From: Andrey Smirnov <andrew.smirnov@gmail.com>
To: barebox@lists.infradead.org
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Subject: [PATCH v2 08/22] e1000: Consolidate register offset fixups
Date: Wed, 1 Jun 2016 21:58:37 -0700 [thread overview]
Message-ID: <1464843531-1824-9-git-send-email-andrew.smirnov@gmail.com> (raw)
In-Reply-To: <1464843531-1824-1-git-send-email-andrew.smirnov@gmail.com>
Consolidate all code taking care on CSR offset differences for i210
chips into a single place in the driver and integrate that funcionality
into e1000_{read,write}_reg functions. This way we can get rid of all
those
if (hw->mac_type == e1000_igb) {
....
} else {
....
}
snippets sprinkled all across the driver code.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
---
drivers/net/e1000/e1000.h | 11 ++++++++---
drivers/net/e1000/eeprom.c | 10 +++-------
drivers/net/e1000/main.c | 17 +++++------------
drivers/net/e1000/regio.c | 25 +++++++++++++++++++++++++
4 files changed, 41 insertions(+), 22 deletions(-)
diff --git a/drivers/net/e1000/e1000.h b/drivers/net/e1000/e1000.h
index d75c707..1d0b3c6 100644
--- a/drivers/net/e1000/e1000.h
+++ b/drivers/net/e1000/e1000.h
@@ -389,6 +389,11 @@ struct e1000_tx_desc {
#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */
#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
+#define E1000_MIGHT_BE_REMAPPED 0x80000000 /* Flag indicating that on
+ some variants of the chip
+ register offset might be
+ different */
+
/* Register Set. (82543, 82544)
*
* Registers are defined to be 32 bits and should be accessed as 32 bit values.
@@ -429,17 +434,17 @@ struct e1000_tx_desc {
#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
-#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */
+#define E1000_PHY_CTRL (E1000_MIGHT_BE_REMAPPED | 0x00F10) /* PHY Control Register in CSR */
#define E1000_I210_PHY_CTRL 0x00E14 /* PHY Control Register in CSR */
#define FEXTNVM_SW_CONFIG 0x0001
#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
#define E1000_PBS 0x01008 /* Packet Buffer Size */
-#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
+#define E1000_EEMNGCTL (E1000_MIGHT_BE_REMAPPED | 0x01010) /* MNG EEprom Control */
#define E1000_I210_EEMNGCTL 0x12030 /* MNG EEprom Control */
#define E1000_FLASH_UPDATES 1000
#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */
#define E1000_FLASHT 0x01028 /* FLASH Timer Register */
-#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
+#define E1000_EEWR (E1000_MIGHT_BE_REMAPPED | 0x0102C) /* EEPROM Write Register - RW */
#define E1000_I210_EEWR 0x12018 /* EEPROM Write Register - RW */
#define E1000_FLSWCTL 0x01030 /* FLASH control register */
#define E1000_FLSWDATA 0x01034 /* FLASH data register */
diff --git a/drivers/net/e1000/eeprom.c b/drivers/net/e1000/eeprom.c
index 497fb7b..c2dfad5 100644
--- a/drivers/net/e1000/eeprom.c
+++ b/drivers/net/e1000/eeprom.c
@@ -451,14 +451,10 @@ static int32_t e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
int32_t done = E1000_ERR_EEPROM;
for (i = 0; i < attempts; i++) {
- if (eerd == E1000_EEPROM_POLL_READ) {
+ if (eerd == E1000_EEPROM_POLL_READ)
reg = e1000_read_reg(hw, E1000_EERD);
- } else {
- if (hw->mac_type == e1000_igb)
- reg = e1000_read_reg(hw, E1000_I210_EEWR);
- else
- reg = e1000_read_reg(hw, E1000_EEWR);
- }
+ else
+ reg = e1000_read_reg(hw, E1000_EEWR);
if (reg & E1000_EEPROM_RW_REG_DONE) {
done = E1000_SUCCESS;
diff --git a/drivers/net/e1000/main.c b/drivers/net/e1000/main.c
index f1055ea..4a527a3 100644
--- a/drivers/net/e1000/main.c
+++ b/drivers/net/e1000/main.c
@@ -1184,14 +1184,11 @@ static int32_t e1000_set_d0_lplu_state_off(struct e1000_hw *hw)
if (hw->mac_type <= e1000_82547_rev_2)
return E1000_SUCCESS;
- if (hw->mac_type == e1000_ich8lan) {
+ if (hw->mac_type == e1000_ich8lan ||
+ hw->mac_type == e1000_igb) {
phy_ctrl = e1000_read_reg(hw, E1000_PHY_CTRL);
phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
e1000_write_reg(hw, E1000_PHY_CTRL, phy_ctrl);
- } else if (hw->mac_type == e1000_igb) {
- phy_ctrl = e1000_read_reg(hw, E1000_I210_PHY_CTRL);
- phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
- e1000_write_reg(hw, E1000_I210_PHY_CTRL, phy_ctrl);
} else {
ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
&phy_data);
@@ -2745,13 +2742,9 @@ static int32_t e1000_get_phy_cfg_done(struct e1000_hw *hw)
case e1000_82572:
case e1000_igb:
while (timeout) {
- if (hw->mac_type == e1000_igb) {
- if (e1000_read_reg(hw, E1000_I210_EEMNGCTL) & cfg_mask)
- break;
- } else {
- if (e1000_read_reg(hw, E1000_EEMNGCTL) & cfg_mask)
- break;
- }
+ if (e1000_read_reg(hw, E1000_EEMNGCTL) & cfg_mask)
+ break;
+
mdelay(1);
timeout--;
}
diff --git a/drivers/net/e1000/regio.c b/drivers/net/e1000/regio.c
index 8c529f1..4970084 100644
--- a/drivers/net/e1000/regio.c
+++ b/drivers/net/e1000/regio.c
@@ -2,13 +2,38 @@
#include "e1000.h"
+static uint32_t e1000_true_offset(struct e1000_hw *hw, uint32_t reg)
+{
+ if (reg & E1000_MIGHT_BE_REMAPPED) {
+ reg &= ~E1000_MIGHT_BE_REMAPPED;
+
+ if (hw->mac_type == e1000_igb) {
+ switch (reg) {
+ case E1000_EEWR:
+ reg = E1000_I210_EEWR;
+ break;
+ case E1000_PHY_CTRL:
+ reg = E1000_I210_PHY_CTRL;
+ break;
+ case E1000_EEMNGCTL:
+ reg = E1000_I210_EEMNGCTL;
+ break;
+ }
+ };
+ }
+
+ return reg;
+}
+
void e1000_write_reg(struct e1000_hw *hw, uint32_t reg, uint32_t value)
{
+ reg = e1000_true_offset(hw, reg);
writel(value, hw->hw_addr + reg);
}
uint32_t e1000_read_reg(struct e1000_hw *hw, uint32_t reg)
{
+ reg = e1000_true_offset(hw, reg);
return readl(hw->hw_addr + reg);
}
--
2.5.5
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2016-06-02 4:59 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-02 4:58 [PATCH v2 00/22] e1000 code cleanup and iNVM support Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 01/22] e1000: Split driver into multiple files Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 02/22] e1000: Include <net.h> in e1000.h Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 03/22] e1000: Convert E1000_*_REG macros to functions Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 04/22] e1000: Fix a bug in e1000_detect_gig_phy Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 05/22] e1000: Remove unnecessary variable Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 06/22] e1000: Do not read same register twice Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 07/22] e1000: Remove unneeded i210 specific register code Andrey Smirnov
2016-06-02 4:58 ` Andrey Smirnov [this message]
2016-06-02 4:58 ` [PATCH v2 09/22] e1000: Remove 'use_eewr' parameter Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 10/22] e1000: Remove 'page_size' Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 11/22] e1000: Simplify EEPROM init for e1000_80003es2lan Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 12/22] e1000: Simplify EEPROM init for e1000_igb Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 13/22] e1000: Consolidate SPI EEPROM init code Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 14/22] e1000: Consolidate Microwire " Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 15/22] e1000: Fix a bug in e1000_probe() Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 16/22] e1000: Remove unnecessary intialization Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 17/22] e1000: Refactor Flash/EEPROM reading code Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 18/22] e1000: Properly release SW_FW_SYNC semaphore bits Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 19/22] e1000: Add EEPROM access locking for i210 Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 20/22] e1000: Add a "poll register" function Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 21/22] e1000: Expose i210's iNVM as a cdev Andrey Smirnov
2016-06-02 4:58 ` [PATCH v2 22/22] e1000: Expose i210's external flash as MTD Andrey Smirnov
2016-06-03 7:15 ` [PATCH v2 00/22] e1000 code cleanup and iNVM support Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1464843531-1824-9-git-send-email-andrew.smirnov@gmail.com \
--to=andrew.smirnov@gmail.com \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox