From: Sascha Hauer <s.hauer@pengutronix.de>
To: "open list:BAREBOX" <barebox@lists.infradead.org>
Subject: [PATCH 07/13] video: Add Sitronix st7789v panel driver
Date: Thu, 26 Sep 2024 15:15:05 +0200 [thread overview]
Message-ID: <20240926-vop2-v1-7-fe0581f2020b@pengutronix.de> (raw)
In-Reply-To: <20240926-vop2-v1-0-fe0581f2020b@pengutronix.de>
This adds a panel driver for the Sitronix st7789v panel based
on the corresponding Linux-6.10 driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
---
drivers/video/Kconfig | 8 +
drivers/video/Makefile | 1 +
drivers/video/panel-sitronix-st7789v.c | 652 +++++++++++++++++++++++++++++++++
include/video/vpl.h | 1 +
4 files changed, 662 insertions(+)
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 9e176d3198..e86f511da4 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -186,6 +186,14 @@ config DRIVER_VIDEO_PANEL_ILITEK_ILI9341
QVGA (240x320) RGB panels. support serial & parallel rgb
interface.
+config DRIVER_VIDEO_PANEL_SITRONIX_ST7789V
+ tristate "Sitronix ST7789V panel"
+ depends on OFTREE && SPI
+ select VIDEO_VPL
+ help
+ Say Y here if you want to enable support for the Sitronix
+ ST7789V controller for 240x320 LCD panels
+
config DRIVER_VIDEO_PANEL_MIPI_DBI
tristate "DRM support for MIPI DBI compatible panels"
depends on OFTREE && SPI
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 9e6a241a33..37a184a7e2 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_DRIVER_VIDEO_SIMPLE_PANEL) += simple-panel.o
obj-$(CONFIG_DRIVER_VIDEO_MIPI_DBI) += mipi_dbi.o
obj-$(CONFIG_DRIVER_VIDEO_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o
obj-$(CONFIG_DRIVER_VIDEO_PANEL_MIPI_DBI) += panel-mipi-dbi.o
+obj-$(CONFIG_DRIVER_VIDEO_PANEL_SITRONIX_ST7789V) += panel-sitronix-st7789v.o
obj-$(CONFIG_DRIVER_VIDEO_ATMEL) += atmel_lcdfb.o atmel_lcdfb_core.o
obj-$(CONFIG_DRIVER_VIDEO_ATMEL_HLCD) += atmel_hlcdfb.o atmel_lcdfb_core.o
diff --git a/drivers/video/panel-sitronix-st7789v.c b/drivers/video/panel-sitronix-st7789v.c
new file mode 100644
index 0000000000..36852fb88e
--- /dev/null
+++ b/drivers/video/panel-sitronix-st7789v.c
@@ -0,0 +1,652 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2017 Free Electrons
+ */
+
+#include <driver.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <regulator.h>
+#include <spi/spi.h>
+#include <fb.h>
+#include <linux/device.h>
+#include <video/vpl.h>
+#include <video/videomode.h>
+#include <video/drm/drm_connector.h>
+#include <video/mipi_display.h>
+#include <video/media-bus-format.h>
+
+#define ST7789V_RAMCTRL_CMD 0xb0
+#define ST7789V_RAMCTRL_RM_RGB BIT(4)
+#define ST7789V_RAMCTRL_DM_RGB BIT(0)
+#define ST7789V_RAMCTRL_MAGIC (3 << 6)
+#define ST7789V_RAMCTRL_EPF(n) (((n) & 3) << 4)
+
+#define ST7789V_RGBCTRL_CMD 0xb1
+#define ST7789V_RGBCTRL_WO BIT(7)
+#define ST7789V_RGBCTRL_RCM(n) (((n) & 3) << 5)
+#define ST7789V_RGBCTRL_VSYNC_HIGH BIT(3)
+#define ST7789V_RGBCTRL_HSYNC_HIGH BIT(2)
+#define ST7789V_RGBCTRL_PCLK_FALLING BIT(1)
+#define ST7789V_RGBCTRL_DE_LOW BIT(0)
+#define ST7789V_RGBCTRL_VBP(n) ((n) & 0x7f)
+#define ST7789V_RGBCTRL_HBP(n) ((n) & 0x1f)
+
+#define ST7789V_PORCTRL_CMD 0xb2
+#define ST7789V_PORCTRL_IDLE_BP(n) (((n) & 0xf) << 4)
+#define ST7789V_PORCTRL_IDLE_FP(n) ((n) & 0xf)
+#define ST7789V_PORCTRL_PARTIAL_BP(n) (((n) & 0xf) << 4)
+#define ST7789V_PORCTRL_PARTIAL_FP(n) ((n) & 0xf)
+
+#define ST7789V_GCTRL_CMD 0xb7
+#define ST7789V_GCTRL_VGHS(n) (((n) & 7) << 4)
+#define ST7789V_GCTRL_VGLS(n) ((n) & 7)
+
+#define ST7789V_VCOMS_CMD 0xbb
+
+#define ST7789V_LCMCTRL_CMD 0xc0
+#define ST7789V_LCMCTRL_XBGR BIT(5)
+#define ST7789V_LCMCTRL_XMX BIT(3)
+#define ST7789V_LCMCTRL_XMH BIT(2)
+
+#define ST7789V_VDVVRHEN_CMD 0xc2
+#define ST7789V_VDVVRHEN_CMDEN BIT(0)
+
+#define ST7789V_VRHS_CMD 0xc3
+
+#define ST7789V_VDVS_CMD 0xc4
+
+#define ST7789V_FRCTRL2_CMD 0xc6
+
+#define ST7789V_PWCTRL1_CMD 0xd0
+#define ST7789V_PWCTRL1_MAGIC 0xa4
+#define ST7789V_PWCTRL1_AVDD(n) (((n) & 3) << 6)
+#define ST7789V_PWCTRL1_AVCL(n) (((n) & 3) << 4)
+#define ST7789V_PWCTRL1_VDS(n) ((n) & 3)
+
+#define ST7789V_PVGAMCTRL_CMD 0xe0
+#define ST7789V_PVGAMCTRL_JP0(n) (((n) & 3) << 4)
+#define ST7789V_PVGAMCTRL_JP1(n) (((n) & 3) << 4)
+#define ST7789V_PVGAMCTRL_VP0(n) ((n) & 0xf)
+#define ST7789V_PVGAMCTRL_VP1(n) ((n) & 0x3f)
+#define ST7789V_PVGAMCTRL_VP2(n) ((n) & 0x3f)
+#define ST7789V_PVGAMCTRL_VP4(n) ((n) & 0x1f)
+#define ST7789V_PVGAMCTRL_VP6(n) ((n) & 0x1f)
+#define ST7789V_PVGAMCTRL_VP13(n) ((n) & 0xf)
+#define ST7789V_PVGAMCTRL_VP20(n) ((n) & 0x7f)
+#define ST7789V_PVGAMCTRL_VP27(n) ((n) & 7)
+#define ST7789V_PVGAMCTRL_VP36(n) (((n) & 7) << 4)
+#define ST7789V_PVGAMCTRL_VP43(n) ((n) & 0x7f)
+#define ST7789V_PVGAMCTRL_VP50(n) ((n) & 0xf)
+#define ST7789V_PVGAMCTRL_VP57(n) ((n) & 0x1f)
+#define ST7789V_PVGAMCTRL_VP59(n) ((n) & 0x1f)
+#define ST7789V_PVGAMCTRL_VP61(n) ((n) & 0x3f)
+#define ST7789V_PVGAMCTRL_VP62(n) ((n) & 0x3f)
+#define ST7789V_PVGAMCTRL_VP63(n) (((n) & 0xf) << 4)
+
+#define ST7789V_NVGAMCTRL_CMD 0xe1
+#define ST7789V_NVGAMCTRL_JN0(n) (((n) & 3) << 4)
+#define ST7789V_NVGAMCTRL_JN1(n) (((n) & 3) << 4)
+#define ST7789V_NVGAMCTRL_VN0(n) ((n) & 0xf)
+#define ST7789V_NVGAMCTRL_VN1(n) ((n) & 0x3f)
+#define ST7789V_NVGAMCTRL_VN2(n) ((n) & 0x3f)
+#define ST7789V_NVGAMCTRL_VN4(n) ((n) & 0x1f)
+#define ST7789V_NVGAMCTRL_VN6(n) ((n) & 0x1f)
+#define ST7789V_NVGAMCTRL_VN13(n) ((n) & 0xf)
+#define ST7789V_NVGAMCTRL_VN20(n) ((n) & 0x7f)
+#define ST7789V_NVGAMCTRL_VN27(n) ((n) & 7)
+#define ST7789V_NVGAMCTRL_VN36(n) (((n) & 7) << 4)
+#define ST7789V_NVGAMCTRL_VN43(n) ((n) & 0x7f)
+#define ST7789V_NVGAMCTRL_VN50(n) ((n) & 0xf)
+#define ST7789V_NVGAMCTRL_VN57(n) ((n) & 0x1f)
+#define ST7789V_NVGAMCTRL_VN59(n) ((n) & 0x1f)
+#define ST7789V_NVGAMCTRL_VN61(n) ((n) & 0x3f)
+#define ST7789V_NVGAMCTRL_VN62(n) ((n) & 0x3f)
+#define ST7789V_NVGAMCTRL_VN63(n) (((n) & 0xf) << 4)
+
+#define ST7789V_TEST(val, func) \
+ do { \
+ if ((val = (func))) \
+ return val; \
+ } while (0)
+
+#define ST7789V_IDS { 0x85, 0x85, 0x52 }
+#define ST7789V_IDS_SIZE 3
+
+struct st7789_panel_info {
+ const struct drm_display_mode *mode;
+ u32 bus_format;
+ u32 bus_flags;
+ bool invert_mode;
+ bool partial_mode;
+ u16 partial_start;
+ u16 partial_end;
+};
+
+struct st7789v {
+ const struct st7789_panel_info *info;
+ struct spi_device *spi;
+ struct gpio_desc *reset;
+ struct regulator *power;
+ enum drm_panel_orientation orientation;
+ struct device *dev;
+ struct vpl vpl;
+};
+
+enum st7789v_prefix {
+ ST7789V_COMMAND = 0,
+ ST7789V_DATA = 1,
+};
+
+static int st7789v_spi_write(struct st7789v *ctx, enum st7789v_prefix prefix,
+ u8 data)
+{
+ struct spi_transfer xfer = { };
+ u16 txbuf = ((prefix & 1) << 8) | data;
+
+ xfer.tx_buf = &txbuf;
+ xfer.len = sizeof(txbuf);
+
+ return spi_sync_transfer(ctx->spi, &xfer, 1);
+}
+
+static int st7789v_write_command(struct st7789v *ctx, u8 cmd)
+{
+ return st7789v_spi_write(ctx, ST7789V_COMMAND, cmd);
+}
+
+static int st7789v_write_data(struct st7789v *ctx, u8 cmd)
+{
+ return st7789v_spi_write(ctx, ST7789V_DATA, cmd);
+}
+
+static int st7789v_read_data(struct st7789v *ctx, u8 cmd, u8 *buf,
+ unsigned int len)
+{
+ struct spi_transfer xfer[2] = { };
+ struct spi_message msg;
+ u16 txbuf = ((ST7789V_COMMAND & 1) << 8) | cmd;
+ u16 rxbuf[4] = {};
+ u8 bit9 = 0;
+ int ret, i;
+
+ switch (len) {
+ case 1:
+ case 3:
+ case 4:
+ break;
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ spi_message_init(&msg);
+
+ xfer[0].tx_buf = &txbuf;
+ xfer[0].len = sizeof(txbuf);
+ spi_message_add_tail(&xfer[0], &msg);
+
+ xfer[1].rx_buf = rxbuf;
+ xfer[1].len = len * 2;
+ spi_message_add_tail(&xfer[1], &msg);
+
+ ret = spi_sync(ctx->spi, &msg);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < len; i++) {
+ buf[i] = rxbuf[i] >> i | (bit9 << (9 - i));
+ if (i)
+ bit9 = rxbuf[i] & GENMASK(i - 1, 0);
+ }
+
+ return 0;
+}
+
+static int st7789v_check_id(struct st7789v *ctx)
+{
+ const u8 st7789v_ids[ST7789V_IDS_SIZE] = ST7789V_IDS;
+ bool invalid_ids = false;
+ int ret, i;
+ u8 ids[3];
+
+ ret = st7789v_read_data(ctx, MIPI_DCS_GET_DISPLAY_ID, ids, ST7789V_IDS_SIZE);
+ if (ret)
+ return ret;
+printf("%s: %02x %02x %02x\n", __func__, ids[0], ids[1], ids[2]);
+ for (i = 0; i < ST7789V_IDS_SIZE; i++) {
+ if (ids[i] != st7789v_ids[i]) {
+ invalid_ids = true;
+ break;
+ }
+ }
+
+ if (invalid_ids)
+ return -EIO;
+
+ return 0;
+}
+
+static const struct drm_display_mode default_mode = {
+ .clock = 7000,
+ .hdisplay = 240,
+ .hsync_start = 240 + 38,
+ .hsync_end = 240 + 38 + 10,
+ .htotal = 240 + 38 + 10 + 10,
+ .vdisplay = 320,
+ .vsync_start = 320 + 8,
+ .vsync_end = 320 + 8 + 4,
+ .vtotal = 320 + 8 + 4 + 4,
+ .width_mm = 61,
+ .height_mm = 103,
+ .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC,
+};
+
+static const struct drm_display_mode t28cp45tn89_mode = {
+ .clock = 6008,
+ .hdisplay = 240,
+ .hsync_start = 240 + 38,
+ .hsync_end = 240 + 38 + 10,
+ .htotal = 240 + 38 + 10 + 10,
+ .vdisplay = 320,
+ .vsync_start = 320 + 8,
+ .vsync_end = 320 + 8 + 4,
+ .vtotal = 320 + 8 + 4 + 4,
+ .width_mm = 43,
+ .height_mm = 57,
+ .flags = DRM_MODE_FLAG_PVSYNC | DRM_MODE_FLAG_NVSYNC,
+};
+
+static const struct drm_display_mode et028013dma_mode = {
+ .clock = 3000,
+ .hdisplay = 240,
+ .hsync_start = 240 + 38,
+ .hsync_end = 240 + 38 + 10,
+ .htotal = 240 + 38 + 10 + 10,
+ .vdisplay = 320,
+ .vsync_start = 320 + 8,
+ .vsync_end = 320 + 8 + 4,
+ .vtotal = 320 + 8 + 4 + 4,
+ .width_mm = 43,
+ .height_mm = 58,
+ .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC,
+};
+
+static const struct drm_display_mode jt240mhqs_hwt_ek_e3_mode = {
+ .clock = 6000,
+ .hdisplay = 240,
+ .hsync_start = 240 + 28,
+ .hsync_end = 240 + 28 + 10,
+ .htotal = 240 + 28 + 10 + 10,
+ .vdisplay = 280,
+ .vsync_start = 280 + 8,
+ .vsync_end = 280 + 8 + 4,
+ .vtotal = 280 + 8 + 4 + 4,
+ .width_mm = 43,
+ .height_mm = 37,
+ .flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC,
+};
+
+static const struct st7789_panel_info default_panel = {
+ .mode = &default_mode,
+ .invert_mode = true,
+ .bus_format = MEDIA_BUS_FMT_RGB666_1X18,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH |
+ DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE,
+};
+
+static const struct st7789_panel_info t28cp45tn89_panel = {
+ .mode = &t28cp45tn89_mode,
+ .invert_mode = false,
+ .bus_format = MEDIA_BUS_FMT_RGB565_1X16,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH |
+ DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
+};
+
+static const struct st7789_panel_info et028013dma_panel = {
+ .mode = &et028013dma_mode,
+ .invert_mode = true,
+ .bus_format = MEDIA_BUS_FMT_RGB666_1X18,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH |
+ DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE,
+};
+
+static const struct st7789_panel_info jt240mhqs_hwt_ek_e3_panel = {
+ .mode = &jt240mhqs_hwt_ek_e3_mode,
+ .invert_mode = true,
+ .bus_format = MEDIA_BUS_FMT_RGB666_1X18,
+ .bus_flags = DRM_BUS_FLAG_DE_HIGH |
+ DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE,
+ .partial_mode = true,
+ .partial_start = 38,
+ .partial_end = 318,
+};
+
+static int st7789v_get_modes(struct st7789v *ctx,
+ struct display_timings *timings)
+{
+ struct fb_videomode *mode;
+
+ mode = xzalloc(sizeof(*mode));
+
+ drm_display_mode_to_fb_videomode(ctx->info->mode, mode);
+
+ timings->modes = mode;
+ timings->num_modes = 1;
+
+ return 0;
+}
+
+static int st7789v_get_display_info(struct st7789v *ctx,
+ struct drm_display_info *display_info)
+{
+ display_info->bus_flags = ctx->info->bus_flags;
+ display_info->panel_orientation = ctx->orientation;
+
+ return 0;
+}
+
+static int st7789v_prepare(struct st7789v *ctx)
+{
+ u8 mode, pixel_fmt, polarity;
+ int ret;
+
+ if (!ctx->info->partial_mode)
+ mode = ST7789V_RGBCTRL_WO;
+ else
+ mode = 0;
+
+ switch (ctx->info->bus_format) {
+ case MEDIA_BUS_FMT_RGB666_1X18:
+ pixel_fmt = MIPI_DCS_PIXEL_FMT_18BIT;
+ break;
+ case MEDIA_BUS_FMT_RGB565_1X16:
+ pixel_fmt = MIPI_DCS_PIXEL_FMT_16BIT;
+ break;
+ default:
+ dev_err(ctx->dev, "unsupported bus format: %d\n",
+ ctx->info->bus_format);
+ return -EINVAL;
+ }
+
+ pixel_fmt = (pixel_fmt << 4) | pixel_fmt;
+
+ polarity = 0;
+ if (ctx->info->mode->flags & DRM_MODE_FLAG_PVSYNC)
+ polarity |= ST7789V_RGBCTRL_VSYNC_HIGH;
+ if (ctx->info->mode->flags & DRM_MODE_FLAG_PHSYNC)
+ polarity |= ST7789V_RGBCTRL_HSYNC_HIGH;
+ if (ctx->info->bus_flags & DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE)
+ polarity |= ST7789V_RGBCTRL_PCLK_FALLING;
+ if (ctx->info->bus_flags & DRM_BUS_FLAG_DE_LOW)
+ polarity |= ST7789V_RGBCTRL_DE_LOW;
+
+ ret = regulator_enable(ctx->power);
+ if (ret)
+ return ret;
+
+ gpiod_set_value(ctx->reset, 1);
+ mdelay(30);
+ gpiod_set_value(ctx->reset, 0);
+ mdelay(120);
+
+ /*
+ * Avoid failing if the IDs are invalid in case the Rx bus width
+ * description is missing.
+ */
+ ret = st7789v_check_id(ctx);
+ if (ret)
+ dev_warn(ctx->dev, "Unrecognized panel IDs");
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, MIPI_DCS_EXIT_SLEEP_MODE));
+
+ /* We need to wait 120ms after a sleep out command */
+ mdelay(120);
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx,
+ MIPI_DCS_SET_ADDRESS_MODE));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, 0));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx,
+ MIPI_DCS_SET_PIXEL_FORMAT));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, pixel_fmt));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_PORCTRL_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, 0xc));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, 0xc));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, 0));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PORCTRL_IDLE_BP(3) |
+ ST7789V_PORCTRL_IDLE_FP(3)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx,
+ ST7789V_PORCTRL_PARTIAL_BP(3) |
+ ST7789V_PORCTRL_PARTIAL_FP(3)));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_GCTRL_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_GCTRL_VGLS(5) |
+ ST7789V_GCTRL_VGHS(3)));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_VCOMS_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, 0x2b));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_LCMCTRL_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_LCMCTRL_XMH |
+ ST7789V_LCMCTRL_XMX |
+ ST7789V_LCMCTRL_XBGR));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_VDVVRHEN_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_VDVVRHEN_CMDEN));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_VRHS_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, 0xf));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_VDVS_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, 0x20));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_FRCTRL2_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, 0xf));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_PWCTRL1_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PWCTRL1_MAGIC));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PWCTRL1_AVDD(2) |
+ ST7789V_PWCTRL1_AVCL(2) |
+ ST7789V_PWCTRL1_VDS(1)));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_PVGAMCTRL_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP63(0xd)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP1(0xca)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP2(0xe)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP4(8)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP6(9)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP13(7)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP20(0x2d)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP27(0xb) |
+ ST7789V_PVGAMCTRL_VP36(3)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP43(0x3d)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_JP1(3) |
+ ST7789V_PVGAMCTRL_VP50(4)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP57(0xa)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP59(0xa)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP61(0x1b)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_PVGAMCTRL_VP62(0x28)));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_NVGAMCTRL_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN63(0xd)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN1(0xca)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN2(0xf)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN4(8)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN6(8)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN13(7)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN20(0x2e)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN27(0xc) |
+ ST7789V_NVGAMCTRL_VN36(5)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN43(0x40)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_JN1(3) |
+ ST7789V_NVGAMCTRL_VN50(4)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN57(9)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN59(0xb)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN61(0x1b)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_NVGAMCTRL_VN62(0x28)));
+
+ if (ctx->info->invert_mode) {
+ ST7789V_TEST(ret, st7789v_write_command(ctx,
+ MIPI_DCS_ENTER_INVERT_MODE));
+ } else {
+ ST7789V_TEST(ret, st7789v_write_command(ctx,
+ MIPI_DCS_EXIT_INVERT_MODE));
+ }
+
+ if (ctx->info->partial_mode) {
+ u8 area_data[4] = {
+ (ctx->info->partial_start >> 8) & 0xff,
+ (ctx->info->partial_start >> 0) & 0xff,
+ ((ctx->info->partial_end - 1) >> 8) & 0xff,
+ ((ctx->info->partial_end - 1) >> 0) & 0xff,
+ };
+
+ /* Caution: if userspace ever pushes a mode different from the
+ * expected one (i.e., the one advertised by get_modes), we'll
+ * add margins.
+ */
+
+ ST7789V_TEST(ret, st7789v_write_command(
+ ctx, MIPI_DCS_ENTER_PARTIAL_MODE));
+
+ ST7789V_TEST(ret, st7789v_write_command(
+ ctx, MIPI_DCS_SET_PAGE_ADDRESS));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, area_data[0]));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, area_data[1]));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, area_data[2]));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, area_data[3]));
+
+ ST7789V_TEST(ret, st7789v_write_command(
+ ctx, MIPI_DCS_SET_PARTIAL_ROWS));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, area_data[0]));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, area_data[1]));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, area_data[2]));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, area_data[3]));
+ }
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_RAMCTRL_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_RAMCTRL_DM_RGB |
+ ST7789V_RAMCTRL_RM_RGB));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_RAMCTRL_EPF(3) |
+ ST7789V_RAMCTRL_MAGIC));
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, ST7789V_RGBCTRL_CMD));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, mode |
+ ST7789V_RGBCTRL_RCM(2) |
+ polarity));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_RGBCTRL_VBP(8)));
+ ST7789V_TEST(ret, st7789v_write_data(ctx, ST7789V_RGBCTRL_HBP(20)));
+
+ return 0;
+}
+
+static int st7789v_enable(struct st7789v *ctx)
+{
+ return st7789v_write_command(ctx, MIPI_DCS_SET_DISPLAY_ON);
+}
+
+static int st7789v_disable(struct st7789v *ctx)
+{
+ int ret;
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, MIPI_DCS_SET_DISPLAY_OFF));
+
+ return 0;
+}
+
+static int st7789v_unprepare(struct st7789v *ctx)
+{
+ int ret;
+
+ ST7789V_TEST(ret, st7789v_write_command(ctx, MIPI_DCS_ENTER_SLEEP_MODE));
+
+ regulator_disable(ctx->power);
+
+ return 0;
+}
+
+static int ili9341_ioctl(struct vpl *vpl, unsigned int port,
+ unsigned int cmd, void *ptr)
+{
+ struct st7789v *ctx = container_of(vpl, struct st7789v, vpl);
+
+ switch (cmd) {
+ case VPL_PREPARE:
+ return st7789v_prepare(ctx);
+ case VPL_ENABLE:
+ return st7789v_enable(ctx);
+ case VPL_DISABLE:
+ return st7789v_disable(ctx);
+ case VPL_UNPREPARE:
+ return st7789v_unprepare(ctx);
+ case VPL_GET_VIDEOMODES:
+ return st7789v_get_modes(ctx, ptr);
+ case VPL_GET_BUS_FORMAT:
+ *(u32 *)ptr = ctx->info->bus_format;
+ return 0;
+ case VPL_GET_DISPLAY_INFO:
+ return st7789v_get_display_info(ctx, ptr);
+ default:
+ return 0;
+ }
+}
+
+#define spi_setup(spi) spi->master->setup(spi)
+
+static int st7789v_probe(struct device *dev)
+{
+ struct spi_device *spi = to_spi_device(dev);
+ struct st7789v *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ctx->spi = spi;
+ ctx->dev = dev;
+
+ spi->bits_per_word = 9;
+ ret = spi_setup(spi);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "Failed to setup spi\n");
+
+ ctx->info = device_get_match_data(&spi->dev);
+
+ ctx->power = regulator_get(dev, "power");
+ ret = PTR_ERR_OR_ZERO(ctx->power);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to get regulator\n");
+
+ ctx->reset = gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ ret = PTR_ERR_OR_ZERO(ctx->reset);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to get reset line\n");
+
+ ctx->vpl.node = dev->of_node;
+ ctx->vpl.ioctl = ili9341_ioctl;
+
+ return vpl_register(&ctx->vpl);
+}
+
+static const struct of_device_id st7789v_of_match[] = {
+ { .compatible = "sitronix,st7789v", .data = &default_panel },
+ { .compatible = "inanbo,t28cp45tn89-v17", .data = &t28cp45tn89_panel },
+ { .compatible = "edt,et028013dma", .data = &et028013dma_panel },
+ { .compatible = "jasonic,jt240mhqs-hwt-ek-e3",
+ .data = &jt240mhqs_hwt_ek_e3_panel },
+ { }
+};
+MODULE_DEVICE_TABLE(of, st7789v_of_match);
+
+static struct driver st7789v_driver = {
+ .name = "panel-sitronix-st7789v",
+ .of_compatible = st7789v_of_match,
+ .probe = st7789v_probe,
+};
+device_spi_driver(st7789v_driver);
+
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
+MODULE_DESCRIPTION("Sitronix st7789v LCD Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/video/vpl.h b/include/video/vpl.h
index 15711b4701..5ea3d6dcf2 100644
--- a/include/video/vpl.h
+++ b/include/video/vpl.h
@@ -11,6 +11,7 @@
#define VPL_DISABLE 0x67660004
#define VPL_GET_VIDEOMODES 0x67660005
#define VPL_GET_BUS_FORMAT 0x67660006
+#define VPL_GET_DISPLAY_INFO 0x67660007
struct vpl {
int (*ioctl)(struct vpl *, unsigned int port,
--
2.39.5
next prev parent reply other threads:[~2024-09-26 13:16 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-09-26 13:14 [PATCH 00/13] video: Add Rockchip VOP2 support Sascha Hauer
2024-09-26 13:14 ` [PATCH 01/13] clk: rockchip: rk3568: Fix HDMI clocks Sascha Hauer
2024-09-26 14:19 ` Ahmad Fatoum
2024-09-26 13:15 ` [PATCH 02/13] video: add videomode helpers Sascha Hauer
2024-09-26 13:15 ` [PATCH 03/13] media-bus-format: update from kernel Sascha Hauer
2024-09-26 14:20 ` Ahmad Fatoum
2024-09-26 13:15 ` [PATCH 04/13] regmap: add regfield support Sascha Hauer
2024-09-26 13:15 ` [PATCH 05/13] video: add include/video/drm/drm_connector.h Sascha Hauer
2024-09-26 13:15 ` [PATCH 06/13] fb: add fb_rect functions Sascha Hauer
2024-09-26 13:15 ` Sascha Hauer [this message]
2024-09-26 14:16 ` [PATCH 07/13] video: Add Sitronix st7789v panel driver Ahmad Fatoum
2024-09-27 10:15 ` Sascha Hauer
2024-09-26 13:15 ` [PATCH 08/13] video: add dw-hdmi driver Sascha Hauer
2024-09-26 13:15 ` [PATCH 09/13] video: i.MX ipuv3: switch to upstream hdmi driver Sascha Hauer
2024-09-27 6:18 ` Ahmad Fatoum
2024-09-26 13:15 ` [PATCH 10/13] fb: Accept overlay framebuffers without modes Sascha Hauer
2024-09-26 13:15 ` [PATCH 11/13] fb: print more information on devinfo Sascha Hauer
2024-09-27 6:16 ` Ahmad Fatoum
2024-09-26 13:15 ` [PATCH 12/13] ARM: ARM64: implement dma_alloc_writecombine() Sascha Hauer
2024-09-26 14:24 ` Ahmad Fatoum
2024-09-26 13:15 ` [PATCH 13/13] video: Rockchip: Add VOP2 driver Sascha Hauer
2024-09-27 6:13 ` Ahmad Fatoum
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240926-vop2-v1-7-fe0581f2020b@pengutronix.de \
--to=s.hauer@pengutronix.de \
--cc=barebox@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox