Re: [PATCH v1] net: phy: do not call adjust_link() form phy_device_attach()

[Sascha Hauer <sha@pengutronix.de>]

On Thu, Apr 14, 2022 at 09:55:30AM +0200, Oleksij Rempel wrote:
> phy_device_attach() is usually called from eth_open() to enable
> interface, configure MAC, etc. Some times we have situations like this:
> 1. find and configure PHY
> 2. define PHY as clock provider for MAC
> 3. reset and configure MAC
> 4. detect link and speed and configure MAC accordingly.
> 
> Which works as expected unless we use fixed PHY. Since fixed-phy was
> handled differently by the PHY code, we did step 4. before step 3. In
> this case we will loose MAC speed configuration at least on designware-eqos
> Ethernet controller.
> 
> With this change, we handle real PHY and virtual fixed-PHY in the same way.
> So, adjust_link() (step 4.) will be called after edev->open() (step 3.)
> as it should be for both variants.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/net/phy/phy.c | 13 ++++++++-----
>  1 file changed, 8 insertions(+), 5 deletions(-)

Applied, thanks

Sascha

> 
> diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> index 85cdd7862f..adff9dadd1 100644
> --- a/drivers/net/phy/phy.c
> +++ b/drivers/net/phy/phy.c
> @@ -54,6 +54,13 @@ int phy_update_status(struct phy_device *phydev)
>  			return ret;
>  	}
>  
> +	/*
> +	 * If the phy is a fixed-link, set it to active state to trigger
> +	 * MAC configuration
> +	 */
> +	if (!phydev->bus && !phydev->link)
> +		phydev->link = 1;
> +
>  	if (phydev->speed == oldspeed && phydev->duplex == oldduplex &&
>  	    phydev->link == oldlink)
>  		return 0;
> @@ -311,7 +318,7 @@ struct phy_device *of_phy_register_fixed_link(struct device_node *np,
>  
>  	phydev->dev.parent = &edev->dev;
>  	phydev->registered = 1;
> -	phydev->link = 1;
> +	phydev->link = 0;
>  
>  	if (of_property_read_u32(np, "speed", &phydev->speed))
>  		return NULL;
> @@ -401,10 +408,6 @@ static int phy_device_attach(struct phy_device *phy, struct eth_device *edev,
>  
>  	phy->adjust_link = adjust_link;
>  
> -	/* If the phy is a fixed-link, then call adjust_link directly */
> -	if (!phy->bus && adjust_link)
> -		adjust_link(edev);
> -
>  	return 0;
>  }
>  
> -- 
> 2.30.2
> 
> 
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox