From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from metis.ext.pengutronix.de ([2001:6f8:1178:4:290:27ff:fe1d:cc33]) by canuck.infradead.org with esmtps (Exim 4.72 #1 (Red Hat Linux)) id 1Ptxiy-0007FV-Rt for barebox@lists.infradead.org; Mon, 28 Feb 2011 07:40:58 +0000 Date: Mon, 28 Feb 2011 08:40:53 +0100 From: Sascha Hauer Message-ID: <20110228074053.GF29521@pengutronix.de> References: <4D665867.4010404@telemotive.de> <20110224160440.GQ7381@pengutronix.de> <4D677315.5090600@telemotive.de> <20110225150657.GC29521@pengutronix.de> <4D67D3EA.9000106@telemotive.de> MIME-Version: 1.0 Content-Disposition: inline In-Reply-To: <4D67D3EA.9000106@telemotive.de> List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: barebox-bounces@lists.infradead.org Errors-To: barebox-bounces+u.kleine-koenig=pengutronix.de@lists.infradead.org Subject: Re: Install barebox on target To: Thomas Mayer Cc: barebox@lists.infradead.org On Fri, Feb 25, 2011 at 05:08:10PM +0100, Thomas Mayer wrote: > Hi Sasha, > > thanks, I will try that. > Today I got our real hardware. It consists of the freescale cpu board, a > custom baseboard with a different display. > With that I was able to start barebox completely. Network works fine, > but I can't access the nand memory, because barebox doesn't find it at > startup. I added all possible nand drivers to barebox, but it still > doesn't work. > > Any idea? > > --------------------------------------- u-boot output > ----------------------------------------- > U-Boot 2009.08 (Jan 13 2010 - > > Page Geometry : > 4096+218 This will cause problems. I never had a nand with 4k block size and I doubt it will work out of the box. I don't know if that's the reason barebox does not find no nand device at all though. Sasha > > --------------------------------------- barebox output > ------------------------------------------ > barebox 2011.02.0 (Feb 25 2011 - 16:35:47) > > Board: Freescale MX35 3Stack > No NAND device found!!! > cfi_probe: cfi_flash base: 0xa0000000 size: 0x04000000 > mc13892-i2c@mc13892-i2c0: PMIC ID: 0x000045d0 [Rev: 2.0a] > smc911x: no smc911x found on 0xb6000000 (byte_test=0x00f000f0) > imx-ipu-fb@imx-ipu-fb0: i.MX Framebuffer driver > mc13892-i2c@mc13892-i2c0: revision: 0x45d0 > i.MX35 PDK CPU board version 1. > Malloc space: 0x86f00000 -> 0x87f00000 (size 16 MB) > Stack space : 0x86ef8000 -> 0x86f00000 (size 32 kB) > Open /dev/env0 No such file or directory > no valid environment found on /dev/env0. Using default environment > running /env/bin/init... > > > > regards > Thomas > > > > Am 25.02.2011 16:06, schrieb Sascha Hauer: > > On Fri, Feb 25, 2011 at 10:15:01AM +0100, Thomas Mayer wrote: > > > >> Hi Sascha, > >> > >> That's not quite correct. When you use the debug + personality board you > >> can boot directly from a mmc-card which contains bootloader, kernel and > >> rootfs without modifications. Only if you use the single personality > >> board, you have to modify die board a little bit. > >> > > Ah, ok. I didn't know that. > > > > > >> Thanks for your short introduction. I tried to run the barebox image > >> with u-boot and it seems to work. But after I get the following output > >> barebox stops and do nothing. > >> > > That's a bug in the support for multiple network devices. Please pull > > the -next branch again, then it should work. > > > > Sascha > > > > > > > > > _______________________________________________ > barebox mailing list > barebox@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/barebox > -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox