* [PATCH v1] Documentation: imx: add documentation for RioTboard
@ 2019-04-30 7:01 Oleksij Rempel
2019-04-30 7:10 ` Andrey Smirnov
0 siblings, 1 reply; 3+ messages in thread
From: Oleksij Rempel @ 2019-04-30 7:01 UTC (permalink / raw)
To: barebox; +Cc: Oleksij Rempel
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
.../boards/imx/embest-i.mx6s-riotboard.rst | 133 ++++++++++++++++++
1 file changed, 133 insertions(+)
create mode 100644 Documentation/boards/imx/embest-i.mx6s-riotboard.rst
diff --git a/Documentation/boards/imx/embest-i.mx6s-riotboard.rst b/Documentation/boards/imx/embest-i.mx6s-riotboard.rst
new file mode 100644
index 0000000000..17b630daea
--- /dev/null
+++ b/Documentation/boards/imx/embest-i.mx6s-riotboard.rst
@@ -0,0 +1,133 @@
+Embest RIoTboard
+================
+
+RIoTboard Standard kit
+----------------------
+
+http://www.embest-tech.com/prod_view.aspx?TypeId=74&Id=345&FId=t3:74:3
+
+General Features:
+ * Product Dimensions: 75mm x 120mm
+ * Operating Temperature: 0 ~ 50℃
+ * Operating Humidity: 20% ~ 90% (non-condensing)
+ * DC-in：5V/4A
+
+Processor:
+ * i.MX 6Solo based on ARM Cortex™-A9
+ * 32 Kbyte L1 instruction buffer
+ * 32 Kbyte L1 data buffer
+ * Private counter and watchdog
+ * Cortex-A9 NEON MPE (media processing engine) coprocessor
+
+On-Board Memories:
+ * 4GByte eMMC
+ * 2*512MB DDR3 SDRAM
+
+One-Board Interfaces/Buttons:
+
+ * Audio input/output interfaces
+ * A LVDS interface
+ * A HDMI interface
+ * A LCD display interface (expansion interface)
+ * A digital camera interface
+ * A MIPI interface
+ * 4 TTL-level serial interfaces (one for debugging, the rest for expansion)
+ * 4 high-speed USB2.0 host interfaces (480Mbps)
+ * A high-speed USB2.0 OTG interface (480Mbps)
+ * A SD card slot
+ * A TF card slot
+ * A 10/100M/1Gbps RJ45 interface
+ * 2 I2C interfaces (expansion interfaces)
+ * 2 SPI interfaces (expansion interfaces)
+ * 3 PWM interfaces (expansion interfaces)
+ * A GPIO interface (expansion interfaces)
+ * A JTAG interface
+ * A boot-mode switch
+ * 4 LEDs (1 system LED, 2 custom LED, 1 open SDA LED)
+ * A reset button
+
+How to build barebox for Embest RIoTboard
+-----------------------------------------
+
+Using the default configuration:
+
+.. code-block:: sh
+
+ make ARCH=arm imx_v7_defconfig
+
+Build the binary image:
+
+.. code-block:: sh
+
+ make ARCH=arm CROSS_COMPILE=armv7compiler
+
+.. note:: replace ``armv7compiler`` with your ARM v7 cross compiler prefix,
+ e.g.: ``arm-linux-gnueabihf-``
+
+The resulting binary image to be flashed will be ``images/barebox-embest-imx6s-riotboard.img``.
+
+Replacing U-Boot with barebox
+-----------------------------
+
+ 1. Connect to the boards's UART (115200 8N1);
+
+ 2. Turn board's power on;
+
+ 3. Wait ``Hit any key to stop autoboot: 2`` prompt and press any key;
+
+ 4. Upload barebox image to the board via tftp and start it
+
+.. code-block:: none
+
+ MX6Solo RIoTboard U-Boot > setenv ethaddr d2:2d:ce:88:f4:f1
+ MX6Solo RIoTboard U-Boot > tftpboot 0x20800000 192.168.23.4:ore-barebox-riotboard
+ ----phy_addr=0x4, id= 0x4dd072
+ FEC: Link is Up 796d
+ Using FEC0 device
+ TFTP from server 192.168.23.4; our IP address is 192.168.1.103
+ Filename 'ore-barebox-riotboard'.
+ Load address: 0x20800000
+ Loading: ## Warning: gatewayip needed but not set
+ ## Warning: gatewayip needed but not set
+ ############################################
+ done
+ Bytes transferred = 637947 (9bbfb hex)
+ MX6Solo RIoTboard U-Boot > go 0x20800000
+
+ tarting application at 0x20800000 ...
+
+ barebox 2019.04.0-00151-g86762248de #391 Mon Apr 29 14:41:58 CEST 2019
+
+ Board: RIoTboard i.MX6S
+ detected i.MX6 Solo revision 1.1
+ i.MX reset reason POR (SRSR: 0x00000001)
+ mdio_bus: miibus0: probed
+ imx-usb 2184200.usb@2184200.of: USB EHCI 1.00
+ imx-esdhc 2194000.usdhc@2194000.of: registered as mmc1
+ imx-esdhc 2198000.usdhc@2198000.of: registered as mmc2
+ imx-esdhc 219c000.usdhc@219c000.of: registered as mmc3
+ imx-ipuv3 2400000.ipu@2400000.of: IPUv3H probed
+ imx-hdmi 120000.hdmi@120000.of: Detected HDMI controller 0x13:0x1a:0xa0:0xc1
+ netconsole: registered as netconsole-1
+ malloc space: 0x2fefb5e0 -> 0x4fdf6bbf (size 511 MiB)
+ mmc3: detected MMC card version 4.41
+ mmc3: registered mmc3.boot0
+ mmc3: registered mmc3.boot1
+ mmc3: registered mmc3
+ partition mmc3.3 not completely inside device mmc3
+ mmc3: Failed to register partition 3 on mmc3 (-22)
+ envfs: no envfs (magic mismatch) - envfs never written?
+ running /env/bin/init...
+
+ Hit m for menu or any key to stop autoboot: 2
+
+ type exit to get to the menu
+ barebox@RIoTboard i.MX6S:/
+..
+
+ 5. Install barebox to the eMMC
+
+.. code-block:: none
+
+ barebox@RIoTboard i.MX6S:/ cp /mnt/tftp/ore-barebox-riotboard /dev/mmc3.barebox
+..
--
2.20.1
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v1] Documentation: imx: add documentation for RioTboard
2019-04-30 7:01 [PATCH v1] Documentation: imx: add documentation for RioTboard Oleksij Rempel
@ 2019-04-30 7:10 ` Andrey Smirnov
2019-04-30 7:14 ` Oleksij Rempel
0 siblings, 1 reply; 3+ messages in thread
From: Andrey Smirnov @ 2019-04-30 7:10 UTC (permalink / raw)
To: Oleksij Rempel; +Cc: Barebox List
On Tue, Apr 30, 2019 at 12:01 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
> .../boards/imx/embest-i.mx6s-riotboard.rst | 133 ++++++++++++++++++
> 1 file changed, 133 insertions(+)
> create mode 100644 Documentation/boards/imx/embest-i.mx6s-riotboard.rst
>
> diff --git a/Documentation/boards/imx/embest-i.mx6s-riotboard.rst b/Documentation/boards/imx/embest-i.mx6s-riotboard.rst
> new file mode 100644
> index 0000000000..17b630daea
> --- /dev/null
> +++ b/Documentation/boards/imx/embest-i.mx6s-riotboard.rst
> @@ -0,0 +1,133 @@
> +Embest RIoTboard
> +================
> +
> +RIoTboard Standard kit
> +----------------------
> +
> +http://www.embest-tech.com/prod_view.aspx?TypeId=74&Id=345&FId=t3:74:3
> +
> +General Features:
> + * Product Dimensions: 75mm x 120mm
> + * Operating Temperature: 0 ~ 50℃
> + * Operating Humidity: 20% ~ 90% (non-condensing)
> + * DC-in：5V/4A
> +
> +Processor:
> + * i.MX 6Solo based on ARM Cortex™-A9
> + * 32 Kbyte L1 instruction buffer
> + * 32 Kbyte L1 data buffer
> + * Private counter and watchdog
> + * Cortex-A9 NEON MPE (media processing engine) coprocessor
> +
> +On-Board Memories:
> + * 4GByte eMMC
> + * 2*512MB DDR3 SDRAM
> +
> +One-Board Interfaces/Buttons:
> +
> + * Audio input/output interfaces
> + * A LVDS interface
> + * A HDMI interface
> + * A LCD display interface (expansion interface)
> + * A digital camera interface
> + * A MIPI interface
> + * 4 TTL-level serial interfaces (one for debugging, the rest for expansion)
> + * 4 high-speed USB2.0 host interfaces (480Mbps)
> + * A high-speed USB2.0 OTG interface (480Mbps)
> + * A SD card slot
> + * A TF card slot
> + * A 10/100M/1Gbps RJ45 interface
> + * 2 I2C interfaces (expansion interfaces)
> + * 2 SPI interfaces (expansion interfaces)
> + * 3 PWM interfaces (expansion interfaces)
> + * A GPIO interface (expansion interfaces)
> + * A JTAG interface
> + * A boot-mode switch
> + * 4 LEDs (1 system LED, 2 custom LED, 1 open SDA LED)
> + * A reset button
> +
> +How to build barebox for Embest RIoTboard
> +-----------------------------------------
> +
> +Using the default configuration:
> +
> +.. code-block:: sh
> +
> + make ARCH=arm imx_v7_defconfig
> +
> +Build the binary image:
> +
> +.. code-block:: sh
> +
> + make ARCH=arm CROSS_COMPILE=armv7compiler
> +
> +.. note:: replace ``armv7compiler`` with your ARM v7 cross compiler prefix,
> + e.g.: ``arm-linux-gnueabihf-``
> +
> +The resulting binary image to be flashed will be ``images/barebox-embest-imx6s-riotboard.img``.
> +
> +Replacing U-Boot with barebox
> +-----------------------------
> +
> + 1. Connect to the boards's UART (115200 8N1);
> +
> + 2. Turn board's power on;
> +
> + 3. Wait ``Hit any key to stop autoboot: 2`` prompt and press any key;
> +
> + 4. Upload barebox image to the board via tftp and start it
> +
> +.. code-block:: none
> +
> + MX6Solo RIoTboard U-Boot > setenv ethaddr d2:2d:ce:88:f4:f1
> + MX6Solo RIoTboard U-Boot > tftpboot 0x20800000 192.168.23.4:ore-barebox-riotboard
> + ----phy_addr=0x4, id= 0x4dd072
> + FEC: Link is Up 796d
> + Using FEC0 device
> + TFTP from server 192.168.23.4; our IP address is 192.168.1.103
> + Filename 'ore-barebox-riotboard'.
> + Load address: 0x20800000
> + Loading: ## Warning: gatewayip needed but not set
> + ## Warning: gatewayip needed but not set
> + ############################################
> + done
> + Bytes transferred = 637947 (9bbfb hex)
> + MX6Solo RIoTboard U-Boot > go 0x20800000
> +
> + tarting application at 0x20800000 ...
Not that it changes much, but is this a copy past mishap, or is "S"
(or "s") in "starting" above really missing?
Thanks,
Andrey Smirnov
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v1] Documentation: imx: add documentation for RioTboard
2019-04-30 7:10 ` Andrey Smirnov
@ 2019-04-30 7:14 ` Oleksij Rempel
0 siblings, 0 replies; 3+ messages in thread
From: Oleksij Rempel @ 2019-04-30 7:14 UTC (permalink / raw)
To: Andrey Smirnov, barebox
On 30.04.19 09:10, Andrey Smirnov wrote:
> On Tue, Apr 30, 2019 at 12:01 AM Oleksij Rempel <o.rempel@pengutronix.de> wrote:
>>
>> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
>> ---
>> .../boards/imx/embest-i.mx6s-riotboard.rst | 133 ++++++++++++++++++
>> 1 file changed, 133 insertions(+)
>> create mode 100644 Documentation/boards/imx/embest-i.mx6s-riotboard.rst
>>
>> diff --git a/Documentation/boards/imx/embest-i.mx6s-riotboard.rst b/Documentation/boards/imx/embest-i.mx6s-riotboard.rst
>> new file mode 100644
>> index 0000000000..17b630daea
>> --- /dev/null
>> +++ b/Documentation/boards/imx/embest-i.mx6s-riotboard.rst
>> @@ -0,0 +1,133 @@
>> +Embest RIoTboard
>> +================
>> +
>> +RIoTboard Standard kit
>> +----------------------
>> +
>> +http://www.embest-tech.com/prod_view.aspx?TypeId=74&Id=345&FId=t3:74:3
>> +
>> +General Features:
>> + * Product Dimensions: 75mm x 120mm
>> + * Operating Temperature: 0 ~ 50℃
>> + * Operating Humidity: 20% ~ 90% (non-condensing)
>> + * DC-in：5V/4A
>> +
>> +Processor:
>> + * i.MX 6Solo based on ARM Cortex™-A9
>> + * 32 Kbyte L1 instruction buffer
>> + * 32 Kbyte L1 data buffer
>> + * Private counter and watchdog
>> + * Cortex-A9 NEON MPE (media processing engine) coprocessor
>> +
>> +On-Board Memories:
>> + * 4GByte eMMC
>> + * 2*512MB DDR3 SDRAM
>> +
>> +One-Board Interfaces/Buttons:
>> +
>> + * Audio input/output interfaces
>> + * A LVDS interface
>> + * A HDMI interface
>> + * A LCD display interface (expansion interface)
>> + * A digital camera interface
>> + * A MIPI interface
>> + * 4 TTL-level serial interfaces (one for debugging, the rest for expansion)
>> + * 4 high-speed USB2.0 host interfaces (480Mbps)
>> + * A high-speed USB2.0 OTG interface (480Mbps)
>> + * A SD card slot
>> + * A TF card slot
>> + * A 10/100M/1Gbps RJ45 interface
>> + * 2 I2C interfaces (expansion interfaces)
>> + * 2 SPI interfaces (expansion interfaces)
>> + * 3 PWM interfaces (expansion interfaces)
>> + * A GPIO interface (expansion interfaces)
>> + * A JTAG interface
>> + * A boot-mode switch
>> + * 4 LEDs (1 system LED, 2 custom LED, 1 open SDA LED)
>> + * A reset button
>> +
>> +How to build barebox for Embest RIoTboard
>> +-----------------------------------------
>> +
>> +Using the default configuration:
>> +
>> +.. code-block:: sh
>> +
>> + make ARCH=arm imx_v7_defconfig
>> +
>> +Build the binary image:
>> +
>> +.. code-block:: sh
>> +
>> + make ARCH=arm CROSS_COMPILE=armv7compiler
>> +
>> +.. note:: replace ``armv7compiler`` with your ARM v7 cross compiler prefix,
>> + e.g.: ``arm-linux-gnueabihf-``
>> +
>> +The resulting binary image to be flashed will be ``images/barebox-embest-imx6s-riotboard.img``.
>> +
>> +Replacing U-Boot with barebox
>> +-----------------------------
>> +
>> + 1. Connect to the boards's UART (115200 8N1);
>> +
>> + 2. Turn board's power on;
>> +
>> + 3. Wait ``Hit any key to stop autoboot: 2`` prompt and press any key;
>> +
>> + 4. Upload barebox image to the board via tftp and start it
>> +
>> +.. code-block:: none
>> +
>> + MX6Solo RIoTboard U-Boot > setenv ethaddr d2:2d:ce:88:f4:f1
>> + MX6Solo RIoTboard U-Boot > tftpboot 0x20800000 192.168.23.4:ore-barebox-riotboard
>> + ----phy_addr=0x4, id= 0x4dd072
>> + FEC: Link is Up 796d
>> + Using FEC0 device
>> + TFTP from server 192.168.23.4; our IP address is 192.168.1.103
>> + Filename 'ore-barebox-riotboard'.
>> + Load address: 0x20800000
>> + Loading: ## Warning: gatewayip needed but not set
>> + ## Warning: gatewayip needed but not set
>> + ############################################
>> + done
>> + Bytes transferred = 637947 (9bbfb hex)
>> + MX6Solo RIoTboard U-Boot > go 0x20800000
>> +
>> + tarting application at 0x20800000 ...
>
> Not that it changes much, but is this a copy past mishap, or is "S"
> (or "s") in "starting" above really missing?
Uff.. right. It is mishap. thx!
Kind regards,
Oleksij Rempel
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2019-04-30 7:14 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-04-30 7:01 [PATCH v1] Documentation: imx: add documentation for RioTboard Oleksij Rempel
2019-04-30 7:10 ` Andrey Smirnov
2019-04-30 7:14 ` Oleksij Rempel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox