[PATCH v1] ARM: at91: microchip-sama5d3-eds: implement MDIO extension board detection

[PATCH v1] ARM: at91: microchip-sama5d3-eds: implement MDIO extension board detection

[Oleksij Rempel]

Detect extension boards managed over MDIO bus. For now following
extension boards are supported:
- EVB-VSC8541-EDS
- EVB-LAN8841

If supported board is detected, the board code will apply devicetree
overlay on the barebox and fixup kernel DT too.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 .../arm/boards/microchip-sama5d3-eds/Makefile |   1 +
 arch/arm/boards/microchip-sama5d3-eds/board.c | 183 ++++++++++++++++++
 arch/arm/dts/Makefile                         |   2 +
 arch/arm/dts/at91-microchip-sama5d3-eds.dts   |  27 +++
 arch/arm/dts/sama5d3_eds_rgmii_phy.dtso       |  52 +++++
 arch/arm/mach-at91/Kconfig                    |   1 +
 6 files changed, 266 insertions(+)
 create mode 100644 arch/arm/boards/microchip-sama5d3-eds/board.c
 create mode 100644 arch/arm/dts/sama5d3_eds_rgmii_phy.dtso

diff --git a/arch/arm/boards/microchip-sama5d3-eds/Makefile b/arch/arm/boards/microchip-sama5d3-eds/Makefile
index 458f520900..da63d2625f 100644
--- a/arch/arm/boards/microchip-sama5d3-eds/Makefile
+++ b/arch/arm/boards/microchip-sama5d3-eds/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
 
+obj-y += board.o
 lwl-y += lowlevel.o
diff --git a/arch/arm/boards/microchip-sama5d3-eds/board.c b/arch/arm/boards/microchip-sama5d3-eds/board.c
new file mode 100644
index 0000000000..460b5c376d
--- /dev/null
+++ b/arch/arm/boards/microchip-sama5d3-eds/board.c
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// SPDX-FileCopyrightText: 2024 Oleksij Rempel <o.rempel@pengutronix.de>
+
+#include <common.h>
+#include <environment.h>
+#include <envfs.h>
+#include <gpio.h>
+#include <init.h>
+#include <deep-probe.h>
+#include <linux/phy.h>
+
+extern char __dtbo_sama5d3_eds_rgmii_phy_start[];
+
+struct microchip_sama5d3_eds_ext_board {
+	int mdio_bus_idx;
+	int phy_addr;
+	int phy_id1;
+	int phy_id2;
+	char board_name[32];
+	const void *overlay;
+};
+
+static const struct
+microchip_sama5d3_eds_ext_board microchip_sama5d3_eds_ext_boards[] = {
+	{
+		.mdio_bus_idx = 0,
+		.phy_addr = 3,
+		.phy_id1 = 0x0007,
+		.phy_id2 = 0x0772,
+		.board_name = "EVB-VSC8541-EDS",
+		.overlay = __dtbo_sama5d3_eds_rgmii_phy_start,
+	},
+	{
+		.mdio_bus_idx = 0,
+		.phy_addr = 3,
+		.phy_id1 = 0x0022,
+		.phy_id2 = 0x1652,
+		.board_name = "EVB-LAN8841",
+		.overlay = __dtbo_sama5d3_eds_rgmii_phy_start,
+	},
+};
+
+static void microchip_sama5d3_eds_apply_overly(struct device *dev,
+			const struct microchip_sama5d3_eds_ext_board *board)
+{
+	struct device_node *overlay;
+	int ret;
+
+	overlay = of_unflatten_dtb(board->overlay, INT_MAX);
+	ret = of_overlay_apply_tree(dev->of_node, overlay);
+	if (ret)
+		dev_warn(dev, "Failed to apply overlay: %pe\n", ERR_PTR(ret));
+
+	ret = of_register_overlay(overlay);
+	if (ret)
+		dev_warn(dev, "Failed to register overlay: %pe\n",
+			 ERR_PTR(ret));
+
+}
+
+static int scan_phy_bus(struct mii_bus *bus, int *phy_addr, int *phy_id1,
+			int *phy_id2)
+{
+	int i, reg2, reg3;
+
+	for (i = 0; i < PHY_MAX_ADDR; i++) {
+		reg2 = mdiobus_read(bus, i, MII_PHYSID1);
+		if (reg2 < 0)
+			return reg2;
+
+		if (reg2 == 0xffff || reg2 == 0x0)
+			continue;
+
+		reg3 = mdiobus_read(bus, i, MII_PHYSID2);
+		if (reg3 < 0)
+			return reg3;
+
+		*phy_addr = i;
+		*phy_id1 = reg2;
+		*phy_id2 = reg3;
+
+		return 1;
+	}
+
+	return 0;
+}
+
+static int microchip_sama5d3_eds_scan_mdio_bus(struct device *dev,
+					       int mdio_bus_idx)
+{
+	struct device_node *eth_node, *mdio_node;
+	char eth_alias[] = "ethernetX";
+	char mdio_alias[] = "mdioX";
+	struct mii_bus *mdio_bus;
+	int phy_addr, phy_id1, phy_id2;
+	int ret;
+
+	snprintf(eth_alias, sizeof(eth_alias), "ethernet%d", mdio_bus_idx);
+	snprintf(mdio_alias, sizeof(mdio_alias), "mdio%d", mdio_bus_idx);
+
+	eth_node = of_find_node_by_alias(NULL, eth_alias);
+	if (!eth_node)
+		return -ENODEV;
+
+	of_device_ensure_probed(eth_node);
+
+	mdio_node = of_find_node_by_alias(NULL, mdio_alias);
+	if (!mdio_node)
+		return -ENODEV;
+
+	of_device_ensure_probed(mdio_node);
+
+	mdio_bus = of_mdio_find_bus(mdio_node);
+	if (!mdio_bus)
+		return -ENODEV;
+
+	ret = scan_phy_bus(mdio_bus, &phy_addr, &phy_id1, &phy_id2);
+	if (ret < 0) {
+		dev_warn(dev, "Failed to scan mdio%d bus: %d\n", mdio_bus_idx,
+			 ret);
+		return ret;
+	} else if (!ret) {
+		/* No PHY found */
+		return 0;
+	}
+
+	dev_info(dev, "Found PHY at bus %d, address %d: %04x:%04x\n",
+		 mdio_bus_idx, phy_addr, phy_id1, phy_id2);
+
+	for (int i = 0; i < ARRAY_SIZE(microchip_sama5d3_eds_ext_boards); i++) {
+		const struct microchip_sama5d3_eds_ext_board *board =
+			&microchip_sama5d3_eds_ext_boards[i];
+
+		if (board->mdio_bus_idx != mdio_bus_idx)
+			continue;
+
+		if (board->phy_addr == phy_addr &&
+		    board->phy_id1 == phy_id1 &&
+		    board->phy_id2 == phy_id2) {
+			char base_board_name[100] = "Microchip SAMA5D3 EDS";
+
+			dev_info(dev, "Found extension board: %s\n",
+				 board->board_name);
+
+			snprintf(base_board_name, sizeof(base_board_name),
+				 "%s with %s",
+				 base_board_name, board->board_name);
+			barebox_set_model(base_board_name);
+
+			if (board->overlay)
+				microchip_sama5d3_eds_apply_overly(dev, board);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int microchip_sama5d3_eds_probe(struct device *dev)
+{
+	int ret, i;
+
+	for (i = 0; i < 2; i++) {
+		ret = microchip_sama5d3_eds_scan_mdio_bus(dev, i);
+		if (ret)
+			dev_warn(dev, "Failed to scan mdio%d bus\n", i);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id microchip_sama5d3_eds_of_match[] = {
+	{ .compatible = "microchip,sama5d3-eds"},
+	{ /* sentinel */ },
+};
+BAREBOX_DEEP_PROBE_ENABLE(microchip_sama5d3_eds_of_match);
+
+static struct driver microchip_sama5d3_eds_board_driver = {
+	.name = "board-microchip-sama5d3-eds",
+	.probe = microchip_sama5d3_eds_probe,
+	.of_compatible = DRV_OF_COMPAT(microchip_sama5d3_eds_of_match),
+};
+device_platform_driver(microchip_sama5d3_eds_board_driver);
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 68585e1e4b..627f6e7afb 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -230,6 +230,8 @@ lwl-$(CONFIG_MACH_VARISCITE_DT8MCUSTOMBOARD_IMX8MP) += imx8mp-var-dart-dt8mcusto
 lwl-$(CONFIG_MACH_TQMA93XX) += imx93-tqma9352-mba93xxca.dtb.o \
 			       imx93-tqma9352-mba93xxla.dtb.o
 
+obj-$(CONFIG_MACH_MICROCHIP_SAMA5D3_EDS) += sama5d3_eds_rgmii_phy.dtbo.o
+
 obj-$(CONFIG_MACH_WOLFVISION_PF5) += rk3568-wolfvision-pf5-io-expander.dtbo.o
 
 clean-files := *.dtb *.dtb.S .*.dtc .*.pre .*.dts *.dtb.z
diff --git a/arch/arm/dts/at91-microchip-sama5d3-eds.dts b/arch/arm/dts/at91-microchip-sama5d3-eds.dts
index d35c8c3c6e..30f86b144d 100644
--- a/arch/arm/dts/at91-microchip-sama5d3-eds.dts
+++ b/arch/arm/dts/at91-microchip-sama5d3-eds.dts
@@ -11,4 +11,31 @@ environment {
 			file-path = "barebox.env";
 		};
 	};
+
+	aliases {
+		ethernet0 = &macb0;
+		ethernet1 = &macb1;
+		mdio0 = &mdio0;
+		mdio1 = &mdio1;
+	};
+};
+
+&macb0 {
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio0: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&macb1 {
+	phy-mode = "rmii";
+	status = "okay";
+
+	mdio1: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
 };
diff --git a/arch/arm/dts/sama5d3_eds_rgmii_phy.dtso b/arch/arm/dts/sama5d3_eds_rgmii_phy.dtso
new file mode 100644
index 0000000000..5d7e1ee54c
--- /dev/null
+++ b/arch/arm/dts/sama5d3_eds_rgmii_phy.dtso
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for SAMA5D3 EDS board
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Jerry Ray <jerry.ray@microchip.com>
+ *
+ * Supported extension boards:
+ * - EVB-LAN8841 - https://www.microchip.com/en-us/development-tool/EV19G28A
+ *   Note: Depopulate R43 (remove RXER signal) to allow this board to
+ *         function properly with the SAMA5D3-EDS.
+ * - EVB-VSC8541-EDS - https://www.microchip.com/en-us/development-tool/EV35M06A
+ */
+/dts-v1/;
+/plugin/;
+
+#include "dt-bindings/gpio/gpio.h"
+#include "dt-bindings/interrupt-controller/irq.h"
+#include "dt-bindings/pinctrl/at91.h"
+
+&macb0 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rgmii_phy: ethernet-phy@3 {
+			reg = <0x3>;
+			pinctrl-0 = <&pinctrl_rgmii_rstn>;
+			pinctrl-1 = <&pinctrl_spi_irqn>;
+			interrupt-parent = <&pioB>;
+			interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+			resetb-gpios = <&pioD 18 GPIO_ACTIVE_LOW>;
+			/* LAN8841 - 1us */
+			/* VSC8541 - 100ns */
+			/* take one 1ms to be safe */
+			reset-assert-us = <1000>;
+			/* LAN8841 - 10ms? */
+			/* VSC8541- 15ms */
+			reset-deassert-us = <15000>;
+			status = "okay";
+		};
+	};
+};
+
+&usart0 {
+	status = "disabled";    /* Conflicts with using pioD 18 as GPIO */
+};
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index afcea257c3..3cf40463be 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -612,6 +612,7 @@ config MACH_MICROCHIP_SAMA5D3_EDS
 	select OFDEVICE
 	select MCI_ATMEL_PBL
 	select COMMON_CLK_OF_PROVIDER
+	select OF_OVERLAY
 	help
 	  Select this if you are using Microchip's SAMA5D3 Ethernet Development
 	  System.
-- 
2.39.2

Re: [PATCH v1] ARM: at91: microchip-sama5d3-eds: implement MDIO extension board detection

[linux]

Please ingore it, i'll send new version with SPI and MDIO detection.

Am 21.06.24 um 14:25 schrieb Oleksij Rempel:
> Detect extension boards managed over MDIO bus. For now following
> extension boards are supported:
> - EVB-VSC8541-EDS
> - EVB-LAN8841
>
> If supported board is detected, the board code will apply devicetree
> overlay on the barebox and fixup kernel DT too.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>   .../arm/boards/microchip-sama5d3-eds/Makefile |   1 +
>   arch/arm/boards/microchip-sama5d3-eds/board.c | 183 ++++++++++++++++++
>   arch/arm/dts/Makefile                         |   2 +
>   arch/arm/dts/at91-microchip-sama5d3-eds.dts   |  27 +++
>   arch/arm/dts/sama5d3_eds_rgmii_phy.dtso       |  52 +++++
>   arch/arm/mach-at91/Kconfig                    |   1 +
>   6 files changed, 266 insertions(+)
>   create mode 100644 arch/arm/boards/microchip-sama5d3-eds/board.c
>   create mode 100644 arch/arm/dts/sama5d3_eds_rgmii_phy.dtso
>
> diff --git a/arch/arm/boards/microchip-sama5d3-eds/Makefile b/arch/arm/boards/microchip-sama5d3-eds/Makefile
> index 458f520900..da63d2625f 100644
> --- a/arch/arm/boards/microchip-sama5d3-eds/Makefile
> +++ b/arch/arm/boards/microchip-sama5d3-eds/Makefile
> @@ -1,3 +1,4 @@
>   # SPDX-License-Identifier: GPL-2.0-only
>
> +obj-y += board.o
>   lwl-y += lowlevel.o
> diff --git a/arch/arm/boards/microchip-sama5d3-eds/board.c b/arch/arm/boards/microchip-sama5d3-eds/board.c
> new file mode 100644
> index 0000000000..460b5c376d
> --- /dev/null
> +++ b/arch/arm/boards/microchip-sama5d3-eds/board.c
> @@ -0,0 +1,183 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// SPDX-FileCopyrightText: 2024 Oleksij Rempel <o.rempel@pengutronix.de>
> +
> +#include <common.h>
> +#include <environment.h>
> +#include <envfs.h>
> +#include <gpio.h>
> +#include <init.h>
> +#include <deep-probe.h>
> +#include <linux/phy.h>
> +
> +extern char __dtbo_sama5d3_eds_rgmii_phy_start[];
> +
> +struct microchip_sama5d3_eds_ext_board {
> +	int mdio_bus_idx;
> +	int phy_addr;
> +	int phy_id1;
> +	int phy_id2;
> +	char board_name[32];
> +	const void *overlay;
> +};
> +
> +static const struct
> +microchip_sama5d3_eds_ext_board microchip_sama5d3_eds_ext_boards[] = {
> +	{
> +		.mdio_bus_idx = 0,
> +		.phy_addr = 3,
> +		.phy_id1 = 0x0007,
> +		.phy_id2 = 0x0772,
> +		.board_name = "EVB-VSC8541-EDS",
> +		.overlay = __dtbo_sama5d3_eds_rgmii_phy_start,
> +	},
> +	{
> +		.mdio_bus_idx = 0,
> +		.phy_addr = 3,
> +		.phy_id1 = 0x0022,
> +		.phy_id2 = 0x1652,
> +		.board_name = "EVB-LAN8841",
> +		.overlay = __dtbo_sama5d3_eds_rgmii_phy_start,
> +	},
> +};
> +
> +static void microchip_sama5d3_eds_apply_overly(struct device *dev,
> +			const struct microchip_sama5d3_eds_ext_board *board)
> +{
> +	struct device_node *overlay;
> +	int ret;
> +
> +	overlay = of_unflatten_dtb(board->overlay, INT_MAX);
> +	ret = of_overlay_apply_tree(dev->of_node, overlay);
> +	if (ret)
> +		dev_warn(dev, "Failed to apply overlay: %pe\n", ERR_PTR(ret));
> +
> +	ret = of_register_overlay(overlay);
> +	if (ret)
> +		dev_warn(dev, "Failed to register overlay: %pe\n",
> +			 ERR_PTR(ret));
> +
> +}
> +
> +static int scan_phy_bus(struct mii_bus *bus, int *phy_addr, int *phy_id1,
> +			int *phy_id2)
> +{
> +	int i, reg2, reg3;
> +
> +	for (i = 0; i < PHY_MAX_ADDR; i++) {
> +		reg2 = mdiobus_read(bus, i, MII_PHYSID1);
> +		if (reg2 < 0)
> +			return reg2;
> +
> +		if (reg2 == 0xffff || reg2 == 0x0)
> +			continue;
> +
> +		reg3 = mdiobus_read(bus, i, MII_PHYSID2);
> +		if (reg3 < 0)
> +			return reg3;
> +
> +		*phy_addr = i;
> +		*phy_id1 = reg2;
> +		*phy_id2 = reg3;
> +
> +		return 1;
> +	}
> +
> +	return 0;
> +}
> +
> +static int microchip_sama5d3_eds_scan_mdio_bus(struct device *dev,
> +					       int mdio_bus_idx)
> +{
> +	struct device_node *eth_node, *mdio_node;
> +	char eth_alias[] = "ethernetX";
> +	char mdio_alias[] = "mdioX";
> +	struct mii_bus *mdio_bus;
> +	int phy_addr, phy_id1, phy_id2;
> +	int ret;
> +
> +	snprintf(eth_alias, sizeof(eth_alias), "ethernet%d", mdio_bus_idx);
> +	snprintf(mdio_alias, sizeof(mdio_alias), "mdio%d", mdio_bus_idx);
> +
> +	eth_node = of_find_node_by_alias(NULL, eth_alias);
> +	if (!eth_node)
> +		return -ENODEV;
> +
> +	of_device_ensure_probed(eth_node);
> +
> +	mdio_node = of_find_node_by_alias(NULL, mdio_alias);
> +	if (!mdio_node)
> +		return -ENODEV;
> +
> +	of_device_ensure_probed(mdio_node);
> +
> +	mdio_bus = of_mdio_find_bus(mdio_node);
> +	if (!mdio_bus)
> +		return -ENODEV;
> +
> +	ret = scan_phy_bus(mdio_bus, &phy_addr, &phy_id1, &phy_id2);
> +	if (ret < 0) {
> +		dev_warn(dev, "Failed to scan mdio%d bus: %d\n", mdio_bus_idx,
> +			 ret);
> +		return ret;
> +	} else if (!ret) {
> +		/* No PHY found */
> +		return 0;
> +	}
> +
> +	dev_info(dev, "Found PHY at bus %d, address %d: %04x:%04x\n",
> +		 mdio_bus_idx, phy_addr, phy_id1, phy_id2);
> +
> +	for (int i = 0; i < ARRAY_SIZE(microchip_sama5d3_eds_ext_boards); i++) {
> +		const struct microchip_sama5d3_eds_ext_board *board =
> +			&microchip_sama5d3_eds_ext_boards[i];
> +
> +		if (board->mdio_bus_idx != mdio_bus_idx)
> +			continue;
> +
> +		if (board->phy_addr == phy_addr &&
> +		    board->phy_id1 == phy_id1 &&
> +		    board->phy_id2 == phy_id2) {
> +			char base_board_name[100] = "Microchip SAMA5D3 EDS";
> +
> +			dev_info(dev, "Found extension board: %s\n",
> +				 board->board_name);
> +
> +			snprintf(base_board_name, sizeof(base_board_name),
> +				 "%s with %s",
> +				 base_board_name, board->board_name);
> +			barebox_set_model(base_board_name);
> +
> +			if (board->overlay)
> +				microchip_sama5d3_eds_apply_overly(dev, board);
> +			break;
> +		}
> +	}
> +
> +	return 0;
> +}
> +
> +static int microchip_sama5d3_eds_probe(struct device *dev)
> +{
> +	int ret, i;
> +
> +	for (i = 0; i < 2; i++) {
> +		ret = microchip_sama5d3_eds_scan_mdio_bus(dev, i);
> +		if (ret)
> +			dev_warn(dev, "Failed to scan mdio%d bus\n", i);
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id microchip_sama5d3_eds_of_match[] = {
> +	{ .compatible = "microchip,sama5d3-eds"},
> +	{ /* sentinel */ },
> +};
> +BAREBOX_DEEP_PROBE_ENABLE(microchip_sama5d3_eds_of_match);
> +
> +static struct driver microchip_sama5d3_eds_board_driver = {
> +	.name = "board-microchip-sama5d3-eds",
> +	.probe = microchip_sama5d3_eds_probe,
> +	.of_compatible = DRV_OF_COMPAT(microchip_sama5d3_eds_of_match),
> +};
> +device_platform_driver(microchip_sama5d3_eds_board_driver);
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 68585e1e4b..627f6e7afb 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -230,6 +230,8 @@ lwl-$(CONFIG_MACH_VARISCITE_DT8MCUSTOMBOARD_IMX8MP) += imx8mp-var-dart-dt8mcusto
>   lwl-$(CONFIG_MACH_TQMA93XX) += imx93-tqma9352-mba93xxca.dtb.o \
>   			       imx93-tqma9352-mba93xxla.dtb.o
>
> +obj-$(CONFIG_MACH_MICROCHIP_SAMA5D3_EDS) += sama5d3_eds_rgmii_phy.dtbo.o
> +
>   obj-$(CONFIG_MACH_WOLFVISION_PF5) += rk3568-wolfvision-pf5-io-expander.dtbo.o
>
>   clean-files := *.dtb *.dtb.S .*.dtc .*.pre .*.dts *.dtb.z
> diff --git a/arch/arm/dts/at91-microchip-sama5d3-eds.dts b/arch/arm/dts/at91-microchip-sama5d3-eds.dts
> index d35c8c3c6e..30f86b144d 100644
> --- a/arch/arm/dts/at91-microchip-sama5d3-eds.dts
> +++ b/arch/arm/dts/at91-microchip-sama5d3-eds.dts
> @@ -11,4 +11,31 @@ environment {
>   			file-path = "barebox.env";
>   		};
>   	};
> +
> +	aliases {
> +		ethernet0 = &macb0;
> +		ethernet1 = &macb1;
> +		mdio0 = &mdio0;
> +		mdio1 = &mdio1;
> +	};
> +};
> +
> +&macb0 {
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	mdio0: mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +};
> +
> +&macb1 {
> +	phy-mode = "rmii";
> +	status = "okay";
> +
> +	mdio1: mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
>   };
> diff --git a/arch/arm/dts/sama5d3_eds_rgmii_phy.dtso b/arch/arm/dts/sama5d3_eds_rgmii_phy.dtso
> new file mode 100644
> index 0000000000..5d7e1ee54c
> --- /dev/null
> +++ b/arch/arm/dts/sama5d3_eds_rgmii_phy.dtso
> @@ -0,0 +1,52 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for SAMA5D3 EDS board
> + *
> + * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
> + *
> + * Author: Jerry Ray <jerry.ray@microchip.com>
> + *
> + * Supported extension boards:
> + * - EVB-LAN8841 - https://www.microchip.com/en-us/development-tool/EV19G28A
> + *   Note: Depopulate R43 (remove RXER signal) to allow this board to
> + *         function properly with the SAMA5D3-EDS.
> + * - EVB-VSC8541-EDS - https://www.microchip.com/en-us/development-tool/EV35M06A
> + */
> +/dts-v1/;
> +/plugin/;
> +
> +#include "dt-bindings/gpio/gpio.h"
> +#include "dt-bindings/interrupt-controller/irq.h"
> +#include "dt-bindings/pinctrl/at91.h"
> +
> +&macb0 {
> +	phy-mode = "rgmii-id";
> +	phy-handle = <&rgmii_phy>;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		rgmii_phy: ethernet-phy@3 {
> +			reg = <0x3>;
> +			pinctrl-0 = <&pinctrl_rgmii_rstn>;
> +			pinctrl-1 = <&pinctrl_spi_irqn>;
> +			interrupt-parent = <&pioB>;
> +			interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
> +			resetb-gpios = <&pioD 18 GPIO_ACTIVE_LOW>;
> +			/* LAN8841 - 1us */
> +			/* VSC8541 - 100ns */
> +			/* take one 1ms to be safe */
> +			reset-assert-us = <1000>;
> +			/* LAN8841 - 10ms? */
> +			/* VSC8541- 15ms */
> +			reset-deassert-us = <15000>;
> +			status = "okay";
> +		};
> +	};
> +};
> +
> +&usart0 {
> +	status = "disabled";    /* Conflicts with using pioD 18 as GPIO */
> +};
> diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
> index afcea257c3..3cf40463be 100644
> --- a/arch/arm/mach-at91/Kconfig
> +++ b/arch/arm/mach-at91/Kconfig
> @@ -612,6 +612,7 @@ config MACH_MICROCHIP_SAMA5D3_EDS
>   	select OFDEVICE
>   	select MCI_ATMEL_PBL
>   	select COMMON_CLK_OF_PROVIDER
> +	select OF_OVERLAY
>   	help
>   	  Select this if you are using Microchip's SAMA5D3 Ethernet Development
>   	  System.