* [RFC v2 2/2] [WIP] net: add initial ENC28J60 support
2014-06-16 7:41 [RFC v2 1/2] [WIP] net.h: add ETH_ALEN constant; fix whitespaces Antony Pavlov
@ 2014-06-16 7:41 ` Antony Pavlov
2014-06-23 6:33 ` Sascha Hauer
0 siblings, 1 reply; 3+ messages in thread
From: Antony Pavlov @ 2014-06-16 7:41 UTC (permalink / raw)
To: barebox
ENC28J60 is a stand-alone Ethernet controller with SPI Interface.
and integrated 10BASE-T PHY.
This driver was ported from linux-3.15.
The most notable barebox driver version changes:
* add device tree support;
* use IF_ENABLED for checking CONFIG_ENC28J60_WRITEVERIFY;
* add mii_bus support;
* rename {nolock,locked}_regw_{read,write}() to enc28j60_*_{read,write}().
TODOs:
* receive only one packet per enc28j60_eth_rx() call.
* fix empty enc28j60_init_dev;
* add parameter for changing debug loglevel on-the-run;
* ENC28J60 supports only SPI mode 0 so we have to submit
this information to the SPI controller explicitly.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Changes since v1:
* drop unused macros;
* use random_ether_addr();
* drop 'select CRC32' in Kconfig;
* drop MAC address generation in driver's code;
* rename {nolock,locked}_regw_{read,write}() to enc28j60_*_{read,write}();
* add mii_bus support.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
---
drivers/net/Kconfig | 14 +
drivers/net/Makefile | 1 +
drivers/net/enc28j60.c | 1057 +++++++++++++++++++++++++++++++++++++++++++++
drivers/net/enc28j60_hw.h | 307 +++++++++++++
include/linux/netdevice.h | 53 +++
5 files changed, 1432 insertions(+)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 7a0d5e1..5daf7ff 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -73,6 +73,20 @@ config DRIVER_NET_DM9K
depends on HAS_DM9000
select PHYLIB
+config DRIVER_NET_ENC28J60
+ bool "ENC28J60 support"
+ depends on SPI
+ select PHYLIB
+ ---help---
+ Support for the Microchip EN28J60 ethernet chip.
+
+config DRIVER_NET_ENC28J60_WRITEVERIFY
+ bool "Enable write verify"
+ depends on DRIVER_NET_ENC28J60
+ ---help---
+ Enable the verify after the buffer write useful for debugging purpose.
+ If unsure, say N.
+
config DRIVER_NET_EP93XX
bool "EP93xx Ethernet driver"
depends on ARCH_EP93XX
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 65f0d8b..8acd2a6 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_DRIVER_NET_CPSW) += cpsw.o
obj-$(CONFIG_DRIVER_NET_DAVINCI_EMAC) += davinci_emac.o
obj-$(CONFIG_DRIVER_NET_DESIGNWARE) += designware.o
obj-$(CONFIG_DRIVER_NET_DM9K) += dm9k.o
+obj-$(CONFIG_DRIVER_NET_ENC28J60) += enc28j60.o
obj-$(CONFIG_DRIVER_NET_EP93XX) += ep93xx.o
obj-$(CONFIG_DRIVER_NET_ETHOC) += ethoc.o
obj-$(CONFIG_DRIVER_NET_FEC_IMX) += fec_imx.o
diff --git a/drivers/net/enc28j60.c b/drivers/net/enc28j60.c
new file mode 100644
index 0000000..99eb608
--- /dev/null
+++ b/drivers/net/enc28j60.c
@@ -0,0 +1,1057 @@
+/*
+ * Microchip ENC28J60 ethernet driver (MAC + PHY)
+ *
+ * This code was ported from linux-3.15 kernel by Antony Pavlov.
+ *
+ * Copyright (C) 2007 Eurek srl
+ * Author: Claudio Lanconelli <lanconelli.claudio@eptar.com>
+ * based on enc28j60.c written by David Anders for 2.4 kernel version
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+
+#include <common.h>
+#include <net.h>
+#include <malloc.h>
+#include <init.h>
+#include <driver.h>
+#include <spi/spi.h>
+#include <xfuncs.h>
+#include <errno.h>
+#include <linux/netdevice.h>
+
+#include "enc28j60_hw.h"
+
+#define DRV_NAME "enc28j60"
+
+#define SPI_OPLEN 1
+
+#define ENC28J60_MSG_DEFAULT \
+ (NETIF_MSG_PROBE | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN | NETIF_MSG_LINK)
+
+/* Buffer size required for the largest SPI transfer (i.e., reading a
+ * frame). */
+#define SPI_TRANSFER_BUF_LEN (4 + MAX_FRAMELEN)
+
+/* Driver local data */
+struct enc28j60_net {
+ struct eth_device edev;
+ struct spi_device *spi;
+ u8 bank; /* current register bank selected */
+ u16 next_pk_ptr; /* next packet pointer within FIFO */
+ u16 max_pk_counter; /* statistics: max packet counter */
+ u16 tx_retry_count;
+ bool hw_enable;
+ bool full_duplex;
+ int rxfilter;
+ u32 msg_enable;
+ u8 spi_transfer_buf[SPI_TRANSFER_BUF_LEN];
+ /* store MAC address here while hardware is in the reset state */
+ u8 hwaddr[ETH_ALEN];
+ struct mii_bus miibus;
+};
+
+/*
+ * SPI read buffer
+ * wait for the SPI transfer and copy received data to destination
+ */
+static int
+spi_read_buf(struct enc28j60_net *priv, int len, u8 *data)
+{
+ u8 *rx_buf = priv->spi_transfer_buf + 4;
+ u8 *tx_buf = priv->spi_transfer_buf;
+ struct spi_transfer t = {
+ .tx_buf = tx_buf,
+ .rx_buf = rx_buf,
+ .len = SPI_OPLEN + len,
+ };
+ struct spi_message msg;
+ int ret;
+
+ tx_buf[0] = ENC28J60_READ_BUF_MEM;
+ tx_buf[1] = tx_buf[2] = tx_buf[3] = 0; /* don't care */
+
+ spi_message_init(&msg);
+ spi_message_add_tail(&t, &msg);
+ ret = spi_sync(priv->spi, &msg);
+ if (ret == 0) {
+ memcpy(data, &rx_buf[SPI_OPLEN], len);
+ ret = msg.status;
+ }
+ if (ret && netif_msg_drv(priv))
+ dev_dbg(&priv->edev.dev,
+ "%s() failed: ret = %d\n", __func__, ret);
+
+ return ret;
+}
+
+/*
+ * SPI write buffer
+ */
+static int spi_write_buf(struct enc28j60_net *priv, int len,
+ const u8 *data)
+{
+ int ret;
+
+ if (len > SPI_TRANSFER_BUF_LEN - 1 || len <= 0)
+ ret = -EINVAL;
+ else {
+ priv->spi_transfer_buf[0] = ENC28J60_WRITE_BUF_MEM;
+ memcpy(&priv->spi_transfer_buf[1], data, len);
+ ret = spi_write(priv->spi, priv->spi_transfer_buf, len + 1);
+ if (ret && netif_msg_drv(priv))
+ dev_dbg(&priv->edev.dev,
+ "%s() failed: ret = %d\n", __func__, ret);
+ }
+ return ret;
+}
+
+/*
+ * basic SPI read operation
+ */
+static u8 spi_read_op(struct enc28j60_net *priv, u8 op,
+ u8 addr)
+{
+ u8 tx_buf[2];
+ u8 rx_buf[4];
+ u8 val = 0;
+ int ret;
+ int slen = SPI_OPLEN;
+
+ /* do dummy read if needed */
+ if (addr & SPRD_MASK)
+ slen++;
+
+ tx_buf[0] = op | (addr & ADDR_MASK);
+ ret = spi_write_then_read(priv->spi, tx_buf, 1, rx_buf, slen);
+ if (ret)
+ dev_dbg(&priv->edev.dev,
+ "%s() failed: ret = %d\n", __func__, ret);
+ else
+ val = rx_buf[slen - 1];
+
+ return val;
+}
+
+/*
+ * basic SPI write operation
+ */
+static int spi_write_op(struct enc28j60_net *priv, u8 op,
+ u8 addr, u8 val)
+{
+ int ret;
+
+ priv->spi_transfer_buf[0] = op | (addr & ADDR_MASK);
+ priv->spi_transfer_buf[1] = val;
+ ret = spi_write(priv->spi, priv->spi_transfer_buf, 2);
+ if (ret && netif_msg_drv(priv))
+ dev_dbg(&priv->edev.dev,
+ "%s() failed: ret = %d\n", __func__, ret);
+
+ return ret;
+}
+
+static void enc28j60_soft_reset(struct enc28j60_net *priv)
+{
+ if (netif_msg_hw(priv))
+ dev_dbg(&priv->edev.dev, "%s() enter\n", __func__);
+
+ spi_write_op(priv, ENC28J60_SOFT_RESET, 0, ENC28J60_SOFT_RESET);
+ /* Errata workaround #1, CLKRDY check is unreliable,
+ * delay at least 1 mS instead */
+ udelay(2000);
+}
+
+/*
+ * select the current register bank if necessary
+ */
+static void enc28j60_set_bank(struct enc28j60_net *priv, u8 addr)
+{
+ u8 b = (addr & BANK_MASK) >> 5;
+
+ /* These registers (EIE, EIR, ESTAT, ECON2, ECON1)
+ * are present in all banks, no need to switch bank
+ */
+ if (addr >= EIE && addr <= ECON1)
+ return;
+
+ /* Clear or set each bank selection bit as needed */
+ if ((b & ECON1_BSEL0) != (priv->bank & ECON1_BSEL0)) {
+ if (b & ECON1_BSEL0)
+ spi_write_op(priv, ENC28J60_BIT_FIELD_SET, ECON1,
+ ECON1_BSEL0);
+ else
+ spi_write_op(priv, ENC28J60_BIT_FIELD_CLR, ECON1,
+ ECON1_BSEL0);
+ }
+ if ((b & ECON1_BSEL1) != (priv->bank & ECON1_BSEL1)) {
+ if (b & ECON1_BSEL1)
+ spi_write_op(priv, ENC28J60_BIT_FIELD_SET, ECON1,
+ ECON1_BSEL1);
+ else
+ spi_write_op(priv, ENC28J60_BIT_FIELD_CLR, ECON1,
+ ECON1_BSEL1);
+ }
+ priv->bank = b;
+}
+
+/*
+ * Register access routines through the SPI bus.
+ * Some registers can be accessed through the bit field clear and
+ * bit field set to avoid a read modify write cycle.
+ */
+
+/*
+ * Register bit field Set
+ */
+static void enc28j60_reg_bfset(struct enc28j60_net *priv,
+ u8 addr, u8 mask)
+{
+ enc28j60_set_bank(priv, addr);
+ spi_write_op(priv, ENC28J60_BIT_FIELD_SET, addr, mask);
+}
+
+/*
+ * Register bit field Clear
+ */
+static void enc28j60_reg_bfclr(struct enc28j60_net *priv,
+ u8 addr, u8 mask)
+{
+ enc28j60_set_bank(priv, addr);
+ spi_write_op(priv, ENC28J60_BIT_FIELD_CLR, addr, mask);
+}
+
+/*
+ * Register byte read
+ */
+static int enc28j60_regb_read(struct enc28j60_net *priv,
+ u8 address)
+{
+ enc28j60_set_bank(priv, address);
+ return spi_read_op(priv, ENC28J60_READ_CTRL_REG, address);
+}
+
+/*
+ * Register word read
+ */
+static int enc28j60_regw_read(struct enc28j60_net *priv,
+ u8 address)
+{
+ int rl, rh;
+
+ enc28j60_set_bank(priv, address);
+ rl = spi_read_op(priv, ENC28J60_READ_CTRL_REG, address);
+ rh = spi_read_op(priv, ENC28J60_READ_CTRL_REG, address + 1);
+
+ return (rh << 8) | rl;
+}
+
+/*
+ * Register byte write
+ */
+static void enc28j60_regb_write(struct enc28j60_net *priv,
+ u8 address, u8 data)
+{
+ enc28j60_set_bank(priv, address);
+ spi_write_op(priv, ENC28J60_WRITE_CTRL_REG, address, data);
+}
+
+/*
+ * Register word write
+ */
+static void enc28j60_regw_write(struct enc28j60_net *priv,
+ u8 address, u16 data)
+{
+ enc28j60_set_bank(priv, address);
+ spi_write_op(priv, ENC28J60_WRITE_CTRL_REG, address, (u8) data);
+ spi_write_op(priv, ENC28J60_WRITE_CTRL_REG, address + 1,
+ (u8) (data >> 8));
+}
+
+/*
+ * Buffer memory read
+ * Select the starting address and execute a SPI buffer read
+ */
+static void enc28j60_mem_read(struct enc28j60_net *priv,
+ u16 addr, int len, u8 *data)
+{
+ enc28j60_regw_write(priv, ERDPTL, addr);
+
+ if (IS_ENABLED(CONFIG_ENC28J60_WRITEVERIFY) && netif_msg_drv(priv)) {
+ u16 reg;
+ reg = enc28j60_regw_read(priv, ERDPTL);
+ if (reg != addr)
+ dev_dbg(&priv->edev.dev, "%s() error writing ERDPT "
+ "(0x%04x - 0x%04x)\n", __func__, reg, addr);
+ }
+
+ spi_read_buf(priv, len, data);
+}
+
+/*
+ * Write packet to enc28j60 TX buffer memory
+ */
+static void
+enc28j60_packet_write(struct enc28j60_net *priv, int len, const u8 *data)
+{
+ /* Set the write pointer to start of transmit buffer area */
+ enc28j60_regw_write(priv, EWRPTL, TXSTART_INIT);
+
+ if (IS_ENABLED(CONFIG_ENC28J60_WRITEVERIFY) && netif_msg_drv(priv)) {
+ u16 reg;
+ reg = enc28j60_regw_read(priv, EWRPTL);
+ if (reg != TXSTART_INIT)
+ dev_dbg(&priv->edev.dev,
+ "%s() ERWPT:0x%04x != 0x%04x\n",
+ __func__, reg, TXSTART_INIT);
+ }
+ /* Set the TXND pointer to correspond to the packet size given */
+ enc28j60_regw_write(priv, ETXNDL, TXSTART_INIT + len);
+ /* write per-packet control byte */
+ spi_write_op(priv, ENC28J60_WRITE_BUF_MEM, 0, 0x00);
+ if (netif_msg_hw(priv))
+ dev_dbg(&priv->edev.dev,
+ "%s() after control byte ERWPT:0x%04x\n",
+ __func__, enc28j60_regw_read(priv, EWRPTL));
+ /* copy the packet into the transmit buffer */
+ spi_write_buf(priv, len, data);
+ if (netif_msg_hw(priv))
+ dev_dbg(&priv->edev.dev,
+ "%s() after write packet ERWPT:0x%04x, len=%d\n",
+ __func__, enc28j60_regw_read(priv, EWRPTL), len);
+}
+
+static int poll_ready(struct enc28j60_net *priv, u8 reg, u8 mask, u8 val)
+{
+ if ((enc28j60_regb_read(priv, reg) & mask) == val) {
+ return 0;
+ }
+
+ /* 20 msec timeout read */
+ mdelay(20);
+
+ if ((enc28j60_regb_read(priv, reg) & mask) != val) {
+ dev_dbg(&priv->spi->dev,
+ "reg %02x ready timeout!\n", reg);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+/*
+ * Wait until the PHY operation is complete.
+ */
+static int wait_phy_ready(struct enc28j60_net *priv)
+{
+ return poll_ready(priv, MISTAT, MISTAT_BUSY, 0) ? 0 : 1;
+}
+
+/*
+ * PHY register read
+ * PHY registers are not accessed directly, but through the MII
+ */
+static u16 enc28j60_phy_read(struct enc28j60_net *priv, u8 address)
+{
+ u16 ret;
+
+ /* set the PHY register address */
+ enc28j60_regb_write(priv, MIREGADR, address);
+ /* start the register read operation */
+ enc28j60_regb_write(priv, MICMD, MICMD_MIIRD);
+ /* wait until the PHY read completes */
+ wait_phy_ready(priv);
+ /* quit reading */
+ enc28j60_regb_write(priv, MICMD, 0x00);
+ /* return the data */
+ ret = enc28j60_regw_read(priv, MIRDL);
+
+ return ret;
+}
+
+static int enc28j60_phy_write(struct enc28j60_net *priv, u8 address, u16 data)
+{
+ int ret;
+
+ /* set the PHY register address */
+ enc28j60_regb_write(priv, MIREGADR, address);
+ /* write the PHY data */
+ enc28j60_regw_write(priv, MIWRL, data);
+ /* wait until the PHY write completes and return */
+ ret = wait_phy_ready(priv);
+
+ return ret;
+}
+
+/*
+ * MII-interface related functions
+ */
+static int enc28j60_miibus_read(struct mii_bus *bus, int phy_addr, int reg_addr)
+{
+ struct enc28j60_net *priv = (struct enc28j60_net *)bus->priv;
+
+ if (phy_addr == 0) {
+ return enc28j60_phy_read(priv, reg_addr);
+ }
+
+ return 0xffff;
+}
+
+static int enc28j60_miibus_write(struct mii_bus *bus, int phy_addr,
+ int reg_addr, u16 data)
+{
+ struct enc28j60_net *priv = (struct enc28j60_net *)bus->priv;
+
+ if (phy_addr == 0) {
+ enc28j60_phy_write(priv, reg_addr, data);
+ }
+
+ return 0;
+}
+
+static int enc28j60_get_ethaddr(struct eth_device *edev, unsigned char *m)
+{
+ struct enc28j60_net *priv = edev->priv;
+
+ memcpy(m, priv->hwaddr, ETH_ALEN);
+
+ if (netif_msg_drv(priv))
+ dev_err(&edev->dev, "getting MAC address\n");
+
+ return 0;
+}
+
+/*
+ * Program the hardware MAC address from dev->dev_addr.
+ */
+static int enc28j60_set_ethaddr(struct eth_device *edev,
+ unsigned char *mac_addr)
+{
+ int ret;
+ struct enc28j60_net *priv = edev->priv;
+
+ if (!priv->hw_enable) {
+ if (netif_msg_drv(priv))
+ dev_err(&edev->dev,
+ "%s(): Setting MAC address\n", __func__);
+ /* NOTE: MAC address in ENC28J60 is byte-backward */
+ enc28j60_regb_write(priv, MAADR5, mac_addr[0]);
+ enc28j60_regb_write(priv, MAADR4, mac_addr[1]);
+ enc28j60_regb_write(priv, MAADR3, mac_addr[2]);
+ enc28j60_regb_write(priv, MAADR2, mac_addr[3]);
+ enc28j60_regb_write(priv, MAADR1, mac_addr[4]);
+ enc28j60_regb_write(priv, MAADR0, mac_addr[5]);
+ ret = 0;
+ memcpy(priv->hwaddr, mac_addr, ETH_ALEN);
+ } else {
+ if (netif_msg_drv(priv))
+ dev_dbg(&edev->dev,
+ "%s() Hardware must be disabled to set "
+ "Mac address\n", __func__);
+ ret = -EBUSY;
+ }
+
+ return ret;
+}
+
+/*
+ * Debug routine to dump useful register contents
+ */
+static void enc28j60_dump_regs(struct enc28j60_net *priv, const char *msg)
+{
+ dev_dbg(&priv->edev.dev, " %s\n"
+ "HwRevID: 0x%02x\n"
+ "Cntrl: ECON1 ECON2 ESTAT EIR EIE\n"
+ " 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x\n"
+ "MAC : MACON1 MACON3 MACON4\n"
+ " 0x%02x 0x%02x 0x%02x\n"
+ "Rx : ERXST ERXND ERXWRPT ERXRDPT ERXFCON EPKTCNT MAMXFL\n"
+ " 0x%04x 0x%04x 0x%04x 0x%04x "
+ "0x%02x 0x%02x 0x%04x\n"
+ "Tx : ETXST ETXND MACLCON1 MACLCON2 MAPHSUP\n"
+ " 0x%04x 0x%04x 0x%02x 0x%02x 0x%02x\n",
+ msg, enc28j60_regb_read(priv, EREVID),
+ enc28j60_regb_read(priv, ECON1), enc28j60_regb_read(priv, ECON2),
+ enc28j60_regb_read(priv, ESTAT), enc28j60_regb_read(priv, EIR),
+ enc28j60_regb_read(priv, EIE), enc28j60_regb_read(priv, MACON1),
+ enc28j60_regb_read(priv, MACON3), enc28j60_regb_read(priv, MACON4),
+ enc28j60_regw_read(priv, ERXSTL), enc28j60_regw_read(priv, ERXNDL),
+ enc28j60_regw_read(priv, ERXWRPTL),
+ enc28j60_regw_read(priv, ERXRDPTL),
+ enc28j60_regb_read(priv, ERXFCON),
+ enc28j60_regb_read(priv, EPKTCNT),
+ enc28j60_regw_read(priv, MAMXFLL), enc28j60_regw_read(priv, ETXSTL),
+ enc28j60_regw_read(priv, ETXNDL),
+ enc28j60_regb_read(priv, MACLCON1),
+ enc28j60_regb_read(priv, MACLCON2),
+ enc28j60_regb_read(priv, MAPHSUP));
+}
+
+/*
+ * ERXRDPT need to be set always at odd addresses, refer to errata datasheet
+ */
+static u16 erxrdpt_workaround(u16 next_packet_ptr, u16 start, u16 end)
+{
+ u16 erxrdpt;
+
+ if ((next_packet_ptr - 1 < start) || (next_packet_ptr - 1 > end))
+ erxrdpt = end;
+ else
+ erxrdpt = next_packet_ptr - 1;
+
+ return erxrdpt;
+}
+
+/*
+ * Calculate wrap around when reading beyond the end of the RX buffer
+ */
+static u16 rx_packet_start(u16 ptr)
+{
+ if (ptr + RSV_SIZE > RXEND_INIT)
+ return (ptr + RSV_SIZE) - (RXEND_INIT - RXSTART_INIT + 1);
+ else
+ return ptr + RSV_SIZE;
+}
+
+static void enc28j60_rxfifo_init(struct enc28j60_net *priv, u16 start, u16 end)
+{
+ u16 erxrdpt;
+
+ if (start > 0x1FFF || end > 0x1FFF || start > end) {
+ if (netif_msg_drv(priv))
+ dev_err(&priv->edev.dev,
+ "%s(%d, %d) RXFIFO bad parameters!\n",
+ __func__, start, end);
+ return;
+ }
+
+ /* set receive buffer start + end */
+ priv->next_pk_ptr = start;
+ enc28j60_regw_write(priv, ERXSTL, start);
+ erxrdpt = erxrdpt_workaround(priv->next_pk_ptr, start, end);
+ enc28j60_regw_write(priv, ERXRDPTL, erxrdpt);
+ enc28j60_regw_write(priv, ERXNDL, end);
+}
+
+static void enc28j60_txfifo_init(struct enc28j60_net *priv, u16 start, u16 end)
+{
+ if (start > 0x1FFF || end > 0x1FFF || start > end) {
+ if (netif_msg_drv(priv))
+ dev_err(&priv->edev.dev,
+ "%s(%d, %d) TXFIFO bad parameters!\n",
+ __func__, start, end);
+ return;
+ }
+ /* set transmit buffer start + end */
+ enc28j60_regw_write(priv, ETXSTL, start);
+ enc28j60_regw_write(priv, ETXNDL, end);
+}
+
+/*
+ * Low power mode shrinks power consumption about 100x, so we'd like
+ * the chip to be in that mode whenever it's inactive. (However, we
+ * can't stay in lowpower mode during suspend with WOL active.)
+ */
+static void enc28j60_lowpower(struct enc28j60_net *priv, bool is_low)
+{
+ if (netif_msg_drv(priv))
+ dev_dbg(&priv->spi->dev, "%s power...\n",
+ is_low ? "low" : "high");
+
+ if (is_low) {
+ enc28j60_reg_bfclr(priv, ECON1, ECON1_RXEN);
+ poll_ready(priv, ESTAT, ESTAT_RXBUSY, 0);
+ poll_ready(priv, ECON1, ECON1_TXRTS, 0);
+ /* ECON2_VRPS was set during initialization */
+ enc28j60_reg_bfset(priv, ECON2, ECON2_PWRSV);
+ } else {
+ enc28j60_reg_bfclr(priv, ECON2, ECON2_PWRSV);
+ poll_ready(priv, ESTAT, ESTAT_CLKRDY, ESTAT_CLKRDY);
+ /* caller sets ECON1_RXEN */
+ }
+}
+
+static int enc28j60_hw_init(struct enc28j60_net *priv)
+{
+ u8 reg;
+
+ if (netif_msg_drv(priv))
+ dev_dbg(&priv->edev.dev, "%s() - %s\n", __func__,
+ priv->full_duplex ? "FullDuplex" : "HalfDuplex");
+
+ /* first reset the chip */
+ enc28j60_soft_reset(priv);
+ /* Clear ECON1 */
+ spi_write_op(priv, ENC28J60_WRITE_CTRL_REG, ECON1, 0x00);
+ priv->bank = 0;
+ priv->hw_enable = false;
+ priv->tx_retry_count = 0;
+ priv->max_pk_counter = 0;
+
+ /* enable address auto increment and voltage regulator powersave */
+ enc28j60_regb_write(priv, ECON2, ECON2_AUTOINC | ECON2_VRPS);
+
+ enc28j60_rxfifo_init(priv, RXSTART_INIT, RXEND_INIT);
+ enc28j60_txfifo_init(priv, TXSTART_INIT, TXEND_INIT);
+
+ /*
+ * Check the RevID.
+ * If it's 0x00 or 0xFF probably the enc28j60 is not mounted or
+ * damaged
+ */
+ reg = enc28j60_regb_read(priv, EREVID);
+
+ if (netif_msg_drv(priv))
+ dev_info(&priv->edev.dev, ": chip RevID: 0x%02x\n", reg);
+
+ if (reg == 0x00 || reg == 0xff) {
+ if (netif_msg_drv(priv))
+ dev_dbg(&priv->edev.dev,
+ "%s() Invalid RevId %d\n", __func__, reg);
+ return 0;
+ }
+
+ /* default filter mode: (unicast OR broadcast) AND crc valid */
+ enc28j60_regb_write(priv, ERXFCON,
+ ERXFCON_UCEN | ERXFCON_CRCEN | ERXFCON_BCEN);
+
+ /* enable MAC receive */
+ enc28j60_regb_write(priv, MACON1,
+ MACON1_MARXEN | MACON1_TXPAUS | MACON1_RXPAUS);
+
+ /* enable automatic padding and CRC operations */
+ if (priv->full_duplex) {
+ enc28j60_regb_write(priv, MACON3,
+ MACON3_PADCFG0 | MACON3_TXCRCEN |
+ MACON3_FRMLNEN | MACON3_FULDPX);
+ /* set inter-frame gap (non-back-to-back) */
+ enc28j60_regb_write(priv, MAIPGL, 0x12);
+ /* set inter-frame gap (back-to-back) */
+ enc28j60_regb_write(priv, MABBIPG, 0x15);
+ } else {
+ enc28j60_regb_write(priv, MACON3,
+ MACON3_PADCFG0 | MACON3_TXCRCEN |
+ MACON3_FRMLNEN);
+ enc28j60_regb_write(priv, MACON4, 1 << 6); /* DEFER bit */
+ /* set inter-frame gap (non-back-to-back) */
+ enc28j60_regw_write(priv, MAIPGL, 0x0C12);
+ /* set inter-frame gap (back-to-back) */
+ enc28j60_regb_write(priv, MABBIPG, 0x12);
+ }
+ /*
+ * MACLCON1 (default)
+ * MACLCON2 (default)
+ * Set the maximum packet size which the controller will accept
+ */
+ enc28j60_regw_write(priv, MAMXFLL, MAX_FRAMELEN);
+
+ /* Configure LEDs */
+ if (!enc28j60_phy_write(priv, PHLCON, ENC28J60_LAMPS_MODE))
+ return 0;
+
+ if (priv->full_duplex) {
+ if (!enc28j60_phy_write(priv, PHCON1, PHCON1_PDPXMD))
+ return 0;
+ if (!enc28j60_phy_write(priv, PHCON2, 0x00))
+ return 0;
+ } else {
+ if (!enc28j60_phy_write(priv, PHCON1, 0x00))
+ return 0;
+ if (!enc28j60_phy_write(priv, PHCON2, PHCON2_HDLDIS))
+ return 0;
+ }
+
+ if (netif_msg_hw(priv))
+ enc28j60_dump_regs(priv, "Hw initialized.");
+
+ return 1;
+}
+
+static void enc28j60_hw_enable(struct enc28j60_net *priv)
+{
+ if (netif_msg_hw(priv))
+ dev_dbg(&priv->edev.dev, "%s()\n", __func__);
+
+ /* enable receive logic */
+ enc28j60_reg_bfset(priv, ECON1, ECON1_RXEN);
+ priv->hw_enable = true;
+}
+
+static void enc28j60_hw_disable(struct enc28j60_net *priv)
+{
+ /* disable interrutps and packet reception */
+ enc28j60_regb_write(priv, EIE, 0x00);
+ enc28j60_reg_bfclr(priv, ECON1, ECON1_RXEN);
+ priv->hw_enable = false;
+}
+
+/*
+ * Receive Status vector
+ */
+static void enc28j60_dump_rsv(struct enc28j60_net *priv, const char *msg,
+ u16 pk_ptr, int len, u16 sts)
+{
+ struct device_d *dev = &priv->edev.dev;
+
+ dev_dbg(dev, "%s - NextPk: 0x%04x - RSV:\n",
+ msg, pk_ptr);
+ dev_dbg(dev, "ByteCount: %d, DribbleNibble: %d\n", len,
+ RSV_GETBIT(sts, RSV_DRIBBLENIBBLE));
+ dev_dbg(dev, "RxOK: %d, CRCErr:%d, LenChkErr: %d,"
+ " LenOutOfRange: %d\n", RSV_GETBIT(sts, RSV_RXOK),
+ RSV_GETBIT(sts, RSV_CRCERROR),
+ RSV_GETBIT(sts, RSV_LENCHECKERR),
+ RSV_GETBIT(sts, RSV_LENOUTOFRANGE));
+ dev_dbg(dev, "Multicast: %d, Broadcast: %d, "
+ "LongDropEvent: %d, CarrierEvent: %d\n",
+ RSV_GETBIT(sts, RSV_RXMULTICAST),
+ RSV_GETBIT(sts, RSV_RXBROADCAST),
+ RSV_GETBIT(sts, RSV_RXLONGEVDROPEV),
+ RSV_GETBIT(sts, RSV_CARRIEREV));
+ dev_dbg(dev, "ControlFrame: %d, PauseFrame: %d,"
+ " UnknownOp: %d, VLanTagFrame: %d\n",
+ RSV_GETBIT(sts, RSV_RXCONTROLFRAME),
+ RSV_GETBIT(sts, RSV_RXPAUSEFRAME),
+ RSV_GETBIT(sts, RSV_RXUNKNOWNOPCODE),
+ RSV_GETBIT(sts, RSV_RXTYPEVLAN));
+}
+
+static void dump_packet(struct eth_device *edev,
+ const char *msg, int len, const char *data)
+{
+ dev_dbg(&edev->dev, "%s - packet len:%d\n", msg, len);
+ print_hex_dump(KERN_DEBUG, "pk data: ", DUMP_PREFIX_OFFSET, 16, 1,
+ data, len, true);
+}
+
+/*
+ * Hardware transmit function.
+ * Fill the buffer memory and send the contents of the transmit buffer
+ * onto the network
+ */
+static int enc28j60_eth_send(struct eth_device *edev, void *packet,
+ int packet_length)
+{
+ struct enc28j60_net *priv = edev->priv;
+
+ if (netif_msg_tx_queued(priv))
+ dev_dbg(&edev->dev, "Tx Packet Len:%d\n", packet_length);
+
+ if (netif_msg_pktdata(priv))
+ dump_packet(edev, __func__,
+ packet_length, packet);
+ enc28j60_packet_write(priv, packet_length, packet);
+
+ /* readback and verify written data */
+ if (IS_ENABLED(CONFIG_ENC28J60_WRITEVERIFY)) {
+ int test_len, k;
+ u8 test_buf[64]; /* limit the test to the first 64 bytes */
+ int okflag;
+
+ test_len = packet_length;
+ if (test_len > sizeof(test_buf))
+ test_len = sizeof(test_buf);
+
+ /* + 1 to skip control byte */
+ enc28j60_mem_read(priv, TXSTART_INIT + 1, test_len, test_buf);
+ okflag = 1;
+ for (k = 0; k < test_len; k++) {
+ if (((u8 *)packet)[k] != test_buf[k]) {
+ dev_dbg(&edev->dev,
+ "Error, %d location differ: "
+ "0x%02x-0x%02x\n", k,
+ ((u8 *)packet)[k], test_buf[k]);
+ okflag = 0;
+ }
+ }
+ if (!okflag)
+ dev_dbg(&edev->dev, "Tx write buffer verify ERROR!\n");
+ }
+
+ /* set TX request flag */
+ enc28j60_reg_bfset(priv, ECON1, ECON1_TXRTS);
+
+ return 0;
+}
+
+/*
+ * Hardware receive function.
+ * Read the buffer memory, update the FIFO pointer to free the buffer,
+ * check the status vector and decrement the packet counter.
+ */
+static void enc28j60_hw_rx(struct eth_device *edev)
+{
+ struct enc28j60_net *priv = edev->priv;
+ u16 erxrdpt, next_packet, rxstat;
+ u8 rsv[RSV_SIZE];
+ int len;
+
+ if (netif_msg_rx_status(priv))
+ dev_dbg(&edev->dev, "RX pk_addr:0x%04x\n", priv->next_pk_ptr);
+
+ if (unlikely(priv->next_pk_ptr > RXEND_INIT)) {
+ if (netif_msg_rx_err(priv))
+ dev_err(&edev->dev,
+ "%s() Invalid packet address!! 0x%04x\n",
+ __func__, priv->next_pk_ptr);
+
+ /* packet address corrupted: reset RX logic */
+ enc28j60_reg_bfclr(priv, ECON1, ECON1_RXEN);
+ enc28j60_reg_bfset(priv, ECON1, ECON1_RXRST);
+ enc28j60_reg_bfclr(priv, ECON1, ECON1_RXRST);
+ enc28j60_rxfifo_init(priv, RXSTART_INIT, RXEND_INIT);
+ enc28j60_reg_bfclr(priv, EIR, EIR_RXERIF);
+ enc28j60_reg_bfset(priv, ECON1, ECON1_RXEN);
+
+ return;
+ }
+
+ /* Read next packet pointer and rx status vector */
+ enc28j60_mem_read(priv, priv->next_pk_ptr, sizeof(rsv), rsv);
+
+ next_packet = rsv[1];
+ next_packet <<= 8;
+ next_packet |= rsv[0];
+
+ len = rsv[3];
+ len <<= 8;
+ len |= rsv[2];
+
+ rxstat = rsv[5];
+ rxstat <<= 8;
+ rxstat |= rsv[4];
+
+ if (netif_msg_rx_status(priv))
+ enc28j60_dump_rsv(priv, __func__, next_packet, len, rxstat);
+
+ if (!RSV_GETBIT(rxstat, RSV_RXOK) || len > MAX_FRAMELEN) {
+ if (netif_msg_rx_err(priv))
+ dev_err(&edev->dev, "Rx Error (%04x)\n", rxstat);
+ } else {
+ /* copy the packet from the receive buffer */
+ enc28j60_mem_read(priv,
+ rx_packet_start(priv->next_pk_ptr),
+ len, NetRxPackets[0]);
+
+ if (netif_msg_pktdata(priv))
+ dump_packet(edev, __func__, len, NetRxPackets[0]);
+
+ net_receive(edev, NetRxPackets[0], len);
+ }
+
+ /*
+ * Move the RX read pointer to the start of the next
+ * received packet.
+ * This frees the memory we just read out
+ */
+ erxrdpt = erxrdpt_workaround(next_packet, RXSTART_INIT, RXEND_INIT);
+ if (netif_msg_hw(priv))
+ dev_dbg(&edev->dev, ": %s() ERXRDPT:0x%04x\n",
+ __func__, erxrdpt);
+
+ enc28j60_regw_write(priv, ERXRDPTL, erxrdpt);
+
+ if (IS_ENABLED(CONFIG_ENC28J60_WRITEVERIFY) && netif_msg_drv(priv)) {
+ u16 reg;
+ reg = enc28j60_regw_read(priv, ERXRDPTL);
+ if (reg != erxrdpt)
+ dev_dbg(&edev->dev, "%s() ERXRDPT verify "
+ "error (0x%04x - 0x%04x)\n", __func__,
+ reg, erxrdpt);
+ }
+
+ priv->next_pk_ptr = next_packet;
+
+ /* we are done with this packet, decrement the packet counter */
+ enc28j60_reg_bfset(priv, ECON2, ECON2_PKTDEC);
+}
+
+/*
+ * Access the PHY to determine link status
+ */
+static void enc28j60_check_link_status(struct eth_device *edev)
+{
+ struct enc28j60_net *priv = edev->priv;
+ u16 reg;
+ int duplex;
+
+ reg = enc28j60_phy_read(priv, PHSTAT2);
+ if (netif_msg_hw(priv))
+ dev_dbg(&edev->dev,
+ "%s() PHSTAT1: %04x, PHSTAT2: %04x\n", __func__,
+ enc28j60_phy_read(priv, PHSTAT1), reg);
+ duplex = reg & PHSTAT2_DPXSTAT;
+
+ if (reg & PHSTAT2_LSTAT) {
+ if (netif_msg_ifup(priv))
+ dev_info(&edev->dev, "link up - %s\n",
+ duplex ? "Full duplex" : "Half duplex");
+ } else {
+ if (netif_msg_ifdown(priv))
+ dev_info(&edev->dev, "link down\n");
+ }
+}
+
+static int enc28j60_eth_rx(struct eth_device *edev)
+{
+ struct enc28j60_net *priv = edev->priv;
+ int pk_counter;
+
+ pk_counter = enc28j60_regb_read(priv, EPKTCNT);
+ if (pk_counter && netif_msg_intr(priv))
+ dev_dbg(&edev->dev, "intRX, pk_cnt: %d\n", pk_counter);
+
+ if (pk_counter > priv->max_pk_counter) {
+ priv->max_pk_counter = pk_counter;
+ if (netif_msg_rx_status(priv) && priv->max_pk_counter > 1)
+ dev_dbg(&edev->dev,
+ "RX max_pk_cnt: %d\n", priv->max_pk_counter);
+ }
+
+ while (pk_counter-- > 0)
+ enc28j60_hw_rx(edev);
+
+ return 0;
+}
+
+static int enc28j60_init_dev(struct eth_device *edev)
+{
+ /* FIXME: empty */
+
+ return 0;
+}
+
+/*
+ * Open/initialize the board. This is called (in the current kernel)
+ * sometime after booting when the 'ifconfig' program is run.
+ *
+ * This routine should set everything up anew at each open, even
+ * registers that "should" only need to be set once at boot, so that
+ * there is non-reboot way to recover if something goes wrong.
+ */
+static int enc28j60_eth_open(struct eth_device *edev)
+{
+ struct enc28j60_net *priv = edev->priv;
+ int ret;
+
+ if (netif_msg_drv(priv))
+ dev_dbg(&edev->dev, "%s() enter\n", __func__);
+
+ /* Reset the hardware here (and take it out of low power mode) */
+ enc28j60_lowpower(priv, false);
+ enc28j60_hw_disable(priv);
+ if (!enc28j60_hw_init(priv)) {
+ if (netif_msg_ifup(priv))
+ dev_err(&edev->dev, "hw_reset() failed\n");
+ return -EINVAL;
+ }
+
+ /* Update the MAC address after reset */
+ enc28j60_set_ethaddr(edev, priv->hwaddr);
+
+ enc28j60_hw_enable(priv);
+
+ /* Wait for link up after hardware reset */
+ mdelay(2000);
+
+ ret = phy_device_connect(edev, &priv->miibus, 0,
+ &enc28j60_check_link_status, 0,
+ PHY_INTERFACE_MODE_MII);
+
+ return ret;
+}
+
+static void enc28j60_eth_halt(struct eth_device *edev)
+{
+ struct enc28j60_net *priv = edev->priv;
+
+ if (netif_msg_drv(priv))
+ dev_dbg(&edev->dev, "%s() enter\n", __func__);
+
+ enc28j60_hw_disable(priv);
+ enc28j60_lowpower(priv, true);
+}
+
+static int enc28j60_probe(struct device_d *dev)
+{
+ struct eth_device *edev;
+ struct enc28j60_net *priv;
+ int ret = 0;
+
+ priv = xzalloc(sizeof(*priv));
+
+ priv->spi = (struct spi_device *)dev->type_data;
+ priv->msg_enable = netif_msg_init(0, ENC28J60_MSG_DEFAULT);
+
+ edev = &priv->edev;
+ edev->priv = priv;
+ edev->init = enc28j60_init_dev;
+ edev->open = enc28j60_eth_open;
+ edev->send = enc28j60_eth_send;
+ edev->recv = enc28j60_eth_rx;
+ edev->get_ethaddr = enc28j60_get_ethaddr;
+ edev->set_ethaddr = enc28j60_set_ethaddr;
+ edev->halt = enc28j60_eth_halt;
+ edev->parent = dev;
+
+ /*
+ * Here is a quote from ENC28J60 Data Sheet:
+ *
+ * The ENC28J60 does not support automatic duplex
+ * negotiation. If it is connected to an automatic duplex
+ * negotiation enabled network switch or Ethernet controller,
+ * the ENC28J60 will be detected as a half-duplex device.
+ *
+ * So most people prefer to set up half-duplex mode.
+ */
+ priv->full_duplex = 0;
+
+ if (!enc28j60_hw_init(priv)) {
+ if (netif_msg_probe(priv))
+ dev_info(dev, DRV_NAME " chip not found\n");
+ ret = -EIO;
+ goto error_register;
+ }
+
+ enc28j60_lowpower(priv, true);
+
+ priv->miibus.read = enc28j60_miibus_read;
+ priv->miibus.write = enc28j60_miibus_write;
+
+ priv->miibus.priv = priv;
+ priv->miibus.parent = dev;
+
+ ret = mdiobus_register(&priv->miibus);
+ if (ret)
+ goto error_register;
+
+ ret = eth_register(edev);
+ if (ret)
+ goto error_register;
+
+ dev_info(dev, DRV_NAME " driver registered\n");
+
+ return 0;
+
+error_register:
+ return ret;
+}
+
+static __maybe_unused struct of_device_id enc28j60_dt_ids[] = {
+ {
+ .compatible = "microchip,enc28j60",
+ }, {
+ /* sentinel */
+ }
+};
+
+static struct driver_d enc28j60_driver = {
+ .name = DRV_NAME,
+ .probe = enc28j60_probe,
+ .of_compatible = DRV_OF_COMPAT(enc28j60_dt_ids),
+};
+device_spi_driver(enc28j60_driver);
diff --git a/drivers/net/enc28j60_hw.h b/drivers/net/enc28j60_hw.h
new file mode 100644
index 0000000..4c023c8
--- /dev/null
+++ b/drivers/net/enc28j60_hw.h
@@ -0,0 +1,307 @@
+/*
+ * enc28j60_hw.h: EDTP FrameThrower style enc28j60 registers
+ */
+
+#ifndef _ENC28J60_HW_H
+#define _ENC28J60_HW_H
+
+/*
+ * ENC28J60 Control Registers
+ * Control register definitions are a combination of address,
+ * bank number, and Ethernet/MAC/PHY indicator bits.
+ * - Register address (bits 0-4)
+ * - Bank number (bits 5-6)
+ * - MAC/MII indicator (bit 7)
+ */
+#define ADDR_MASK 0x1F
+#define BANK_MASK 0x60
+#define SPRD_MASK 0x80
+/* All-bank registers */
+#define EIE 0x1B
+#define EIR 0x1C
+#define ESTAT 0x1D
+#define ECON2 0x1E
+#define ECON1 0x1F
+/* Bank 0 registers */
+#define ERDPTL (0x00|0x00)
+#define ERDPTH (0x01|0x00)
+#define EWRPTL (0x02|0x00)
+#define EWRPTH (0x03|0x00)
+#define ETXSTL (0x04|0x00)
+#define ETXSTH (0x05|0x00)
+#define ETXNDL (0x06|0x00)
+#define ETXNDH (0x07|0x00)
+#define ERXSTL (0x08|0x00)
+#define ERXSTH (0x09|0x00)
+#define ERXNDL (0x0A|0x00)
+#define ERXNDH (0x0B|0x00)
+#define ERXRDPTL (0x0C|0x00)
+#define ERXRDPTH (0x0D|0x00)
+#define ERXWRPTL (0x0E|0x00)
+#define ERXWRPTH (0x0F|0x00)
+#define EDMASTL (0x10|0x00)
+#define EDMASTH (0x11|0x00)
+#define EDMANDL (0x12|0x00)
+#define EDMANDH (0x13|0x00)
+#define EDMADSTL (0x14|0x00)
+#define EDMADSTH (0x15|0x00)
+#define EDMACSL (0x16|0x00)
+#define EDMACSH (0x17|0x00)
+/* Bank 1 registers */
+#define EHT0 (0x00|0x20)
+#define EHT1 (0x01|0x20)
+#define EHT2 (0x02|0x20)
+#define EHT3 (0x03|0x20)
+#define EHT4 (0x04|0x20)
+#define EHT5 (0x05|0x20)
+#define EHT6 (0x06|0x20)
+#define EHT7 (0x07|0x20)
+#define EPMM0 (0x08|0x20)
+#define EPMM1 (0x09|0x20)
+#define EPMM2 (0x0A|0x20)
+#define EPMM3 (0x0B|0x20)
+#define EPMM4 (0x0C|0x20)
+#define EPMM5 (0x0D|0x20)
+#define EPMM6 (0x0E|0x20)
+#define EPMM7 (0x0F|0x20)
+#define EPMCSL (0x10|0x20)
+#define EPMCSH (0x11|0x20)
+#define EPMOL (0x14|0x20)
+#define EPMOH (0x15|0x20)
+#define EWOLIE (0x16|0x20)
+#define EWOLIR (0x17|0x20)
+#define ERXFCON (0x18|0x20)
+#define EPKTCNT (0x19|0x20)
+/* Bank 2 registers */
+#define MACON1 (0x00|0x40|SPRD_MASK)
+/* #define MACON2 (0x01|0x40|SPRD_MASK) */
+#define MACON3 (0x02|0x40|SPRD_MASK)
+#define MACON4 (0x03|0x40|SPRD_MASK)
+#define MABBIPG (0x04|0x40|SPRD_MASK)
+#define MAIPGL (0x06|0x40|SPRD_MASK)
+#define MAIPGH (0x07|0x40|SPRD_MASK)
+#define MACLCON1 (0x08|0x40|SPRD_MASK)
+#define MACLCON2 (0x09|0x40|SPRD_MASK)
+#define MAMXFLL (0x0A|0x40|SPRD_MASK)
+#define MAMXFLH (0x0B|0x40|SPRD_MASK)
+#define MAPHSUP (0x0D|0x40|SPRD_MASK)
+#define MICON (0x11|0x40|SPRD_MASK)
+#define MICMD (0x12|0x40|SPRD_MASK)
+#define MIREGADR (0x14|0x40|SPRD_MASK)
+#define MIWRL (0x16|0x40|SPRD_MASK)
+#define MIWRH (0x17|0x40|SPRD_MASK)
+#define MIRDL (0x18|0x40|SPRD_MASK)
+#define MIRDH (0x19|0x40|SPRD_MASK)
+/* Bank 3 registers */
+#define MAADR1 (0x00|0x60|SPRD_MASK)
+#define MAADR0 (0x01|0x60|SPRD_MASK)
+#define MAADR3 (0x02|0x60|SPRD_MASK)
+#define MAADR2 (0x03|0x60|SPRD_MASK)
+#define MAADR5 (0x04|0x60|SPRD_MASK)
+#define MAADR4 (0x05|0x60|SPRD_MASK)
+#define EBSTSD (0x06|0x60)
+#define EBSTCON (0x07|0x60)
+#define EBSTCSL (0x08|0x60)
+#define EBSTCSH (0x09|0x60)
+#define MISTAT (0x0A|0x60|SPRD_MASK)
+#define EREVID (0x12|0x60)
+#define ECOCON (0x15|0x60)
+#define EFLOCON (0x17|0x60)
+#define EPAUSL (0x18|0x60)
+#define EPAUSH (0x19|0x60)
+/* PHY registers */
+#define PHCON1 0x00
+#define PHSTAT1 0x01
+#define PHHID1 0x02
+#define PHHID2 0x03
+#define PHCON2 0x10
+#define PHSTAT2 0x11
+#define PHIE 0x12
+#define PHIR 0x13
+#define PHLCON 0x14
+
+/* ENC28J60 EIE Register Bit Definitions */
+#define EIE_INTIE 0x80
+#define EIE_PKTIE 0x40
+#define EIE_DMAIE 0x20
+#define EIE_LINKIE 0x10
+#define EIE_TXIE 0x08
+/* #define EIE_WOLIE 0x04 (reserved) */
+#define EIE_TXERIE 0x02
+#define EIE_RXERIE 0x01
+/* ENC28J60 EIR Register Bit Definitions */
+#define EIR_PKTIF 0x40
+#define EIR_DMAIF 0x20
+#define EIR_LINKIF 0x10
+#define EIR_TXIF 0x08
+/* #define EIR_WOLIF 0x04 (reserved) */
+#define EIR_TXERIF 0x02
+#define EIR_RXERIF 0x01
+/* ENC28J60 ESTAT Register Bit Definitions */
+#define ESTAT_INT 0x80
+#define ESTAT_LATECOL 0x10
+#define ESTAT_RXBUSY 0x04
+#define ESTAT_TXABRT 0x02
+#define ESTAT_CLKRDY 0x01
+/* ENC28J60 ECON2 Register Bit Definitions */
+#define ECON2_AUTOINC 0x80
+#define ECON2_PKTDEC 0x40
+#define ECON2_PWRSV 0x20
+#define ECON2_VRPS 0x08
+/* ENC28J60 ECON1 Register Bit Definitions */
+#define ECON1_TXRST 0x80
+#define ECON1_RXRST 0x40
+#define ECON1_DMAST 0x20
+#define ECON1_CSUMEN 0x10
+#define ECON1_TXRTS 0x08
+#define ECON1_RXEN 0x04
+#define ECON1_BSEL1 0x02
+#define ECON1_BSEL0 0x01
+/* ENC28J60 MACON1 Register Bit Definitions */
+#define MACON1_LOOPBK 0x10
+#define MACON1_TXPAUS 0x08
+#define MACON1_RXPAUS 0x04
+#define MACON1_PASSALL 0x02
+#define MACON1_MARXEN 0x01
+/* ENC28J60 MACON2 Register Bit Definitions */
+#define MACON2_MARST 0x80
+#define MACON2_RNDRST 0x40
+#define MACON2_MARXRST 0x08
+#define MACON2_RFUNRST 0x04
+#define MACON2_MATXRST 0x02
+#define MACON2_TFUNRST 0x01
+/* ENC28J60 MACON3 Register Bit Definitions */
+#define MACON3_PADCFG2 0x80
+#define MACON3_PADCFG1 0x40
+#define MACON3_PADCFG0 0x20
+#define MACON3_TXCRCEN 0x10
+#define MACON3_PHDRLEN 0x08
+#define MACON3_HFRMLEN 0x04
+#define MACON3_FRMLNEN 0x02
+#define MACON3_FULDPX 0x01
+/* ENC28J60 MICMD Register Bit Definitions */
+#define MICMD_MIISCAN 0x02
+#define MICMD_MIIRD 0x01
+/* ENC28J60 MISTAT Register Bit Definitions */
+#define MISTAT_NVALID 0x04
+#define MISTAT_SCAN 0x02
+#define MISTAT_BUSY 0x01
+/* ENC28J60 ERXFCON Register Bit Definitions */
+#define ERXFCON_UCEN 0x80
+#define ERXFCON_ANDOR 0x40
+#define ERXFCON_CRCEN 0x20
+#define ERXFCON_PMEN 0x10
+#define ERXFCON_MPEN 0x08
+#define ERXFCON_HTEN 0x04
+#define ERXFCON_MCEN 0x02
+#define ERXFCON_BCEN 0x01
+
+/* ENC28J60 PHY PHCON1 Register Bit Definitions */
+#define PHCON1_PRST 0x8000
+#define PHCON1_PLOOPBK 0x4000
+#define PHCON1_PPWRSV 0x0800
+#define PHCON1_PDPXMD 0x0100
+/* ENC28J60 PHY PHSTAT1 Register Bit Definitions */
+#define PHSTAT1_PFDPX 0x1000
+#define PHSTAT1_PHDPX 0x0800
+#define PHSTAT1_LLSTAT 0x0004
+#define PHSTAT1_JBSTAT 0x0002
+/* ENC28J60 PHY PHSTAT2 Register Bit Definitions */
+#define PHSTAT2_TXSTAT (1 << 13)
+#define PHSTAT2_RXSTAT (1 << 12)
+#define PHSTAT2_COLSTAT (1 << 11)
+#define PHSTAT2_LSTAT (1 << 10)
+#define PHSTAT2_DPXSTAT (1 << 9)
+#define PHSTAT2_PLRITY (1 << 5)
+/* ENC28J60 PHY PHCON2 Register Bit Definitions */
+#define PHCON2_FRCLINK 0x4000
+#define PHCON2_TXDIS 0x2000
+#define PHCON2_JABBER 0x0400
+#define PHCON2_HDLDIS 0x0100
+/* ENC28J60 PHY PHIE Register Bit Definitions */
+#define PHIE_PLNKIE (1 << 4)
+#define PHIE_PGEIE (1 << 1)
+/* ENC28J60 PHY PHIR Register Bit Definitions */
+#define PHIR_PLNKIF (1 << 4)
+#define PHIR_PGEIF (1 << 1)
+
+/* ENC28J60 Packet Control Byte Bit Definitions */
+#define PKTCTRL_PHUGEEN 0x08
+#define PKTCTRL_PPADEN 0x04
+#define PKTCTRL_PCRCEN 0x02
+#define PKTCTRL_POVERRIDE 0x01
+
+/* ENC28J60 Transmit Status Vector */
+#define TSV_TXBYTECNT 0
+#define TSV_TXCOLLISIONCNT 16
+#define TSV_TXCRCERROR 20
+#define TSV_TXLENCHKERROR 21
+#define TSV_TXLENOUTOFRANGE 22
+#define TSV_TXDONE 23
+#define TSV_TXMULTICAST 24
+#define TSV_TXBROADCAST 25
+#define TSV_TXPACKETDEFER 26
+#define TSV_TXEXDEFER 27
+#define TSV_TXEXCOLLISION 28
+#define TSV_TXLATECOLLISION 29
+#define TSV_TXGIANT 30
+#define TSV_TXUNDERRUN 31
+#define TSV_TOTBYTETXONWIRE 32
+#define TSV_TXCONTROLFRAME 48
+#define TSV_TXPAUSEFRAME 49
+#define TSV_BACKPRESSUREAPP 50
+#define TSV_TXVLANTAGFRAME 51
+
+#define TSV_SIZE 7
+#define TSV_BYTEOF(x) ((x) / 8)
+#define TSV_BITMASK(x) (1 << ((x) % 8))
+#define TSV_GETBIT(x, y) (((x)[TSV_BYTEOF(y)] & TSV_BITMASK(y)) ? 1 : 0)
+
+/* ENC28J60 Receive Status Vector */
+#define RSV_RXLONGEVDROPEV 16
+#define RSV_CARRIEREV 18
+#define RSV_CRCERROR 20
+#define RSV_LENCHECKERR 21
+#define RSV_LENOUTOFRANGE 22
+#define RSV_RXOK 23
+#define RSV_RXMULTICAST 24
+#define RSV_RXBROADCAST 25
+#define RSV_DRIBBLENIBBLE 26
+#define RSV_RXCONTROLFRAME 27
+#define RSV_RXPAUSEFRAME 28
+#define RSV_RXUNKNOWNOPCODE 29
+#define RSV_RXTYPEVLAN 30
+
+#define RSV_SIZE 6
+#define RSV_BITMASK(x) (1 << ((x) - 16))
+#define RSV_GETBIT(x, y) (((x) & RSV_BITMASK(y)) ? 1 : 0)
+
+
+/* SPI operation codes */
+#define ENC28J60_READ_CTRL_REG 0x00
+#define ENC28J60_READ_BUF_MEM 0x3A
+#define ENC28J60_WRITE_CTRL_REG 0x40
+#define ENC28J60_WRITE_BUF_MEM 0x7A
+#define ENC28J60_BIT_FIELD_SET 0x80
+#define ENC28J60_BIT_FIELD_CLR 0xA0
+#define ENC28J60_SOFT_RESET 0xFF
+
+
+/* buffer boundaries applied to internal 8K ram
+ * entire available packet buffer space is allocated.
+ * Give TX buffer space for one full ethernet frame (~1500 bytes)
+ * receive buffer gets the rest */
+#define TXSTART_INIT 0x1A00
+#define TXEND_INIT 0x1FFF
+
+/* Put RX buffer at 0 as suggested by the Errata datasheet */
+#define RXSTART_INIT 0x0000
+#define RXEND_INIT 0x19FF
+
+/* maximum ethernet frame length */
+#define MAX_FRAMELEN 1518
+
+/* Preferred half duplex: LEDA: Link status LEDB: Rx/Tx activity */
+#define ENC28J60_LAMPS_MODE 0x3476
+
+#endif
diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
new file mode 100644
index 0000000..4884854
--- /dev/null
+++ b/include/linux/netdevice.h
@@ -0,0 +1,53 @@
+#ifndef _LINUX_NETDEVICE_H
+#define _LINUX_NETDEVICE_H
+
+/*
+ * Network interface message level settings
+ */
+
+enum {
+ NETIF_MSG_DRV = 0x0001,
+ NETIF_MSG_PROBE = 0x0002,
+ NETIF_MSG_LINK = 0x0004,
+ NETIF_MSG_TIMER = 0x0008,
+ NETIF_MSG_IFDOWN = 0x0010,
+ NETIF_MSG_IFUP = 0x0020,
+ NETIF_MSG_RX_ERR = 0x0040,
+ NETIF_MSG_TX_ERR = 0x0080,
+ NETIF_MSG_TX_QUEUED = 0x0100,
+ NETIF_MSG_INTR = 0x0200,
+ NETIF_MSG_TX_DONE = 0x0400,
+ NETIF_MSG_RX_STATUS = 0x0800,
+ NETIF_MSG_PKTDATA = 0x1000,
+ NETIF_MSG_HW = 0x2000,
+ NETIF_MSG_WOL = 0x4000,
+};
+
+#define netif_msg_drv(p) ((p)->msg_enable & NETIF_MSG_DRV)
+#define netif_msg_probe(p) ((p)->msg_enable & NETIF_MSG_PROBE)
+#define netif_msg_link(p) ((p)->msg_enable & NETIF_MSG_LINK)
+#define netif_msg_timer(p) ((p)->msg_enable & NETIF_MSG_TIMER)
+#define netif_msg_ifdown(p) ((p)->msg_enable & NETIF_MSG_IFDOWN)
+#define netif_msg_ifup(p) ((p)->msg_enable & NETIF_MSG_IFUP)
+#define netif_msg_rx_err(p) ((p)->msg_enable & NETIF_MSG_RX_ERR)
+#define netif_msg_tx_err(p) ((p)->msg_enable & NETIF_MSG_TX_ERR)
+#define netif_msg_tx_queued(p) ((p)->msg_enable & NETIF_MSG_TX_QUEUED)
+#define netif_msg_intr(p) ((p)->msg_enable & NETIF_MSG_INTR)
+#define netif_msg_tx_done(p) ((p)->msg_enable & NETIF_MSG_TX_DONE)
+#define netif_msg_rx_status(p) ((p)->msg_enable & NETIF_MSG_RX_STATUS)
+#define netif_msg_pktdata(p) ((p)->msg_enable & NETIF_MSG_PKTDATA)
+#define netif_msg_hw(p) ((p)->msg_enable & NETIF_MSG_HW)
+#define netif_msg_wol(p) ((p)->msg_enable & NETIF_MSG_WOL)
+
+static inline u32 netif_msg_init(int debug_value, int default_msg_enable_bits)
+{
+ /* use default */
+ if (debug_value < 0 || debug_value >= (sizeof(u32) * 8))
+ return default_msg_enable_bits;
+ if (debug_value == 0) /* no output */
+ return 0;
+ /* set low N bits */
+ return (1 << debug_value) - 1;
+}
+
+#endif /* _LINUX_NETDEVICE_H */
--
1.9.2
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 3+ messages in thread