[PATCH 1/3] ARM: i.MX: IIM: Add functions to access fuses field wise

[PATCH 1/3] ARM: i.MX: IIM: Add functions to access fuses field wise

[Sascha Hauer]

Accessing the IIM registers is cumbersome. The fuses are documented with
different register strides and there is no header file available, so the
different fields have to be read in the datasheets and translated into
the barebox format over and over again. This patch adds a header file
which has defines for the various fuses (for i.MX25 only so far, but
others can be added later) along with C functions to read/write the
fields.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-imx/iim.c                        |  57 ++++++
 arch/arm/mach-imx/include/mach/iim.h           |  19 ++
 arch/arm/mach-imx/include/mach/imx25-fusemap.h | 272 +++++++++++++++++++++++++
 3 files changed, 348 insertions(+)
 create mode 100644 arch/arm/mach-imx/include/mach/imx25-fusemap.h

diff --git a/arch/arm/mach-imx/iim.c b/arch/arm/mach-imx/iim.c
index ecaa7e6..3aba02f 100644
--- a/arch/arm/mach-imx/iim.c
+++ b/arch/arm/mach-imx/iim.c
@@ -34,6 +34,7 @@
 #include <mach/imx51-regs.h>
 #include <mach/imx53-regs.h>
 #include <mach/clock-imx51_53.h>
+#include <mach/imx25-fusemap.h>
 
 #define DRIVERNAME	"imx_iim"
 #define IIM_NUM_BANKS	8
@@ -65,6 +66,62 @@ struct imx_iim_drvdata {
 
 static struct iim_priv *imx_iim;
 
+static void imx_iim_field_decode(uint32_t field, unsigned *bank, unsigned *byte,
+				 unsigned *bit, unsigned *mask)
+{
+	unsigned width;
+
+	*bank = (field >> IIM_BANK_MASK_SHIFT) & ((1 << IIM_BANK_MASK_WIDTH) - 1);
+	*byte = (field >> IIM_BYTE_MASK_SHIFT) & ((1 << IIM_BYTE_MASK_WIDTH) - 1);
+	*bit = (field >> IIM_BIT_MASK_SHIFT) & ((1 << IIM_BIT_MASK_WIDTH) - 1);
+	width = ((field >> IIM_WIDTH_MASK_SHIFT) & ((1 << IIM_WIDTH_MASK_WIDTH) - 1)) + 1;
+	*mask = (1 << width) - 1;
+}
+
+int imx_iim_read_field(uint32_t field, unsigned *value)
+{
+	unsigned bank, byte, bit, mask;
+	int ret;
+	unsigned v;
+
+	if (!imx_iim)
+		return -ENODEV;
+
+	imx_iim_field_decode(field, &bank, &byte, &bit, &mask);
+
+	dev_dbg(&imx_iim->dev, "read_field: 0x%08x bank %d byte %d bit %d width 0x%x\n",
+		field, bank, byte, bit, mask);
+
+	ret = regmap_read(imx_iim->bank[bank]->map, byte, &v);
+	if (ret < 0)
+		return ret;
+
+	v >>= bit;
+	v &= mask;
+
+	*value = v;
+
+	return 0;
+}
+
+int imx_iim_write_field(uint32_t field, unsigned value)
+{
+	unsigned bank, byte, bit, mask;
+
+	if (!imx_iim)
+		return -ENODEV;
+
+	imx_iim_field_decode(field, &bank, &byte, &bit, &mask);
+
+	value &= mask;
+	value <<= bit;
+
+	dev_dbg(&imx_iim->dev, "write_field: 0x%08x bank %d byte %d bit %d width 0x%x\n",
+	       field, bank, byte, bit, mask);
+
+	return regmap_write(imx_iim->bank[bank]->map, byte, value);
+}
+
 static int imx_iim_fuse_sense(struct iim_bank *bank, unsigned int row)
 {
 	struct iim_priv *iim = bank->iim;
diff --git a/arch/arm/mach-imx/include/mach/iim.h b/arch/arm/mach-imx/include/mach/iim.h
index 1d28149..f63712e 100644
--- a/arch/arm/mach-imx/include/mach/iim.h
+++ b/arch/arm/mach-imx/include/mach/iim.h
@@ -81,4 +81,23 @@ static inline int imx25_iim_register_fec_ethaddr(void)
 	return 0;
 }
 
+#define IIM_BANK_MASK_WIDTH	3
+#define IIM_BANK_MASK_SHIFT	0
+#define IIM_BANK(n)		(((n) & ((1 << IIM_BANK_MASK_WIDTH) - 1)) << IIM_BANK_MASK_SHIFT)
+
+#define IIM_BYTE_MASK_WIDTH	5
+#define IIM_BYTE_MASK_SHIFT	IIM_BANK_MASK_WIDTH
+#define IIM_BYTE(n)		((((n) >> 2) & ((1 << IIM_BYTE_MASK_WIDTH) - 1)) << IIM_BYTE_MASK_SHIFT)
+
+#define IIM_BIT_MASK_WIDTH	3
+#define IIM_BIT_MASK_SHIFT	(IIM_BYTE_MASK_SHIFT + IIM_BYTE_MASK_WIDTH)
+#define IIM_BIT(n)		(((n) & ((1 << IIM_BIT_MASK_WIDTH) - 1)) << IIM_BIT_MASK_SHIFT)
+
+#define IIM_WIDTH_MASK_WIDTH	3
+#define IIM_WIDTH_MASK_SHIFT	(IIM_BIT_MASK_SHIFT + IIM_BIT_MASK_WIDTH)
+#define IIM_WIDTH(n)		((((n) - 1) & ((1 << IIM_WIDTH_MASK_WIDTH) - 1)) << IIM_WIDTH_MASK_SHIFT)
+
+int imx_iim_read_field(uint32_t field, unsigned *value);
+int imx_iim_write_field(uint32_t field, unsigned value);
+
 #endif /* __MACH_IMX_IIM_H */
diff --git a/arch/arm/mach-imx/include/mach/imx25-fusemap.h b/arch/arm/mach-imx/include/mach/imx25-fusemap.h
new file mode 100644
index 0000000..749b0d1
--- /dev/null
+++ b/arch/arm/mach-imx/include/mach/imx25-fusemap.h
@@ -0,0 +1,272 @@
+#ifndef __MACH_IMX25_FUSEMAP_H
+#define __MACH_IMX25_FUSEMAP_H
+
+#include <mach/iim.h>
+
+/* Fuse bank write protect */
+#define IMX25_IIM_FBWP(bank)		(IIM_BANK(bank) | IIM_BYTE(0) | IIM_BIT(7))
+/* Fuse Bank Override Protect */
+#define IMX25_IIM_FBOP(bank)		(IIM_BANK(bank) | IIM_BYTE(0) | IIM_BIT(6))
+/* Fuse Bank Read Protect */
+#define IMX25_IIM_FBRP(bank)		(IIM_BANK(bank) | IIM_BYTE(0) | IIM_BIT(5))
+/* Tester fuses. Burnt on the tester at the end of the wafer sort, locks bank0, rows 001C-003C */
+#define IMX25_IIM_TESTER_LOCK		(IIM_BANK(0) | IIM_BYTE(0) | IIM_BIT(4))
+/* Fuse Banks Explicit Sense Protect */
+#define IMX25_IIM_FBESP(bank)		(IIM_BANK(bank) | IIM_BYTE(0) | IIM_BIT(3))
+/* Locking row 0068-007C, fusebank0 */
+#define IMX25_IIM_MAC_ADDR_LOCK		(IIM_BANK(0) | IIM_BYTE(0) | IIM_BIT(2))
+/* Locking rows 0008 0054-0064, fusebank0 */
+#define IMX25_IIM_TRIM_LOCK		(IIM_BANK(0) | IIM_BYTE(0) | IIM_BIT(1))
+/* Locking rows 0004, 000C-0018, 0040-0044, fusebank0 */
+#define IMX25_IIM_BOOT_LOCK		(IIM_BANK(0) | IIM_BYTE(0) | IIM_BIT(0))
+/* Disabling the Secure JTAG Controller module clock */
+#define IMX25_IIM_SJC_DISABLE		(IIM_BANK(0) | IIM_BYTE(4) | IIM_BIT(7))
+
+/* Controls the security mode of the JTAG debug interface */
+#define IMX25_IIM_JTAG_SMODE		(IIM_BANK(0) | IIM_BYTE(4) | IIM_BIT(5) | IIM_WIDTH(2))
+
+/* Disable SCC debug through SJC */
+#define IMX25_IIM_JTAG_SCC		(IIM_BANK(0) | IIM_BYTE(4) | IIM_BIT(4))
+
+/* JTAG HAB Enable Override (1 = HAB may not enable JTAG debug access */
+#define IMX25_IIM_JTAG_HEO		(IIM_BANK(0) | IIM_BYTE(4) | IIM_BIT(3))
+
+/* Secure JTAG Re-enable.
+ * 0 Secure JTAG Bypass fuse is not overridden (secure JTAG bypass is allowed)
+ * 1 Secure JTAG Bypass fuse is overridden (secure JTAG bypass is not allowed)
+ */
+#define IMX25_IIM_SEC_JTAG_RE		(IIM_BANK(0) | IIM_BYTE(4) | IIM_BIT(1))
+
+/* JTAG Debug Security Bypass.
+ * 0 JTAG Security bypass is not active
+ * 1 JTAG Security bypass is active
+ */
+#define IMX25_IIM_JTAG_BP		(IIM_BANK(0) | IIM_BYTE(4) | IIM_BIT(0))
+
+/*  High Temperature Detect Configuration. A field in DryIce Analog Configuration Register (DACR) */
+#define IMX25_IIM_HTDC			(IIM_BANK(0) | IIM_BYTE(8) | IIM_BIT(3) | IIM_WIDTH(3))
+
+/*  Low Temperature Detect Configuration. A field in DryIce Analog Configuration Register (DACR) */
+#define IMX25_IIM_LTDC			(IIM_BANK(0) | IIM_BYTE(8) | IIM_BIT(0) | IIM_WIDTH(3))
+
+ /*  Choosing the specific eSDHC, CSPI or I2C controller for booting from. */
+#define IMX25_IIM_BT_SRC		(IIM_BANK(0) | IIM_BYTE(0xc) | IIM_BIT(6) | IIM_WIDTH(2))
+
+/* SLC/MLC NAND device. (Former BT_ECC_SEL fuse) Also used as a fast boot mode indication for eMMC 4.3 protocol.
+ *	If the bootable device is NAND then
+ *		0 SLC NAND device
+ *		1 MLC NAND device
+ *	If the bootable device is MMC then
+ *		0 Do not use eMMC fast boot mode
+ *		1 Use eMMC fast boot mode
+ */
+#define IMX25_IIM_BT_MLC_SEL		(IIM_BANK(0) | IIM_BYTE(0xc) | IIM_BIT(5))
+
+/* Specifies the size of spare bytes for 4KB page size NAND Flash devices.
+ *	If the bootable device is NAND then
+ *		0 128 bytes spare (Samsung) (4-IIM_BIT ECC)
+ *		1 218 bytes spare (Micron, Toshiba) (8-IIM_BIT ECC)
+ *	If the bootable device is SD then
+ *		0 ‘FAST_BOOT’ IIM_BIT 29 in ACMD41 argument is 0
+ *		1 ‘FAST_BOOT’ IIM_BIT 29 in ACMD41 argument is 1
+ */
+#define IMX25_IIM_BT_SPARE_SIZE		(IIM_BANK(0) | IIM_BYTE(0xc) | IIM_BIT(2))
+
+ /* Bypassing a pullup on D+ line in case of LPB.
+  *	1 No pullup on D+ line.
+  */
+#define IMX25_IIM_BT_DPLUS_BYPASS	(IIM_BANK(0) | IIM_BYTE(0xc) | IIM_BIT(1))
+
+/* USB boot source selection. Has a corresponding GPIO pin.
+ *	0 USB OTG Internal PHY (UTMI)
+ *	1 USB OTG External PHY (ULPI)
+ */
+#define IMX25_IIM_BT_USB_SRC		(IIM_BANK(0) | IIM_BYTE(0xc) | IIM_BIT(0))
+
+/* NAND Flash Page Size.
+ *	If BT_MEM_CTL = NAND Flash, then
+ *		00 512 bytes
+ *		01 2K bytes
+ *		10 4K bytes
+ *		11 Reserved
+ */
+#define IMX25_IIM_BT_PAGE_SIZE		(IIM_BANK(0) | IIM_BYTE(0x10) | IIM_BIT(5) | IIM_WIDTH(2))
+
+/* Selects whether EEPROM device is used for load of configuration DCD data
+ *	0 Use EEPROM DCD
+ *	1 Do not use EEPROM DCD
+ */
+#define IMX25_IIM_BT_EEPROM_CFG		(IIM_BANK(0) | IIM_BYTE(0x10) | IIM_BIT(4))
+
+/*  GPIO Boot Select. Determines whether certain boot fuse values are controlled from GPIO pins or IIM.
+ *	0 The fuse values are determined by GPIO pins
+ *	1 The fuse values are determined by fuses
+ */
+#define IMX25_IIM_GPIO_BT_SEL		(IIM_BANK(0) | IIM_BYTE(0x10) | IIM_BIT(3))
+
+/* Security Type.
+ *	001 Engineering (allows any code to be flashed and executed, even if does not have a valid signature)
+ *	100 Security Disabled (forinternal/testing use)
+ *	Others Production (Security On)
+ */
+#define IMX25_IIM_HAB_TYPE		(IIM_BANK(0) | IIM_BYTE(0x10) | IIM_BIT(0) | IIM_WIDTH(3))
+
+/* Boot Memory Type.
+ *	If BT_MEM_CTL = WEIM, then
+ *		00 NOR
+ *		01 Reserved
+ *		10 OneNand
+ *		11 Reserved
+ *	If BT_MEM_CTL = NAND Flash
+ *		00 3 address cycles
+ *		01 4 address cycles
+ *		10 5 address cycles
+ *		11 Reserved
+ *	If BT_MEM_CTL = Expansion Card Device
+ *		00 SD/MMC/MoviNAND HDD
+ *		01 Reserved
+ *		10 Serial ROM via I2C
+ *		11 Serial ROM via SPI
+ */
+#define IMX25_IIM_BT_MEM_TYPE		(IIM_BANK(0) | IIM_BYTE(0x14) | IIM_BIT(5) | IIM_WIDTH(2))
+
+/* Bus IIM_WIDTH and muxed/unmuxed interface. Has a corresponding GPIO pin.
+ *	If BT_MEM_CTL=NAND then
+ *		00 8 IIM_BIT bus,
+ *		01 16 IIM_BIT bus
+ *		1x Reserved
+ *	If BT_MEM_CTL=WEIM then
+ *		00 16 IIM_BIT addr/data muxed
+ *		01 16 IIM_BIT addr/data unmuxed
+ *		1x Reserved
+ *	If BT_MEM_CTL=SPI then
+ *		00 2-addr word SPI (16-IIM_BIT)
+ *		01 3-addr word SPI (24-IIM_BIT)
+ *		1x Reserved
+ */
+#define IMX25_IIM_BT_BUS_WIDTH		(IIM_BANK(0) | IIM_BYTE(0x14) | IIM_BIT(3) | IIM_WIDTH(2))
+
+/* Boot Memory Control Type. (memory device)
+ *	00 WEIM
+ *	01 NAND Flash
+ *	10 ATA HDD
+ *	11 Expansion Device
+ *	(SD/MMC, support high storage, EEPROMs. See BT_MEM_TYPE[1:0] settings for details.
+ */
+#define IMX25_IIM_BT_MEM_CTL		(IIM_BANK(0) | IIM_BYTE(0x14) | IIM_BIT(1) | IIM_WIDTH(2))
+
+/* Direct External Memory Boot Disable.
+ *	0 Direct boot from external memory is allowed
+ *	1 Direct boot from external memory is not allowed
+ */
+#define IMX25_IIM_DIR_BT_DIS		(IIM_BANK(0) | IIM_BYTE(0x14) | IIM_BIT(0))
+
+/* HAB Customer Code. Select customer code as input to HAB. */
+#define IMX25_IIM_HAB_CUS		(IIM_BANK(0) | IIM_BYTE(0x18) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Silicon revision number. 0 Rev1.0 1 Rev1.1 */
+#define IMX25_IIM_SI_REV		(IIM_BANK(0) | IIM_BYTE(0x1c) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* 64-IIM_BIT Unique ID. 0 <= n <= 7 */
+#define IMX25_IIM_UID(n)		(IIM_BANK(0) | IIM_BYTE(0x20 + 0x4 * (n)) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* LPB ARM core frequency. Has a corresponding GPIO pin.
+ *	000 133 MHz (Default)
+ *	001 24MHz
+ *	010 55.33 MHz
+ *	011 66 MHz
+ *	100 83 MHz
+ *	101 166 MHz
+ *	110 266 MHz
+ *	111 Normal boot frequency
+ */
+#define IMX25_IIM_BT_LPB_FREQ		(IIM_BANK(0) | IIM_BYTE(0x44) | IIM_BIT(5) | IIM_WIDTH(3))
+
+/* Choosing the specific UART controller for booting from. */
+#define IMX25_IIM_BT_UART_SRC		(IIM_BANK(0) | IIM_BYTE(0x44) | IIM_BIT(2) | IIM_WIDTH(3))
+
+/* Options for Low Power Boot mode.
+ *	00 LPB disabled
+ *	01 Generic PMIC and one GPIO input (Low battery)
+ *	10 Generic PMIC and two GPIO inputs (Low battery and Charger detect)
+ *	11 Atlas AP Power Management IC.
+ */
+#define IMX25_IIM_BT_LPB		(IIM_BANK(0) | IIM_BYTE(0x44) | IIM_BIT(0) | IIM_WIDTH(2))
+
+/* Application Processor Boot Image Version. */
+#define IMX25_IIM_AP_BI_VER_15_8	(IIM_BANK(0) | IIM_BYTE(0x48) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Application Processor Boot Image Version. */
+#define IMX25_IIM_AP_BI_VER_7_0		(IIM_BANK(0) | IIM_BYTE(0x4c) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Most significant IIM_BYTE of 256-IIM_BIT hash value of AP super root key (SRK0_HASH) */
+#define IMX25_IIM_SRK0_HASH_0		(IIM_BANK(0) | IIM_BYTE(0x50) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* For SPC statistics during production. */
+#define IMX25_IIM_STORE_COUNT		(IIM_BANK(0) | IIM_BYTE(0x54) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Use for adjustment the compensator delays on silicon and the system works as a whole at 1.0V and 1.2V (DVFS) */
+#define IMX25_IIM_DVFS_DELAY_ADJUST	(IIM_BANK(0) | IIM_BYTE(0x58) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* PTC version control number. */
+#define IMX25_IIM_PTC_VER		(IIM_BANK(0) | IIM_BYTE(0x5c) | IIM_BIT(5) | IIM_WIDTH(3))
+
+#define IMX25_IIM_GDPTCV_VALID		(IIM_BANK(0) | IIM_BYTE(0x5c) | IIM_BIT(4))
+
+/* GP domain DPTC/SPC Test Voltage. */
+#define IMX25_IIM_GDPTCV		(IIM_BANK(0) | IIM_BYTE(0x5c) | IIM_BIT(0) | IIM_WIDTH(4))
+
+/* Voltage Reference Configuration. A field in DryIce Analog Configuration Register (DACR) */
+#define IMX25_IIM_VRC			(IIM_BANK(0) | IIM_BYTE(0x60) | IIM_BIT(5) | IIM_WIDTH(3))
+
+#define IMX25_IIM_LDPTCV_VALID		(IIM_BANK(0) | IIM_BYTE(0x60) | IIM_BIT(4))
+
+/* LP domain DPTC Test Voltage. */
+#define IMX25_IIM_LDPTCV		(IIM_BANK(0) | IIM_BYTE(0x60) | IIM_BIT(0) | IIM_WIDTH(4))
+
+/* Well Bias Charge Pump Frequency Adjust. Adjusting the frequency of the internal free-running oscillator. */
+#define IMX25_IIM_CPFA			(IIM_BANK(0) | IIM_BYTE(0x64) | IIM_BIT(4))
+
+/* Well Bias Charge Pump Set Point Adjustment. */
+#define IMX25_IIM_CPSPA			(IIM_BANK(0) | IIM_BYTE(0x64) | IIM_BIT(0) | IIM_WIDTH(4))
+
+/* Ethernet MAC Address, 0 <= n <= 5 */
+#define IMX25_IIM_MAC_ADDR(n)		(IIM_BANK(1) | IIM_BYTE(0x68 + 0x4 * (n)) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Locking row 0058, fusebank 1 */
+#define IMX25_IIM_USR5_LOCK		(IIM_BANK(1) | IIM_BYTE(0) | IIM_BIT(4))
+
+/* Lock for rows 0078–007C of fusebank 1 */
+#define IMX25_IIM_USR6_LOCK		(IIM_BANK(1) | IIM_BYTE(0) | IIM_BIT(2))
+
+/* Locking 0008-0020, fusebank1 */
+#define IMX25_IIM_SJC_RESP_LOCK		(IIM_BANK(1) | IIM_BYTE(0) | IIM_BIT(1))
+
+/* Locking SCC_KEY[255:0] */
+#define IMX25_IIM_SCC_LOCK		(IIM_BANK(1) | IIM_BYTE(0) | IIM_BIT(0))
+
+/* SCC Secret Key, 0 <= n <= 20 */
+#define IMX25_IIM_SCC_KEY(n)		(IIM_BANK(1) | IIM_BYTE(0x4 + 0x4 * (n)) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Fuses available for software/customers */
+#define IMX25_IIM_USR5			(IIM_BANK(1) | IIM_BYTE(0x58) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Response reference value for the secure JTAG controller, 0 <= n <= 7 */
+#define IMX25_IIM_SJC_RESP(n)		(IIM_BANK(1) | IIM_BYTE(0x5c + 0x4 * (n)) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Fuses available for software/customers. 0 <= n <= 1 */
+#define IMX25_IIM_USR6(n)		(IIM_BANK(1) | IIM_BYTE(0x78 + 0x4 * (n)) | IIM_BIT(0) | IIM_WIDTH(8))
+
+/* Lock for SRK_HASH[255:160] fuses in row 0x0050, fusebank0 and in rows 0x0004-0x002C, fusebank3 */
+#define IMX25_IIM_SRK0_LOCK96		(IIM_BANK(2) | IIM_BYTE(0) | IIM_BIT(1))
+
+/* Lock for SRK0_HASH[159:0] fuses in rows 0x0030-0x007C */
+#define IMX25_IIM_SRK0_LOCK160		(IIM_BANK(2) | IIM_BYTE(0) | IIM_BIT(0))
+
+/* AP Super Root Key hash, bits [247:0].
+ * Most significant IIM_BYTE SRK_HASH[255:248] is in the fuse bank #0, 0050
+ * 1 <= n <= 31
+ */
+#define IMX25_IIM_SRK0_HASH_1_31(n)	(IIM_BANK(2) | IIM_BYTE(0x4 * (n)) | IIM_BIT(0) | IIM_WIDTH(8))
+
+#endif /* __MACH_IMX25_FUSEMAP_H */
-- 
2.8.0.rc3


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 2/3] ARM: i.MX: IIM: Add function to enable permanent write

[Sascha Hauer]

This adds a function to enable/disable permanent write for the IIM
module so that C users no longer have to fiddle with device parameters.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-imx/iim.c              | 10 ++++++++++
 arch/arm/mach-imx/include/mach/iim.h |  1 +
 2 files changed, 11 insertions(+)

diff --git a/arch/arm/mach-imx/iim.c b/arch/arm/mach-imx/iim.c
index 3aba02f..2e25f69 100644
--- a/arch/arm/mach-imx/iim.c
+++ b/arch/arm/mach-imx/iim.c
@@ -122,6 +122,16 @@ int imx_iim_write_field(uint32_t field, unsigned value)
 	return regmap_write(imx_iim->bank[bank]->map, byte, value);
 }
 
+int imx_iim_permanent_write(int enable)
+{
+	if (!imx_iim)
+		return -ENODEV;
+
+	imx_iim->write_enable = enable;
+
+	return 0;
+}
+
 static int imx_iim_fuse_sense(struct iim_bank *bank, unsigned int row)
 {
 	struct iim_priv *iim = bank->iim;
diff --git a/arch/arm/mach-imx/include/mach/iim.h b/arch/arm/mach-imx/include/mach/iim.h
index f63712e..2161809 100644
--- a/arch/arm/mach-imx/include/mach/iim.h
+++ b/arch/arm/mach-imx/include/mach/iim.h
@@ -99,5 +99,6 @@ static inline int imx25_iim_register_fec_ethaddr(void)
 
 int imx_iim_read_field(uint32_t field, unsigned *value);
 int imx_iim_write_field(uint32_t field, unsigned value);
+int imx_iim_permanent_write(int enable);
 
 #endif /* __MACH_IMX_IIM_H */
-- 
2.8.0.rc3


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

[PATCH 3/3] ARM: i.MX: HABv3: Set to production mode

[Sascha Hauer]

The HABv3 images for engineering mode do not work on a production device
and the images for production mode do not work on an engineering device.

When in engineering mode the ROM checks the images, but does not stop
booting when the signatures are wrong. This means a production image
can still be booted on an engineering device. This device can be
temporarily put into production mode by writing to the HAB_TYPE shadow
fuse register. After a reset the device will come up in production mode
and the image can be tested for validity. This means that if we have to
decide between production mode images and engineering images, the
production images are a better decision. Change this accordingly.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 arch/arm/mach-imx/include/mach/habv3-imx25-gencsf.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-imx/include/mach/habv3-imx25-gencsf.h b/arch/arm/mach-imx/include/mach/habv3-imx25-gencsf.h
index 4b81d49..f4804fe 100644
--- a/arch/arm/mach-imx/include/mach/habv3-imx25-gencsf.h
+++ b/arch/arm/mach-imx/include/mach/habv3-imx25-gencsf.h
@@ -11,7 +11,7 @@ super_root_key CONFIG_HABV3_SRK_PEM
 
 hab [Header]
 hab Version = 3.0
-hab Security Configuration = Engineering
+hab Security Configuration = Production
 hab Hash Algorithm = SHA256
 hab Engine = RTIC
 hab Certificate Format = WTLS
-- 
2.8.0.rc3


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox