[PATCH v2 13/16] video: add Designware MIPI-DSI support

[Ahmad Fatoum <a.fatoum@barebox.org>]

The Designware MIPI-DSI controller is used on both STM32MP1 and Rockchip
RK35x both of which already have a display controller supported in
barebox.

Port the Linux driver in preparation for enabling MIPI-DSI on the
STM32MP1.

Signed-off-by: Ahmad Fatoum <a.fatoum@barebox.org>
---
 drivers/video/Kconfig       |   10 +
 drivers/video/Makefile      |    1 +
 drivers/video/dw_mipi_dsi.c | 1043 +++++++++++++++++++++++++++++++++++
 include/video/dw_mipi_dsi.h |   81 +++
 4 files changed, 1135 insertions(+)
 create mode 100644 drivers/video/dw_mipi_dsi.c
 create mode 100644 include/video/dw_mipi_dsi.h

diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 4ad7cd6b25d4..818ff4a0f1c8 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -215,4 +215,14 @@ config DRIVER_VIDEO_DW_HDMI
 	  controller. To make use of this driver you need platform specific
 	  glue code to be selected as well.
 
+config DRIVER_VIDEO_DW_MIPI_DSI
+	tristate "Designware MIPI-DSI support"
+	select DRIVER_VIDEO_MIPI_DSI
+	select VIDEO_VPL
+	select OFTREE
+	help
+	  Say Y here if you want to enable support for the Designware MIPI-DSI
+	  controller. To make use of this driver you need platform specific
+	  glue code to be selected as well.
+
 endif
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 9a222fb370aa..73d135776102 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -33,5 +33,6 @@ obj-$(CONFIG_DRIVER_VIDEO_EFI_GOP) += efi_gop.o
 obj-$(CONFIG_DRIVER_VIDEO_FB_SSD1307) += ssd1307fb.o
 obj-$(CONFIG_BACKLIGHT_RAVE_SP)	+= rave-sp-backlight.o
 obj-$(CONFIG_DRIVER_VIDEO_DW_HDMI) += dw-hdmi.o
+obj-$(CONFIG_DRIVER_VIDEO_DW_MIPI_DSI) += dw_mipi_dsi.o
 obj-$(CONFIG_DRIVER_VIDEO_BOCHS) += bochs/
 obj-$(CONFIG_DRIVER_VIDEO_ROCKCHIP) += rockchip/
diff --git a/drivers/video/dw_mipi_dsi.c b/drivers/video/dw_mipi_dsi.c
new file mode 100644
index 000000000000..0371806fe893
--- /dev/null
+++ b/drivers/video/dw_mipi_dsi.c
@@ -0,0 +1,1043 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016, Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (C) 2019, STMicroelectronics - All Rights Reserved
+ * Author(s): Philippe Cornu <philippe.cornu@st.com> for STMicroelectronics.
+ *            Yannick Fertre <yannick.fertre@st.com> for STMicroelectronics.
+ *
+ * This generic Synopsys DesignWare MIPI DSI host driver is inspired from
+ * the Linux Kernel driver drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c.
+ */
+
+#include <linux/clk.h>
+#include <linux/printk.h>
+#include <errno.h>
+#include <fb.h>
+#include <of_graph.h>
+#include <linux/io.h>
+#include <linux/bitops.h>
+#include <clock.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/time.h>
+#include <linux/reset.h>
+#include <video/vpl.h>
+#include <video/videomode.h>
+#include <video/mipi_dsi.h>
+#include <video/dw_mipi_dsi.h>
+
+#define DRM_DEV_ERROR dev_err
+#define DRM_DEBUG_DRIVER pr_debug
+
+#define HWVER_131			0x31333100	/* IP version 1.31 */
+
+#define DSI_VERSION			0x00
+#define VERSION				GENMASK(31, 8)
+
+#define DSI_PWR_UP			0x04
+#define RESET				0
+#define POWERUP				BIT(0)
+
+#define DSI_CLKMGR_CFG			0x08
+#define TO_CLK_DIVISION(div)		(((div) & 0xff) << 8)
+#define TX_ESC_CLK_DIVISION(div)	((div) & 0xff)
+
+#define DSI_DPI_VCID			0x0c
+#define DPI_VCID(vcid)			((vcid) & 0x3)
+
+#define DSI_DPI_COLOR_CODING		0x10
+#define LOOSELY18_EN			BIT(8)
+#define DPI_COLOR_CODING_16BIT_1	0x0
+#define DPI_COLOR_CODING_16BIT_2	0x1
+#define DPI_COLOR_CODING_16BIT_3	0x2
+#define DPI_COLOR_CODING_18BIT_1	0x3
+#define DPI_COLOR_CODING_18BIT_2	0x4
+#define DPI_COLOR_CODING_24BIT		0x5
+
+#define DSI_DPI_CFG_POL			0x14
+#define COLORM_ACTIVE_LOW		BIT(4)
+#define SHUTD_ACTIVE_LOW		BIT(3)
+#define HSYNC_ACTIVE_LOW		BIT(2)
+#define VSYNC_ACTIVE_LOW		BIT(1)
+#define DATAEN_ACTIVE_LOW		BIT(0)
+
+#define DSI_DPI_LP_CMD_TIM		0x18
+#define OUTVACT_LPCMD_TIME(p)		(((p) & 0xff) << 16)
+#define INVACT_LPCMD_TIME(p)		((p) & 0xff)
+
+#define DSI_DBI_VCID			0x1c
+#define DSI_DBI_CFG			0x20
+#define DSI_DBI_PARTITIONING_EN		0x24
+#define DSI_DBI_CMDSIZE			0x28
+
+#define DSI_PCKHDL_CFG			0x2c
+#define CRC_RX_EN			BIT(4)
+#define ECC_RX_EN			BIT(3)
+#define BTA_EN				BIT(2)
+#define EOTP_RX_EN			BIT(1)
+#define EOTP_TX_EN			BIT(0)
+
+#define DSI_GEN_VCID			0x30
+
+#define DSI_MODE_CFG			0x34
+#define ENABLE_VIDEO_MODE		0
+#define ENABLE_CMD_MODE			BIT(0)
+
+#define DSI_VID_MODE_CFG		0x38
+#define ENABLE_LOW_POWER		(0x3f << 8)
+#define ENABLE_LOW_POWER_MASK		(0x3f << 8)
+#define VID_MODE_TYPE_NON_BURST_SYNC_PULSES	0x0
+#define VID_MODE_TYPE_NON_BURST_SYNC_EVENTS	0x1
+#define VID_MODE_TYPE_BURST			0x2
+#define VID_MODE_TYPE_MASK			0x3
+#define ENABLE_LOW_POWER_CMD		BIT(15)
+#define VID_MODE_VPG_ENABLE		BIT(16)
+#define VID_MODE_VPG_MODE		BIT(20)
+#define VID_MODE_VPG_HORIZONTAL		BIT(24)
+
+#define DSI_VID_PKT_SIZE		0x3c
+#define VID_PKT_SIZE(p)			((p) & 0x3fff)
+
+#define DSI_VID_NUM_CHUNKS		0x40
+#define VID_NUM_CHUNKS(c)		((c) & 0x1fff)
+
+#define DSI_VID_NULL_SIZE		0x44
+#define VID_NULL_SIZE(b)		((b) & 0x1fff)
+
+#define DSI_VID_HSA_TIME		0x48
+#define DSI_VID_HBP_TIME		0x4c
+#define DSI_VID_HLINE_TIME		0x50
+#define DSI_VID_VSA_LINES		0x54
+#define DSI_VID_VBP_LINES		0x58
+#define DSI_VID_VFP_LINES		0x5c
+#define DSI_VID_VACTIVE_LINES		0x60
+#define DSI_EDPI_CMD_SIZE		0x64
+
+#define DSI_CMD_MODE_CFG		0x68
+#define MAX_RD_PKT_SIZE_LP		BIT(24)
+#define DCS_LW_TX_LP			BIT(19)
+#define DCS_SR_0P_TX_LP			BIT(18)
+#define DCS_SW_1P_TX_LP			BIT(17)
+#define DCS_SW_0P_TX_LP			BIT(16)
+#define GEN_LW_TX_LP			BIT(14)
+#define GEN_SR_2P_TX_LP			BIT(13)
+#define GEN_SR_1P_TX_LP			BIT(12)
+#define GEN_SR_0P_TX_LP			BIT(11)
+#define GEN_SW_2P_TX_LP			BIT(10)
+#define GEN_SW_1P_TX_LP			BIT(9)
+#define GEN_SW_0P_TX_LP			BIT(8)
+#define ACK_RQST_EN			BIT(1)
+#define TEAR_FX_EN			BIT(0)
+
+#define CMD_MODE_ALL_LP			(MAX_RD_PKT_SIZE_LP | \
+					 DCS_LW_TX_LP | \
+					 DCS_SR_0P_TX_LP | \
+					 DCS_SW_1P_TX_LP | \
+					 DCS_SW_0P_TX_LP | \
+					 GEN_LW_TX_LP | \
+					 GEN_SR_2P_TX_LP | \
+					 GEN_SR_1P_TX_LP | \
+					 GEN_SR_0P_TX_LP | \
+					 GEN_SW_2P_TX_LP | \
+					 GEN_SW_1P_TX_LP | \
+					 GEN_SW_0P_TX_LP)
+
+#define DSI_GEN_HDR			0x6c
+#define DSI_GEN_PLD_DATA		0x70
+
+#define DSI_CMD_PKT_STATUS		0x74
+#define GEN_RD_CMD_BUSY			BIT(6)
+#define GEN_PLD_R_FULL			BIT(5)
+#define GEN_PLD_R_EMPTY			BIT(4)
+#define GEN_PLD_W_FULL			BIT(3)
+#define GEN_PLD_W_EMPTY			BIT(2)
+#define GEN_CMD_FULL			BIT(1)
+#define GEN_CMD_EMPTY			BIT(0)
+
+#define DSI_TO_CNT_CFG			0x78
+#define HSTX_TO_CNT(p)			(((p) & 0xffff) << 16)
+#define LPRX_TO_CNT(p)			((p) & 0xffff)
+
+#define DSI_HS_RD_TO_CNT		0x7c
+#define DSI_LP_RD_TO_CNT		0x80
+#define DSI_HS_WR_TO_CNT		0x84
+#define DSI_LP_WR_TO_CNT		0x88
+#define DSI_BTA_TO_CNT			0x8c
+
+#define DSI_LPCLK_CTRL			0x94
+#define AUTO_CLKLANE_CTRL		BIT(1)
+#define PHY_TXREQUESTCLKHS		BIT(0)
+
+#define DSI_PHY_TMR_LPCLK_CFG		0x98
+#define PHY_CLKHS2LP_TIME(lbcc)		(((lbcc) & 0x3ff) << 16)
+#define PHY_CLKLP2HS_TIME(lbcc)		((lbcc) & 0x3ff)
+
+#define DSI_PHY_TMR_CFG			0x9c
+#define PHY_HS2LP_TIME(lbcc)		(((lbcc) & 0xff) << 24)
+#define PHY_LP2HS_TIME(lbcc)		(((lbcc) & 0xff) << 16)
+#define MAX_RD_TIME(lbcc)		((lbcc) & 0x7fff)
+#define PHY_HS2LP_TIME_V131(lbcc)	(((lbcc) & 0x3ff) << 16)
+#define PHY_LP2HS_TIME_V131(lbcc)	((lbcc) & 0x3ff)
+
+#define DSI_PHY_RSTZ			0xa0
+#define PHY_DISFORCEPLL			0
+#define PHY_ENFORCEPLL			BIT(3)
+#define PHY_DISABLECLK			0
+#define PHY_ENABLECLK			BIT(2)
+#define PHY_RSTZ			0
+#define PHY_UNRSTZ			BIT(1)
+#define PHY_SHUTDOWNZ			0
+#define PHY_UNSHUTDOWNZ			BIT(0)
+
+#define DSI_PHY_IF_CFG			0xa4
+#define PHY_STOP_WAIT_TIME(cycle)	(((cycle) & 0xff) << 8)
+#define N_LANES(n)			(((n) - 1) & 0x3)
+
+#define DSI_PHY_ULPS_CTRL		0xa8
+#define DSI_PHY_TX_TRIGGERS		0xac
+
+#define DSI_PHY_STATUS			0xb0
+#define PHY_STOP_STATE_CLK_LANE		BIT(2)
+#define PHY_LOCK			BIT(0)
+
+#define DSI_PHY_TST_CTRL0		0xb4
+#define PHY_TESTCLK			BIT(1)
+#define PHY_UNTESTCLK			0
+#define PHY_TESTCLR			BIT(0)
+#define PHY_UNTESTCLR			0
+
+#define DSI_PHY_TST_CTRL1		0xb8
+#define PHY_TESTEN			BIT(16)
+#define PHY_UNTESTEN			0
+#define PHY_TESTDOUT(n)			(((n) & 0xff) << 8)
+#define PHY_TESTDIN(n)			((n) & 0xff)
+
+#define DSI_INT_ST0			0xbc
+#define DSI_INT_ST1			0xc0
+#define DSI_INT_MSK0			0xc4
+#define DSI_INT_MSK1			0xc8
+
+#define DSI_PHY_TMR_RD_CFG		0xf4
+#define MAX_RD_TIME_V131(lbcc)		((lbcc) & 0x7fff)
+
+#define PHY_STATUS_TIMEOUT_US		10000
+#define CMD_PKT_STATUS_TIMEOUT_US	20000
+
+enum vpg_mode {
+	VPG_DISABLED,
+	VPG_BER,
+	VPG_COLORS_V,
+	VPG_COLORS_H,
+};
+
+struct dw_mipi_dsi {
+	struct mipi_dsi_host dsi_host;
+	struct device *dev;
+	void __iomem *base;
+	struct vpl vpl;
+	struct vpl_bridge *panel_bridge;
+
+	struct clk *pclk;
+
+	unsigned int lane_mbps; /* per lane */
+	u32 channel;
+	u32 lanes;
+	u32 format;
+	unsigned long mode_flags;
+	struct fb_videomode *mode;
+
+	int vpg_mode;
+
+	const struct dw_mipi_dsi_plat_data *plat_data;
+};
+
+/*
+ * The controller should generate 2 frames before
+ * preparing the peripheral.
+ */
+static void dw_mipi_dsi_wait_for_two_frames(const struct drm_display_mode *mode)
+{
+	int refresh, two_frames;
+
+	refresh = drm_mode_vrefresh(mode);
+	two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2;
+	mdelay(two_frames);
+}
+
+static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host)
+{
+	return container_of(host, struct dw_mipi_dsi, dsi_host);
+}
+
+static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val)
+{
+	writel(val, dsi->base + reg);
+}
+
+static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg)
+{
+	return readl(dsi->base + reg);
+}
+
+static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host,
+				   struct mipi_dsi_device *device)
+{
+	struct dw_mipi_dsi *dsi = host_to_dsi(host);
+	const struct dw_mipi_dsi_plat_data *pdata = dsi->plat_data;
+	struct vpl_bridge *bridge;
+	int ret;
+
+	if (device->lanes > dsi->plat_data->max_data_lanes) {
+		dev_err(dsi->dev, "the number of data lanes(%u) is too many\n",
+			device->lanes);
+		return -EINVAL;
+	}
+
+	dsi->lanes = device->lanes;
+	dsi->channel = device->channel;
+	dsi->format = device->format;
+	dsi->mode_flags = device->mode_flags;
+
+	bridge = devm_vpl_of_get_bridge(dsi->dev, dsi->dev->of_node, 1, 0);
+	if (IS_ERR(bridge))
+		return PTR_ERR(bridge);
+
+	dsi->panel_bridge = bridge;
+
+	if (pdata->host_ops && pdata->host_ops->attach) {
+		ret = pdata->host_ops->attach(pdata->priv_data, device);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static void dw_mipi_message_config(struct dw_mipi_dsi *dsi,
+				   const struct mipi_dsi_msg *msg)
+{
+	bool lpm = msg->flags & MIPI_DSI_MSG_USE_LPM;
+	u32 val = 0;
+
+	/*
+	 * TODO dw drv improvements
+	 * largest packet sizes during hfp or during vsa/vpb/vfp
+	 * should be computed according to byte lane, lane number and only
+	 * if sending lp cmds in high speed is enable (PHY_TXREQUESTCLKHS)
+	 */
+	dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(16)
+		  | INVACT_LPCMD_TIME(4));
+
+	if (msg->flags & MIPI_DSI_MSG_REQ_ACK)
+		val |= ACK_RQST_EN;
+	if (lpm)
+		val |= CMD_MODE_ALL_LP;
+
+	dsi_write(dsi, DSI_CMD_MODE_CFG, val);
+
+	val = dsi_read(dsi, DSI_VID_MODE_CFG);
+	if (lpm)
+		val |= ENABLE_LOW_POWER_CMD;
+	else
+		val &= ~ENABLE_LOW_POWER_CMD;
+	dsi_write(dsi, DSI_VID_MODE_CFG, val);
+}
+
+static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 hdr_val)
+{
+	int ret;
+	u32 val, mask;
+
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
+				 val, !(val & GEN_CMD_FULL),
+				 CMD_PKT_STATUS_TIMEOUT_US);
+	if (ret) {
+		dev_err(dsi->dev, "failed to get available command FIFO\n");
+		return ret;
+	}
+
+	dsi_write(dsi, DSI_GEN_HDR, hdr_val);
+
+	mask = GEN_CMD_EMPTY | GEN_PLD_W_EMPTY;
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
+				 val, (val & mask) == mask,
+				 CMD_PKT_STATUS_TIMEOUT_US);
+	if (ret) {
+		dev_err(dsi->dev, "failed to write command FIFO\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int dw_mipi_dsi_write(struct dw_mipi_dsi *dsi,
+			     const struct mipi_dsi_packet *packet)
+{
+	const u8 *tx_buf = packet->payload;
+	int len = packet->payload_length, pld_data_bytes = sizeof(u32), ret;
+	__le32 word;
+	u32 val;
+
+	while (len) {
+		if (len < pld_data_bytes) {
+			word = 0;
+			memcpy(&word, tx_buf, len);
+			dsi_write(dsi, DSI_GEN_PLD_DATA, le32_to_cpu(word));
+			len = 0;
+		} else {
+			memcpy(&word, tx_buf, pld_data_bytes);
+			dsi_write(dsi, DSI_GEN_PLD_DATA, le32_to_cpu(word));
+			tx_buf += pld_data_bytes;
+			len -= pld_data_bytes;
+		}
+
+		ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
+					 val, !(val & GEN_PLD_W_FULL),
+					 CMD_PKT_STATUS_TIMEOUT_US);
+		if (ret) {
+			dev_err(dsi->dev,
+				"failed to get available write payload FIFO\n");
+			return ret;
+		}
+	}
+
+	word = 0;
+	memcpy(&word, packet->header, sizeof(packet->header));
+	return dw_mipi_dsi_gen_pkt_hdr_write(dsi, le32_to_cpu(word));
+}
+
+static int dw_mipi_dsi_read(struct dw_mipi_dsi *dsi,
+			    const struct mipi_dsi_msg *msg)
+{
+	int i, j, ret, len = msg->rx_len;
+	u8 *buf = msg->rx_buf;
+	u32 val;
+
+	/* Wait end of the read operation */
+	ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
+				 val, !(val & GEN_RD_CMD_BUSY),
+				 CMD_PKT_STATUS_TIMEOUT_US);
+	if (ret) {
+		dev_err(dsi->dev, "Timeout during read operation\n");
+		return ret;
+	}
+
+	for (i = 0; i < len; i += 4) {
+		/* Read fifo must not be empty before all bytes are read */
+		ret = readl_poll_timeout(dsi->base + DSI_CMD_PKT_STATUS,
+					 val, !(val & GEN_PLD_R_EMPTY),
+					 CMD_PKT_STATUS_TIMEOUT_US);
+		if (ret) {
+			dev_err(dsi->dev, "Read payload FIFO is empty\n");
+			return ret;
+		}
+
+		val = dsi_read(dsi, DSI_GEN_PLD_DATA);
+		for (j = 0; j < 4 && j + i < len; j++)
+			buf[i + j] = val >> (8 * j);
+	}
+
+	return ret;
+}
+
+static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host,
+					 const struct mipi_dsi_msg *msg)
+{
+	struct dw_mipi_dsi *dsi = host_to_dsi(host);
+	struct mipi_dsi_packet packet;
+	int ret, nb_bytes;
+
+	ret = mipi_dsi_create_packet(&packet, msg);
+	if (ret) {
+		dev_err(dsi->dev, "failed to create packet: %d\n", ret);
+		return ret;
+	}
+
+	dw_mipi_message_config(dsi, msg);
+
+	ret = dw_mipi_dsi_write(dsi, &packet);
+	if (ret)
+		return ret;
+
+	if (msg->rx_buf && msg->rx_len) {
+		ret = dw_mipi_dsi_read(dsi, msg);
+		if (ret)
+			return ret;
+		nb_bytes = msg->rx_len;
+	} else {
+		nb_bytes = packet.size;
+	}
+
+	return nb_bytes;
+}
+
+static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = {
+	.attach = dw_mipi_dsi_host_attach,
+	.transfer = dw_mipi_dsi_host_transfer,
+};
+
+static void vpg_update(struct dw_mipi_dsi *dsi, u32 *val)
+{
+	*val &= ~(VID_MODE_VPG_ENABLE | VID_MODE_VPG_HORIZONTAL |
+		      VID_MODE_VPG_MODE);
+
+	if (dsi->vpg_mode != VPG_DISABLED) {
+		*val |= VID_MODE_VPG_ENABLE;
+		*val |= dsi->vpg_mode == VPG_COLORS_H ?
+			VID_MODE_VPG_HORIZONTAL : 0;
+		*val |= dsi->vpg_mode == VPG_BER ? VID_MODE_VPG_MODE : 0;
+	}
+}
+
+static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi)
+{
+	u32 val;
+
+	/*
+	 * TODO dw drv improvements
+	 * enabling low power is panel-dependent, we should use the
+	 * panel configuration here...
+	 */
+	val = ENABLE_LOW_POWER;
+
+	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
+		val |= VID_MODE_TYPE_BURST;
+	else if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_PULSES;
+	else
+		val |= VID_MODE_TYPE_NON_BURST_SYNC_EVENTS;
+
+	vpg_update(dsi, &val);
+
+	dsi_write(dsi, DSI_VID_MODE_CFG, val);
+}
+
+static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi,
+				 unsigned long mode_flags)
+{
+	u32 val;
+
+	dsi_write(dsi, DSI_PWR_UP, RESET);
+
+	if (mode_flags & MIPI_DSI_MODE_VIDEO) {
+		dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE);
+		dw_mipi_dsi_video_mode_config(dsi);
+	} else {
+		dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
+	}
+
+	val = PHY_TXREQUESTCLKHS;
+	if (dsi->mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS)
+		val |= AUTO_CLKLANE_CTRL;
+	dsi_write(dsi, DSI_LPCLK_CTRL, val);
+
+	dsi_write(dsi, DSI_PWR_UP, POWERUP);
+}
+
+static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi)
+{
+	dsi_write(dsi, DSI_PWR_UP, RESET);
+	dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ);
+}
+
+static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi)
+{
+	const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
+	unsigned int esc_rate; /* in MHz */
+	u32 esc_clk_division;
+	int ret;
+
+	/*
+	 * The maximum permitted escape clock is 20MHz and it is derived from
+	 * lanebyteclk, which is running at "lane_mbps / 8".
+	 */
+	if (phy_ops->get_esc_clk_rate) {
+		ret = phy_ops->get_esc_clk_rate(dsi->plat_data->priv_data,
+						&esc_rate);
+		if (ret)
+			DRM_DEBUG_DRIVER("Phy get_esc_clk_rate() failed\n");
+	} else
+		esc_rate = 20; /* Default to 20MHz */
+
+	/*
+	 * We want :
+	 *     (lane_mbps >> 3) / esc_clk_division < X
+	 * which is:
+	 *     (lane_mbps >> 3) / X > esc_clk_division
+	 */
+	esc_clk_division = (dsi->lane_mbps >> 3) / esc_rate + 1;
+
+	dsi_write(dsi, DSI_PWR_UP, RESET);
+
+	/*
+	 * TODO dw drv improvements
+	 * timeout clock division should be computed with the
+	 * high speed transmission counter timeout and byte lane...
+	 */
+	dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVISION(0) |
+		  TX_ESC_CLK_DIVISION(esc_clk_division));
+}
+
+static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi,
+				   const struct drm_display_mode *mode)
+{
+	u32 val = 0, color = 0;
+
+	switch (dsi->format) {
+	case MIPI_DSI_FMT_RGB888:
+		color = DPI_COLOR_CODING_24BIT;
+		break;
+	case MIPI_DSI_FMT_RGB666:
+		color = DPI_COLOR_CODING_18BIT_2 | LOOSELY18_EN;
+		break;
+	case MIPI_DSI_FMT_RGB666_PACKED:
+		color = DPI_COLOR_CODING_18BIT_1;
+		break;
+	case MIPI_DSI_FMT_RGB565:
+		color = DPI_COLOR_CODING_16BIT_1;
+		break;
+	}
+
+	if (mode->flags & DRM_MODE_FLAG_NVSYNC)
+		val |= VSYNC_ACTIVE_LOW;
+	if (mode->flags & DRM_MODE_FLAG_NHSYNC)
+		val |= HSYNC_ACTIVE_LOW;
+
+	dsi_write(dsi, DSI_DPI_VCID, DPI_VCID(dsi->channel));
+	dsi_write(dsi, DSI_DPI_COLOR_CODING, color);
+	dsi_write(dsi, DSI_DPI_CFG_POL, val);
+}
+
+static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi)
+{
+	u32 val = CRC_RX_EN | ECC_RX_EN | BTA_EN | EOTP_TX_EN;
+
+	if (dsi->mode_flags & MIPI_DSI_MODE_NO_EOT_PACKET)
+		val &= ~EOTP_TX_EN;
+
+	dsi_write(dsi, DSI_PCKHDL_CFG, val);
+}
+
+static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi,
+					    const struct drm_display_mode *mode)
+{
+	/*
+	 * TODO dw drv improvements
+	 * only burst mode is supported here. For non-burst video modes,
+	 * we should compute DSI_VID_PKT_SIZE, DSI_VCCR.NUMC &
+	 * DSI_VNPCR.NPSIZE... especially because this driver supports
+	 * non-burst video modes, see dw_mipi_dsi_video_mode_config()...
+	 */
+	dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay));
+}
+
+static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi)
+{
+	/*
+	 * TODO dw drv improvements
+	 * compute high speed transmission counter timeout according
+	 * to the timeout clock division (TO_CLK_DIVISION) and byte lane...
+	 */
+	dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(0) | LPRX_TO_CNT(0));
+	/*
+	 * TODO dw drv improvements
+	 * the Bus-Turn-Around Timeout Counter should be computed
+	 * according to byte lane...
+	 */
+	dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00);
+	dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE);
+}
+
+static const u32 minimum_lbccs[] = {10, 5, 4, 3};
+
+static inline u32 dw_mipi_dsi_get_minimum_lbcc(struct dw_mipi_dsi *dsi)
+{
+	return minimum_lbccs[dsi->lanes - 1];
+}
+
+/* Get lane byte clock cycles. */
+static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi,
+					   const struct drm_display_mode *mode,
+					   u32 hcomponent)
+{
+	u32 frac, lbcc, minimum_lbcc;
+	int bpp;
+
+	if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) {
+		/* lbcc based on lane_mbps */
+		lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8;
+	} else {
+		/* lbcc based on pixel clock rate */
+		bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
+		if (bpp < 0) {
+			dev_err(dsi->dev, "failed to get bpp\n");
+			return 0;
+		}
+
+		lbcc = div_u64((u64)hcomponent * mode->clock * bpp, dsi->lanes * 8);
+	}
+
+	frac = lbcc % mode->clock;
+	lbcc = lbcc / mode->clock;
+	if (frac)
+		lbcc++;
+
+	minimum_lbcc = dw_mipi_dsi_get_minimum_lbcc(dsi);
+
+	if (lbcc < minimum_lbcc)
+		lbcc = minimum_lbcc;
+
+	return lbcc;
+}
+
+static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi,
+					  const struct drm_display_mode *mode)
+{
+	u32 htotal, hsa, hbp, lbcc;
+
+	htotal = mode->htotal;
+	hsa = mode->hsync_end - mode->hsync_start;
+	hbp = mode->htotal - mode->hsync_end;
+
+	/*
+	 * TODO dw drv improvements
+	 * computations below may be improved...
+	 */
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, htotal);
+	dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc);
+
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hsa);
+	dsi_write(dsi, DSI_VID_HSA_TIME, lbcc);
+
+	lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, mode, hbp);
+	dsi_write(dsi, DSI_VID_HBP_TIME, lbcc);
+}
+
+static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi,
+					const struct drm_display_mode *mode)
+{
+	u32 vactive, vsa, vfp, vbp;
+
+	vactive = mode->vdisplay;
+	vsa = mode->vsync_end - mode->vsync_start;
+	vfp = mode->vsync_start - mode->vdisplay;
+	vbp = mode->vtotal - mode->vsync_end;
+
+	dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive);
+	dsi_write(dsi, DSI_VID_VSA_LINES, vsa);
+	dsi_write(dsi, DSI_VID_VFP_LINES, vfp);
+	dsi_write(dsi, DSI_VID_VBP_LINES, vbp);
+}
+
+static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi)
+{
+	const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
+	struct dw_mipi_dsi_dphy_timing timing;
+	u32 hw_version;
+	int ret;
+
+	ret = phy_ops->get_timing(dsi->plat_data->priv_data,
+				  dsi->lane_mbps, &timing);
+	if (ret)
+		DRM_DEV_ERROR(dsi->dev, "Retrieving phy timings failed\n");
+
+	/*
+	 * TODO dw drv improvements
+	 * data & clock lane timers should be computed according to panel
+	 * blankings and to the automatic clock lane control mode...
+	 * note: DSI_PHY_TMR_CFG.MAX_RD_TIME should be in line with
+	 * DSI_CMD_MODE_CFG.MAX_RD_PKT_SIZE_LP (see CMD_MODE_ALL_LP)
+	 */
+
+	hw_version = dsi_read(dsi, DSI_VERSION) & VERSION;
+
+	if (hw_version >= HWVER_131) {
+		dsi_write(dsi, DSI_PHY_TMR_CFG,
+			  PHY_HS2LP_TIME_V131(timing.data_hs2lp) |
+			  PHY_LP2HS_TIME_V131(timing.data_lp2hs));
+		dsi_write(dsi, DSI_PHY_TMR_RD_CFG, MAX_RD_TIME_V131(10000));
+	} else {
+		dsi_write(dsi, DSI_PHY_TMR_CFG,
+			  PHY_HS2LP_TIME(timing.data_hs2lp) |
+			  PHY_LP2HS_TIME(timing.data_lp2hs) |
+			  MAX_RD_TIME(10000));
+	}
+
+	dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG,
+		  PHY_CLKHS2LP_TIME(timing.clk_hs2lp) |
+		  PHY_CLKLP2HS_TIME(timing.clk_lp2hs));
+}
+
+static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi)
+{
+	/*
+	 * TODO dw drv improvements
+	 * stop wait time should be the maximum between host dsi
+	 * and panel stop wait times
+	 */
+	dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) |
+		  N_LANES(dsi->lanes));
+}
+
+static void dw_mipi_dsi_dphy_init(struct dw_mipi_dsi *dsi)
+{
+	/* Clear PHY state */
+	dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK
+		  | PHY_RSTZ | PHY_SHUTDOWNZ);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLR);
+	dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLR);
+}
+
+static void dw_mipi_dsi_dphy_enable(struct dw_mipi_dsi *dsi)
+{
+	u32 val;
+	int ret;
+
+	dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK |
+		  PHY_UNRSTZ | PHY_UNSHUTDOWNZ);
+
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS, val,
+				 val & PHY_LOCK, PHY_STATUS_TIMEOUT_US);
+	if (ret)
+		DRM_DEBUG_DRIVER("failed to wait phy lock state\n");
+
+	ret = readl_poll_timeout(dsi->base + DSI_PHY_STATUS,
+				 val, val & PHY_STOP_STATE_CLK_LANE,
+				 PHY_STATUS_TIMEOUT_US);
+	if (ret)
+		DRM_DEBUG_DRIVER("failed to wait phy clk lane stop state\n");
+}
+
+static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi)
+{
+	dsi_read(dsi, DSI_INT_ST0);
+	dsi_read(dsi, DSI_INT_ST1);
+	dsi_write(dsi, DSI_INT_MSK0, 0);
+	dsi_write(dsi, DSI_INT_MSK1, 0);
+}
+
+static void dw_mipi_dsi_bridge_post_atomic_disable(struct dw_mipi_dsi *dsi)
+{
+	const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
+
+	/*
+	 * Switch to command mode before panel-bridge post_disable &
+	 * panel unprepare.
+	 * Note: panel-bridge disable & panel disable has been called
+	 * before by the drm framework.
+	 */
+	dw_mipi_dsi_set_mode(dsi, 0);
+
+	if (phy_ops->power_off)
+		phy_ops->power_off(dsi->plat_data->priv_data);
+
+	dw_mipi_dsi_disable(dsi);
+	clk_disable_unprepare(dsi->pclk);
+}
+
+static unsigned int dw_mipi_dsi_get_lanes(struct dw_mipi_dsi *dsi)
+{
+	/* only single-dsi supported, so no other instance to consider */
+	return dsi->lanes;
+}
+
+static void dw_mipi_dsi_mode_set(struct dw_mipi_dsi *dsi,
+				 const struct drm_display_mode *adjusted_mode)
+{
+	const struct dw_mipi_dsi_phy_ops *phy_ops = dsi->plat_data->phy_ops;
+	void *priv_data = dsi->plat_data->priv_data;
+	int ret;
+	u32 lanes = dw_mipi_dsi_get_lanes(dsi);
+
+	clk_prepare_enable(dsi->pclk);
+
+	ret = phy_ops->get_lane_mbps(priv_data, adjusted_mode, dsi->mode_flags,
+				     lanes, dsi->format, &dsi->lane_mbps);
+	if (ret)
+		DRM_DEBUG_DRIVER("Phy get_lane_mbps() failed\n");
+
+	dw_mipi_dsi_init(dsi);
+	dw_mipi_dsi_dpi_config(dsi, adjusted_mode);
+	dw_mipi_dsi_packet_handler_config(dsi);
+	dw_mipi_dsi_video_mode_config(dsi);
+	dw_mipi_dsi_video_packet_config(dsi, adjusted_mode);
+	dw_mipi_dsi_command_mode_config(dsi);
+	dw_mipi_dsi_line_timer_config(dsi, adjusted_mode);
+	dw_mipi_dsi_vertical_timing_config(dsi, adjusted_mode);
+
+	dw_mipi_dsi_dphy_init(dsi);
+	dw_mipi_dsi_dphy_timing_config(dsi);
+	dw_mipi_dsi_dphy_interface_config(dsi);
+
+	dw_mipi_dsi_clear_err(dsi);
+
+	ret = phy_ops->init(priv_data);
+	if (ret)
+		DRM_DEBUG_DRIVER("Phy init() failed\n");
+
+	dw_mipi_dsi_dphy_enable(dsi);
+
+	dw_mipi_dsi_wait_for_two_frames(adjusted_mode);
+
+	/* Switch to cmd mode for panel-bridge pre_enable & panel prepare */
+	dw_mipi_dsi_set_mode(dsi, 0);
+
+	if (phy_ops->power_on)
+		phy_ops->power_on(dsi->plat_data->priv_data);
+}
+
+static int vpg_param_set(struct param_d *param, void *data)
+{
+	struct dw_mipi_dsi *dsi = data;
+	u32 mode_cfg;
+
+	mode_cfg = dsi_read(dsi, DSI_VID_MODE_CFG);
+
+	vpg_update(dsi, &mode_cfg);
+
+	dsi_write(dsi, DSI_VID_MODE_CFG, mode_cfg);
+
+	return 0;
+}
+
+static int dw_mipi_dsi_ioctl(struct vpl *vpl, unsigned int port,
+			 unsigned int cmd, void *data)
+{
+	struct dw_mipi_dsi *dsi = container_of(vpl, struct dw_mipi_dsi, vpl);
+	struct drm_display_mode mode = {};
+
+	switch (cmd) {
+	case VPL_ENABLE:
+		/* Switch to video mode for panel-bridge enable & panel enable */
+		dw_mipi_dsi_set_mode(dsi, MIPI_DSI_MODE_VIDEO);
+		break;
+	case VPL_DISABLE:
+		dw_mipi_dsi_bridge_post_atomic_disable(dsi);
+		break;
+	case VPL_PREPARE:
+		/*
+		 * We store this to simplify debugging by allowing:
+		 *   vpl->ioctl(vpl, output_port, VPL_DISABLE, NULL);
+		 *   vpl->ioctl(vpl, output_port, VPL_PREPARE, NULL);
+		 * to possibly get an already enabled display back into command mode.
+		 */
+		if (data)
+			dsi->mode = data;
+		if (!dsi->mode)
+			return -EINVAL;
+		fb_videomode_to_drm_display_mode(dsi->mode, &mode);
+		dw_mipi_dsi_mode_set(dsi, &mode);
+		break;
+	}
+
+	/* Probes should have occured by now */
+	WARN_ON(!dsi->panel_bridge);
+
+	return vpl_bridge_ioctl(dsi->panel_bridge, cmd, data);
+}
+
+static const char *vpg_modes[] = {
+	[VPG_DISABLED]	= "disabled",
+	[VPG_BER]	= "ber",
+	[VPG_COLORS_V]	= "colors",
+	[VPG_COLORS_H]	= "colors-horizontal",
+};
+
+static struct dw_mipi_dsi *
+dw_mipi_dsi_probe(struct device *dev,
+		  const struct dw_mipi_dsi_plat_data *plat_data)
+{
+	struct dw_mipi_dsi *dsi;
+	struct reset_control *apb_rst;
+	struct resource *iores;
+	int ret;
+
+	dsi = xzalloc(sizeof(*dsi));
+
+	dsi->dev = dev;
+	dsi->plat_data = plat_data;
+
+	if (!plat_data->phy_ops->init || !plat_data->phy_ops->get_lane_mbps ||
+	    !plat_data->phy_ops->get_timing) {
+		dev_err(dev, "Phy not properly configured\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	if (!plat_data->base) {
+		iores = dev_request_mem_resource(dev, 0);
+		if (IS_ERR(iores))
+			return ERR_CAST(iores);
+		dsi->base = IOMEM(iores->start);
+	} else {
+		dsi->base = plat_data->base;
+	}
+
+	dsi->pclk = clk_get(dev, "pclk");
+	if (IS_ERR(dsi->pclk))
+		return dev_err_cast_probe(dev, dsi->pclk,
+					  "Unable to get pclk\n");
+
+	/*
+	 * Note that the reset was not defined in the initial device tree, so
+	 * we have to be prepared for it not being found.
+	 */
+	apb_rst = reset_control_get_optional(dev, "apb");
+	if (IS_ERR(apb_rst))
+		return dev_err_cast_probe(dev, apb_rst,
+					  "Unable to get reset control\n");
+
+	if (apb_rst) {
+		ret = clk_prepare_enable(dsi->pclk);
+		if (ret) {
+			dev_err(dev, "%s: Failed to enable pclk\n", __func__);
+			return ERR_PTR(ret);
+		}
+
+		reset_control_assert(apb_rst);
+		udelay(10);
+		reset_control_deassert(apb_rst);
+
+		clk_disable_unprepare(dsi->pclk);
+	}
+
+	dsi->vpl.node = dev->device_node;
+	dsi->vpl.ioctl = dw_mipi_dsi_ioctl;
+	ret = vpl_register(&dsi->vpl);
+	if (ret)
+		return ERR_PTR(ret);
+
+	dsi->dsi_host.ops = &dw_mipi_dsi_host_ops;
+	dsi->dsi_host.dev = dev;
+	ret = mipi_dsi_host_register(&dsi->dsi_host);
+	if (ret)
+		return dev_err_ptr_probe(dev, ret,
+				     "Failed to register MIPI host\n");
+
+	/* Expose Video Pattern Generator for debug purposes */
+	dev_add_param_enum(dev, "vpg", vpg_param_set, NULL,
+			   &dsi->vpg_mode, vpg_modes,
+			   ARRAY_SIZE(vpg_modes), dsi);
+
+	return dsi;
+}
+
+struct dw_mipi_dsi *dw_mipi_dsi_bind(struct device *dev,
+				     const struct dw_mipi_dsi_plat_data *plat_data)
+{
+	return dw_mipi_dsi_probe(dev, plat_data);
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_bind);
+
+struct device_node *dw_mipi_dsi_crtc_node(struct dw_mipi_dsi *dsi)
+{
+	return dsi->dsi_host.dev->of_node;
+}
+EXPORT_SYMBOL_GPL(dw_mipi_dsi_crtc_node);
+
+MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
+MODULE_AUTHOR("Philippe Cornu <philippe.cornu@st.com>");
+MODULE_AUTHOR("Yannick Fertré <yannick.fertre@st.com>");
+MODULE_DESCRIPTION("DW MIPI DSI host controller driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:dw-mipi-dsi");
diff --git a/include/video/dw_mipi_dsi.h b/include/video/dw_mipi_dsi.h
new file mode 100644
index 000000000000..9e8b279bb911
--- /dev/null
+++ b/include/video/dw_mipi_dsi.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) STMicroelectronics SA 2017
+ *
+ * Authors: Philippe Cornu <philippe.cornu@st.com>
+ *          Yannick Fertre <yannick.fertre@st.com>
+ */
+
+#ifndef __DW_MIPI_DSI__
+#define __DW_MIPI_DSI__
+
+#include <linux/types.h>
+#include <linux/compiler.h>
+
+#include <video/drm/drm_modes.h>
+
+struct drm_display_mode;
+struct dw_mipi_dsi;
+struct mipi_dsi_device;
+struct device;
+
+/**
+ * struct dw_mipi_dsi_dphy_timing - DSI host phy timings
+ * @data_hs2lp: High Speed to Low Speed Data Transition Time
+ * @data_lp2hs: Low Speed to High Speed Data Transition Time
+ * @clk_hs2lp: High Speed to Low Speed Clock Transition Time
+ * @clk_lp2hs: Low Speed to High Speed Clock Transition Time
+ */
+struct dw_mipi_dsi_dphy_timing {
+	u16 data_hs2lp;
+	u16 data_lp2hs;
+	u16 clk_hs2lp;
+	u16 clk_lp2hs;
+};
+
+struct dw_mipi_dsi_phy_ops {
+	int (*init)(void *priv_data);
+	void (*power_on)(void *priv_data);
+	void (*power_off)(void *priv_data);
+	int (*get_lane_mbps)(void *priv_data,
+			     const struct drm_display_mode *mode,
+			     unsigned long mode_flags, u32 lanes, u32 format,
+			     unsigned int *lane_mbps);
+	int (*get_timing)(void *priv_data, unsigned int lane_mbps,
+			  struct dw_mipi_dsi_dphy_timing *timing);
+	int (*get_esc_clk_rate)(void *priv_data, unsigned int *esc_clk_rate);
+};
+
+struct dw_mipi_dsi_host_ops {
+	int (*attach)(void *priv_data,
+		      struct mipi_dsi_device *dsi);
+	int (*detach)(void *priv_data,
+		      struct mipi_dsi_device *dsi);
+};
+
+struct dw_mipi_dsi_plat_data {
+	void __iomem *base;
+	unsigned int max_data_lanes;
+
+	enum drm_mode_status (*mode_valid)(void *priv_data,
+					   const struct drm_display_mode *mode,
+					   unsigned long mode_flags,
+					   u32 lanes, u32 format);
+
+	bool (*mode_fixup)(void *priv_data, const struct drm_display_mode *mode,
+			   struct drm_display_mode *adjusted_mode);
+
+	const struct dw_mipi_dsi_phy_ops *phy_ops;
+	const struct dw_mipi_dsi_host_ops *host_ops;
+
+	void *priv_data;
+};
+
+struct dw_mipi_dsi *
+dw_mipi_dsi_bind(struct device *dev,
+		 const struct dw_mipi_dsi_plat_data *plat_data);
+static inline void dw_mipi_dsi_unbind(struct dw_mipi_dsi *dsi) { }
+
+struct device_node *dw_mipi_dsi_crtc_node(struct dw_mipi_dsi *dsi);
+
+#endif /* __DW_MIPI_DSI__ */
-- 
2.39.5