From: Marc Kleine-Budde <mkl@pengutronix.de>
To: Sascha Hauer <sha@pengutronix.de>
Cc: barebox@lists.infradead.org
Subject: Re: [PATCH 2/2] mxs: add support for mx28-evk
Date: Mon, 11 Apr 2011 10:05:25 +0200 [thread overview]
Message-ID: <4DA2B645.4000909@pengutronix.de> (raw)
In-Reply-To: <20110409132344.GB7285@pengutronix.de>
[-- Attachment #1.1: Type: text/plain, Size: 2756 bytes --]
On 04/09/2011 03:23 PM, Sascha Hauer wrote:
> On Fri, Apr 08, 2011 at 12:24:00PM +0200, Marc Kleine-Budde wrote:
>> This patch adds support for tje mx28-evk board. NAND support is still lacking,
>> so we use still the bootlets as the first stage boot loader.
>>
>> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
>> ---
>> arch/arm/Makefile | 1 +
>> arch/arm/boards/freescale-mx28-evk/Makefile | 1 +
>> arch/arm/boards/freescale-mx28-evk/config.h | 16 +
>> arch/arm/boards/freescale-mx28-evk/env/config | 67 ++++
>> arch/arm/boards/freescale-mx28-evk/mx28-evk.c | 378 ++++++++++++++++++++++
>> arch/arm/boards/freescale-mx28-evk/tx28-stk5.c | 410 ++++++++++++++++++++++++
>
> Looks like you copied a bit too much from the karo board.
doh!
>
>> +
>> +console_initcall(mx28_evk_console_init);
>> +
>> +/**
>> +@page mx28_evk KARO's MX28_EVK CPU module
>> +
>> +@section mx28_evk_cpu_card The CPU module
>> +
>> +http://www.karo-electronics.de/
>> +
>> +This CPU card is based on a Freescale i.MX28 CPU. The card is shipped with:
>> +
>> +- 128 MiB synchronous dynamic RAM (DDR2 type), 200 MHz support
>> +- 128 MiB NAND K9F1G08U0A (3.3V type)
>> +- PCA9554 GPIO expander
>> +- DS1339 RTC
>> +- LAN8710 Phy
>> +
>> +@section mx28_evk_basboards Supported baseboards
>> +
>> +Supported baseboards are:
>> +- KARO's Starterkit 5
>> +
>> +@section mx28_evk_stk5_howto How to get barebox for 'KARO's Starterkit 5'
>> +
>> +Using the default configuration:
>> +
>> +@verbatim
>> +make ARCH=arm mx28_evkstk5_defconfig
>> +@endverbatim
>> +
>> +Build the binary image:
>> +
>> +@verbatim
>> +make ARCH=arm CROSS_COMPILE=armv5compiler
>> +@endverbatim
>> +
>> +@note replace the armv5compiler with your ARM v5 cross compiler.
>> +
>> +@note To use the result, you also need the following resources from Freescale:
>> +- the 'bootlets' archive
>> +- the 'elftosb2' encryption tool
>> +- in the case you want to start @b barebox from an attached SD card the
>> + 'sdimage' tool from Freescale's 'uuc' archive.
>> +
>> +@section mx28_evk_mlayout Memory layout when barebox is running:
>> +
>> +- 0x40000000 start of SDRAM
>> +- 0x40000100 start of kernel's boot parameters
>> + - below malloc area: stack area
>> + - below barebox: malloc area
>> +- 0x47000000 start of @b barebox
>
> Please either correct this or remove it.
I'll remove it
Marc
--
Pengutronix e.K. | Marc Kleine-Budde |
Industrial Linux Solutions | Phone: +49-231-2826-924 |
Vertretung West/Dortmund | Fax: +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
[-- Attachment #1.2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 262 bytes --]
[-- Attachment #2: Type: text/plain, Size: 149 bytes --]
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2011-04-11 8:05 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-04-08 10:23 [PATCH 0/2] mxs: add mx28-evk Marc Kleine-Budde
2011-04-08 10:23 ` [PATCH 1/2] mxs: import mxs_iomux_setup_multiple_pads from kernel Marc Kleine-Budde
2011-04-09 13:26 ` Sascha Hauer
2011-04-08 10:24 ` [PATCH 2/2] mxs: add support for mx28-evk Marc Kleine-Budde
2011-04-09 13:23 ` Sascha Hauer
2011-04-11 8:05 ` Marc Kleine-Budde [this message]
2011-04-08 10:32 ` [PATCH 0/2] mxs: add mx28-evk Marc Kleine-Budde
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4DA2B645.4000909@pengutronix.de \
--to=mkl@pengutronix.de \
--cc=barebox@lists.infradead.org \
--cc=sha@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox