[PATCH] Documentation: add mips boards files

* [PATCH] Documentation: add mips boards files
@ 2014-06-28 16:29 Antony Pavlov
  2014-06-30  6:00 ` Sascha Hauer
  0 siblings, 1 reply; 2+ messages in thread
From: Antony Pavlov @ 2014-06-28 16:29 UTC (permalink / raw)
  To: barebox

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
---
 Documentation/boards/mips.rst               |  9 ++++
 Documentation/boards/mips/dlink-dir-320.rst | 44 +++++++++++++++++++
 Documentation/boards/mips/loongson_ls1b.rst | 56 ++++++++++++++++++++++++
 Documentation/boards/mips/qemu-malta.rst    | 19 ++++++++
 Documentation/boards/mips/ritmix-rzx50.rst  | 62 ++++++++++++++++++++++++++
 Documentation/boards/mips/tplink-mr3020.rst | 67 +++++++++++++++++++++++++++++
 6 files changed, 257 insertions(+)

diff --git a/Documentation/boards/mips.rst b/Documentation/boards/mips.rst
new file mode 100644
index 0000000..4bac35f
--- /dev/null
+++ b/Documentation/boards/mips.rst
@@ -0,0 +1,9 @@
+MIPS
+====
+
+.. toctree::
+  :glob:
+  :numbered:
+  :maxdepth: 1
+
+  mips/*
diff --git a/Documentation/boards/mips/dlink-dir-320.rst b/Documentation/boards/mips/dlink-dir-320.rst
new file mode 100644
index 0000000..74d11ff
--- /dev/null
+++ b/Documentation/boards/mips/dlink-dir-320.rst
@@ -0,0 +1,44 @@
+D-Link DIR-320
+==============
+
+The D-Link DIR-320 wireless router has
+
+  * BCM5354 SoC;
+  * 32 MiB SDRAM;
+  * 4 MiB NOR type Flash Memory;
+  * RS232 serial interface (LV-TTL levels on board!);
+  * 1xUSB interface;
+  * 4 + 1 ethernet interfaces;
+  * 802.11b/g (WiFi) interface;
+  * JTAG interface;
+  * 5 LEDs;
+  * 2 buttons.
+
+The router uses CFE as firmware.
+
+Running barebox
+---------------
+
+Barebox can be started from CFE using tftp.
+You must setup tftp-server on host 192.168.0.1.
+Put your barebox.bin to tftp-server directory
+(usual /tftpboot or /srv/tftp).
+Connect your DIR-320 to your tftp-server network via
+one of four <LAN> sockets.
+
+Next, setup network on DIR-320 and run barebox.bin, e.g.::
+
+  CFE> ifconfig eth0 -addr=192.168.0.99
+  CFE> boot -tftp -addr=a0800000 -raw 192.168.0.1:barebox.bin
+
+
+Links
+-----
+
+  * http://www.dlink.com.au/products/?pid=768
+  * http://wiki.openwrt.org/toh/d-link/dir-320
+
+CFE links:
+
+  * http://www.broadcom.com/support/communications_processors/downloads.php#cfe
+  * http://www.linux-mips.org/wiki/CFE
diff --git a/Documentation/boards/mips/loongson_ls1b.rst b/Documentation/boards/mips/loongson_ls1b.rst
new file mode 100644
index 0000000..a833a86
--- /dev/null
+++ b/Documentation/boards/mips/loongson_ls1b.rst
@@ -0,0 +1,56 @@
+Loongson LS1B
+=============
+
+The LS1B is a development board made by Loongson Technology Corp. Ltd.
+
+The board has
+
+  * Loongson LS1B SoC 250 MHz;
+  * 64 MiB SDRAM;
+  * 512 KiB SPI boot ROM;
+  * 128M x 8 Bit NAND Flash Memory;
+  * 2 x RS232 serial interfaces (DB9 connectors);
+  * 2 x Ethernet interfaces;
+  * 4 x USB interfaces;
+  * microSD card slot;
+  * LCD display (480x272);
+  * audio controller;
+  * beeper;
+  * buttons;
+  * EJTAG 10-pin connector.
+
+The board uses PMON2000 as bootloader.
+
+Running barebox
+---------------
+
+  1. Connect to the boards's UART2;
+
+  2. Turn board's power on;
+
+  3. Wait ``Press <Enter> to execute loading image`` prompt and press the space key.
+
+  4. Build barebox and upload ``zbarebox.bin`` via Ymodem to the board:
+
+.. code-block:: none
+
+    PMON> ymodem base=0xa0200000
+
+..
+
+  5. Run barebox
+
+.. code-block:: none
+
+    PMON> g -e 0xa0200000
+
+..
+
+Links
+-----
+
+  * http://en.wikipedia.org/wiki/Loongson
+  * http://www.linux-mips.org/wiki/Loongson
+  * https://github.com/loongson-gz
+  * http://www.linux-mips.org/wiki/PMON_2000
+  * http://www.opsycon.se/PMON2000/Main
diff --git a/Documentation/boards/mips/qemu-malta.rst b/Documentation/boards/mips/qemu-malta.rst
new file mode 100644
index 0000000..be89ae3
--- /dev/null
+++ b/Documentation/boards/mips/qemu-malta.rst
@@ -0,0 +1,19 @@
+QEMU Malta
+==========
+
+QEMU run string::
+
+  qemu-system-mips -nodefaults -M malta -m 256 \
+      -nographic -serial stdio -monitor null \
+      -bios barebox-flash-image
+
+Also you can use GXemul::
+
+  gxemul -Q -x -e maltabe -M 256 0xbfc00000:barebox-flash-image
+
+Links
+-----
+
+  * http://www.linux-mips.org/wiki/Mips_Malta
+  * http://www.qemu.org/
+  * http://gxemul.sourceforge.net/
diff --git a/Documentation/boards/mips/ritmix-rzx50.rst b/Documentation/boards/mips/ritmix-rzx50.rst
new file mode 100644
index 0000000..a51fe3f
--- /dev/null
+++ b/Documentation/boards/mips/ritmix-rzx50.rst
@@ -0,0 +1,62 @@
+Ritmix RZX-50
+=============
+
+Ritmix RZX-50 is a portable game console for the Russian market.
+
+The portable game console has
+
+  * Ingenic JZ4755 SoC;
+  * 64 MiB SDRAM;
+  * 4 GiB microSDHC card / 4 GiB NAND type Flash Memory (internal boot device);
+  * RS232 serial interface (LV-TTL levels on the board!);
+  * LCD display (480x272);
+  * Video out interface;
+  * 1xUSB interface;
+  * buttons.
+
+The game console uses U-Boot 1.1.6 as bootloader.
+
+Running barebox
+---------------
+
+  1. Connect to the game console's UART
+     (see. http://a320.emulate.su/2012/01/19/uart-na-ritmix-rzx-50/);
+
+  2. Unblock U-Boot console
+     (see. http://a320.emulate.su/2012/01/25/rzx-50-dostup-k-konsoli-u-boot/);
+     Please note that U-Boot's Zmodem support does not work;
+
+  3. Boot Ritmix linux and login;
+
+  4. Build barebox and upload ``barebox.bin`` via Zmodem to the board:
+
+.. code-block:: none
+
+    # cd /tmp
+    # rz
+
+..
+
+  5. Write barebox to onboard flash:
+
+.. code-block:: none
+
+    # dd if=barebox.bin of=/dev/mmcblk0 seek=1048576 bs=1 count=262144
+
+..
+
+  6. Reboot RZX-50, next in U-Boot console start barebox:
+
+.. code-block:: none
+
+  CETUS # msc read 0xa0800000 0x100000 0x40000; g a0800000
+
+..
+
+
+Links
+-----
+
+  * http://www.ritmixrussia.ru/products/252/entertainment/game/rzx-50
+  * ftp://ftp.ingenic.cn/2soc/4755/JZ4755_ds.pdf
+  * ftp://ftp.ingenic.cn/3sw/01linux/01loader/u-boot/u-boot-1.1.6-jz-20110719-r1728-add-jz4770.patch.bz2
diff --git a/Documentation/boards/mips/tplink-mr3020.rst b/Documentation/boards/mips/tplink-mr3020.rst
new file mode 100644
index 0000000..c9e092c
--- /dev/null
+++ b/Documentation/boards/mips/tplink-mr3020.rst
@@ -0,0 +1,67 @@
+TP-LINK MR3020
+==============
+
+The TP-LINK MR3020 wireless router has
+
+  * Atheros ar9331 SoC;
+  * 32 MiB SDRAM;
+  * 4 MiB NOR type SPI Flash Memory;
+  * RS232 serial interface (LV-TTL levels on board!);
+  * 1 USB interface;
+  * 1 Ethernet interfaces;
+  * 802.11b/g/n (WiFi) interface;
+  * LEDs & buttons.
+
+The router uses U-Boot 1.1.4 as firmware.
+
+Running barebox
+---------------
+
+Barebox can be started from U-Boot using tftp.
+But you have to encode barebox image in a very special way.
+
+First obtain ``lzma`` and ``mktplinkfw`` utilities.
+
+The ``lzma`` utility can be obtained in Debian/Ubuntu
+distro by installing lzma package.
+
+The ``mktplinkfw`` utility can be obtained from openwrt, e.g.::
+
+  $ OWRTPREF=https://raw.githubusercontent.com/mirrors/openwrt/master
+  $ curl -OL $OWRTPREF/tools/firmware-utils/src/mktplinkfw.c \
+          -OL $OWRTPREF/tools/firmware-utils/src/md5.c \
+          -OL $OWRTPREF/tools/firmware-utils/src/md5.h
+  $ cc -o mktplinkfw mktplinkfw.c md5.c
+
+To convert your barebox.bin to U-Boot-loadable image (``6F01A8C0.img``)
+use this command sequence::
+
+  $ lzma -c -k barebox.bin > barebox.lzma
+  $ ./FW/mktplinkfw -c -H 0x07200103 -W 1 -N TL-WR720N-v3 \
+      -s -F 4Mlzma -k barebox.lzma -o 6F01A8C0.img
+
+You must setup tftp-server on host 192.168.0.1.
+Put your ``6F01A8C0.img`` to tftp-server directory
+(usual ``/tftpboot`` or ``/srv/tftp``).
+
+Connect your board to your tftp-server network via Ethernet.
+
+Next, setup network on MR3020 and run ``6F01A8C0.img``, e.g.::
+
+  hornet> set ipaddr 192.168.0.2
+  hornet> set serverip 192.168.0.1
+  hornet> tftpboot 0x81000000 6F01A8C0.img
+  hornet> bootm 0x81000000
+
+
+Links
+-----
+
+  * http://www.tp-link.com/en/products/details/?model=TL-MR3020
+  * http://wiki.openwrt.org/toh/tp-link/tl-mr3020
+  * https://wikidevi.com/wiki/TP-LINK_TL-MR3020
+
+See also
+
+  * http://www.eeboard.com/wp-content/uploads/downloads/2013/08/AR9331.pdf
+  * http://squonk42.github.io/TL-WR703N/
-- 
1.9.2


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

^ permalink raw reply	[flat|nested] 2+ messages in thread