Re: ARM: socfpga: enclustra-sa2: issue with I2C1

[David Picard <david.picard@clermont.in2p3.fr>]

Generate the handoff files manually: is it what the bsp-create-settings 
script from Intel's embedded shell does? I did run it.

I understand that socfpga_import_preloader mostly only reformats the files.


Le 27/04/2026 à 14:25, Steffen Trumtrar a écrit :
> On 2026-04-27 at 14:13 +02, David Picard 
> <david.picard@clermont.in2p3.fr> wrote:
>
>> Too bad you don't have an idea. Sorry for misspelling your name,
>>
>
> no problem ;)
>
>>
>> I'm not sure it's related, but I get errors with the 
>> socfpga_import_preloader
>> script only if I use the --embedded-sdk option. I couldn't figure out 
>> what this
>> option changes.
>> https://paste.debian.net/hidden/fffbb190
>>
>
> Hm, the script is obviously pretty hacked together and not very error 
> proof.
> With the embedded-sdk provided, it generates the handoff-files without 
> the
> option, the handoff files need to be generated manually.
>
> Maybe the Python script in the SDK changed since adding this option 
> and doesn't
> copy the files that are stat'ed.
>
>
> Steffen
>
>> David
>>
>> Le 27/04/2026 à 12:20, Steffen Trumtrar a écrit :
>> > On 2026-04-27 at 12:09 +02, David Picard 
>> <david.picard@clermont.in2p3.fr>
>> > wrote:
>> >
>> > Hi,
>> >
>> >> Hi Stephen, thanks for your reply,
>> >>
>> >> Pins SDA and SCL, GPIO51 and GPIO52 respectively, are specified 
>> with the I/O
>> >> standard 3.3V LVCMOS and a drive strength of 2mA, which is way 
>> more than
>> >> needed,
>> >> given my 10K pull-up resistors (3.3 / 10K = 0.33mA). I know that 
>> 10K is
>> >> bigger
>> >> than the usual 2.2K, but probably not big enough to prevent any 
>> change on the
>> >> SCL line. I just see a perfect flat line when I probe the bus.
>> >>
>> >
>> > :(
>> >
>> >> I compared iocsr_config_cyclone5.c and pinmux_config.c in the
>> >> terasic-de10-nano/
>> >> and enclustra-sa2/ directories. There are a lot of differences. 
>> But the lines
>> >> that changed in enclustra-sa2/ when I tried to enable the I2C1 bus 
>> are now
>> >> the
>> >> same as in the terasic-de10-nano/ directory, which probably makes 
>> sense.
>> >>
>> >
>> > Makes sence, yes and was what I hoped for. But, doesn't seem to change
>> > anything.
>> >
>> >> Does Barebox have to decipher every bit in those cryptic files?
>> >>
>> >
>> > barebox knows nothing about the meaning of the iocsr registers. 
>> Those values a
>> > just written to the hardware and can't be changed afterwards.
>> > AFAIK there still is no linux driver that might read and decipher the
>> > settings.
>> >
>> > Sadly, I don't have any more ideas at the top of my head why it 
>> doesn't work.
>> > Everything sounds correct.
>> >
>> >
>> > Best regards,
>> > Steffen
>> >
>> >>
>> >> David
>> >>
>> >>
>> >> Le 24/04/2026 à 09:27, Steffen Trumtrar a écrit :
>> >> > On 2026-04-23 at 14:00 +02, David Picard 
>> <david.picard@clermont.in2p3.fr>
>> >> > wrote:
>> >> >
>> >> > Hi,
>> >> >
>> >> >> Hello,
>> >> >>
>> >> >> @Stephen and Ian: I Cc you since I spotted you authored commits 
>> related to
>> >> >> Intel
>> >> >> SoC FPGA pin muxing.
>> >> >>
>> >> >
>> >> > long time ago ;)
>> >> >
>> >> >> I'm trying to enable the I2C1 bus on a Cyclone V-base module, 
>> mounted on a
>> >> >> base
>> >> >> board. The I2C1 lines connect to a 2.54mm header, on which I 
>> attached a
>> >> I²C
>> >> >> device with pull-up resistors at address 0x40.
>> >> >> 
>> https://www.enclustra.com/en/products/system-on-chip-modules/mercury-sa2/
>> >> I
>> >> >> can't detect the I²C device, nor can I see any pulse on the SCL 
>> line,
>> >> which
>> >> >> is
>> >> >> constantly at +3.3V.
>> >> >>
>> >> >> I changed the pin muxing in Quartus, updated the handoff files, 
>> changed
>> >> the
>> >> >> devicetree. The I2C1 bus is visible in Barebox and Linux. More 
>> detail
>> >> here:
>> >> >>
>> >> 
>> https://community.altera.com/discussions/fpga-device/cyclone-v-hps-i2c1-issue-no-activity-on-bus/352583
>> >> >
>> >> > I remember, that iocsr was 'underdocumented' to say the least...
>> >> >
>> >> > Wasn't it possible to change drive strength and those settings 
>> or was that
>> >> > with Xilinx/Zynq?
>> >> >
>> >> >> As documented on the Barebox website, I generated the BSP files 
>> with the
>> >> >> Quartus
>> >> >> script bsp-create-settings and copied the handoff files to the 
>> Barebox
>> >> build
>> >> >> directory. After that, I could see that iocsr_config_cyclone5.c 
>> and
>> >> >> pinmux_config.c had changed.
>> >> >>
>> >> 
>> https://www.barebox.org/doc/2025.05.0/boards/socfpga.html#updating-handoff-files
>> >> >>
>> >> 
>> https://www.intel.com/content/www/us/en/docs/programmable/683187/20-1/bsp-create-settings.html
>> >> >> If someone could give me some hint, that would be really great!
>> >> >
>> >> > I see, that the Terasic DE10 Nano uses i2c1. Maybe compare the 
>> changed
>> >> iocsr
>> >> > with those?
>> >> >
>> >> >
>> >> > Best regards,
>> >> > Steffen
>> >> >
>> >
>