mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Sascha Hauer <sha@pengutronix.de>
To: Barebox List <barebox@lists.infradead.org>
Subject: v2021.11.0
Date: Mon, 15 Nov 2021 14:20:49 +0100	[thread overview]
Message-ID: <20211115132049.GB6556@pengutronix.de> (raw)

Hi All,

barebox-2021.11.0 is out. Worth mentioning this time is a new SoC
supported: RISC-V Litex. Also we have i.MX8MN-EVK and Xilinx zcu106
board support. There are some new drivers as well: virtio network,
LiteX SPI flash support, LiteEth support and NXP IFC NAND support.

As usual, see below for a full list of changes.

Have Fun!
  Sascha

--------------------------------8<---------------------------------

Ahmad Fatoum (47):
      watchdog: imxwd: register explicit warm reset handler
      ARM: i.MX8MM: add reboot to serial download mode
      net: drop Calxeda Highbank xgmac driver support
      net: make ARC MAC driver 32-bit only
      asm-generic: include bitio.h from io.h
      x86: define phys_to_virt and virt_to_phys
      net: e1000: split EEPROM and barebox MTD wrapper into separate files
      Documentation: boards: at91: remove done TODOs
      ARM: at91: sam9_smc: register driver earlier
      ARM: AT91: migrate sama5d3-xplained to DT
      common: remove !SANDBOX dependency for target tools
      common: add new menu for target tools
      scripts: omap3-usb-loader: make proper use of pkg-config --cflags
      scripts: allow building USB loader tools for target as well
      arm64: Don't truncate upper 32 bits in ENTRY_FUNCTION arg registers
      ARM: i.MX8MP: move SCTR enabling into imx8mp_cpu_lowlevel_init
      ARM: at91: sama5d27_som1_ek: populate MAC address from EEPROM
      ARM: i.MX8MP: bbu: fix wrong flash header offset for eMMC boot partition
      ARM: i.MX8MP: EVK: change bbu handler from eMMC user to boot partition
      pinctrl: bcm2835: Probe driver earlier
      pinctrl: bcm2835: Add support for bcm2711
      mci: imx-esdhc-pbl: support eMMC boot partitions on i.MX8MP
      ARM: i.MX: add i.MX8MN (Nano) SoC support boilerplate
      clk: imx: add i.MX8MN (Nano) support
      ARM: i.MX8MN: adapt early clock support
      ARM: i.MX: extend drivers for i.MX8MN (Nano) support
      ddr: imx8m: add i.MX8MN (Nano) support
      ddr: imx8m: ddrphy_train: add DDR4 support
      scripts: imx: add i.MX8MN support to imx-image
      ARM: i.MX8MN: add i.MX8MN-EVK support
      net: add virtio network driver
      fs: remove unused struct fs_device_d::parent_device
      Documentation: framebuffer: remove note about lack of backlight support
      video: simplefb-client: populate video mode field
      video: simplefb-client: make probe less verbose
      commands: smc: disable -c (start cpu) test option for ARMv8
      ARM: document arm_setup_stack() pitfalls
      RISC-V: virt: support poweroff/restart on tinyemu
      console: fixup add new CONFIG_CONSOLE_DISABLE_INPUT option
      ARM: Rockchip: fix path to rkbin firmware in documentation
      ARM: psci: client: fix power off and reset via 64-bit secure monitor
      ARM: i.MX8M: nxp-imx8mn-evk: use regular i2c read for device detection
      net: designware: eqos: fix MDIO regression for STM32MP1 boards
      mci: dw_mmc: make reset control optional again
      pci: efi: skip driver model fixup for non-EFI PCI busses
      efi: efi-iomem: don't add EFI loader code/data as memory banks
      efi: efi-iomem: fix erroneous use of IS_ENABLED()

Andrej Picej (1):
      hush: fix conditional statements exit code

Antony Pavlov (9):
      clocksource: timer-riscv: select CSR from device tree
      serial: add litex UART driver
      console: support set baudrate for fixed baudrate drivers
      gpio: add driver for 74xx-ICs with MMIO access
      mtd: core: fix whitespaces
      spi: add litex spiflash driver
      net: add LiteEth driver
      RISC-V: add LiteX SoC and linux-on-litex-vexriscv support
      RISC-V: add litex_linux_defconfig

Daniel Brát (1):
      ARM: rpi_defconfig: Enable PHY core for dwc2 USB driver

Ian Abbott (2):
      ARM: Terasic DE0-Nano-SoC/Atlas-SoC: Use upstream compatible string
      ARM: Terasic SoCkit: Use upstream compatible string

Jules Maselbas (2):
      common: Select CRC32 dependency for DEFAULT_ENVIRONMENT
      usb: gadget: dfu: Rework dfu command to use usbgadget

Karfich, Oleg (1):
      net: cpsw: fix ethernet bringup in case of a fixed-link phy

Marcelo Politzer (1):
      serial: implement riscv SBI console support

Marco Felsch (5):
      scripts: bareboxenv: add erase hint if build as host-tool
      ARM: i.MX6: boot: detect USB serial downloader more reliable
      fastboot net: add setter for global.fastboot.net.autostart
      usb: imx-us-phy: add vbus_valid ro parameter
      state: backend_raw: fix ignoring unpack failures

Michael Riesch (4):
      arm: rockchip-rk3568-evb: add hardware id detection
      arm: zynqmp: add support for xilinx zcu106 board
      Documentation: boards: zynqmp: fix broken links
      arm: zynqmp: add boot source support

Michael Tretter (4):
      firmware: zynqmp-fpga: initialize flags at function start
      firmware: zynqmp-fpga: avoid additional buffer for size argument
      firmware: zynqmp-fpga: do not use DMA coherent memory for bitstream
      ARM: zynqmp: use std_file_update as update handler

Oleksij Rempel (4):
      ARM: boards: protonic-imx6: enable deep-probe support
      ARM: boards: protonic-imx6: use decode error values instead error numbers.
      net: dhcp: send current hostname as part of the DHCP request
      net: dhcp: set default DHCP vendor ID to "barebox"

Renaud Barbier (3):
      ARM: atomic.h: add 64-bit counter support
      nand: add NXP IFC nand driver
      ls1046ardb: enable IFC NAND.

Robin van der Gracht (8):
      ARM: boards: protonic-imx6: Run usb boot entry instead of bare device
      ARM: boards: protonic-imx6: Don't fixup MAC address for disabled device
      ARM: dts: imx6dl-prtvt7: Add brand state variable
      ARM: boards: protonic-imx6: Don't register SD with bbu
      ARM: boards: protonic-imx6: Add emmc_usdhc machine data variable
      ARM: boards: protonic-imx6: Enable bootchooser on prti6g board
      ARM: boards: protonic-imx6: Skip usb check on prtvt7 by default
      ARM: boards: protonic-imx6: Add support for jozacp board

Rouven Czerwinski (4):
      file_list: add file_list_parse_null()
      fastboot: use file_list_parse_null()
      console: add new CONFIG_CONSOLE_DISABLE_INPUT option
      net: eqos: let phy_resume handle fixed link phys

Sascha Hauer (25):
      dts: update to v5.14-rc1
      dts: update to v5.14-rc2
      dts: update to v5.14-rc3
      dts: update to v5.14-rc4
      dts: update to v5.14-rc5
      dts: update to v5.14-rc6
      ARM: i.MX8m: Add of_compatible imd tags for i.MX8 boards
      dts: update to v5.14-rc7
      dts: update to v5.14
      dts: update to v5.15-rc1
      dts: update to v5.15-rc2
      dts: update to v5.15-rc3
      Merge branch 'for-next/arm'
      Merge branch 'for-next/at91'
      dts: update to v5.15-rc4
      Merge branch 'for-next/dts'
      Merge branch 'for-next/imx'
      Merge branch 'for-next/layerscape'
      Merge branch 'for-next/misc'
      Merge branch 'for-next/protonic'
      Merge branch 'for-next/riscv'
      Merge branch 'for-next/targettools'
      Merge branch 'for-next/zynqmp'
      sandbox: Fix stickypage.bin dependencies
      Release v2021.11.0

Steffen Trumtrar (2):
      scripts: socfpga_import_preloader: make sdk optional
      mci: sdhci: fix big-endian write for blockcount/size

Trent Piepho (2):
      ddr: imx8m: Rework ddrphy code and fix DDR-1067 on iMX8MM
      kbuild: dtc: Allow adding device tree fragments via config

Ulrich Ölmann (3):
      common: Kconfig: fix typos
      common: Kconfig: fix indentation
      Documentation: reboot-mode: fix typos

Uwe Kleine-König (6):
      arm/mvebu: sync barebox-arm-head.h to generic variant
      arm: mxs: Replace license and copyright boilerplate by SPDX identifiers
      mci: imx-esdhc-pbl: Fix two typos in a comment
      mci-bcm2835: Don't block infinitely while waiting for a command completion
      mci-bcm2835: Fix return type handling of bcm2835_mci_wait_command_done()
      mci: Improve error message for non-existent vmmc regulator
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox


                 reply	other threads:[~2021-11-15 13:22 UTC|newest]

Thread overview: [no followups] expand[flat|nested]  mbox.gz  Atom feed

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20211115132049.GB6556@pengutronix.de \
    --to=sha@pengutronix.de \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox