Re: [PATCH 6/7] mx53-loco: add board revision support

[Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>]

On 01:27 Tue 21 Feb     , Eric Bénard wrote:
> - this is taken from freescale-mx35-3-stack/3stack.c and allows
> this board to run Freescale's kernel which relies on the system
> revision to configure the correct PMIC.
> 
> - On rev0 boards (with DA9053), the log is :
> detected i.MX53 rev 2.1
> MCIMX53-START board 1.0
> 
> On newer boards (rev A or B with MC34708), the log is :
> mc34708-i2c@mc34708-i2c0: MC34708 ID: 0x0014
> detected i.MX53 rev 2.1
> MCIMX53-START-R board 1.0 rev B
> 
> Signed-off-by: Eric Bénard <eric@eukrea.com>
> ---
>  arch/arm/boards/freescale-mx53-loco/board.c |   51 +++++++++++++++++++++++++++
>  1 files changed, 51 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/boards/freescale-mx53-loco/board.c b/arch/arm/boards/freescale-mx53-loco/board.c
> index 66ff040..6c0e1d1 100644
> --- a/arch/arm/boards/freescale-mx53-loco/board.c
> +++ b/arch/arm/boards/freescale-mx53-loco/board.c
> @@ -103,6 +103,31 @@ static struct i2c_board_info i2c_devices[] = {
>  	},
>  };
>  
> +/*
> + * Revision to be passed to kernel. The kernel provided
> + * by freescale relies on this.
> + *
> + * C --> CPU type
> + * S --> Silicon revision
> + * B --> Board rev
> + *
> + * 31    20     16     12    8      4     0
> + *        | Cmaj | Cmin | B  | Smaj | Smin|
> + *
> + * e.g 0x00053120 --> i.MX35, Cpu silicon rev 2.0, Board rev 2
> +*/
> +static unsigned int loco_system_rev = 0x00053000;
> +
> +static void set_silicon_rev( int rev)
> +{
> +	loco_system_rev = loco_system_rev | (rev & 0xFF);
> +}
> +
> +static void set_board_rev(int rev)
> +{
> +	loco_system_rev =  (loco_system_rev & ~(0xF << 8)) | (rev & 0xF) << 8;
> +}
> +
>  static int loco_mem_init(void)
>  {
>  	arm_add_mem_device("ram0", 0x70000000, SZ_512M);
> @@ -149,6 +174,8 @@ static int loco_devices_init(void)
>  
>  	loco_fec_reset();
>  
> +	set_silicon_rev(imx_silicon_revision());
> +
>  	armlinux_set_bootparams((void *)0x70000100);
>  	armlinux_set_architecture(MACH_TYPE_MX53_LOCO);
>  
> @@ -177,3 +204,27 @@ static int loco_console_init(void)
>  }
>  
>  console_initcall(loco_console_init);
> +
> +static int loco_pmic_init(void)
> +{
> +	struct mc34708 *mc34708;
> +	int rev;
> +
> +	mc34708 = mc34708_get();
please check the file exist
> +	if (!mc34708) {
> +		/* so we have a DA9053 based board */
> +		printf("MCIMX53-START board 1.0\n");
> +		armlinux_set_revision(loco_system_rev);
please do not duplicate it
> +		return 0;
> +	}
> +
> +	/* get the board revision from fuse */
> +	rev = readl(MX53_IIM_BASE_ADDR + 0x878);
> +	set_board_rev(rev);
> +	printf("MCIMX53-START-R board 1.0 rev %c\n", (rev == 1) ? 'A' : 'B' );
> +	armlinux_set_revision(loco_system_rev);
> +
> +	return 0;
> +}
Best Regards,
J.

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox