[PATCH] mtd: gpmi-nand: Make sure clock is disabled during rate change

[PATCH] mtd: gpmi-nand: Make sure clock is disabled during rate change

[Sascha Hauer]

On i.MX6 GPMI Nand controller the clock must be disabled during
a rate change. Otherwise glitches on the clock line may occur
which result in errors like:

MXS NAND: Error sending command
MXS NAND: DMA read error

There were previous attempts to fix this. One is in:

54961378f0 imx6: clk: Gate off ENFC clock before setting clock rate

This patch added a clk_disable() right before the rate change. Since
a clk_disable() on a disabled clk is a no-op, the patch added a
clk_enable() to the i.MX6 clk driver in the hope that the clk is
enabled in the nand driver probe and the clk_disable() really takes
place.

This patch doesn't work. First of all it enabled the enfc_podf clk
which was not the one that was actually disabled in the nand driver,
resulting in the nand drivers call to clk_disable() still being a
no-op. Then this patch also only works only on the classic i.MX6 which
was the only one supported at that time, but not on the i.MX6UL, i.MX6SX
and i.MX6SL which have a separate clk driver.

Instead of adding more quirks to the other i.MX6 clk drivers, fix this
in the GPMI driver. We no longer call clk_disable() on a disabled clk,
but instead do a clk_enable() first which makes sure the hardware state
is synchronized to the usage count and the following clk_disable()
is really effective. At the same time we can (and actually must) remove
the quirk in the i.MX6 clk driver.

Also add clk_disable()/clk_enable() around another rate change in the
GPMI driver.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
 drivers/clk/imx/clk-imx6.c  | 1 -
 drivers/mtd/nand/nand_mxs.c | 5 ++++-
 2 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/imx/clk-imx6.c b/drivers/clk/imx/clk-imx6.c
index 8c3bb46a48..35b995dae2 100644
--- a/drivers/clk/imx/clk-imx6.c
+++ b/drivers/clk/imx/clk-imx6.c
@@ -527,7 +527,6 @@ static int imx6_ccm_probe(struct device_d *dev)
 	clk_enable(clks[IMX6QDL_CLK_MMDC_CH0_AXI_PODF]);
 	clk_enable(clks[IMX6QDL_CLK_PLL6_ENET]);
 	clk_enable(clks[IMX6QDL_CLK_SATA_REF_100M]);
-	clk_enable(clks[IMX6QDL_CLK_ENFC_PODF]);
 
 	clk_set_parent(clks[IMX6QDL_CLK_LVDS1_SEL], clks[IMX6QDL_CLK_SATA_REF_100M]);
 
diff --git a/drivers/mtd/nand/nand_mxs.c b/drivers/mtd/nand/nand_mxs.c
index 337748af48..0e0f5e68b2 100644
--- a/drivers/mtd/nand/nand_mxs.c
+++ b/drivers/mtd/nand/nand_mxs.c
@@ -2051,7 +2051,9 @@ static int mxs_nand_enable_edo_mode(struct mxs_nand_info *info)
 	nand->select_chip(mtd, -1);
 
 	/* [3] set the main IO clock, 100MHz for mode 5, 80MHz for mode 4. */
+	clk_disable(info->clk);
 	clk_set_rate(info->clk, (mode == 5) ? 100000000 : 80000000);
+	clk_enable(info->clk);
 
 	dev_dbg(info->dev, "using asynchronous EDO mode %d\n", mode);
 
@@ -2147,6 +2149,8 @@ static int mxs_nand_probe(struct device_d *dev)
 	if (IS_ERR(nand_info->clk))
 		return PTR_ERR(nand_info->clk);
 
+	clk_enable(nand_info->clk);
+
 	if (mxs_nand_is_imx6(nand_info)) {
 		clk_disable(nand_info->clk);
 		clk_set_rate(nand_info->clk, 22000000);
@@ -2154,7 +2158,6 @@ static int mxs_nand_probe(struct device_d *dev)
 		nand_info->dma_channel_base = 0;
 	} else {
 		nand_info->dma_channel_base = MXS_DMA_CHANNEL_AHB_APBH_GPMI0;
-		clk_enable(nand_info->clk);
 	}
 
 	err = mxs_nand_alloc_buffers(nand_info);
-- 
2.18.0


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox