From: Ahmad Fatoum <a.fatoum@pengutronix.de>
To: Sascha Hauer <s.hauer@pengutronix.de>,
Barebox List <barebox@lists.infradead.org>
Subject: Re: [PATCH 00/22] Add initial Texas Instruments K3 support
Date: Thu, 2 Nov 2023 15:12:25 +0100 [thread overview]
Message-ID: <7b035953-f359-f616-9d90-df37da1890a1@pengutronix.de> (raw)
In-Reply-To: <20230803105003.4088205-1-s.hauer@pengutronix.de>
Hello Sascha,
On 03.08.23 12:49, Sascha Hauer wrote:
> This series adds initial basic support for the TI K3 Architecture.
> Currently only the AM62x is supported and within there the BeaglePlay
> board (https://www.beagleboard.org/boards/beagleplay).
>
> The current support is enough for bringing up barebox 2nd stage after
> U-Boot has initialized the SoC. The SoC boots from a FAT partition on
> SD/eMMC, the u-boot.img therein can be replaced with a barebox image.
>
> The SoC has a core dedicated to handle clocks, power domains and other
> stuff. Communication to this core is done with a mailbox interface and
> this series contains patches to implement that interface based on that
> a clk driver and a power domain driver.
>
> So far only SD/eMMC is working, so there's plenty of room to add further
> support for networking, USB, SPI and I2C. It's a start.
let's merge this?
Cheers,
Ahmad
>
> Sascha
>
> Sascha Hauer (22):
> pm_domain: Add onecell support
> gpio: davinci: Redesign driver to accommodate ngpios in one gpio chip
> gpio: davinci: Add support for GPIO controllers on TI K3 SoCs
> ARM64: Add support for debug_ll on TI AM62x SoCs
> Add initial mailbox support
> mailbox: Add TI K3 Secure Proxy Driver
> serial: ns16550: Add support for UARTs on K3 SoCs
> firmware: Add basic support for TI System Control Interface (TI SCI)
> protocol
> lib: Add generic binary search function
> clk: Add K3 SCI clock driver
> soc: ti: Add ti_sci_pm_domains driver
> mci: fix define
> mci: make debugging output more useful
> mci: sdhci: Add common wait for idle function
> mci: sdhci: wait for idle before stopping clock
> mci: Add am654 SDHCI driver
> ARM: Add Texas Instruments K3 architecture
> ARM: k3: Add initial BeaglePlay board support
> ARM: k3: BeaglePlay: Work around non working SD card
> ARM: k3: BeaglePlay: generate FIT image
> doc: K3: Add documentation
> ARM: multi_v8_defconfig: Enable K3 SoCs
>
> Documentation/boards/k3.rst | 29 +
> arch/arm/Kconfig | 14 +
> arch/arm/Makefile | 1 +
> arch/arm/boards/Makefile | 1 +
> arch/arm/boards/beagleplay/Makefile | 1 +
> arch/arm/boards/beagleplay/entry.S | 29 +
> arch/arm/boards/beagleplay/lowlevel.c | 33 +
> arch/arm/configs/multi_v8_defconfig | 10 +-
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/k3-am625-beagleplay.dts | 30 +
> arch/arm/include/asm/debug_ll.h | 2 +
> arch/arm/mach-k3/Kconfig | 11 +
> arch/arm/mach-k3/Makefile | 1 +
> arch/arm/mach-k3/common.c | 24 +
> common/Kconfig | 16 +-
> drivers/Kconfig | 1 +
> drivers/Makefile | 1 +
> drivers/base/power.c | 76 +
> drivers/clk/Makefile | 1 +
> drivers/clk/ti-sci-clk.c | 630 ++++++
> drivers/firmware/Kconfig | 15 +
> drivers/firmware/Makefile | 1 +
> drivers/firmware/ti_sci.c | 2745 +++++++++++++++++++++++++
> drivers/firmware/ti_sci.h | 1533 ++++++++++++++
> drivers/gpio/Kconfig | 4 +-
> drivers/gpio/gpio-davinci.c | 70 +-
> drivers/mailbox/Kconfig | 22 +
> drivers/mailbox/Makefile | 2 +
> drivers/mailbox/mailbox.c | 92 +
> drivers/mailbox/ti-msgmgr.c | 402 ++++
> drivers/mci/Makefile | 1 +
> drivers/mci/am654-sdhci.c | 680 ++++++
> drivers/mci/arasan-sdhci.c | 13 +-
> drivers/mci/atmel-sdhci-common.c | 25 +-
> drivers/mci/dove-sdhci.c | 23 +-
> drivers/mci/mci-bcm2835.c | 13 +-
> drivers/mci/mci-core.c | 13 +-
> drivers/mci/rockchip-dwcmshc-sdhci.c | 16 +-
> drivers/mci/sdhci.c | 24 +
> drivers/mci/sdhci.h | 1 +
> drivers/serial/serial_ns16550.c | 6 +
> drivers/soc/Kconfig | 1 +
> drivers/soc/Makefile | 1 +
> drivers/soc/ti/Kconfig | 7 +
> drivers/soc/ti/Makefile | 1 +
> drivers/soc/ti/ti_sci_pm_domains.c | 196 ++
> images/Makefile | 10 +
> images/Makefile.k3 | 13 +
> images/k3-am625-beagleplay.its | 29 +
> include/linux/bsearch.h | 33 +
> include/linux/types.h | 2 +
> include/mach/k3/debug_ll.h | 49 +
> include/mailbox.h | 36 +
> include/mci.h | 4 +-
> include/pm_domain.h | 9 +
> include/soc/ti/k3-sec-proxy.h | 25 +
> include/soc/ti/ti_sci_protocol.h | 657 ++++++
> lib/Makefile | 1 +
> lib/bsearch.c | 34 +
> 59 files changed, 7596 insertions(+), 125 deletions(-)
> create mode 100644 Documentation/boards/k3.rst
> create mode 100644 arch/arm/boards/beagleplay/Makefile
> create mode 100644 arch/arm/boards/beagleplay/entry.S
> create mode 100644 arch/arm/boards/beagleplay/lowlevel.c
> create mode 100644 arch/arm/dts/k3-am625-beagleplay.dts
> create mode 100644 arch/arm/mach-k3/Kconfig
> create mode 100644 arch/arm/mach-k3/Makefile
> create mode 100644 arch/arm/mach-k3/common.c
> create mode 100644 drivers/clk/ti-sci-clk.c
> create mode 100644 drivers/firmware/ti_sci.c
> create mode 100644 drivers/firmware/ti_sci.h
> create mode 100644 drivers/mailbox/Kconfig
> create mode 100644 drivers/mailbox/Makefile
> create mode 100644 drivers/mailbox/mailbox.c
> create mode 100644 drivers/mailbox/ti-msgmgr.c
> create mode 100644 drivers/mci/am654-sdhci.c
> create mode 100644 drivers/soc/ti/Kconfig
> create mode 100644 drivers/soc/ti/Makefile
> create mode 100644 drivers/soc/ti/ti_sci_pm_domains.c
> create mode 100644 images/Makefile.k3
> create mode 100644 images/k3-am625-beagleplay.its
> create mode 100644 include/linux/bsearch.h
> create mode 100644 include/mach/k3/debug_ll.h
> create mode 100644 include/mailbox.h
> create mode 100644 include/soc/ti/k3-sec-proxy.h
> create mode 100644 include/soc/ti/ti_sci_protocol.h
> create mode 100644 lib/bsearch.c
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
next prev parent reply other threads:[~2023-11-02 14:14 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-03 10:49 Sascha Hauer
2023-08-03 10:49 ` [PATCH 01/22] pm_domain: Add onecell support Sascha Hauer
2023-08-03 10:49 ` [PATCH 02/22] gpio: davinci: Redesign driver to accommodate ngpios in one gpio chip Sascha Hauer
2023-08-03 10:49 ` [PATCH 03/22] gpio: davinci: Add support for GPIO controllers on TI K3 SoCs Sascha Hauer
2023-08-03 10:49 ` [PATCH 04/22] ARM64: Add support for debug_ll on TI AM62x SoCs Sascha Hauer
2023-08-03 10:49 ` [PATCH 05/22] Add initial mailbox support Sascha Hauer
2023-08-03 10:49 ` [PATCH 06/22] mailbox: Add TI K3 Secure Proxy Driver Sascha Hauer
2023-08-03 10:49 ` [PATCH 07/22] serial: ns16550: Add support for UARTs on K3 SoCs Sascha Hauer
2023-08-03 10:49 ` [PATCH 08/22] firmware: Add basic support for TI System Control Interface (TI SCI) protocol Sascha Hauer
2023-08-03 10:49 ` [PATCH 09/22] lib: Add generic binary search function Sascha Hauer
2023-08-03 10:49 ` [PATCH 10/22] clk: Add K3 SCI clock driver Sascha Hauer
2023-08-03 10:49 ` [PATCH 11/22] soc: ti: Add ti_sci_pm_domains driver Sascha Hauer
2023-08-03 10:49 ` [PATCH 12/22] mci: fix define Sascha Hauer
2023-08-03 10:49 ` [PATCH 13/22] mci: make debugging output more useful Sascha Hauer
2023-08-03 10:49 ` [PATCH 14/22] mci: sdhci: Add common wait for idle function Sascha Hauer
2023-08-03 10:49 ` [PATCH 15/22] mci: sdhci: wait for idle before stopping clock Sascha Hauer
2023-08-03 10:49 ` [PATCH 16/22] mci: Add am654 SDHCI driver Sascha Hauer
2023-08-03 10:49 ` [PATCH 17/22] ARM: Add Texas Instruments K3 architecture Sascha Hauer
2023-08-03 10:49 ` [PATCH 18/22] ARM: k3: Add initial BeaglePlay board support Sascha Hauer
2023-08-03 10:50 ` [PATCH 19/22] ARM: k3: BeaglePlay: Work around non working SD card Sascha Hauer
2023-08-03 10:50 ` [PATCH 20/22] ARM: k3: BeaglePlay: generate FIT image Sascha Hauer
2023-08-03 10:50 ` [PATCH 21/22] doc: K3: Add documentation Sascha Hauer
2023-08-03 10:50 ` [PATCH 22/22] ARM: multi_v8_defconfig: Enable K3 SoCs Sascha Hauer
2023-11-02 14:12 ` Ahmad Fatoum [this message]
2023-11-03 7:36 ` [PATCH 00/22] Add initial Texas Instruments K3 support Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7b035953-f359-f616-9d90-df37da1890a1@pengutronix.de \
--to=a.fatoum@pengutronix.de \
--cc=barebox@lists.infradead.org \
--cc=s.hauer@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox