* Re: Barebox State Framework
2017-03-17 7:39 ` Sascha Hauer
@ 2017-03-20 4:39 ` Çağlar Kilimci
2017-03-20 7:01 ` Sascha Hauer
0 siblings, 1 reply; 4+ messages in thread
From: Çağlar Kilimci @ 2017-03-20 4:39 UTC (permalink / raw)
To: Sascha Hauer; +Cc: barebox
Hi,
2017-03-17 10:39 GMT+03:00 Sascha Hauer <s.hauer@pengutronix.de>:
> Hi,
>
> On Thu, Mar 16, 2017 at 04:55:07PM +0300, Çağlar Kilimci wrote:
>> Hello all,
>>
>> As my general purpose of updating a system with RUAC [1], I need to
>> use Barebox State Framework but I could not run it properly. I have
>> appended Barebox config these:
>>
>> CONFIG_STATE=y
>> CONFIG_STATE_CRYPTO=y
>> CONFIG_CMD_SHA1SUM=y
>> CONFIG_CMD_SHA224SUM=y
>> CONFIG_CMD_SHA256SUM=y
>> CONFIG_CMD_SHA384SUM=y
>> CONFIG_CMD_SHA512SUM=y
>> CONFIG_CMD_STATE=y
>> CONFIG_STATE_DRV=y
>> CONFIG_DIGEST_HMAC=y
>> CONFIG_DIGEST_SHA1_GENERIC=y
>> CONFIG_DIGEST_HMAC_GENERIC=y
>> CONFIG_CRYPTO_KEYSTORE=y
>> CONFIG_BOOTCHOOSER=y
>> CONFIG_CMD_BOOTCHOOSER=y
>>
>> And also, I include below into my dts:
>> state: state@0 {
>> magic = <0x27031977>;
>> compatible = "barebox,state";
>> backend-type = "raw";
>> backend = "partname:state";
>
> This looks wrong. This should be a phandle pointing to the partition you
> want to use.
Should it be like:
backend = "mmc0:0";
Do you know or recommend any source to read about State Framework details?
>
> Otherwise it looks ok. Could you provide a boot log?
Here, it is:
barebox 2016.07.0 #1 Tue Mar 7 17:47:51 +03 2017
Board: Phytec phyCORE AM335x
omap-hsmmc 48060000.mmc: registered as 48060000.mmc
booting from MMC
mmc0: detected SD card version 2.0
mmc0: registered mmc0
barebox 2016.07.0 #1 Thu Mar 16 16:20:57 +03 2017
Board: Phytec phyCORE AM335x
cpsw 4a100000.ethernet: detected phy mask 0x3
mdio_bus: miibus0: probed
eth0: got preset MAC address: 88:c2:55:4d:f2:eb
am335x-phy-driver 47401b00.usb-phy: am_usbphy 87ff0bcc enabled
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk
split, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
i2c-omap 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
omap-hsmmc 48060000.mmc: registered as 48060000.mmc
mmc0: detected SD card version 2.0
mmc0: registered mmc0
omap_wdt 44e35000.wdt: OMAP Watchdog Timer Rev 0x01
nand: ONFI flash detected
nand: NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron
MT29F1G08ABADAH4), 128MiB, page size: 2048, OOB size: 64
netconsole: registered as netconsole-1
malloc space: 0x87f7efa0 -> 0x8fefdf3f (size 127.5 MiB)
environment load /boot/barebox.env: No such file or directory
Maybe you have to create the partition.
running /env/bin/init...
Hit m for menu or any other key to stop autoboot: 1
blspec: blspec_scan_directory: mmc loader/entries
Loading ARM Linux zImage '/boot/linuximage'
Loading devicetree from '/boot/oftree'
commandline: consoleblank=0 console=ttyO0,115200n8
root=/dev/mmcblk0p2 rootflags=data=journal
video=HDMI-A-1:1024x768-32@60 rootwait ro fsck.repair=yes
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.4.19 (user@2cd11a5230c0) (gcc version
6.3.0 (GCC) ) #1 Thu Mar 16 16:22:39 +03 2017
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] Machine model: Phytec AM335x phyBOARD-WEGA
[ 0.000000] cma: Reserved 16 MiB at 0x8f000000
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] AM335X ES2.1 (sgx neon )
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 64960
[ 0.000000] Kernel command line: consoleblank=0
console=ttyO0,115200n8 root=/dev/mmcblk0p2 rootflags=data=journal
video=HDMI-A-1:1024x768-32@60 rootwait ro fsck.repair=yes
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 233856K/262144K available (6231K kernel code,
265K rwdata, 2044K rodata, 284K init, 253K bss, 11904K reserved,
16384K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc081cf7c (8276 kB)
[ 0.000000] .init : 0xc081d000 - 0xc0864000 ( 284 kB)
[ 0.000000] .data : 0xc0864000 - 0xc08a6620 ( 266 kB)
[ 0.000000] .bss : 0xc08a9000 - 0xc08e8498 ( 254 kB)
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with
128 interrupts
[ 0.000000] OMAP clockevent source: timer2 at 25000000 Hz
[ 0.000015] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps
every 85899345900ns
[ 0.000040] clocksource: timer1: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000054] OMAP clocksource: timer1 at 25000000 Hz
[ 0.000695] clocksource_probe: no matching clocksources found
[ 0.000993] Console: colour dummy device 80x30
[ 0.001029] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032)
[ 0.058710] pid_max: default: 32768 minimum: 301
[ 0.058857] Security Framework initialized
[ 0.058921] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.058937] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.059820] Initializing cgroup subsys io
[ 0.059854] Initializing cgroup subsys memory
[ 0.059903] Initializing cgroup subsys devices
[ 0.059929] Initializing cgroup subsys freezer
[ 0.059947] Initializing cgroup subsys perf_event
[ 0.059982] CPU: Testing write buffer coherency: ok
[ 0.060419] Setting up static identity map for 0x80008200 - 0x80008270
[ 0.063305] devtmpfs: initialized
[ 0.082447] VFP support v0.3: implementor 41 architecture 3 part 30
variant c rev 3
[ 0.100976] omap_hwmod: debugss: _wait_target_disable failed
[ 0.159345] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.161191] pinctrl core: initialized pinctrl subsystem
[ 0.162539] NET: Registered protocol family 16
[ 0.165098] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.166002] cpuidle: using governor ladder
[ 0.166025] cpuidle: using governor menu
[ 0.171930] OMAP GPIO hardware version 0.1
[ 0.182051] omap-gpmc 50000000.gpmc: could not find pctldev for
node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_nandflash,
deferring probe
[ 0.185985] No ATAGs?
[ 0.186016] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.207246] edma 49000000.edma: TI EDMA DMA engine driver
[ 0.212266] SCSI subsystem initialized
[ 0.213001] usbcore: registered new interface driver usbfs
[ 0.213096] usbcore: registered new interface driver hub
[ 0.213201] usbcore: registered new device driver usb
[ 0.213703] omap_i2c 44e0b000.i2c: could not find pctldev for node
/ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0, deferring
probe
[ 0.213893] Linux video capture interface: v2.00
[ 0.213962] pps_core: LinuxPPS API ver. 1 registered
[ 0.213972] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <giometti@linux.it>
[ 0.214009] PTP clock support registered
[ 0.215580] clocksource: Switched to clocksource timer1
[ 0.229315] NET: Registered protocol family 2
[ 0.230270] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.230315] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.230352] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.230440] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.230466] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.230655] NET: Registered protocol family 1
[ 0.231131] RPC: Registered named UNIX socket transport module.
[ 0.231147] RPC: Registered udp transport module.
[ 0.231156] RPC: Registered tcp transport module.
[ 0.231164] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.232522] hw perfevents: enabled with armv7_cortex_a8 PMU driver,
5 counters available
[ 0.234987] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.235086] audit: initializing netlink subsys (disabled)
[ 0.235157] audit: type=2000 audit(0.210:1): initialized
[ 0.236391] VFS: Disk quotas dquot_6.6.0
[ 0.236474] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.237248] NFS: Registering the id_resolver key type
[ 0.237324] Key type id_resolver registered
[ 0.237336] Key type id_legacy registered
[ 0.237415] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.243794] NET: Registered protocol family 38
[ 0.243870] io scheduler noop registered
[ 0.243888] io scheduler deadline registered
[ 0.243927] io scheduler cfq registered (default)
[ 0.245372] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[ 0.247944] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.250478] omap_uart 44e09000.serial: no wakeirq for uart0
[ 0.250700] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 158,
base_baud = 3000000) is a OMAP UART0
[ 0.880824] console [ttyO0] enabled
[ 0.885140] omap_uart 48022000.serial: no wakeirq for uart1
[ 0.891210] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 159,
base_baud = 3000000) is a OMAP UART1
[ 0.902381] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20
[ 0.909546] [drm] Initialized drm 1.1.0 20060810
[ 0.929816] brd: module loaded
[ 0.941014] loop: module loaded
[ 0.949293] CAN device driver interface
[ 0.954663] c_can_platform 481d0000.can: c_can_platform device
registered (regs=fa1d0000, irq=163)
[ 1.025661] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[ 1.032084] davinci_mdio 4a101000.mdio: detected phy mask fffffffc
[ 1.040201] libphy: 4a101000.mdio: probed
[ 1.044435] davinci_mdio 4a101000.mdio: phy[0]: device
4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[ 1.054109] davinci_mdio 4a101000.mdio: phy[1]: device
4a101000.mdio:01, driver SMSC LAN8710/LAN8720
[ 1.064741] cpsw 4a100000.ethernet: Detected MACID = 88:c2:55:4d:f2:eb
[ 1.072794] cpsw 4a100000.ethernet: cpsw: Detected MACID = 88:c2:55:4d:f2:ed
[ 1.081549] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.088477] ehci-platform: EHCI generic platform driver
[ 1.094231] ehci-omap: OMAP-EHCI Host Controller driver
[ 1.099905] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.106568] usbcore: registered new interface driver usb-storage
[ 1.115128] 47401300.usb-phy supply vcc not found, using dummy regulator
[ 1.124788] musb-hdrc musb-hdrc.0.auto: Failed to request rx1.
[ 1.131030] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed
with status -517
[ 1.140443] 47401b00.usb-phy supply vcc not found, using dummy regulator
[ 1.149912] musb-hdrc musb-hdrc.1.auto: Failed to request rx1.
[ 1.156137] musb-hdrc musb-hdrc.1.auto: musb_init_controller failed
with status -517
[ 1.173208] mousedev: PS/2 mouse device common for all mice
[ 1.180718] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc1
[ 1.188621] i2c /dev entries driver
[ 1.193476] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 1.201974] omap_hsmmc 48060000.mmc: Got CD GPIO
[ 1.248663] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.255389] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 1.265412] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 1.273735] oprofile: using arm/armv7
[ 1.281314] Initializing XFRM netlink socket
[ 1.286020] NET: Registered protocol family 10
[ 1.292142] sit: IPv6 over IPv4 tunneling driver
[ 1.298105] NET: Registered protocol family 17
[ 1.302791] NET: Registered protocol family 15
[ 1.307568] can: controller area network core (rev 20120528 abi 9)
[ 1.314178] NET: Registered protocol family 29
[ 1.318929] can: raw protocol (rev 20120528)
[ 1.323426] can: broadcast manager protocol (rev 20120528 t)
[ 1.329409] can: netlink gateway (rev 20130117) max_hops=1
[ 1.335304] 8021q: 802.1Q VLAN Support v1.8
[ 1.339842] Key type dns_resolver registered
[ 1.344574] omap_voltage_late_init: Voltage driver support not added
[ 1.352543] ThumbEE CPU extension supported.
[ 1.359323] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[ 1.364806] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[ 1.372996] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1
[ 1.379795] nand: Micron MT29F1G08ABADAH4
[ 1.384016] nand: 128 MiB, SLC, erase size: 128 KiB, page size:
2048, OOB size: 64
[ 1.392033] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[ 1.397793] 8 ofpart partitions found on MTD device 8000000.nand
[ 1.404134] Creating 8 MTD partitions on "8000000.nand":
[ 1.409750] mmc0: host does not support reading read-only switch,
assuming write-enable
[ 1.418232] 0x000000000000-0x000000020000 : "xload"
[ 1.423914] mmc0: new high speed SDHC card at address aaaa
[ 1.430927] 0x000000020000-0x000000040000 : "xload_backup1"
[ 1.437473] mmcblk0: mmc0:aaaa SL32G 29.7 GiB
[ 1.444299] 0x000000040000-0x000000060000 : "xload_backup2"
[ 1.450389] mmcblk0: p1 p2
[ 1.455948] 0x000000060000-0x000000080000 : "xload_backup3"
[ 1.463295] 0x000000080000-0x000000100000 : "barebox"
[ 1.470229] 0x000000100000-0x000000180000 : "barebox_backup"
[ 1.477746] 0x000000180000-0x0000001c0000 : "bareboxenv"
[ 1.484694] 0x0000001c0000-0x000008000000 : "root"
[ 1.555735] tps65910 0-002d: No interrupt support, no core IRQ
[ 1.586529] tps65910-rtc tps65910-rtc: IRQ is not free.
[ 1.592053] tps65910-rtc: probe of tps65910-rtc failed with error -22
[ 1.599353] at24 0-0052: 4096 byte 24c32 EEPROM, writable, 32 bytes/write
[ 1.607642] rtc-m41t80 0-0068: rtc core: registered rv4162 as rtc0
[ 1.616512] dummy 0-0034: Error -121 writing to cec:0xff
[ 1.622171] tda998x 0-0070: set_page 000a err -121
[ 1.685668] tda998x 0-0070: set_page 000a err -121
[ 1.745656] tda998x 0-0070: set_page 0001 err -121
[ 1.750751] tda998x 0-0070: set_page 0001 err -121
[ 1.755865] tda998x 0-0070: set_page 0200 err -121
[ 1.760964] tda998x 0-0070: set_page 0201 err -121
[ 1.766076] tda998x 0-0070: set_page 0202 err -121
[ 1.771173] tda998x 0-0070: set_page 0203 err -121
[ 1.776286] tda998x 0-0070: set_page 0204 err -121
[ 1.781381] tda998x 0-0070: set_page 0205 err -121
[ 1.786493] tda998x 0-0070: set_page 020e err -121
[ 1.791588] tda998x 0-0070: set_page 0211 err -121
[ 1.796701] tda998x 0-0070: set_page 0207 err -121
[ 1.801796] tda998x 0-0070: set_page 0208 err -121
[ 1.806909] tda998x 0-0070: set_page 0209 err -121
[ 1.812003] tda998x 0-0070: set_page 020a err -121
[ 1.817114] tda998x 0-0070: set_page 0206 err -121
[ 1.822209] tda998x 0-0070: set_page 0027 err -121
[ 1.827322] tda998x 0-0070: set_page 0000 err -121
[ 1.832416] tda998x 0-0070: set_page 0002 err -121
[ 1.837621] tilcdc 4830e000.lcdc: failed to bind 0-0070 (ops tda998x_ops): -6
[ 1.845748] tilcdc 4830e000.lcdc: master bind failed: -6
[ 1.851463] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[ 1.865697] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver
[ 1.871777] musb-hdrc musb-hdrc.0.auto: new USB bus registered,
assigned bus number 1
[ 1.880265] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.887435] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.895031] usb usb1: Product: MUSB HDRC host driver
[ 1.900266] usb usb1: Manufacturer: Linux 4.4.19 musb-hcd
[ 1.905956] usb usb1: SerialNumber: musb-hdrc.0.auto
[ 1.912146] hub 1-0:1.0: USB hub found
[ 1.916172] hub 1-0:1.0: 1 port detected
[ 1.929442] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 1.935516] musb-hdrc musb-hdrc.1.auto: new USB bus registered,
assigned bus number 2
[ 1.943979] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.951146] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.958755] usb usb2: Product: MUSB HDRC host driver
[ 1.963976] usb usb2: Manufacturer: Linux 4.4.19 musb-hcd
[ 1.969665] usb usb2: SerialNumber: musb-hdrc.1.auto
[ 1.975809] hub 2-0:1.0: USB hub found
[ 1.979793] hub 2-0:1.0: 1 port detected
[ 1.984704] vdd_mpu: supplied by vcc5v
[ 1.990998] input: user_buttons as
/devices/platform/user_buttons/input/input0
[ 1.999688] rtc-m41t80 0-0068: setting system clock to 2017-03-17
13:21:34 UTC (1489756894)
[ 2.009125] lcd_3v3: disabling
[ 2.019520] EXT4-fs: Warning: mounting with data=journal disables
delayed allocation and O_DIRECT support!
[ 2.029704] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to
feature incompatibilities
[ 2.053774] EXT4-fs (mmcblk0p2): mounted filesystem with journalled
data mode. Opts: data=journal
[ 2.063221] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 2.081914] devtmpfs: mounted
[ 2.085413] Freeing unused kernel memory: 284K (c081d000 - c0864000)
[ 2.446887] random: systemd: uninitialized urandom read (16 bytes
read, 24 bits of entropy available)
[ 2.470448] random: systemd: uninitialized urandom read (16 bytes
read, 25 bits of entropy available)
[ 2.497070] systemd[1]: systemd 232 running in system mode. (-PAM
-AUDIT -SELINUX -IMA -APPARMOR -SMACK +SYSVINIT -UTMP -LIBCRYPTSETUP
-GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
[ 2.516872] systemd[1]: Detected architecture arm.
Welcome to Poky (Yocto Project Reference Distro) 2.2+snapshot-20170307 (master)!
[ 2.560427] systemd[1]: Set hostname to <phyboard-wega-am335x-1>.
[ 2.713762] random: systemd-sysv-ge: uninitialized urandom read (16
bytes read, 26 bits of entropy available)
[ 2.727953] random: systemd-gpt-aut: uninitialized urandom read (16
bytes read, 26 bits of entropy available)
[ 2.744348] random: systemd-gpt-aut: uninitialized urandom read (16
bytes read, 27 bits of entropy available)
[ 2.760456] random: systemd-sysv-ge: uninitialized urandom read (16
bytes read, 27 bits of entropy available)
[ 2.865336] random: systemd: uninitialized urandom read (16 bytes
read, 30 bits of entropy available)
[ 2.876610] random: systemd: uninitialized urandom read (16 bytes
read, 30 bits of entropy available)
[ 2.887013] random: systemd: uninitialized urandom read (16 bytes
read, 31 bits of entropy available)
[ 2.897914] random: systemd: uninitialized urandom read (16 bytes
read, 31 bits of entropy available)
[ 3.109521] systemd[1]: Configuration file
/etc/systemd/system/ayran-startup.service is marked executable. Please
remove executable permission bits. Proceeding anyway.
[ 3.137479] systemd[1]: Listening on Network Service Netlink Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ 3.166414] systemd[1]: Started Forward Password Requests to Wall
Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ 3.196238] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 3.216171] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 3.236197] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 3.258139] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 3.276053] systemd[1]: dev-hugepages.mount: Couldn't determine
result for ConditionVirtualization=!private-users, assuming failed: No
such file or directory
[ 3.291506] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 3.316858] systemd[1]: Started Dispatch Password Requests to
Console Directory Watch.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ 3.346036] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 3.366357] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 3.390589] systemd[1]: Starting File System Check on Root Device...
Starting File System Check on Root Device...
[ 3.431628] systemd[1]: Starting Create list of required static
device nodes for the current kernel...
Starting Create list of required st…ce nodes for the current kernel...
[ 3.509434] systemd[1]: Mounting Configuration File System...
Mounting Configuration File System...
[ 3.544154] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 3.588380] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket[ 3.625559] systemd[1]:
Listening on Journal Audit Socket.
.
[ OK ] Listening on Journal Audit Socket.
[ 3.643360] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 3.659947] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 3.716684] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 3.786342] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 3.816266] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 3.854892] systemd[1]: Mounting Temporary Directory...
Mounting Temporary Directory...
[ 3.906615] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 3.950498] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 4.025285] systemd[1]: Mounted Configuration File System.
[ OK ] Mounted Configuration File System.
[ 4.086166] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 4.106144] systemd[1]: Mounted Temporary Directory.
[ OK ] Mounted Temporary Directory.
[ 4.126637] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Started File System Check on Root Device.
[ OK ] Started Create list of required sta…vice nodes for the current kernel.
[ OK ] Started Apply Kernel Variables.
Starting Create Static Device Nodes in /dev...
Starting Remount Root and Kernel File Systems...
[ OK ] Started Create Static Device Nodes in /dev.
[ 4.386626] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Starting udev Kernel Device Manager...
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Reached target Local File Systems (Pre).
Mounting /var/volatile...
Starting Flush Journal to Persistent Storage...
Starting udev Coldplug all Devices...
[ OK ] Mounted /var/volatile.
[ OK ] Started udev Kernel Device Manager.
[ 4.717758] systemd-journald[127]: Received request to flush
runtime journal from PID 1
[ OK ] Reached target Local File Systems.
[ OK ] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Started Create Volatile Files and Directories.
[ OK ] Found device /dev/ttyO0.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Reached target System Initialization.
Starting sshd.socket.
[ 5.741723] vdig1_1p8v: supplied by vcc5vDirectories.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Listening on sshd.socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started Rauc Good-marking Service.
[ OK ] Started Kernel Logging Service.
Starting ACPI Event Daemon...
[ OK ] Reached target Containers.
[ OK ] Started Serial Getty on ttyO0.
[ OK ] Started D-Bus System Message Bus.
Starting Network Service...
[ OK ] Started can0 interface setup.
[ OK ] Started Getty on tty1.
[ 6.844938] c_can_platform 481d0000.can can0: setting BTR=0209 BRPE=0000
[ OK ] Reached target Login Prompts.
[ OK ] Started System Logging Service.
[ 6.955550] IPv6: ADDRCONF(NETDEV_CHANGE): can0: link becomes ready
[ OK ] Started ACPI Event Daemon.
[ 7.263422] [drm] Initialized pvr 1.14.3699939 20110701 on minor 0
[ 7.418688] davinci_evm sound_iface: tlv320aic3x-hifi <->
48038000.mcasp mapping ok
[ OK ] Started Network Service.
[ 7.672754] net eth1: initializing cpsw version 1.12 (0)
[ 7.678363] net eth0: initialized cpsw ale version 1.4
[ 7.683746] net eth0: ALE Table size 1024
[ 7.926395] net eth1: phy found : id is : 0x7c0f1
[ 7.961977] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 7.968187] 8021q: adding VLAN 0 to HW filter on device eth1
[ OK ] Reached target Network.
[ 8.132915] net eth0: initializing cpsw version 1.12 (0)
Starting Lightning Fast Webserver With Light System Requirements...
Starting Network Name Resolution...
[ 8.286327] net eth0: phy found : id is : 0x7c0f1
[ 8.295686] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.301807] 8021q: adding VLAN 0 to HW filter on device eth0
[ OK ] Started Lightning Fast Webserver With Light System Requirements.
[ OK ] Reached target Sound Card.
[ OK ] Started Network Name Resolution.
[ OK ] Reached target Multi-User System.
Starting Startup service for dhcp-client...
[ 11.306373] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full
- flow control rx/tx
[ 11.314870] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Poky (Yocto Project Reference Distro) 2.2+snapshot-20170307
phyboard-wega-am335x-1 ttyO0
phyboard-wega-am335x-1 login:
Thank you for your time.
Sincerely,
2017-03-17 10:39 GMT+03:00 Sascha Hauer <s.hauer@pengutronix.de>:
> Hi,
>
> On Thu, Mar 16, 2017 at 04:55:07PM +0300, Çağlar Kilimci wrote:
>> Hello all,
>>
>> As my general purpose of updating a system with RUAC [1], I need to
>> use Barebox State Framework but I could not run it properly. I have
>> appended Barebox config these:
>>
>> CONFIG_STATE=y
>> CONFIG_STATE_CRYPTO=y
>> CONFIG_CMD_SHA1SUM=y
>> CONFIG_CMD_SHA224SUM=y
>> CONFIG_CMD_SHA256SUM=y
>> CONFIG_CMD_SHA384SUM=y
>> CONFIG_CMD_SHA512SUM=y
>> CONFIG_CMD_STATE=y
>> CONFIG_STATE_DRV=y
>> CONFIG_DIGEST_HMAC=y
>> CONFIG_DIGEST_SHA1_GENERIC=y
>> CONFIG_DIGEST_HMAC_GENERIC=y
>> CONFIG_CRYPTO_KEYSTORE=y
>> CONFIG_BOOTCHOOSER=y
>> CONFIG_CMD_BOOTCHOOSER=y
>>
>> And also, I include below into my dts:
>> state: state@0 {
>> magic = <0x27031977>;
>> compatible = "barebox,state";
>> backend-type = "raw";
>> backend = "partname:state";
>
> This looks wrong. This should be a phandle pointing to the partition you
> want to use.
>
> Otherwise it looks ok. Could you provide a boot log?
>
> Sascha
>
> --
> Pengutronix e.K. | |
> Industrial Linux Solutions | http://www.pengutronix.de/ |
> Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
--
Çağlar Kilimci
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 4+ messages in thread