From: Sascha Hauer <s.hauer@pengutronix.de>
To: Ahmad Fatoum <a.fatoum@pengutronix.de>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH 4/5] drivers: add COMPILE_TEST prompts to some on-by-default drivers
Date: Fri, 8 May 2020 14:50:59 +0200 [thread overview]
Message-ID: <20200508125059.GN5877@pengutronix.de> (raw)
In-Reply-To: <20200508123431.GM5877@pengutronix.de>
On Fri, May 08, 2020 at 02:34:31PM +0200, Sascha Hauer wrote:
> On Fri, May 08, 2020 at 08:25:29AM +0200, Ahmad Fatoum wrote:
> > Many clock source and GPIO controller drivers don't have a prompt, but
> > are instead default y if their respective platform is enabled. Maintain
> > this behavior, but add a prompt for when COMPILE_TEST is enabled, so
> > they can be included in test builds.
> >
> > Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
> > ---
> > drivers/clocksource/Kconfig | 16 +++++++++-------
> > drivers/gpio/Kconfig | 12 ++++++++----
> > drivers/pinctrl/Kconfig | 8 ++++----
> > 3 files changed, 21 insertions(+), 15 deletions(-)
> >
> > diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
> > index 8805cda39e02..bc2aae7ad723 100644
> > --- a/drivers/clocksource/Kconfig
> > +++ b/drivers/clocksource/Kconfig
> > @@ -75,16 +75,18 @@ config CLOCKSOURCE_ATMEL_PIT
> > bool
> >
> > config CLOCKSOURCE_ARM_ARCHITECTED_TIMER
> > - bool
> > - default y
> > - depends on ARM && (CPU_64v8 || CPU_V7)
> > + bool "ARM architected timer clock source" if COMPILE_TEST
> > + default y if ARM && (CPU_64v8 || CPU_V7)
> > + depends on (ARM && (CPU_64v8 || CPU_V7)) || COMPILE_TEST
>
> This driver compiles only on ARM. It uses get_cntpct() which is a
> contains inline assembly.
Skipped this hunk while applying and added the following patch to
actually make the Atmel MCI driver compilable when COMPILE_TEST is
selected.
Sascha
------------------------------8<-------------------------
From f4abcd9f1f7ddb5a032d8c07a6adcb95b31cb7c0 Mon Sep 17 00:00:00 2001
From: Sascha Hauer <s.hauer@pengutronix.de>
Date: Fri, 8 May 2020 14:45:00 +0200
Subject: [PATCH] ARM: at91: Move mci platform data to include/
To be able to add the Atmel mci driver to COMPILE_TEST move the
definition of struct atmel_mci_platform_data to include/ where it
can be reached from foreign SoCs as well.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
arch/arm/mach-at91/include/mach/board.h | 11 +----------
drivers/mci/atmel_mci.c | 2 +-
include/platform_data/atmel-mci.h | 15 +++++++++++++++
3 files changed, 17 insertions(+), 11 deletions(-)
create mode 100644 include/platform_data/atmel-mci.h
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index 4c4b51180c..033341e270 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -147,16 +147,7 @@ static inline struct device_d * at91_register_uart(unsigned id, unsigned pins)
}
#endif
-/* Multimedia Card Interface */
-struct atmel_mci_platform_data {
- unsigned slot_b;
- unsigned bus_width;
- int detect_pin;
- int wp_pin;
- char *devname;
-};
-
-void at91_add_device_mci(short mmc_id, struct atmel_mci_platform_data *data);
+#include <platform_data/atmel-mci.h>
/* SPI Master platform data */
struct at91_spi_platform_data {
diff --git a/drivers/mci/atmel_mci.c b/drivers/mci/atmel_mci.c
index 0d3b245ced..b4c4e7769e 100644
--- a/drivers/mci/atmel_mci.c
+++ b/drivers/mci/atmel_mci.c
@@ -21,9 +21,9 @@
#include <clock.h>
#include <gpio.h>
#include <io.h>
-#include <mach/board.h>
#include <linux/clk.h>
#include <linux/err.h>
+#include <platform_data/atmel-mci.h>
#include <of_gpio.h>
#include "atmel-mci-regs.h"
diff --git a/include/platform_data/atmel-mci.h b/include/platform_data/atmel-mci.h
new file mode 100644
index 0000000000..d99ee3d138
--- /dev/null
+++ b/include/platform_data/atmel-mci.h
@@ -0,0 +1,15 @@
+#ifndef PLATFORM_DATA_ATMEL_MCI_H
+#define PLATFORM_DATA_ATMEL_MCI_H
+
+/* Multimedia Card Interface */
+struct atmel_mci_platform_data {
+ unsigned slot_b;
+ unsigned bus_width;
+ int detect_pin;
+ int wp_pin;
+ char *devname;
+};
+
+void at91_add_device_mci(short mmc_id, struct atmel_mci_platform_data *data);
+
+#endif /* PLATFORM_DATA_ATMEL_MCI_H */
--
2.26.2
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2020-05-08 12:51 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-08 6:25 [PATCH 1/5] drivers: explicitly select dependency STMP_DEVICE for i.MX23/28 drivers Ahmad Fatoum
2020-05-08 6:25 ` [PATCH 2/5] common: introduce COMPILE_TEST option for build-testing Ahmad Fatoum
2020-05-08 6:25 ` [PATCH 3/5] drivers: mark first batch of compilable drivers for COMPILE_TEST Ahmad Fatoum
2020-05-08 6:25 ` [PATCH 4/5] drivers: add COMPILE_TEST prompts to some on-by-default drivers Ahmad Fatoum
2020-05-08 12:34 ` Sascha Hauer
2020-05-08 12:50 ` Sascha Hauer [this message]
2020-05-08 13:51 ` Ahmad Fatoum
2020-05-08 6:25 ` [PATCH 5/5] drivers: add COMPILE_TEST prompts for some off-by-default options Ahmad Fatoum
2020-05-08 7:45 ` Ahmad Fatoum
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200508125059.GN5877@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=a.fatoum@pengutronix.de \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox