* barebox on gta04
@ 2011-10-24 21:01 Johannes Schauer
2011-10-24 21:07 ` Robert Schwebel
0 siblings, 1 reply; 10+ messages in thread
From: Johannes Schauer @ 2011-10-24 21:01 UTC (permalink / raw)
To: barebox; +Cc: gta04-owner
Hi,
I was booting barebox from git on my "openmoko" gta04 today but what was
not working was the mmc initialization.
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: barebox on gta04
2011-10-24 21:01 barebox on gta04 Johannes Schauer
@ 2011-10-24 21:07 ` Robert Schwebel
0 siblings, 0 replies; 10+ messages in thread
From: Robert Schwebel @ 2011-10-24 21:07 UTC (permalink / raw)
To: Johannes Schauer; +Cc: barebox
On Mon, Oct 24, 2011 at 11:01:52PM +0200, Johannes Schauer wrote:
> I was booting barebox from git on my "openmoko" gta04 today but what was
> not working was the mmc initialization.
Can you send us more information about *what* goes wrong? Do you see
something in the kernel output? Any error messages? Please provide your
boot lot.
rsc
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* barebox on gta04
@ 2011-10-24 21:11 Johannes Schauer
2011-10-24 21:34 ` Sascha Hauer
0 siblings, 1 reply; 10+ messages in thread
From: Johannes Schauer @ 2011-10-24 21:11 UTC (permalink / raw)
To: barebox; +Cc: gta04-owner
Hi,
I was booting barebox from git on my "openmoko" gta04 today but what was
not working was the mmc initialization.
It was failing in mmc_init_setup() in ./drivers/mci/omap_hsmmc.c after
printing "timedout waiting for cc2!" when I had DEBUG enabled.
-%<-----------------------------------------------------------------
barebox 2011.10.0-00107-gdac6e90-dirty (Oct 24 2011 - 22:12:10)
Board: Texas Instrument's Beagle
omap-hsmmc@omap-hsmmc0: timedout waiting for cc2!
Cannot reset the SD/MMC interface
->%-----------------------------------------------------------------
The gta04 should be very similar to the beagleboard and hence I was
building using the omap3530_beagle_defconfig.
any hints on how to continue debugging this problem are highly
appreciated!
cheers, josch
PS: sorry for my previous mail which was the result of hitting "y"
instead of "e" in my mutt...
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: barebox on gta04
2011-10-24 21:11 Johannes Schauer
@ 2011-10-24 21:34 ` Sascha Hauer
2011-10-25 6:38 ` Johannes Schauer
0 siblings, 1 reply; 10+ messages in thread
From: Sascha Hauer @ 2011-10-24 21:34 UTC (permalink / raw)
To: 20111024202514.GA17005; +Cc: gta04-owner, barebox
Hi Johannes,
On Mon, Oct 24, 2011 at 11:11:37PM +0200, Johannes Schauer wrote:
> Hi,
>
>
> I was booting barebox from git on my "openmoko" gta04 today but what was
> not working was the mmc initialization.
>
> It was failing in mmc_init_setup() in ./drivers/mci/omap_hsmmc.c after
> printing "timedout waiting for cc2!" when I had DEBUG enabled.
>
> -%<-----------------------------------------------------------------
> barebox 2011.10.0-00107-gdac6e90-dirty (Oct 24 2011 - 22:12:10)
>
> Board: Texas Instrument's Beagle
> omap-hsmmc@omap-hsmmc0: timedout waiting for cc2!
> Cannot reset the SD/MMC interface
> ->%-----------------------------------------------------------------
>
> The gta04 should be very similar to the beagleboard and hence I was
> building using the omap3530_beagle_defconfig.
>
> any hints on how to continue debugging this problem are highly
> appreciated!
You could start barebox from U-Boot (just load the barebox binary image
to RAM and jump to it using the U-Boot 'go' command). Then you could
comment out the lowlevel code from barebox (arch_init_lowlevel, pin_mux)
and see if the problem persists. Maybe there is something different in
the lowlevel code.
Another thing: Where does this string come from? We have this twice in
the driver and one of them should really be "timeout waiting for reset
done"
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: barebox on gta04
2011-10-24 21:34 ` Sascha Hauer
@ 2011-10-25 6:38 ` Johannes Schauer
2011-10-25 8:36 ` Sascha Hauer
0 siblings, 1 reply; 10+ messages in thread
From: Johannes Schauer @ 2011-10-25 6:38 UTC (permalink / raw)
To: barebox; +Cc: gta04-owner
Hi Sascha,
On Mon, Oct 24, 2011 at 11:34:13PM +0200, Sascha Hauer wrote:
> You could start barebox from U-Boot (just load the barebox binary
> image to RAM and jump to it using the U-Boot 'go' command). Then you
> could comment out the lowlevel code from barebox (arch_init_lowlevel,
> pin_mux) and see if the problem persists. Maybe there is something
> different in the lowlevel code.
This is a great idea! So first I loaded the unmodified barebox binary
using:
mmc rescan 0
fatload mmc 0 0x82000000 barebox.bin
go 0x82000000
It started executing and the error was the same as before.
Then I tried doing what you suggested above and commented
arch_init_lowlevel in ./arch/arm/mach-omap/omap3_core.S and I was not
sure what you meant by `pin_mux` as the string appeared nowhere in the
code but I thought you might mean the mux_config in
./arch/arm/boards/omap/board-beagle.c ? But after doing that, barebox
would just not start anymore when loaded by uboot.
So can you give me some more specific advices on what to comment?
> Another thing: Where does this string come from? We have this twice in
> the driver and one of them should really be "timeout waiting for reset
> done"
If I read the code correctly, then my error comes from line
224 of ./drivers/mci/omap_hsmmc.c :
dev_dbg(hsmmc->dev, "timedout waiting for cc2!\n");
I activated this debug message by using "#define DEBUG" on top of the
file. Initially I only got the message "Cannot reset the SD/MMC
interface" from line 1185 in ./drivers/mci/mci-core.c after it tried to
call the init code from omap_hsmmc.c.
But where would you find "timeout waiting for reset done"? I tried to
recursively grep my barebox sources without finding this string?
thanks!
cheers, josch
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: barebox on gta04
2011-10-25 6:38 ` Johannes Schauer
@ 2011-10-25 8:36 ` Sascha Hauer
2011-10-25 10:05 ` Johannes Schauer
0 siblings, 1 reply; 10+ messages in thread
From: Sascha Hauer @ 2011-10-25 8:36 UTC (permalink / raw)
To: Johannes Schauer; +Cc: gta04-owner, barebox
On Tue, Oct 25, 2011 at 08:38:50AM +0200, Johannes Schauer wrote:
> Hi Sascha,
>
> On Mon, Oct 24, 2011 at 11:34:13PM +0200, Sascha Hauer wrote:
> > You could start barebox from U-Boot (just load the barebox binary
> > image to RAM and jump to it using the U-Boot 'go' command). Then you
> > could comment out the lowlevel code from barebox (arch_init_lowlevel,
> > pin_mux) and see if the problem persists. Maybe there is something
> > different in the lowlevel code.
>
> This is a great idea! So first I loaded the unmodified barebox binary
> using:
>
> mmc rescan 0
> fatload mmc 0 0x82000000 barebox.bin
> go 0x82000000
>
> It started executing and the error was the same as before.
>
> Then I tried doing what you suggested above and commented
> arch_init_lowlevel in ./arch/arm/mach-omap/omap3_core.S and I was not
> sure what you meant by `pin_mux` as the string appeared nowhere in the
> code but I thought you might mean the mux_config in
> ./arch/arm/boards/omap/board-beagle.c ?
Yes, that's what I meant
> But after doing that, barebox
> would just not start anymore when loaded by uboot.
Strange. Should not be the case, no idea what's happening here.
>
> So can you give me some more specific advices on what to comment?
>
> > Another thing: Where does this string come from? We have this twice in
> > the driver and one of them should really be "timeout waiting for reset
> > done"
>
> If I read the code correctly, then my error comes from line
> 224 of ./drivers/mci/omap_hsmmc.c :
>
> dev_dbg(hsmmc->dev, "timedout waiting for cc2!\n");
Look again, we accidently have the same string twice in the driver:
./drivers/mci/omap_hsmmc.c:201: dev_dbg(hsmmc->dev, "timedout waiting for cc2!\n");
./drivers/mci/omap_hsmmc.c:224: dev_dbg(hsmmc->dev, "timedout waiting for cc2!\n");
The one in line 224 should really be "timeout waiting for reset done".
So what I wanted to know is whether it's the error message in line 201
or 224 that we see. So please change one of them
>
> I activated this debug message by using "#define DEBUG" on top of the
> file. Initially I only got the message "Cannot reset the SD/MMC
> interface" from line 1185 in ./drivers/mci/mci-core.c after it tried to
> call the init code from omap_hsmmc.c.
>
> But where would you find "timeout waiting for reset done"? I tried to
> recursively grep my barebox sources without finding this string?
>
> thanks!
>
> cheers, josch
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: barebox on gta04
2011-10-25 8:36 ` Sascha Hauer
@ 2011-10-25 10:05 ` Johannes Schauer
2011-10-31 11:57 ` Robert Schwebel
0 siblings, 1 reply; 10+ messages in thread
From: Johannes Schauer @ 2011-10-25 10:05 UTC (permalink / raw)
To: Sascha Hauer; +Cc: gta04-owner, barebox
Hi,
On Tue, Oct 25, 2011 at 10:36:47AM +0200, Sascha Hauer wrote:
> > But after doing that, barebox would just not start anymore when
> > loaded by uboot.
>
> Strange. Should not be the case, no idea what's happening here.
any ideas on what I can try?
> Look again, we accidently have the same string twice in the driver:
>
> ./drivers/mci/omap_hsmmc.c:201: dev_dbg(hsmmc->dev, "timedout waiting for cc2!\n");
> ./drivers/mci/omap_hsmmc.c:224: dev_dbg(hsmmc->dev, "timedout waiting for cc2!\n");
>
> The one in line 224 should really be "timeout waiting for reset done".
>
> So what I wanted to know is whether it's the error message in line 201
> or 224 that we see. So please change one of them
I changed both, appending the string of the function calling them
(mmc_init_stream and mmc_init_setup)
when booting I get:
barebox 2011.10.0-00107-gdac6e90-dirty (Oct 25 2011 - 12:00:54)
Board: Texas Instrument's Beagle
omap-hsmmc@omap-hsmmc0: timedout waiting for cc2! (in mmc_init_setup)
Cannot reset the SD/MMC interface
So this is where it comes from.
cheers, josch
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: barebox on gta04
2011-10-25 10:05 ` Johannes Schauer
@ 2011-10-31 11:57 ` Robert Schwebel
2011-10-31 14:05 ` Johannes Schauer
0 siblings, 1 reply; 10+ messages in thread
From: Robert Schwebel @ 2011-10-31 11:57 UTC (permalink / raw)
To: Johannes Schauer; +Cc: gta04-owner, barebox
Hi Johannes,
On Tue, Oct 25, 2011 at 12:05:35PM +0200, Johannes Schauer wrote:
> > Strange. Should not be the case, no idea what's happening here.
>
> any ideas on what I can try?
Does barebox now work on your gtk04? If not, I'd be willing to help with
the port, but somebody would have to organze a hardware for us in that
case.
rsc
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: barebox on gta04
2011-10-31 11:57 ` Robert Schwebel
@ 2011-10-31 14:05 ` Johannes Schauer
2011-10-31 14:18 ` Robert Schwebel
0 siblings, 1 reply; 10+ messages in thread
From: Johannes Schauer @ 2011-10-31 14:05 UTC (permalink / raw)
To: Robert Schwebel; +Cc: gta04-owner, barebox
Hi,
On Mon, Oct 31, 2011 at 12:57:48PM +0100, Robert Schwebel wrote:
> Does barebox now work on your gtk04?
nope, I'm relying on input from you guys ;)
> If not, I'd be willing to help with the port, but somebody would have
> to organze a hardware for us in that case.
if there are no leftover units in munich and you are located in germany
i could lend you mine for one or two weeks?
cheers, josch
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: barebox on gta04
2011-10-31 14:05 ` Johannes Schauer
@ 2011-10-31 14:18 ` Robert Schwebel
0 siblings, 0 replies; 10+ messages in thread
From: Robert Schwebel @ 2011-10-31 14:18 UTC (permalink / raw)
To: Johannes Schauer; +Cc: gta04-owner, barebox
On Mon, Oct 31, 2011 at 03:05:39PM +0100, Johannes Schauer wrote:
> On Mon, Oct 31, 2011 at 12:57:48PM +0100, Robert Schwebel wrote:
> > Does barebox now work on your gtk04?
>
> nope, I'm relying on input from you guys ;)
>
> > If not, I'd be willing to help with the port, but somebody would
> > have to organze a hardware for us in that case.
>
> if there are no leftover units in munich and you are located in
> germany i could lend you mine for one or two weeks?
We are located in Germany (see signature). However, the variant with the
leftover units would be preferred :-)
rsc
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2011-10-31 14:18 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2011-10-24 21:01 barebox on gta04 Johannes Schauer
2011-10-24 21:07 ` Robert Schwebel
2011-10-24 21:11 Johannes Schauer
2011-10-24 21:34 ` Sascha Hauer
2011-10-25 6:38 ` Johannes Schauer
2011-10-25 8:36 ` Sascha Hauer
2011-10-25 10:05 ` Johannes Schauer
2011-10-31 11:57 ` Robert Schwebel
2011-10-31 14:05 ` Johannes Schauer
2011-10-31 14:18 ` Robert Schwebel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox