From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from metis.ext.pengutronix.de ([2001:67c:670:201:290:27ff:fe1d:cc33]) by merlin.infradead.org with esmtps (Exim 4.92.3 #3 (Red Hat Linux)) id 1jqE5b-0003oM-0f for barebox@lists.infradead.org; Tue, 30 Jun 2020 11:06:11 +0000 From: Michael Grzeschik Date: Tue, 30 Jun 2020 13:06:03 +0200 Message-Id: <20200630110603.21577-3-m.grzeschik@pengutronix.de> In-Reply-To: <20200630110603.21577-1-m.grzeschik@pengutronix.de> References: <20200630110603.21577-1-m.grzeschik@pengutronix.de> MIME-Version: 1.0 List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: "barebox" Errors-To: barebox-bounces+u.kleine-koenig=pengutronix.de@lists.infradead.org Subject: [PATCH v2 2/2] drivers: net: phy: at803x: add phy clk setup via dts To: barebox@lists.infradead.org Cc: Ahmad Fatoum There are dt-bindings for the setup of the clk configuration in the phy. This patch adds support for these bindings in the driver. Reviewed-by: Ahmad Fatoum Signed-off-by: Michael Grzeschik --- v1 -> v2: - returning config_init directly with clk_out_config - removed superflous and wrong drv_name property drivers/net/phy/at803x.c | 178 +++++++++++++++++++++++++++++++++++++-- 1 file changed, 171 insertions(+), 7 deletions(-) diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index b43cb0d23e..de053a36fb 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -11,6 +11,9 @@ #include #include #include +#include +#include +#include #define AT803X_INTR_ENABLE 0x12 #define AT803X_INTR_STATUS 0x13 @@ -27,6 +30,164 @@ #define AT803X_DEBUG_SYSTEM_MODE_CTRL 0x05 #define AT803X_DEBUG_RGMII_TX_CLK_DLY (1 << 8) +/* AT803x supports either the XTAL input pad, an internal PLL or the + * DSP as clock reference for the clock output pad. The XTAL reference + * is only used for 25 MHz output, all other frequencies need the PLL. + * The DSP as a clock reference is used in synchronous ethernet + * applications. + * + * By default the PLL is only enabled if there is a link. Otherwise + * the PHY will go into low power state and disabled the PLL. You can + * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always + * enabled. + */ +#define AT803X_MMD7_CLK25M 0x8016 +#define AT803X_CLK_OUT_MASK GENMASK(4, 2) +#define AT803X_CLK_OUT_25MHZ_XTAL 0 +#define AT803X_CLK_OUT_25MHZ_DSP 1 +#define AT803X_CLK_OUT_50MHZ_PLL 2 +#define AT803X_CLK_OUT_50MHZ_DSP 3 +#define AT803X_CLK_OUT_62_5MHZ_PLL 4 +#define AT803X_CLK_OUT_62_5MHZ_DSP 5 +#define AT803X_CLK_OUT_125MHZ_PLL 6 +#define AT803X_CLK_OUT_125MHZ_DSP 7 + +/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask + * but doesn't support choosing between XTAL/PLL and DSP. + */ +#define AT8035_CLK_OUT_MASK GENMASK(4, 3) + +#define AT803X_CLK_OUT_STRENGTH_MASK GENMASK(8, 7) +#define AT803X_CLK_OUT_STRENGTH_FULL 0 +#define AT803X_CLK_OUT_STRENGTH_HALF 1 +#define AT803X_CLK_OUT_STRENGTH_QUARTER 2 + +#define ATH9331_PHY_ID 0x004dd041 +#define ATH8030_PHY_ID 0x004dd076 +#define ATH8031_PHY_ID 0x004dd074 +#define ATH8032_PHY_ID 0x004dd023 +#define ATH8035_PHY_ID 0x004dd072 +#define AT8030_PHY_ID_MASK 0xffffffef + +struct at803x_priv { + u16 clk_25m_reg; + u16 clk_25m_mask; +}; + +static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id) +{ + struct phy_driver *drv = to_phy_driver(phydev->dev.driver); + + return (phydev->phy_id & drv->phy_id_mask) + == (phy_id & drv->phy_id_mask); +} + +static int at803x_parse_dt(struct phy_device *phydev) +{ + const struct device_d *dev = &phydev->dev; + const struct device_node *node = dev->device_node; + struct at803x_priv *priv = phydev->priv; + unsigned int sel, mask; + u32 freq, strength; + int ret; + + ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq); + if (!ret) { + mask = AT803X_CLK_OUT_MASK; + switch (freq) { + case 25000000: + sel = AT803X_CLK_OUT_25MHZ_XTAL; + break; + case 50000000: + sel = AT803X_CLK_OUT_50MHZ_PLL; + break; + case 62500000: + sel = AT803X_CLK_OUT_62_5MHZ_PLL; + break; + case 125000000: + sel = AT803X_CLK_OUT_125MHZ_PLL; + break; + default: + dev_err(dev, "invalid qca,clk-out-frequency\n"); + return -EINVAL; + } + + priv->clk_25m_reg |= FIELD_PREP(mask, sel); + priv->clk_25m_mask |= mask; + + /* Fixup for the AR8030/AR8035. This chip has another mask and + * doesn't support the DSP reference. Eg. the lowest bit of the + * mask. The upper two bits select the same frequencies. Mask + * the lowest bit here. + * + * Warning: + * There was no datasheet for the AR8030 available so this is + * just a guess. But the AR8035 is listed as pin compatible + * to the AR8030 so there might be a good chance it works on + * the AR8030 too. + */ + if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) || + at803x_match_phy_id(phydev, ATH8035_PHY_ID)) { + priv->clk_25m_reg &= AT8035_CLK_OUT_MASK; + priv->clk_25m_mask &= AT8035_CLK_OUT_MASK; + } + } + + ret = of_property_read_u32(node, "qca,clk-out-strength", &strength); + if (!ret) { + priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK; + switch (strength) { + case AR803X_STRENGTH_FULL: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL; + break; + case AR803X_STRENGTH_HALF: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF; + break; + case AR803X_STRENGTH_QUARTER: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER; + break; + default: + dev_err(dev, "invalid qca,clk-out-strength\n"); + return -EINVAL; + } + } + + return 0; +} + +static int at803x_probe(struct phy_device *phydev) +{ + struct at803x_priv *priv; + + priv = kzalloc(sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + phydev->priv = priv; + + return at803x_parse_dt(phydev); +} + +static int at803x_clk_out_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int val; + + if (!priv->clk_25m_mask) + return 0; + + val = phy_read_mmd_indirect(phydev, AT803X_MMD7_CLK25M, MDIO_MMD_AN); + if (val < 0) + return val; + + val &= ~priv->clk_25m_mask; + val |= priv->clk_25m_reg; + + phy_write_mmd_indirect(phydev, AT803X_MMD7_CLK25M, MDIO_MMD_AN, val); + + return 0; +} + static int at803x_config_init(struct phy_device *phydev) { int ret; @@ -46,33 +207,36 @@ static int at803x_config_init(struct phy_device *phydev) return ret; } - return 0; + return at803x_clk_out_config(phydev); } static struct phy_driver at803x_driver[] = { { /* ATHEROS 8035 */ - .phy_id = 0x004dd072, - .phy_id_mask = 0xffffffef, + .phy_id = ATH8035_PHY_ID, + .phy_id_mask = AT8030_PHY_ID_MASK, .drv.name = "Atheros 8035 ethernet", + .probe = at803x_probe, .config_init = at803x_config_init, .features = PHY_GBIT_FEATURES, .config_aneg = &genphy_config_aneg, .read_status = &genphy_read_status, }, { /* ATHEROS 8030 */ - .phy_id = 0x004dd076, - .phy_id_mask = 0xffffffef, + .phy_id = ATH8030_PHY_ID, + .phy_id_mask = AT8030_PHY_ID_MASK, .drv.name = "Atheros 8030 ethernet", .config_init = at803x_config_init, + .probe = at803x_probe, .features = PHY_GBIT_FEATURES, .config_aneg = &genphy_config_aneg, .read_status = &genphy_read_status, }, { /* ATHEROS 8031 */ - .phy_id = 0x004dd074, - .phy_id_mask = 0xffffffef, + .phy_id = ATH8031_PHY_ID, + .phy_id_mask = AT8030_PHY_ID_MASK, .drv.name = "Atheros 8031 ethernet", + .probe = at803x_probe, .config_init = at803x_config_init, .features = PHY_GBIT_FEATURES, .config_aneg = &genphy_config_aneg, -- 2.27.0 _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox