mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
To: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: barebox@lists.infradead.org
Subject: Re: *** PROBABLY SPAM *** [PATCH v2 6/7] platform: add support for aizo dSS11
Date: Fri, 9 Dec 2011 16:01:31 +0100	[thread overview]
Message-ID: <20111209150131.GP23884@game.jcrosoft.org> (raw)
In-Reply-To: <20111209112900.GH8203@pengutronix.de>

On 12:29 Fri 09 Dec     , Michael Grzeschik wrote:
> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
> ---
>  arch/arm/Makefile                |    1 +
>  arch/arm/boards/dss11/Makefile   |    1 +
>  arch/arm/boards/dss11/config.h   |    6 ++
>  arch/arm/boards/dss11/env/config |   42 ++++++++++
>  arch/arm/boards/dss11/init.c     |  156 ++++++++++++++++++++++++++++++++++++++
>  arch/arm/mach-at91/Kconfig       |    8 ++
>  6 files changed, 214 insertions(+), 0 deletions(-)
>  create mode 100644 arch/arm/boards/dss11/Makefile
>  create mode 100644 arch/arm/boards/dss11/config.h
>  create mode 100644 arch/arm/boards/dss11/env/config
>  create mode 100644 arch/arm/boards/dss11/init.c
> 
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index 6f5f343..e5e951c 100644
>  - removed GPL address
>  - increased barebox and env partition size
>  - changed boot partition on nand
>  - removed lowlevel.S
>  - fixed nand bus_width to 16
>  - moved ethernet pin handling to another patch
>  - touch mach-types from another patch
>  - removed kernel and rootfs partitions
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -66,6 +66,7 @@ board-$(CONFIG_MACH_AT91SAM9263EK)		:= at91sam9263ek
>  board-$(CONFIG_MACH_AT91SAM9G10EK)		:= at91sam9261ek
>  board-$(CONFIG_MACH_AT91SAM9G20EK)		:= at91sam9260ek
>  board-$(CONFIG_MACH_AT91SAM9M10G45EK)		:= at91sam9m10g45ek
> +board-$(CONFIG_MACH_DSS11)			:= dss11
>  board-$(CONFIG_MACH_EDB9301)			:= edb93xx
>  board-$(CONFIG_MACH_EDB9302)			:= edb93xx
>  board-$(CONFIG_MACH_EDB9302A)			:= edb93xx
> diff --git a/arch/arm/boards/dss11/Makefile b/arch/arm/boards/dss11/Makefile
> new file mode 100644
> index 0000000..eb072c0
> --- /dev/null
> +++ b/arch/arm/boards/dss11/Makefile
> @@ -0,0 +1 @@
> +obj-y += init.o
> diff --git a/arch/arm/boards/dss11/config.h b/arch/arm/boards/dss11/config.h
> new file mode 100644
> index 0000000..006820c
> --- /dev/null
> +++ b/arch/arm/boards/dss11/config.h
> @@ -0,0 +1,6 @@
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define AT91_MAIN_CLOCK		18432000	/* 18.432 MHz crystal */
> +
> +#endif	/* __CONFIG_H */
> diff --git a/arch/arm/boards/dss11/env/config b/arch/arm/boards/dss11/env/config
> new file mode 100644
> index 0000000..5c9be7d
> --- /dev/null
> +++ b/arch/arm/boards/dss11/env/config
> @@ -0,0 +1,42 @@
> +#!/bin/sh
> +
> +# use 'dhcp' to do dhcp in barebox and in kernel
> +# use 'none' if you want to skip kernel ip autoconfiguration
> +ip=dhcp
> +
> +# or set your networking parameters here
> +#eth0.ipaddr=a.b.c.d
> +#eth0.netmask=a.b.c.d
> +#eth0.gateway=a.b.c.d
> +#eth0.serverip=a.b.c.d
> +
> +# can be either 'nfs', 'tftp' or 'nand'
> +kernel_loc=tftp
> +# can be either 'net', 'nand' or 'initrd'
> +rootfs_loc=net
> +
> +# can be either 'jffs2' or 'ubifs'
> +rootfs_type=ubifs
> +rootfsimage=root.$rootfs_type
> +
> +# The image type of the kernel. Can be uimage, zimage, raw, or raw_lzo
> +#kernelimage_type=zimage
> +#kernelimage=zImage
> +kernelimage_type=uimage
> +kernelimage=uImage
> +#kernelimage_type=raw
> +#kernelimage=Image
> +#kernelimage_type=raw_lzo
> +#kernelimage=Image.lzo
> +
> +nand_device=atmel_nand
> +nand_parts="128k(bootstrap),512k(barebox)ro,512k(barebox-env),2M(kernel-rescue),2M(kernel-prod),32M(rootfs-rescue),200M(rootfs-prod),-(config)"
> +rootfs_mtdblock_nand=4
> +
> +autoboot_timeout=3
> +
> +bootargs="console=ttyS0,115200"
> +
> +# set a fancy prompt (if support is compiled in)
> +PS1="\e[1;32mbarebox@\e[1;31m\h:\w\e[0m "
> +
> diff --git a/arch/arm/boards/dss11/init.c b/arch/arm/boards/dss11/init.c
> new file mode 100644
> index 0000000..96c4eef
> --- /dev/null
> +++ b/arch/arm/boards/dss11/init.c
> @@ -0,0 +1,156 @@
> +/*
> + * Copyright (C) 2011 Michael Grzeschik <mgr@pengutronix.de>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <common.h>
> +#include <net.h>
> +#include <mci.h>
> +#include <init.h>
> +#include <environment.h>
> +#include <fec.h>
> +#include <asm/armlinux.h>
> +#include <generated/mach-types.h>
> +#include <partition.h>
> +#include <fs.h>
> +#include <fcntl.h>
> +#include <asm/io.h>
> +#include <asm/hardware.h>
> +#include <nand.h>
> +#include <linux/mtd/nand.h>
> +#include <mach/board.h>
> +#include <mach/at91sam9_smc.h>
> +#include <mach/sam9_smc.h>
> +#include <gpio.h>
> +#include <mach/io.h>
> +#include <mach/at91_pmc.h>
> +#include <mach/at91_rstc.h>
> +
> +static struct atmel_nand_data nand_pdata = {
> +	.ale		= 21,
> +	.cle		= 22,
> +/*	.det_pin	= ... not connected */
please use -EINVAL

I'm going to apply the same cleanup on barebox that I did on the kernel
> +	.ecc_mode	= NAND_ECC_HW,

this will not work IIRC
the current implementation is bugged
I've to fix it in the kernel at least
> +	.rdy_pin	= AT91_PIN_PC13,
> +	.enable_pin	= AT91_PIN_PC14,
> +	.bus_width_16	= 1,
> +};
> +
> +static struct sam9_smc_config dss11_nand_smc_config = {
> +	.ncs_read_setup		= 0,
> +	.nrd_setup		= 1,
> +	.ncs_write_setup	= 0,
> +	.nwe_setup		= 1,
> +
> +	.ncs_read_pulse		= 3,
> +	.nrd_pulse		= 3,
> +	.ncs_write_pulse	= 3,
> +	.nwe_pulse		= 3,
> +
> +	.read_cycle		= 5,
> +	.write_cycle		= 5,
> +
> +	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
> +	.tdf_cycles		= 2,
> +};
> +
> +static void dss11_add_device_nand(void)
> +{
> +	/* setup bus-width (16) */
> +	dss11_nand_smc_config.mode |= AT91_SMC_DBW_16;
put it directly in the struct to reduce the size
> +
> +	/* configure chip-select 3 (NAND) */
> +	sam9_smc_configure(3, &dss11_nand_smc_config);
> +
> +	at91_add_device_nand(&nand_pdata);
> +}
> +
> +static struct at91_ether_platform_data macb_pdata = {
> +	.phy_addr = 0,
> +	.flags = AT91SAM_ETX2_ETX3_ALTERNATIVE,
> +};
> +
> +static void dss11_phy_reset(void)
> +{
> +	unsigned long rstc;
> +	at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC);
> +
> +	at91_set_gpio_input(AT91_PIN_PA14, 0);
> +	at91_set_gpio_input(AT91_PIN_PA15, 0);
> +	at91_set_gpio_input(AT91_PIN_PA17, 0);
> +	at91_set_gpio_input(AT91_PIN_PA25, 0);
> +	at91_set_gpio_input(AT91_PIN_PA26, 0);
> +	at91_set_gpio_input(AT91_PIN_PA28, 0);
> +
> +	rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
> +
> +	/* Need to reset PHY -> 500ms reset */
> +	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> +				     (AT91_RSTC_ERSTL & (0x0d << 8)) |
> +				     AT91_RSTC_URSTEN);
> +
> +	at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
> +
> +	/* Wait for end hardware reset */
> +	while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
> +
> +	/* Restore NRST value */
> +	at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> +				     (rstc) |
> +				     AT91_RSTC_URSTEN);
> +}
> +
> +static struct atmel_mci_platform_data dss11_mci_data = {
> +	.bus_width	= 4,
> +	.host_caps	= MMC_MODE_HS,
> +};
> +
> +static struct at91_usbh_data dss11_usbh_data = {
> +	.ports		= 2,
> +};
> +
> +static int dss11_mem_init(void)
> +{
> +	at91_add_device_sdram(64 * 1024 * 1024);
> +
> +	return 0;
> +}
> +mem_initcall(dss11_mem_init);
> +
> +static int dss11_devices_init(void)
> +{
> +	dss11_add_device_nand();
> +	dss11_phy_reset();
> +	at91_add_device_eth(&macb_pdata);
> +	at91_add_device_mci(1, &dss11_mci_data);
> +	at91_add_device_usbh_ohci(&dss11_usbh_data);
> +
> +	armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
> +	armlinux_set_architecture(MACH_TYPE_DSS11);
> +
> +	devfs_add_partition("nand0", 0x00000, 0x20000, PARTITION_FIXED, "bootstrap");
> +	dev_add_bb_dev("bootstrap", "bootstrap.bb");
> +	devfs_add_partition("nand0", 0x20000, 0x40000, PARTITION_FIXED, "barebox");
> +	dev_add_bb_dev("barebox", "barebox.bb");
> +	devfs_add_partition("nand0", 0x60000, 0x40000, PARTITION_FIXED, "barebox-env");
> +	dev_add_bb_dev("barebox-env", "env0");
> +
> +	return 0;
> +}
> +device_initcall(dss11_devices_init);
> +
> +static int dss11_console_init(void)
> +{
> +	at91_register_uart(0, 0);
> +	return 0;
> +}
> +console_initcall(dss11_console_init);
> diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
> index 2ac23b5..e0e17bb 100644
> --- a/arch/arm/mach-at91/Kconfig
> +++ b/arch/arm/mach-at91/Kconfig
> @@ -20,6 +20,7 @@ config BOARDINFO
>  	default "Ronetix PM9261" if MACH_PM9261
>  	default "Ronetix PM9263" if MACH_PM9263
>  	default "Ronetix PM9G45" if MACH_PM9G45
> +	default "Aizo dSS11" if MACH_DSS11
please keep it sort
>  
>  config HAVE_NAND_ATMEL_BUSWIDTH_16
>  	bool
> @@ -175,6 +176,13 @@ config MACH_USB_A9G20
>  	  Select this if you are using a Calao Systems USB-A9G20.
>  	  <http://www.calao-systems.com>
>  
> +config MACH_DSS11
> +	bool "aizo dSS11"
> +	select HAVE_NAND_ATMEL_BUSWIDTH_16
> +	help
> +	  Select this if you are using aizo dSS11
> +	  that embeds only one SD/MMC slot.
ditto

Best Regards,
J.

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  reply	other threads:[~2011-12-09 15:05 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <1323187817-28668-1-git-send-email-m.grzeschik@pengutronix.de>
2011-12-09 11:28 ` [PATCH v2 1/7] storage/usb.c: fix test_unit_ready Michael Grzeschik
2011-12-09 11:28 ` [PATCH v2 2/7] atmel_mci: check for device id we use to address the right slot Michael Grzeschik
2011-12-09 11:28 ` [PATCH 3/7] at91sam9260_devices: properly set slot id Michael Grzeschik
2011-12-09 11:28 ` [PATCH 4/7] at91sam9260_devices: add flag to change ETX{2,3} pincfg on add_device_eth Michael Grzeschik
2011-12-09 14:56   ` *** PROBABLY SPAM *** " Jean-Christophe PLAGNIOL-VILLARD
2011-12-12 12:50     ` Sascha Hauer
2011-12-09 11:28 ` [PATCH v2 5/7] arm: update mach-types Michael Grzeschik
2011-12-09 11:29 ` [PATCH v2 6/7] platform: add support for aizo dSS11 Michael Grzeschik
2011-12-09 15:01   ` Jean-Christophe PLAGNIOL-VILLARD [this message]
2011-12-12 12:52     ` *** PROBABLY SPAM *** " Sascha Hauer
2011-12-09 11:29 ` [PATCH v2 7/7] dss11: add defconfig Michael Grzeschik

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20111209150131.GP23884@game.jcrosoft.org \
    --to=plagnioj@jcrosoft.com \
    --cc=barebox@lists.infradead.org \
    --cc=m.grzeschik@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox