From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from metis.ext.pengutronix.de ([2001:6f8:1178:4:290:27ff:fe1d:cc33]) by merlin.infradead.org with esmtps (Exim 4.80.1 #2 (Red Hat Linux)) id 1WJ7hj-0002Zy-HM for barebox@lists.infradead.org; Thu, 27 Feb 2014 20:37:16 +0000 Date: Thu, 27 Feb 2014 21:36:52 +0100 From: Sascha Hauer Message-ID: <20140227203652.GS17250@pengutronix.de> References: <1393509826-19549-1-git-send-email-philippe.retornaz@epfl.ch> <1393509826-19549-2-git-send-email-philippe.retornaz@epfl.ch> MIME-Version: 1.0 Content-Disposition: inline In-Reply-To: <1393509826-19549-2-git-send-email-philippe.retornaz@epfl.ch> List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: text/plain; charset="iso-8859-15" Content-Transfer-Encoding: quoted-printable Sender: "barebox" Errors-To: barebox-bounces+u.kleine-koenig=pengutronix.de@lists.infradead.org Subject: Re: [PATCH 1/1] ARM: i.MX31: Add support for mx31moboard board To: Philippe =?iso-8859-15?Q?R=E9tornaz?= Cc: barebox@lists.infradead.org Looks mostly good, some remarks inline. On Thu, Feb 27, 2014 at 03:03:45PM +0100, Philippe R=E9tornaz wrote: > +lwl-y +=3D lowlevel.o > +obj-y +=3D mx31moboard.o > diff --git a/arch/arm/boards/mx31moboard/env/boot/net b/arch/arm/boards/m= x31moboard/env/boot/net > new file mode 100644 > index 0000000..e81f2cd > --- /dev/null > +++ b/arch/arm/boards/mx31moboard/env/boot/net > @@ -0,0 +1,3 @@ > +#!/bin/sh > + > +# No network card support on this board Are you sure you want to drop this? You could attach a USB ethernet dongle. > diff --git a/arch/arm/boards/mx31moboard/env/boot/sd b/arch/arm/boards/mx= 31moboard/env/boot/sd > new file mode 100644 > index 0000000..f96633f > --- /dev/null > +++ b/arch/arm/boards/mx31moboard/env/boot/sd > @@ -0,0 +1,18 @@ > +#!/bin/sh > + > +if [ "$1" =3D menu ]; then > + boot-menu-add-entry "$0" "SD Boot" > + exit > +fi > + > +global.bootm.image=3D/mnt/sd/boot/zImage > + > +if [ -e /mnt/sd/boot/oftree ]; then > + global.bootm.oftree=3D/mnt/sd/boot/oftree > +fi > + > +if [ -e /mnt/sd/boot/initrd.img ]; then > + global.bootm.initrd=3D/mnt/sd/boot/initrd.img > +fi > + > +global.linux.bootargs.dyn.root=3D"root=3D/dev/mmcblk0p1 rootwait" Consider using bootloader spec entries, see http://www.freedesktop.org/wiki/Specifications/BootLoaderSpec/ Basically you put a config file under /loader/entries/ in your rootfs. The config file describes where your kernel/initrd/oftree is. Under barebox you just have to 'boot mci0' without further configuration. > +void __bare_init __naked barebox_arm_reset_vector(void) > +{ > + uint32_t r; > + > + arm_cpu_lowlevel_init(); > + > + /* Enable IPU Display interface */ > + writel(1 << 6, MX31_IPU_CTRL_BASE_ADDR); > + > + writel(0x074B0BF5, MX31_CCM_BASE_ADDR + MX31_CCM_CCMR); > + > + asm volatile("1:\n\t" > + "SUBS %0, %0, #1 \n\t" > + "BNE 1b \n\t" > + : : "r" (0x4000) : "cc"); You can write a delay loop in c with: volatile int c; for (c =3D 0; c < 0x4000; c++) (the volatile prevents the compiler from optimizing the loop away) > +#include > +#include > +#include > +#include > +#include > + > +#ifdef CONFIG_USB > +#define USBH2_EN_B IOMUX_TO_GPIO(MX31_PIN_SCK6) > +#define USB_RESET_B IOMUX_TO_GPIO(MX31_PIN_GPIO1_0) > + > +static void mx31moboard_usb_init(void) > +{ > + u32 tmp; > + Instead of ifdeffing the code you can write: if (!IS_ENABLED(CONFIG_USB)) return; The compiler is clever enough to optimize the unused code away, still you get better compile coverage. > +static void mx31moboard_add_leds(void) > +{ > + int i; > + Same here: if (!IS_ENABLED(CONFIG_LED_GPIO)) return; Sascha -- = Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox