From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from coyote.quickmin.net ([217.14.112.24]) by canuck.infradead.org with esmtps (Exim 4.72 #1 (Red Hat Linux)) id 1Pt0DI-0005iW-G1 for barebox@lists.infradead.org; Fri, 25 Feb 2011 16:08:17 +0000 Received: from [10.96.97.181] (tmayer.mit.telemotive.de [10.96.97.181]) by alderan.mit.telemotive.de (Postfix) with ESMTP id 2831AD7850 for ; Fri, 25 Feb 2011 17:08:11 +0100 (CET) From: Thomas Mayer MIME-Version: 1.0 References: <4D665867.4010404@telemotive.de> <20110224160440.GQ7381@pengutronix.de> <4D677315.5090600@telemotive.de> <20110225150657.GC29521@pengutronix.de> In-Reply-To: <20110225150657.GC29521@pengutronix.de> Message-ID: <4D67D3EA.9000106@telemotive.de> Date: Fri, 25 Feb 2011 17:08:10 +0100 List-Id: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: barebox-bounces@lists.infradead.org Errors-To: barebox-bounces+u.kleine-koenig=pengutronix.de@lists.infradead.org Subject: Re: Install barebox on target To: barebox@lists.infradead.org Hi Sasha, thanks, I will try that. Today I got our real hardware. It consists of the freescale cpu board, a custom baseboard with a different display. With that I was able to start barebox completely. Network works fine, but I can't access the nand memory, because barebox doesn't find it at startup. I added all possible nand drivers to barebox, but it still doesn't work. Any idea? --------------------------------------- u-boot output ----------------------------------------- U-Boot 2009.08 (Jan 13 2010 - 06:24:35) CPU: Freescale i.MX35 at 532 MHz Board: MX35 3STACK 2.0 [RST] I2C: ready DRAM: 128 MB Flash: 64 MB NAND: Manufacturer : Samsung (0xec) Device Code : 0xd7 Cell Technology : MLC Chip Size : 4 GiB Pages per Block : 128 Page Geometry : 4096+218 ECC Strength : 8 bits ECC Size : 512 B Data Setup Time : 20 ns Data Hold Time : 10 ns Address Setup Time: 25 ns GPMI Sample Delay : 6 ns tREA : Unknown tRLOH : Unknown tRHOH : Unknown Description : K9LBG08U0D Bad block table found at page 524160, version 0x01 Bad block table found at page 524032, version 0x01 2048 MiB In: serial Out: serial Err: serial PMIC@0x08:0x7 is 45d0 i.MX35 CPU board version 2.0 Net: FEC0 Hit any key to stop autoboot: 0 --------------------------------------- barebox output ------------------------------------------ barebox 2011.02.0 (Feb 25 2011 - 16:35:47) Board: Freescale MX35 3Stack No NAND device found!!! cfi_probe: cfi_flash base: 0xa0000000 size: 0x04000000 mc13892-i2c@mc13892-i2c0: PMIC ID: 0x000045d0 [Rev: 2.0a] smc911x: no smc911x found on 0xb6000000 (byte_test=0x00f000f0) imx-ipu-fb@imx-ipu-fb0: i.MX Framebuffer driver mc13892-i2c@mc13892-i2c0: revision: 0x45d0 i.MX35 PDK CPU board version 1. Malloc space: 0x86f00000 -> 0x87f00000 (size 16 MB) Stack space : 0x86ef8000 -> 0x86f00000 (size 32 kB) Open /dev/env0 No such file or directory no valid environment found on /dev/env0. Using default environment running /env/bin/init... regards Thomas Am 25.02.2011 16:06, schrieb Sascha Hauer: > On Fri, Feb 25, 2011 at 10:15:01AM +0100, Thomas Mayer wrote: > >> Hi Sascha, >> >> That's not quite correct. When you use the debug + personality board you >> can boot directly from a mmc-card which contains bootloader, kernel and >> rootfs without modifications. Only if you use the single personality >> board, you have to modify die board a little bit. >> > Ah, ok. I didn't know that. > > >> Thanks for your short introduction. I tried to run the barebox image >> with u-boot and it seems to work. But after I get the following output >> barebox stops and do nothing. >> > That's a bug in the support for multiple network devices. Please pull > the -next branch again, then it should work. > > Sascha > > > _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox