[PATCH v1] serial: imx: set CTS if DT property "linux, rs485-enabled-at-boot-time" is present

[PATCH v1] serial: imx: set CTS if DT property "linux, rs485-enabled-at-boot-time" is present

[Oleksij Rempel]

If we have a "linux,rs485-enabled-at-boot-time" DT property, we should
set CTS flag as soon as possible to the active state. This will set an
RS485 transmitter to receive-enable mode. Otherwise the RS485 bus will
be blocked for entire system boot time and other bus participants will
not be able to communicate.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/serial/serial_imx.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/serial/serial_imx.c b/drivers/serial/serial_imx.c
index c0265fc2d7..fe9b15d8b5 100644
--- a/drivers/serial/serial_imx.c
+++ b/drivers/serial/serial_imx.c
@@ -60,6 +60,7 @@ struct imx_serial_priv {
 	void __iomem *regs;
 	struct clk *clk;
 	struct imx_serial_devtype_data *devtype;
+	bool rs485_mode;
 };
 
 static int imx_serial_reffreq(struct imx_serial_priv *priv)
@@ -107,6 +108,9 @@ static int imx_serial_init_port(struct console_device *cdev)
 
 	/* Enable FIFOs */
 	val = readl(regs + UCR2);
+	/* set CTS to not block RS485 bus */
+	if (priv->rs485_mode)
+		val |= UCR2_CTS;
 	val |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN;
 	writel(val, regs + UCR2);
 
@@ -252,6 +256,10 @@ static int imx_serial_probe(struct device_d *dev)
 	if (of_property_read_bool(dev->device_node, "fsl,dte-mode"))
 		priv->dte_mode = 1;
 
+	if (of_property_read_bool(dev->device_node,
+				  "linux,rs485-enabled-at-boot-time"))
+		priv->rs485_mode = 1;
+
 	imx_serial_init_port(cdev);
 
 	/* Enable UART */
-- 
2.28.0


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

Re: [PATCH v1] serial: imx: set CTS if DT property "linux, rs485-enabled-at-boot-time" is present

[Ahmad Fatoum]

Hi,

On 8/18/20 11:34 AM, Oleksij Rempel wrote:
> If we have a "linux,rs485-enabled-at-boot-time" DT property, we should
> set CTS flag as soon as possible to the active state. This will set an
> RS485 transmitter to receive-enable mode. Otherwise the RS485 bus will
> be blocked for entire system boot time and other bus participants will
> not be able to communicate.

(Sidenote: I'd have expected this to be done by pin configuration)

> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/serial/serial_imx.c | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/drivers/serial/serial_imx.c b/drivers/serial/serial_imx.c
> index c0265fc2d7..fe9b15d8b5 100644
> --- a/drivers/serial/serial_imx.c
> +++ b/drivers/serial/serial_imx.c
> @@ -60,6 +60,7 @@ struct imx_serial_priv {
>  	void __iomem *regs;
>  	struct clk *clk;
>  	struct imx_serial_devtype_data *devtype;
> +	bool rs485_mode;
>  };
>  
>  static int imx_serial_reffreq(struct imx_serial_priv *priv)
> @@ -107,6 +108,9 @@ static int imx_serial_init_port(struct console_device *cdev)
>  
>  	/* Enable FIFOs */
>  	val = readl(regs + UCR2);
> +	/* set CTS to not block RS485 bus */
> +	if (priv->rs485_mode)
> +		val |= UCR2_CTS;

jfyi: UCR2_CTS is without effect when UCR2_CTSC=1.
UCR2_CTSC is 0 on POR though, so I think it should be ok
to only touch UCR2_CTS 

>  	val |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN;
>  	writel(val, regs + UCR2);
>  
> @@ -252,6 +256,10 @@ static int imx_serial_probe(struct device_d *dev)
>  	if (of_property_read_bool(dev->device_node, "fsl,dte-mode"))
>  		priv->dte_mode = 1;
>  
> +	if (of_property_read_bool(dev->device_node,
> +				  "linux,rs485-enabled-at-boot-time"))
> +		priv->rs485_mode = 1;

You'll need to check rs485-rts-active-low absence as well, or you break
slave communication for other boards.

> +
>  	imx_serial_init_port(cdev);
>  
>  	/* Enable UART */
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox