From: Sascha Hauer <s.hauer@pengutronix.de>
To: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH v5] ARM: at91: Add Telit EVK-PRO3 board support
Date: Wed, 30 Jan 2013 22:53:34 +0100 [thread overview]
Message-ID: <20130130215334.GH1906@pengutronix.de> (raw)
In-Reply-To: <1359458161-22709-1-git-send-email-fabio.porcedda@gmail.com>
On Tue, Jan 29, 2013 at 12:16:01PM +0100, Fabio Porcedda wrote:
> http://www.telit.com
>
> Based on at91sam9260ek board support.
>
> Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Applied, thanks
Sascha
> ---
> v5:
> - fix mci configuration
> - some codestyle improvements
> v4:
> - use a gpio for dfu
> - remove HAVE_NAND_ATMEL_BUSWIDTH_16
> v3:
> - add dfu support
> - init.c: reduced bootstrap size
> - init.c: moved istructions from evk_add_device_nand function to the struct
> - init.c: remove blank line
> - renamed to telit-evk-pro3
>
> v2:
> - init.c: remove 9260ek and g20ek references
> - init.c: rename ek_ -> evk_
> - init.c: cleanup headers
> - init.c: use clock framework
> - init.c: remove function ek_set_board_type
> - init.c: remove bus_width_16 initialization
>
> arch/arm/Makefile | 1 +
> arch/arm/boards/telit-evk-pro3/Makefile | 1 +
> arch/arm/boards/telit-evk-pro3/config.h | 6 +
> arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi | 10 ++
> .../boards/telit-evk-pro3/env/init/config-board | 8 +
> .../boards/telit-evk-pro3/env/init/mtdparts-nand | 11 ++
> arch/arm/boards/telit-evk-pro3/env/init/usb | 40 +++++
> arch/arm/boards/telit-evk-pro3/init.c | 176 +++++++++++++++++++++
> arch/arm/configs/telit_evk_pro3_defconfig | 73 +++++++++
> arch/arm/mach-at91/Kconfig | 8 +
> 10 files changed, 334 insertions(+)
> create mode 100644 arch/arm/boards/telit-evk-pro3/Makefile
> create mode 100644 arch/arm/boards/telit-evk-pro3/config.h
> create mode 100644 arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi
> create mode 100644 arch/arm/boards/telit-evk-pro3/env/init/config-board
> create mode 100644 arch/arm/boards/telit-evk-pro3/env/init/mtdparts-nand
> create mode 100644 arch/arm/boards/telit-evk-pro3/env/init/usb
> create mode 100644 arch/arm/boards/telit-evk-pro3/init.c
> create mode 100644 arch/arm/configs/telit_evk_pro3_defconfig
>
> diff --git a/arch/arm/Makefile b/arch/arm/Makefile
> index a36adfb..60661eb 100644
> --- a/arch/arm/Makefile
> +++ b/arch/arm/Makefile
> @@ -94,6 +94,7 @@ board-$(CONFIG_MACH_EUKREA_CPUIMX35) := eukrea_cpuimx35
> board-$(CONFIG_MACH_EUKREA_CPUIMX51SD) := eukrea_cpuimx51
> board-$(CONFIG_MACH_FREESCALE_MX25_3STACK) := freescale-mx25-3-stack
> board-$(CONFIG_MACH_FREESCALE_MX35_3STACK) := freescale-mx35-3-stack
> +board-$(CONFIG_MACH_GE863) := telit-evk-pro3
> board-$(CONFIG_MACH_IMX21ADS) := imx21ads
> board-$(CONFIG_MACH_IMX27ADS) := imx27ads
> board-$(CONFIG_MACH_IMX233_OLINUXINO) := imx233-olinuxino
> diff --git a/arch/arm/boards/telit-evk-pro3/Makefile b/arch/arm/boards/telit-evk-pro3/Makefile
> new file mode 100644
> index 0000000..eb072c0
> --- /dev/null
> +++ b/arch/arm/boards/telit-evk-pro3/Makefile
> @@ -0,0 +1 @@
> +obj-y += init.o
> diff --git a/arch/arm/boards/telit-evk-pro3/config.h b/arch/arm/boards/telit-evk-pro3/config.h
> new file mode 100644
> index 0000000..7aeff30
> --- /dev/null
> +++ b/arch/arm/boards/telit-evk-pro3/config.h
> @@ -0,0 +1,6 @@
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define AT91_MAIN_CLOCK 6000000 /* 6.000 MHz crystal */
> +
> +#endif /* __CONFIG_H */
> diff --git a/arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi b/arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi
> new file mode 100644
> index 0000000..1987492
> --- /dev/null
> +++ b/arch/arm/boards/telit-evk-pro3/env/boot/nand-ubi
> @@ -0,0 +1,10 @@
> +#!/bin/sh
> +
> +if [ "$1" = menu ]; then
> + boot-menu-add-entry "$0" "nand (UBI)"
> + exit
> +fi
> +
> +global.bootm.image="/dev/nand0.kernel.bb"
> +#global.bootm.oftree="/env/oftree"
> +global.linux.bootargs.dyn.root="root=ubi0:rootfs ubi.mtd=nand0.rootfs rootfstype=ubifs"
> diff --git a/arch/arm/boards/telit-evk-pro3/env/init/config-board b/arch/arm/boards/telit-evk-pro3/env/init/config-board
> new file mode 100644
> index 0000000..741b902
> --- /dev/null
> +++ b/arch/arm/boards/telit-evk-pro3/env/init/config-board
> @@ -0,0 +1,8 @@
> +#!/bin/sh
> +
> +# board defaults, do not change in running system. Change /env/config
> +# instead
> +
> +global.hostname=evk-pro3
> +global.linux.bootargs.base="console=ttyS0,115200"
> +global.boot.default=nand-ubi
> diff --git a/arch/arm/boards/telit-evk-pro3/env/init/mtdparts-nand b/arch/arm/boards/telit-evk-pro3/env/init/mtdparts-nand
> new file mode 100644
> index 0000000..58e859b
> --- /dev/null
> +++ b/arch/arm/boards/telit-evk-pro3/env/init/mtdparts-nand
> @@ -0,0 +1,11 @@
> +#!/bin/sh
> +
> +if [ "$1" = menu ]; then
> + init-menu-add-entry "$0" "NAND partitions"
> + exit
> +fi
> +
> +mtdparts="0xC0000(nand0.bootstrap),256k(nand0.barebox)ro,128k(nand0.bareboxenv),3M(nand0.kernel),-(nand0.rootfs)"
> +kernelname="atmel_nand"
> +
> +mtdparts-add -b -d nand0 -k ${kernelname} -p ${mtdparts}
> diff --git a/arch/arm/boards/telit-evk-pro3/env/init/usb b/arch/arm/boards/telit-evk-pro3/env/init/usb
> new file mode 100644
> index 0000000..47429f5
> --- /dev/null
> +++ b/arch/arm/boards/telit-evk-pro3/env/init/usb
> @@ -0,0 +1,40 @@
> +#!/bin/sh
> +
> +# Connect PC31 to GND to enable DFU
> +gpio_dfu=95
> +gpio_name="PC31"
> +gpio_wait=5
> +
> +product_id=0x1234
> +vendor_id=0x4321
> +
> +dfu_config="/dev/nand0.bootstrap.bb(bootstrap)sr,/dev/nand0.barebox.bb(barebox)sr,/dev/nand0.kernel.bb(kernel)r,/dev/nand0.rootfs.bb(rootfs)r"
> +
> +echo
> +
> +if [ $at91_udc0.vbus != 1 ]; then
> + echo "No USB Device cable plugged, normal boot"
> + exit
> +fi
> +
> +gpio_get_value ${gpio_dfu}
> +if [ $? = 0 ]; then
> + echo "${gpio_name} low value detected wait ${gpio_wait}s"
> + timeout -s -a ${gpio_wait}
> +
> + if [ $at91_udc0.vbus != 1 ]; then
> + echo "No USB Device cable plugged, normal boot"
> + exit
> + fi
> +
> + gpio_get_value ${gpio_dfu}
> + if [ $? = 0 ]; then
> + echo "Start DFU Mode"
> + dfu ${dfu_config} -P ${product_id} -V ${vendor_id}
> + exit
> + fi
> +fi
> +
> +global.autoboot_timeout=16
> +echo "enable tty over USB Device, increase the boot delay to ${global.autoboot_timeout}s"
> +usbserial
> diff --git a/arch/arm/boards/telit-evk-pro3/init.c b/arch/arm/boards/telit-evk-pro3/init.c
> new file mode 100644
> index 0000000..9ff828d
> --- /dev/null
> +++ b/arch/arm/boards/telit-evk-pro3/init.c
> @@ -0,0 +1,176 @@
> +/*
> + * Copyright (C) 2007 Sascha Hauer, Pengutronix
> + * Copyright (C) 2013 Fabio Porcedda <fabio.porcedda@gmail.com>, Telit
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <asm/armlinux.h>
> +#include <common.h>
> +#include <gpio.h>
> +#include <init.h>
> +#include <linux/clk.h>
> +#include <mach/at91_rstc.h>
> +#include <mach/at91sam9_smc.h>
> +#include <mach/board.h>
> +#include <mach/io.h>
> +#include <nand.h>
> +
> +#define BOOTSTRAP_SIZE 0xC0000
> +
> +static struct atmel_nand_data nand_pdata = {
> + .ale = 21,
> + .cle = 22,
> + .det_pin = -EINVAL,
> + .rdy_pin = AT91_PIN_PC13,
> + .enable_pin = AT91_PIN_PC14,
> + .on_flash_bbt = 1,
> +};
> +
> +static struct sam9_smc_config evk_nand_smc_config = {
> + .ncs_read_setup = 0,
> + .nrd_setup = 1,
> + .ncs_write_setup = 0,
> + .nwe_setup = 1,
> +
> + .ncs_read_pulse = 3,
> + .nrd_pulse = 3,
> + .ncs_write_pulse = 3,
> + .nwe_pulse = 3,
> +
> + .read_cycle = 5,
> + .write_cycle = 5,
> +
> + .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
> + AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
> + .tdf_cycles = 2,
> +};
> +
> +static void evk_add_device_nand(void)
> +{
> + /* configure chip-select 3 (NAND) */
> + sam9_smc_configure(0, 3, &evk_nand_smc_config);
> +
> + at91_add_device_nand(&nand_pdata);
> +}
> +
> +static struct at91_ether_platform_data macb_pdata = {
> + .is_rmii = 1,
> + .phy_addr = 0,
> +};
> +
> +static void evk_phy_reset(void)
> +{
> + unsigned long rstc;
> + struct clk *clk = clk_get(NULL, "macb_clk");
> +
> + clk_enable(clk);
> +
> + at91_set_gpio_input(AT91_PIN_PA14, 0);
> + at91_set_gpio_input(AT91_PIN_PA15, 0);
> + at91_set_gpio_input(AT91_PIN_PA17, 0);
> + at91_set_gpio_input(AT91_PIN_PA25, 0);
> + at91_set_gpio_input(AT91_PIN_PA26, 0);
> + at91_set_gpio_input(AT91_PIN_PA28, 0);
> +
> + rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
> +
> + /* Need to reset PHY -> 500ms reset */
> + at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
> + (AT91_RSTC_ERSTL & (0x0d << 8)) |
> + AT91_RSTC_URSTEN);
> +
> + at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
> +
> + /* Wait for end hardware reset */
> + while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL))
> + ;
> +
> + /* Restore NRST value */
> + at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY | (rstc) | AT91_RSTC_URSTEN);
> +}
> +
> +/*
> + * MCI (SD/MMC)
> + */
> +#if defined(CONFIG_MCI_ATMEL)
> +static struct atmel_mci_platform_data __initdata evk_mci_data = {
> + .bus_width = 4,
> + .detect_pin = AT91_PIN_PA27,
> + .wp_pin = AT91_PIN_PA25,
> +};
> +
> +static void evk_usb_add_device_mci(void)
> +{
> + at91_add_device_mci(0, &evk_mci_data);
> +}
> +#else
> +static void evk_usb_add_device_mci(void) {}
> +#endif
> +
> +/*
> + * USB Host port
> + */
> +static struct at91_usbh_data __initdata evk_usbh_data = {
> + .ports = 2,
> + .vbus_pin = { -EINVAL, -EINVAL },
> +};
> +
> +/*
> + * USB Device port
> + */
> +static struct at91_udc_data __initdata evk_udc_data = {
> + .vbus_pin = AT91_PIN_PC4,
> + .pullup_pin = -EINVAL, /* pull-up driven by UDC */
> +};
> +
> +static int evk_mem_init(void)
> +{
> + at91_add_device_sdram(0);
> +
> + return 0;
> +}
> +mem_initcall(evk_mem_init);
> +
> +static int evk_devices_init(void)
> +{
> + evk_add_device_nand();
> + evk_phy_reset();
> + at91_add_device_eth(0, &macb_pdata);
> + at91_add_device_usbh_ohci(&evk_usbh_data);
> + at91_add_device_udc(&evk_udc_data);
> + evk_usb_add_device_mci();
> +
> + armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
> +
> + devfs_add_partition("nand0", 0x00000, BOOTSTRAP_SIZE,
> + DEVFS_PARTITION_FIXED, "bootstrap_raw");
> + dev_add_bb_dev("bootstrap_raw", "bootstrap");
> + devfs_add_partition("nand0", BOOTSTRAP_SIZE, SZ_256K,
> + DEVFS_PARTITION_FIXED, "self_raw");
> + dev_add_bb_dev("self_raw", "self0");
> + devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K, SZ_128K,
> + DEVFS_PARTITION_FIXED, "env_raw");
> + dev_add_bb_dev("env_raw", "env0");
> + devfs_add_partition("nand0", BOOTSTRAP_SIZE + SZ_256K + SZ_128K,
> + SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
> + dev_add_bb_dev("env_raw1", "env1");
> +
> + return 0;
> +}
> +device_initcall(evk_devices_init);
> +
> +static int evk_console_init(void)
> +{
> + at91_register_uart(0, 0);
> + return 0;
> +}
> +console_initcall(evk_console_init);
> diff --git a/arch/arm/configs/telit_evk_pro3_defconfig b/arch/arm/configs/telit_evk_pro3_defconfig
> new file mode 100644
> index 0000000..050d176
> --- /dev/null
> +++ b/arch/arm/configs/telit_evk_pro3_defconfig
> @@ -0,0 +1,73 @@
> +CONFIG_ARCH_AT91SAM9260=y
> +CONFIG_MACH_GE863=y
> +CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000
> +CONFIG_AEABI=y
> +# CONFIG_CMD_ARM_CPUINFO is not set
> +CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
> +CONFIG_PBL_IMAGE=y
> +CONFIG_MMU=y
> +CONFIG_EXPERIMENTAL=y
> +CONFIG_PROMPT="EVK-PRO3:"
> +CONFIG_LONGHELP=y
> +CONFIG_PROMPT_HUSH_PS2="y"
> +CONFIG_HUSH_FANCY_PROMPT=y
> +CONFIG_CMDLINE_EDITING=y
> +CONFIG_AUTO_COMPLETE=y
> +CONFIG_CONSOLE_ACTIVATE_ALL=y
> +CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
> +CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/telit-evk-pro3/env"
> +CONFIG_CMD_EDIT=y
> +CONFIG_CMD_SLEEP=y
> +CONFIG_CMD_SAVEENV=y
> +CONFIG_CMD_EXPORT=y
> +CONFIG_CMD_PRINTENV=y
> +CONFIG_CMD_READLINE=y
> +CONFIG_CMD_TFTP=y
> +CONFIG_CMD_ECHO_E=y
> +CONFIG_CMD_LOADB=y
> +CONFIG_CMD_MEMINFO=y
> +CONFIG_CMD_FLASH=y
> +CONFIG_CMD_UBIFORMAT=y
> +CONFIG_CMD_BOOTM_SHOW_TYPE=y
> +CONFIG_CMD_BOOTM_INITRD=y
> +CONFIG_CMD_BOOTM_OFTREE=y
> +CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
> +CONFIG_CMD_UIMAGE=y
> +# CONFIG_CMD_BOOTU is not set
> +CONFIG_CMD_RESET=y
> +CONFIG_CMD_GO=y
> +CONFIG_CMD_OFTREE=y
> +CONFIG_CMD_MTEST=y
> +CONFIG_CMD_MTEST_ALTERNATIVE=y
> +CONFIG_CMD_TIMEOUT=y
> +CONFIG_CMD_PARTITION=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_LED=y
> +CONFIG_CMD_LED_TRIGGER=y
> +CONFIG_NET=y
> +CONFIG_NET_DHCP=y
> +CONFIG_NET_NFS=y
> +CONFIG_NET_PING=y
> +CONFIG_NET_NETCONSOLE=y
> +CONFIG_DRIVER_NET_MACB=y
> +# CONFIG_SPI is not set
> +CONFIG_MTD=y
> +# CONFIG_MTD_OOB_DEVICE is not set
> +CONFIG_NAND=y
> +# CONFIG_NAND_ECC_HW is not set
> +# CONFIG_NAND_ECC_HW_SYNDROME is not set
> +# CONFIG_NAND_ECC_HW_NONE is not set
> +CONFIG_NAND_ATMEL=y
> +CONFIG_UBI=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_DFU=y
> +CONFIG_USB_GADGET_SERIAL=y
> +CONFIG_MCI=y
> +CONFIG_MCI_STARTUP=y
> +CONFIG_MCI_ATMEL=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_LED_TRIGGERS=y
> +CONFIG_FS_TFTP=y
> +CONFIG_FS_FAT=y
> +CONFIG_FS_FAT_LFN=y
> diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
> index 945e27b..8b574a8 100644
> --- a/arch/arm/mach-at91/Kconfig
> +++ b/arch/arm/mach-at91/Kconfig
> @@ -46,6 +46,7 @@ config BOARDINFO
> default "Calao TNY-A9263" if MACH_TNY_A9263
> default "Calao TNY-A9G20" if MACH_TNY_A9G20
> default "Calao QIL-A9260" if MACH_QIL_A9260
> + default "Telit EVK-PRO3" if MACH_GE863
>
> config HAVE_NAND_ATMEL_BUSWIDTH_16
> bool
> @@ -235,6 +236,13 @@ config MACH_USB_A9260
> Select this if you are using a Calao Systems USB-A9260.
> <http://www.calao-systems.com>
>
> +config MACH_GE863
> + bool "Telit EVK-PRO3"
> + select HAVE_DEFAULT_ENVIRONMENT_NEW
> + help
> + Say y here if you are using Telit EVK-PRO3 with GE863-PRO3
> + <http://www.telit.com>
> +
> endchoice
>
> endif
> --
> 1.8.1.1
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
prev parent reply other threads:[~2013-01-30 21:53 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-01-29 11:16 Fabio Porcedda
2013-01-30 21:53 ` Sascha Hauer [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130130215334.GH1906@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=barebox@lists.infradead.org \
--cc=fabio.porcedda@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox