mail archive of the barebox mailing list
 help / color / mirror / Atom feed
* i.MX25 : Ethernet link detection blocking console
@ 2014-02-21 16:22 Eric Bénard
  2014-02-24  8:27 ` Sascha Hauer
  0 siblings, 1 reply; 2+ messages in thread
From: Eric Bénard @ 2014-02-21 16:22 UTC (permalink / raw)
  To: barebox

Hi,

while testing 2014.02 on eukrea-cpuimx25 board, I meet this problem :
- I get "Hit any key to stop autoboot:  1"
- whatever I press on the keyboard, the autoboot continues
- if I send characters through the serial port before barebox reach
  the autoboot line, then I'll get the command line but only when the
  link detection will have finished (check log below).

Any idea what could be wrong here ?

Thanks
Eric

barebox 2014.02.0-dirty #5 Fri Feb 21 16:52:37 CET 2014


Board: Eukrea CPUIMX25
netconsole: registered as cs1
mdio_bus: miibus0: probed
nand: ONFI param page 0 valid
nand: ONFI flash detected
nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0x38 (Micron
MT29F8G08ABABAWP), 1024MiB, page size: 4096, OOB size: 224
Bad block table found at page 262016, version 0x01
Bad block table found at page 261888, version 0x01
imxfb imxfb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space: 0x83700000 -> 0x83efffff (size 8 MiB)
running /env/bin/init...

Hit any key to stop autoboot:  1100Mbps full duplex link detected
                                ^ it waits here until the link is
                                detected then I get the prompt (only if
                                the key was pressed before reaching the
                                autoboot line)

barebox@Eukrea CPUIMX25:/ <INTERRUPT>

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

^ permalink raw reply	[flat|nested] 2+ messages in thread

* Re: i.MX25 : Ethernet link detection blocking console
  2014-02-21 16:22 i.MX25 : Ethernet link detection blocking console Eric Bénard
@ 2014-02-24  8:27 ` Sascha Hauer
  0 siblings, 0 replies; 2+ messages in thread
From: Sascha Hauer @ 2014-02-24  8:27 UTC (permalink / raw)
  To: Eric Bénard; +Cc: barebox

Hi Eric,

On Fri, Feb 21, 2014 at 05:22:09PM +0100, Eric Bénard wrote:
> Hi,
> 
> while testing 2014.02 on eukrea-cpuimx25 board, I meet this problem :
> - I get "Hit any key to stop autoboot:  1"
> - whatever I press on the keyboard, the autoboot continues
> - if I send characters through the serial port before barebox reach
>   the autoboot line, then I'll get the command line but only when the
>   link detection will have finished (check log below).
> 
> Any idea what could be wrong here ?

I have no idea. Does this happen with the defconfig currently in the
repository?

The only thing I could think of is that some kind of automount triggers,
but the cpuimx25 doesn't use automounts. Another possibility might be
the network console, but this should normally not even start without
being configured. Could you disable netconsole?

Sascha

> 
> Thanks
> Eric
> 
> barebox 2014.02.0-dirty #5 Fri Feb 21 16:52:37 CET 2014
> 
> 
> Board: Eukrea CPUIMX25
> netconsole: registered as cs1
> mdio_bus: miibus0: probed
> nand: ONFI param page 0 valid
> nand: ONFI flash detected
> nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0x38 (Micron
> MT29F8G08ABABAWP), 1024MiB, page size: 4096, OOB size: 224
> Bad block table found at page 262016, version 0x01
> Bad block table found at page 261888, version 0x01
> imxfb imxfb: i.MX Framebuffer driver
> imx-esdhc imx-esdhc0: registered as imx-esdhc0
> ehci ehci0: USB EHCI 1.00
> malloc space: 0x83700000 -> 0x83efffff (size 8 MiB)
> running /env/bin/init...
> 
> Hit any key to stop autoboot:  1100Mbps full duplex link detected
>                                 ^ it waits here until the link is
>                                 detected then I get the prompt (only if
>                                 the key was pressed before reaching the
>                                 autoboot line)
> 
> barebox@Eukrea CPUIMX25:/ <INTERRUPT>
> 
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
> 

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

^ permalink raw reply	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2014-02-24  8:27 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-02-21 16:22 i.MX25 : Ethernet link detection blocking console Eric Bénard
2014-02-24  8:27 ` Sascha Hauer

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox