* v2013.06.0
@ 2013-06-03 7:33 Sascha Hauer
0 siblings, 0 replies; only message in thread
From: Sascha Hauer @ 2013-06-03 7:33 UTC (permalink / raw)
To: barebox
Another month, another release. Here is v2013.06.0.
Sascha
----------------------------------------------------------------
Alexander Shiyan (22):
Makefile: Create empty <config.h> if this header file is not needed by board
Remove unused config.h
ARM: cpuimx51: Use custom padctrl for fec
ARM: i.MX: Update MX2x iomux definitions
ARM: i.MX: Update MX51 iomux definitions
Remove unimplemented usb_driver_unregister declaration
GPIO: Rename "drivers/gpio.c" to "drivers/gpiolib.c"
ARM: i.MX: Move GPIO driver to drivers/gpio
ata: Remove wrong DISK_DRIVE symbol
ARM: omap: Remove wrong OMAP_CLOCK_ALL symbol
ARM: netx: Remove references for missing boards
ARM: imx: Fix incorrect Kconfig symbols for some boards
ARM: at91 gpio: Fix possible null pointer dereference
ARM: at91 smc: Fix possible uninitialized variable
MCI: atmel: Fix possible null pointer dereference
MCI: imx: Fix possible null pointer dereference
NAND: imx: Fix memory leak
ARM: pcm038: Add descriptions for pin-groups
ARM: pcm038: Add definition for SPI chipselect 0
ARM: pcm038: Add definition for FEC reset
ARM: ccmx51js: Add support for USB Host1
ARM: ccmx51: Another fix SDRAM size detection
Alexandre Belloni (1):
sama5d3xek: correct rootfs nand partition
Andreas Pretzsch (2):
ARM i.MX31: cleanup MX31_ prefix: fix leftover IOMUXC_BASE defines
ARM i.MX31 pcm037: fix erroneous IOMUX GPR setup in pcm037_usb_init()
Antony Pavlov (2):
ARM: remove unused clkdev.h
gpio: fix typos
Enrico Scholz (3):
ARM v7: fix mmu-off operation
ARM v7: v7_mmu_cache_flush(): do not restore r0-r3 (minor optimization)
ARM v7: added v7_mmu_cache_invalidate()
Eric Bénard (2):
nand_base: detect more ONFI flash
nand_base: sync flash detection functions with linux 3.9's code
Jan Luebbe (10):
commands: i2c: change 0X to 0x
mtd: update NAND manufacturer names from the kernel
commands: the crc command is actually called crc32
omap: move to common bootsource framework
beaglebone: remove stray semicolon
Makefile: drop duplicate definition of cmd_objcopy
am33xx: add defines for GPIOs
m33xx-clock: configure PLLs based on oscillator frequency
m33xx-clock: remove unused code
defaultenv-2: init: display prompt after running /env/init/*
Jan Weitzel (1):
ARM: mmu: Use PAGE_ALIGN in dma_free_coherent
Jean-Christophe PLAGNIOL-VILLARD (4):
highbank: switch to defaultenv-2
at91sam9m10g45ek: add spi dataflash supprt
commands/mem.c: drop non used DEVMEM
qt1070: drop non used buf
Juergen Beisert (7):
ARM/MXS: add more ROM code related documentation
MXS/MCI: simplify reset of the MCI device block
MCI/Core: increase the transmission frequency while card detection
MCI/Core: honor transmission limits at the card's side
MCI/MXS: report a better matching error code when the transfer fails
MCI/MXS: fix signed/unsigned mismatch
MXS: fix SoC detecting
Lucas Stach (13):
tegra: switch to proper CPU type
tegra: unify spelling in Kconfig with Linux kernel
tegra: introduce Tegra 20 SoC type
tegra: move default textbase
tegra: switch to DT only
tegra: add driver for the clock and reset module
tegra: add T20 timer driver
tegra: add T20 power management controller driver
tegra: add common lowlevel startup
tegra: add generic debug UART support
tegra: add generic meminit
tegra: add GPIO controller driver
arm: properly init alignment trap bit
Masaki Muranaka (1):
Avoid build error on "config SPI" is y
Nicolas Pitre (1):
ARM: fix the memset fix
Sascha Hauer (68):
param: Add dev member to struct param_d
param: refactor __dev_add_param
param: Add integer and boolean parameter helpers
param: Add ip address convenience function
net: ksz8864: Use dev_add_param_bool for enable parameter
net: store ethernet device parameters in device
netconsole: use dev_add_param_* helpers
param: remove now unused dev_[gs]et_param_ip
treewide: Use dev_add_param_int_ro where possible
mci: Use dev_add_param_int for probe parameter
ata: Use dev_add_param_bool for probe parameter
fb: Use dev_add_param_bool for enable parameter
fb: imxfb: Use dev_add_param_int for alpha parameter
fb: imx-ipu-fb: Use dev_add_param_int for alpha parameter
param: pass param to dev_remove_param
pwm: Use dev_add_param_int for pwm parameters
ARM: i.MX: iim: Use dev_add_param_bool for parameters
console: Use dev_add_param_int for baudrate parameter
mtd: Nand: Use dev_add_param_bool for erasebad parameter
USB gadget at91: Use dev_add_param_bool for vbus parameter
ARM: MXS: ocotp: Use dev_add_param_bool for parameter
memory commands: export common functions
memory commands: move memory_display to separate file
Use a common define for RW_BUF_SIZE
memory commands: cleanup initialization
memory commands: make rw_buf global
memory commands: separate into one file per command
Add memory modify command (mm)
defaultenv-2: net: use oftree when existing
of: parse phandles before probing devices
of: Add of_property_read_string_index()
of: Allow multiple resources in 'reg' property
of: read resource names from devicetree
of: partitions: pass struct cdev as argument
of: partitions: create bb device for nand flashes
Add initial pinctrl support
pinctrl: switch i.MX iomux-v3 support to pinctrl
pinctrl: move imx-iomux-v2 to drivers/pinctrl/
pinctrl: move imx-iomux-v1 to drivers/pinctrl/
mci: imx-esdhc: remove cache snoop register access
Don't honor initrd load address
Merge branch 'for-next/atmel'
Merge branch 'for-next/gpio'
Merge branch 'for-next/imx'
Merge branch 'for-next/mci'
Merge branch 'for-next/memory-commands'
Merge branch 'for-next/misc'
Merge branch 'for-next/mtd'
Merge branch 'for-next/mxs'
Merge branch 'for-next/of'
Merge branch 'for-next/omap'
Merge branch 'for-next/param'
Merge branch 'for-next/remove-config-h'
Merge branch 'for-next/tegra'
ARM: i.MX: Allow disabling SDRAM autodetection
ARM: i.MX: ccxmx51: detect SDRAM size by board id
net: dhcp: Fix return value on ctrl-c
net: dhcp: Fix tftp servername handling
Merge branch 'pu/dhcp'
fdt: Fix dt memreserve entry
ARM: invalidate data caches during early init
pbl: Fix typo in make causing pbl files to be rebuilt
ARM: pbl: fix make dependencies
make: Add barebox_default_env.* to targets
ARM: zynq: Add cmd to generate zynq image
ARM: i.MX53 vincell: Fix lowlevel startup
ARM: pbl: Always call pbl make
Release v2013.06.0
Steffen Trumtrar (2):
defaultenv-2: Fix settings entry
ARM i.MX53: tqma53: fix console entry
Thomas Petazzoni (1):
scripts: allow lines longer than 80 cols with printf() in checkpatch
Uwe Kleine-König (1):
bootm: Simplify initrd address handling
Vicente Bergas (1):
OMAP4: add command to select next boot device priority
Makefile | 23 +-
arch/arm/Kconfig | 11 +-
arch/arm/Makefile | 20 +-
arch/arm/boards/archosg9/config.h | 1 -
arch/arm/boards/at91sam9m10g45ek/init.c | 18 +
arch/arm/boards/at91sam9m10ihd/hw_version.c | 6 +-
arch/arm/boards/at91sam9x5ek/hw_version.c | 6 +-
arch/arm/boards/avnet-zedboard/config.h | 4 -
arch/arm/boards/beagle/config.h | 17 -
arch/arm/boards/beaglebone/config.h | 17 -
arch/arm/boards/beaglebone/lowlevel.c | 2 +-
arch/arm/boards/ccxmx51/ccxmx51.c | 63 ++-
arch/arm/boards/ccxmx51/ccxmx51.h | 1 +
arch/arm/boards/ccxmx51/ccxmx51js.c | 15 +
arch/arm/boards/ccxmx51/config.h | 24 -
arch/arm/boards/ccxmx51/lowlevel.c | 4 +-
arch/arm/boards/chumby_falconwing/config.h | 17 -
arch/arm/boards/clep7212/config.h | 4 -
arch/arm/boards/crystalfontz-cfa10036/config.h | 16 -
arch/arm/boards/dmo-mx6-realq7/config.h | 4 -
arch/arm/boards/edb93xx/config.h | 4 -
arch/arm/boards/efika-mx-smartbook/config.h | 17 -
arch/arm/boards/eukrea_cpuimx27/config.h | 22 -
arch/arm/boards/eukrea_cpuimx51/config.h | 20 -
arch/arm/boards/eukrea_cpuimx51/eukrea_cpuimx51.c | 14 +-
arch/arm/boards/freescale-mx23-evk/config.h | 12 -
arch/arm/boards/freescale-mx28-evk/config.h | 16 -
arch/arm/boards/freescale-mx51-pdk/config.h | 20 -
arch/arm/boards/freescale-mx53-loco/config.h | 20 -
arch/arm/boards/freescale-mx53-smd/config.h | 20 -
arch/arm/boards/freescale-mx6-arm2/config.h | 4 -
arch/arm/boards/freescale-mx6-sabrelite/config.h | 4 -
arch/arm/boards/freescale-mx6-sabresd/config.h | 4 -
arch/arm/boards/guf-neso/config.h | 22 -
arch/arm/boards/guf-vincell/config.h | 24 -
arch/arm/boards/guf-vincell/lowlevel.c | 4 +-
arch/arm/boards/highbank/config.h | 5 -
arch/arm/boards/highbank/env/boot.d/010-ahci-boot | 1 +
arch/arm/boards/highbank/env/boot.d/011-ahci | 1 +
arch/arm/boards/highbank/env/boot.d/020-mmc-boot | 1 +
arch/arm/boards/highbank/env/boot.d/021-mmc | 1 +
arch/arm/boards/highbank/env/boot.d/030-net | 1 +
arch/arm/boards/highbank/env/boot.d/031-net-eth1 | 1 +
arch/arm/boards/highbank/env/boot/ahci | 21 +
arch/arm/boards/highbank/env/boot/ahci-boot | 21 +
arch/arm/boards/highbank/env/boot/mmc | 21 +
arch/arm/boards/highbank/env/boot/mmc-boot | 21 +
arch/arm/boards/highbank/env/boot/net | 18 +
arch/arm/boards/highbank/env/boot/net-eth1 | 18 +
arch/arm/boards/highbank/env/config | 33 --
arch/arm/boards/highbank/env/config-board | 11 +
arch/arm/boards/highbank/env/data/oftree | 4 +
.../env/{bin/init_board => init/001-dtb-probe} | 0
arch/arm/boards/highbank/env/init/automount | 27 ++
arch/arm/boards/highbank/env/init/ps1 | 9 +
arch/arm/boards/imx21ads/config.h | 22 -
arch/arm/boards/imx233-olinuxino/config.h | 21 -
arch/arm/boards/imx27ads/config.h | 22 -
arch/arm/boards/karo-tx28/config.h | 16 -
arch/arm/boards/karo-tx51/config.h | 17 -
arch/arm/boards/karo-tx53/config.h | 24 -
arch/arm/boards/mioa701/config.h | 22 -
arch/arm/boards/netx/config.h | 4 -
arch/arm/boards/nhk8815/config.h | 1 -
arch/arm/boards/omap343xdsp/config.h | 17 -
arch/arm/boards/omap3evm/config.h | 17 -
arch/arm/boards/panda/config.h | 1 -
arch/arm/boards/pcm037/pcm037.c | 6 +-
arch/arm/boards/pcm038/config.h | 22 -
arch/arm/boards/pcm038/pcm038.c | 14 +-
arch/arm/boards/pcm049/config.h | 1 -
arch/arm/boards/pcm051/config.h | 21 -
arch/arm/boards/phycard-a-l1/config.h | 18 -
arch/arm/boards/phycard-a-xl2/config.h | 1 -
arch/arm/boards/phycard-i.MX27/config.h | 22 -
arch/arm/boards/raspberry-pi/config.h | 4 -
arch/arm/boards/sama5d3xek/env/config | 2 +-
arch/arm/boards/sama5d3xek/hw_version.c | 6 +-
arch/arm/boards/toshiba-ac100/Makefile | 2 -
arch/arm/boards/toshiba-ac100/board.c | 8 -
arch/arm/boards/toshiba-ac100/config.h | 5 -
arch/arm/boards/toshiba-ac100/lowlevel.c | 10 -
arch/arm/boards/toshiba-ac100/serial.c | 39 --
arch/arm/boards/tqma53/config.h | 4 -
arch/arm/boards/tqma53/env/config-board | 2 +-
arch/arm/boards/versatile/config.h | 5 -
arch/arm/boards/vexpress/config.h | 5 -
arch/arm/configs/at91sam9m10g45ek_defconfig | 4 +-
arch/arm/configs/phycard_a_l1_defconfig | 1 -
arch/arm/configs/toshiba_ac100_defconfig | 7 +-
arch/arm/cpu/cache-armv7.S | 74 +--
arch/arm/cpu/cache.c | 21 +
arch/arm/cpu/mmu.c | 7 +-
arch/arm/cpu/start-pbl.c | 2 +
arch/arm/cpu/start.c | 2 +
arch/arm/dts/tegra20-paz00.dts | 12 +
arch/arm/dts/tegra20.dtsi | 41 ++
arch/arm/include/asm/barebox-arm-head.h | 2 +-
arch/arm/include/asm/cache.h | 5 +
arch/arm/lib/memset.S | 33 +-
arch/arm/mach-at91/gpio.c | 5 +-
arch/arm/mach-at91/sam9_smc.c | 8 +-
arch/arm/mach-highbank/Kconfig | 1 +
arch/arm/mach-imx/Kconfig | 15 +-
arch/arm/mach-imx/Makefile | 20 +-
arch/arm/mach-imx/esdctl.c | 14 +
arch/arm/mach-imx/iim.c | 65 +--
arch/arm/mach-imx/include/mach/esdctl.h | 1 +
arch/arm/mach-imx/include/mach/imx31-regs.h | 6 +-
arch/arm/mach-imx/include/mach/iomux-mx27.h | 6 -
arch/arm/mach-imx/include/mach/iomux-mx2x.h | 12 +-
arch/arm/mach-imx/include/mach/iomux-mx51.h | 28 +-
arch/arm/mach-imx/iomux-v3.c | 107 -----
arch/arm/mach-mxs/imx.c | 1 +
arch/arm/mach-mxs/ocotp.c | 34 +-
arch/arm/mach-netx/Kconfig | 16 -
arch/arm/mach-omap/Kconfig | 9 +-
arch/arm/mach-omap/Makefile | 1 +
arch/arm/mach-omap/am33xx_generic.c | 10 +-
arch/arm/mach-omap/boot_order.c | 83 ++++
arch/arm/mach-omap/include/mach/am33xx-clock.h | 18 +-
arch/arm/mach-omap/include/mach/am33xx-silicon.h | 6 +
arch/arm/mach-omap/include/mach/generic.h | 13 -
arch/arm/mach-omap/include/mach/omap4-silicon.h | 20 +
arch/arm/mach-omap/omap3_clock.c | 6 -
arch/arm/mach-omap/omap3_generic.c | 16 +-
arch/arm/mach-omap/omap4_generic.c | 44 +-
arch/arm/mach-omap/omap_generic.c | 15 +-
arch/arm/mach-omap/xload.c | 26 +-
arch/arm/mach-tegra/Kconfig | 53 ++-
arch/arm/mach-tegra/Makefile | 9 +-
arch/arm/mach-tegra/clock.c | 56 ---
arch/arm/mach-tegra/include/mach/gpio.h | 1 +
arch/arm/mach-tegra/include/mach/iomap.h | 3 +
arch/arm/mach-tegra/include/mach/lowlevel.h | 146 ++++++
arch/arm/mach-tegra/include/mach/tegra20-car.h | 179 +++++++
arch/arm/mach-tegra/include/mach/tegra20-pmc.h | 67 +++
arch/arm/mach-tegra/reset.c | 39 --
arch/arm/mach-tegra/tegra20-car.c | 120 +++++
arch/arm/mach-tegra/tegra20-pmc.c | 68 +++
arch/arm/mach-tegra/tegra20-timer.c | 119 +++++
arch/arm/mach-tegra/tegra20.c | 65 +++
arch/arm/mach-tegra/tegra_avp_init.c | 226 +++++++++
arch/arm/mach-tegra/tegra_maincomplex_init.c | 46 ++
arch/arm/mach-zynq/include/mach/clkdev.h | 6 -
arch/mips/boards/dlink-dir-320/config.h | 15 -
arch/mips/boards/qemu-malta/config.h | 15 -
arch/mips/boards/rzx50/config.h | 15 -
arch/sandbox/board/config.h | 4 -
arch/x86/boards/x86_generic/config.h | 17 -
arch/x86/include/asm/types.h | 4 +
commands/Kconfig | 54 ++-
commands/Makefile | 6 +
commands/bootm.c | 7 +-
commands/i2c.c | 2 +-
commands/md.c | 116 +++++
commands/mem.c | 526 +--------------------
commands/memcmp.c | 148 ++++++
commands/memcpy.c | 145 ++++++
commands/memset.c | 101 ++++
commands/mm.c | 117 +++++
commands/mw.c | 104 ++++
common/Makefile | 3 +
common/console.c | 26 +-
common/memory_display.c | 64 +++
defaultenv-2/base/bin/init | 12 +-
defaultenv-2/base/boot/net | 7 +-
defaultenv-2/menu/menu/settings | 2 +-
drivers/Kconfig | 1 +
drivers/Makefile | 1 +
drivers/amba/bus.c | 9 +-
drivers/ata/Kconfig | 1 -
drivers/ata/disk_ata_drive.c | 21 +-
drivers/base/driver.c | 3 +
drivers/gpio/Kconfig | 10 +
drivers/gpio/Makefile | 5 +-
.../arm/mach-imx/gpio.c => drivers/gpio/gpio-imx.c | 0
drivers/gpio/gpio-tegra.c | 214 +++++++++
drivers/gpio/{gpio.c => gpiolib.c} | 0
drivers/input/qt1070.c | 7 +-
drivers/mci/atmel_mci.c | 4 +-
drivers/mci/imx-esdhc.c | 7 -
drivers/mci/imx.c | 5 +-
drivers/mci/mci-core.c | 55 +--
drivers/mci/mxs.c | 22 +-
drivers/mtd/core.c | 13 +-
drivers/mtd/nand/nand_base.c | 421 +++++++++++------
drivers/mtd/nand/nand_ids.c | 4 +-
drivers/mtd/nand/nand_imx_bbm.c | 9 +-
drivers/net/ksz8864rmn.c | 30 +-
drivers/net/phy/mdio_bus.c | 8 +-
drivers/of/base.c | 133 +++++-
drivers/of/fdt.c | 3 +-
drivers/of/partition.c | 13 +-
drivers/pinctrl/Kconfig | 28 ++
drivers/pinctrl/Makefile | 4 +
.../iomux-v1.c => drivers/pinctrl/imx-iomux-v1.c | 0
.../iomux-v2.c => drivers/pinctrl/imx-iomux-v2.c | 0
drivers/pinctrl/imx-iomux-v3.c | 212 +++++++++
drivers/pinctrl/pinctrl.c | 149 ++++++
drivers/pwm/core.c | 89 ++--
drivers/usb/core/usb.c | 19 +-
drivers/usb/gadget/at91_udc.c | 23 +-
drivers/video/fb.c | 33 +-
drivers/video/imx-ipu-fb.c | 27 +-
drivers/video/imx.c | 26 +-
drivers/watchdog/im28wd.c | 75 ++-
include/asm-generic/gpio.h | 1 -
include/ata_drive.h | 1 +
include/common.h | 7 +-
include/console.h | 2 +
include/fb.h | 1 +
include/gpio.h | 2 +-
include/linux/mtd/bbm.h | 2 +
include/linux/mtd/mtd.h | 1 +
include/linux/mtd/nand.h | 20 +-
include/mci.h | 2 +
include/net.h | 7 +-
include/of.h | 10 +-
include/param.h | 66 ++-
include/pinctrl.h | 35 ++
include/usb/usb.h | 1 -
lib/copy_file.c | 2 -
lib/parameter.c | 302 ++++++++++--
net/dhcp.c | 15 +-
net/eth.c | 40 +-
net/net.c | 80 ++--
net/netconsole.c | 50 +-
scripts/Makefile.build | 2 +-
scripts/checkpatch.pl | 2 +-
230 files changed, 4445 insertions(+), 2516 deletions(-)
delete mode 100644 arch/arm/boards/archosg9/config.h
delete mode 100644 arch/arm/boards/avnet-zedboard/config.h
delete mode 100644 arch/arm/boards/beagle/config.h
delete mode 100644 arch/arm/boards/beaglebone/config.h
delete mode 100644 arch/arm/boards/ccxmx51/config.h
delete mode 100644 arch/arm/boards/chumby_falconwing/config.h
delete mode 100644 arch/arm/boards/clep7212/config.h
delete mode 100644 arch/arm/boards/crystalfontz-cfa10036/config.h
delete mode 100644 arch/arm/boards/dmo-mx6-realq7/config.h
delete mode 100644 arch/arm/boards/edb93xx/config.h
delete mode 100644 arch/arm/boards/efika-mx-smartbook/config.h
delete mode 100644 arch/arm/boards/eukrea_cpuimx27/config.h
delete mode 100644 arch/arm/boards/eukrea_cpuimx51/config.h
delete mode 100644 arch/arm/boards/freescale-mx23-evk/config.h
delete mode 100644 arch/arm/boards/freescale-mx28-evk/config.h
delete mode 100644 arch/arm/boards/freescale-mx51-pdk/config.h
delete mode 100644 arch/arm/boards/freescale-mx53-loco/config.h
delete mode 100644 arch/arm/boards/freescale-mx53-smd/config.h
delete mode 100644 arch/arm/boards/freescale-mx6-arm2/config.h
delete mode 100644 arch/arm/boards/freescale-mx6-sabrelite/config.h
delete mode 100644 arch/arm/boards/freescale-mx6-sabresd/config.h
delete mode 100644 arch/arm/boards/guf-neso/config.h
delete mode 100644 arch/arm/boards/guf-vincell/config.h
delete mode 100644 arch/arm/boards/highbank/config.h
create mode 120000 arch/arm/boards/highbank/env/boot.d/010-ahci-boot
create mode 120000 arch/arm/boards/highbank/env/boot.d/011-ahci
create mode 120000 arch/arm/boards/highbank/env/boot.d/020-mmc-boot
create mode 120000 arch/arm/boards/highbank/env/boot.d/021-mmc
create mode 120000 arch/arm/boards/highbank/env/boot.d/030-net
create mode 120000 arch/arm/boards/highbank/env/boot.d/031-net-eth1
create mode 100644 arch/arm/boards/highbank/env/boot/ahci
create mode 100644 arch/arm/boards/highbank/env/boot/ahci-boot
create mode 100644 arch/arm/boards/highbank/env/boot/mmc
create mode 100644 arch/arm/boards/highbank/env/boot/mmc-boot
create mode 100644 arch/arm/boards/highbank/env/boot/net
create mode 100644 arch/arm/boards/highbank/env/boot/net-eth1
delete mode 100644 arch/arm/boards/highbank/env/config
create mode 100644 arch/arm/boards/highbank/env/config-board
create mode 100644 arch/arm/boards/highbank/env/data/oftree
rename arch/arm/boards/highbank/env/{bin/init_board => init/001-dtb-probe} (100%)
create mode 100644 arch/arm/boards/highbank/env/init/automount
create mode 100644 arch/arm/boards/highbank/env/init/ps1
delete mode 100644 arch/arm/boards/imx21ads/config.h
delete mode 100644 arch/arm/boards/imx233-olinuxino/config.h
delete mode 100644 arch/arm/boards/imx27ads/config.h
delete mode 100644 arch/arm/boards/karo-tx28/config.h
delete mode 100644 arch/arm/boards/karo-tx51/config.h
delete mode 100644 arch/arm/boards/karo-tx53/config.h
delete mode 100644 arch/arm/boards/mioa701/config.h
delete mode 100644 arch/arm/boards/netx/config.h
delete mode 100644 arch/arm/boards/nhk8815/config.h
delete mode 100644 arch/arm/boards/omap343xdsp/config.h
delete mode 100644 arch/arm/boards/omap3evm/config.h
delete mode 100644 arch/arm/boards/panda/config.h
delete mode 100644 arch/arm/boards/pcm038/config.h
delete mode 100644 arch/arm/boards/pcm049/config.h
delete mode 100644 arch/arm/boards/pcm051/config.h
delete mode 100644 arch/arm/boards/phycard-a-l1/config.h
delete mode 100644 arch/arm/boards/phycard-a-xl2/config.h
delete mode 100644 arch/arm/boards/phycard-i.MX27/config.h
delete mode 100644 arch/arm/boards/raspberry-pi/config.h
delete mode 100644 arch/arm/boards/toshiba-ac100/config.h
delete mode 100644 arch/arm/boards/toshiba-ac100/lowlevel.c
delete mode 100644 arch/arm/boards/toshiba-ac100/serial.c
delete mode 100644 arch/arm/boards/tqma53/config.h
delete mode 100644 arch/arm/boards/versatile/config.h
delete mode 100644 arch/arm/boards/vexpress/config.h
create mode 100644 arch/arm/dts/tegra20-paz00.dts
create mode 100644 arch/arm/dts/tegra20.dtsi
delete mode 100644 arch/arm/mach-imx/iomux-v3.c
create mode 100644 arch/arm/mach-omap/boot_order.c
delete mode 100644 arch/arm/mach-tegra/clock.c
create mode 100644 arch/arm/mach-tegra/include/mach/gpio.h
create mode 100644 arch/arm/mach-tegra/include/mach/lowlevel.h
create mode 100644 arch/arm/mach-tegra/include/mach/tegra20-car.h
create mode 100644 arch/arm/mach-tegra/include/mach/tegra20-pmc.h
delete mode 100644 arch/arm/mach-tegra/reset.c
create mode 100644 arch/arm/mach-tegra/tegra20-car.c
create mode 100644 arch/arm/mach-tegra/tegra20-pmc.c
create mode 100644 arch/arm/mach-tegra/tegra20-timer.c
create mode 100644 arch/arm/mach-tegra/tegra20.c
create mode 100644 arch/arm/mach-tegra/tegra_avp_init.c
create mode 100644 arch/arm/mach-tegra/tegra_maincomplex_init.c
delete mode 100644 arch/arm/mach-zynq/include/mach/clkdev.h
delete mode 100644 arch/mips/boards/dlink-dir-320/config.h
delete mode 100644 arch/mips/boards/qemu-malta/config.h
delete mode 100644 arch/mips/boards/rzx50/config.h
delete mode 100644 arch/sandbox/board/config.h
delete mode 100644 arch/x86/boards/x86_generic/config.h
create mode 100644 commands/md.c
create mode 100644 commands/memcmp.c
create mode 100644 commands/memcpy.c
create mode 100644 commands/memset.c
create mode 100644 commands/mm.c
create mode 100644 commands/mw.c
create mode 100644 common/memory_display.c
rename arch/arm/mach-imx/gpio.c => drivers/gpio/gpio-imx.c (100%)
create mode 100644 drivers/gpio/gpio-tegra.c
rename drivers/gpio/{gpio.c => gpiolib.c} (100%)
create mode 100644 drivers/pinctrl/Kconfig
create mode 100644 drivers/pinctrl/Makefile
rename arch/arm/mach-imx/iomux-v1.c => drivers/pinctrl/imx-iomux-v1.c (100%)
rename arch/arm/mach-imx/iomux-v2.c => drivers/pinctrl/imx-iomux-v2.c (100%)
create mode 100644 drivers/pinctrl/imx-iomux-v3.c
create mode 100644 drivers/pinctrl/pinctrl.c
create mode 100644 include/pinctrl.h
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2013-06-03 7:33 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-06-03 7:33 v2013.06.0 Sascha Hauer
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox