From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from smtp3-g21.free.fr ([2a01:e0c:1:1599::12]) by merlin.infradead.org with esmtp (Exim 4.76 #1 (Red Hat Linux)) id 1Ru67x-0006N5-Tg for barebox@lists.infradead.org; Sun, 05 Feb 2012 17:43:51 +0000 Date: Sun, 5 Feb 2012 18:43:40 +0100 From: Eric =?ISO-8859-1?B?QuluYXJk?= Message-ID: <20120205184340.1bddd53a@eb-e6520> In-Reply-To: References: <20120205155201.4086003e@eb-e6520> Mime-Version: 1.0 List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Sender: barebox-bounces@lists.infradead.org Errors-To: barebox-bounces+u.kleine-koenig=pengutronix.de@lists.infradead.org Subject: Re: how do i add the defn for the beagle xM to barebox? To: "Robert P. J. Day" Cc: barebox@lists.infradead.org Le Sun, 5 Feb 2012 10:37:59 -0500 (EST), "Robert P. J. Day" a =E9crit : > On Sun, 5 Feb 2012, Eric B=E9nard wrote: > = > > Hi Robert, > > > > Le Sun, 5 Feb 2012 06:52:28 -0500 (EST), > > "Robert P. J. Day" a =E9crit : > > > thoughts? i'd actually like to make the tweaks one at a time so > > > that the git log shows clearly how the two boards differ one feature > > > at a time. > > > > By sensing a few GPIO, you can easily check which board you are running > > barebox on and thus have ony binary which supports all beagleboards > > (as already done in u-boot). > > > > Check around line 108 in u-boot's beagle support for the details : > > http://git.denx.de/?p=3Du-boot.git;a=3Dblob;f=3Dboard/ti/beagle/beagle.= c;h=3D5c04b34e1ab0140aca93e7752c8672ce7aebc0b9;hb=3DHEAD > > > > So in the end you can register the nand support only if you run on a > > board which has a NAND flash and have one defconfig for all > > beagleboards (some tweaks in the clock settings may be nedded - > > especially for USB IIRC - as beagle XM is built around a DM3730 which > > can run at 1GHz when older beagles had older OMAP3530 limited to > > 720MHz). > = > hmmmm ... i see one possible problem that maybe means i just haven't > read far enough. in u-boot, in that beagle.c file, here's a chunk of > code that identifies the NAND chip, of which there is none on the xM: > = > /* > * We need to identify what PoP memory is on the board so that > * we know what timings to use. If we can't identify it then > * we know it's an xM. To map the ID values please see nand_ids.c > */ > identify_nand_chip(&pop_mfr, &pop_id); > = > *mr =3D MICRON_V_MR_165; > switch (get_board_revision()) { > case REVISION_C4: > if (pop_mfr =3D=3D NAND_MFR_STMICRO && pop_id =3D=3D 0xba= ) { > /* 512MB DDR */ > *mcfg =3D NUMONYX_V_MCFG_165(512 << 20); > *ctrla =3D NUMONYX_V_ACTIMA_165; > *ctrlb =3D NUMONYX_V_ACTIMB_165; > *rfr_ctrl =3D SDP_3430_SDRC_RFR_CTRL_165MHz; > break; > } else if (pop_mfr =3D=3D NAND_MFR_MICRON && pop_id =3D= =3D 0xbc) { > /* Beagleboard Rev C5, 256MB DDR */ > *mcfg =3D MICRON_V_MCFG_200(256 << 20); > *ctrla =3D MICRON_V_ACTIMA_200; > *ctrlb =3D MICRON_V_ACTIMB_200; > *rfr_ctrl =3D SDP_3430_SDRC_RFR_CTRL_200MHz; > break; > } > case REVISION_XM_A: > case REVISION_XM_B: > case REVISION_XM_C: > if (pop_mfr =3D=3D 0) { > /* 256MB DDR */ > *mcfg =3D MICRON_V_MCFG_200(256 << 20); > *ctrla =3D MICRON_V_ACTIMA_200; > *ctrlb =3D MICRON_V_ACTIMB_200; > *rfr_ctrl =3D SDP_3430_SDRC_RFR_CTRL_200MHz; > } else { > /* 512MB DDR */ > *mcfg =3D NUMONYX_V_MCFG_165(512 << 20); > *ctrla =3D NUMONYX_V_ACTIMA_165; > *ctrlb =3D NUMONYX_V_ACTIMB_165; > *rfr_ctrl =3D SDP_3430_SDRC_RFR_CTRL_165MHz; > } > break; > ... snip ... > = > ok, i can see how that works, but if you need to test this way, it > means that you'll constantly be overriding the CONFIG settings in the > beagle defconfig file. > = > if i read you correctly, then one should be able to use the same > defconfig file for both a regular beagle and an xM. but the current > barebox beagle xload defconfig file contains stuff like: > = > CONFIG_MTD=3Dy > # CONFIG_MTD_WRITE is not set > # CONFIG_MTD_OOB_DEVICE is not set > CONFIG_NAND=3Dy > # CONFIG_NAND_ECC_SOFT is not set > # CONFIG_NAND_ECC_HW_SYNDROME is not set > # CONFIG_NAND_ECC_HW_NONE is not set > # CONFIG_NAND_INFO is not set > # CONFIG_NAND_BBT is not set > CONFIG_NAND_OMAP_GPMC=3Dy > = > which is fine for a regular beagle but totally wrong for an xM. does > this mean that, with an xM, i'd include the same (incorrect) defconfig > file, and have to be constantly overriding some of those settings? > = > i can see how getting the board revision lets you test how to do > things differently across a related set of boards. but the difference > between a regular beagle and an xM is *sizable* when you're talking > about NAND versus no NAND. ideally, i'd like to have that board > revision test available in the defconfig file itself. :-) > = This is the case where u-boot is built with SPL thus reoplacing x-load : they always read NAND ID as some XM boards were mounted with Numonyx POP which includes NAND and 166MHz RAM when mot XM boards have a POP with only 200MHz DDR (and in that case manufacturer ID is 0). So even on a XM you need to check the NAND ID to set the right RAM settings. Eric -- = http://eukrea.com/en/news/104-2012 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox