[PATCH 18/21] e1000: Properly release SW_FW_SYNC semaphore bits

[Andrey Smirnov <andrew.smirnov@gmail.com>]

As described in the datasheet Software/Firmware synchronisation bits
are expected to be released by the software after it is done using
it. Add a porper subroutine to do that instead of relying on the
Firmware clearing those bits due to timeout.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
---
 drivers/net/e1000/e1000.h |  1 +
 drivers/net/e1000/main.c  | 30 ++++++++++++++++++++++++++++++
 2 files changed, 31 insertions(+)

diff --git a/drivers/net/e1000/e1000.h b/drivers/net/e1000/e1000.h
index 6b7cf82..b47d538 100644
--- a/drivers/net/e1000/e1000.h
+++ b/drivers/net/e1000/e1000.h
@@ -2137,6 +2137,7 @@ int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset,
 		uint16_t *data);
 
 int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
+int32_t e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask);
 
 
 #endif	/* _E1000_HW_H_ */
diff --git a/drivers/net/e1000/main.c b/drivers/net/e1000/main.c
index 7ee78c3..df9ae73 100644
--- a/drivers/net/e1000/main.c
+++ b/drivers/net/e1000/main.c
@@ -273,6 +273,21 @@ int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask)
 	return E1000_SUCCESS;
 }
 
+int32_t e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask)
+{
+	uint32_t swfw_sync;
+
+	if (e1000_get_hw_eeprom_semaphore(hw))
+		return -E1000_ERR_SWFW_SYNC;
+
+	swfw_sync = e1000_read_reg(hw, E1000_SW_FW_SYNC);
+	swfw_sync &= ~mask;
+	e1000_write_reg(hw, E1000_SW_FW_SYNC, swfw_sync);
+
+	e1000_put_hw_eeprom_semaphore(hw);
+	return E1000_SUCCESS;
+}
+
 static bool e1000_is_second_port(struct e1000_hw *hw)
 {
 	switch (hw->mac_type) {
@@ -1347,6 +1362,11 @@ static int32_t e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint
 	e1000_write_reg(hw, E1000_KUMCTRLSTA, reg_val);
 	udelay(2);
 
+	if (e1000_swfw_sync_release(hw, swfw) < 0)
+		dev_warn(hw->dev,
+			 "Timeout while releasing SWFW_SYNC bits (0x%08x)\n",
+			 swfw);
+
 	return E1000_SUCCESS;
 }
 
@@ -1374,6 +1394,11 @@ static int32_t e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint1
 	reg_val = e1000_read_reg(hw, E1000_KUMCTRLSTA);
 	*data = (uint16_t)reg_val;
 
+	if (e1000_swfw_sync_release(hw, swfw) < 0)
+		dev_warn(hw->dev,
+			 "Timeout while releasing SWFW_SYNC bits (0x%08x)\n",
+			 swfw);
+
 	return E1000_SUCCESS;
 }
 
@@ -2803,6 +2828,11 @@ static int32_t e1000_phy_hw_reset(struct e1000_hw *hw)
 
 		if (hw->mac_type >= e1000_82571)
 			mdelay(10);
+
+		if (e1000_swfw_sync_release(hw, swfw) < 0)
+			dev_warn(hw->dev,
+				 "Timeout while releasing SWFW_SYNC bits (0x%08x)\n",
+				 swfw);
 	} else {
 		/* Read the Extended Device Control Register, assert the PHY_RESET_DIR
 		 * bit to put the PHY into reset. Then, take it out of reset.
-- 
2.5.5


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox