mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: "Jan Lübbe" <jlu@pengutronix.de>
To: Sascha Hauer <s.hauer@pengutronix.de>,
	Patrick Huesmann <patrick.huesmann@gmail.com>
Cc: barebox@lists.infradead.org, Enrico Joerns <ejo@pengutronix.de>
Subject: Re: bootchooser: constant decrement of remaining_attempts
Date: Wed, 10 Oct 2018 10:06:57 +0200	[thread overview]
Message-ID: <1539158817.19112.52.camel@pengutronix.de> (raw)
In-Reply-To: <20181010071443.msez5a7yriayx2va@pengutronix.de>

On Wed, 2018-10-10 at 09:14 +0200, Sascha Hauer wrote:
> Hi Patrick,
> 
> +Cc Jan and Enrico
> 
> On Tue, Oct 09, 2018 at 06:37:25PM +0200, Patrick Huesmann wrote:
> > Hi,
> > 
> > I'm building a RAUC- & bootchooser-based firmware update solution.
> > The scenario is symmetric rootfs slots, manual update, userspace
> > (RAUC) marks as good.
> > It seems to work well, however I noticed that it's always decrementing
> > and resetting the remaining_attempts of the booted system, not only
> > when there's an update, but also during regular boot-ups.
> > 
> > I thought that the RAUC/bootchooser combo was mainly about providing a
> > safeguard against accidentally "bricking" the system with corrupt or
> > incomplete firmware updates.
> > However, the logic of decrementing and later resetting the
> > remaining_attempts is apparently not limited to the period between
> > performing the update and the validation (mark as good) of that
> > update, but also running all the other times the system is booted.
> > 
> > This can have some undesirable side effects:
> > 
> > 1) When the boot process is interrupted for any reason (power issues,
> > brown-out resets, users unplugging the gadget while it boots, etc.)
> > more than three times in a row (assuming a remaining_attempts reset
> > value of 3), then bootchooser will happily switch to the fall-back
> > target, even though there's nothing wrong with the actual target at
> > all.
> 
> I think what you want here is the global.bootchooser.reset_attempts=power-on
> option. With this option bootchooser will reset the remaining attempts
> to the default value with each power on reset, meaning that the primary
> target will only become invalid when the watchdog bites you three times
> in a row, but not when the device is turned off in between.

If you want to ensure that the old system is not booted anymore, you
should set its priority to zero.

Leaving the old image enabled is useful in cases where you want to
protect against problems that occur some time after the update.

> > I guess this can be worked around by syncing the fall-back target to
> > the last updated one, after the last update has been verified as good.
> > However this brings additional cost & complexity, and feels more like
> > a hack than a proper solution.
> > 
> > 2) In every complete boot cycle, there are two writes to the
> > barebox-state partition (bootchooser decrementing the
> > remaining_attempts, then userspace resetting the remaining_attempts
> > when it marks the target as good). For systems that boot up & power
> > down a lot, this will generate lots of unnecessary flash writes over
> > time. Probably it won't be enough to actually wear out the flash, but
> > still it doesn't "feel" quite right. (I jumped through hoops to have a
> > proper read-only root and would like to limit the overall number of
> > flash writes when possible).
> > 
> > I'm thinking of an option that limits the remaining_attempts logic to
> > the phase when barebox attempts to boot a newly flashed update, until
> > that update is marked as good later in userspace. There could be an
> > extra (optional) variable in the barebox-state, that allows the
> > userspace to deliberately enable/disable the remaining_attempts logic
> > in barebox.
> 
> I don't think such an option is available at the moment. Maybe we could
> declare remaining_attempts=INT_MAX as infinite attempts. Whenever that
> value is found the remaining_attempts counter wouldn't be decreased.
> 
> After an update userspace could then set the remaining_attempts counter
> of the new system to three and the new system would set it to INT_MAX
> when successfully booted.

INT_MAX would need to be relative to the actual type defined in the
state variable (u32 vs. u8). An alternative would be to have a global
flag to en-/disable counting.

Currently there is one way to avoid writes to flash in the successful
case: Use a watchdog and call bootchooser -s, which will cause it to
skip decrementing if it boots the same target as previously. It seems
that's not documented, though. :/

Regards,
Jan
-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  reply	other threads:[~2018-10-10  8:07 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-10-09 16:37 Patrick Huesmann
2018-10-10  7:14 ` Sascha Hauer
2018-10-10  8:06   ` Jan Lübbe [this message]
2018-10-10 11:40     ` Patrick Huesmann
2018-10-11  8:25       ` Patrick Huesmann

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1539158817.19112.52.camel@pengutronix.de \
    --to=jlu@pengutronix.de \
    --cc=barebox@lists.infradead.org \
    --cc=ejo@pengutronix.de \
    --cc=patrick.huesmann@gmail.com \
    --cc=s.hauer@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox