From: Ahmad Fatoum <a.fatoum@pengutronix.de>
To: barebox@lists.infradead.org
Cc: ore@pengutronix.de, Ahmad Fatoum <a.fatoum@pengutronix.de>
Subject: [PATCH 9/9] net: dsa: add Realtek (rtl8365mb/rtl8366rb) switch support
Date: Mon, 16 Jan 2023 14:45:01 +0100 [thread overview]
Message-ID: <20230116134501.2006391-10-a.fatoum@pengutronix.de> (raw)
In-Reply-To: <20230116134501.2006391-1-a.fatoum@pengutronix.de>
This imports the Linux v6.1 state of the driver into barebox. This has
been tested with the RTL8365MB in (bitbanged) SMI mode.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
drivers/net/Kconfig | 2 +
drivers/net/Makefile | 1 +
drivers/net/realtek-dsa/Kconfig | 62 ++
drivers/net/realtek-dsa/Makefile | 7 +
drivers/net/realtek-dsa/dsa_priv.h | 77 ++
drivers/net/realtek-dsa/realtek-mdio.c | 226 +++++
drivers/net/realtek-dsa/realtek-smi.c | 502 ++++++++++
drivers/net/realtek-dsa/realtek.h | 105 ++
drivers/net/realtek-dsa/rtl8365mb.c | 1273 ++++++++++++++++++++++++
drivers/net/realtek-dsa/rtl8366rb.c | 1123 +++++++++++++++++++++
drivers/net/realtek-dsa/tag_rtl4_a.c | 103 ++
drivers/net/realtek-dsa/tag_rtl8_4.c | 205 ++++
drivers/net/realtek-dsa/tagger.c | 38 +
include/linux/barebox-wrapper.h | 1 +
include/linux/if_bridge.h | 9 +
include/net.h | 3 +-
16 files changed, 3736 insertions(+), 1 deletion(-)
create mode 100644 drivers/net/realtek-dsa/Kconfig
create mode 100644 drivers/net/realtek-dsa/Makefile
create mode 100644 drivers/net/realtek-dsa/dsa_priv.h
create mode 100644 drivers/net/realtek-dsa/realtek-mdio.c
create mode 100644 drivers/net/realtek-dsa/realtek-smi.c
create mode 100644 drivers/net/realtek-dsa/realtek.h
create mode 100644 drivers/net/realtek-dsa/rtl8365mb.c
create mode 100644 drivers/net/realtek-dsa/rtl8366rb.c
create mode 100644 drivers/net/realtek-dsa/tag_rtl4_a.c
create mode 100644 drivers/net/realtek-dsa/tag_rtl8_4.c
create mode 100644 drivers/net/realtek-dsa/tagger.c
create mode 100644 include/linux/if_bridge.h
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 2622f64651d2..30de1f544ca9 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -331,6 +331,8 @@ config DRIVER_NET_SJA1105
- SJA1105R (Gen. 2, SGMII, No TT-Ethernet)
- SJA1105S (Gen. 2, SGMII, TT-Ethernet)
+source "drivers/net/realtek-dsa/Kconfig"
+
endif
endmenu
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 7ff330a2bf42..e491af391ab1 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -44,3 +44,4 @@ obj-$(CONFIG_DRIVER_NET_EFI_SNP) += efi-snp.o
obj-$(CONFIG_DRIVER_NET_VIRTIO) += virtio.o
obj-$(CONFIG_DRIVER_NET_AG71XX) += ag71xx.o
obj-$(CONFIG_DRIVER_NET_LITEETH) += liteeth.o
+obj-$(CONFIG_DRIVER_NET_DSA_REALTEK) += realtek-dsa/
diff --git a/drivers/net/realtek-dsa/Kconfig b/drivers/net/realtek-dsa/Kconfig
new file mode 100644
index 000000000000..dd8599565f6e
--- /dev/null
+++ b/drivers/net/realtek-dsa/Kconfig
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: GPL-2.0-only
+menuconfig DRIVER_NET_DSA_REALTEK
+ tristate "Realtek Ethernet switch family support"
+ depends on DSA
+ select FIXED_PHY
+ select IRQ_DOMAIN
+ select REALTEK_PHY
+ select REGMAP
+ help
+ Select to enable support for Realtek Ethernet switch chips.
+
+ Note that at least one interface driver must be enabled for the
+ subdrivers to be loaded. Moreover, an interface driver cannot achieve
+ anything without at least one subdriver enabled.
+
+config NET_DSA_TAG_RTL4_A
+ bool
+ help
+ Selected to enable support for tagging frames for the
+ Realtek switches with 4 byte protocol A tags, sich as found in
+ the Realtek RTL8366RB.
+
+config NET_DSA_TAG_RTL8_4
+ bool
+ help
+ Selected to enable support for tagging frames for Realtek
+ switches with 8 byte protocol 4 tags, such as the Realtek RTL8365MB-VC.
+
+if DRIVER_NET_DSA_REALTEK
+
+
+config NET_DSA_REALTEK_MDIO
+ tristate "Realtek MDIO interface driver"
+ depends on OFDEVICE
+ help
+ Select to enable support for registering switches configured
+ through MDIO.
+
+config NET_DSA_REALTEK_SMI
+ tristate "Realtek SMI interface driver"
+ depends on OFDEVICE
+ help
+ Select to enable support for registering switches connected
+ through SMI.
+
+config NET_DSA_REALTEK_RTL8365MB
+ tristate "Realtek RTL8365MB switch subdriver"
+ imply NET_DSA_REALTEK_SMI
+ imply NET_DSA_REALTEK_MDIO
+ select NET_DSA_TAG_RTL8_4
+ help
+ Select to enable support for Realtek RTL8365MB-VC and RTL8367S.
+
+config NET_DSA_REALTEK_RTL8366RB
+ tristate "Realtek RTL8366RB switch subdriver"
+ imply NET_DSA_REALTEK_SMI
+ imply NET_DSA_REALTEK_MDIO
+ select NET_DSA_TAG_RTL4_A
+ help
+ Select to enable support for Realtek RTL8366RB.
+
+endif
diff --git a/drivers/net/realtek-dsa/Makefile b/drivers/net/realtek-dsa/Makefile
new file mode 100644
index 000000000000..3aafa0a8a7e5
--- /dev/null
+++ b/drivers/net/realtek-dsa/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_NET_DSA_REALTEK_MDIO) += realtek-mdio.o tagger.o
+obj-$(CONFIG_NET_DSA_REALTEK_SMI) += realtek-smi.o tagger.o
+obj-$(CONFIG_NET_DSA_REALTEK_RTL8366RB) += rtl8366rb.o
+obj-$(CONFIG_NET_DSA_REALTEK_RTL8365MB) += rtl8365mb.o
+obj-$(CONFIG_NET_DSA_TAG_RTL4_A) += tag_rtl4_a.o
+obj-$(CONFIG_NET_DSA_TAG_RTL8_4) += tag_rtl8_4.o
diff --git a/drivers/net/realtek-dsa/dsa_priv.h b/drivers/net/realtek-dsa/dsa_priv.h
new file mode 100644
index 000000000000..4cda51831054
--- /dev/null
+++ b/drivers/net/realtek-dsa/dsa_priv.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* SPDX-FileCopyrightText: (c) 2008-2009 Marvell Semiconductor */
+
+#ifndef __DSA_PRIV_H
+#define __DSA_PRIV_H
+
+#include <net.h>
+#include <linux/string.h>
+
+
+/* Helper for removing DSA header tags from packets in the RX path.
+ * Must not be called before skb_pull(len).
+ *
+ * Before:
+ * packet
+ * |
+ * v
+ * | | | | | | | | | | | | | | | | | | |
+ * +-----------------------+-----------------------+---------------+-------+
+ * | Destination MAC | Source MAC | DSA header | EType |
+ * +-----------------------+-----------------------+---------------+-------+
+ * | |
+ * <----- len ----->
+ * After:
+ *
+ * <----- len ----->
+ * |
+ * >>>>>>> v
+ * >>>>>>> | | | | | | | | | | | | | | |
+ * >>>>>>> +-----------------------+-----------------------+-------+
+ * >>>>>>> | Destination MAC | Source MAC | EType |
+ * +-----------------------+-----------------------+-------+
+ *
+ */
+static inline void dsa_strip_etype_header(void *packet, int len)
+{
+ memmove(packet + len, packet, 2 * ETH_ALEN);
+}
+
+/* Helper for creating space for DSA header tags in TX path packets.
+ *
+ * Before:
+ *
+ * <<<<<<< | | | | | | | | | | | | | | |
+ * ^ <<<<<<< +-----------------------+-----------------------+-------+
+ * | <<<<<<< | Destination MAC | Source MAC | EType |
+ * | +-----------------------+-----------------------+-------+
+ * <----- len ----->
+ * |
+ * |
+ * packet
+ *
+ * After:
+ *
+ * | | | | | | | | | | | | | | | | | | |
+ * +-----------------------+-----------------------+---------------+-------+
+ * | Destination MAC | Source MAC | DSA header | EType |
+ * +-----------------------+-----------------------+---------------+-------+
+ * ^ | |
+ * | <----- len ----->
+ * packet
+ */
+static inline void dsa_alloc_etype_header(void *packet, int len)
+{
+ memmove(packet, packet + len, 2 * ETH_ALEN);
+}
+
+/* On TX, skb->data points to skb_mac_header(skb), which means that EtherType
+ * header taggers start exactly where the EtherType is (the EtherType is
+ * treated as part of the DSA header).
+ */
+static inline void *dsa_etype_header_pos(void *packet)
+{
+ return packet + 2 * ETH_ALEN;
+}
+
+#endif
diff --git a/drivers/net/realtek-dsa/realtek-mdio.c b/drivers/net/realtek-dsa/realtek-mdio.c
new file mode 100644
index 000000000000..7c26841d2fac
--- /dev/null
+++ b/drivers/net/realtek-dsa/realtek-mdio.c
@@ -0,0 +1,226 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Realtek MDIO interface driver
+ *
+ * ASICs we intend to support with this driver:
+ *
+ * RTL8366 - The original version, apparently
+ * RTL8369 - Similar enough to have the same datsheet as RTL8366
+ * RTL8366RB - Probably reads out "RTL8366 revision B", has a quite
+ * different register layout from the other two
+ * RTL8366S - Is this "RTL8366 super"?
+ * RTL8367 - Has an OpenWRT driver as well
+ * RTL8368S - Seems to be an alternative name for RTL8366RB
+ * RTL8370 - Also uses SMI
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ * Copyright (C) 2010 Antti Seppälä <a.seppala@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <roman@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leitner@googlemail.com>
+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#include <of_device.h>
+#include <regmap.h>
+#include <clock.h>
+#include <gpiod.h>
+#include <linux/mdio.h>
+
+#include "realtek.h"
+
+/* Read/write via mdiobus */
+#define REALTEK_MDIO_CTRL0_REG 31
+#define REALTEK_MDIO_START_REG 29
+#define REALTEK_MDIO_CTRL1_REG 21
+#define REALTEK_MDIO_ADDRESS_REG 23
+#define REALTEK_MDIO_DATA_WRITE_REG 24
+#define REALTEK_MDIO_DATA_READ_REG 25
+
+#define REALTEK_MDIO_START_OP 0xFFFF
+#define REALTEK_MDIO_ADDR_OP 0x000E
+#define REALTEK_MDIO_READ_OP 0x0001
+#define REALTEK_MDIO_WRITE_OP 0x0003
+
+static int realtek_mdio_write(void *ctx, u32 reg, u32 val)
+{
+ struct realtek_priv *priv = ctx;
+ struct mii_bus *bus = priv->bus;
+ int ret;
+
+ ret = bus->write(bus, priv->mdio_addr, REALTEK_MDIO_CTRL0_REG, REALTEK_MDIO_ADDR_OP);
+ if (ret)
+ goto out_unlock;
+
+ ret = bus->write(bus, priv->mdio_addr, REALTEK_MDIO_ADDRESS_REG, reg);
+ if (ret)
+ goto out_unlock;
+
+ ret = bus->write(bus, priv->mdio_addr, REALTEK_MDIO_DATA_WRITE_REG, val);
+ if (ret)
+ goto out_unlock;
+
+ ret = bus->write(bus, priv->mdio_addr, REALTEK_MDIO_CTRL1_REG, REALTEK_MDIO_WRITE_OP);
+
+out_unlock:
+ return ret;
+}
+
+static int realtek_mdio_read(void *ctx, u32 reg, u32 *val)
+{
+ struct realtek_priv *priv = ctx;
+ struct mii_bus *bus = priv->bus;
+ int ret;
+
+ ret = bus->write(bus, priv->mdio_addr, REALTEK_MDIO_CTRL0_REG, REALTEK_MDIO_ADDR_OP);
+ if (ret)
+ goto out_unlock;
+
+ ret = bus->write(bus, priv->mdio_addr, REALTEK_MDIO_ADDRESS_REG, reg);
+ if (ret)
+ goto out_unlock;
+
+ ret = bus->write(bus, priv->mdio_addr, REALTEK_MDIO_CTRL1_REG, REALTEK_MDIO_READ_OP);
+ if (ret)
+ goto out_unlock;
+
+ ret = bus->read(bus, priv->mdio_addr, REALTEK_MDIO_DATA_READ_REG);
+ if (ret >= 0) {
+ *val = ret;
+ ret = 0;
+ }
+
+out_unlock:
+ return ret;
+}
+
+static const struct regmap_config realtek_mdio_regmap_config = {
+ .reg_bits = 10, /* A4..A0 R4..R0 */
+ .val_bits = 16,
+ .reg_stride = 1,
+ /* PHY regs are at 0x8000 */
+ .max_register = 0xffff,
+ .reg_format_endian = REGMAP_ENDIAN_BIG,
+};
+
+static const struct regmap_bus realtek_mdio_regmap_bus = {
+ .reg_write = realtek_mdio_write,
+ .reg_read = realtek_mdio_read,
+};
+
+static int realtek_mdio_probe(struct phy_device *mdiodev)
+{
+ struct realtek_priv *priv;
+ struct device *dev = &mdiodev->dev;
+ const struct realtek_variant *var;
+ struct regmap_config rc;
+ struct device_node *np;
+ int ret;
+
+ var = of_device_get_match_data(dev);
+ if (!var)
+ return -EINVAL;
+
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ rc = realtek_mdio_regmap_config;
+ priv->map = regmap_init(dev, &realtek_mdio_regmap_bus, priv, &rc);
+ if (IS_ERR(priv->map)) {
+ ret = PTR_ERR(priv->map);
+ dev_err(dev, "regmap init failed: %d\n", ret);
+ return ret;
+ }
+
+ priv->mdio_addr = mdiodev->addr;
+ priv->bus = mdiodev->bus;
+ priv->dev = &mdiodev->dev;
+ priv->chip_data = (void *)priv + sizeof(*priv);
+
+ priv->clk_delay = var->clk_delay;
+ priv->cmd_read = var->cmd_read;
+ priv->cmd_write = var->cmd_write;
+ priv->ops = var->ops;
+
+ priv->write_reg_noack = realtek_mdio_write;
+
+ np = dev->of_node;
+
+ dev->priv = priv;
+
+ /* TODO: if power is software controlled, set up any regulators here */
+ priv->leds_disabled = of_property_read_bool(np, "realtek,disable-leds");
+
+ priv->reset = gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+ if (priv->reset < 0 && priv->reset != -ENOENT)
+ return dev_err_probe(dev, priv->reset, "failed to get RESET GPIO\n");
+
+ if (gpio_is_valid(priv->reset)) {
+ gpiod_set_value(priv->reset, 1);
+ dev_dbg(dev, "asserted RESET\n");
+ mdelay(REALTEK_HW_STOP_DELAY);
+ gpiod_set_value(priv->reset, 0);
+ mdelay(REALTEK_HW_START_DELAY);
+ dev_dbg(dev, "deasserted RESET\n");
+ }
+
+ ret = priv->ops->detect(priv);
+ if (ret) {
+ dev_err(dev, "unable to detect switch\n");
+ return ret;
+ }
+
+ priv->ds = kzalloc(sizeof(*priv->ds), GFP_KERNEL);
+ if (!priv->ds)
+ return -ENOMEM;
+
+ priv->ds->dev = dev;
+ priv->ds->num_ports = priv->num_ports;
+ priv->ds->priv = priv;
+ priv->ds->ops = var->ds_ops_mdio;
+
+ ret = realtek_dsa_init_tagger(priv);
+ if (ret)
+ return ret;
+
+ ret = dsa_register_switch(priv->ds);
+ if (ret) {
+ dev_err(priv->dev, "unable to register switch ret = %d\n", ret);
+ return ret;
+ }
+
+ return priv->ops->setup ? priv->ops->setup(priv) : 0;
+}
+
+static void realtek_mdio_remove(struct phy_device *mdiodev)
+{
+ struct realtek_priv *priv = mdiodev->dev.priv;
+
+ /* leave the device reset asserted */
+ gpiod_set_value(priv->reset, 1);
+}
+
+static const struct of_device_id realtek_mdio_of_match[] = {
+#if IS_ENABLED(CONFIG_NET_DSA_REALTEK_RTL8366RB)
+ { .compatible = "realtek,rtl8366rb", .data = &rtl8366rb_variant, },
+#endif
+#if IS_ENABLED(CONFIG_NET_DSA_REALTEK_RTL8365MB)
+ { .compatible = "realtek,rtl8365mb", .data = &rtl8365mb_variant, },
+#endif
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, realtek_mdio_of_match);
+
+static struct phy_driver realtek_mdio_driver = {
+ .drv = {
+ .name = "realtek-mdio",
+ .of_match_table = of_match_ptr(realtek_mdio_of_match),
+ },
+ .probe = realtek_mdio_probe,
+ .remove = realtek_mdio_remove,
+};
+
+device_mdio_driver(realtek_mdio_driver);
+
+MODULE_AUTHOR("Luiz Angelo Daros de Luca <luizluca@gmail.com>");
+MODULE_DESCRIPTION("Driver for Realtek ethernet switch connected via MDIO interface");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/realtek-dsa/realtek-smi.c b/drivers/net/realtek-dsa/realtek-smi.c
new file mode 100644
index 000000000000..83d197dcdfcd
--- /dev/null
+++ b/drivers/net/realtek-dsa/realtek-smi.c
@@ -0,0 +1,502 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Realtek Simple Management Interface (SMI) driver
+ * It can be discussed how "simple" this interface is.
+ *
+ * The SMI protocol piggy-backs the MDIO MDC and MDIO signals levels
+ * but the protocol is not MDIO at all. Instead it is a Realtek
+ * pecularity that need to bit-bang the lines in a special way to
+ * communicate with the switch.
+ *
+ * ASICs we intend to support with this driver:
+ *
+ * RTL8366 - The original version, apparently
+ * RTL8369 - Similar enough to have the same datsheet as RTL8366
+ * RTL8366RB - Probably reads out "RTL8366 revision B", has a quite
+ * different register layout from the other two
+ * RTL8366S - Is this "RTL8366 super"?
+ * RTL8367 - Has an OpenWRT driver as well
+ * RTL8368S - Seems to be an alternative name for RTL8366RB
+ * RTL8370 - Also uses SMI
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ * Copyright (C) 2010 Antti Seppälä <a.seppala@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <roman@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leitner@googlemail.com>
+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <driver.h>
+#include <of.h>
+#include <of_device.h>
+#include <linux/mdio.h>
+#include <clock.h>
+#include <gpiod.h>
+#include <driver.h>
+#include <regmap.h>
+#include <linux/bitops.h>
+#include <linux/if_bridge.h>
+
+
+#include "realtek.h"
+
+#define REALTEK_SMI_ACK_RETRY_COUNT 5
+
+static inline void realtek_smi_clk_delay(struct realtek_priv *priv)
+{
+ ndelay(priv->clk_delay);
+}
+
+static void realtek_smi_start(struct realtek_priv *priv)
+{
+ /* Set GPIO pins to output mode, with initial state:
+ * SCK = 0, SDA = 1
+ */
+ gpiod_direction_output(priv->mdc, 0);
+ gpiod_direction_output(priv->mdio, 1);
+ realtek_smi_clk_delay(priv);
+
+ /* CLK 1: 0 -> 1, 1 -> 0 */
+ gpiod_set_value(priv->mdc, 1);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdc, 0);
+ realtek_smi_clk_delay(priv);
+
+ /* CLK 2: */
+ gpiod_set_value(priv->mdc, 1);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdio, 0);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdc, 0);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdio, 1);
+}
+
+static void realtek_smi_stop(struct realtek_priv *priv)
+{
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdio, 0);
+ gpiod_set_value(priv->mdc, 1);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdio, 1);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdc, 1);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdc, 0);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdc, 1);
+
+ /* Add a click */
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdc, 0);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdc, 1);
+
+ /* Set GPIO pins to input mode */
+ gpiod_direction_input(priv->mdio);
+ gpiod_direction_input(priv->mdc);
+}
+
+static void realtek_smi_write_bits(struct realtek_priv *priv, u32 data, u32 len)
+{
+ for (; len > 0; len--) {
+ realtek_smi_clk_delay(priv);
+
+ /* Prepare data */
+ gpiod_set_value(priv->mdio, !!(data & (1 << (len - 1))));
+ realtek_smi_clk_delay(priv);
+
+ /* Clocking */
+ gpiod_set_value(priv->mdc, 1);
+ realtek_smi_clk_delay(priv);
+ gpiod_set_value(priv->mdc, 0);
+ }
+}
+
+static void realtek_smi_read_bits(struct realtek_priv *priv, u32 len, u32 *data)
+{
+ gpiod_direction_input(priv->mdio);
+
+ for (*data = 0; len > 0; len--) {
+ u32 u;
+
+ realtek_smi_clk_delay(priv);
+
+ /* Clocking */
+ gpiod_set_value(priv->mdc, 1);
+ realtek_smi_clk_delay(priv);
+ u = !!gpiod_get_value(priv->mdio);
+ gpiod_set_value(priv->mdc, 0);
+
+ *data |= (u << (len - 1));
+ }
+
+ gpiod_direction_output(priv->mdio, 0);
+}
+
+static int realtek_smi_wait_for_ack(struct realtek_priv *priv)
+{
+ int retry_cnt;
+
+ retry_cnt = 0;
+ do {
+ u32 ack;
+
+ realtek_smi_read_bits(priv, 1, &ack);
+ if (ack == 0)
+ break;
+
+ if (++retry_cnt > REALTEK_SMI_ACK_RETRY_COUNT) {
+ dev_err(priv->dev, "ACK timeout\n");
+ return -ETIMEDOUT;
+ }
+ } while (1);
+
+ return 0;
+}
+
+static int realtek_smi_write_byte(struct realtek_priv *priv, u8 data)
+{
+ realtek_smi_write_bits(priv, data, 8);
+ return realtek_smi_wait_for_ack(priv);
+}
+
+static int realtek_smi_write_byte_noack(struct realtek_priv *priv, u8 data)
+{
+ realtek_smi_write_bits(priv, data, 8);
+ return 0;
+}
+
+static int realtek_smi_read_byte0(struct realtek_priv *priv, u8 *data)
+{
+ u32 t;
+
+ /* Read data */
+ realtek_smi_read_bits(priv, 8, &t);
+ *data = (t & 0xff);
+
+ /* Send an ACK */
+ realtek_smi_write_bits(priv, 0x00, 1);
+
+ return 0;
+}
+
+static int realtek_smi_read_byte1(struct realtek_priv *priv, u8 *data)
+{
+ u32 t;
+
+ /* Read data */
+ realtek_smi_read_bits(priv, 8, &t);
+ *data = (t & 0xff);
+
+ /* Send an ACK */
+ realtek_smi_write_bits(priv, 0x01, 1);
+
+ return 0;
+}
+
+static int realtek_smi_read_reg(struct realtek_priv *priv, u32 addr, u32 *data)
+{
+ unsigned long flags;
+ u8 lo = 0;
+ u8 hi = 0;
+ int ret;
+
+ spin_lock_irqsave(&priv->lock, flags);
+
+ realtek_smi_start(priv);
+
+ /* Send READ command */
+ ret = realtek_smi_write_byte(priv, priv->cmd_read);
+ if (ret)
+ goto out;
+
+ /* Set ADDR[7:0] */
+ ret = realtek_smi_write_byte(priv, addr & 0xff);
+ if (ret)
+ goto out;
+
+ /* Set ADDR[15:8] */
+ ret = realtek_smi_write_byte(priv, addr >> 8);
+ if (ret)
+ goto out;
+
+ /* Read DATA[7:0] */
+ realtek_smi_read_byte0(priv, &lo);
+ /* Read DATA[15:8] */
+ realtek_smi_read_byte1(priv, &hi);
+
+ *data = ((u32)lo) | (((u32)hi) << 8);
+
+ ret = 0;
+
+ out:
+ realtek_smi_stop(priv);
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return ret;
+}
+
+static int realtek_smi_write_reg(struct realtek_priv *priv,
+ u32 addr, u32 data, bool ack)
+{
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&priv->lock, flags);
+
+ realtek_smi_start(priv);
+
+ /* Send WRITE command */
+ ret = realtek_smi_write_byte(priv, priv->cmd_write);
+ if (ret)
+ goto out;
+
+ /* Set ADDR[7:0] */
+ ret = realtek_smi_write_byte(priv, addr & 0xff);
+ if (ret)
+ goto out;
+
+ /* Set ADDR[15:8] */
+ ret = realtek_smi_write_byte(priv, addr >> 8);
+ if (ret)
+ goto out;
+
+ /* Write DATA[7:0] */
+ ret = realtek_smi_write_byte(priv, data & 0xff);
+ if (ret)
+ goto out;
+
+ /* Write DATA[15:8] */
+ if (ack)
+ ret = realtek_smi_write_byte(priv, data >> 8);
+ else
+ ret = realtek_smi_write_byte_noack(priv, data >> 8);
+ if (ret)
+ goto out;
+
+ ret = 0;
+
+ out:
+ realtek_smi_stop(priv);
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return ret;
+}
+
+/* There is one single case when we need to use this accessor and that
+ * is when issueing soft reset. Since the device reset as soon as we write
+ * that bit, no ACK will come back for natural reasons.
+ */
+static int realtek_smi_write_reg_noack(void *ctx, u32 reg, u32 val)
+{
+ return realtek_smi_write_reg(ctx, reg, val, false);
+}
+
+/* Regmap accessors */
+
+static int realtek_smi_write(void *ctx, u32 reg, u32 val)
+{
+ struct realtek_priv *priv = ctx;
+
+ return realtek_smi_write_reg(priv, reg, val, true);
+}
+
+static int realtek_smi_read(void *ctx, u32 reg, u32 *val)
+{
+ struct realtek_priv *priv = ctx;
+
+ return realtek_smi_read_reg(priv, reg, val);
+}
+
+static const struct regmap_config realtek_smi_regmap_config = {
+ .reg_bits = 10, /* A4..A0 R4..R0 */
+ .val_bits = 16,
+ .reg_stride = 1,
+ /* PHY regs are at 0x8000 */
+ .max_register = 0xffff,
+ .reg_format_endian = REGMAP_ENDIAN_BIG,
+};
+
+static const struct regmap_bus realtek_smi_regmap_bus = {
+ .reg_read = realtek_smi_read,
+ .reg_write = realtek_smi_write,
+};
+
+static int realtek_smi_mdio_read(struct mii_bus *bus, int addr, int regnum)
+{
+ struct realtek_priv *priv = bus->priv;
+
+ return priv->ops->phy_read(priv, addr, regnum);
+}
+
+static int realtek_smi_mdio_write(struct mii_bus *bus, int addr, int regnum,
+ u16 val)
+{
+ struct realtek_priv *priv = bus->priv;
+
+ return priv->ops->phy_write(priv, addr, regnum, val);
+}
+
+static int realtek_smi_setup_mdio(struct dsa_switch *ds)
+{
+ struct realtek_priv *priv = ds->priv;
+ struct device_node *mdio_np;
+ int ret;
+
+ mdio_np = of_get_compatible_child(priv->dev->of_node, "realtek,smi-mdio");
+ if (!mdio_np) {
+ dev_err(priv->dev, "no MDIO bus node\n");
+ return -ENODEV;
+ }
+
+ priv->slave_mii_bus->priv = priv;
+ priv->slave_mii_bus->read = realtek_smi_mdio_read;
+ priv->slave_mii_bus->write = realtek_smi_mdio_write;
+ priv->slave_mii_bus->dev.of_node = mdio_np;
+ priv->slave_mii_bus->parent = priv->dev;
+ ds->slave_mii_bus = priv->slave_mii_bus;
+
+ ret = mdiobus_register(priv->slave_mii_bus);
+ if (ret) {
+ dev_err(priv->dev, "unable to register MDIO bus %pOF\n",
+ mdio_np);
+ goto err_put_node;
+ }
+
+ return 0;
+
+err_put_node:
+ of_node_put(mdio_np);
+
+ return ret;
+}
+
+static int realtek_smi_probe(struct device *dev)
+{
+ const struct realtek_variant *var;
+ struct realtek_priv *priv;
+ struct regmap_config rc;
+ struct device_node *np;
+ int ret;
+
+ var = of_device_get_match_data(dev);
+ np = dev->of_node;
+
+ priv = kzalloc(sizeof(*priv) + var->chip_data_sz, GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+ priv->chip_data = (void *)priv + sizeof(*priv);
+
+ rc = realtek_smi_regmap_config;
+ priv->map = regmap_init(dev, &realtek_smi_regmap_bus, priv, &rc);
+ if (IS_ERR(priv->map)) {
+ ret = PTR_ERR(priv->map);
+ dev_err(dev, "regmap init failed: %d\n", ret);
+ return ret;
+ }
+
+ /* Link forward and backward */
+ priv->dev = dev;
+ priv->clk_delay = var->clk_delay;
+ priv->cmd_read = var->cmd_read;
+ priv->cmd_write = var->cmd_write;
+ priv->ops = var->ops;
+
+ priv->setup_interface = realtek_smi_setup_mdio;
+ priv->write_reg_noack = realtek_smi_write_reg_noack;
+
+ dev->priv = priv;
+ spin_lock_init(&priv->lock);
+
+ /* TODO: if power is software controlled, set up any regulators here */
+
+ priv->reset = gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+ if (priv->reset < 0 && priv->reset != -ENOENT)
+ return dev_err_probe(dev, priv->reset, "failed to get RESET GPIO\n");
+
+ if (gpio_is_valid(priv->reset)) {
+ gpiod_set_value(priv->reset, 1);
+ dev_dbg(dev, "asserted RESET\n");
+ mdelay(REALTEK_HW_STOP_DELAY);
+ gpiod_set_value(priv->reset, 0);
+ mdelay(REALTEK_HW_START_DELAY);
+ dev_dbg(dev, "deasserted RESET\n");
+ }
+
+ /* Fetch MDIO pins */
+ priv->mdc = gpiod_get(dev, "mdc", GPIOD_OUT_LOW);
+ if (!gpio_is_valid(priv->mdc))
+ return dev_err_probe(dev, priv->mdc, "failed to get MDC GPIO\n");
+
+ priv->mdio = gpiod_get(dev, "mdio", GPIOD_OUT_LOW);
+ if (!gpio_is_valid(priv->mdio))
+ return dev_err_probe(dev, priv->mdio, "failed to get MDIO GPIO\n");
+
+ priv->leds_disabled = of_property_read_bool(np, "realtek,disable-leds");
+
+ ret = priv->ops->detect(priv);
+ if (ret) {
+ dev_err(dev, "unable to detect switch\n");
+ return ret;
+ }
+
+ priv->ds = kzalloc(sizeof(*priv->ds), GFP_KERNEL);
+ if (!priv->ds)
+ return -ENOMEM;
+
+ priv->ds->dev = dev;
+ priv->ds->num_ports = priv->num_ports;
+ priv->ds->priv = priv;
+ priv->ds->ops = var->ds_ops_smi;
+
+ ret = realtek_dsa_init_tagger(priv);
+ if (ret)
+ return ret;
+
+ ret = dsa_register_switch(priv->ds);
+ if (ret) {
+ dev_err_probe(dev, ret, "unable to register switch\n");
+ return ret;
+ }
+
+ return priv->ops->setup ? priv->ops->setup(priv) : 0;
+}
+
+static void realtek_smi_remove(struct device *dev)
+{
+ struct realtek_priv *priv = dev->priv;
+
+ /* leave the device reset asserted */
+ gpiod_set_value(priv->reset, 1);
+}
+
+static const struct of_device_id realtek_smi_of_match[] = {
+#if IS_ENABLED(CONFIG_NET_DSA_REALTEK_RTL8366RB)
+ {
+ .compatible = "realtek,rtl8366rb",
+ .data = &rtl8366rb_variant,
+ },
+#endif
+#if IS_ENABLED(CONFIG_NET_DSA_REALTEK_RTL8365MB)
+ {
+ .compatible = "realtek,rtl8365mb",
+ .data = &rtl8365mb_variant,
+ },
+#endif
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, realtek_smi_of_match);
+
+static struct driver realtek_smi_driver = {
+ .name = "realtek-smi",
+ .of_match_table = of_match_ptr(realtek_smi_of_match),
+ .probe = realtek_smi_probe,
+ .remove = realtek_smi_remove,
+};
+device_platform_driver(realtek_smi_driver);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
+MODULE_DESCRIPTION("Driver for Realtek ethernet switch connected via SMI interface");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/realtek-dsa/realtek.h b/drivers/net/realtek-dsa/realtek.h
new file mode 100644
index 000000000000..46a2282f6e6d
--- /dev/null
+++ b/drivers/net/realtek-dsa/realtek.h
@@ -0,0 +1,105 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/* Realtek SMI interface driver defines
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#ifndef _REALTEK_H
+#define _REALTEK_H
+
+#include <linux/spinlock.h>
+#include <linux/phy.h>
+#include <driver.h>
+#include <gpio.h>
+#include <dsa.h>
+
+#define REALTEK_HW_STOP_DELAY 25 /* msecs */
+#define REALTEK_HW_START_DELAY 100 /* msecs */
+
+struct realtek_ops;
+
+struct realtek_priv {
+ struct device *dev;
+ int reset;
+ int mdc;
+ int mdio;
+ union {
+ struct regmap *map;
+ struct regmap *map_nolock;
+ };
+ struct mii_bus slave_mii_bus[1];
+ struct mii_bus *bus;
+ int mdio_addr;
+
+ unsigned int clk_delay;
+ u8 cmd_read;
+ u8 cmd_write;
+ spinlock_t lock; /* Locks around command writes */
+ struct dsa_switch *ds;
+ bool leds_disabled;
+
+ unsigned int cpu_port;
+ unsigned int num_ports;
+
+ const struct realtek_ops *ops;
+ int (*setup_interface)(struct dsa_switch *ds);
+ int (*write_reg_noack)(void *ctx, u32 addr, u32 data);
+
+ char buf[4096];
+ void *chip_data; /* Per-chip extra variant data */
+};
+
+/*
+ * struct realtek_ops - vtable for the per-SMI-chiptype operations
+ * @detect: detects the chiptype
+ */
+struct realtek_ops {
+ int (*detect)(struct realtek_priv *priv);
+ int (*reset_chip)(struct realtek_priv *priv);
+ int (*setup)(struct realtek_priv *priv);
+ void (*cleanup)(struct realtek_priv *priv);
+ int (*enable_port)(struct realtek_priv *priv, int port, bool enable);
+ int (*phy_read)(struct realtek_priv *priv, int phy, int regnum);
+ int (*phy_write)(struct realtek_priv *priv, int phy, int regnum,
+ u16 val);
+ enum dsa_tag_protocol (*get_tag_protocol)(struct realtek_priv *priv);
+ int (*change_tag_protocol)(struct realtek_priv *priv,
+ enum dsa_tag_protocol proto);
+};
+
+struct realtek_variant {
+ const struct dsa_switch_ops *ds_ops_smi;
+ const struct dsa_switch_ops *ds_ops_mdio;
+ const struct realtek_ops *ops;
+ unsigned int clk_delay;
+ u8 cmd_read;
+ u8 cmd_write;
+ size_t chip_data_sz;
+};
+
+enum dsa_tag_protocol {
+ DSA_TAG_PROTO_RTL4_A = 17,
+ DSA_TAG_PROTO_RTL8_4 = 24,
+ DSA_TAG_PROTO_RTL8_4T = 25,
+};
+
+struct dsa_device_ops {
+ int (*xmit)(struct dsa_port *dp, int port, void *packet, int length);
+ int (*rcv)(struct dsa_switch *ds, int *portp, void *packet, int length);
+ unsigned int needed_headroom;
+ unsigned int needed_tailroom;
+ const char *name;
+ enum dsa_tag_protocol proto;
+};
+
+extern const struct realtek_variant rtl8366rb_variant;
+extern const struct realtek_variant rtl8365mb_variant;
+
+int realtek_dsa_init_tagger(struct realtek_priv *priv);
+
+extern const struct dsa_device_ops rtl4a_netdev_ops;
+extern const struct dsa_device_ops rtl8_4_netdev_ops;
+extern const struct dsa_device_ops rtl8_4t_netdev_ops;
+
+#endif /* _REALTEK_H */
diff --git a/drivers/net/realtek-dsa/rtl8365mb.c b/drivers/net/realtek-dsa/rtl8365mb.c
new file mode 100644
index 000000000000..8f7d122da28f
--- /dev/null
+++ b/drivers/net/realtek-dsa/rtl8365mb.c
@@ -0,0 +1,1273 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Realtek SMI subdriver for the Realtek RTL8365MB-VC ethernet switch.
+ *
+ * Copyright (C) 2021 Alvin Šipraga <alsi@bang-olufsen.dk>
+ * Copyright (C) 2021 Michael Rasmussen <mir@bang-olufsen.dk>
+ *
+ * The RTL8365MB-VC is a 4+1 port 10/100/1000M switch controller. It includes 4
+ * integrated PHYs for the user facing ports, and an extension interface which
+ * can be connected to the CPU - or another PHY - via either MII, RMII, or
+ * RGMII. The switch is configured via the Realtek Simple Management Interface
+ * (SMI), which uses the MDIO/MDC lines.
+ *
+ * Below is a simplified block diagram of the chip and its relevant interfaces.
+ *
+ * .-----------------------------------.
+ * | |
+ * UTP <---------------> Giga PHY <-> PCS <-> P0 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P1 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P2 GMAC |
+ * UTP <---------------> Giga PHY <-> PCS <-> P3 GMAC |
+ * | |
+ * CPU/PHY <-MII/RMII/RGMII---> Extension <---> Extension |
+ * | interface 1 GMAC 1 |
+ * | |
+ * SMI driver/ <-MDC/SCL---> Management ~~~~~~~~~~~~~~ |
+ * EEPROM <-MDIO/SDA--> interface ~REALTEK ~~~~~ |
+ * | ~RTL8365MB ~~~ |
+ * | ~GXXXC TAIWAN~ |
+ * GPIO <--------------> Reset ~~~~~~~~~~~~~~ |
+ * | |
+ * Interrupt <----------> Link UP/DOWN events |
+ * controller | |
+ * '-----------------------------------'
+ *
+ * The driver uses DSA to integrate the 4 user and 1 extension ports into the
+ * kernel. Netdevices are created for the user ports, as are PHY devices for
+ * their integrated PHYs. The device tree firmware should also specify the link
+ * partner of the extension port - either via a fixed-link or other phy-handle.
+ * See the device tree bindings for more detailed information. Note that the
+ * driver has only been tested with a fixed-link, but in principle it should not
+ * matter.
+ *
+ * NOTE: Currently, only the RGMII interface is implemented in this driver.
+ *
+ * The interrupt line is asserted on link UP/DOWN events. The driver creates a
+ * custom irqchip to handle this interrupt and demultiplex the events by reading
+ * the status registers via SMI. Interrupts are then propagated to the relevant
+ * PHY device.
+ *
+ * The EEPROM contains initial register values which the chip will read over I2C
+ * upon hardware reset. It is also possible to omit the EEPROM. In both cases,
+ * the driver will manually reprogram some registers using jam tables to reach
+ * an initial state defined by the vendor driver.
+ *
+ * This Linux driver is written based on an OS-agnostic vendor driver from
+ * Realtek. The reference GPL-licensed sources can be found in the OpenWrt
+ * source tree under the name rtl8367c. The vendor driver claims to support a
+ * number of similar switch controllers from Realtek, but the only hardware we
+ * have is the RTL8365MB-VC. Moreover, there does not seem to be any chip under
+ * the name RTL8367C. Although one wishes that the 'C' stood for some kind of
+ * common hardware revision, there exist examples of chips with the suffix -VC
+ * which are explicitly not supported by the rtl8367c driver and which instead
+ * require the rtl8367d vendor driver. With all this uncertainty, the driver has
+ * been modestly named rtl8365mb. Future implementors may wish to rename things
+ * accordingly.
+ *
+ * In the same family of chips, some carry up to 8 user ports and up to 2
+ * extension ports. Where possible this driver tries to make things generic, but
+ * more work must be done to support these configurations. According to
+ * documentation from Realtek, the family should include the following chips:
+ *
+ * - RTL8363NB
+ * - RTL8363NB-VB
+ * - RTL8363SC
+ * - RTL8363SC-VB
+ * - RTL8364NB
+ * - RTL8364NB-VB
+ * - RTL8365MB-VC
+ * - RTL8366SC
+ * - RTL8367RB-VB
+ * - RTL8367SB
+ * - RTL8367S
+ * - RTL8370MB
+ * - RTL8310SR
+ *
+ * Some of the register logic for these additional chips has been skipped over
+ * while implementing this driver. It is therefore not possible to assume that
+ * things will work out-of-the-box for other chips, and a careful review of the
+ * vendor driver may be needed to expand support. The RTL8365MB-VC seems to be
+ * one of the simpler chips.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <regmap.h>
+#include <net.h>
+#include <linux/if_bridge.h>
+
+#include "realtek.h"
+
+/* Family-specific data and limits */
+#define RTL8365MB_PHYADDRMAX 7
+#define RTL8365MB_NUM_PHYREGS 32
+#define RTL8365MB_PHYREGMAX (RTL8365MB_NUM_PHYREGS - 1)
+#define RTL8365MB_MAX_NUM_PORTS 11
+#define RTL8365MB_MAX_NUM_EXTINTS 3
+#define RTL8365MB_LEARN_LIMIT_MAX 2112
+
+/* Chip identification registers */
+#define RTL8365MB_CHIP_ID_REG 0x1300
+
+#define RTL8365MB_CHIP_VER_REG 0x1301
+
+#define RTL8365MB_MAGIC_REG 0x13C2
+#define RTL8365MB_MAGIC_VALUE 0x0249
+
+/* Chip reset register */
+#define RTL8365MB_CHIP_RESET_REG 0x1322
+#define RTL8365MB_CHIP_RESET_SW_MASK 0x0002
+#define RTL8365MB_CHIP_RESET_HW_MASK 0x0001
+
+/* Interrupt polarity register */
+#define RTL8365MB_INTR_POLARITY_REG 0x1100
+#define RTL8365MB_INTR_POLARITY_MASK 0x0001
+#define RTL8365MB_INTR_POLARITY_HIGH 0
+#define RTL8365MB_INTR_POLARITY_LOW 1
+
+/* Interrupt control/status register - enable/check specific interrupt types */
+#define RTL8365MB_INTR_CTRL_REG 0x1101
+#define RTL8365MB_INTR_STATUS_REG 0x1102
+#define RTL8365MB_INTR_SLIENT_START_2_MASK 0x1000
+#define RTL8365MB_INTR_SLIENT_START_MASK 0x0800
+#define RTL8365MB_INTR_ACL_ACTION_MASK 0x0200
+#define RTL8365MB_INTR_CABLE_DIAG_FIN_MASK 0x0100
+#define RTL8365MB_INTR_INTERRUPT_8051_MASK 0x0080
+#define RTL8365MB_INTR_LOOP_DETECTION_MASK 0x0040
+#define RTL8365MB_INTR_GREEN_TIMER_MASK 0x0020
+#define RTL8365MB_INTR_SPECIAL_CONGEST_MASK 0x0010
+#define RTL8365MB_INTR_SPEED_CHANGE_MASK 0x0008
+#define RTL8365MB_INTR_LEARN_OVER_MASK 0x0004
+#define RTL8365MB_INTR_METER_EXCEEDED_MASK 0x0002
+#define RTL8365MB_INTR_LINK_CHANGE_MASK 0x0001
+#define RTL8365MB_INTR_ALL_MASK \
+ (RTL8365MB_INTR_SLIENT_START_2_MASK | \
+ RTL8365MB_INTR_SLIENT_START_MASK | \
+ RTL8365MB_INTR_ACL_ACTION_MASK | \
+ RTL8365MB_INTR_CABLE_DIAG_FIN_MASK | \
+ RTL8365MB_INTR_INTERRUPT_8051_MASK | \
+ RTL8365MB_INTR_LOOP_DETECTION_MASK | \
+ RTL8365MB_INTR_GREEN_TIMER_MASK | \
+ RTL8365MB_INTR_SPECIAL_CONGEST_MASK | \
+ RTL8365MB_INTR_SPEED_CHANGE_MASK | \
+ RTL8365MB_INTR_LEARN_OVER_MASK | \
+ RTL8365MB_INTR_METER_EXCEEDED_MASK | \
+ RTL8365MB_INTR_LINK_CHANGE_MASK)
+
+/* Per-port interrupt type status registers */
+#define RTL8365MB_PORT_LINKDOWN_IND_REG 0x1106
+#define RTL8365MB_PORT_LINKDOWN_IND_MASK 0x07FF
+
+#define RTL8365MB_PORT_LINKUP_IND_REG 0x1107
+#define RTL8365MB_PORT_LINKUP_IND_MASK 0x07FF
+
+/* PHY indirect access registers */
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_REG 0x1F00
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK 0x0002
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ 0
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE 1
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK 0x0001
+#define RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE 1
+#define RTL8365MB_INDIRECT_ACCESS_STATUS_REG 0x1F01
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG 0x1F02
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK GENMASK(4, 0)
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK GENMASK(7, 5)
+#define RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK GENMASK(11, 8)
+#define RTL8365MB_PHY_BASE 0x2000
+#define RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG 0x1F03
+#define RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG 0x1F04
+
+/* PHY OCP address prefix register */
+#define RTL8365MB_GPHY_OCP_MSB_0_REG 0x1D15
+#define RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK 0x0FC0
+#define RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK 0xFC00
+
+/* The PHY OCP addresses of PHY registers 0~31 start here */
+#define RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE 0xA400
+
+/* External interface port mode values - used in DIGITAL_INTERFACE_SELECT */
+#define RTL8365MB_EXT_PORT_MODE_DISABLE 0
+#define RTL8365MB_EXT_PORT_MODE_RGMII 1
+#define RTL8365MB_EXT_PORT_MODE_MII_MAC 2
+#define RTL8365MB_EXT_PORT_MODE_MII_PHY 3
+#define RTL8365MB_EXT_PORT_MODE_TMII_MAC 4
+#define RTL8365MB_EXT_PORT_MODE_TMII_PHY 5
+#define RTL8365MB_EXT_PORT_MODE_GMII 6
+#define RTL8365MB_EXT_PORT_MODE_RMII_MAC 7
+#define RTL8365MB_EXT_PORT_MODE_RMII_PHY 8
+#define RTL8365MB_EXT_PORT_MODE_SGMII 9
+#define RTL8365MB_EXT_PORT_MODE_HSGMII 10
+#define RTL8365MB_EXT_PORT_MODE_1000X_100FX 11
+#define RTL8365MB_EXT_PORT_MODE_1000X 12
+#define RTL8365MB_EXT_PORT_MODE_100FX 13
+
+/* External interface mode configuration registers 0~1 */
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 0x1305 /* EXT1 */
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 0x13C3 /* EXT2 */
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(_extint) \
+ ((_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG0 : \
+ (_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_SELECT_REG1 : \
+ 0x0)
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(_extint) \
+ (0xF << (((_extint) % 2)))
+#define RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(_extint) \
+ (((_extint) % 2) * 4)
+
+/* External interface RGMII TX/RX delay configuration registers 0~2 */
+#define RTL8365MB_EXT_RGMXF_REG0 0x1306 /* EXT0 */
+#define RTL8365MB_EXT_RGMXF_REG1 0x1307 /* EXT1 */
+#define RTL8365MB_EXT_RGMXF_REG2 0x13C5 /* EXT2 */
+#define RTL8365MB_EXT_RGMXF_REG(_extint) \
+ ((_extint) == 0 ? RTL8365MB_EXT_RGMXF_REG0 : \
+ (_extint) == 1 ? RTL8365MB_EXT_RGMXF_REG1 : \
+ (_extint) == 2 ? RTL8365MB_EXT_RGMXF_REG2 : \
+ 0x0)
+#define RTL8365MB_EXT_RGMXF_RXDELAY_MASK 0x0007
+#define RTL8365MB_EXT_RGMXF_TXDELAY_MASK 0x0008
+
+/* External interface port speed values - used in DIGITAL_INTERFACE_FORCE */
+#define RTL8365MB_PORT_SPEED_10M 0
+#define RTL8365MB_PORT_SPEED_100M 1
+#define RTL8365MB_PORT_SPEED_1000M 2
+
+/* External interface force configuration registers 0~2 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 0x1310 /* EXT0 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 0x1311 /* EXT1 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 0x13C4 /* EXT2 */
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(_extint) \
+ ((_extint) == 0 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG0 : \
+ (_extint) == 1 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG1 : \
+ (_extint) == 2 ? RTL8365MB_DIGITAL_INTERFACE_FORCE_REG2 : \
+ 0x0)
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK 0x1000
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_NWAY_MASK 0x0080
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK 0x0040
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK 0x0020
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK 0x0010
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK 0x0004
+#define RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK 0x0003
+
+/* CPU port mask register - controls which ports are treated as CPU ports */
+#define RTL8365MB_CPU_PORT_MASK_REG 0x1219
+#define RTL8365MB_CPU_PORT_MASK_MASK 0x07FF
+
+/* CPU control register */
+#define RTL8365MB_CPU_CTRL_REG 0x121A
+#define RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK 0x0400
+#define RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK 0x0200
+#define RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK 0x0080
+#define RTL8365MB_CPU_CTRL_TAG_POSITION_MASK 0x0040
+#define RTL8365MB_CPU_CTRL_TRAP_PORT_MASK 0x0038
+#define RTL8365MB_CPU_CTRL_INSERTMODE_MASK 0x0006
+#define RTL8365MB_CPU_CTRL_EN_MASK 0x0001
+
+/* Maximum packet length register */
+#define RTL8365MB_CFG0_MAX_LEN_REG 0x088C
+#define RTL8365MB_CFG0_MAX_LEN_MASK 0x3FFF
+
+/* Port learning limit registers */
+#define RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE 0x0A20
+#define RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(_physport) \
+ (RTL8365MB_LUT_PORT_LEARN_LIMIT_BASE + (_physport))
+
+/* Port isolation (forwarding mask) registers */
+#define RTL8365MB_PORT_ISOLATION_REG_BASE 0x08A2
+#define RTL8365MB_PORT_ISOLATION_REG(_physport) \
+ (RTL8365MB_PORT_ISOLATION_REG_BASE + (_physport))
+#define RTL8365MB_PORT_ISOLATION_MASK 0x07FF
+
+/* MSTP port state registers - indexed by tree instance */
+#define RTL8365MB_MSTI_CTRL_BASE 0x0A00
+#define RTL8365MB_MSTI_CTRL_REG(_msti, _physport) \
+ (RTL8365MB_MSTI_CTRL_BASE + ((_msti) << 1) + ((_physport) >> 3))
+#define RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(_physport) ((_physport) << 1)
+#define RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(_physport) \
+ (0x3 << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET((_physport)))
+
+struct rtl8365mb_jam_tbl_entry {
+ u16 reg;
+ u16 val;
+};
+
+/* Lifted from the vendor driver sources */
+static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_8365mb_vc[] = {
+ { 0x13EB, 0x15BB }, { 0x1303, 0x06D6 }, { 0x1304, 0x0700 },
+ { 0x13E2, 0x003F }, { 0x13F9, 0x0090 }, { 0x121E, 0x03CA },
+ { 0x1233, 0x0352 }, { 0x1237, 0x00A0 }, { 0x123A, 0x0030 },
+ { 0x1239, 0x0084 }, { 0x0301, 0x1000 }, { 0x1349, 0x001F },
+ { 0x18E0, 0x4004 }, { 0x122B, 0x241C }, { 0x1305, 0xC000 },
+ { 0x13F0, 0x0000 },
+};
+
+static const struct rtl8365mb_jam_tbl_entry rtl8365mb_init_jam_common[] = {
+ { 0x1200, 0x7FCB }, { 0x0884, 0x0003 }, { 0x06EB, 0x0001 },
+ { 0x03Fa, 0x0007 }, { 0x08C8, 0x00C0 }, { 0x0A30, 0x020E },
+ { 0x0800, 0x0000 }, { 0x0802, 0x0000 }, { 0x09DA, 0x0013 },
+ { 0x1D32, 0x0002 },
+};
+
+enum rtl8365mb_phy_interface_mode {
+ RTL8365MB_PHY_INTERFACE_MODE_INVAL = 0,
+ RTL8365MB_PHY_INTERFACE_MODE_INTERNAL = BIT(0),
+ RTL8365MB_PHY_INTERFACE_MODE_MII = BIT(1),
+ RTL8365MB_PHY_INTERFACE_MODE_TMII = BIT(2),
+ RTL8365MB_PHY_INTERFACE_MODE_RMII = BIT(3),
+ RTL8365MB_PHY_INTERFACE_MODE_RGMII = BIT(4),
+ RTL8365MB_PHY_INTERFACE_MODE_SGMII = BIT(5),
+ RTL8365MB_PHY_INTERFACE_MODE_HSGMII = BIT(6),
+};
+
+/**
+ * struct rtl8365mb_extint - external interface info
+ * @port: the port with an external interface
+ * @id: the external interface ID, which is either 0, 1, or 2
+ * @supported_interfaces: a bitmask of supported PHY interface modes
+ *
+ * Represents a mapping: port -> { id, supported_interfaces }. To be embedded
+ * in &struct rtl8365mb_chip_info for every port with an external interface.
+ */
+struct rtl8365mb_extint {
+ int port;
+ int id;
+ unsigned int supported_interfaces;
+};
+
+/**
+ * struct rtl8365mb_chip_info - static chip-specific info
+ * @name: human-readable chip name
+ * @chip_id: chip identifier
+ * @chip_ver: chip silicon revision
+ * @extints: available external interfaces
+ * @jam_table: chip-specific initialization jam table
+ * @jam_size: size of the chip's jam table
+ *
+ * These data are specific to a given chip in the family of switches supported
+ * by this driver. When adding support for another chip in the family, a new
+ * chip info should be added to the rtl8365mb_chip_infos array.
+ */
+struct rtl8365mb_chip_info {
+ const char *name;
+ u32 chip_id;
+ u32 chip_ver;
+ const struct rtl8365mb_extint extints[RTL8365MB_MAX_NUM_EXTINTS];
+ const struct rtl8365mb_jam_tbl_entry *jam_table;
+ size_t jam_size;
+};
+
+/* Chip info for each supported switch in the family */
+#define PHY_INTF(_mode) (RTL8365MB_PHY_INTERFACE_MODE_ ## _mode)
+static const struct rtl8365mb_chip_info rtl8365mb_chip_infos[] = {
+ {
+ .name = "RTL8365MB-VC",
+ .chip_id = 0x6367,
+ .chip_ver = 0x0040,
+ .extints = {
+ { 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) |
+ PHY_INTF(RMII) | PHY_INTF(RGMII) },
+ },
+ .jam_table = rtl8365mb_init_jam_8365mb_vc,
+ .jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc),
+ },
+ {
+ .name = "RTL8367S",
+ .chip_id = 0x6367,
+ .chip_ver = 0x00A0,
+ .extints = {
+ { 6, 1, PHY_INTF(SGMII) | PHY_INTF(HSGMII) },
+ { 7, 2, PHY_INTF(MII) | PHY_INTF(TMII) |
+ PHY_INTF(RMII) | PHY_INTF(RGMII) },
+ },
+ .jam_table = rtl8365mb_init_jam_8365mb_vc,
+ .jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc),
+ },
+ {
+ .name = "RTL8367RB-VB",
+ .chip_id = 0x6367,
+ .chip_ver = 0x0020,
+ .extints = {
+ { 6, 1, PHY_INTF(MII) | PHY_INTF(TMII) |
+ PHY_INTF(RMII) | PHY_INTF(RGMII) },
+ { 7, 2, PHY_INTF(MII) | PHY_INTF(TMII) |
+ PHY_INTF(RMII) | PHY_INTF(RGMII) },
+ },
+ .jam_table = rtl8365mb_init_jam_8365mb_vc,
+ .jam_size = ARRAY_SIZE(rtl8365mb_init_jam_8365mb_vc),
+ },
+};
+
+enum rtl8365mb_stp_state {
+ RTL8365MB_STP_STATE_DISABLED = 0,
+ RTL8365MB_STP_STATE_BLOCKING = 1,
+ RTL8365MB_STP_STATE_LEARNING = 2,
+ RTL8365MB_STP_STATE_FORWARDING = 3,
+};
+
+enum rtl8365mb_cpu_insert {
+ RTL8365MB_CPU_INSERT_TO_ALL = 0,
+ RTL8365MB_CPU_INSERT_TO_TRAPPING = 1,
+ RTL8365MB_CPU_INSERT_TO_NONE = 2,
+};
+
+enum rtl8365mb_cpu_position {
+ RTL8365MB_CPU_POS_AFTER_SA = 0,
+ RTL8365MB_CPU_POS_BEFORE_CRC = 1,
+};
+
+enum rtl8365mb_cpu_format {
+ RTL8365MB_CPU_FORMAT_8BYTES = 0,
+ RTL8365MB_CPU_FORMAT_4BYTES = 1,
+};
+
+enum rtl8365mb_cpu_rxlen {
+ RTL8365MB_CPU_RXLEN_72BYTES = 0,
+ RTL8365MB_CPU_RXLEN_64BYTES = 1,
+};
+
+/**
+ * struct rtl8365mb_cpu - CPU port configuration
+ * @mask: port mask of ports that parse should parse CPU tags
+ * @trap_port: forward trapped frames to this port
+ * @insert: CPU tag insertion mode in switch->CPU frames
+ * @position: position of CPU tag in frame
+ * @rx_length: minimum CPU RX length
+ * @format: CPU tag format
+ *
+ * Represents the CPU tagging and CPU port configuration of the switch. These
+ * settings are configurable at runtime.
+ */
+struct rtl8365mb_cpu {
+ u32 mask;
+ u32 trap_port;
+ enum rtl8365mb_cpu_insert insert;
+ enum rtl8365mb_cpu_position position;
+ enum rtl8365mb_cpu_rxlen rx_length;
+ enum rtl8365mb_cpu_format format;
+};
+
+/**
+ * struct rtl8365mb_port - private per-port data
+ * @priv: pointer to parent realtek_priv data
+ * @index: DSA port index, same as dsa_port::index
+ */
+struct rtl8365mb_port {
+ struct realtek_priv *priv;
+ unsigned int index;
+};
+
+/**
+ * struct rtl8365mb - driver private data
+ * @priv: pointer to parent realtek_priv data
+ * @irq: registered IRQ or zero
+ * @chip_info: chip-specific info about the attached switch
+ * @cpu: CPU tagging and CPU port configuration for this chip
+ * @ports: per-port data
+ *
+ * Private data for this driver.
+ */
+struct rtl8365mb {
+ struct realtek_priv *priv;
+ const struct rtl8365mb_chip_info *chip_info;
+ struct rtl8365mb_cpu cpu;
+ struct rtl8365mb_port ports[RTL8365MB_MAX_NUM_PORTS];
+};
+
+static int rtl8365mb_phy_poll_busy(struct realtek_priv *priv)
+{
+ u32 val;
+
+ return regmap_read_poll_timeout(priv->map_nolock,
+ RTL8365MB_INDIRECT_ACCESS_STATUS_REG,
+ val, !val, 100);
+}
+
+static int rtl8365mb_phy_ocp_prepare(struct realtek_priv *priv, int phy,
+ u32 ocp_addr)
+{
+ u32 val;
+ int ret;
+
+ /* Set OCP prefix */
+ val = FIELD_GET(RTL8365MB_PHY_OCP_ADDR_PREFIX_MASK, ocp_addr);
+ ret = regmap_update_bits(
+ priv->map_nolock, RTL8365MB_GPHY_OCP_MSB_0_REG,
+ RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK,
+ FIELD_PREP(RTL8365MB_GPHY_OCP_MSB_0_CFG_CPU_OCPADR_MASK, val));
+ if (ret)
+ return ret;
+
+ /* Set PHY register address */
+ val = RTL8365MB_PHY_BASE;
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK, phy);
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_5_1_MASK,
+ ocp_addr >> 1);
+ val |= FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_ADDRESS_OCPADR_9_6_MASK,
+ ocp_addr >> 6);
+ ret = regmap_write(priv->map_nolock,
+ RTL8365MB_INDIRECT_ACCESS_ADDRESS_REG, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_phy_ocp_read(struct realtek_priv *priv, int phy,
+ u32 ocp_addr, u16 *data)
+{
+ u32 val;
+ int ret;
+
+ ret = rtl8365mb_phy_poll_busy(priv);
+ if (ret)
+ goto out;
+
+ ret = rtl8365mb_phy_ocp_prepare(priv, phy, ocp_addr);
+ if (ret)
+ goto out;
+
+ /* Execute read operation */
+ val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) |
+ FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_RW_READ);
+ ret = regmap_write(priv->map_nolock, RTL8365MB_INDIRECT_ACCESS_CTRL_REG,
+ val);
+ if (ret)
+ goto out;
+
+ ret = rtl8365mb_phy_poll_busy(priv);
+ if (ret)
+ goto out;
+
+ /* Get PHY register data */
+ ret = regmap_read(priv->map_nolock,
+ RTL8365MB_INDIRECT_ACCESS_READ_DATA_REG, &val);
+ if (ret)
+ goto out;
+
+ *data = val & 0xFFFF;
+
+out:
+
+ return ret;
+}
+
+static int rtl8365mb_phy_ocp_write(struct realtek_priv *priv, int phy,
+ u32 ocp_addr, u16 data)
+{
+ u32 val;
+ int ret;
+
+ ret = rtl8365mb_phy_poll_busy(priv);
+ if (ret)
+ goto out;
+
+ ret = rtl8365mb_phy_ocp_prepare(priv, phy, ocp_addr);
+ if (ret)
+ goto out;
+
+ /* Set PHY register data */
+ ret = regmap_write(priv->map_nolock,
+ RTL8365MB_INDIRECT_ACCESS_WRITE_DATA_REG, data);
+ if (ret)
+ goto out;
+
+ /* Execute write operation */
+ val = FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_CMD_VALUE) |
+ FIELD_PREP(RTL8365MB_INDIRECT_ACCESS_CTRL_RW_MASK,
+ RTL8365MB_INDIRECT_ACCESS_CTRL_RW_WRITE);
+ ret = regmap_write(priv->map_nolock, RTL8365MB_INDIRECT_ACCESS_CTRL_REG,
+ val);
+ if (ret)
+ goto out;
+
+ ret = rtl8365mb_phy_poll_busy(priv);
+ if (ret)
+ goto out;
+
+out:
+ return 0;
+}
+
+static int rtl8365mb_phy_read(struct realtek_priv *priv, int phy, int regnum)
+{
+ u32 ocp_addr;
+ u16 val;
+ int ret;
+
+ if (phy > RTL8365MB_PHYADDRMAX)
+ return -EINVAL;
+
+ if (regnum > RTL8365MB_PHYREGMAX)
+ return -EINVAL;
+
+ ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2;
+
+ ret = rtl8365mb_phy_ocp_read(priv, phy, ocp_addr, &val);
+ if (ret) {
+ dev_err(priv->dev,
+ "failed to read PHY%d reg %02x @ %04x, ret %d\n", phy,
+ regnum, ocp_addr, ret);
+ return ret;
+ }
+
+ dev_dbg(priv->dev, "read PHY%d register 0x%02x @ %04x, val <- %04x\n",
+ phy, regnum, ocp_addr, val);
+
+ return val;
+}
+
+static int rtl8365mb_phy_write(struct realtek_priv *priv, int phy, int regnum,
+ u16 val)
+{
+ u32 ocp_addr;
+ int ret;
+
+ if (phy > RTL8365MB_PHYADDRMAX)
+ return -EINVAL;
+
+ if (regnum > RTL8365MB_PHYREGMAX)
+ return -EINVAL;
+
+ ocp_addr = RTL8365MB_PHY_OCP_ADDR_PHYREG_BASE + regnum * 2;
+
+ ret = rtl8365mb_phy_ocp_write(priv, phy, ocp_addr, val);
+ if (ret) {
+ dev_err(priv->dev,
+ "failed to write PHY%d reg %02x @ %04x, ret %d\n", phy,
+ regnum, ocp_addr, ret);
+ return ret;
+ }
+
+ dev_dbg(priv->dev, "write PHY%d register 0x%02x @ %04x, val -> %04x\n",
+ phy, regnum, ocp_addr, val);
+
+ return 0;
+}
+
+static int rtl8365mb_dsa_phy_read(struct dsa_switch *ds, int phy, int regnum)
+{
+ return rtl8365mb_phy_read(ds->priv, phy, regnum);
+}
+
+static int rtl8365mb_dsa_phy_write(struct dsa_switch *ds, int phy, int regnum,
+ u16 val)
+{
+ return rtl8365mb_phy_write(ds->priv, phy, regnum, val);
+}
+
+static const struct rtl8365mb_extint *
+rtl8365mb_get_port_extint(struct realtek_priv *priv, int port)
+{
+ struct rtl8365mb *mb = priv->chip_data;
+ int i;
+
+ for (i = 0; i < RTL8365MB_MAX_NUM_EXTINTS; i++) {
+ const struct rtl8365mb_extint *extint =
+ &mb->chip_info->extints[i];
+
+ if (extint->port == port)
+ return extint;
+ }
+
+ return NULL;
+}
+
+static enum dsa_tag_protocol
+rtl8365mb_get_tag_protocol(struct realtek_priv *priv)
+{
+ struct rtl8365mb_cpu *cpu;
+ struct rtl8365mb *mb;
+
+ mb = priv->chip_data;
+ cpu = &mb->cpu;
+
+ if (cpu->position == RTL8365MB_CPU_POS_BEFORE_CRC)
+ return DSA_TAG_PROTO_RTL8_4T;
+
+ return DSA_TAG_PROTO_RTL8_4;
+}
+
+static int rtl8365mb_ext_config_rgmii(struct realtek_priv *priv, int port,
+ phy_interface_t interface)
+{
+ const struct rtl8365mb_extint *extint =
+ rtl8365mb_get_port_extint(priv, port);
+ struct device_node *dn;
+ struct dsa_port *dp;
+ int tx_delay = 0;
+ int rx_delay = 0;
+ u32 val;
+ int ret;
+
+ if (!extint)
+ return -ENODEV;
+
+ dp = dsa_to_port(priv->ds, port);
+ dn = dp->dev->device_node;
+
+ /* Set the RGMII TX/RX delay
+ *
+ * The Realtek vendor driver indicates the following possible
+ * configuration settings:
+ *
+ * TX delay:
+ * 0 = no delay, 1 = 2 ns delay
+ * RX delay:
+ * 0 = no delay, 7 = maximum delay
+ * Each step is approximately 0.3 ns, so the maximum delay is about
+ * 2.1 ns.
+ *
+ * The vendor driver also states that this must be configured *before*
+ * forcing the external interface into a particular mode, which is done
+ * in the rtl8365mb_phylink_mac_link_{up,down} functions.
+ *
+ * Only configure an RGMII TX (resp. RX) delay if the
+ * tx-internal-delay-ps (resp. rx-internal-delay-ps) OF property is
+ * specified. We ignore the detail of the RGMII interface mode
+ * (RGMII_{RXID, TXID, etc.}), as this is considered to be a PHY-only
+ * property.
+ */
+ if (!of_property_read_u32(dn, "tx-internal-delay-ps", &val)) {
+ val = val / 1000; /* convert to ns */
+
+ if (val == 0 || val == 2)
+ tx_delay = val / 2;
+ else
+ dev_warn(priv->dev,
+ "RGMII TX delay must be 0 or 2 ns\n");
+ }
+
+ if (!of_property_read_u32(dn, "rx-internal-delay-ps", &val)) {
+ val = DIV_ROUND_CLOSEST(val, 300); /* convert to 0.3 ns step */
+
+ if (val <= 7)
+ rx_delay = val;
+ else
+ dev_warn(priv->dev,
+ "RGMII RX delay must be 0 to 2.1 ns\n");
+ }
+
+ ret = regmap_update_bits(
+ priv->map, RTL8365MB_EXT_RGMXF_REG(extint->id),
+ RTL8365MB_EXT_RGMXF_TXDELAY_MASK |
+ RTL8365MB_EXT_RGMXF_RXDELAY_MASK,
+ FIELD_PREP(RTL8365MB_EXT_RGMXF_TXDELAY_MASK, tx_delay) |
+ FIELD_PREP(RTL8365MB_EXT_RGMXF_RXDELAY_MASK, rx_delay));
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(
+ priv->map, RTL8365MB_DIGITAL_INTERFACE_SELECT_REG(extint->id),
+ RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_MASK(extint->id),
+ RTL8365MB_EXT_PORT_MODE_RGMII
+ << RTL8365MB_DIGITAL_INTERFACE_SELECT_MODE_OFFSET(
+ extint->id));
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_ext_config_forcemode(struct realtek_priv *priv, int port,
+ bool link, int speed, int duplex,
+ bool tx_pause, bool rx_pause)
+{
+ const struct rtl8365mb_extint *extint =
+ rtl8365mb_get_port_extint(priv, port);
+ u32 r_tx_pause;
+ u32 r_rx_pause;
+ u32 r_duplex;
+ u32 r_speed;
+ u32 r_link;
+ int val;
+ int ret;
+
+ if (!extint)
+ return -ENODEV;
+
+ if (link) {
+ /* Force the link up with the desired configuration */
+ r_link = 1;
+ r_rx_pause = rx_pause ? 1 : 0;
+ r_tx_pause = tx_pause ? 1 : 0;
+
+ if (speed == SPEED_1000) {
+ r_speed = RTL8365MB_PORT_SPEED_1000M;
+ } else if (speed == SPEED_100) {
+ r_speed = RTL8365MB_PORT_SPEED_100M;
+ } else if (speed == SPEED_10) {
+ r_speed = RTL8365MB_PORT_SPEED_10M;
+ } else {
+ dev_err(priv->dev, "unsupported port speed %d\n",
+ speed);
+ dump_stack();
+ return -EINVAL;
+ }
+
+ if (duplex == DUPLEX_FULL) {
+ r_duplex = 1;
+ } else if (duplex == DUPLEX_HALF) {
+ r_duplex = 0;
+ } else {
+ dev_err(priv->dev, "unsupported duplex mode %d\n",
+ duplex);
+ return -EINVAL;
+ }
+ } else {
+ /* Force the link down and reset any programmed configuration */
+ r_link = 0;
+ r_tx_pause = 0;
+ r_rx_pause = 0;
+ r_speed = 0;
+ r_duplex = 0;
+ }
+
+ val = FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_EN_MASK, 1) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_TXPAUSE_MASK,
+ r_tx_pause) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_RXPAUSE_MASK,
+ r_rx_pause) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_LINK_MASK, r_link) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_DUPLEX_MASK,
+ r_duplex) |
+ FIELD_PREP(RTL8365MB_DIGITAL_INTERFACE_FORCE_SPEED_MASK, r_speed);
+ ret = regmap_write(priv->map,
+ RTL8365MB_DIGITAL_INTERFACE_FORCE_REG(extint->id),
+ val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void rtl8365mb_port_stp_state_set(struct dsa_switch *ds, int port,
+ u8 state)
+{
+ struct realtek_priv *priv = ds->priv;
+ enum rtl8365mb_stp_state val;
+ int msti = 0;
+
+ switch (state) {
+ case BR_STATE_DISABLED:
+ val = RTL8365MB_STP_STATE_DISABLED;
+ break;
+ case BR_STATE_FORWARDING:
+ val = RTL8365MB_STP_STATE_FORWARDING;
+ break;
+ default:
+ dev_err(priv->dev, "invalid STP state: %u\n", state);
+ return;
+ }
+
+ regmap_update_bits(priv->map, RTL8365MB_MSTI_CTRL_REG(msti, port),
+ RTL8365MB_MSTI_CTRL_PORT_STATE_MASK(port),
+ val << RTL8365MB_MSTI_CTRL_PORT_STATE_OFFSET(port));
+}
+
+static int rtl8365mb_phylink_mac_config(struct dsa_port *dp, int port,
+ phy_interface_t phy_mode)
+{
+ struct realtek_priv *priv = dp->ds->priv;
+ int ret = 0;
+
+ if (phy_interface_mode_is_rgmii(phy_mode)) {
+ ret = rtl8365mb_ext_config_rgmii(priv, port, phy_mode);
+ if (ret)
+ dev_err(priv->dev,
+ "failed to configure RGMII mode on port %d: %d\n",
+ port, ret);
+ }
+
+ return ret;
+}
+
+static void rtl8365mb_phylink_mac_link_down(struct dsa_port *dp, int port,
+ struct phy_device *phy)
+{
+ struct realtek_priv *priv = dp->ds->priv;
+ int ret;
+
+ rtl8365mb_port_stp_state_set(dp->ds, port, BR_STATE_DISABLED);
+
+ if (phy_interface_mode_is_rgmii(phy->interface)) {
+ ret = rtl8365mb_ext_config_forcemode(priv, port, false,
+ 0, 0, 0, 0);
+ if (ret)
+ dev_err(priv->dev,
+ "failed to reset forced mode on port %d: %d\n",
+ port, ret);
+ }
+}
+
+static int rtl8365mb_phylink_mac_link_up(struct dsa_port *dp, int port,
+ struct phy_device *phy)
+{
+ struct realtek_priv *priv = dp->ds->priv;
+ int ret = 0;
+
+ if (phy_interface_mode_is_rgmii(phy->interface)) {
+ ret = rtl8365mb_ext_config_forcemode(priv, port, true,
+ phy->speed, phy->duplex,
+ phy->pause, phy->pause);
+ if (ret)
+ dev_err(priv->dev,
+ "failed to force mode on port %d: %d\n", port,
+ ret);
+ }
+
+ rtl8365mb_port_stp_state_set(dp->ds, port, BR_STATE_FORWARDING);
+
+ return ret;
+}
+
+static int rtl8365mb_port_set_learning(struct realtek_priv *priv, int port,
+ bool enable)
+{
+ /* Enable/disable learning by limiting the number of L2 addresses the
+ * port can learn. Realtek documentation states that a limit of zero
+ * disables learning. When enabling learning, set it to the chip's
+ * maximum.
+ */
+ return regmap_write(priv->map, RTL8365MB_LUT_PORT_LEARN_LIMIT_REG(port),
+ enable ? RTL8365MB_LEARN_LIMIT_MAX : 0);
+}
+
+static int rtl8365mb_port_set_isolation(struct realtek_priv *priv, int port,
+ u32 mask)
+{
+ return regmap_write(priv->map, RTL8365MB_PORT_ISOLATION_REG(port), mask);
+}
+
+static int rtl8365mb_set_irq_enable(struct realtek_priv *priv, bool enable)
+{
+ return regmap_update_bits(priv->map, RTL8365MB_INTR_CTRL_REG,
+ RTL8365MB_INTR_LINK_CHANGE_MASK,
+ FIELD_PREP(RTL8365MB_INTR_LINK_CHANGE_MASK,
+ enable ? 1 : 0));
+}
+
+static int rtl8365mb_irq_disable(struct realtek_priv *priv)
+{
+ return rtl8365mb_set_irq_enable(priv, false);
+}
+
+static int rtl8365mb_irq_setup(struct realtek_priv *priv)
+{
+ int ret;
+
+ /* Disable the interrupt in case the chip has it enabled on reset */
+ ret = rtl8365mb_irq_disable(priv);
+ if (ret)
+ return ret;
+
+ /* Clear the interrupt status register */
+ return regmap_write(priv->map, RTL8365MB_INTR_STATUS_REG,
+ RTL8365MB_INTR_ALL_MASK);
+}
+
+static int rtl8365mb_cpu_config(struct realtek_priv *priv)
+{
+ struct rtl8365mb *mb = priv->chip_data;
+ struct rtl8365mb_cpu *cpu = &mb->cpu;
+ u32 val;
+ int ret;
+
+ ret = regmap_update_bits(priv->map, RTL8365MB_CPU_PORT_MASK_REG,
+ RTL8365MB_CPU_PORT_MASK_MASK,
+ FIELD_PREP(RTL8365MB_CPU_PORT_MASK_MASK,
+ cpu->mask));
+ if (ret)
+ return ret;
+
+ val = FIELD_PREP(RTL8365MB_CPU_CTRL_EN_MASK, 1) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_INSERTMODE_MASK, cpu->insert) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_POSITION_MASK, cpu->position) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_RXBYTECOUNT_MASK, cpu->rx_length) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TAG_FORMAT_MASK, cpu->format) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_MASK, cpu->trap_port & 0x7) |
+ FIELD_PREP(RTL8365MB_CPU_CTRL_TRAP_PORT_EXT_MASK,
+ cpu->trap_port >> 3 & 0x1);
+ ret = regmap_write(priv->map, RTL8365MB_CPU_CTRL_REG, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_change_tag_protocol(struct realtek_priv *priv,
+ enum dsa_tag_protocol proto)
+{
+ struct rtl8365mb_cpu *cpu;
+ struct rtl8365mb *mb;
+
+ mb = priv->chip_data;
+ cpu = &mb->cpu;
+
+ switch (proto) {
+ case DSA_TAG_PROTO_RTL8_4:
+ cpu->format = RTL8365MB_CPU_FORMAT_8BYTES;
+ cpu->position = RTL8365MB_CPU_POS_AFTER_SA;
+ break;
+ case DSA_TAG_PROTO_RTL8_4T:
+ cpu->format = RTL8365MB_CPU_FORMAT_8BYTES;
+ cpu->position = RTL8365MB_CPU_POS_BEFORE_CRC;
+ break;
+ /* The switch also supports a 4-byte format, similar to rtl4a but with
+ * the same 0x04 8-bit version and probably 8-bit port source/dest.
+ * There is no public doc about it. Not supported yet and it will probably
+ * never be.
+ */
+ default:
+ return -EPROTONOSUPPORT;
+ }
+
+ return rtl8365mb_cpu_config(priv);
+}
+
+static int rtl8365mb_switch_init(struct realtek_priv *priv)
+{
+ struct rtl8365mb *mb = priv->chip_data;
+ const struct rtl8365mb_chip_info *ci;
+ int ret;
+ int i;
+
+ ci = mb->chip_info;
+
+ /* Do any chip-specific init jam before getting to the common stuff */
+ if (ci->jam_table) {
+ for (i = 0; i < ci->jam_size; i++) {
+ ret = regmap_write(priv->map, ci->jam_table[i].reg,
+ ci->jam_table[i].val);
+ if (ret)
+ return ret;
+ }
+ }
+
+ /* Common init jam */
+ for (i = 0; i < ARRAY_SIZE(rtl8365mb_init_jam_common); i++) {
+ ret = regmap_write(priv->map, rtl8365mb_init_jam_common[i].reg,
+ rtl8365mb_init_jam_common[i].val);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rtl8365mb_reset_chip(struct realtek_priv *priv)
+{
+ u32 val;
+
+ priv->write_reg_noack(priv, RTL8365MB_CHIP_RESET_REG,
+ FIELD_PREP(RTL8365MB_CHIP_RESET_HW_MASK, 1));
+
+ /* Realtek documentation says the chip needs 1 second to reset. Sleep
+ * for 100 ms before accessing any registers to prevent ACK timeouts.
+ */
+ mdelay(100);
+ return regmap_read_poll_timeout(priv->map, RTL8365MB_CHIP_RESET_REG, val,
+ !(val & RTL8365MB_CHIP_RESET_HW_MASK),
+ 1e6);
+}
+
+static int rtl8365mb_setup(struct realtek_priv *priv)
+{
+ struct rtl8365mb_cpu *cpu;
+ struct dsa_port *cpu_dp;
+ struct rtl8365mb *mb;
+ int ret;
+ int i;
+
+ mb = priv->chip_data;
+ cpu = &mb->cpu;
+
+ ret = rtl8365mb_reset_chip(priv);
+ if (ret) {
+ dev_err(priv->dev, "failed to reset chip: %d\n", ret);
+ goto out_error;
+ }
+
+ /* Configure switch to vendor-defined initial state */
+ ret = rtl8365mb_switch_init(priv);
+ if (ret) {
+ dev_err(priv->dev, "failed to initialize switch: %d\n", ret);
+ goto out_error;
+ }
+
+ rtl8365mb_irq_setup(priv);
+
+ /* Configure CPU tagging */
+ dsa_switch_for_each_cpu_port(cpu_dp, priv->ds) {
+ cpu->mask |= BIT(cpu_dp->index);
+
+ if (cpu->trap_port == RTL8365MB_MAX_NUM_PORTS)
+ cpu->trap_port = cpu_dp->index;
+ }
+
+ if (cpu->mask == 0) {
+ dev_err(priv->dev, "no CPU port found\n");
+ goto out_teardown_irq;
+ }
+
+ ret = rtl8365mb_cpu_config(priv);
+ if (ret)
+ goto out_teardown_irq;
+
+ /* Configure ports */
+ for (i = 0; i < priv->num_ports; i++) {
+ struct rtl8365mb_port *p = &mb->ports[i];
+
+ /* Forward only to the CPU */
+ ret = rtl8365mb_port_set_isolation(priv, i, cpu->mask);
+ if (ret)
+ goto out_teardown_irq;
+
+ /* Disable learning */
+ ret = rtl8365mb_port_set_learning(priv, i, false);
+ if (ret)
+ goto out_teardown_irq;
+
+ /* Set the initial STP state of all ports to DISABLED, otherwise
+ * ports will still forward frames to the CPU despite being
+ * administratively down by default.
+ */
+ rtl8365mb_port_stp_state_set(priv->ds, i, BR_STATE_DISABLED);
+
+ /* Set up per-port private data */
+ p->priv = priv;
+ p->index = i;
+ }
+
+ /* Set maximum packet length to 1536 bytes */
+ ret = regmap_update_bits(priv->map, RTL8365MB_CFG0_MAX_LEN_REG,
+ RTL8365MB_CFG0_MAX_LEN_MASK,
+ FIELD_PREP(RTL8365MB_CFG0_MAX_LEN_MASK, 1536));
+ if (ret)
+ goto out_teardown_irq;
+
+ if (priv->setup_interface) {
+ ret = priv->setup_interface(priv->ds);
+ if (ret) {
+ dev_err(priv->dev, "could not set up MDIO bus\n");
+ goto out_teardown_irq;
+ }
+ }
+
+ return 0;
+
+out_teardown_irq:
+out_error:
+ return ret;
+}
+
+static int rtl8365mb_get_chip_id_and_ver(struct regmap *map, u32 *id, u32 *ver)
+{
+ int ret;
+
+ /* For some reason we have to write a magic value to an arbitrary
+ * register whenever accessing the chip ID/version registers.
+ */
+ ret = regmap_write(map, RTL8365MB_MAGIC_REG, RTL8365MB_MAGIC_VALUE);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(map, RTL8365MB_CHIP_ID_REG, id);
+ if (ret)
+ return ret;
+
+ ret = regmap_read(map, RTL8365MB_CHIP_VER_REG, ver);
+ if (ret)
+ return ret;
+
+ /* Reset magic register */
+ ret = regmap_write(map, RTL8365MB_MAGIC_REG, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtl8365mb_detect(struct realtek_priv *priv)
+{
+ struct rtl8365mb *mb = priv->chip_data;
+ u32 chip_id;
+ u32 chip_ver;
+ int ret;
+ int i;
+
+ ret = rtl8365mb_get_chip_id_and_ver(priv->map, &chip_id, &chip_ver);
+ if (ret) {
+ dev_err(priv->dev, "failed to read chip id and version: %d\n",
+ ret);
+ return ret;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(rtl8365mb_chip_infos); i++) {
+ const struct rtl8365mb_chip_info *ci = &rtl8365mb_chip_infos[i];
+
+ if (ci->chip_id == chip_id && ci->chip_ver == chip_ver) {
+ mb->chip_info = ci;
+ break;
+ }
+ }
+
+ if (!mb->chip_info) {
+ dev_err(priv->dev,
+ "unrecognized switch (id=0x%04x, ver=0x%04x)", chip_id,
+ chip_ver);
+ return -ENODEV;
+ }
+
+ dev_info(priv->dev, "found an %s switch\n", mb->chip_info->name);
+
+ priv->num_ports = RTL8365MB_MAX_NUM_PORTS;
+ mb->priv = priv;
+ mb->cpu.trap_port = RTL8365MB_MAX_NUM_PORTS;
+ mb->cpu.insert = RTL8365MB_CPU_INSERT_TO_ALL;
+ mb->cpu.position = RTL8365MB_CPU_POS_AFTER_SA;
+ mb->cpu.rx_length = RTL8365MB_CPU_RXLEN_64BYTES;
+ mb->cpu.format = RTL8365MB_CPU_FORMAT_8BYTES;
+
+ return 0;
+}
+
+static const struct dsa_switch_ops rtl8365mb_switch_ops_smi = {
+ .port_pre_enable = rtl8365mb_phylink_mac_config,
+ .port_disable = rtl8365mb_phylink_mac_link_down,
+ .port_enable = rtl8365mb_phylink_mac_link_up,
+};
+
+static const struct dsa_switch_ops rtl8365mb_switch_ops_mdio = {
+ .port_pre_enable = rtl8365mb_phylink_mac_config,
+ .port_disable = rtl8365mb_phylink_mac_link_down,
+ .port_enable = rtl8365mb_phylink_mac_link_up,
+ .phy_read = rtl8365mb_dsa_phy_read,
+ .phy_write = rtl8365mb_dsa_phy_write,
+};
+
+static const struct realtek_ops rtl8365mb_ops = {
+ .detect = rtl8365mb_detect,
+ .phy_read = rtl8365mb_phy_read,
+ .phy_write = rtl8365mb_phy_write,
+ .setup = rtl8365mb_setup,
+ .get_tag_protocol = rtl8365mb_get_tag_protocol,
+ .change_tag_protocol = rtl8365mb_change_tag_protocol,
+};
+
+const struct realtek_variant rtl8365mb_variant = {
+ .ds_ops_smi = &rtl8365mb_switch_ops_smi,
+ .ds_ops_mdio = &rtl8365mb_switch_ops_mdio,
+ .ops = &rtl8365mb_ops,
+ .clk_delay = 10,
+ .cmd_read = 0xb9,
+ .cmd_write = 0xb8,
+ .chip_data_sz = sizeof(struct rtl8365mb),
+};
+EXPORT_SYMBOL_GPL(rtl8365mb_variant);
+
+MODULE_AUTHOR("Alvin Šipraga <alsi@bang-olufsen.dk>");
+MODULE_DESCRIPTION("Driver for RTL8365MB-VC ethernet switch");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/realtek-dsa/rtl8366rb.c b/drivers/net/realtek-dsa/rtl8366rb.c
new file mode 100644
index 000000000000..67dcb7fb704f
--- /dev/null
+++ b/drivers/net/realtek-dsa/rtl8366rb.c
@@ -0,0 +1,1123 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Realtek SMI subdriver for the Realtek RTL8366RB ethernet switch
+ *
+ * This is a sparsely documented chip, the only viable documentation seems
+ * to be a patched up code drop from the vendor that appear in various
+ * GPL source trees.
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2010 Antti Seppälä <a.seppala@gmail.com>
+ * Copyright (C) 2010 Roman Yeryomin <roman@advem.lv>
+ * Copyright (C) 2011 Colin Leitner <colin.leitner@googlemail.com>
+ */
+
+#include <linux/bitops.h>
+#include <net.h>
+#include <linux/if_bridge.h>
+#include <regmap.h>
+
+#include "realtek.h"
+
+#define RTL8366RB_PORT_NUM_CPU 5
+#define RTL8366RB_NUM_PORTS 6
+#define RTL8366RB_PHY_NO_MAX 4
+#define RTL8366RB_PHY_ADDR_MAX 31
+
+/* Switch Global Configuration register */
+#define RTL8366RB_SGCR 0x0000
+#define RTL8366RB_SGCR_EN_BC_STORM_CTRL BIT(0)
+#define RTL8366RB_SGCR_MAX_LENGTH(a) ((a) << 4)
+#define RTL8366RB_SGCR_MAX_LENGTH_MASK RTL8366RB_SGCR_MAX_LENGTH(0x3)
+#define RTL8366RB_SGCR_MAX_LENGTH_1522 RTL8366RB_SGCR_MAX_LENGTH(0x0)
+#define RTL8366RB_SGCR_MAX_LENGTH_1536 RTL8366RB_SGCR_MAX_LENGTH(0x1)
+#define RTL8366RB_SGCR_MAX_LENGTH_1552 RTL8366RB_SGCR_MAX_LENGTH(0x2)
+#define RTL8366RB_SGCR_MAX_LENGTH_16000 RTL8366RB_SGCR_MAX_LENGTH(0x3)
+#define RTL8366RB_SGCR_EN_VLAN BIT(13)
+#define RTL8366RB_SGCR_EN_VLAN_4KTB BIT(14)
+
+/* Port Enable Control register */
+#define RTL8366RB_PECR 0x0001
+
+/* Switch per-port learning disablement register */
+#define RTL8366RB_PORT_LEARNDIS_CTRL 0x0002
+
+/* Security control, actually aging register */
+#define RTL8366RB_SECURITY_CTRL 0x0003
+
+#define RTL8366RB_SSCR2 0x0004
+#define RTL8366RB_SSCR2_DROP_UNKNOWN_DA BIT(0)
+
+/* Port Mode Control registers */
+#define RTL8366RB_PMC0 0x0005
+#define RTL8366RB_PMC0_SPI BIT(0)
+#define RTL8366RB_PMC0_EN_AUTOLOAD BIT(1)
+#define RTL8366RB_PMC0_PROBE BIT(2)
+#define RTL8366RB_PMC0_DIS_BISR BIT(3)
+#define RTL8366RB_PMC0_ADCTEST BIT(4)
+#define RTL8366RB_PMC0_SRAM_DIAG BIT(5)
+#define RTL8366RB_PMC0_EN_SCAN BIT(6)
+#define RTL8366RB_PMC0_P4_IOMODE_SHIFT 7
+#define RTL8366RB_PMC0_P4_IOMODE_MASK GENMASK(9, 7)
+#define RTL8366RB_PMC0_P5_IOMODE_SHIFT 10
+#define RTL8366RB_PMC0_P5_IOMODE_MASK GENMASK(12, 10)
+#define RTL8366RB_PMC0_SDSMODE_SHIFT 13
+#define RTL8366RB_PMC0_SDSMODE_MASK GENMASK(15, 13)
+#define RTL8366RB_PMC1 0x0006
+
+/* Port Mirror Control Register */
+#define RTL8366RB_PMCR 0x0007
+#define RTL8366RB_PMCR_SOURCE_PORT(a) (a)
+#define RTL8366RB_PMCR_SOURCE_PORT_MASK 0x000f
+#define RTL8366RB_PMCR_MONITOR_PORT(a) ((a) << 4)
+#define RTL8366RB_PMCR_MONITOR_PORT_MASK 0x00f0
+#define RTL8366RB_PMCR_MIRROR_RX BIT(8)
+#define RTL8366RB_PMCR_MIRROR_TX BIT(9)
+#define RTL8366RB_PMCR_MIRROR_SPC BIT(10)
+#define RTL8366RB_PMCR_MIRROR_ISO BIT(11)
+
+/* bits 0..7 = port 0, bits 8..15 = port 1 */
+#define RTL8366RB_PAACR0 0x0010
+/* bits 0..7 = port 2, bits 8..15 = port 3 */
+#define RTL8366RB_PAACR1 0x0011
+/* bits 0..7 = port 4, bits 8..15 = port 5 */
+#define RTL8366RB_PAACR2 0x0012
+#define RTL8366RB_PAACR_SPEED_10M 0
+#define RTL8366RB_PAACR_SPEED_100M 1
+#define RTL8366RB_PAACR_SPEED_1000M 2
+#define RTL8366RB_PAACR_FULL_DUPLEX BIT(2)
+#define RTL8366RB_PAACR_LINK_UP BIT(4)
+#define RTL8366RB_PAACR_TX_PAUSE BIT(5)
+#define RTL8366RB_PAACR_RX_PAUSE BIT(6)
+#define RTL8366RB_PAACR_AN BIT(7)
+
+#define RTL8366RB_PAACR_CPU_PORT (RTL8366RB_PAACR_SPEED_1000M | \
+ RTL8366RB_PAACR_FULL_DUPLEX | \
+ RTL8366RB_PAACR_LINK_UP | \
+ RTL8366RB_PAACR_TX_PAUSE | \
+ RTL8366RB_PAACR_RX_PAUSE)
+
+/* bits 0..7 = port 0, bits 8..15 = port 1 */
+#define RTL8366RB_PSTAT0 0x0014
+/* bits 0..7 = port 2, bits 8..15 = port 3 */
+#define RTL8366RB_PSTAT1 0x0015
+/* bits 0..7 = port 4, bits 8..15 = port 5 */
+#define RTL8366RB_PSTAT2 0x0016
+
+#define RTL8366RB_POWER_SAVING_REG 0x0021
+
+/* Spanning tree status (STP) control, two bits per port per FID */
+#define RTL8366RB_STP_STATE_BASE 0x0050 /* 0x0050..0x0057 */
+#define RTL8366RB_STP_STATE_DISABLED 0x0
+#define RTL8366RB_STP_STATE_BLOCKING 0x1
+#define RTL8366RB_STP_STATE_LEARNING 0x2
+#define RTL8366RB_STP_STATE_FORWARDING 0x3
+#define RTL8366RB_STP_MASK GENMASK(1, 0)
+#define RTL8366RB_STP_STATE(port, state) \
+ ((state) << ((port) * 2))
+#define RTL8366RB_STP_STATE_MASK(port) \
+ RTL8366RB_STP_STATE((port), RTL8366RB_STP_MASK)
+
+/* CPU port control reg */
+#define RTL8368RB_CPU_CTRL_REG 0x0061
+#define RTL8368RB_CPU_PORTS_MSK 0x00FF
+/* Disables inserting custom tag length/type 0x8899 */
+#define RTL8368RB_CPU_NO_TAG BIT(15)
+
+#define RTL8366RB_SMAR0 0x0070 /* bits 0..15 */
+#define RTL8366RB_SMAR1 0x0071 /* bits 16..31 */
+#define RTL8366RB_SMAR2 0x0072 /* bits 32..47 */
+
+#define RTL8366RB_RESET_CTRL_REG 0x0100
+#define RTL8366RB_CHIP_CTRL_RESET_HW BIT(0)
+#define RTL8366RB_CHIP_CTRL_RESET_SW BIT(1)
+
+#define RTL8366RB_CHIP_ID_REG 0x0509
+#define RTL8366RB_CHIP_ID_8366 0x5937
+#define RTL8366RB_CHIP_VERSION_CTRL_REG 0x050A
+#define RTL8366RB_CHIP_VERSION_MASK 0xf
+
+/* PHY registers control */
+#define RTL8366RB_PHY_ACCESS_CTRL_REG 0x8000
+#define RTL8366RB_PHY_CTRL_READ BIT(0)
+#define RTL8366RB_PHY_CTRL_WRITE 0
+#define RTL8366RB_PHY_ACCESS_BUSY_REG 0x8001
+#define RTL8366RB_PHY_INT_BUSY BIT(0)
+#define RTL8366RB_PHY_EXT_BUSY BIT(4)
+#define RTL8366RB_PHY_ACCESS_DATA_REG 0x8002
+#define RTL8366RB_PHY_EXT_CTRL_REG 0x8010
+#define RTL8366RB_PHY_EXT_WRDATA_REG 0x8011
+#define RTL8366RB_PHY_EXT_RDDATA_REG 0x8012
+
+#define RTL8366RB_PHY_REG_MASK 0x1f
+#define RTL8366RB_PHY_PAGE_OFFSET 5
+#define RTL8366RB_PHY_PAGE_MASK (0xf << 5)
+#define RTL8366RB_PHY_NO_OFFSET 9
+#define RTL8366RB_PHY_NO_MASK (0x1f << 9)
+
+/* VLAN Ingress Control Register 1, one bit per port.
+ * bit 0 .. 5 will make the switch drop ingress frames without
+ * VID such as untagged or priority-tagged frames for respective
+ * port.
+ * bit 6 .. 11 will make the switch drop ingress frames carrying
+ * a C-tag with VID != 0 for respective port.
+ */
+#define RTL8366RB_VLAN_INGRESS_CTRL1_REG 0x037E
+#define RTL8366RB_VLAN_INGRESS_CTRL1_DROP(port) (BIT((port)) | BIT((port) + 6))
+
+/* VLAN Ingress Control Register 2, one bit per port.
+ * bit0 .. bit5 will make the switch drop all ingress frames with
+ * a VLAN classification that does not include the port is in its
+ * member set.
+ */
+#define RTL8366RB_VLAN_INGRESS_CTRL2_REG 0x037f
+
+/* LED control registers */
+#define RTL8366RB_LED_BLINKRATE_REG 0x0430
+#define RTL8366RB_LED_BLINKRATE_MASK 0x0007
+#define RTL8366RB_LED_BLINKRATE_28MS 0x0000
+#define RTL8366RB_LED_BLINKRATE_56MS 0x0001
+#define RTL8366RB_LED_BLINKRATE_84MS 0x0002
+#define RTL8366RB_LED_BLINKRATE_111MS 0x0003
+#define RTL8366RB_LED_BLINKRATE_222MS 0x0004
+#define RTL8366RB_LED_BLINKRATE_446MS 0x0005
+
+#define RTL8366RB_LED_CTRL_REG 0x0431
+#define RTL8366RB_LED_OFF 0x0
+#define RTL8366RB_LED_DUP_COL 0x1
+#define RTL8366RB_LED_LINK_ACT 0x2
+#define RTL8366RB_LED_SPD1000 0x3
+#define RTL8366RB_LED_SPD100 0x4
+#define RTL8366RB_LED_SPD10 0x5
+#define RTL8366RB_LED_SPD1000_ACT 0x6
+#define RTL8366RB_LED_SPD100_ACT 0x7
+#define RTL8366RB_LED_SPD10_ACT 0x8
+#define RTL8366RB_LED_SPD100_10_ACT 0x9
+#define RTL8366RB_LED_FIBER 0xa
+#define RTL8366RB_LED_AN_FAULT 0xb
+#define RTL8366RB_LED_LINK_RX 0xc
+#define RTL8366RB_LED_LINK_TX 0xd
+#define RTL8366RB_LED_MASTER 0xe
+#define RTL8366RB_LED_FORCE 0xf
+#define RTL8366RB_LED_0_1_CTRL_REG 0x0432
+#define RTL8366RB_LED_1_OFFSET 6
+#define RTL8366RB_LED_2_3_CTRL_REG 0x0433
+#define RTL8366RB_LED_3_OFFSET 6
+
+#define RTL8366RB_PORT_VLAN_CTRL_BASE 0x0063
+#define RTL8366RB_PORT_VLAN_CTRL_REG(_p) \
+ (RTL8366RB_PORT_VLAN_CTRL_BASE + (_p) / 4)
+#define RTL8366RB_PORT_VLAN_CTRL_MASK 0xf
+#define RTL8366RB_PORT_VLAN_CTRL_SHIFT(_p) (4 * ((_p) % 4))
+
+#define RTL8366RB_VLAN_TABLE_READ_BASE 0x018C
+#define RTL8366RB_VLAN_TABLE_WRITE_BASE 0x0185
+
+#define RTL8366RB_TABLE_ACCESS_CTRL_REG 0x0180
+#define RTL8366RB_TABLE_VLAN_READ_CTRL 0x0E01
+#define RTL8366RB_TABLE_VLAN_WRITE_CTRL 0x0F01
+
+#define RTL8366RB_VLAN_MC_BASE(_x) (0x0020 + (_x) * 3)
+
+#define RTL8366RB_PORT_LINK_STATUS_BASE 0x0014
+#define RTL8366RB_PORT_STATUS_SPEED_MASK 0x0003
+#define RTL8366RB_PORT_STATUS_DUPLEX_MASK 0x0004
+#define RTL8366RB_PORT_STATUS_LINK_MASK 0x0010
+#define RTL8366RB_PORT_STATUS_TXPAUSE_MASK 0x0020
+#define RTL8366RB_PORT_STATUS_RXPAUSE_MASK 0x0040
+#define RTL8366RB_PORT_STATUS_AN_MASK 0x0080
+
+#define RTL8366RB_NUM_VLANS 16
+#define RTL8366RB_NUM_LEDGROUPS 4
+#define RTL8366RB_NUM_VIDS 4096
+#define RTL8366RB_PRIORITYMAX 7
+#define RTL8366RB_NUM_FIDS 8
+#define RTL8366RB_FIDMAX 7
+
+#define RTL8366RB_PORT_1 BIT(0) /* In userspace port 0 */
+#define RTL8366RB_PORT_2 BIT(1) /* In userspace port 1 */
+#define RTL8366RB_PORT_3 BIT(2) /* In userspace port 2 */
+#define RTL8366RB_PORT_4 BIT(3) /* In userspace port 3 */
+#define RTL8366RB_PORT_5 BIT(4) /* In userspace port 4 */
+
+#define RTL8366RB_PORT_CPU BIT(5) /* CPU port */
+
+#define RTL8366RB_PORT_ALL (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4 | \
+ RTL8366RB_PORT_5 | \
+ RTL8366RB_PORT_CPU)
+
+#define RTL8366RB_PORT_ALL_BUT_CPU (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4 | \
+ RTL8366RB_PORT_5)
+
+#define RTL8366RB_PORT_ALL_EXTERNAL (RTL8366RB_PORT_1 | \
+ RTL8366RB_PORT_2 | \
+ RTL8366RB_PORT_3 | \
+ RTL8366RB_PORT_4)
+
+#define RTL8366RB_PORT_ALL_INTERNAL RTL8366RB_PORT_CPU
+
+/* First configuration word per member config, VID and prio */
+#define RTL8366RB_VLAN_VID_MASK 0xfff
+#define RTL8366RB_VLAN_PRIORITY_SHIFT 12
+#define RTL8366RB_VLAN_PRIORITY_MASK 0x7
+/* Second configuration word per member config, member and untagged */
+#define RTL8366RB_VLAN_UNTAG_SHIFT 8
+#define RTL8366RB_VLAN_UNTAG_MASK 0xff
+#define RTL8366RB_VLAN_MEMBER_MASK 0xff
+/* Third config word per member config, STAG currently unused */
+#define RTL8366RB_VLAN_STAG_MBR_MASK 0xff
+#define RTL8366RB_VLAN_STAG_MBR_SHIFT 8
+#define RTL8366RB_VLAN_STAG_IDX_MASK 0x7
+#define RTL8366RB_VLAN_STAG_IDX_SHIFT 5
+#define RTL8366RB_VLAN_FID_MASK 0x7
+
+/* Port ingress bandwidth control */
+#define RTL8366RB_IB_BASE 0x0200
+#define RTL8366RB_IB_REG(pnum) (RTL8366RB_IB_BASE + (pnum))
+#define RTL8366RB_IB_BDTH_MASK 0x3fff
+#define RTL8366RB_IB_PREIFG BIT(14)
+
+/* Port egress bandwidth control */
+#define RTL8366RB_EB_BASE 0x02d1
+#define RTL8366RB_EB_REG(pnum) (RTL8366RB_EB_BASE + (pnum))
+#define RTL8366RB_EB_BDTH_MASK 0x3fff
+#define RTL8366RB_EB_PREIFG_REG 0x02f8
+#define RTL8366RB_EB_PREIFG BIT(9)
+
+#define RTL8366RB_BDTH_SW_MAX 1048512 /* 1048576? */
+#define RTL8366RB_BDTH_UNIT 64
+#define RTL8366RB_BDTH_REG_DEFAULT 16383
+
+/* QOS */
+#define RTL8366RB_QOS BIT(15)
+/* Include/Exclude Preamble and IFG (20 bytes). 0:Exclude, 1:Include. */
+#define RTL8366RB_QOS_DEFAULT_PREIFG 1
+
+/* Interrupt handling */
+#define RTL8366RB_INTERRUPT_CONTROL_REG 0x0440
+#define RTL8366RB_INTERRUPT_POLARITY BIT(0)
+#define RTL8366RB_P4_RGMII_LED BIT(2)
+#define RTL8366RB_INTERRUPT_MASK_REG 0x0441
+#define RTL8366RB_INTERRUPT_LINK_CHGALL GENMASK(11, 0)
+#define RTL8366RB_INTERRUPT_ACLEXCEED BIT(8)
+#define RTL8366RB_INTERRUPT_STORMEXCEED BIT(9)
+#define RTL8366RB_INTERRUPT_P4_FIBER BIT(12)
+#define RTL8366RB_INTERRUPT_P4_UTP BIT(13)
+#define RTL8366RB_INTERRUPT_VALID (RTL8366RB_INTERRUPT_LINK_CHGALL | \
+ RTL8366RB_INTERRUPT_ACLEXCEED | \
+ RTL8366RB_INTERRUPT_STORMEXCEED | \
+ RTL8366RB_INTERRUPT_P4_FIBER | \
+ RTL8366RB_INTERRUPT_P4_UTP)
+#define RTL8366RB_INTERRUPT_STATUS_REG 0x0442
+#define RTL8366RB_NUM_INTERRUPT 14 /* 0..13 */
+
+/* Port isolation registers */
+#define RTL8366RB_PORT_ISO_BASE 0x0F08
+#define RTL8366RB_PORT_ISO(pnum) (RTL8366RB_PORT_ISO_BASE + (pnum))
+#define RTL8366RB_PORT_ISO_EN BIT(0)
+#define RTL8366RB_PORT_ISO_PORTS_MASK GENMASK(7, 1)
+#define RTL8366RB_PORT_ISO_PORTS(pmask) ((pmask) << 1)
+
+/* bits 0..5 enable force when cleared */
+#define RTL8366RB_MAC_FORCE_CTRL_REG 0x0F11
+
+#define RTL8366RB_OAM_PARSER_REG 0x0F14
+#define RTL8366RB_OAM_MULTIPLEXER_REG 0x0F15
+
+#define RTL8366RB_GREEN_FEATURE_REG 0x0F51
+#define RTL8366RB_GREEN_FEATURE_MSK 0x0007
+#define RTL8366RB_GREEN_FEATURE_TX BIT(0)
+#define RTL8366RB_GREEN_FEATURE_RX BIT(2)
+
+static void rtl8366rb_mask_irqs(struct realtek_priv *priv)
+{
+ int ret;
+
+ ret = regmap_write(priv->map, RTL8366RB_INTERRUPT_MASK_REG, 0);
+ if (ret)
+ dev_err(priv->dev, "could not mask IRQ\n");
+}
+
+static int rtl8366rb_irq_setup(struct realtek_priv *priv)
+{
+ int ret;
+ u32 val;
+
+ rtl8366rb_mask_irqs(priv);
+
+ /* This clears the IRQ status register */
+ ret = regmap_read(priv->map, RTL8366RB_INTERRUPT_STATUS_REG,
+ &val);
+ if (ret)
+ dev_err(priv->dev, "can't read interrupt status\n");
+
+ return ret;
+}
+
+static int rtl8366rb_set_addr(struct realtek_priv *priv)
+{
+ u8 addr[ETH_ALEN];
+ u16 val;
+ int ret;
+
+ random_ether_addr(addr);
+
+ dev_info(priv->dev, "set MAC: %02X:%02X:%02X:%02X:%02X:%02X\n",
+ addr[0], addr[1], addr[2], addr[3], addr[4], addr[5]);
+ val = addr[0] << 8 | addr[1];
+ ret = regmap_write(priv->map, RTL8366RB_SMAR0, val);
+ if (ret)
+ return ret;
+ val = addr[2] << 8 | addr[3];
+ ret = regmap_write(priv->map, RTL8366RB_SMAR1, val);
+ if (ret)
+ return ret;
+ val = addr[4] << 8 | addr[5];
+ ret = regmap_write(priv->map, RTL8366RB_SMAR2, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+/* Found in a vendor driver */
+
+/* Struct for handling the jam tables' entries */
+struct rtl8366rb_jam_tbl_entry {
+ u16 reg;
+ u16 val;
+};
+
+/* For the "version 0" early silicon, appear in most source releases */
+static const struct rtl8366rb_jam_tbl_entry rtl8366rb_init_jam_ver_0[] = {
+ {0x000B, 0x0001}, {0x03A6, 0x0100}, {0x03A7, 0x0001}, {0x02D1, 0x3FFF},
+ {0x02D2, 0x3FFF}, {0x02D3, 0x3FFF}, {0x02D4, 0x3FFF}, {0x02D5, 0x3FFF},
+ {0x02D6, 0x3FFF}, {0x02D7, 0x3FFF}, {0x02D8, 0x3FFF}, {0x022B, 0x0688},
+ {0x022C, 0x0FAC}, {0x03D0, 0x4688}, {0x03D1, 0x01F5}, {0x0000, 0x0830},
+ {0x02F9, 0x0200}, {0x02F7, 0x7FFF}, {0x02F8, 0x03FF}, {0x0080, 0x03E8},
+ {0x0081, 0x00CE}, {0x0082, 0x00DA}, {0x0083, 0x0230}, {0xBE0F, 0x2000},
+ {0x0231, 0x422A}, {0x0232, 0x422A}, {0x0233, 0x422A}, {0x0234, 0x422A},
+ {0x0235, 0x422A}, {0x0236, 0x422A}, {0x0237, 0x422A}, {0x0238, 0x422A},
+ {0x0239, 0x422A}, {0x023A, 0x422A}, {0x023B, 0x422A}, {0x023C, 0x422A},
+ {0x023D, 0x422A}, {0x023E, 0x422A}, {0x023F, 0x422A}, {0x0240, 0x422A},
+ {0x0241, 0x422A}, {0x0242, 0x422A}, {0x0243, 0x422A}, {0x0244, 0x422A},
+ {0x0245, 0x422A}, {0x0246, 0x422A}, {0x0247, 0x422A}, {0x0248, 0x422A},
+ {0x0249, 0x0146}, {0x024A, 0x0146}, {0x024B, 0x0146}, {0xBE03, 0xC961},
+ {0x024D, 0x0146}, {0x024E, 0x0146}, {0x024F, 0x0146}, {0x0250, 0x0146},
+ {0xBE64, 0x0226}, {0x0252, 0x0146}, {0x0253, 0x0146}, {0x024C, 0x0146},
+ {0x0251, 0x0146}, {0x0254, 0x0146}, {0xBE62, 0x3FD0}, {0x0084, 0x0320},
+ {0x0255, 0x0146}, {0x0256, 0x0146}, {0x0257, 0x0146}, {0x0258, 0x0146},
+ {0x0259, 0x0146}, {0x025A, 0x0146}, {0x025B, 0x0146}, {0x025C, 0x0146},
+ {0x025D, 0x0146}, {0x025E, 0x0146}, {0x025F, 0x0146}, {0x0260, 0x0146},
+ {0x0261, 0xA23F}, {0x0262, 0x0294}, {0x0263, 0xA23F}, {0x0264, 0x0294},
+ {0x0265, 0xA23F}, {0x0266, 0x0294}, {0x0267, 0xA23F}, {0x0268, 0x0294},
+ {0x0269, 0xA23F}, {0x026A, 0x0294}, {0x026B, 0xA23F}, {0x026C, 0x0294},
+ {0x026D, 0xA23F}, {0x026E, 0x0294}, {0x026F, 0xA23F}, {0x0270, 0x0294},
+ {0x02F5, 0x0048}, {0xBE09, 0x0E00}, {0xBE1E, 0x0FA0}, {0xBE14, 0x8448},
+ {0xBE15, 0x1007}, {0xBE4A, 0xA284}, {0xC454, 0x3F0B}, {0xC474, 0x3F0B},
+ {0xBE48, 0x3672}, {0xBE4B, 0x17A7}, {0xBE4C, 0x0B15}, {0xBE52, 0x0EDD},
+ {0xBE49, 0x8C00}, {0xBE5B, 0x785C}, {0xBE5C, 0x785C}, {0xBE5D, 0x785C},
+ {0xBE61, 0x368A}, {0xBE63, 0x9B84}, {0xC456, 0xCC13}, {0xC476, 0xCC13},
+ {0xBE65, 0x307D}, {0xBE6D, 0x0005}, {0xBE6E, 0xE120}, {0xBE2E, 0x7BAF},
+};
+
+/* This v1 init sequence is from Belkin F5D8235 U-Boot release */
+static const struct rtl8366rb_jam_tbl_entry rtl8366rb_init_jam_ver_1[] = {
+ {0x0000, 0x0830}, {0x0001, 0x8000}, {0x0400, 0x8130}, {0xBE78, 0x3C3C},
+ {0x0431, 0x5432}, {0xBE37, 0x0CE4}, {0x02FA, 0xFFDF}, {0x02FB, 0xFFE0},
+ {0xC44C, 0x1585}, {0xC44C, 0x1185}, {0xC44C, 0x1585}, {0xC46C, 0x1585},
+ {0xC46C, 0x1185}, {0xC46C, 0x1585}, {0xC451, 0x2135}, {0xC471, 0x2135},
+ {0xBE10, 0x8140}, {0xBE15, 0x0007}, {0xBE6E, 0xE120}, {0xBE69, 0xD20F},
+ {0xBE6B, 0x0320}, {0xBE24, 0xB000}, {0xBE23, 0xFF51}, {0xBE22, 0xDF20},
+ {0xBE21, 0x0140}, {0xBE20, 0x00BB}, {0xBE24, 0xB800}, {0xBE24, 0x0000},
+ {0xBE24, 0x7000}, {0xBE23, 0xFF51}, {0xBE22, 0xDF60}, {0xBE21, 0x0140},
+ {0xBE20, 0x0077}, {0xBE24, 0x7800}, {0xBE24, 0x0000}, {0xBE2E, 0x7B7A},
+ {0xBE36, 0x0CE4}, {0x02F5, 0x0048}, {0xBE77, 0x2940}, {0x000A, 0x83E0},
+ {0xBE79, 0x3C3C}, {0xBE00, 0x1340},
+};
+
+/* This v2 init sequence is from Belkin F5D8235 U-Boot release */
+static const struct rtl8366rb_jam_tbl_entry rtl8366rb_init_jam_ver_2[] = {
+ {0x0450, 0x0000}, {0x0400, 0x8130}, {0x000A, 0x83ED}, {0x0431, 0x5432},
+ {0xC44F, 0x6250}, {0xC46F, 0x6250}, {0xC456, 0x0C14}, {0xC476, 0x0C14},
+ {0xC44C, 0x1C85}, {0xC44C, 0x1885}, {0xC44C, 0x1C85}, {0xC46C, 0x1C85},
+ {0xC46C, 0x1885}, {0xC46C, 0x1C85}, {0xC44C, 0x0885}, {0xC44C, 0x0881},
+ {0xC44C, 0x0885}, {0xC46C, 0x0885}, {0xC46C, 0x0881}, {0xC46C, 0x0885},
+ {0xBE2E, 0x7BA7}, {0xBE36, 0x1000}, {0xBE37, 0x1000}, {0x8000, 0x0001},
+ {0xBE69, 0xD50F}, {0x8000, 0x0000}, {0xBE69, 0xD50F}, {0xBE6E, 0x0320},
+ {0xBE77, 0x2940}, {0xBE78, 0x3C3C}, {0xBE79, 0x3C3C}, {0xBE6E, 0xE120},
+ {0x8000, 0x0001}, {0xBE15, 0x1007}, {0x8000, 0x0000}, {0xBE15, 0x1007},
+ {0xBE14, 0x0448}, {0xBE1E, 0x00A0}, {0xBE10, 0x8160}, {0xBE10, 0x8140},
+ {0xBE00, 0x1340}, {0x0F51, 0x0010},
+};
+
+/* Appears in a DDWRT code dump */
+static const struct rtl8366rb_jam_tbl_entry rtl8366rb_init_jam_ver_3[] = {
+ {0x0000, 0x0830}, {0x0400, 0x8130}, {0x000A, 0x83ED}, {0x0431, 0x5432},
+ {0x0F51, 0x0017}, {0x02F5, 0x0048}, {0x02FA, 0xFFDF}, {0x02FB, 0xFFE0},
+ {0xC456, 0x0C14}, {0xC476, 0x0C14}, {0xC454, 0x3F8B}, {0xC474, 0x3F8B},
+ {0xC450, 0x2071}, {0xC470, 0x2071}, {0xC451, 0x226B}, {0xC471, 0x226B},
+ {0xC452, 0xA293}, {0xC472, 0xA293}, {0xC44C, 0x1585}, {0xC44C, 0x1185},
+ {0xC44C, 0x1585}, {0xC46C, 0x1585}, {0xC46C, 0x1185}, {0xC46C, 0x1585},
+ {0xC44C, 0x0185}, {0xC44C, 0x0181}, {0xC44C, 0x0185}, {0xC46C, 0x0185},
+ {0xC46C, 0x0181}, {0xC46C, 0x0185}, {0xBE24, 0xB000}, {0xBE23, 0xFF51},
+ {0xBE22, 0xDF20}, {0xBE21, 0x0140}, {0xBE20, 0x00BB}, {0xBE24, 0xB800},
+ {0xBE24, 0x0000}, {0xBE24, 0x7000}, {0xBE23, 0xFF51}, {0xBE22, 0xDF60},
+ {0xBE21, 0x0140}, {0xBE20, 0x0077}, {0xBE24, 0x7800}, {0xBE24, 0x0000},
+ {0xBE2E, 0x7BA7}, {0xBE36, 0x1000}, {0xBE37, 0x1000}, {0x8000, 0x0001},
+ {0xBE69, 0xD50F}, {0x8000, 0x0000}, {0xBE69, 0xD50F}, {0xBE6B, 0x0320},
+ {0xBE77, 0x2800}, {0xBE78, 0x3C3C}, {0xBE79, 0x3C3C}, {0xBE6E, 0xE120},
+ {0x8000, 0x0001}, {0xBE10, 0x8140}, {0x8000, 0x0000}, {0xBE10, 0x8140},
+ {0xBE15, 0x1007}, {0xBE14, 0x0448}, {0xBE1E, 0x00A0}, {0xBE10, 0x8160},
+ {0xBE10, 0x8140}, {0xBE00, 0x1340}, {0x0450, 0x0000}, {0x0401, 0x0000},
+};
+
+/* Belkin F5D8235 v1, "belkin,f5d8235-v1" */
+static const struct rtl8366rb_jam_tbl_entry rtl8366rb_init_jam_f5d8235[] = {
+ {0x0242, 0x02BF}, {0x0245, 0x02BF}, {0x0248, 0x02BF}, {0x024B, 0x02BF},
+ {0x024E, 0x02BF}, {0x0251, 0x02BF}, {0x0254, 0x0A3F}, {0x0256, 0x0A3F},
+ {0x0258, 0x0A3F}, {0x025A, 0x0A3F}, {0x025C, 0x0A3F}, {0x025E, 0x0A3F},
+ {0x0263, 0x007C}, {0x0100, 0x0004}, {0xBE5B, 0x3500}, {0x800E, 0x200F},
+ {0xBE1D, 0x0F00}, {0x8001, 0x5011}, {0x800A, 0xA2F4}, {0x800B, 0x17A3},
+ {0xBE4B, 0x17A3}, {0xBE41, 0x5011}, {0xBE17, 0x2100}, {0x8000, 0x8304},
+ {0xBE40, 0x8304}, {0xBE4A, 0xA2F4}, {0x800C, 0xA8D5}, {0x8014, 0x5500},
+ {0x8015, 0x0004}, {0xBE4C, 0xA8D5}, {0xBE59, 0x0008}, {0xBE09, 0x0E00},
+ {0xBE36, 0x1036}, {0xBE37, 0x1036}, {0x800D, 0x00FF}, {0xBE4D, 0x00FF},
+};
+
+/* DGN3500, "netgear,dgn3500", "netgear,dgn3500b" */
+static const struct rtl8366rb_jam_tbl_entry rtl8366rb_init_jam_dgn3500[] = {
+ {0x0000, 0x0830}, {0x0400, 0x8130}, {0x000A, 0x83ED}, {0x0F51, 0x0017},
+ {0x02F5, 0x0048}, {0x02FA, 0xFFDF}, {0x02FB, 0xFFE0}, {0x0450, 0x0000},
+ {0x0401, 0x0000}, {0x0431, 0x0960},
+};
+
+/* This jam table activates "green ethernet", which means low power mode
+ * and is claimed to detect the cable length and not use more power than
+ * necessary, and the ports should enter power saving mode 10 seconds after
+ * a cable is disconnected. Seems to always be the same.
+ */
+static const struct rtl8366rb_jam_tbl_entry rtl8366rb_green_jam[] = {
+ {0xBE78, 0x323C}, {0xBE77, 0x5000}, {0xBE2E, 0x7BA7},
+ {0xBE59, 0x3459}, {0xBE5A, 0x745A}, {0xBE5B, 0x785C},
+ {0xBE5C, 0x785C}, {0xBE6E, 0xE120}, {0xBE79, 0x323C},
+};
+
+/* Function that jams the tables in the proper registers */
+static int rtl8366rb_jam_table(const struct rtl8366rb_jam_tbl_entry *jam_table,
+ int jam_size, struct realtek_priv *priv,
+ bool write_dbg)
+{
+ u32 val;
+ int ret;
+ int i;
+
+ for (i = 0; i < jam_size; i++) {
+ if ((jam_table[i].reg & 0xBE00) == 0xBE00) {
+ ret = regmap_read(priv->map,
+ RTL8366RB_PHY_ACCESS_BUSY_REG,
+ &val);
+ if (ret)
+ return ret;
+ if (!(val & RTL8366RB_PHY_INT_BUSY)) {
+ ret = regmap_write(priv->map,
+ RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_WRITE);
+ if (ret)
+ return ret;
+ }
+ }
+ if (write_dbg)
+ dev_dbg(priv->dev, "jam %04x into register %04x\n",
+ jam_table[i].val,
+ jam_table[i].reg);
+ ret = regmap_write(priv->map,
+ jam_table[i].reg,
+ jam_table[i].val);
+ if (ret)
+ return ret;
+ }
+ return 0;
+}
+
+static int rtl8366rb_setup(struct realtek_priv *priv)
+{
+ const struct rtl8366rb_jam_tbl_entry *jam_table;
+ u32 chip_ver = 0;
+ u32 chip_id = 0;
+ int jam_size;
+ u32 val;
+ int ret;
+ int i;
+
+ ret = regmap_read(priv->map, RTL8366RB_CHIP_ID_REG, &chip_id);
+ if (ret) {
+ dev_err(priv->dev, "unable to read chip id\n");
+ return ret;
+ }
+
+ switch (chip_id) {
+ case RTL8366RB_CHIP_ID_8366:
+ break;
+ default:
+ dev_err(priv->dev, "unknown chip id (%04x)\n", chip_id);
+ return -ENODEV;
+ }
+
+ ret = regmap_read(priv->map, RTL8366RB_CHIP_VERSION_CTRL_REG,
+ &chip_ver);
+ if (ret) {
+ dev_err(priv->dev, "unable to read chip version\n");
+ return ret;
+ }
+
+ dev_info(priv->dev, "RTL%04x ver %u chip found\n",
+ chip_id, chip_ver & RTL8366RB_CHIP_VERSION_MASK);
+
+ /* Do the init dance using the right jam table */
+ switch (chip_ver) {
+ case 0:
+ jam_table = rtl8366rb_init_jam_ver_0;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_ver_0);
+ break;
+ case 1:
+ jam_table = rtl8366rb_init_jam_ver_1;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_ver_1);
+ break;
+ case 2:
+ jam_table = rtl8366rb_init_jam_ver_2;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_ver_2);
+ break;
+ default:
+ jam_table = rtl8366rb_init_jam_ver_3;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_ver_3);
+ break;
+ }
+
+ /* Special jam tables for special routers
+ * TODO: are these necessary? Maintainers, please test
+ * without them, using just the off-the-shelf tables.
+ */
+ if (of_machine_is_compatible("belkin,f5d8235-v1")) {
+ jam_table = rtl8366rb_init_jam_f5d8235;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_f5d8235);
+ }
+ if (of_machine_is_compatible("netgear,dgn3500") ||
+ of_machine_is_compatible("netgear,dgn3500b")) {
+ jam_table = rtl8366rb_init_jam_dgn3500;
+ jam_size = ARRAY_SIZE(rtl8366rb_init_jam_dgn3500);
+ }
+
+ ret = rtl8366rb_jam_table(jam_table, jam_size, priv, true);
+ if (ret)
+ return ret;
+
+ /* Isolate all user ports so they can only send packets to itself and the CPU port */
+ for (i = 0; i < RTL8366RB_PORT_NUM_CPU; i++) {
+ ret = regmap_write(priv->map, RTL8366RB_PORT_ISO(i),
+ RTL8366RB_PORT_ISO_PORTS(BIT(RTL8366RB_PORT_NUM_CPU)) |
+ RTL8366RB_PORT_ISO_EN);
+ if (ret)
+ return ret;
+ }
+ /* CPU port can send packets to all ports */
+ ret = regmap_write(priv->map, RTL8366RB_PORT_ISO(RTL8366RB_PORT_NUM_CPU),
+ RTL8366RB_PORT_ISO_PORTS(dsa_user_ports(priv->ds)) |
+ RTL8366RB_PORT_ISO_EN);
+ if (ret)
+ return ret;
+
+ /* Set up the "green ethernet" feature */
+ ret = rtl8366rb_jam_table(rtl8366rb_green_jam,
+ ARRAY_SIZE(rtl8366rb_green_jam), priv, false);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(priv->map,
+ RTL8366RB_GREEN_FEATURE_REG,
+ (chip_ver == 1) ? 0x0007 : 0x0003);
+ if (ret)
+ return ret;
+
+ /* Vendor driver sets 0x240 in registers 0xc and 0xd (undocumented) */
+ ret = regmap_write(priv->map, 0x0c, 0x240);
+ if (ret)
+ return ret;
+ ret = regmap_write(priv->map, 0x0d, 0x240);
+ if (ret)
+ return ret;
+
+ /* Set some random MAC address */
+ ret = rtl8366rb_set_addr(priv);
+ if (ret)
+ return ret;
+
+ /* Enable CPU port with custom DSA tag 8899.
+ *
+ * If you set RTL8368RB_CPU_NO_TAG (bit 15) in this registers
+ * the custom tag is turned off.
+ */
+ ret = regmap_update_bits(priv->map, RTL8368RB_CPU_CTRL_REG,
+ 0xFFFF,
+ BIT(priv->cpu_port));
+ if (ret)
+ return ret;
+
+ /* Make sure we default-enable the fixed CPU port */
+ ret = regmap_update_bits(priv->map, RTL8366RB_PECR,
+ BIT(priv->cpu_port),
+ 0);
+ if (ret)
+ return ret;
+
+ /* Set maximum packet length to 1536 bytes */
+ ret = regmap_update_bits(priv->map, RTL8366RB_SGCR,
+ RTL8366RB_SGCR_MAX_LENGTH_MASK,
+ RTL8366RB_SGCR_MAX_LENGTH_1536);
+ if (ret)
+ return ret;
+
+ /* Disable learning for all ports */
+ ret = regmap_write(priv->map, RTL8366RB_PORT_LEARNDIS_CTRL,
+ RTL8366RB_PORT_ALL);
+ if (ret)
+ return ret;
+
+ /* Enable auto ageing for all ports */
+ ret = regmap_write(priv->map, RTL8366RB_SECURITY_CTRL, 0);
+ if (ret)
+ return ret;
+
+ /* Port 4 setup: this enables Port 4, usually the WAN port,
+ * common PHY IO mode is apparently mode 0, and this is not what
+ * the port is initialized to. There is no explanation of the
+ * IO modes in the Realtek source code, if your WAN port is
+ * connected to something exotic such as fiber, then this might
+ * be worth experimenting with.
+ */
+ ret = regmap_update_bits(priv->map, RTL8366RB_PMC0,
+ RTL8366RB_PMC0_P4_IOMODE_MASK,
+ 0 << RTL8366RB_PMC0_P4_IOMODE_SHIFT);
+ if (ret)
+ return ret;
+
+ /* Accept all packets by default, we enable filtering on-demand */
+ ret = regmap_write(priv->map, RTL8366RB_VLAN_INGRESS_CTRL1_REG,
+ 0);
+ if (ret)
+ return ret;
+ ret = regmap_write(priv->map, RTL8366RB_VLAN_INGRESS_CTRL2_REG,
+ 0);
+ if (ret)
+ return ret;
+
+ /* Don't drop packets whose DA has not been learned */
+ ret = regmap_update_bits(priv->map, RTL8366RB_SSCR2,
+ RTL8366RB_SSCR2_DROP_UNKNOWN_DA, 0);
+ if (ret)
+ return ret;
+
+ /* Set blinking, TODO: make this configurable */
+ ret = regmap_update_bits(priv->map, RTL8366RB_LED_BLINKRATE_REG,
+ RTL8366RB_LED_BLINKRATE_MASK,
+ RTL8366RB_LED_BLINKRATE_56MS);
+ if (ret)
+ return ret;
+
+ /* Set up LED activity:
+ * Each port has 4 LEDs, we configure all ports to the same
+ * behaviour (no individual config) but we can set up each
+ * LED separately.
+ */
+ if (priv->leds_disabled) {
+ /* Turn everything off */
+ regmap_update_bits(priv->map,
+ RTL8366RB_LED_0_1_CTRL_REG,
+ 0x0FFF, 0);
+ regmap_update_bits(priv->map,
+ RTL8366RB_LED_2_3_CTRL_REG,
+ 0x0FFF, 0);
+ regmap_update_bits(priv->map,
+ RTL8366RB_INTERRUPT_CONTROL_REG,
+ RTL8366RB_P4_RGMII_LED,
+ 0);
+ val = RTL8366RB_LED_OFF;
+ } else {
+ /* TODO: make this configurable per LED */
+ val = RTL8366RB_LED_FORCE;
+ }
+ for (i = 0; i < 4; i++) {
+ ret = regmap_update_bits(priv->map,
+ RTL8366RB_LED_CTRL_REG,
+ 0xf << (i * 4),
+ val << (i * 4));
+ if (ret)
+ return ret;
+ }
+
+ // TODO: Untested: We'll assume POR defaults to suffice for our usecase
+ // rtl8366_reset_vlan(priv);
+
+ rtl8366rb_irq_setup(priv);
+
+ if (priv->setup_interface) {
+ ret = priv->setup_interface(priv->ds);
+ if (ret) {
+ dev_err(priv->dev, "could not set up MDIO bus\n");
+ return -ENODEV;
+ }
+ }
+
+ return 0;
+}
+
+static enum dsa_tag_protocol rtl8366_get_tag_protocol(struct realtek_priv *priv)
+{
+ /* This switch uses the 4 byte protocol A Realtek DSA tag */
+ return DSA_TAG_PROTO_RTL4_A;
+}
+
+static void
+rtl8366rb_mac_link_up(struct dsa_switch *ds, int port)
+{
+ struct realtek_priv *priv = ds->priv;
+ int ret;
+
+ if (port != priv->cpu_port)
+ return;
+
+ dev_dbg(priv->dev, "MAC link up on CPU port (%d)\n", port);
+
+ /* Force the fixed CPU port into 1Gbit mode, no autonegotiation */
+ ret = regmap_update_bits(priv->map, RTL8366RB_MAC_FORCE_CTRL_REG,
+ BIT(port), BIT(port));
+ if (ret) {
+ dev_err(priv->dev, "failed to force 1Gbit on CPU port\n");
+ return;
+ }
+
+ ret = regmap_update_bits(priv->map, RTL8366RB_PAACR2,
+ 0xFF00U,
+ RTL8366RB_PAACR_CPU_PORT << 8);
+ if (ret) {
+ dev_err(priv->dev, "failed to set PAACR on CPU port\n");
+ return;
+ }
+
+ /* Enable the CPU port */
+ ret = regmap_update_bits(priv->map, RTL8366RB_PECR, BIT(port),
+ 0);
+ if (ret) {
+ dev_err(priv->dev, "failed to enable the CPU port\n");
+ return;
+ }
+}
+
+static void
+rtl8366rb_mac_link_down(struct dsa_switch *ds, int port)
+{
+ struct realtek_priv *priv = ds->priv;
+ int ret;
+
+ if (port != priv->cpu_port)
+ return;
+
+ dev_dbg(priv->dev, "MAC link down on CPU port (%d)\n", port);
+
+ /* Disable the CPU port */
+ ret = regmap_update_bits(priv->map, RTL8366RB_PECR, BIT(port),
+ BIT(port));
+ if (ret) {
+ dev_err(priv->dev, "failed to disable the CPU port\n");
+ return;
+ }
+}
+
+static void rb8366rb_set_port_led(struct realtek_priv *priv,
+ int port, bool enable)
+{
+ u16 val = enable ? 0x3f : 0;
+ int ret;
+
+ if (priv->leds_disabled)
+ return;
+
+ switch (port) {
+ case 0:
+ ret = regmap_update_bits(priv->map,
+ RTL8366RB_LED_0_1_CTRL_REG,
+ 0x3F, val);
+ break;
+ case 1:
+ ret = regmap_update_bits(priv->map,
+ RTL8366RB_LED_0_1_CTRL_REG,
+ 0x3F << RTL8366RB_LED_1_OFFSET,
+ val << RTL8366RB_LED_1_OFFSET);
+ break;
+ case 2:
+ ret = regmap_update_bits(priv->map,
+ RTL8366RB_LED_2_3_CTRL_REG,
+ 0x3F, val);
+ break;
+ case 3:
+ ret = regmap_update_bits(priv->map,
+ RTL8366RB_LED_2_3_CTRL_REG,
+ 0x3F << RTL8366RB_LED_3_OFFSET,
+ val << RTL8366RB_LED_3_OFFSET);
+ break;
+ case 4:
+ ret = regmap_update_bits(priv->map,
+ RTL8366RB_INTERRUPT_CONTROL_REG,
+ RTL8366RB_P4_RGMII_LED,
+ enable ? RTL8366RB_P4_RGMII_LED : 0);
+ break;
+ default:
+ dev_err(priv->dev, "no LED for port %d\n", port);
+ return;
+ }
+ if (ret)
+ dev_err(priv->dev, "error updating LED on port %d\n", port);
+}
+
+static void
+rtl8366rb_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
+{
+ struct realtek_priv *priv = ds->priv;
+ u32 val;
+ int i;
+
+ switch (state) {
+ case BR_STATE_DISABLED:
+ val = RTL8366RB_STP_STATE_DISABLED;
+ break;
+ case BR_STATE_FORWARDING:
+ val = RTL8366RB_STP_STATE_FORWARDING;
+ break;
+ default:
+ dev_err(priv->dev, "unknown bridge state requested\n");
+ return;
+ }
+
+ /* Set the same status for the port on all the FIDs */
+ for (i = 0; i < RTL8366RB_NUM_FIDS; i++) {
+ regmap_update_bits(priv->map, RTL8366RB_STP_STATE_BASE + i,
+ RTL8366RB_STP_STATE_MASK(port),
+ RTL8366RB_STP_STATE(port, val));
+ }
+}
+
+static int
+rtl8366rb_port_enable(struct dsa_port *dp, int port,
+ struct phy_device *phy)
+{
+ struct realtek_priv *priv = dp->ds->priv;
+ int ret;
+
+ rtl8366rb_mac_link_up(dp->ds, port);
+
+ dev_dbg(priv->dev, "enable port %d\n", port);
+ ret = regmap_update_bits(priv->map, RTL8366RB_PECR, BIT(port),
+ 0);
+ if (ret)
+ return ret;
+
+ rb8366rb_set_port_led(priv, port, true);
+
+ rtl8366rb_port_stp_state_set(dp->ds, port, BR_STATE_FORWARDING);
+
+ return 0;
+}
+
+static void
+rtl8366rb_port_disable(struct dsa_port *dp, int port,
+ struct phy_device *phy)
+{
+ struct realtek_priv *priv = dp->ds->priv;
+ int ret;
+
+ rtl8366rb_port_stp_state_set(dp->ds, port, BR_STATE_DISABLED);
+
+ dev_dbg(priv->dev, "disable port %d\n", port);
+ ret = regmap_update_bits(priv->map, RTL8366RB_PECR, BIT(port),
+ BIT(port));
+ if (ret)
+ return;
+
+ rb8366rb_set_port_led(priv, port, false);
+
+ rtl8366rb_mac_link_down(dp->ds, port);
+}
+
+static int rtl8366rb_phy_read(struct realtek_priv *priv, int phy, int regnum)
+{
+ u32 val;
+ u32 reg;
+ int ret;
+
+ if (phy > RTL8366RB_PHY_NO_MAX)
+ return -EINVAL;
+
+ ret = regmap_write(priv->map_nolock, RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_READ);
+ if (ret)
+ goto out;
+
+ reg = 0x8000 | (1 << (phy + RTL8366RB_PHY_NO_OFFSET)) | regnum;
+
+ ret = regmap_write(priv->map_nolock, reg, 0);
+ if (ret) {
+ dev_err(priv->dev,
+ "failed to write PHY%d reg %04x @ %04x, ret %d\n",
+ phy, regnum, reg, ret);
+ goto out;
+ }
+
+ ret = regmap_read(priv->map_nolock, RTL8366RB_PHY_ACCESS_DATA_REG,
+ &val);
+ if (ret)
+ goto out;
+
+ ret = val;
+
+ dev_dbg(priv->dev, "read PHY%d register 0x%04x @ %08x, val <- %04x\n",
+ phy, regnum, reg, val);
+
+out:
+ return ret;
+}
+
+static int rtl8366rb_phy_write(struct realtek_priv *priv, int phy, int regnum,
+ u16 val)
+{
+ u32 reg;
+ int ret;
+
+ if (phy > RTL8366RB_PHY_NO_MAX)
+ return -EINVAL;
+
+ ret = regmap_write(priv->map_nolock, RTL8366RB_PHY_ACCESS_CTRL_REG,
+ RTL8366RB_PHY_CTRL_WRITE);
+ if (ret)
+ goto out;
+
+ reg = 0x8000 | (1 << (phy + RTL8366RB_PHY_NO_OFFSET)) | regnum;
+
+ dev_dbg(priv->dev, "write PHY%d register 0x%04x @ %04x, val -> %04x\n",
+ phy, regnum, reg, val);
+
+ ret = regmap_write(priv->map_nolock, reg, val);
+ if (ret)
+ goto out;
+
+out:
+ return ret;
+}
+
+static int rtl8366rb_dsa_phy_read(struct dsa_switch *ds, int phy, int regnum)
+{
+ return rtl8366rb_phy_read(ds->priv, phy, regnum);
+}
+
+static int rtl8366rb_dsa_phy_write(struct dsa_switch *ds, int phy, int regnum,
+ u16 val)
+{
+ return rtl8366rb_phy_write(ds->priv, phy, regnum, val);
+}
+
+static int rtl8366rb_reset_chip(struct realtek_priv *priv)
+{
+ int timeout = 10;
+ u32 val;
+ int ret;
+
+ priv->write_reg_noack(priv, RTL8366RB_RESET_CTRL_REG,
+ RTL8366RB_CHIP_CTRL_RESET_HW);
+ do {
+ udelay(20000);
+ ret = regmap_read(priv->map, RTL8366RB_RESET_CTRL_REG, &val);
+ if (ret)
+ return ret;
+
+ if (!(val & RTL8366RB_CHIP_CTRL_RESET_HW))
+ break;
+ } while (--timeout);
+
+ if (!timeout) {
+ dev_err(priv->dev, "timeout waiting for the switch to reset\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int rtl8366rb_detect(struct realtek_priv *priv)
+{
+ struct device *dev = priv->dev;
+ int ret;
+ u32 val;
+
+ /* Detect device */
+ ret = regmap_read(priv->map, 0x5c, &val);
+ if (ret) {
+ dev_err(dev, "can't get chip ID (%d)\n", ret);
+ return ret;
+ }
+
+ switch (val) {
+ case 0x6027:
+ dev_info(dev, "found an RTL8366S switch\n");
+ dev_err(dev, "this switch is not yet supported, submit patches!\n");
+ return -ENODEV;
+ case 0x5937:
+ dev_info(dev, "found an RTL8366RB switch\n");
+ priv->cpu_port = RTL8366RB_PORT_NUM_CPU;
+ priv->num_ports = RTL8366RB_NUM_PORTS;
+ break;
+ default:
+ dev_info(dev, "found an Unknown Realtek switch (id=0x%04x)\n",
+ val);
+ break;
+ }
+
+ return rtl8366rb_reset_chip(priv);
+}
+
+static const struct dsa_switch_ops rtl8366rb_switch_ops_smi = {
+ .port_enable = rtl8366rb_port_enable,
+ .port_disable = rtl8366rb_port_disable,
+};
+
+static const struct dsa_switch_ops rtl8366rb_switch_ops_mdio = {
+ .phy_read = rtl8366rb_dsa_phy_read,
+ .phy_write = rtl8366rb_dsa_phy_write,
+ .port_enable = rtl8366rb_port_enable,
+ .port_disable = rtl8366rb_port_disable,
+};
+
+static const struct realtek_ops rtl8366rb_ops = {
+ .detect = rtl8366rb_detect,
+ .phy_read = rtl8366rb_phy_read,
+ .phy_write = rtl8366rb_phy_write,
+ .setup = rtl8366rb_setup,
+ .get_tag_protocol = rtl8366_get_tag_protocol,
+};
+
+const struct realtek_variant rtl8366rb_variant = {
+ .ds_ops_smi = &rtl8366rb_switch_ops_smi,
+ .ds_ops_mdio = &rtl8366rb_switch_ops_mdio,
+ .ops = &rtl8366rb_ops,
+ .clk_delay = 10,
+ .cmd_read = 0xa9,
+ .cmd_write = 0xa8,
+};
+EXPORT_SYMBOL_GPL(rtl8366rb_variant);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
+MODULE_DESCRIPTION("Driver for RTL8366RB ethernet switch");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/realtek-dsa/tag_rtl4_a.c b/drivers/net/realtek-dsa/tag_rtl4_a.c
new file mode 100644
index 000000000000..dabd4ccba2d9
--- /dev/null
+++ b/drivers/net/realtek-dsa/tag_rtl4_a.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Handler for Realtek 4 byte DSA switch tags
+ * Currently only supports protocol "A" found in RTL8366RB
+ * Copyright (c) 2020 Linus Walleij <linus.walleij@linaro.org>
+ *
+ * This "proprietary tag" header looks like so:
+ *
+ * -------------------------------------------------
+ * | MAC DA | MAC SA | 0x8899 | 2 bytes tag | Type |
+ * -------------------------------------------------
+ *
+ * The 2 bytes tag form a 16 bit big endian word. The exact
+ * meaning has been guessed from packet dumps from ingress
+ * frames.
+ */
+
+#include <net.h>
+
+#include "realtek.h"
+#include "dsa_priv.h"
+
+#define RTL4_A_HDR_LEN 4
+#define RTL4_A_ETHERTYPE 0x8899
+#define RTL4_A_PROTOCOL_SHIFT 12
+/*
+ * 0x1 = Realtek Remote Control protocol (RRCP)
+ * 0x2/0x3 seems to be used for loopback testing
+ * 0x9 = RTL8306 DSA protocol
+ * 0xa = RTL8366RB DSA protocol
+ */
+#define RTL4_A_PROTOCOL_RTL8366RB 0xa
+
+static int rtl4a_tag_xmit(struct dsa_port *dp, int port, void *packet, int length)
+{
+ struct device *dev = dp->ds->dev;
+ __be16 *p;
+ u8 *tag;
+ u16 out;
+
+ /* DSA core already pads out to at least 60 bytes */
+
+ dev_dbg(dev, "add realtek tag to package to port %d\n", port);
+
+ dsa_alloc_etype_header(packet, RTL4_A_HDR_LEN);
+ tag = dsa_etype_header_pos(packet);
+
+ /* Set Ethertype */
+ p = (__be16 *)tag;
+ *p = htons(RTL4_A_ETHERTYPE);
+
+ out = (RTL4_A_PROTOCOL_RTL8366RB << RTL4_A_PROTOCOL_SHIFT);
+ /* The lower bits indicate the port number */
+ out |= BIT(port);
+
+ p = (__be16 *)(tag + 2);
+ *p = htons(out);
+
+ return 0;
+}
+
+static int rtl4a_tag_rcv(struct dsa_switch *ds, int *port, void *packet, int length)
+{
+ struct device *dev = ds->dev;
+ u16 protport;
+ __be16 *p;
+ u16 etype;
+ u8 *tag;
+ u8 prot;
+
+ tag = packet + 2 * ETH_ALEN;
+ p = (__be16 *)tag;
+ etype = ntohs(*p);
+ if (etype != RTL4_A_ETHERTYPE) {
+ /* Not custom, just pass through */
+ dev_dbg(dev, "non-realtek ethertype 0x%04x\n", etype);
+ return -EINVAL;
+ }
+ p = (__be16 *)(tag + 2);
+ protport = ntohs(*p);
+ /* The 4 upper bits are the protocol */
+ prot = (protport >> RTL4_A_PROTOCOL_SHIFT) & 0x0f;
+ if (prot != RTL4_A_PROTOCOL_RTL8366RB) {
+ dev_err(dev, "unknown realtek protocol 0x%01x\n", prot);
+ return -EPROTO;
+ }
+ *port = protport & 0xff;
+
+ dsa_strip_etype_header(packet, RTL4_A_HDR_LEN);
+
+ return 0;
+}
+
+const struct dsa_device_ops rtl4a_netdev_ops = {
+ .name = "rtl4a",
+ .proto = DSA_TAG_PROTO_RTL4_A,
+ .xmit = rtl4a_tag_xmit,
+ .rcv = rtl4a_tag_rcv,
+ .needed_headroom = RTL4_A_HDR_LEN,
+};
+
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_RTL4_A);
diff --git a/drivers/net/realtek-dsa/tag_rtl8_4.c b/drivers/net/realtek-dsa/tag_rtl8_4.c
new file mode 100644
index 000000000000..a6762fc4e90d
--- /dev/null
+++ b/drivers/net/realtek-dsa/tag_rtl8_4.c
@@ -0,0 +1,205 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Handler for Realtek 8 byte switch tags
+ *
+ * Copyright (C) 2021 Alvin Šipraga <alsi@bang-olufsen.dk>
+ *
+ * NOTE: Currently only supports protocol "4" found in the RTL8365MB, hence
+ * named tag_rtl8_4.
+ *
+ * This tag has the following format:
+ *
+ * 0 7|8 15
+ * |-----------------------------------+-----------------------------------|---
+ * | (16-bit) | ^
+ * | Realtek EtherType [0x8899] | |
+ * |-----------------------------------+-----------------------------------| 8
+ * | (8-bit) | (8-bit) |
+ * | Protocol [0x04] | REASON | b
+ * |-----------------------------------+-----------------------------------| y
+ * | (1) | (1) | (2) | (1) | (3) | (1) | (1) | (1) | (5) | t
+ * | FID_EN | X | FID | PRI_EN | PRI | KEEP | X | LEARN_DIS | X | e
+ * |-----------------------------------+-----------------------------------| s
+ * | (1) | (15-bit) | |
+ * | ALLOW | TX/RX | v
+ * |-----------------------------------+-----------------------------------|---
+ *
+ * With the following field descriptions:
+ *
+ * field | description
+ * ------------+-------------
+ * Realtek | 0x8899: indicates that this is a proprietary Realtek tag;
+ * EtherType | note that Realtek uses the same EtherType for
+ * | other incompatible tag formats (e.g. tag_rtl4_a.c)
+ * Protocol | 0x04: indicates that this tag conforms to this format
+ * X | reserved
+ * ------------+-------------
+ * REASON | reason for forwarding packet to CPU
+ * | 0: packet was forwarded or flooded to CPU
+ * | 80: packet was trapped to CPU
+ * FID_EN | 1: packet has an FID
+ * | 0: no FID
+ * FID | FID of packet (if FID_EN=1)
+ * PRI_EN | 1: force priority of packet
+ * | 0: don't force priority
+ * PRI | priority of packet (if PRI_EN=1)
+ * KEEP | preserve packet VLAN tag format
+ * LEARN_DIS | don't learn the source MAC address of the packet
+ * ALLOW | 1: treat TX/RX field as an allowance port mask, meaning the
+ * | packet may only be forwarded to ports specified in the
+ * | mask
+ * | 0: no allowance port mask, TX/RX field is the forwarding
+ * | port mask
+ * TX/RX | TX (switch->CPU): port number the packet was received on
+ * | RX (CPU->switch): forwarding port mask (if ALLOW=0)
+ * | allowance port mask (if ALLOW=1)
+ *
+ * The tag can be positioned before Ethertype, using tag "rtl8_4":
+ *
+ * +--------+--------+------------+------+-----
+ * | MAC DA | MAC SA | 8 byte tag | Type | ...
+ * +--------+--------+------------+------+-----
+ *
+ * The tag can also appear between the end of the payload and before the CRC,
+ * using tag "rtl8_4t":
+ *
+ * +--------+--------+------+-----+---------+------------+-----+
+ * | MAC DA | MAC SA | TYPE | ... | payload | 8-byte tag | CRC |
+ * +--------+--------+------+-----+---------+------------+-----+
+ *
+ * The added bytes after the payload will break most checksums, either in
+ * software or hardware. We don't care for checksums in barebox, so this
+ * is just ignored.
+ *
+ */
+
+#include <linux/bitfield.h>
+#include <net.h>
+
+#include "realtek.h"
+#include "dsa_priv.h"
+
+/* Protocols supported:
+ *
+ * 0x04 = RTL8365MB DSA protocol
+ */
+
+#define ETH_P_REALTEK 0x8899
+
+#define RTL8_4_TAG_LEN 8
+
+#define RTL8_4_PROTOCOL GENMASK(15, 8)
+#define RTL8_4_PROTOCOL_RTL8365MB 0x04
+#define RTL8_4_REASON GENMASK(7, 0)
+#define RTL8_4_REASON_FORWARD 0
+#define RTL8_4_REASON_TRAP 80
+
+#define RTL8_4_LEARN_DIS BIT(5)
+
+#define RTL8_4_TX GENMASK(3, 0)
+#define RTL8_4_RX GENMASK(10, 0)
+
+static void rtl8_4_write_tag(int port, void *tag)
+{
+ __be16 tag16[RTL8_4_TAG_LEN / 2];
+
+ /* Set Realtek EtherType */
+ tag16[0] = htons(ETH_P_REALTEK);
+
+ /* Set Protocol; zero REASON */
+ tag16[1] = htons(FIELD_PREP(RTL8_4_PROTOCOL, RTL8_4_PROTOCOL_RTL8365MB));
+
+ /* Zero FID_EN, FID, PRI_EN, PRI, KEEP; set LEARN_DIS */
+ tag16[2] = htons(FIELD_PREP(RTL8_4_LEARN_DIS, 1));
+
+ /* Zero ALLOW; set RX (CPU->switch) forwarding port mask */
+ tag16[3] = htons(FIELD_PREP(RTL8_4_RX, BIT(port)));
+
+ memcpy(tag, tag16, RTL8_4_TAG_LEN);
+}
+
+static int rtl8_4_tag_xmit(struct dsa_port *dp, int port, void *packet, int length)
+{
+ dsa_alloc_etype_header(packet, RTL8_4_TAG_LEN);
+
+ rtl8_4_write_tag(port, dsa_etype_header_pos(packet));
+
+ return 0;
+}
+
+static int rtl8_4t_tag_xmit(struct dsa_port *dp, int port, void *packet, int length)
+{
+ rtl8_4_write_tag(port, packet + length - dp->ds->needed_tx_tailroom);
+
+ return 0;
+}
+
+static int rtl8_4_read_tag(int *port, struct device *dev, void *tag)
+{
+ __be16 tag16[RTL8_4_TAG_LEN / 2];
+ u16 etype;
+ u8 proto;
+
+ memcpy(tag16, tag, RTL8_4_TAG_LEN);
+
+ /* Parse Realtek EtherType */
+ etype = ntohs(tag16[0]);
+ if (unlikely(etype != ETH_P_REALTEK)) {
+ dev_warn(dev, "non-realtek ethertype 0x%04x\n", etype);
+ return -EPROTO;
+ }
+
+ /* Parse Protocol */
+ proto = FIELD_GET(RTL8_4_PROTOCOL, ntohs(tag16[1]));
+ if (unlikely(proto != RTL8_4_PROTOCOL_RTL8365MB)) {
+ dev_warn(dev, "unknown realtek protocol 0x%02x\n", proto);
+ return -EPROTO;
+ }
+
+ /* Parse TX (switch->CPU) */
+ *port = FIELD_GET(RTL8_4_TX, ntohs(tag16[3]));
+
+ return 0;
+}
+
+static int rtl8_4_tag_rcv(struct dsa_switch *ds, int *port, void *packet, int length)
+{
+ int ret;
+
+ ret = rtl8_4_read_tag(port, ds->dev, dsa_etype_header_pos(packet));
+ if (unlikely(ret))
+ return ret;
+
+ dsa_strip_etype_header(packet, RTL8_4_TAG_LEN);
+
+ return 0;
+}
+
+static int rtl8_4t_tag_rcv(struct dsa_switch *ds, int *port, void *packet, int length)
+{
+ return rtl8_4_read_tag(port, ds->dev, packet + length - ds->needed_rx_tailroom);
+}
+
+/* Ethertype version */
+const struct dsa_device_ops rtl8_4_netdev_ops = {
+ .name = "rtl8_4",
+ .proto = DSA_TAG_PROTO_RTL8_4,
+ .xmit = rtl8_4_tag_xmit,
+ .rcv = rtl8_4_tag_rcv,
+ .needed_headroom = RTL8_4_TAG_LEN,
+};
+
+MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_RTL8_4);
+
+/* Tail version */
+const struct dsa_device_ops rtl8_4t_netdev_ops = {
+ .name = "rtl8_4t",
+ .proto = DSA_TAG_PROTO_RTL8_4T,
+ .xmit = rtl8_4t_tag_xmit,
+ .rcv = rtl8_4t_tag_rcv,
+ .needed_tailroom = RTL8_4_TAG_LEN,
+};
+
+MODULE_ALIAS_DSA_TAG_DRIVER(DSA_TAG_PROTO_RTL8_4T);
+
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/realtek-dsa/tagger.c b/drivers/net/realtek-dsa/tagger.c
new file mode 100644
index 000000000000..1d4461aebcb8
--- /dev/null
+++ b/drivers/net/realtek-dsa/tagger.c
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "realtek.h"
+
+int realtek_dsa_init_tagger(struct realtek_priv *priv)
+{
+ const struct dsa_device_ops *tagger_ops;
+ struct dsa_switch_ops *ops;
+
+ /* TODO: Tagging can be configured per port in Linux. barebox DSA core
+ * will need some refactoring to do that. For now we just use the
+ * Linux default and leave ->change_tag_protocol unused and
+ * dsa-tag-protocol OF properties unheeded.
+ */
+ switch (priv->ops->get_tag_protocol(priv)) {
+ case DSA_TAG_PROTO_RTL4_A:
+ tagger_ops = &rtl4a_netdev_ops;
+ break;
+ case DSA_TAG_PROTO_RTL8_4:
+ tagger_ops = &rtl8_4_netdev_ops;
+ break;
+ case DSA_TAG_PROTO_RTL8_4T:
+ tagger_ops = &rtl8_4t_netdev_ops;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ops = memdup(priv->ds->ops, sizeof(*priv->ds->ops));
+ ops->xmit = tagger_ops->xmit;
+ ops->rcv = tagger_ops->rcv;
+ priv->ds->ops = ops;
+ priv->ds->needed_headroom = tagger_ops->needed_headroom;
+ priv->ds->needed_rx_tailroom = tagger_ops->needed_tailroom;
+ priv->ds->needed_tx_tailroom = tagger_ops->needed_tailroom;
+
+ return 0;
+}
diff --git a/include/linux/barebox-wrapper.h b/include/linux/barebox-wrapper.h
index 8f2473abe8aa..28e87cb17316 100644
--- a/include/linux/barebox-wrapper.h
+++ b/include/linux/barebox-wrapper.h
@@ -21,6 +21,7 @@ static inline void vfree(const void *addr)
#define MODULE_LICENSE(x)
#define MODULE_ALIAS(x)
#define MODULE_DEVICE_TABLE(bus, table)
+#define MODULE_ALIAS_DSA_TAG_DRIVER(drv)
#define __user
#define __init
diff --git a/include/linux/if_bridge.h b/include/linux/if_bridge.h
new file mode 100644
index 000000000000..05f8e3a957dd
--- /dev/null
+++ b/include/linux/if_bridge.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+
+#ifndef _LINUX_IF_BRIDGE_H
+#define _LINUX_IF_BRIDGE_H
+
+#define BR_STATE_DISABLED 0
+#define BR_STATE_FORWARDING 3
+
+#endif
diff --git a/include/net.h b/include/net.h
index 27dea3a12d6e..0555b0bd6bed 100644
--- a/include/net.h
+++ b/include/net.h
@@ -416,7 +416,8 @@ static inline int is_broadcast_ether_addr(const u8 *addr)
return (addr[0] & addr[1] & addr[2] & addr[3] & addr[4] & addr[5]) == 0xff;
}
-#define ETH_ALEN 6
+#define ETH_ALEN 6 /* Octets in an Ethernet address */
+#define ETH_HLEN 14 /* Total octets in header.*/
/**
* random_ether_addr - Generate software assigned random Ethernet address
--
2.30.2
next prev parent reply other threads:[~2023-01-16 13:49 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-16 13:44 [PATCH 0/9] " Ahmad Fatoum
2023-01-16 13:44 ` [PATCH 1/9] driver: alias of_match_ptr and DRV_OF_COMPAT Ahmad Fatoum
2023-01-16 13:44 ` [PATCH 2/9] gpiolib: implement gpio_direction_input/output Ahmad Fatoum
2023-01-16 13:44 ` [PATCH 3/9] net: dsa: rename dsa_ops to dsa_switch_ops Ahmad Fatoum
2023-01-16 13:44 ` [PATCH 4/9] net: dsa: factor out dsa_port_alloc helper Ahmad Fatoum
2023-01-16 13:44 ` [PATCH 5/9] net: dsa: populate struct dsa_port::index/dev members Ahmad Fatoum
2023-01-16 13:44 ` [PATCH 6/9] net: dsa: always call port_pre_enable before port_enable Ahmad Fatoum
2023-01-16 13:44 ` [PATCH 7/9] net: dsa: add some helpers to ease porting kernel drivers Ahmad Fatoum
2023-01-16 13:45 ` [PATCH 8/9] net: dsa: add struct dsa_switch::priv member for driver use Ahmad Fatoum
2023-01-16 13:45 ` Ahmad Fatoum [this message]
2023-01-23 8:21 ` [PATCH 0/9] net: dsa: add Realtek (rtl8365mb/rtl8366rb) switch support Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230116134501.2006391-10-a.fatoum@pengutronix.de \
--to=a.fatoum@pengutronix.de \
--cc=barebox@lists.infradead.org \
--cc=ore@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox