+ { "cat25c17", CAT25_INFO( 256, 8, 32, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
+ { "cat25128", CAT25_INFO(2048, 8, 64, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
+ { },
+};
+
+static const struct spi_device_id *spi_nor_read_id(struct spi_nor *nor)
+{
+ int tmp;
+ u8 id[SPI_NOR_MAX_ID_LEN];
+ struct flash_info *info;
+
+ tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
+ if (tmp < 0) {
+ dev_dbg(nor->dev, " error %d reading JEDEC ID\n", tmp);
+ return ERR_PTR(tmp);
+ }
+
+ for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) {
+ info = (void *)spi_nor_ids[tmp].driver_data;
+ if (info->id_len) {
+ if (!memcmp(info->id, id, info->id_len))
+ return &spi_nor_ids[tmp];
+ }
+ }
+ dev_err(nor->dev, "unrecognized JEDEC id bytes: %02x, %2x, %2x\n",
+ id[0], id[1], id[2]);
+ return ERR_PTR(-ENODEV);
+}
+
+static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ int ret;
+
+ dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);
+
+ ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_READ);
+ if (ret)
+ return ret;
+
+ ret = nor->read(nor, from, len, retlen, buf);
+
+ spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_READ);
+ return ret;
+}
+
+static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ size_t actual;
+ int ret;
+
+ dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+
+ ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_WRITE);
+ if (ret)
+ return ret;
+
+ write_enable(nor);
+
+ nor->sst_write_second = false;
+
+ actual = to % 2;
+ /* Start write from odd address. */
+ if (actual) {
+ nor->program_opcode = SPINOR_OP_BP;
+
+ /* write one byte. */
+ nor->write(nor, to, 1, retlen, buf);
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto time_out;
+ }
+ to += actual;
+
+ /* Write out most of the data here. */
+ for (; actual < len - 1; actual += 2) {
+ nor->program_opcode = SPINOR_OP_AAI_WP;
+
+ /* write two bytes. */
+ nor->write(nor, to, 2, retlen, buf + actual);
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto time_out;
+ to += 2;
+ nor->sst_write_second = true;
+ }
+ nor->sst_write_second = false;
+
+ write_disable(nor);
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto time_out;
+
+ /* Write out trailing byte if it exists. */
+ if (actual != len) {
+ write_enable(nor);
+
+ nor->program_opcode = SPINOR_OP_BP;
+ nor->write(nor, to, 1, retlen, buf + actual);
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto time_out;
+ write_disable(nor);
+ }
+time_out:
+ spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_WRITE);
+ return ret;
+}
+
+/*
+ * Write an address range to the nor chip. Data must be written in
+ * FLASH_PAGESIZE chunks. The address range may be any size provided
+ * it is within the physical boundaries.
+ */
+static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ struct spi_nor *nor = mtd_to_spi_nor(mtd);
+ u32 page_offset, page_size, i;
+ int ret;
+
+ dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len);
+
+ ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_WRITE);
+ if (ret)
+ return ret;
+
+ write_enable(nor);
+
+ page_offset = to & (nor->page_size - 1);
+
+ /* do all the bytes fit onto one page? */
+ if (page_offset + len <= nor->page_size) {
+ nor->write(nor, to, len, retlen, buf);
+ } else {
+ /* the size of data remaining on the first page */
+ page_size = nor->page_size - page_offset;
+ nor->write(nor, to, page_size, retlen, buf);
+
+ /* write everything in nor->page_size chunks */
+ for (i = page_size; i < len; i += page_size) {
+ page_size = len - i;
+ if (page_size > nor->page_size)
+ page_size = nor->page_size;
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ goto write_err;
+
+ write_enable(nor);
+
+ nor->write(nor, to + i, page_size, retlen, buf + i);
+ }
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+write_err:
+ spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_WRITE);
+ return ret;
+}
+
+static int macronix_quad_enable(struct spi_nor *nor)
+{
+ int ret, val;
+
+ val = read_sr(nor);
+ write_enable(nor);
+
+ nor->cmd_buf[0] = val | SR_QUAD_EN_MX;
+ nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1, 0);
+
+ if (spi_nor_wait_till_ready(nor))
+ return 1;
+
+ ret = read_sr(nor);
+ if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) {
+ dev_err(nor->dev, "Macronix Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/*
+ * Write status Register and configuration register with 2 bytes
+ * The first byte will be written to the status register, while the
+ * second byte will be written to the configuration register.
+ * Return negative if error occured.
+ */
+static int write_sr_cr(struct spi_nor *nor, u16 val)
+{
+ nor->cmd_buf[0] = val & 0xff;
+ nor->cmd_buf[1] = (val >> 8);
+
+ return nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 2, 0);
+}
+
+static int spansion_quad_enable(struct spi_nor *nor)
+{
+ int ret;
+ int quad_en = CR_QUAD_EN_SPAN << 8;
+
+ write_enable(nor);
+
+ ret = write_sr_cr(nor, quad_en);
+ if (ret < 0) {
+ dev_err(nor->dev,
+ "error while writing configuration register\n");
+ return -EINVAL;
+ }
+
+ /* read back and check it */
+ ret = read_cr(nor);
+ if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
+ dev_err(nor->dev, "Spansion Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int set_quad_mode(struct spi_nor *nor, struct flash_info *info)
+{
+ int status;
+
+ switch (JEDEC_MFR(info)) {
+ case CFI_MFR_MACRONIX:
+ status = macronix_quad_enable(nor);
+ if (status) {
+ dev_err(nor->dev, "Macronix quad-read not enabled\n");
+ return -EINVAL;
+ }
+ return status;
+ default:
+ status = spansion_quad_enable(nor);
+ if (status) {
+ dev_err(nor->dev, "Spansion quad-read not enabled\n");
+ return -EINVAL;
+ }
+ return status;
+ }
+}
+
+static int spi_nor_check(struct spi_nor *nor)
+{
+ if (!nor->dev || !nor->read || !nor->write ||
+ !nor->read_reg || !nor->write_reg || !nor->erase) {
+ pr_err("spi-nor: please fill all the necessary fields!\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
+{
+ const struct spi_device_id *id = NULL;
+ struct flash_info *info;
+ struct device_d *dev = nor->dev;
+ struct mtd_info *mtd = nor->mtd;
+ struct device_node *np = dev->device_node;
+ int ret;
+ int i;
+
+ ret = spi_nor_check(nor);
+ if (ret)
+ return ret;
+
+ /* Try to auto-detect if chip name wasn't specified */
+ if (!name)
+ id = spi_nor_read_id(nor);
+ else
+ id = spi_nor_match_id(name);
+ if (IS_ERR_OR_NULL(id))
+ return -ENOENT;
+
+ info = (void *)id->driver_data;
+
+ /*
+ * If caller has specified name of flash model that can normally be
+ * detected using JEDEC, let's verify it.
+ */
+ if (name && info->id_len) {
+ const struct spi_device_id *jid;
+
+ jid = spi_nor_read_id(nor);
+ if (IS_ERR(jid)) {
+ return PTR_ERR(jid);
+ } else if (jid != id) {
+ /*
+ * JEDEC knows better, so overwrite platform ID. We
+ * can't trust partitions any longer, but we'll let
+ * mtd apply them anyway, since some partitions may be
+ * marked read-only, and we don't want to lose that
+ * information, even if it's not 100% accurate.
+ */
+ dev_warn(dev, "found %s, expected %s\n",
+ jid->name, id->name);
+ id = jid;
+ info = (void *)jid->driver_data;
+ }
+ }
+
+ mutex_init(&nor->lock);
+
+ /*
+ * Atmel, SST and Intel/Numonyx serial nor tend to power
+ * up with the software protection bits set
+ */
+
+ if (JEDEC_MFR(info) == CFI_MFR_ATMEL ||
+ JEDEC_MFR(info) == CFI_MFR_INTEL ||
+ JEDEC_MFR(info) == CFI_MFR_SST) {
+ write_enable(nor);
+ write_sr(nor, 0);
+ }
+
+ if (!mtd->name)
+ mtd->name = (char *) dev_name(dev);
+ mtd->type = MTD_NORFLASH;
+ mtd->writesize = 1;
+ mtd->flags = MTD_CAP_NORFLASH;
+ mtd->size = info->sector_size * info->n_sectors;
+ mtd->erase = spi_nor_erase;
+ mtd->read = spi_nor_read;
+
+ /* nor protection support for STmicro chips */
+ if (JEDEC_MFR(info) == CFI_MFR_ST) {
+ mtd->lock = spi_nor_lock;
+ mtd->unlock = spi_nor_unlock;
+ }
+
+ /* sst nor chips use AAI word program */
+ if (info->flags & SST_WRITE)
+ mtd->write = sst_write;
+ else
+ mtd->write = spi_nor_write;
+
+ if (info->flags & USE_FSR)
+ nor->flags |= SNOR_F_USE_FSR;
+
+#ifdef CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
+ /* prefer "small sector" erase if possible */
+ if (info->flags & SECT_4K) {
+ nor->erase_opcode = SPINOR_OP_BE_4K;
+ mtd->erasesize = 4096;
+ } else if (info->flags & SECT_4K_PMC) {
+ nor->erase_opcode = SPINOR_OP_BE_4K_PMC;
+ mtd->erasesize = 4096;
+ } else
+#endif
+ {
+ nor->erase_opcode = SPINOR_OP_SE;
+ mtd->erasesize = info->sector_size;
+ }
+
+ if (info->flags & SPI_NOR_NO_ERASE)
+ mtd->flags |= MTD_NO_ERASE;
+
+ nor->page_size = info->page_size;
+ mtd->writebufsize = nor->page_size;
+
+ if (np) {
+ /* If we were instantiated by DT, use it */
+ if (of_property_read_bool(np, "m25p,fast-read"))
+ nor->flash_read = SPI_NOR_FAST;
+ else
+ nor->flash_read = SPI_NOR_NORMAL;
+ } else {
+ /* If we weren't instantiated by DT, default to fast-read */
+ nor->flash_read = SPI_NOR_FAST;
+ }
+
+ /* Some devices cannot do fast-read, no matter what DT tells us */
+ if (info->flags & SPI_NOR_NO_FR)
+ nor->flash_read = SPI_NOR_NORMAL;
+
+ /* Quad/Dual-read mode takes precedence over fast/normal */
+ if (mode == SPI_NOR_QUAD && info->flags & SPI_NOR_QUAD_READ) {
+ ret = set_quad_mode(nor, info);
+ if (ret) {
+ dev_err(dev, "quad mode not supported\n");
+ return ret;
+ }
+ nor->flash_read = SPI_NOR_QUAD;
+ } else if (mode == SPI_NOR_DUAL && info->flags & SPI_NOR_DUAL_READ) {
+ nor->flash_read = SPI_NOR_DUAL;
+ }
+
+ /* Default commands */
+ switch (nor->flash_read) {
+ case SPI_NOR_QUAD:
+ nor->read_opcode = SPINOR_OP_READ_1_1_4;
+ break;
+ case SPI_NOR_DUAL:
+ nor->read_opcode = SPINOR_OP_READ_1_1_2;
+ break;
+ case SPI_NOR_FAST:
+ nor->read_opcode = SPINOR_OP_READ_FAST;
+ break;
+ case SPI_NOR_NORMAL:
+ nor->read_opcode = SPINOR_OP_READ;
+ break;
+ default:
+ dev_err(dev, "No Read opcode defined\n");
+ return -EINVAL;
+ }
+
+ nor->program_opcode = SPINOR_OP_PP;
+
+ if (info->addr_width)
+ nor->addr_width = info->addr_width;
+ else if (mtd->size > 0x1000000) {
+ /* enable 4-byte addressing if the device exceeds 16MiB */
+ nor->addr_width = 4;
+ if (JEDEC_MFR(info) == CFI_MFR_AMD) {
+ /* Dedicated 4-byte command set */
+ switch (nor->flash_read) {
+ case SPI_NOR_QUAD:
+ nor->read_opcode = SPINOR_OP_READ4_1_1_4;
+ break;
+ case SPI_NOR_DUAL:
+ nor->read_opcode = SPINOR_OP_READ4_1_1_2;
+ break;
+ case SPI_NOR_FAST:
+ nor->read_opcode = SPINOR_OP_READ4_FAST;
+ break;
+ case SPI_NOR_NORMAL:
+ nor->read_opcode = SPINOR_OP_READ4;
+ break;
+ }
+ nor->program_opcode = SPINOR_OP_PP_4B;
+ /* No small sector erase for 4-byte command set */
+ nor->erase_opcode = SPINOR_OP_SE_4B;
+ mtd->erasesize = info->sector_size;
+ } else
+ set_4byte(nor, info, 1);
+ } else {
+ nor->addr_width = 3;
+ }
+
+ nor->read_dummy = spi_nor_read_dummy_cycles(nor);
+
+ dev_info(dev, "%s (%lld Kbytes)\n", id->name,
+ (long long)mtd->size >> 10);
+
+ dev_dbg(dev,
+ "mtd .name = %s, .size = 0x%llx (%lldMiB), "
+ ".erasesize = 0x%.8x (%uKiB) .numeraseregions = %d\n",
+ mtd->name, (long long)mtd->size, (long long)(mtd->size >> 20),
+ mtd->erasesize, mtd->erasesize / 1024, mtd->numeraseregions);
+
+ if (mtd->numeraseregions)
+ for (i = 0; i < mtd->numeraseregions; i++)
+ dev_dbg(dev,
+ "mtd.eraseregions[%d] = { .offset = 0x%llx, "
+ ".erasesize = 0x%.8x (%uKiB), "
+ ".numblocks = %d }\n",
+ i, (long long)mtd->eraseregions[i].offset,
+ mtd->eraseregions[i].erasesize,
+ mtd->eraseregions[i].erasesize / 1024,
+ mtd->eraseregions[i].numblocks);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_nor_scan);
+
+static const struct spi_device_id *spi_nor_match_id(const char *name)
+{
+ const struct spi_device_id *id = spi_nor_ids;
+
+ while (id->name[0]) {
+ if (!strcmp(name, id->name))
+ return id;
+ id++;
+ }
+ return NULL;
+}
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index c8220756884d..d8125214a04a 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -17,4 +17,11 @@ struct pci_device_id {
__u32 class, class_mask; /* (class,subclass,prog-if) triplet */
};
+#define SPI_NAME_SIZE 32
+
+struct spi_device_id {
+ char name[SPI_NAME_SIZE];
+ unsigned long driver_data;
+};
+
#endif /* LINUX_MOD_DEVICETABLE_H */
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
new file mode 100644
index 000000000000..f099406c534a
--- /dev/null
+++ b/include/linux/mtd/spi-nor.h
@@ -0,0 +1,204 @@
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __LINUX_MTD_SPI_NOR_H
+#define __LINUX_MTD_SPI_NOR_H
+
+/*
+ * Note on opcode nomenclature: some opcodes have a format like
+ * SPINOR_OP_FUNCTION{4,}_x_y_z. The numbers x, y, and z stand for the number
+ * of I/O lines used for the opcode, address, and data (respectively). The
+ * FUNCTION has an optional suffix of '4', to represent an opcode which
+ * requires a 4-byte (32-bit) address.
+ */
+
+/* Flash opcodes. */
+#define SPINOR_OP_WREN 0x06 /* Write enable */
+#define SPINOR_OP_RDSR 0x05 /* Read status register */
+#define SPINOR_OP_WRSR 0x01 /* Write status register 1 byte */
+#define SPINOR_OP_READ 0x03 /* Read data bytes (low frequency) */
+#define SPINOR_OP_READ_FAST 0x0b /* Read data bytes (high frequency) */
+#define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual SPI) */
+#define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad SPI) */
+#define SPINOR_OP_PP 0x02 /* Page program (up to 256 bytes) */
+#define SPINOR_OP_BE_4K 0x20 /* Erase 4KiB block */
+#define SPINOR_OP_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */
+#define SPINOR_OP_BE_32K 0x52 /* Erase 32KiB block */
+#define SPINOR_OP_CHIP_ERASE 0xc7 /* Erase whole flash chip */
+#define SPINOR_OP_SE 0xd8 /* Sector erase (usually 64KiB) */
+#define SPINOR_OP_RDID 0x9f /* Read JEDEC ID */
+#define SPINOR_OP_RDCR 0x35 /* Read configuration register */
+#define SPINOR_OP_RDFSR 0x70 /* Read flag status register */
+
+/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
+#define SPINOR_OP_READ4 0x13 /* Read data bytes (low frequency) */
+#define SPINOR_OP_READ4_FAST 0x0c /* Read data bytes (high frequency) */
+#define SPINOR_OP_READ4_1_1_2 0x3c /* Read data bytes (Dual SPI) */
+#define SPINOR_OP_READ4_1_1_4 0x6c /* Read data bytes (Quad SPI) */
+#define SPINOR_OP_PP_4B 0x12 /* Page program (up to 256 bytes) */
+#define SPINOR_OP_SE_4B 0xdc /* Sector erase (usually 64KiB) */
+
+/* Used for SST flashes only. */
+#define SPINOR_OP_BP 0x02 /* Byte program */
+#define SPINOR_OP_WRDI 0x04 /* Write disable */
+#define SPINOR_OP_AAI_WP 0xad /* Auto address increment word program */
+
+/* Used for Macronix and Winbond flashes. */
+#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */
+#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */
+
+/* Used for Spansion flashes only. */
+#define SPINOR_OP_BRWR 0x17 /* Bank register write */
+
+/* Status Register bits. */
+#define SR_WIP 1 /* Write in progress */
+#define SR_WEL 2 /* Write enable latch */
+/* meaning of other SR_* bits may differ between vendors */
+#define SR_BP0 4 /* Block protect 0 */
+#define SR_BP1 8 /* Block protect 1 */
+#define SR_BP2 0x10 /* Block protect 2 */
+#define SR_SRWD 0x80 /* SR write protect */
+
+#define SR_QUAD_EN_MX 0x40 /* Macronix Quad I/O */
+
+/* Flag Status Register bits */
+#define FSR_READY 0x80
+
+/* Configuration Register bits. */
+#define CR_QUAD_EN_SPAN 0x2 /* Spansion Quad I/O */
+
+enum read_mode {
+ SPI_NOR_NORMAL = 0,
+ SPI_NOR_FAST,
+ SPI_NOR_DUAL,
+ SPI_NOR_QUAD,
+};
+
+/**
+ * struct spi_nor_xfer_cfg - Structure for defining a Serial Flash transfer
+ * @wren: command for "Write Enable", or 0x00 for not required
+ * @cmd: command for operation
+ * @cmd_pins: number of pins to send @cmd (1, 2, 4)
+ * @addr: address for operation
+ * @addr_pins: number of pins to send @addr (1, 2, 4)
+ * @addr_width: number of address bytes
+ * (3,4, or 0 for address not required)
+ * @mode: mode data
+ * @mode_pins: number of pins to send @mode (1, 2, 4)
+ * @mode_cycles: number of mode cycles (0 for mode not required)
+ * @dummy_cycles: number of dummy cycles (0 for dummy not required)
+ */
+struct spi_nor_xfer_cfg {
+ u8 wren;
+ u8 cmd;
+ u8 cmd_pins;
+ u32 addr;
+ u8 addr_pins;
+ u8 addr_width;
+ u8 mode;
+ u8 mode_pins;
+ u8 mode_cycles;
+ u8 dummy_cycles;
+};
+
+#define SPI_NOR_MAX_CMD_SIZE 8
+enum spi_nor_ops {
+ SPI_NOR_OPS_READ = 0,
+ SPI_NOR_OPS_WRITE,
+ SPI_NOR_OPS_ERASE,
+ SPI_NOR_OPS_LOCK,
+ SPI_NOR_OPS_UNLOCK,
+};
+
+enum spi_nor_option_flags {
+ SNOR_F_USE_FSR = BIT(0),
+};
+
+/**
+ * struct spi_nor - Structure for defining a the SPI NOR layer
+ * @mtd: point to a mtd_info structure
+ * @lock: the lock for the read/write/erase/lock/unlock operations
+ * @dev: point to a spi device, or a spi nor controller device.
+ * @page_size: the page size of the SPI NOR
+ * @addr_width: number of address bytes
+ * @erase_opcode: the opcode for erasing a sector
+ * @read_opcode: the read opcode
+ * @read_dummy: the dummy needed by the read operation
+ * @program_opcode: the program opcode
+ * @flash_read: the mode of the read
+ * @sst_write_second: used by the SST write operation
+ * @flags: flag options for the current SPI-NOR (SNOR_F_*)
+ * @cfg: used by the read_xfer/write_xfer
+ * @cmd_buf: used by the write_reg
+ * @prepare: [OPTIONAL] do some preparations for the
+ * read/write/erase/lock/unlock operations
+ * @unprepare: [OPTIONAL] do some post work after the
+ * read/write/erase/lock/unlock operations
+ * @read_xfer: [OPTIONAL] the read fundamental primitive
+ * @write_xfer: [OPTIONAL] the writefundamental primitive
+ * @read_reg: [DRIVER-SPECIFIC] read out the register
+ * @write_reg: [DRIVER-SPECIFIC] write data to the register
+ * @read: [DRIVER-SPECIFIC] read data from the SPI NOR
+ * @write: [DRIVER-SPECIFIC] write data to the SPI NOR
+ * @erase: [DRIVER-SPECIFIC] erase a sector of the SPI NOR
+ * at the offset @offs
+ * @priv: the private data
+ */
+struct spi_nor {
+ struct mtd_info *mtd;
+ struct mutex lock;
+ struct device_d *dev;
+ u32 page_size;
+ u8 addr_width;
+ u8 erase_opcode;
+ u8 read_opcode;
+ u8 read_dummy;
+ u8 program_opcode;
+ enum read_mode flash_read;
+ bool sst_write_second;
+ u32 flags;
+ struct spi_nor_xfer_cfg cfg;
+ u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE];
+
+ int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops);
+ void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops);
+ int (*read_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg,
+ u8 *buf, size_t len);
+ int (*write_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg,
+ u8 *buf, size_t len);
+ int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len);
+ int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len,
+ int write_enable);
+
+ int (*read)(struct spi_nor *nor, loff_t from,
+ size_t len, size_t *retlen, u_char *read_buf);
+ void (*write)(struct spi_nor *nor, loff_t to,
+ size_t len, size_t *retlen, const u_char *write_buf);
+ int (*erase)(struct spi_nor *nor, loff_t offs);
+
+ void *priv;
+};
+
+/**
+ * spi_nor_scan() - scan the SPI NOR
+ * @nor: the spi_nor structure
+ * @name: the chip type name
+ * @mode: the read mode supported by the driver
+ *
+ * The drivers can use this fuction to scan the SPI NOR.
+ * In the scanning, it will try to get all the necessary information to
+ * fill the mtd_info{} and the spi_nor{}.
+ *
+ * The chip type name can be provided through the @name parameter.
+ *
+ * Return: 0 for success, others for failure.
+ */
+int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode);
+
+#endif
--
2.1.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH v2 2/8] mtd: spi-nor: add cadence quadspi driver
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 1/8] mtd: spi-nor: add SPI-NOR framework Steffen Trumtrar
@ 2015-05-28 15:56 ` Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 3/8] ARM: dts: socfpga: add qspi node Steffen Trumtrar
` (6 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-28 15:56 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
drivers/mtd/spi-nor/Kconfig | 9 +
drivers/mtd/spi-nor/Makefile | 1 +
drivers/mtd/spi-nor/cadence-quadspi.c | 1211 +++++++++++++++++++++++++++++++++
include/platform_data/cadence_qspi.h | 9 +
4 files changed, 1230 insertions(+)
create mode 100644 drivers/mtd/spi-nor/cadence-quadspi.c
create mode 100644 include/platform_data/cadence_qspi.h
diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
index 1568b2fb6d69..a84591fdd139 100644
--- a/drivers/mtd/spi-nor/Kconfig
+++ b/drivers/mtd/spi-nor/Kconfig
@@ -4,3 +4,12 @@ menuconfig MTD_SPI_NOR
help
This is the framework for the SPI NOR which can be used by the SPI
device drivers and the SPI-NOR device driver.
+
+if MTD_SPI_NOR
+
+config SPI_CADENCE_QUADSPI
+ tristate "Cadence Quad SPI controller"
+ help
+ This enables support for the Cadence Quad SPI controller and NOR flash.
+
+endif
diff --git a/drivers/mtd/spi-nor/Makefile b/drivers/mtd/spi-nor/Makefile
index fe88e3d86ee5..4e00f38a7d86 100644
--- a/drivers/mtd/spi-nor/Makefile
+++ b/drivers/mtd/spi-nor/Makefile
@@ -1 +1,2 @@
obj-$(CONFIG_MTD_SPI_NOR) += spi-nor.o
+obj-$(CONFIG_SPI_CADENCE_QUADSPI) += cadence-quadspi.o
diff --git a/drivers/mtd/spi-nor/cadence-quadspi.c b/drivers/mtd/spi-nor/cadence-quadspi.c
new file mode 100644
index 000000000000..dce29ca0ea02
--- /dev/null
+++ b/drivers/mtd/spi-nor/cadence-quadspi.c
@@ -0,0 +1,1211 @@
+/*
+ * Copyright (C) 2015 Pengutronix, Steffen Trumtrar <s.trumtrar@pengutronix.de>
+ *
+ * derived from Linux kernel driver by
+ *
+ * Driver for Cadence QSPI Controller
+ *
+ * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <clock.h>
+#include <common.h>
+#include <driver.h>
+#include <errno.h>
+#include <init.h>
+#include <io.h>
+#include <linux/clk.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/spi-nor.h>
+#include <of.h>
+#include <platform_data/cadence_qspi.h>
+#include <spi/spi.h>
+
+#define CQSPI_MAX_CHIPSELECT 16
+
+struct cqspi_flash_pdata {
+ struct mtd_info mtd;
+ struct spi_nor nor;
+ u32 clk_rate;
+ unsigned int block_size;
+ unsigned int read_delay;
+ unsigned int tshsl_ns;
+ unsigned int tsd2d_ns;
+ unsigned int tchsh_ns;
+ unsigned int tslch_ns;
+};
+
+struct cqspi_st {
+ struct device_d *dev;
+ struct clk *l4_mp_clk;
+ struct clk *qspi_clk;
+ unsigned int sclk;
+
+ void __iomem *iobase;
+ void __iomem *ahb_base;
+ unsigned int irq_mask;
+ int current_cs;
+ unsigned int master_ref_clk_hz;
+ unsigned int ext_decoder;
+ unsigned int fifo_depth;
+ struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIPSELECT];
+ bool no_reconfig;
+};
+
+/* Operation timeout value */
+#define CQSPI_TIMEOUT_MS 800 * MSECOND
+#define CQSPI_READ_TIMEOUT_MS 100 * MSECOND
+#define CQSPI_POLL_IDLE_RETRY 3
+
+#define CQSPI_FIFO_WIDTH 4
+
+#define CQSPI_REG_SRAM_THRESHOLD_BYTES 50
+
+/* Instruction type */
+#define CQSPI_INST_TYPE_SINGLE 0
+#define CQSPI_INST_TYPE_DUAL 1
+#define CQSPI_INST_TYPE_QUAD 2
+
+#define CQSPI_DUMMY_CLKS_PER_BYTE 8
+#define CQSPI_DUMMY_BYTES_MAX 4
+
+#define CQSPI_STIG_DATA_LEN_MAX 8
+
+#define CQSPI_INDIRECTTRIGGER_ADDR_MASK 0xFFFFF
+
+/* Register map */
+#define CQSPI_REG_CONFIG 0x00
+#define CQSPI_REG_CONFIG_ENABLE_MASK BIT(0)
+#define CQSPI_REG_CONFIG_DECODE_MASK BIT(9)
+#define CQSPI_REG_CONFIG_CHIPSELECT_LSB 10
+#define CQSPI_REG_CONFIG_DMA_MASK BIT(15)
+#define CQSPI_REG_CONFIG_BAUD_LSB 19
+#define CQSPI_REG_CONFIG_IDLE_LSB 31
+#define CQSPI_REG_CONFIG_CHIPSELECT_MASK 0xF
+#define CQSPI_REG_CONFIG_BAUD_MASK 0xF
+
+#define CQSPI_REG_RD_INSTR 0x04
+#define CQSPI_REG_RD_INSTR_OPCODE_LSB 0
+#define CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB 8
+#define CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB 12
+#define CQSPI_REG_RD_INSTR_TYPE_DATA_LSB 16
+#define CQSPI_REG_RD_INSTR_MODE_EN_LSB 20
+#define CQSPI_REG_RD_INSTR_DUMMY_LSB 24
+#define CQSPI_REG_RD_INSTR_TYPE_INSTR_MASK 0x3
+#define CQSPI_REG_RD_INSTR_TYPE_ADDR_MASK 0x3
+#define CQSPI_REG_RD_INSTR_TYPE_DATA_MASK 0x3
+#define CQSPI_REG_RD_INSTR_DUMMY_MASK 0x1F
+
+#define CQSPI_REG_WR_INSTR 0x08
+#define CQSPI_REG_WR_INSTR_OPCODE_LSB 0
+#define CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB 12
+#define CQSPI_REG_WR_INSTR_TYPE_DATA_LSB 16
+
+#define CQSPI_REG_DELAY 0x0C
+#define CQSPI_REG_DELAY_TSLCH_LSB 0
+#define CQSPI_REG_DELAY_TCHSH_LSB 8
+#define CQSPI_REG_DELAY_TSD2D_LSB 16
+#define CQSPI_REG_DELAY_TSHSL_LSB 24
+#define CQSPI_REG_DELAY_TSLCH_MASK 0xFF
+#define CQSPI_REG_DELAY_TCHSH_MASK 0xFF
+#define CQSPI_REG_DELAY_TSD2D_MASK 0xFF
+#define CQSPI_REG_DELAY_TSHSL_MASK 0xFF
+
+#define CQSPI_REG_READCAPTURE 0x10
+#define CQSPI_REG_READCAPTURE_BYPASS_LSB 0
+#define CQSPI_REG_READCAPTURE_DELAY_LSB 1
+#define CQSPI_REG_READCAPTURE_DELAY_MASK 0xF
+
+#define CQSPI_REG_SIZE 0x14
+#define CQSPI_REG_SIZE_ADDRESS_LSB 0
+#define CQSPI_REG_SIZE_PAGE_LSB 4
+#define CQSPI_REG_SIZE_BLOCK_LSB 16
+#define CQSPI_REG_SIZE_ADDRESS_MASK 0xF
+#define CQSPI_REG_SIZE_PAGE_MASK 0xFFF
+#define CQSPI_REG_SIZE_BLOCK_MASK 0x3F
+
+#define CQSPI_REG_SRAMPARTITION 0x18
+#define CQSPI_REG_INDIRECTTRIGGER 0x1C
+
+#define CQSPI_REG_DMA 0x20
+#define CQSPI_REG_DMA_SINGLE_LSB 0
+#define CQSPI_REG_DMA_BURST_LSB 8
+#define CQSPI_REG_DMA_SINGLE_MASK 0xFF
+#define CQSPI_REG_DMA_BURST_MASK 0xFF
+
+#define CQSPI_REG_REMAP 0x24
+#define CQSPI_REG_MODE_BIT 0x28
+
+#define CQSPI_REG_SRAMLEVEL 0x2C
+#define CQSPI_REG_SRAMLEVEL_RD_LSB 0
+#define CQSPI_REG_SRAMLEVEL_WR_LSB 16
+#define CQSPI_REG_SRAMLEVEL_RD_MASK 0xFFFF
+#define CQSPI_REG_SRAMLEVEL_WR_MASK 0xFFFF
+
+#define CQSPI_REG_IRQSTATUS 0x40
+#define CQSPI_REG_IRQMASK 0x44
+
+#define CQSPI_REG_INDIRECTRD 0x60
+#define CQSPI_REG_INDIRECTRD_START_MASK BIT(0)
+#define CQSPI_REG_INDIRECTRD_CANCEL_MASK BIT(1)
+#define CQSPI_REG_INDIRECTRD_DONE_MASK BIT(5)
+
+#define CQSPI_REG_INDIRECTRDWATERMARK 0x64
+#define CQSPI_REG_INDIRECTRDSTARTADDR 0x68
+#define CQSPI_REG_INDIRECTRDBYTES 0x6C
+
+#define CQSPI_REG_CMDCTRL 0x90
+#define CQSPI_REG_CMDCTRL_EXECUTE_MASK BIT(0)
+#define CQSPI_REG_CMDCTRL_INPROGRESS_MASK BIT(1)
+#define CQSPI_REG_CMDCTRL_WR_BYTES_LSB 12
+#define CQSPI_REG_CMDCTRL_WR_EN_LSB 15
+#define CQSPI_REG_CMDCTRL_ADD_BYTES_LSB 16
+#define CQSPI_REG_CMDCTRL_ADDR_EN_LSB 19
+#define CQSPI_REG_CMDCTRL_RD_BYTES_LSB 20
+#define CQSPI_REG_CMDCTRL_RD_EN_LSB 23
+#define CQSPI_REG_CMDCTRL_OPCODE_LSB 24
+#define CQSPI_REG_CMDCTRL_WR_BYTES_MASK 0x7
+#define CQSPI_REG_CMDCTRL_ADD_BYTES_MASK 0x3
+#define CQSPI_REG_CMDCTRL_RD_BYTES_MASK 0x7
+
+#define CQSPI_REG_INDIRECTWR 0x70
+#define CQSPI_REG_INDIRECTWR_START_MASK BIT(0)
+#define CQSPI_REG_INDIRECTWR_CANCEL_MASK BIT(1)
+#define CQSPI_REG_INDIRECTWR_DONE_MASK BIT(5)
+
+#define CQSPI_REG_INDIRECTWRWATERMARK 0x74
+#define CQSPI_REG_INDIRECTWRSTARTADDR 0x78
+#define CQSPI_REG_INDIRECTWRBYTES 0x7C
+
+#define CQSPI_REG_CMDADDRESS 0x94
+#define CQSPI_REG_CMDREADDATALOWER 0xA0
+#define CQSPI_REG_CMDREADDATAUPPER 0xA4
+#define CQSPI_REG_CMDWRITEDATALOWER 0xA8
+#define CQSPI_REG_CMDWRITEDATAUPPER 0xAC
+
+/* Interrupt status bits */
+#define CQSPI_REG_IRQ_MODE_ERR BIT(0)
+#define CQSPI_REG_IRQ_UNDERFLOW BIT(1)
+#define CQSPI_REG_IRQ_IND_COMP BIT(2)
+#define CQSPI_REG_IRQ_IND_RD_REJECT BIT(3)
+#define CQSPI_REG_IRQ_WR_PROTECTED_ERR BIT(4)
+#define CQSPI_REG_IRQ_ILLEGAL_AHB_ERR BIT(5)
+#define CQSPI_REG_IRQ_WATERMARK BIT(6)
+#define CQSPI_REG_IRQ_IND_RD_OVERFLOW BIT(12)
+
+#define CQSPI_IRQ_STATUS_ERR (CQSPI_REG_IRQ_MODE_ERR | \
+ CQSPI_REG_IRQ_IND_RD_REJECT | \
+ CQSPI_REG_IRQ_WR_PROTECTED_ERR | \
+ CQSPI_REG_IRQ_ILLEGAL_AHB_ERR)
+
+#define CQSPI_IRQ_MASK_RD (CQSPI_REG_IRQ_WATERMARK | \
+ CQSPI_REG_IRQ_IND_RD_OVERFLOW | \
+ CQSPI_REG_IRQ_IND_COMP)
+
+#define CQSPI_IRQ_MASK_WR (CQSPI_REG_IRQ_IND_COMP | \
+ CQSPI_REG_IRQ_WATERMARK | \
+ CQSPI_REG_IRQ_UNDERFLOW)
+
+#define CQSPI_IRQ_STATUS_MASK 0x1FFFE
+
+#define CQSPI_REG_IS_IDLE(base) \
+ ((readl(base + CQSPI_REG_CONFIG) >> \
+ CQSPI_REG_CONFIG_IDLE_LSB) & 0x1)
+
+#define CQSPI_GET_RD_SRAM_LEVEL(reg_base) \
+ (((readl(reg_base + CQSPI_REG_SRAMLEVEL)) >> \
+ CQSPI_REG_SRAMLEVEL_RD_LSB) & CQSPI_REG_SRAMLEVEL_RD_MASK)
+
+static void cqspi_fifo_read(void *dest, const void *src_ahb_addr,
+ unsigned int bytes)
+{
+ unsigned int temp;
+ int remaining = bytes;
+ unsigned int *dest_ptr = (unsigned int *)dest;
+ unsigned int *src_ptr = (unsigned int *)src_ahb_addr;
+
+ while (remaining > CQSPI_FIFO_WIDTH) {
+ *dest_ptr = readl(src_ptr);
+ dest_ptr++;
+ remaining -= CQSPI_FIFO_WIDTH;
+ }
+ if (remaining > 0) {
+ /* dangling bytes */
+ temp = readl(src_ptr);
+ memcpy(dest_ptr, &temp, remaining);
+ }
+}
+
+static void cqspi_fifo_write(void *dest_ahb_addr,
+ const void *src, unsigned int bytes)
+{
+ unsigned int temp;
+ int remaining = bytes;
+ unsigned int *dest_ptr = (unsigned int *)dest_ahb_addr;
+ unsigned int *src_ptr = (unsigned int *)src;
+
+ while (remaining > CQSPI_FIFO_WIDTH) {
+ writel(*src_ptr, dest_ptr);
+ src_ptr++;
+ remaining -= CQSPI_FIFO_WIDTH;
+ }
+ if (remaining > 0) {
+ /* dangling bytes */
+ memcpy(&temp, src_ptr, remaining);
+ writel(temp, dest_ptr);
+ }
+}
+
+static int cqspi_find_chipselect(struct spi_nor *nor)
+{
+ int cs = -1;
+ struct cqspi_st *cqspi = nor->priv;
+
+ for (cs = 0; cs < CQSPI_MAX_CHIPSELECT; cs++)
+ if (nor == &cqspi->f_pdata[cs].nor)
+ break;
+ return cs;
+}
+
+static unsigned int cqspi_calc_rdreg(struct spi_nor *nor, u8 opcode)
+{
+ unsigned int rdreg = 0;
+ struct cqspi_st *cqspi = nor->priv;
+ struct cqspi_flash_pdata *f_pdata;
+
+ f_pdata = &cqspi->f_pdata[cqspi->current_cs];
+
+ if (nor->flash_read == SPI_NOR_QUAD)
+ rdreg |= (CQSPI_INST_TYPE_QUAD
+ << CQSPI_REG_RD_INSTR_TYPE_DATA_LSB);
+ return rdreg;
+}
+
+static unsigned int cqspi_wait_idle(struct cqspi_st *cqspi)
+{
+ void __iomem *reg_base = cqspi->iobase;
+
+ if (wait_on_timeout(CQSPI_TIMEOUT_MS,
+ CQSPI_REG_IS_IDLE(reg_base))) {
+ /* Timeout, in busy mode. */
+ dev_err(cqspi->dev, "QSPI is still busy after %llums timeout.\n",
+ CQSPI_TIMEOUT_MS);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int cqspi_exec_flash_cmd(struct cqspi_st *cqspi, unsigned int reg)
+{
+ void __iomem *reg_base = cqspi->iobase;
+
+ /* Write the CMDCTRL without start execution. */
+ writel(reg, reg_base + CQSPI_REG_CMDCTRL);
+ /* Start execute */
+ reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK;
+ writel(reg, reg_base + CQSPI_REG_CMDCTRL);
+
+ if (wait_on_timeout(CQSPI_TIMEOUT_MS,
+ (readl(reg_base + CQSPI_REG_CMDCTRL) &
+ CQSPI_REG_CMDCTRL_INPROGRESS_MASK) == 0)) {
+ dev_err(cqspi->dev, "flash cmd execute time out (0x%08x)\n",
+ readl(reg_base + CQSPI_REG_CMDCTRL));
+ return -EIO;
+ }
+
+ /* Polling QSPI idle status. */
+ return cqspi_wait_idle(cqspi);
+}
+
+static int cqspi_command_read(struct spi_nor *nor,
+ const u8 *txbuf, unsigned n_tx,
+ u8 *rxbuf, unsigned n_rx)
+{
+ unsigned int reg;
+ unsigned int read_len;
+ int status;
+ struct cqspi_st *cqspi = nor->priv;
+ void __iomem *reg_base = cqspi->iobase;
+ unsigned int rdreg;
+
+ if (!n_rx || n_rx > CQSPI_STIG_DATA_LEN_MAX || rxbuf == NULL) {
+ dev_err(nor->dev,
+ "Invalid input argument, len %d rxbuf 0x%08x\n", n_rx,
+ (unsigned int)rxbuf);
+ return -EINVAL;
+ }
+
+ reg = txbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
+
+ rdreg = cqspi_calc_rdreg(nor, txbuf[0]);
+ writel(rdreg, reg_base + CQSPI_REG_RD_INSTR);
+
+ reg |= (0x1 << CQSPI_REG_CMDCTRL_RD_EN_LSB);
+
+ /* 0 means 1 byte. */
+ reg |= (((n_rx - 1) & CQSPI_REG_CMDCTRL_RD_BYTES_MASK)
+ << CQSPI_REG_CMDCTRL_RD_BYTES_LSB);
+ status = cqspi_exec_flash_cmd(cqspi, reg);
+ if (status != 0)
+ return status;
+
+ reg = readl(reg_base + CQSPI_REG_CMDREADDATALOWER);
+
+ /* Put the read value into rx_buf */
+ read_len = (n_rx > 4) ? 4 : n_rx;
+ memcpy(rxbuf, ®, read_len);
+ rxbuf += read_len;
+
+ if (n_rx > 4) {
+ reg = readl(reg_base + CQSPI_REG_CMDREADDATAUPPER);
+
+ read_len = n_rx - read_len;
+ memcpy(rxbuf, ®, read_len);
+ }
+
+ return 0;
+}
+
+static __maybe_unused int cqspi_command_write(struct spi_nor *nor,
+ u8 opcode, const u8 *txbuf, unsigned n_tx)
+{
+ unsigned int reg;
+ unsigned int data;
+ struct cqspi_st *cqspi = nor->priv;
+ void __iomem *reg_base = cqspi->iobase;
+
+ if (n_tx > 4 || (n_tx && txbuf == NULL)) {
+ dev_err(nor->dev,
+ "Invalid input argument, cmdlen %d txbuf 0x%08x\n",
+ n_tx, (unsigned int)txbuf);
+ return -EINVAL;
+ }
+
+ reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;
+ if (n_tx) {
+ reg |= (0x1 << CQSPI_REG_CMDCTRL_WR_EN_LSB);
+ reg |= ((n_tx - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK)
+ << CQSPI_REG_CMDCTRL_WR_BYTES_LSB;
+ data = 0;
+ memcpy(&data, txbuf, n_tx);
+ writel(data, reg_base + CQSPI_REG_CMDWRITEDATALOWER);
+ }
+
+ return cqspi_exec_flash_cmd(cqspi, reg);
+}
+
+static int cqspi_command_write_addr(struct spi_nor *nor,
+ u8 opcode, unsigned int addr)
+{
+ unsigned int reg;
+ struct cqspi_st *cqspi = nor->priv;
+ void __iomem *reg_base = cqspi->iobase;
+
+ reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB;
+ reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
+ reg |= ((nor->addr_width - 1) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
+ << CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
+
+ writel(addr, reg_base + CQSPI_REG_CMDADDRESS);
+
+ return cqspi_exec_flash_cmd(cqspi, reg);
+}
+
+static int cqspi_indirect_read_setup(struct spi_nor *nor,
+ unsigned int from_addr)
+{
+ struct cqspi_st *cqspi = nor->priv;
+ unsigned int ahb_base = (unsigned int) cqspi->ahb_base;
+ void __iomem *reg_base = cqspi->iobase;
+ unsigned int dummy_clk = 0;
+ unsigned int dummy_bytes;
+ unsigned int reg = 0;
+
+ writel(ahb_base & CQSPI_INDIRECTTRIGGER_ADDR_MASK,
+ reg_base + CQSPI_REG_INDIRECTTRIGGER);
+ writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
+
+ reg = nor->read_opcode << CQSPI_REG_RD_INSTR_OPCODE_LSB;
+ reg |= cqspi_calc_rdreg(nor, nor->read_opcode);
+
+ /* Setup dummy clock cycles */
+ dummy_bytes = nor->read_dummy / 8;
+
+ if (dummy_bytes) {
+ struct cqspi_flash_pdata *f_pdata;
+
+ f_pdata = &cqspi->f_pdata[cqspi->current_cs];
+
+ if (dummy_bytes > CQSPI_DUMMY_BYTES_MAX)
+ dummy_bytes = CQSPI_DUMMY_BYTES_MAX;
+
+ reg |= (1 << CQSPI_REG_RD_INSTR_MODE_EN_LSB);
+ /* Set mode bits high to ensure chip doesn't enter XIP */
+ writel(0xFF, reg_base + CQSPI_REG_MODE_BIT);
+
+ /* Convert to clock cycles. */
+ dummy_clk = dummy_bytes * CQSPI_DUMMY_CLKS_PER_BYTE;
+ /* Need to subtract the mode byte (8 clocks). */
+ dummy_clk -= CQSPI_DUMMY_CLKS_PER_BYTE;
+
+ if (dummy_clk)
+ reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
+ << CQSPI_REG_RD_INSTR_DUMMY_LSB;
+ }
+
+ writel(reg, reg_base + CQSPI_REG_RD_INSTR);
+
+ /* Set address width */
+ reg = readl(reg_base + CQSPI_REG_SIZE);
+ reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
+ reg |= (nor->addr_width) - 1;
+ writel(reg, reg_base + CQSPI_REG_SIZE);
+ return 0;
+}
+
+static int cqspi_indirect_read_execute(struct spi_nor *nor,
+ u8 *rxbuf, unsigned n_rx)
+{
+ int ret = 0;
+ unsigned int reg = 0;
+ unsigned int bytes_to_read = 0;
+ unsigned int watermark;
+ struct cqspi_st *cqspi = nor->priv;
+ void __iomem *reg_base = cqspi->iobase;
+ void __iomem *ahb_base = cqspi->ahb_base;
+ int remaining = (int)n_rx;
+
+ watermark = cqspi->fifo_depth * CQSPI_FIFO_WIDTH / 2;
+ writel(watermark, reg_base + CQSPI_REG_INDIRECTRDWATERMARK);
+ writel(remaining, reg_base + CQSPI_REG_INDIRECTRDBYTES);
+
+ /* Clear all interrupts. */
+ writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
+
+ cqspi->irq_mask = CQSPI_IRQ_MASK_RD;
+ writel(cqspi->irq_mask, reg_base + CQSPI_REG_IRQMASK);
+
+ writel(CQSPI_REG_INDIRECTRD_START_MASK,
+ reg_base + CQSPI_REG_INDIRECTRD);
+
+ while (remaining > 0) {
+ unsigned int irq_status;
+
+ ret = wait_on_timeout(CQSPI_READ_TIMEOUT_MS,
+ readl(reg_base + CQSPI_REG_IRQSTATUS) & cqspi->irq_mask);
+
+ irq_status = readl(reg_base + CQSPI_REG_IRQSTATUS);
+ bytes_to_read = CQSPI_GET_RD_SRAM_LEVEL(reg_base);
+
+ /* Clear all interrupts. */
+ writel(irq_status, reg_base + CQSPI_REG_IRQSTATUS);
+
+ if (!ret && bytes_to_read == 0) {
+ dev_err(nor->dev, "Indirect read timeout, no bytes\n");
+ ret = -ETIMEDOUT;
+ goto failrd;
+ }
+
+ while (bytes_to_read != 0) {
+ bytes_to_read *= CQSPI_FIFO_WIDTH;
+ bytes_to_read = bytes_to_read > remaining
+ ? remaining : bytes_to_read;
+ cqspi_fifo_read(rxbuf, ahb_base, bytes_to_read);
+ rxbuf += bytes_to_read;
+ remaining -= bytes_to_read;
+ bytes_to_read = CQSPI_GET_RD_SRAM_LEVEL(reg_base);
+ }
+ }
+
+ /* Check indirect done status */
+ if (wait_on_timeout(CQSPI_TIMEOUT_MS,
+ readl(reg_base + CQSPI_REG_INDIRECTRD) &
+ CQSPI_REG_INDIRECTRD_DONE_MASK)) {
+ dev_err(nor->dev,
+ "Indirect read completion error 0x%08x\n", reg);
+ ret = -ETIMEDOUT;
+ goto failrd;
+ }
+
+ /* Disable interrupt */
+ writel(0, reg_base + CQSPI_REG_IRQMASK);
+
+ /* Clear indirect completion status */
+ writel(CQSPI_REG_INDIRECTRD_DONE_MASK, reg_base + CQSPI_REG_INDIRECTRD);
+
+ return 0;
+
+ failrd:
+ /* Disable interrupt */
+ writel(0, reg_base + CQSPI_REG_IRQMASK);
+
+ /* Cancel the indirect read */
+ writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
+ reg_base + CQSPI_REG_INDIRECTRD);
+ return ret;
+}
+
+static __maybe_unused int cqspi_indirect_write_setup(struct spi_nor *nor,
+ unsigned int to_addr)
+{
+ unsigned int reg;
+ struct cqspi_st *cqspi = nor->priv;
+ void __iomem *reg_base = cqspi->iobase;
+
+ /* Set opcode. */
+ reg = nor->program_opcode << CQSPI_REG_WR_INSTR_OPCODE_LSB;
+ writel(reg, reg_base + CQSPI_REG_WR_INSTR);
+ reg = cqspi_calc_rdreg(nor, nor->program_opcode);
+ writel(reg, reg_base + CQSPI_REG_RD_INSTR);
+
+ writel(to_addr, reg_base + CQSPI_REG_INDIRECTWRSTARTADDR);
+
+ reg = readl(reg_base + CQSPI_REG_SIZE);
+ reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
+ reg |= (nor->addr_width - 1);
+ writel(reg, reg_base + CQSPI_REG_SIZE);
+ return 0;
+}
+
+static __maybe_unused int cqspi_indirect_write_execute(struct spi_nor *nor,
+ const u8 *txbuf, unsigned n_tx)
+{
+ int ret;
+ unsigned int reg = 0;
+ struct cqspi_st *cqspi = nor->priv;
+ void __iomem *reg_base = cqspi->iobase;
+ void __iomem *ahb_base = cqspi->ahb_base;
+ int remaining = (int)n_tx;
+ unsigned int page_size;
+ unsigned int write_bytes;
+
+ page_size = nor->page_size;
+
+ writel(remaining, reg_base + CQSPI_REG_INDIRECTWRBYTES);
+
+ writel(CQSPI_REG_SRAM_THRESHOLD_BYTES, reg_base +
+ CQSPI_REG_INDIRECTWRWATERMARK);
+
+ /* Clear all interrupts. */
+ writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
+
+ cqspi->irq_mask = CQSPI_IRQ_MASK_WR;
+ writel(cqspi->irq_mask, reg_base + CQSPI_REG_IRQMASK);
+
+ writel(CQSPI_REG_INDIRECTWR_START_MASK,
+ reg_base + CQSPI_REG_INDIRECTWR);
+
+ /* Write a page or remaining bytes. */
+ write_bytes = remaining > page_size ? page_size : remaining;
+ /* Fill up the data at the beginning */
+ cqspi_fifo_write(ahb_base, txbuf, write_bytes);
+ txbuf += write_bytes;
+ remaining -= write_bytes;
+
+ while (remaining > 0) {
+ ret = wait_on_timeout(CQSPI_READ_TIMEOUT_MS,
+ readl(reg_base + CQSPI_REG_IRQSTATUS) & cqspi->irq_mask);
+
+ /* Clear all interrupts. */
+ writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
+
+ if (ret < 0) {
+ dev_err(nor->dev, "Indirect write timeout\n");
+ ret = -ETIMEDOUT;
+ goto failwr;
+ }
+
+ write_bytes = remaining > page_size ? page_size : remaining;
+ cqspi_fifo_write(ahb_base, txbuf, write_bytes);
+ txbuf += write_bytes;
+ remaining -= write_bytes;
+
+ writel(cqspi->irq_mask, reg_base + CQSPI_REG_IRQMASK);
+ }
+ ret = wait_on_timeout(CQSPI_READ_TIMEOUT_MS,
+ readl(reg_base + CQSPI_REG_IRQSTATUS) & cqspi->irq_mask);
+
+ /* Clear all interrupts. */
+ writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
+ if (ret < 0) {
+ dev_err(nor->dev, "Indirect write timeout\n");
+ ret = -ETIMEDOUT;
+ goto failwr;
+ }
+
+ /* Check indirect done status */
+ if (wait_on_timeout(CQSPI_TIMEOUT_MS,
+ readl(reg_base + CQSPI_REG_INDIRECTWR)
+ & CQSPI_REG_INDIRECTWR_DONE_MASK)) {
+ dev_err(nor->dev,
+ "Indirect write completion error 0x%08x\n", reg);
+ ret = -ETIMEDOUT;
+ goto failwr;
+ }
+
+ /* Disable interrupt. */
+ writel(0, reg_base + CQSPI_REG_IRQMASK);
+
+ /* Clear indirect completion status */
+ writel(CQSPI_REG_INDIRECTWR_DONE_MASK, reg_base + CQSPI_REG_INDIRECTWR);
+
+ cqspi_wait_idle(cqspi);
+
+ return 0;
+
+failwr:
+ /* Disable interrupt. */
+ writel(0, reg_base + CQSPI_REG_IRQMASK);
+
+ /* Cancel the indirect write */
+ writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
+ reg_base + CQSPI_REG_INDIRECTWR);
+ return ret;
+}
+
+static void cqspi_write(struct spi_nor *nor, loff_t to,
+ size_t len, size_t *retlen, const u_char *buf)
+{
+ int ret;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return;
+
+ ret = cqspi_indirect_write_setup(nor, to);
+ if (ret == 0) {
+ ret = cqspi_indirect_write_execute(nor, buf, len);
+ if (ret == 0)
+ *retlen += len;
+ }
+}
+
+static int cqspi_read(struct spi_nor *nor, loff_t from,
+ size_t len, size_t *retlen, u_char *buf)
+{
+ int ret;
+
+ ret = cqspi_indirect_read_setup(nor, from);
+ if (ret == 0) {
+ ret = cqspi_indirect_read_execute(nor, buf, len);
+ if (ret == 0)
+ *retlen += len;
+ }
+ return ret;
+}
+
+static int cqspi_erase(struct spi_nor *nor, loff_t offs)
+{
+ int ret;
+
+ /* Send write enable, then erase commands. */
+ ret = nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0, 0);
+ if (ret)
+ return ret;
+
+ /* Set up command buffer. */
+ ret = cqspi_command_write_addr(nor, nor->erase_opcode, offs);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static unsigned int calculate_ticks_for_ns(unsigned int ref_clk_hz,
+ unsigned int ns_val)
+{
+ unsigned int ticks;
+
+ ticks = ref_clk_hz;
+ ticks /= 1000;
+ ticks *= ns_val;
+ ticks += 999999;
+ ticks /= 1000000;
+ return ticks;
+}
+
+static void cqspi_delay(struct cqspi_st *cqspi,
+ unsigned int ref_clk_hz, unsigned int sclk_hz)
+{
+ void __iomem *reg_base = cqspi->iobase;
+ struct cqspi_flash_pdata *f_pdata;
+ unsigned int ref_clk_ns;
+ unsigned int sclk_ns;
+ unsigned int tshsl, tchsh, tslch, tsd2d;
+ unsigned int reg;
+ unsigned int tsclk;
+
+ if (cqspi->no_reconfig)
+ return;
+
+ f_pdata = &cqspi->f_pdata[cqspi->current_cs];
+
+ /* Convert to ns. */
+ ref_clk_ns = NSEC_PER_SEC / ref_clk_hz;
+
+ /* Convert to ns. */
+ sclk_ns = NSEC_PER_SEC / sclk_hz;
+
+ /* calculate the number of ref ticks for one sclk tick */
+ tsclk = (ref_clk_hz + sclk_hz - 1) / sclk_hz;
+
+ tshsl = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tshsl_ns);
+ /* this particular value must be at least one sclk */
+ if (tshsl < tsclk)
+ tshsl = tsclk;
+
+ tchsh = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tchsh_ns);
+ tslch = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tslch_ns);
+ tsd2d = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tsd2d_ns);
+
+ reg = ((tshsl & CQSPI_REG_DELAY_TSHSL_MASK)
+ << CQSPI_REG_DELAY_TSHSL_LSB);
+ reg |= ((tchsh & CQSPI_REG_DELAY_TCHSH_MASK)
+ << CQSPI_REG_DELAY_TCHSH_LSB);
+ reg |= ((tslch & CQSPI_REG_DELAY_TSLCH_MASK)
+ << CQSPI_REG_DELAY_TSLCH_LSB);
+ reg |= ((tsd2d & CQSPI_REG_DELAY_TSD2D_MASK)
+ << CQSPI_REG_DELAY_TSD2D_LSB);
+ writel(reg, reg_base + CQSPI_REG_DELAY);
+}
+
+static void cqspi_config_baudrate_div(struct cqspi_st *cqspi,
+ unsigned int ref_clk_hz,
+ unsigned int sclk_hz)
+{
+ void __iomem *reg_base = cqspi->iobase;
+ unsigned int reg;
+ unsigned int div;
+
+ reg = readl(reg_base + CQSPI_REG_CONFIG);
+ reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB);
+
+ div = ref_clk_hz / sclk_hz;
+
+ /* Recalculate the baudrate divisor based on QSPI specification. */
+ if (div > 32)
+ div = 32;
+
+ /* Check if even number. */
+ if (div & 1)
+ div = (div / 2);
+ else
+ div = (div / 2) - 1;
+
+ div = (div & CQSPI_REG_CONFIG_BAUD_MASK) << CQSPI_REG_CONFIG_BAUD_LSB;
+ reg |= div;
+ writel(reg, reg_base + CQSPI_REG_CONFIG);
+}
+
+static void cqspi_readdata_capture(struct cqspi_st *cqspi,
+ unsigned int bypass, unsigned int delay)
+{
+ void __iomem *reg_base = cqspi->iobase;
+ unsigned int reg;
+
+ if (cqspi->no_reconfig)
+ return;
+
+ reg = readl(reg_base + CQSPI_REG_READCAPTURE);
+
+ if (bypass)
+ reg |= (1 << CQSPI_REG_READCAPTURE_BYPASS_LSB);
+ else
+ reg &= ~(1 << CQSPI_REG_READCAPTURE_BYPASS_LSB);
+
+ reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK
+ << CQSPI_REG_READCAPTURE_DELAY_LSB);
+
+ reg |= ((delay & CQSPI_REG_READCAPTURE_DELAY_MASK)
+ << CQSPI_REG_READCAPTURE_DELAY_LSB);
+
+ writel(reg, reg_base + CQSPI_REG_READCAPTURE);
+}
+
+static void cqspi_chipselect(struct cqspi_st *cqspi,
+ unsigned int chip_select,
+ unsigned int decoder_enable)
+{
+ void __iomem *reg_base = cqspi->iobase;
+ unsigned int reg;
+
+ reg = readl(reg_base + CQSPI_REG_CONFIG);
+ if (decoder_enable) {
+ reg |= CQSPI_REG_CONFIG_DECODE_MASK;
+ } else {
+ reg &= ~CQSPI_REG_CONFIG_DECODE_MASK;
+
+ /* Convert CS if without decoder.
+ * CS0 to 4b'1110
+ * CS1 to 4b'1101
+ * CS2 to 4b'1011
+ * CS3 to 4b'0111
+ */
+ chip_select = 0xF & ~(1 << chip_select);
+ }
+
+ reg &= ~(CQSPI_REG_CONFIG_CHIPSELECT_MASK
+ << CQSPI_REG_CONFIG_CHIPSELECT_LSB);
+ reg |= (chip_select & CQSPI_REG_CONFIG_CHIPSELECT_MASK)
+ << CQSPI_REG_CONFIG_CHIPSELECT_LSB;
+ writel(reg, reg_base + CQSPI_REG_CONFIG);
+}
+
+static void cqspi_controller_enable(struct cqspi_st *cqspi)
+{
+ void __iomem *reg_base = cqspi->iobase;
+ unsigned int reg;
+
+ reg = readl(reg_base + CQSPI_REG_CONFIG);
+ reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
+ writel(reg, reg_base + CQSPI_REG_CONFIG);
+}
+
+static void cqspi_controller_disable(struct cqspi_st *cqspi)
+{
+ void __iomem *reg_base = cqspi->iobase;
+ unsigned int reg;
+
+ reg = readl(reg_base + CQSPI_REG_CONFIG);
+ reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
+ writel(reg, reg_base + CQSPI_REG_CONFIG);
+}
+
+static void cqspi_switch_cs(struct cqspi_st *cqspi, unsigned int cs)
+{
+ unsigned int reg;
+ struct cqspi_flash_pdata *f_pdata = &cqspi->f_pdata[cs];
+ void __iomem *reg_base = cqspi->iobase;
+ struct spi_nor *nor = &f_pdata->nor;
+
+ cqspi_controller_disable(cqspi);
+
+ /* configure page size and block size. */
+ reg = readl(reg_base + CQSPI_REG_SIZE);
+ reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
+ reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
+ reg |= (nor->page_size << CQSPI_REG_SIZE_PAGE_LSB);
+ reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
+ reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
+ reg |= (nor->addr_width - 1);
+ writel(reg, reg_base + CQSPI_REG_SIZE);
+
+ /* configure the chip select */
+ cqspi_chipselect(cqspi, cs, cqspi->ext_decoder);
+
+ cqspi_controller_enable(cqspi);
+}
+
+static int cqspi_prep(struct spi_nor *nor, enum spi_nor_ops ops)
+{
+ struct cqspi_st *cqspi = nor->priv;
+ int cs = cqspi_find_chipselect(nor);
+ struct cqspi_flash_pdata *f_pdata;
+ unsigned int sclk;
+
+ /* Switch chip select. */
+ if (cqspi->current_cs != cs) {
+ cqspi->current_cs = cs;
+ cqspi_switch_cs(cqspi, cs);
+ }
+
+ /* Setup baudrate divisor and delays */
+ f_pdata = &cqspi->f_pdata[cqspi->current_cs];
+ sclk = f_pdata->clk_rate;
+ if (cqspi->sclk != sclk) {
+ cqspi->sclk = sclk;
+ cqspi_controller_disable(cqspi);
+ cqspi_config_baudrate_div(cqspi,
+ cqspi->master_ref_clk_hz, sclk);
+ cqspi_delay(cqspi, cqspi->master_ref_clk_hz, sclk);
+ cqspi_readdata_capture(cqspi, 1, f_pdata->read_delay);
+ cqspi_controller_enable(cqspi);
+ }
+ return 0;
+}
+
+static int cqspi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+ int ret;
+
+ cqspi_prep(nor, SPI_NOR_OPS_READ);
+
+ ret = cqspi_command_read(nor, &opcode, 1, buf, len);
+ return ret;
+}
+
+static int cqspi_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len,
+ int write_enable)
+{
+ int ret = 0;
+
+ if (!IS_ENABLED(CONFIG_MTD_WRITE))
+ return -ENOTSUPP;
+
+ cqspi_prep(nor, SPI_NOR_OPS_WRITE);
+
+ ret = cqspi_command_write(nor, opcode, buf, len);
+ return ret;
+}
+
+static int cqspi_of_get_flash_pdata(struct device_d *dev,
+ struct cqspi_flash_pdata *f_pdata,
+ struct device_node *np)
+{
+ struct cqspi_st *cqspi = dev->priv;
+ void __iomem *reg_base = cqspi->iobase;
+
+ if (!np) {
+ f_pdata->block_size = (readl(reg_base + CQSPI_REG_SIZE) >>
+ CQSPI_REG_SIZE_BLOCK_LSB) &
+ CQSPI_REG_SIZE_BLOCK_MASK;
+
+ cqspi->no_reconfig = true;
+
+ return 0;
+ }
+
+ if (of_property_read_u32(np, "cdns,block-size", &f_pdata->block_size)) {
+ dev_err(dev, "couldn't determine block-size\n");
+ return -ENXIO;
+ }
+
+ if (of_property_read_u32(np, "cdns,read-delay", &f_pdata->read_delay)) {
+ dev_err(dev, "couldn't determine read-delay\n");
+ return -ENXIO;
+ }
+
+ if (of_property_read_u32(np, "cdns,tshsl-ns", &f_pdata->tshsl_ns)) {
+ dev_err(dev, "couldn't determine tshsl-ns\n");
+ return -ENXIO;
+ }
+
+ if (of_property_read_u32(np, "cdns,tsd2d-ns", &f_pdata->tsd2d_ns)) {
+ dev_err(dev, "couldn't determine tsd2d-ns\n");
+ return -ENXIO;
+ }
+
+ if (of_property_read_u32(np, "cdns,tchsh-ns", &f_pdata->tchsh_ns)) {
+ dev_err(dev, "couldn't determine tchsh-ns\n");
+ return -ENXIO;
+ }
+
+ if (of_property_read_u32(np, "cdns,tslch-ns", &f_pdata->tslch_ns)) {
+ dev_err(dev, "couldn't determine tslch-ns\n");
+ return -ENXIO;
+ }
+
+ if (of_property_read_u32(np, "spi-max-frequency", &f_pdata->clk_rate)) {
+ dev_err(dev, "couldn't determine spi-max-frequency\n");
+ return -ENXIO;
+ }
+
+ return 0;
+}
+
+static int cqspi_parse_dt(struct cqspi_st *cqspi)
+{
+ struct device_node *np = cqspi->dev->device_node;
+ struct device_d *dev = cqspi->dev;
+
+ if (of_property_read_u32(np, "ext-decoder", &cqspi->ext_decoder)) {
+ dev_err(dev, "couldn't determine ext-decoder\n");
+ return -ENXIO;
+ }
+
+ if (of_property_read_u32(np, "fifo-depth", &cqspi->fifo_depth)) {
+ dev_err(dev, "couldn't determine fifo-depth\n");
+ return -ENXIO;
+ }
+
+ return 0;
+}
+
+static int cqspi_setup_flash(struct device_d *dev,
+ struct cqspi_flash_pdata *f_pdata,
+ struct device_node *np)
+{
+ struct cqspi_st *cqspi = dev->priv;
+ struct mtd_info *mtd;
+ struct spi_nor *nor;
+ int ret;
+
+ ret = cqspi_of_get_flash_pdata(dev, f_pdata, np);
+ if (ret)
+ goto probe_failed;
+
+ nor = &f_pdata->nor;
+ mtd = &f_pdata->mtd;
+
+ nor->mtd = mtd;
+
+ if (np) {
+ nor->dev = xzalloc(sizeof(*nor->dev));
+
+ strcpy(nor->dev->name, np->name);
+
+ nor->dev->device_node = np;
+ nor->dev->id = DEVICE_ID_SINGLE;
+ nor->dev->parent = dev;
+ ret = register_device(nor->dev);
+
+ if (ret)
+ return ret;
+
+ mtd->parent = nor->dev;
+ } else {
+ nor->dev = dev;
+ }
+
+ nor->priv = cqspi;
+ mtd->priv = nor;
+
+ nor->read_reg = cqspi_read_reg;
+ nor->write_reg = cqspi_write_reg;
+ nor->read = cqspi_read;
+ nor->write = cqspi_write;
+ nor->erase = cqspi_erase;
+
+ ret = spi_nor_scan(nor, NULL, SPI_NOR_QUAD);
+ if (ret)
+ goto probe_failed;
+
+ ret = add_mtd_device(mtd, NULL, DEVICE_ID_DYNAMIC);
+ if (ret)
+ goto probe_failed;
+
+ return 0;
+
+probe_failed:
+ dev_err(dev, "probing for flashchip failed\n");
+ return ret;
+
+}
+
+static void cqspi_controller_init(struct cqspi_st *cqspi)
+{
+ cqspi_controller_disable(cqspi);
+
+ /* Configure the remap address register, no remap */
+ writel(0, cqspi->iobase + CQSPI_REG_REMAP);
+
+ /* Disable all interrupts */
+ writel(0, cqspi->iobase + CQSPI_REG_IRQMASK);
+
+ cqspi_controller_enable(cqspi);
+}
+
+static int cqspi_probe(struct device_d *dev)
+{
+ struct device_node *np = dev->device_node;
+ struct cqspi_st *cqspi;
+ struct cadence_qspi_platform_data *pdata = dev->platform_data;
+ int ret;
+
+ cqspi = kzalloc(sizeof(*cqspi), GFP_KERNEL);
+ if (!cqspi)
+ return -ENOMEM;
+
+ cqspi->dev = dev;
+ dev->priv = cqspi;
+
+ if (pdata) {
+ cqspi->ext_decoder = pdata->ext_decoder;
+ cqspi->fifo_depth = pdata->fifo_depth;
+ } else {
+ ret = cqspi_parse_dt(cqspi);
+ if (ret) {
+ dev_err(dev, "Get platform data failed.\n");
+ return -ENODEV;
+ }
+ }
+
+ cqspi->qspi_clk = clk_get(dev, "qspi_clk");
+ if (IS_ERR(cqspi->qspi_clk)) {
+ dev_err(dev, "cannot get qspi clk\n");
+ ret = PTR_ERR(cqspi->qspi_clk);
+ goto probe_failed;
+ }
+ cqspi->master_ref_clk_hz = clk_get_rate(cqspi->qspi_clk);
+
+ clk_enable(cqspi->qspi_clk);
+
+ cqspi->iobase = dev_request_mem_region(dev, 0);
+ if (IS_ERR(cqspi->iobase)) {
+ dev_err(dev, "dev_request_mem_region 0 failed\n");
+ ret = PTR_ERR(cqspi->iobase);
+ goto probe_failed;
+ }
+
+ cqspi->ahb_base = dev_request_mem_region(dev, 1);
+ if (IS_ERR(cqspi->ahb_base)) {
+ dev_err(dev, "dev_request_mem_region 0 failed\n");
+ ret = PTR_ERR(cqspi->ahb_base);
+ goto probe_failed;
+ }
+
+ cqspi_wait_idle(cqspi);
+ cqspi_controller_init(cqspi);
+ cqspi->current_cs = -1;
+ cqspi->sclk = 0;
+
+ if (!dev->device_node) {
+ struct cqspi_flash_pdata *f_pdata;
+
+ f_pdata = &cqspi->f_pdata[0];
+
+ ret = cqspi_setup_flash(dev, f_pdata, NULL);
+ if (ret)
+ goto probe_failed;
+ } else {
+ /* Get flash device data */
+ for_each_available_child_of_node(dev->device_node, np) {
+ struct cqspi_flash_pdata *f_pdata;
+ unsigned int cs;
+ if (of_property_read_u32(np, "reg", &cs)) {
+ dev_err(dev, "couldn't determine chip select\n");
+ return -ENXIO;
+ }
+ if (cs > CQSPI_MAX_CHIPSELECT) {
+ dev_err(dev, "chip select %d out of range\n", cs);
+ return -ENXIO;
+ }
+ f_pdata = &cqspi->f_pdata[cs];
+
+ ret = cqspi_setup_flash(dev, f_pdata, np);
+ if (ret)
+ goto probe_failed;
+ }
+ }
+
+ dev_info(dev, "Cadence QSPI NOR flash driver\n");
+ return 0;
+
+probe_failed:
+ dev_err(dev, "Cadence QSPI NOR probe failed\n");
+ return ret;
+}
+
+static __maybe_unused struct of_device_id cqspi_dt_ids[] = {
+ {.compatible = "cdns,qspi-nor",},
+ { /* end of table */ }
+};
+
+static struct driver_d cqspi_driver = {
+ .name = "cadence_qspi",
+ .probe = cqspi_probe,
+ .of_compatible = DRV_OF_COMPAT(cqspi_dt_ids),
+};
+device_platform_driver(cqspi_driver);
diff --git a/include/platform_data/cadence_qspi.h b/include/platform_data/cadence_qspi.h
new file mode 100644
index 000000000000..4930edce507e
--- /dev/null
+++ b/include/platform_data/cadence_qspi.h
@@ -0,0 +1,9 @@
+#ifndef __INCLUDE_PLATFORM_DATA_CADENCE_QSPI_H
+#define __INCLUDE_PLATFORM_DATA_CADENCE_QSPI_H
+
+struct cadence_qspi_platform_data {
+ unsigned int ext_decoder;
+ unsigned int fifo_depth;
+};
+
+#endif /* __INCLUDE_PLATFORM_DATA_CADENCE_QSPI_H */
--
2.1.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH v2 3/8] ARM: dts: socfpga: add qspi node
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 1/8] mtd: spi-nor: add SPI-NOR framework Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 2/8] mtd: spi-nor: add cadence quadspi driver Steffen Trumtrar
@ 2015-05-28 15:56 ` Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 4/8] ARM: socfpga: socdk add qspi flash Steffen Trumtrar
` (5 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-28 15:56 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
arch/arm/dts/socfpga.dtsi | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm/dts/socfpga.dtsi b/arch/arm/dts/socfpga.dtsi
index afac867c991d..251d87ed4ea2 100644
--- a/arch/arm/dts/socfpga.dtsi
+++ b/arch/arm/dts/socfpga.dtsi
@@ -587,6 +587,21 @@
status = "disabled";
};
+ qspi: spi@ff705000 {
+ compatible = "cdns,qspi-nor";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xff705000 0x1000>,
+ <0xffa00000 0x1000>;
+ interrupts = <0 151 4>;
+ ext-decoder = <0>; /* external decoder */
+ fifo-depth = <128>;
+ clocks = <&qspi_clk>;
+ clock-names = "qspi_clk";
+ status = "disabled";
+ };
+
+
/* Local timer */
timer@fffec600 {
compatible = "arm,cortex-a9-twd-timer";
--
2.1.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH v2 4/8] ARM: socfpga: socdk add qspi flash
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
` (2 preceding siblings ...)
2015-05-28 15:56 ` [PATCH v2 3/8] ARM: dts: socfpga: add qspi node Steffen Trumtrar
@ 2015-05-28 15:56 ` Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 5/8] ARM: socfpga: socrates: " Steffen Trumtrar
` (4 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-28 15:56 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
arch/arm/dts/socfpga_cyclone5_socdk.dts | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm/dts/socfpga_cyclone5_socdk.dts b/arch/arm/dts/socfpga_cyclone5_socdk.dts
index 025d07c18c02..d123bf679ecc 100644
--- a/arch/arm/dts/socfpga_cyclone5_socdk.dts
+++ b/arch/arm/dts/socfpga_cyclone5_socdk.dts
@@ -61,3 +61,24 @@
vmmc-supply = <®ulator_3_3v>;
vqmmc-supply = <®ulator_3_3v>;
};
+
+&qspi {
+ status = "okay";
+
+ flash: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q00";
+ reg = <0>;
+ spi-max-frequency = <108000000>;
+ m25p,fast-read;
+ cdns,page-size = <256>;
+ cdns,block-size = <16>;
+ cdns,read-delay = <4>;
+ cdns,tshsl-ns = <50>;
+ cdns,tsd2d-ns = <50>;
+ cdns,tchsh-ns = <4>;
+ cdns,tslch-ns = <4>;
+ };
+};
+
--
2.1.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH v2 5/8] ARM: socfpga: socrates: add qspi flash
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
` (3 preceding siblings ...)
2015-05-28 15:56 ` [PATCH v2 4/8] ARM: socfpga: socdk add qspi flash Steffen Trumtrar
@ 2015-05-28 15:56 ` Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 6/8] ARM: socfpga: sockit: " Steffen Trumtrar
` (3 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-28 15:56 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
arch/arm/dts/socfpga_cyclone5_socrates.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/dts/socfpga_cyclone5_socrates.dts b/arch/arm/dts/socfpga_cyclone5_socrates.dts
index 7fa5e63076d4..125ad1b8502d 100644
--- a/arch/arm/dts/socfpga_cyclone5_socrates.dts
+++ b/arch/arm/dts/socfpga_cyclone5_socrates.dts
@@ -62,3 +62,23 @@
&mmc {
status = "okay";
};
+
+&qspi {
+ status = "okay";
+
+ flash: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q00";
+ reg = <0>;
+ spi-max-frequency = <100000000>;
+ m25p,fast-read;
+ cdns,page-size = <256>;
+ cdns,block-size = <16>;
+ cdns,read-delay = <4>;
+ cdns,tshsl-ns = <50>;
+ cdns,tsd2d-ns = <50>;
+ cdns,tchsh-ns = <4>;
+ cdns,tslch-ns = <4>;
+ };
+};
--
2.1.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH v2 6/8] ARM: socfpga: sockit: add qspi flash
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
` (4 preceding siblings ...)
2015-05-28 15:56 ` [PATCH v2 5/8] ARM: socfpga: socrates: " Steffen Trumtrar
@ 2015-05-28 15:56 ` Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 7/8] ARM: socfpga: xload: support qspi bootsource Steffen Trumtrar
` (2 subsequent siblings)
8 siblings, 0 replies; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-28 15:56 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
arch/arm/dts/socfpga_cyclone5_sockit.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/dts/socfpga_cyclone5_sockit.dts b/arch/arm/dts/socfpga_cyclone5_sockit.dts
index e8e00aedfc10..1c3fb4d39c0b 100644
--- a/arch/arm/dts/socfpga_cyclone5_sockit.dts
+++ b/arch/arm/dts/socfpga_cyclone5_sockit.dts
@@ -119,3 +119,23 @@
interrupts = <0x0 0xa6 0x4>;
};
};
+
+&qspi {
+ status = "okay";
+
+ flash: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q00";
+ reg = <0>;
+ spi-max-frequency = <108000000>;
+ m25p,fast-read;
+ cdns,page-size = <256>;
+ cdns,block-size = <16>;
+ cdns,read-delay = <4>;
+ cdns,tshsl-ns = <50>;
+ cdns,tsd2d-ns = <50>;
+ cdns,tchsh-ns = <4>;
+ cdns,tslch-ns = <4>;
+ };
+};
--
2.1.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH v2 7/8] ARM: socfpga: xload: support qspi bootsource
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
` (5 preceding siblings ...)
2015-05-28 15:56 ` [PATCH v2 6/8] ARM: socfpga: sockit: " Steffen Trumtrar
@ 2015-05-28 15:56 ` Steffen Trumtrar
2015-05-28 15:56 ` [PATCH v2 8/8] mtd: m25p80: use the SPI nor framework Steffen Trumtrar
2015-05-29 7:25 ` [PATCH v2 0/8] Socfpga: QSPI support Sascha Hauer
8 siblings, 0 replies; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-28 15:56 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
Documentation/boards/socfpga.rst | 56 ++++++++++++++++++++--
arch/arm/mach-socfpga/include/mach/generic.h | 5 ++
arch/arm/mach-socfpga/include/mach/socfpga-regs.h | 2 +
arch/arm/mach-socfpga/xload.c | 58 ++++++++++++++++++++++-
4 files changed, 115 insertions(+), 6 deletions(-)
diff --git a/Documentation/boards/socfpga.rst b/Documentation/boards/socfpga.rst
index e956bccbe24a..358e5ab91030 100644
--- a/Documentation/boards/socfpga.rst
+++ b/Documentation/boards/socfpga.rst
@@ -11,10 +11,34 @@ build the ``socfpga-xload_defconfig``; for second stage use the normal
Bootstrapping
-------------
-The supported bootsource is a SD card. The Boot ROM searches for a partition of
-type A2 and loads what it finds there. When barebox is placed in such a partition
-it will then itself try and mount the second partition of the SD card, which must
-be of type FAT32. On this partition barebox searches for a file called barebox.bin.
+The supported bootsources are: SD card and QSPI.
+
+Bootsource selection
+^^^^^^^^^^^^^^^^^^^^
+
++--------------+-----------+-----------+
+| Board | BSEL[2:0] | CSEL[1:0] |
++==============+===========+===========+
+| Sockit SD | 0b100 | 0b00 |
++--------------+-----------+-----------+
+| Sockit QSPI | 0b110 | 0b00 |
++--------------+-----------+-----------+
+| Socrates SD | 0b101 | 0b11 |
++--------------+-----------+-----------+
+| Socrates QSPI| 0b111 | 0b11 |
++--------------+-----------+-----------+
+| SocDK SD | 0b100 | 0b00 |
++--------------+-----------+-----------+
+| SocDK QSPI | 0b110 | 0b00 |
++--------------+-----------+-----------+
+
+SD card
+^^^^^^^
+
+The Boot ROM searches for a partition of type A2 and loads what it finds there.
+When barebox is placed in such a partition it will then itself try and mount the
+second partition of the SD card, which must be of type FAT32. On this partition
+barebox searches for a file called barebox.bin.
To boot barebox on a Terasic SoCkit, the procedure is as follows (sdb1 is the A2 and
sdb2 the FAT32 partition)::
@@ -34,6 +58,30 @@ proceed with::
For the EBV Socrates use ``images/barebox-socfpga-socrates(-xload).img`` instead.
+QSPI
+^^^^
+
+The Boot ROM loads the preloader starting from address 0x0 on the QSPI flash.
+barebox then searches for a barebox image at the 256K offset and loads it.
+
+The default bootsource is SD card, so to change that to QSPI, you have to::
+
+ make socfpga-xload_defconfig
+ make menuconfig
+
+And then select the options `MTD` and `SPI_CADENCE_QUADSPI`. Now::
+
+ make
+ cat images/barebox-socfpga-<board>-xload.img > /dev/mtd0
+
+For barebox itself, the build step is like for SD card. The resulting image has to be
+written to the offset 256K.
+
+Warning! There is a known issue with booting from QSPI and doing Cold/Warm-Resets.
+Please consult `Rocketboards <http://rocketboards.org/foswiki/Documentation/SocBoardQspiBoot#Serial_Flash_Challenges>`_
+to see how to fix this.
+
+
Updating handoff files
----------------------
diff --git a/arch/arm/mach-socfpga/include/mach/generic.h b/arch/arm/mach-socfpga/include/mach/generic.h
index 2f5cda0d0263..1f4247f803e3 100644
--- a/arch/arm/mach-socfpga/include/mach/generic.h
+++ b/arch/arm/mach-socfpga/include/mach/generic.h
@@ -15,4 +15,9 @@ static inline void __udelay(unsigned us)
for (i = 0; i < us * 3; i++);
}
+struct socfpga_barebox_part {
+ unsigned int nor_offset;
+ unsigned int nor_size;
+};
+
#endif /* __MACH_SOCFPGA_GENERIC_H */
diff --git a/arch/arm/mach-socfpga/include/mach/socfpga-regs.h b/arch/arm/mach-socfpga/include/mach/socfpga-regs.h
index b124ed675cfc..e88daf718917 100644
--- a/arch/arm/mach-socfpga/include/mach/socfpga-regs.h
+++ b/arch/arm/mach-socfpga/include/mach/socfpga-regs.h
@@ -2,6 +2,8 @@
#define __MACH_SOCFPGA_REGS_H
#define CYCLONE5_SDMMC_ADDRESS 0xff704000
+#define CYCLONE5_QSPI_CTRL_ADDRESS 0xff705000
+#define CYCLONE5_QSPI_DATA_ADDRESS 0xffa00000
#define CYCLONE5_FPGAMGRREGS_ADDRESS 0xff706000
#define CYCLONE5_GPIO0_BASE 0xff708000
#define CYCLONE5_GPIO1_BASE 0xff709000
diff --git a/arch/arm/mach-socfpga/xload.c b/arch/arm/mach-socfpga/xload.c
index 3380092168ae..272896b6bda0 100644
--- a/arch/arm/mach-socfpga/xload.c
+++ b/arch/arm/mach-socfpga/xload.c
@@ -1,3 +1,4 @@
+#include <platform_data/cadence_qspi.h>
#include <platform_data/dw_mmc.h>
#include <bootsource.h>
#include <bootstrap.h>
@@ -14,11 +15,19 @@
#include <linux/stat.h>
#include <linux/clk.h>
+#include <mach/generic.h>
#include <mach/system-manager.h>
#include <mach/socfpga-regs.h>
+struct socfpga_barebox_part *barebox_part;
+
+static struct socfpga_barebox_part default_part = {
+ .nor_offset = SZ_256K,
+ .nor_size = SZ_1M,
+};
+
enum socfpga_clks {
- timer, mmc, uart, clk_max
+ timer, mmc, qspi_clk, uart, clk_max
};
static struct clk *clks[clk_max];
@@ -35,6 +44,43 @@ static void socfpga_mmc_init(void)
IORESOURCE_MEM, &mmc_pdata);
}
+#if defined(CONFIG_SPI_CADENCE_QUADSPI)
+static struct cadence_qspi_platform_data qspi_pdata = {
+ .ext_decoder = 0,
+ .fifo_depth = 128,
+};
+
+static __maybe_unused void add_cadence_qspi_device(int id, resource_size_t ctrl,
+ resource_size_t data, void *pdata)
+{
+ struct resource *res;
+
+ res = xzalloc(sizeof(struct resource) * 2);
+ res[0].start = ctrl;
+ res[0].end = ctrl + 0x100 - 1;
+ res[0].flags = IORESOURCE_MEM;
+ res[1].start = data;
+ res[1].end = data + 0x100 - 1;
+ res[1].flags = IORESOURCE_MEM;
+
+ add_generic_device_res("cadence_qspi", id, res, 2, pdata);
+}
+
+static __maybe_unused void socfpga_qspi_init(void)
+{
+ clks[qspi_clk] = clk_fixed("qspi_clk", 370000000);
+ clkdev_add_physbase(clks[qspi_clk], CYCLONE5_QSPI_CTRL_ADDRESS, NULL);
+ clkdev_add_physbase(clks[qspi_clk], CYCLONE5_QSPI_DATA_ADDRESS, NULL);
+ add_cadence_qspi_device(0, CYCLONE5_QSPI_CTRL_ADDRESS,
+ CYCLONE5_QSPI_DATA_ADDRESS, &qspi_pdata);
+}
+#else
+static void socfpga_qspi_init(void)
+{
+ return;
+}
+#endif
+
static struct NS16550_plat uart_pdata = {
.clock = 100000000,
.shift = 2,
@@ -62,10 +108,19 @@ static __noreturn int socfpga_xload(void)
enum bootsource bootsource = bootsource_get();
void *buf;
+ if (!barebox_part)
+ barebox_part = &default_part;
+
switch (bootsource) {
case BOOTSOURCE_MMC:
+ socfpga_mmc_init();
buf = bootstrap_read_disk("disk0.1", "fat");
break;
+ case BOOTSOURCE_SPI:
+ socfpga_qspi_init();
+ buf = bootstrap_read_devfs("mtd0", false, barebox_part->nor_offset,
+ barebox_part->nor_size, SZ_1M);
+ break;
default:
pr_err("unknown bootsource %d\n", bootsource);
hang();
@@ -88,7 +143,6 @@ static int socfpga_devices_init(void)
barebox_set_model("SoCFPGA");
socfpga_timer_init();
socfpga_uart_init();
- socfpga_mmc_init();
barebox_main = socfpga_xload;
--
2.1.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH v2 8/8] mtd: m25p80: use the SPI nor framework
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
` (6 preceding siblings ...)
2015-05-28 15:56 ` [PATCH v2 7/8] ARM: socfpga: xload: support qspi bootsource Steffen Trumtrar
@ 2015-05-28 15:56 ` Steffen Trumtrar
2015-06-16 5:48 ` Antony Pavlov
2015-05-29 7:25 ` [PATCH v2 0/8] Socfpga: QSPI support Sascha Hauer
8 siblings, 1 reply; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-28 15:56 UTC (permalink / raw)
To: barebox; +Cc: Steffen Trumtrar
Use the spi-nor framework for the m25p80 driver to de-duplicate the code base
and follow along with the linux kernel version, so bugfixes or features can be
easier integrated.
Based on the Linux v4.1-rc3 version of m25p80.c.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
---
drivers/mtd/devices/Kconfig | 2 +-
drivers/mtd/devices/m25p80.c | 998 +++++++------------------------------------
2 files changed, 166 insertions(+), 834 deletions(-)
diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig
index 7f9c30625844..345c348c692b 100644
--- a/drivers/mtd/devices/Kconfig
+++ b/drivers/mtd/devices/Kconfig
@@ -21,7 +21,7 @@ config MTD_DATAFLASH_WRITE_VERIFY
config MTD_M25P80
tristate "Support most SPI Flash chips (AT26DF, M25P, W25X, ...)"
- depends on SPI
+ depends on MTD_SPI_NOR
help
This enables access to most modern SPI flash chips, used for
program and data storage. Series supported include Atmel AT26DF,
diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
index 095a4ca0936c..c941767de94c 100644
--- a/drivers/mtd/devices/m25p80.c
+++ b/drivers/mtd/devices/m25p80.c
@@ -25,774 +25,202 @@
#include <errno.h>
#include <linux/err.h>
#include <clock.h>
-#include <linux/math64.h>
-#include <linux/mtd/cfi.h>
#include <linux/mtd/mtd.h>
+#include <linux/mtd/spi-nor.h>
+#include <linux/mod_devicetable.h>
-/* Flash opcodes. */
-#define OPCODE_WREN 0x06 /* Write enable */
-#define OPCODE_RDSR 0x05 /* Read status register */
-#define OPCODE_WRSR 0x01 /* Write status register 1 byte */
-#define OPCODE_NORM_READ 0x03 /* Read data bytes (low frequency) */
-#define OPCODE_FAST_READ 0x0b /* Read data bytes (high frequency) */
-#define OPCODE_PP 0x02 /* Page program (up to 256 bytes) */
-#define OPCODE_BE_4K 0x20 /* Erase 4KiB block */
-#define OPCODE_BE_32K 0x52 /* Erase 32KiB block */
-#define OPCODE_CHIP_ERASE 0xc7 /* Erase whole flash chip */
-#define OPCODE_SE 0xd8 /* Sector erase (usually 64KiB) */
-#define OPCODE_RDID 0x9f /* Read JEDEC ID */
-
-/* Used for SST flashes only. */
-#define OPCODE_BP 0x02 /* Byte program */
-#define OPCODE_WRDI 0x04 /* Write disable */
-#define OPCODE_AAI_WP 0xad /* Auto address increment word program */
-
-/* Used for Macronix flashes only. */
-#define OPCODE_EN4B 0xb7 /* Enter 4-byte mode */
-#define OPCODE_EX4B 0xe9 /* Exit 4-byte mode */
-
-/* Used for Spansion flashes only. */
-#define OPCODE_BRWR 0x17 /* Bank register write */
-
-/* Status Register bits. */
-#define SR_WIP 1 /* Write in progress */
-#define SR_WEL 2 /* Write enable latch */
-/* meaning of other SR_* bits may differ between vendors */
-#define SR_BP0 4 /* Block protect 0 */
-#define SR_BP1 8 /* Block protect 1 */
-#define SR_BP2 0x10 /* Block protect 2 */
-#define SR_SRWD 0x80 /* SR write protect */
-
-/* Define max times to check status register before we give up. */
-#define MAX_READY_WAIT 40 /* M25P16 specs 40s max chip erase */
#define MAX_CMD_SIZE 6
-#define JEDEC_MFR(_jedec_id) ((_jedec_id) >> 16)
-
-/****************************************************************************/
-
-#define SPI_NAME_SIZE 32
-
struct m25p {
struct spi_device *spi;
+ struct spi_nor spi_nor;
struct mtd_info mtd;
- u16 page_size;
- unsigned sector_size;
- u16 addr_width;
- u8 erase_opcode;
- u8 erase_opcode_4k;
- u8 *command;
+ u8 command[MAX_CMD_SIZE];
};
-static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd)
-{
- return container_of(mtd, struct m25p, mtd);
-}
-
-/****************************************************************************/
-
-/*
- * Internal helper functions
- */
-
-/*
- * Read the status register, returning its value in the location
- * Return the status register value.
- * Returns negative if error occurred.
- */
-static int read_sr(struct m25p *flash)
-{
- ssize_t retval;
- u8 code = OPCODE_RDSR;
- u8 val;
-
- retval = spi_write_then_read(flash->spi, &code, 1, &val, 1);
-
- if (retval < 0) {
- dev_err(&flash->spi->dev, "error %d reading SR\n",
- (int) retval);
- return retval;
- }
-
- return val;
-}
-
-/*
- * Write status register 1 byte
- * Returns negative if error occurred.
- */
-static int write_sr(struct m25p *flash, u8 val)
-{
- flash->command[0] = OPCODE_WRSR;
- flash->command[1] = val;
-
- return spi_write(flash->spi, flash->command, 2);
-}
-
-/*
- * Set write enable latch with Write Enable command.
- * Returns negative if error occurred.
- */
-static inline int write_enable(struct m25p *flash)
-{
- u8 code = OPCODE_WREN;
-
- return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
-}
-
-/*
- * Send write disble instruction to the chip.
- */
-static inline int write_disable(struct m25p *flash)
-{
- u8 code = OPCODE_WRDI;
-
- return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
-}
-
-/*
- * Enable/disable 4-byte addressing mode.
- */
-static inline int set_4byte(struct m25p *flash, u32 jedec_id, int enable)
-{
- switch (JEDEC_MFR(jedec_id)) {
- case CFI_MFR_MACRONIX:
- flash->command[0] = enable ? OPCODE_EN4B : OPCODE_EX4B;
- return spi_write(flash->spi, flash->command, 1);
- default:
- /* Spansion style */
- flash->command[0] = OPCODE_BRWR;
- flash->command[1] = enable << 7;
- return spi_write(flash->spi, flash->command, 2);
- }
-}
-
-/*
- * Service routine to read status register until ready, or timeout occurs.
- * Returns non-zero if error.
- */
-static int wait_till_ready(struct m25p *flash)
+static int m25p80_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
{
- int sr;
- uint64_t timer_start;
+ struct m25p *flash = nor->priv;
+ struct spi_device *spi = flash->spi;
+ int ret;
- timer_start = get_time_ns();
+ ret = spi_write_then_read(spi, &code, 1, val, len);
+ if (ret < 0)
+ dev_err(&spi->dev, "error %d reading %x\n", ret, code);
- do {
- if ((sr = read_sr(flash)) < 0)
- break;
- else if (!(sr & SR_WIP))
- return 0;
-
- } while (!(is_timeout(timer_start, MAX_READY_WAIT * SECOND)));
-
- return -ETIMEDOUT;
-}
-
-/*
- * Erase the whole flash memory
- *
- * Returns 0 if successful, non-zero otherwise.
- */
-static int erase_chip(struct m25p *flash)
-{
- dev_dbg(&flash->spi->dev, "%s %lldKiB\n",
- __func__, (long long)(flash->mtd.size >> 10));
-
- /* Wait until finished previous write command. */
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
-
- /* Send write enable, then erase commands. */
- write_enable(flash);
-
- /* Set up command buffer. */
- flash->command[0] = OPCODE_CHIP_ERASE;
-
- spi_write(flash->spi, flash->command, 1);
-
- return 0;
+ return ret;
}
-static void m25p_addr2cmd(struct m25p *flash, unsigned int addr, u8 *cmd)
+static void m25p_addr2cmd(struct spi_nor *nor, unsigned int addr, u8 *cmd)
{
/* opcode is in cmd[0] */
- cmd[1] = addr >> (flash->addr_width * 8 - 8);
- cmd[2] = addr >> (flash->addr_width * 8 - 16);
- cmd[3] = addr >> (flash->addr_width * 8 - 24);
- cmd[4] = addr >> (flash->addr_width * 8 - 32);
+ cmd[1] = addr >> (nor->addr_width * 8 - 8);
+ cmd[2] = addr >> (nor->addr_width * 8 - 16);
+ cmd[3] = addr >> (nor->addr_width * 8 - 24);
+ cmd[4] = addr >> (nor->addr_width * 8 - 32);
}
-static int m25p_cmdsz(struct m25p *flash)
+static int m25p_cmdsz(struct spi_nor *nor)
{
- return 1 + flash->addr_width;
-}
-
-/*
- * Erase one sector of flash memory at offset ``offset'' which is any
- * address within the sector which should be erased.
- *
- * Returns 0 if successful, non-zero otherwise.
- */
-static int erase_sector(struct m25p *flash, u32 offset, u32 command)
-{
- dev_dbg(&flash->spi->dev, "%s %dKiB at 0x%08x\n",
- __func__, flash->mtd.erasesize / 1024, offset);
-
- /* Wait until finished previous write command. */
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
-
- /* Send write enable, then erase commands. */
- write_enable(flash);
-
- /* Set up command buffer. */
- flash->command[0] = command;
- m25p_addr2cmd(flash, offset, flash->command);
-
- spi_write(flash->spi, flash->command, m25p_cmdsz(flash));
-
- return 0;
+ return 1 + nor->addr_width;
}
-/****************************************************************************/
-
-/*
- * MTD implementation
- */
-
-/*
- * Erase an address range on the flash chip. The address range may extend
- * one or more erase sectors. Return an error is there is a problem erasing.
- */
-static int m25p80_erase(struct mtd_info *mtd, struct erase_info *instr)
+static int m25p80_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len,
+ int wr_en)
{
- struct m25p *flash = mtd_to_m25p(mtd);
- u32 addr;
- uint32_t rem;
- uint64_t len;
-
- dev_dbg(&flash->spi->dev, "%s at 0x%llx, len %lld\n",
- __func__, (long long)instr->addr,
- (long long)instr->len);
-
- div_u64_rem(instr->len, mtd->erasesize, &rem);
- if (rem)
- return -EINVAL;
-
- addr = instr->addr;
- len = instr->len;
-
- /* whole-chip erase? */
- if (len == flash->mtd.size) {
- if (erase_chip(flash)) {
- instr->state = MTD_ERASE_FAILED;
- return -EIO;
- }
- return 0;
- }
-
- if (flash->erase_opcode_4k) {
- while (len && (addr & (flash->sector_size - 1))) {
- if (ctrlc())
- return -EINTR;
- if (erase_sector(flash, addr, flash->erase_opcode_4k))
- return -EIO;
- addr += mtd->erasesize;
- len -= mtd->erasesize;
- }
-
- while (len >= flash->sector_size) {
- if (ctrlc())
- return -EINTR;
- if (erase_sector(flash, addr, flash->erase_opcode))
- return -EIO;
- addr += flash->sector_size;
- len -= flash->sector_size;
- }
-
- while (len) {
- if (ctrlc())
- return -EINTR;
- if (erase_sector(flash, addr, flash->erase_opcode_4k))
- return -EIO;
- addr += mtd->erasesize;
- len -= mtd->erasesize;
- }
- } else {
- while (len) {
- if (ctrlc())
- return -EINTR;
- if (erase_sector(flash, addr, flash->erase_opcode))
- return -EIO;
-
- if (len <= mtd->erasesize)
- break;
- addr += mtd->erasesize;
- len -= mtd->erasesize;
- }
- }
+ struct m25p *flash = nor->priv;
+ struct spi_device *spi = flash->spi;
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
+ flash->command[0] = opcode;
+ if (buf)
+ memcpy(&flash->command[1], buf, len);
- instr->state = MTD_ERASE_DONE;
- mtd_erase_callback(instr);
-
- return 0;
+ return spi_write(spi, flash->command, len + 1);
}
-/*
- * Read an address range from the flash chip. The address range
- * may be any size provided it is within the physical boundaries.
- */
-static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf)
+static void m25p80_write(struct spi_nor *nor, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
{
- struct m25p *flash = mtd_to_m25p(mtd);
- struct spi_transfer t[2];
+ struct m25p *flash = nor->priv;
+ struct spi_device *spi = flash->spi;
+ struct spi_transfer t[2] = {};
struct spi_message m;
- int fast_read = 0;
-
- if (flash->spi->max_speed_hz >= 25000000)
- fast_read = 1;
+ int cmd_sz = m25p_cmdsz(nor);
spi_message_init(&m);
- memset(t, 0, (sizeof t));
- /* NOTE:
- * OPCODE_FAST_READ (if available) is faster.
- * Should add 1 byte DUMMY_BYTE.
- */
+ if (nor->program_opcode == SPINOR_OP_AAI_WP && nor->sst_write_second)
+ cmd_sz = 1;
+
+ flash->command[0] = nor->program_opcode;
+ m25p_addr2cmd(nor, to, flash->command);
+
t[0].tx_buf = flash->command;
- t[0].len = m25p_cmdsz(flash) + fast_read;
+ t[0].len = cmd_sz;
spi_message_add_tail(&t[0], &m);
- t[1].rx_buf = buf;
+ t[1].tx_buf = buf;
t[1].len = len;
spi_message_add_tail(&t[1], &m);
- /* Wait till previous write/erase is done. */
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
-
- /* FIXME switch to OPCODE_FAST_READ. It's required for higher
- * clocks; and at this writing, every chip this driver handles
- * supports that opcode.
- */
+ spi_sync(spi, &m);
- /* Set up the write data buffer. */
- flash->command[0] = fast_read ? OPCODE_FAST_READ : OPCODE_NORM_READ;
- m25p_addr2cmd(flash, from, flash->command);
-
- spi_sync(flash->spi, &m);
-
- *retlen = m.actual_length - m25p_cmdsz(flash) - fast_read;
-
- return 0;
+ *retlen += m.actual_length - cmd_sz;
}
/*
- * Write an address range to the flash chip. Data must be written in
- * FLASH_PAGESIZE chunks. The address range may be any size provided
- * it is within the physical boundaries.
+ * Read an address range from the nor chip. The address range
+ * may be any size provided it is within the physical boundaries.
*/
-static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf)
+static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
{
- struct m25p *flash = mtd_to_m25p(mtd);
- u32 page_offset, page_size;
+ struct m25p *flash = nor->priv;
+ struct spi_device *spi = flash->spi;
struct spi_transfer t[2];
struct spi_message m;
+ unsigned int dummy = nor->read_dummy;
- dev_dbg(&flash->spi->dev, "m25p80_write %ld bytes at 0x%08llx\n",
- (unsigned long)len, to);
+ /* convert the dummy cycles to the number of bytes */
+ dummy /= 8;
spi_message_init(&m);
memset(t, 0, (sizeof t));
+ flash->command[0] = nor->read_opcode;
+ m25p_addr2cmd(nor, from, flash->command);
+
t[0].tx_buf = flash->command;
- t[0].len = m25p_cmdsz(flash);
+ t[0].len = m25p_cmdsz(nor) + dummy;
spi_message_add_tail(&t[0], &m);
- t[1].tx_buf = buf;
+ t[1].rx_buf = buf;
+ t[1].len = len;
spi_message_add_tail(&t[1], &m);
- /* Wait until finished previous write command. */
- if (wait_till_ready(flash))
- return -ETIMEDOUT;
-
- write_enable(flash);
-
- /* Set up the opcode in the write buffer. */
- flash->command[0] = OPCODE_PP;
- m25p_addr2cmd(flash, to, flash->command);
-
- page_offset = to & (flash->page_size - 1);
-
- /* do all the bytes fit onto one page? */
- if (page_offset + len <= flash->page_size) {
- t[1].len = len;
-
- spi_sync(flash->spi, &m);
-
- *retlen = m.actual_length - m25p_cmdsz(flash);
- } else {
- u32 i;
-
- /* the size of data remaining on the first page */
- page_size = flash->page_size - page_offset;
-
- t[1].len = page_size;
- spi_sync(flash->spi, &m);
-
- *retlen = m.actual_length - m25p_cmdsz(flash);
-
- /* write everything in flash->page_size chunks */
- for (i = page_size; i < len; i += page_size) {
- page_size = len - i;
- if (page_size > flash->page_size)
- page_size = flash->page_size;
-
- /* write the next page to flash */
- m25p_addr2cmd(flash, to + i, flash->command);
-
- t[1].tx_buf = buf + i;
- t[1].len = page_size;
-
- wait_till_ready(flash);
-
- write_enable(flash);
-
- spi_sync(flash->spi, &m);
-
- *retlen += m.actual_length - m25p_cmdsz(flash);
- }
- }
+ spi_sync(spi, &m);
+ *retlen = m.actual_length - m25p_cmdsz(nor) - dummy;
return 0;
}
-static int sst_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf)
+static int m25p80_erase(struct spi_nor *nor, loff_t offset)
{
- struct m25p *flash = mtd_to_m25p(mtd);
- struct spi_transfer t[2];
- struct spi_message m;
- size_t actual;
- int cmd_sz, ret;
+ struct m25p *flash = nor->priv;
- dev_dbg(&flash->spi->dev, "%s to 0x%08x, len %zd\n",
- __func__, (u32)to, len);
+ dev_dbg(nor->dev, "%dKiB at 0x%08x\n",
+ flash->mtd.erasesize / 1024, (u32)offset);
- spi_message_init(&m);
- memset(t, 0, (sizeof t));
+ /* Set up command buffer. */
+ flash->command[0] = nor->erase_opcode;
+ m25p_addr2cmd(nor, offset, flash->command);
- t[0].tx_buf = flash->command;
- t[0].len = m25p_cmdsz(flash);
- spi_message_add_tail(&t[0], &m);
+ spi_write(flash->spi, flash->command, m25p_cmdsz(nor));
- t[1].tx_buf = buf;
- spi_message_add_tail(&t[1], &m);
-
- /* Wait until finished previous write command. */
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
-
- write_enable(flash);
-
- actual = to % 2;
- /* Start write from odd address. */
- if (actual) {
- flash->command[0] = OPCODE_BP;
- m25p_addr2cmd(flash, to, flash->command);
-
- /* write one byte. */
- t[1].len = 1;
- spi_sync(flash->spi, &m);
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
- *retlen += m.actual_length - m25p_cmdsz(flash);
- }
- to += actual;
-
- flash->command[0] = OPCODE_AAI_WP;
- m25p_addr2cmd(flash, to, flash->command);
-
- /* Write out most of the data here. */
- cmd_sz = m25p_cmdsz(flash);
- for (; actual < len - 1; actual += 2) {
- t[0].len = cmd_sz;
- /* write two bytes. */
- t[1].len = 2;
- t[1].tx_buf = buf + actual;
-
- spi_sync(flash->spi, &m);
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
- *retlen += m.actual_length - cmd_sz;
- cmd_sz = 1;
- to += 2;
- }
- write_disable(flash);
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
-
- /* Write out trailing byte if it exists. */
- if (actual != len) {
- write_enable(flash);
- flash->command[0] = OPCODE_BP;
- m25p_addr2cmd(flash, to, flash->command);
- t[0].len = m25p_cmdsz(flash);
- t[1].len = 1;
- t[1].tx_buf = buf + actual;
-
- spi_sync(flash->spi, &m);
- ret = wait_till_ready(flash);
- if (ret)
- goto time_out;
- *retlen += m.actual_length - m25p_cmdsz(flash);
- write_disable(flash);
- }
-
-time_out:
- return ret;
+ return 0;
}
-/****************************************************************************/
-
/*
- * SPI device driver setup and teardown
- */
-
-struct flash_info {
- /* JEDEC id zero means "no ID" (most older chips); otherwise it has
- * a high byte of zero plus three data bytes: the manufacturer id,
- * then a two byte device id.
- */
- u32 jedec_id;
- u16 ext_id;
-
- /* The size listed here is what works with OPCODE_SE, which isn't
- * necessarily called a "sector" by the vendor.
- */
- unsigned sector_size;
- u16 n_sectors;
-
- u16 page_size;
- u16 addr_width;
-
- u16 flags;
-#define SECT_4K 0x01 /* OPCODE_BE_4K works uniformly */
-#define M25P_NO_ERASE 0x02 /* No erase command needed */
-};
-
-#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
- ((unsigned long)&(struct flash_info) { \
- .jedec_id = (_jedec_id), \
- .ext_id = (_ext_id), \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = 256, \
- .flags = (_flags), \
- })
-
-#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width) \
- ((unsigned long)&(struct flash_info) { \
- .sector_size = (_sector_size), \
- .n_sectors = (_n_sectors), \
- .page_size = (_page_size), \
- .addr_width = (_addr_width), \
- .flags = M25P_NO_ERASE, \
- })
-
-/* NOTE: double check command sets and memory organization when you add
- * more flash chips. This current list focusses on newer chips, which
- * have been converging on command sets which including JEDEC ID.
+ * Do NOT add to this array without reading the following:
+ *
+ * Historically, many flash devices are bound to this driver by their name. But
+ * since most of these flash are compatible to some extent, and their
+ * differences can often be differentiated by the JEDEC read-ID command, we
+ * encourage new users to add support to the spi-nor library, and simply bind
+ * against a generic string here (e.g., "nor-jedec").
+ *
+ * Many flash names are kept here in this list (as well as in spi-nor.c) to
+ * keep them available as module aliases for existing platforms.
*/
static const struct platform_device_id m25p_ids[] = {
- /* Atmel -- some are (confusingly) marketed as "DataFlash" */
- { "at25fs010", INFO(0x1f6601, 0, 32 * 1024, 4, SECT_4K) },
- { "at25fs040", INFO(0x1f6604, 0, 64 * 1024, 8, SECT_4K) },
-
- { "at25df041a", INFO(0x1f4401, 0, 64 * 1024, 8, SECT_4K) },
- { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) },
- { "at25df641", INFO(0x1f4800, 0, 64 * 1024, 128, SECT_4K) },
-
- { "at26f004", INFO(0x1f0400, 0, 64 * 1024, 8, SECT_4K) },
- { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) },
- { "at26df161a", INFO(0x1f4601, 0, 64 * 1024, 32, SECT_4K) },
- { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) },
-
- { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) },
-
- /* EON -- en25xxx */
- { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) },
- { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) },
- { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) },
- { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) },
- { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
-
- /* Everspin */
- { "mr25h256", CAT25_INFO( 32 * 1024, 1, 256, 2) },
-
- /* Intel/Numonyx -- xxxs33b */
- { "160s33b", INFO(0x898911, 0, 64 * 1024, 32, 0) },
- { "320s33b", INFO(0x898912, 0, 64 * 1024, 64, 0) },
- { "640s33b", INFO(0x898913, 0, 64 * 1024, 128, 0) },
- { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
-
- /* Macronix */
- { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) },
- { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) },
- { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) },
- { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) },
- { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, 0) },
- { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, 0) },
- { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
- { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
- { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) },
- { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
-
- /* Micron */
- { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
- { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) },
- { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) },
- { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) },
-
- /* Spansion -- single (large) sector size only, at least
- * for the chips listed here (without boot sectors).
- */
- { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, 0) },
- { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, 0) },
- { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, 0) },
- { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, 0) },
- { "s25fl512s", INFO(0x010220, 0x4d00, 256 * 1024, 256, 0) },
- { "s70fl01gs", INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) },
- { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) },
- { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) },
- { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, 0) },
- { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, 0) },
- { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) },
- { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) },
- { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) },
- { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) },
- { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) },
- { "s25fl016k", INFO(0xef4015, 0, 64 * 1024, 32, SECT_4K) },
- { "s25fl064k", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
-
- /* SST -- large erase sizes are "overlays", "sectors" are 4K */
- { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K) },
- { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K) },
- { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K) },
- { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K) },
- { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K) },
- { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K) },
- { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K) },
- { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K) },
-
- /* ST Microelectronics -- newer production may have feature updates */
- { "m25p05", INFO(0x202010, 0, 32 * 1024, 2, 0) },
- { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) },
- { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) },
- { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) },
- { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) },
- { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) },
- { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) },
- { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) },
- { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) },
- { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, 0) },
-
- { "m25p05-nonjedec", INFO(0, 0, 32 * 1024, 2, 0) },
- { "m25p10-nonjedec", INFO(0, 0, 32 * 1024, 4, 0) },
- { "m25p20-nonjedec", INFO(0, 0, 64 * 1024, 4, 0) },
- { "m25p40-nonjedec", INFO(0, 0, 64 * 1024, 8, 0) },
- { "m25p80-nonjedec", INFO(0, 0, 64 * 1024, 16, 0) },
- { "m25p16-nonjedec", INFO(0, 0, 64 * 1024, 32, 0) },
- { "m25p32-nonjedec", INFO(0, 0, 64 * 1024, 64, 0) },
- { "m25p64-nonjedec", INFO(0, 0, 64 * 1024, 128, 0) },
- { "m25p128-nonjedec", INFO(0, 0, 256 * 1024, 64, 0) },
-
- { "m45pe10", INFO(0x204011, 0, 64 * 1024, 2, 0) },
- { "m45pe80", INFO(0x204014, 0, 64 * 1024, 16, 0) },
- { "m45pe16", INFO(0x204015, 0, 64 * 1024, 32, 0) },
-
- { "m25pe20", INFO(0x208012, 0, 64 * 1024, 4, 0) },
- { "m25pe80", INFO(0x208014, 0, 64 * 1024, 16, 0) },
- { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) },
-
- { "m25px32", INFO(0x207116, 0, 64 * 1024, 64, SECT_4K) },
- { "m25px32-s0", INFO(0x207316, 0, 64 * 1024, 64, SECT_4K) },
- { "m25px32-s1", INFO(0x206316, 0, 64 * 1024, 64, SECT_4K) },
- { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) },
-
- /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */
- { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) },
- { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) },
- { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) },
- { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) },
- { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) },
- { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) },
- { "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64, SECT_4K) },
- { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
- { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
- { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) },
- { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) },
-
- /* Catalyst / On Semiconductor -- non-JEDEC */
- { "cat25c11", CAT25_INFO( 16, 8, 16, 1) },
- { "cat25c03", CAT25_INFO( 32, 8, 16, 2) },
- { "cat25c09", CAT25_INFO( 128, 8, 32, 2) },
- { "cat25c17", CAT25_INFO( 256, 8, 32, 2) },
- { "cat25128", CAT25_INFO(2048, 8, 64, 2) },
+ {"at25fs010"}, {"at25fs040"}, {"at25df041a"}, {"at25df321a"},
+ {"at25df641"}, {"at26f004"}, {"at26df081a"}, {"at26df161a"},
+ {"at26df321"}, {"at45db081d"},
+ {"en25f32"}, {"en25p32"}, {"en25q32b"}, {"en25p64"},
+ {"en25q64"}, {"en25qh128"}, {"en25qh256"},
+ {"f25l32pa"},
+ {"mr25h256"}, {"mr25h10"},
+ {"gd25q32"}, {"gd25q64"},
+ {"160s33b"}, {"320s33b"}, {"640s33b"},
+ {"mx25l2005a"}, {"mx25l4005a"}, {"mx25l8005"}, {"mx25l1606e"},
+ {"mx25l3205d"}, {"mx25l3255e"}, {"mx25l6405d"}, {"mx25l12805d"},
+ {"mx25l12855e"},{"mx25l25635e"},{"mx25l25655e"},{"mx66l51235l"},
+ {"mx66l1g55g"},
+ {"n25q064"}, {"n25q128a11"}, {"n25q128a13"}, {"n25q256a"},
+ {"n25q512a"}, {"n25q512ax3"}, {"n25q00"},
+ {"pm25lv512"}, {"pm25lv010"}, {"pm25lq032"},
+ {"s25sl032p"}, {"s25sl064p"}, {"s25fl256s0"}, {"s25fl256s1"},
+ {"s25fl512s"}, {"s70fl01gs"}, {"s25sl12800"}, {"s25sl12801"},
+ {"s25fl129p0"}, {"s25fl129p1"}, {"s25sl004a"}, {"s25sl008a"},
+ {"s25sl016a"}, {"s25sl032a"}, {"s25sl064a"}, {"s25fl008k"},
+ {"s25fl016k"}, {"s25fl064k"}, {"s25fl132k"},
+ {"sst25vf040b"},{"sst25vf080b"},{"sst25vf016b"},{"sst25vf032b"},
+ {"sst25vf064c"},{"sst25wf512"}, {"sst25wf010"}, {"sst25wf020"},
+ {"sst25wf040"},
+ {"m25p05"}, {"m25p10"}, {"m25p20"}, {"m25p40"},
+ {"m25p80"}, {"m25p16"}, {"m25p32"}, {"m25p64"},
+ {"m25p128"}, {"n25q032"},
+ {"m25p05-nonjedec"}, {"m25p10-nonjedec"}, {"m25p20-nonjedec"},
+ {"m25p40-nonjedec"}, {"m25p80-nonjedec"}, {"m25p16-nonjedec"},
+ {"m25p32-nonjedec"}, {"m25p64-nonjedec"}, {"m25p128-nonjedec"},
+ {"m45pe10"}, {"m45pe80"}, {"m45pe16"},
+ {"m25pe20"}, {"m25pe80"}, {"m25pe16"},
+ {"m25px16"}, {"m25px32"}, {"m25px32-s0"}, {"m25px32-s1"},
+ {"m25px64"}, {"m25px80"},
+ {"w25x10"}, {"w25x20"}, {"w25x40"}, {"w25x80"},
+ {"w25x16"}, {"w25x32"}, {"w25q32"}, {"w25q32dw"},
+ {"w25x64"}, {"w25q64"}, {"w25q80"}, {"w25q80bl"},
+ {"w25q128"}, {"w25q256"}, {"cat25c11"},
+ {"cat25c03"}, {"cat25c09"}, {"cat25c17"}, {"cat25128"},
+
+ /*
+ * Generic support for SPI NOR that can be identified by the JEDEC READ
+ * ID opcode (0x9F). Use this, if possible.
+ */
+ {"nor-jedec"},
{ },
};
-static const struct platform_device_id *jedec_probe(struct spi_device *spi)
-{
- int tmp;
- u8 code = OPCODE_RDID;
- u8 id[5];
- u32 jedec;
- u16 ext_jedec;
- struct flash_info *info;
-
- /* JEDEC also defines an optional "extended device information"
- * string for after vendor-specific data, after the three bytes
- * we use here. Supporting some chips might require using it.
- */
- tmp = spi_write_then_read(spi, &code, 1, id, 5);
- if (tmp < 0) {
- dev_dbg(&spi->dev, "%s: error %d reading JEDEC ID\n",
- dev_name(&spi->dev), tmp);
- return ERR_PTR(tmp);
- }
- jedec = id[0];
- jedec = jedec << 8;
- jedec |= id[1];
- jedec = jedec << 8;
- jedec |= id[2];
-
- ext_jedec = id[3] << 8 | id[4];
-
- for (tmp = 0; tmp < ARRAY_SIZE(m25p_ids) - 1; tmp++) {
- info = (void *)m25p_ids[tmp].driver_data;
- if (info->jedec_id == jedec) {
- if (info->ext_id != 0 && info->ext_id != ext_jedec)
- continue;
- return &m25p_ids[tmp];
- }
- }
- dev_err(&spi->dev, "unrecognized JEDEC id %06x\n", jedec);
- return ERR_PTR(-ENODEV);
-}
-
-
/*
* board specific setup should have ensured the SPI clock used here
* matches what the READ command supports, at least until this driver
@@ -801,164 +229,68 @@ static const struct platform_device_id *jedec_probe(struct spi_device *spi)
static int m25p_probe(struct device_d *dev)
{
struct spi_device *spi = (struct spi_device *)dev->type_data;
- const struct platform_device_id *id = NULL;
struct flash_platform_data *data;
struct m25p *flash;
- struct flash_info *info = NULL;
- unsigned i;
- unsigned do_jdec_probe = 1;
- char *flashname = NULL;
- const char *typename = NULL;
+ struct spi_nor *nor;
+ enum read_mode mode = SPI_NOR_NORMAL;
+ char *flash_name = NULL;
int device_id;
+ int ret;
- /* Platform data helps sort out which chip type we have, as
- * well as how this board partitions it. If we don't have
- * a chip ID, try the JEDEC id commands; they'll work for most
- * newer chips, even if we don't recognize the particular chip.
- */
data = dev->platform_data;
- if (data && data->type)
- typename = data->type;
- else if (dev->id_entry)
- typename = dev->id_entry->name;
-
- if (typename) {
- const struct platform_device_id *plat_id;
-
- for (i = 0; i < ARRAY_SIZE(m25p_ids) - 1; i++) {
- plat_id = &m25p_ids[i];
- if (strcmp(typename, plat_id->name))
- continue;
- break;
- }
-
- if (i < ARRAY_SIZE(m25p_ids) - 1) {
- id = plat_id;
- info = (void *)id->driver_data;
- /* If flash type is provided but the memory is not
- * JEDEC compliant, don't try to probe the JEDEC id */
- if (!info->jedec_id)
- do_jdec_probe = 0;
- } else
- dev_warn(&spi->dev, "unrecognized id %s\n", typename);
- }
-
- if (do_jdec_probe) {
- const struct platform_device_id *jid;
-
- jid = jedec_probe(spi);
- if (IS_ERR(jid)) {
- return PTR_ERR(jid);
- } else if (jid != id) {
- /*
- * JEDEC knows better, so overwrite platform ID. We
- * can't trust partitions any longer, but we'll let
- * mtd apply them anyway, since some partitions may be
- * marked read-only, and we don't want to lose that
- * information, even if it's not 100% accurate.
- */
- if (id)
- dev_warn(dev, "found %s, expected %s\n",
- jid->name, id->name);
-
- id = jid;
- info = (void *)jid->driver_data;
- }
- }
flash = xzalloc(sizeof *flash);
- flash->command = xmalloc(MAX_CMD_SIZE);
+ nor = &flash->spi_nor;
+
+ /* install the hooks */
+ nor->read = m25p80_read;
+ nor->write = m25p80_write;
+ nor->erase = m25p80_erase;
+ nor->write_reg = m25p80_write_reg;
+ nor->read_reg = m25p80_read_reg;
+
+ nor->dev = dev;
+ nor->mtd = &flash->mtd;
+ nor->priv = flash;
+
+ flash->mtd.priv = nor;
+ flash->mtd.parent = &spi->dev;
flash->spi = spi;
+
dev->priv = (void *)flash;
- /*
- * Atmel, SST and Intel/Numonyx serial flash tend to power
- * up with the software protection bits set
- */
-
- if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ATMEL ||
- JEDEC_MFR(info->jedec_id) == CFI_MFR_INTEL ||
- JEDEC_MFR(info->jedec_id) == CFI_MFR_SST) {
- write_enable(flash);
- write_sr(flash, 0);
- }
+
+ if (data && data->name)
+ flash->mtd.name = data->name;
+
+ if (data && data->type)
+ flash_name = data->type;
+ else if (data && data->name)
+ flash_name = data->name;
+ else if (dev->id_entry)
+ flash_name = dev->id_entry->name;
+ else
+ flash_name = NULL; /* auto-detect */
+
+ ret = spi_nor_scan(nor, flash_name, mode);
+ if (ret)
+ return ret;
device_id = DEVICE_ID_SINGLE;
if (dev->device_node) {
const char *alias = of_alias_get(dev->device_node);
if (alias)
- flashname = xstrdup(alias);
+ flash_name = xstrdup(alias);
} else if (data && data->name) {
- flashname = data->name;
+ flash_name = data->name;
}
- if (!flashname) {
+ if (!flash_name) {
device_id = DEVICE_ID_DYNAMIC;
- flashname = "m25p";
- }
-
- flash->mtd.type = MTD_NORFLASH;
- flash->mtd.writesize = 1;
- flash->mtd.flags = MTD_CAP_NORFLASH;
- flash->mtd.size = (uint64_t)info->sector_size * info->n_sectors;
- flash->mtd.erase = m25p80_erase;
- flash->mtd.read = m25p80_read;
-
- /* sst flash chips use AAI word program */
- if (IS_ENABLED(CONFIG_MTD_SST25L) && JEDEC_MFR(info->jedec_id) == CFI_MFR_SST)
- flash->mtd.write = sst_write;
- else
- flash->mtd.write = m25p80_write;
-
- /* prefer "small sector" erase if possible */
- if (info->flags & SECT_4K) {
- flash->erase_opcode_4k = OPCODE_BE_4K;
- flash->erase_opcode = OPCODE_SE;
- flash->mtd.erasesize = 4096;
- } else {
- flash->erase_opcode = OPCODE_SE;
- flash->mtd.erasesize = info->sector_size;
- }
-
- if (info->flags & M25P_NO_ERASE)
- flash->mtd.flags |= MTD_NO_ERASE;
-
- flash->mtd.parent = &spi->dev;
- flash->page_size = info->page_size;
- flash->sector_size = info->sector_size;
-
- if (info->addr_width)
- flash->addr_width = info->addr_width;
- else {
- /* enable 4-byte addressing if the device exceeds 16MiB */
- if (flash->mtd.size > 0x1000000) {
- flash->addr_width = 4;
- set_4byte(flash, info->jedec_id, 1);
- } else
- flash->addr_width = 3;
+ flash_name = "m25p";
}
- dev_info(dev, "%s (%lld Kbytes)\n", id->name,
- (long long)flash->mtd.size >> 10);
-
- dev_dbg(dev, "mtd .name = %s, .size = 0x%llx (%lldMiB) "
- ".erasesize = 0x%.8x (%uKiB) .numeraseregions = %d\n",
- flash->mtd.name,
- (long long)flash->mtd.size, (long long)(flash->mtd.size >> 20),
- flash->mtd.erasesize, flash->mtd.erasesize / 1024,
- flash->mtd.numeraseregions);
-
- if (flash->mtd.numeraseregions)
- for (i = 0; i < flash->mtd.numeraseregions; i++)
- dev_dbg(dev, "mtd.eraseregions[%d] = { .offset = 0x%llx, "
- ".erasesize = 0x%.8x (%uKiB), "
- ".numblocks = %d }\n",
- i, (long long)flash->mtd.eraseregions[i].offset,
- flash->mtd.eraseregions[i].erasesize,
- flash->mtd.eraseregions[i].erasesize / 1024,
- flash->mtd.eraseregions[i].numblocks);
-
- return add_mtd_device(&flash->mtd, flashname, device_id);
+ return add_mtd_device(&flash->mtd, flash_name, device_id);
}
static __maybe_unused struct of_device_id m25p80_dt_ids[] = {
--
2.1.4
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v2 8/8] mtd: m25p80: use the SPI nor framework
2015-05-28 15:56 ` [PATCH v2 8/8] mtd: m25p80: use the SPI nor framework Steffen Trumtrar
@ 2015-06-16 5:48 ` Antony Pavlov
2015-06-17 6:05 ` Sascha Hauer
0 siblings, 1 reply; 13+ messages in thread
From: Antony Pavlov @ 2015-06-16 5:48 UTC (permalink / raw)
To: Steffen Trumtrar; +Cc: barebox
On Thu, 28 May 2015 17:56:07 +0200
Steffen Trumtrar <s.trumtrar@pengutronix.de> wrote:
> Use the spi-nor framework for the m25p80 driver to de-duplicate the code base
> and follow along with the linux kernel version, so bugfixes or features can be
> easier integrated.
>
> Based on the Linux v4.1-rc3 version of m25p80.c.
>
> Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
> ---
> drivers/mtd/devices/Kconfig | 2 +-
> drivers/mtd/devices/m25p80.c | 998 +++++++------------------------------------
> 2 files changed, 166 insertions(+), 834 deletions(-)
>
> diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
> index 095a4ca0936c..c941767de94c 100644
> --- a/drivers/mtd/devices/m25p80.c
> +++ b/drivers/mtd/devices/m25p80.c
...
> + {"w25q128"}, {"w25q256"}, {"cat25c11"},
> + {"cat25c03"}, {"cat25c09"}, {"cat25c17"}, {"cat25128"},
> +
> + /*
> + * Generic support for SPI NOR that can be identified by the JEDEC READ
> + * ID opcode (0x9F). Use this, if possible.
> + */
> + {"nor-jedec"},
> { },
> };
Please fix whitespaces here.
Please use checkpatch.pl on your patches before submitting!
--
Best regards,
Antony Pavlov
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v2 8/8] mtd: m25p80: use the SPI nor framework
2015-06-16 5:48 ` Antony Pavlov
@ 2015-06-17 6:05 ` Sascha Hauer
0 siblings, 0 replies; 13+ messages in thread
From: Sascha Hauer @ 2015-06-17 6:05 UTC (permalink / raw)
To: Antony Pavlov; +Cc: barebox, Steffen Trumtrar
On Tue, Jun 16, 2015 at 08:48:51AM +0300, Antony Pavlov wrote:
> On Thu, 28 May 2015 17:56:07 +0200
> Steffen Trumtrar <s.trumtrar@pengutronix.de> wrote:
>
> > Use the spi-nor framework for the m25p80 driver to de-duplicate the code base
> > and follow along with the linux kernel version, so bugfixes or features can be
> > easier integrated.
> >
> > Based on the Linux v4.1-rc3 version of m25p80.c.
> >
> > Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
> > ---
> > drivers/mtd/devices/Kconfig | 2 +-
> > drivers/mtd/devices/m25p80.c | 998 +++++++------------------------------------
> > 2 files changed, 166 insertions(+), 834 deletions(-)
> >
> > diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
> > index 095a4ca0936c..c941767de94c 100644
> > --- a/drivers/mtd/devices/m25p80.c
> > +++ b/drivers/mtd/devices/m25p80.c
>
> ...
>
> > + {"w25q128"}, {"w25q256"}, {"cat25c11"},
> > + {"cat25c03"}, {"cat25c09"}, {"cat25c17"}, {"cat25128"},
> > +
> > + /*
> > + * Generic support for SPI NOR that can be identified by the JEDEC READ
> > + * ID opcode (0x9F). Use this, if possible.
> > + */
> > + {"nor-jedec"},
> > { },
> > };
>
> Please fix whitespaces here.
>
> Please use checkpatch.pl on your patches before submitting!
Uh, yes, there are quite some spaces instead of tabs in this file. I
just committed a patch fixing these.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v2 0/8] Socfpga: QSPI support
2015-05-28 15:55 [PATCH v2 0/8] Socfpga: QSPI support Steffen Trumtrar
` (7 preceding siblings ...)
2015-05-28 15:56 ` [PATCH v2 8/8] mtd: m25p80: use the SPI nor framework Steffen Trumtrar
@ 2015-05-29 7:25 ` Sascha Hauer
2015-05-29 7:49 ` Steffen Trumtrar
8 siblings, 1 reply; 13+ messages in thread
From: Sascha Hauer @ 2015-05-29 7:25 UTC (permalink / raw)
To: Steffen Trumtrar; +Cc: barebox
On Thu, May 28, 2015 at 05:55:59PM +0200, Steffen Trumtrar wrote:
> Hi!
>
> This series adds support for reading,writing and booting from Quad SPI
> flash chips on the SoCFPFGA platform.
>
> The driver is based on a patch for linux, which is still in development.
> As this driver uses the spi-nor framework, this is imported into barebox, too.
> To deduplicate the code base, the m25p80 is also converted to use the spi-nor
> framework.
>
> With the QSPI driver in place, support for booting from it is also added.
> As the preloader barebox doesn't have a devicetree to go from, the driver doesn't
> touch the registers that have already been set up successfully by the Boot ROM code.
> If there ever is any other user of the Cadence QSPI core, that does not have a
> devicetree to probe from, platform code might have to be added for this initialization.
> As there isn't at the moment, I chose to not bother with this.
>
> The cadence-qspi was tested on the Socrates, Sockit and Socdk.
> The m25p80 was tested as "m25p80" on a Phycore AM335x SOM.
Applied, thanks.
Please look out for trailing blank lines next time. There are some of
them in the dts changes I manually fixed up this time.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v2 0/8] Socfpga: QSPI support
2015-05-29 7:25 ` [PATCH v2 0/8] Socfpga: QSPI support Sascha Hauer
@ 2015-05-29 7:49 ` Steffen Trumtrar
0 siblings, 0 replies; 13+ messages in thread
From: Steffen Trumtrar @ 2015-05-29 7:49 UTC (permalink / raw)
To: Sascha Hauer; +Cc: barebox
On Fri, May 29, 2015 at 09:25:24AM +0200, Sascha Hauer wrote:
> On Thu, May 28, 2015 at 05:55:59PM +0200, Steffen Trumtrar wrote:
> > Hi!
> >
> > This series adds support for reading,writing and booting from Quad SPI
> > flash chips on the SoCFPFGA platform.
> >
> > The driver is based on a patch for linux, which is still in development.
> > As this driver uses the spi-nor framework, this is imported into barebox, too.
> > To deduplicate the code base, the m25p80 is also converted to use the spi-nor
> > framework.
> >
> > With the QSPI driver in place, support for booting from it is also added.
> > As the preloader barebox doesn't have a devicetree to go from, the driver doesn't
> > touch the registers that have already been set up successfully by the Boot ROM code.
> > If there ever is any other user of the Cadence QSPI core, that does not have a
> > devicetree to probe from, platform code might have to be added for this initialization.
> > As there isn't at the moment, I chose to not bother with this.
> >
> > The cadence-qspi was tested on the Socrates, Sockit and Socdk.
> > The m25p80 was tested as "m25p80" on a Phycore AM335x SOM.
>
> Applied, thanks.
>
> Please look out for trailing blank lines next time. There are some of
> them in the dts changes I manually fixed up this time.
>
Oh, sorry. I didn't catch them...
Thanks,
Steffen
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 13+ messages in thread