mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Michael Riesch <michael.riesch@wolfvision.net>
To: barebox@lists.infradead.org
Cc: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>,
	Michael Riesch <michael.riesch@wolfvision.net>
Subject: [PATCH v2 1/1] gpio: add driver for xilinx zynq and zynqmp
Date: Wed, 13 Oct 2021 13:22:47 +0200	[thread overview]
Message-ID: <20211013112247.3065-2-michael.riesch@wolfvision.net> (raw)
In-Reply-To: <20211013112247.3065-1-michael.riesch@wolfvision.net>

From: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>

Port the driver for the Xilinx Zynq/Zynq UltraScale+ MPSoC architecture
to barebox (based on the Linux driver).

Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
[apply format fixes, revise probe function, revise Kconfig]
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
---
v2:
- add CONFIG_GPIO_ZYNQ=y to zynq{mp}_defconfig
- revise Kconfig
- revise and clean up probe function

 arch/arm/Kconfig                  |   2 +
 arch/arm/configs/zynq_defconfig   |   1 +
 arch/arm/configs/zynqmp_defconfig |   1 +
 drivers/gpio/Kconfig              |   7 +
 drivers/gpio/Makefile             |   1 +
 drivers/gpio/gpio-zynq.c          | 436 ++++++++++++++++++++++++++++++
 6 files changed, 448 insertions(+)
 create mode 100644 drivers/gpio/gpio-zynq.c

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c7ab16688..a8b7bdeaa 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -248,6 +248,7 @@ config ARCH_ZYNQ
 	bool "Xilinx Zynq-based boards"
 	select HAS_DEBUG_LL
 	select PBL_IMAGE
+	select GPIOLIB
 
 config ARCH_ZYNQMP
 	bool "Xilinx ZynqMP-based boards"
@@ -258,6 +259,7 @@ config ARCH_ZYNQMP
 	select COMMON_CLK
 	select COMMON_CLK_OF_PROVIDER
 	select CLKDEV_LOOKUP
+	select GPIOLIB
 	select OFDEVICE
 	select OFTREE
 	select RELOCATABLE
diff --git a/arch/arm/configs/zynq_defconfig b/arch/arm/configs/zynq_defconfig
index a16c57d5c..38662eeb5 100644
--- a/arch/arm/configs/zynq_defconfig
+++ b/arch/arm/configs/zynq_defconfig
@@ -45,3 +45,4 @@ CONFIG_DRIVER_NET_MACB=y
 # CONFIG_PINCTRL is not set
 CONFIG_FS_TFTP=y
 CONFIG_DIGEST=y
+CONFIG_GPIO_ZYNQ=y
diff --git a/arch/arm/configs/zynqmp_defconfig b/arch/arm/configs/zynqmp_defconfig
index 2cd878133..8dd0f40b3 100644
--- a/arch/arm/configs/zynqmp_defconfig
+++ b/arch/arm/configs/zynqmp_defconfig
@@ -64,3 +64,4 @@ CONFIG_FS_NFS=y
 CONFIG_FS_FAT=y
 CONFIG_FS_FAT_WRITE=y
 CONFIG_DIGEST=y
+CONFIG_GPIO_ZYNQ=y
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index f79c9ea67..347a719f5 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -197,6 +197,13 @@ config GPIO_LIBFTDI1
 	bool "libftdi1 driver"
 	depends on SANDBOX
 
+config GPIO_ZYNQ
+	tristate "Xilinx Zynq GPIO support"
+	depends on ARCH_ZYNQ || ARCH_ZYNQMP || CROSS_COMPILE
+	depends on OFDEVICE
+	help
+	  Say yes here to support Xilinx Zynq GPIO controller.
+
 endmenu
 
 endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 023973cb6..d9f96e34c 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -26,3 +26,4 @@ obj-$(CONFIG_GPIO_VF610)	+= gpio-vf610.o
 obj-$(CONFIG_GPIO_RASPBERRYPI_EXP) += gpio-raspberrypi-exp.o
 obj-$(CONFIG_GPIO_SIFIVE)	+= gpio-sifive.o
 obj-$(CONFIG_GPIO_STARFIVE)	+= gpio-starfive-vic.o
+obj-$(CONFIG_GPIO_ZYNQ)		+= gpio-zynq.o
diff --git a/drivers/gpio/gpio-zynq.c b/drivers/gpio/gpio-zynq.c
new file mode 100644
index 000000000..bb7785761
--- /dev/null
+++ b/drivers/gpio/gpio-zynq.c
@@ -0,0 +1,436 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Xilinx Zynq GPIO device driver
+ *
+ * Copyright (C) 2009 - 2014 Xilinx, Inc.
+ *
+ * Based on the Linux kernel driver (drivers/gpio/gpio-zynq.c).
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <gpio.h>
+#include <init.h>
+#include <io.h>
+#include <of.h>
+
+/* Maximum banks */
+#define ZYNQ_GPIO_MAX_BANK	     4
+#define ZYNQMP_GPIO_MAX_BANK	     6
+
+#define ZYNQ_GPIO_BANK0_NGPIO	     32
+#define ZYNQ_GPIO_BANK1_NGPIO	     22
+#define ZYNQ_GPIO_BANK2_NGPIO	     32
+#define ZYNQ_GPIO_BANK3_NGPIO	     32
+
+#define ZYNQMP_GPIO_BANK0_NGPIO	     26
+#define ZYNQMP_GPIO_BANK1_NGPIO	     26
+#define ZYNQMP_GPIO_BANK2_NGPIO	     26
+#define ZYNQMP_GPIO_BANK3_NGPIO	     32
+#define ZYNQMP_GPIO_BANK4_NGPIO	     32
+#define ZYNQMP_GPIO_BANK5_NGPIO	     32
+
+#define ZYNQ_GPIO_NR_GPIOS	     118
+#define ZYNQMP_GPIO_NR_GPIOS	     174
+
+#define ZYNQ_GPIO_BANK0_PIN_MIN(str) 0
+#define ZYNQ_GPIO_BANK0_PIN_MAX(str)                                           \
+	(ZYNQ_GPIO_BANK0_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK0_NGPIO - 1)
+#define ZYNQ_GPIO_BANK1_PIN_MIN(str) (ZYNQ_GPIO_BANK0_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK1_PIN_MAX(str)                                           \
+	(ZYNQ_GPIO_BANK1_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK1_NGPIO - 1)
+#define ZYNQ_GPIO_BANK2_PIN_MIN(str) (ZYNQ_GPIO_BANK1_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK2_PIN_MAX(str)                                           \
+	(ZYNQ_GPIO_BANK2_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK2_NGPIO - 1)
+#define ZYNQ_GPIO_BANK3_PIN_MIN(str) (ZYNQ_GPIO_BANK2_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK3_PIN_MAX(str)                                           \
+	(ZYNQ_GPIO_BANK3_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK3_NGPIO - 1)
+#define ZYNQ_GPIO_BANK4_PIN_MIN(str) (ZYNQ_GPIO_BANK3_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK4_PIN_MAX(str)                                           \
+	(ZYNQ_GPIO_BANK4_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK4_NGPIO - 1)
+#define ZYNQ_GPIO_BANK5_PIN_MIN(str) (ZYNQ_GPIO_BANK4_PIN_MAX(str) + 1)
+#define ZYNQ_GPIO_BANK5_PIN_MAX(str)                                           \
+	(ZYNQ_GPIO_BANK5_PIN_MIN(str) + ZYNQ##str##_GPIO_BANK5_NGPIO - 1)
+
+/* Register offsets for the GPIO device */
+/* LSW Mask & Data -WO */
+#define ZYNQ_GPIO_DATA_LSW_OFFSET(BANK) (0x000 + (8 * BANK))
+/* MSW Mask & Data -WO */
+#define ZYNQ_GPIO_DATA_MSW_OFFSET(BANK) (0x004 + (8 * BANK))
+/* Data Register-RW */
+#define ZYNQ_GPIO_DATA_OFFSET(BANK)	(0x040 + (4 * BANK))
+#define ZYNQ_GPIO_DATA_RO_OFFSET(BANK)	(0x060 + (4 * BANK))
+/* Direction mode reg-RW */
+#define ZYNQ_GPIO_DIRM_OFFSET(BANK)	(0x204 + (0x40 * BANK))
+/* Output enable reg-RW */
+#define ZYNQ_GPIO_OUTEN_OFFSET(BANK)	(0x208 + (0x40 * BANK))
+/* Interrupt mask reg-RO */
+#define ZYNQ_GPIO_INTMASK_OFFSET(BANK)	(0x20C + (0x40 * BANK))
+/* Interrupt enable reg-WO */
+#define ZYNQ_GPIO_INTEN_OFFSET(BANK)	(0x210 + (0x40 * BANK))
+/* Interrupt disable reg-WO */
+#define ZYNQ_GPIO_INTDIS_OFFSET(BANK)	(0x214 + (0x40 * BANK))
+/* Interrupt status reg-RO */
+#define ZYNQ_GPIO_INTSTS_OFFSET(BANK)	(0x218 + (0x40 * BANK))
+/* Interrupt type reg-RW */
+#define ZYNQ_GPIO_INTTYPE_OFFSET(BANK)	(0x21C + (0x40 * BANK))
+/* Interrupt polarity reg-RW */
+#define ZYNQ_GPIO_INTPOL_OFFSET(BANK)	(0x220 + (0x40 * BANK))
+/* Interrupt on any, reg-RW */
+#define ZYNQ_GPIO_INTANY_OFFSET(BANK)	(0x224 + (0x40 * BANK))
+
+/* Disable all interrupts mask */
+#define ZYNQ_GPIO_IXR_DISABLE_ALL	0xFFFFFFFF
+
+/* Mid pin number of a bank */
+#define ZYNQ_GPIO_MID_PIN_NUM		16
+
+/* GPIO upper 16 bit mask */
+#define ZYNQ_GPIO_UPPER_MASK		0xFFFF0000
+
+/* set to differentiate zynq from zynqmp, 0=zynqmp, 1=zynq */
+#define ZYNQ_GPIO_QUIRK_IS_ZYNQ		BIT(0)
+#define GPIO_QUIRK_DATA_RO_BUG		BIT(1)
+
+/**
+ * struct zynq_gpio - GPIO device private data structure
+ * @chip:	instance of the gpio_chip
+ * @base_addr:	base address of the GPIO device
+ * @p_data:	pointer to platform data
+ */
+struct zynq_gpio {
+	struct gpio_chip chip;
+	void __iomem *base_addr;
+	const struct zynq_platform_data *p_data;
+};
+
+/**
+ * struct zynq_platform_data - Zynq GPIO platform data structure
+ * @quirks:	Flags is used to identify the platform
+ * @ngpio:	max number of gpio pins
+ * @max_bank:	maximum number of gpio banks
+ * @bank_min:	this array represents bank's min pin
+ * @bank_max:	this array represents bank's max pin
+ */
+struct zynq_platform_data {
+	u32 quirks;
+	u16 ngpio;
+	int max_bank;
+	int bank_min[ZYNQMP_GPIO_MAX_BANK];
+	int bank_max[ZYNQMP_GPIO_MAX_BANK];
+};
+
+/**
+ * zynq_gpio_is_zynq - Test if HW is Zynq or ZynqMP
+ * @gpio:	Pointer to driver data struct
+ *
+ * Return: 0 if ZynqMP, 1 if Zynq.
+ */
+static int zynq_gpio_is_zynq(struct zynq_gpio *gpio)
+{
+	return !!(gpio->p_data->quirks & ZYNQ_GPIO_QUIRK_IS_ZYNQ);
+}
+
+/**
+ * gpio_data_ro_bug - Test if HW bug exists or not
+ * @gpio:       Pointer to driver data struct
+ *
+ * Return: 0 if bug does not exist, 1 if bug exists.
+ */
+static int gpio_data_ro_bug(struct zynq_gpio *gpio)
+{
+	return !!(gpio->p_data->quirks & GPIO_QUIRK_DATA_RO_BUG);
+}
+
+/**
+ * zynq_gpio_get_bank_pin - Get the bank number and pin number within that bank
+ * for a given pin in the GPIO device
+ * @pin_num:	gpio pin number within the device
+ * @bank_num:	an output parameter used to return the bank number of the gpio
+ *		pin
+ * @bank_pin_num: an output parameter used to return pin number within a bank
+ *		  for the given gpio pin
+ * @gpio:	gpio device data structure
+ *
+ * Returns the bank number and pin offset within the bank.
+ */
+static int zynq_gpio_get_bank_pin(unsigned int pin_num, unsigned int *bank_num,
+				  unsigned int *bank_pin_num,
+				  struct zynq_gpio *gpio)
+{
+	int bank;
+
+	for (bank = 0; bank < gpio->p_data->max_bank; bank++) {
+		if ((pin_num >= gpio->p_data->bank_min[bank]) &&
+		    (pin_num <= gpio->p_data->bank_max[bank])) {
+			*bank_num = bank;
+			*bank_pin_num = pin_num - gpio->p_data->bank_min[bank];
+			return 0;
+		}
+	}
+
+	*bank_num = 0;
+	*bank_pin_num = 0;
+	return -ENODEV;
+}
+
+/**
+ * zynq_gpio_get_value - Get the state of the specified pin of GPIO device
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ *
+ * This function reads the state of the specified pin of the GPIO device.
+ *
+ * Return: 0 if the pin is low, 1 if pin is high.
+ */
+static int zynq_gpio_get_value(struct gpio_chip *chip, unsigned int pin)
+{
+	u32 data;
+	unsigned int bank_num, bank_pin_num;
+	struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+	if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+		return -EINVAL;
+
+	if (gpio_data_ro_bug(gpio)) {
+		if (zynq_gpio_is_zynq(gpio)) {
+			if (bank_num <= 1) {
+				data = readl_relaxed(
+					gpio->base_addr +
+					ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
+			} else {
+				data = readl_relaxed(
+					gpio->base_addr +
+					ZYNQ_GPIO_DATA_OFFSET(bank_num));
+			}
+		} else {
+			if (bank_num <= 2) {
+				data = readl_relaxed(
+					gpio->base_addr +
+					ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
+			} else {
+				data = readl_relaxed(
+					gpio->base_addr +
+					ZYNQ_GPIO_DATA_OFFSET(bank_num));
+			}
+		}
+	} else {
+		data = readl_relaxed(gpio->base_addr +
+				     ZYNQ_GPIO_DATA_RO_OFFSET(bank_num));
+	}
+	return (data >> bank_pin_num) & 1;
+}
+
+/**
+ * zynq_gpio_set_value - Modify the state of the pin with specified value
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ * @state:	value used to modify the state of the specified pin
+ *
+ * This function calculates the register offset (i.e to lower 16 bits or
+ * upper 16 bits) based on the given pin number and sets the state of a
+ * gpio pin to the specified value. The state is either 0 or non-zero.
+ */
+static void zynq_gpio_set_value(struct gpio_chip *chip, unsigned int pin,
+				int state)
+{
+	unsigned int reg_offset, bank_num, bank_pin_num;
+	struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+	if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+		return;
+
+	if (bank_pin_num >= ZYNQ_GPIO_MID_PIN_NUM) {
+		bank_pin_num -= ZYNQ_GPIO_MID_PIN_NUM;
+		reg_offset = ZYNQ_GPIO_DATA_MSW_OFFSET(bank_num);
+	} else {
+		reg_offset = ZYNQ_GPIO_DATA_LSW_OFFSET(bank_num);
+	}
+
+	/*
+	 * get the 32 bit value to be written to the mask/data register where
+	 * the upper 16 bits is the mask and lower 16 bits is the data
+	 */
+	state = !!state;
+	state = ~(1 << (bank_pin_num + ZYNQ_GPIO_MID_PIN_NUM)) &
+		((state << bank_pin_num) | ZYNQ_GPIO_UPPER_MASK);
+
+	writel_relaxed(state, gpio->base_addr + reg_offset);
+}
+
+/**
+ * zynq_gpio_dir_in - Set the direction of the specified GPIO pin as input
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ *
+ * This function uses the read-modify-write sequence to set the direction of
+ * the gpio pin as input.
+ *
+ * Return: 0 always
+ */
+static int zynq_gpio_dir_in(struct gpio_chip *chip, unsigned int pin)
+{
+	u32 reg;
+	unsigned int bank_num, bank_pin_num;
+	struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+	if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+		return -EINVAL;
+	/*
+	 * On zynq bank 0 pins 7 and 8 are special and cannot be used
+	 * as inputs.
+	 */
+	if (zynq_gpio_is_zynq(gpio) && bank_num == 0 &&
+	    (bank_pin_num == 7 || bank_pin_num == 8))
+		return -EINVAL;
+
+	/* clear the bit in direction mode reg to set the pin as input */
+	reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+	reg &= ~BIT(bank_pin_num);
+	writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+
+	return 0;
+}
+
+/**
+ * zynq_gpio_dir_out - Set the direction of the specified GPIO pin as output
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ * @state:	value to be written to specified pin
+ *
+ * This function sets the direction of specified GPIO pin as output, configures
+ * the Output Enable register for the pin and uses zynq_gpio_set to set
+ * the state of the pin to the value specified.
+ *
+ * Return: 0 always
+ */
+static int zynq_gpio_dir_out(struct gpio_chip *chip, unsigned int pin,
+			     int state)
+{
+	u32 reg;
+	unsigned int bank_num, bank_pin_num;
+	struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+	if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+		return -EINVAL;
+
+	/* set the GPIO pin as output */
+	reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+	reg |= BIT(bank_pin_num);
+	writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+
+	/* configure the output enable reg for the pin */
+	reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_OUTEN_OFFSET(bank_num));
+	reg |= BIT(bank_pin_num);
+	writel_relaxed(reg, gpio->base_addr + ZYNQ_GPIO_OUTEN_OFFSET(bank_num));
+
+	/* set the state of the pin */
+	zynq_gpio_set_value(chip, pin, state);
+	return 0;
+}
+
+/**
+ * zynq_gpio_get_direction - Read the direction of the specified GPIO pin
+ * @chip:	gpio_chip instance to be worked on
+ * @pin:	gpio pin number within the device
+ *
+ * This function returns the direction of the specified GPIO.
+ *
+ * Return: 0 for output, 1 for input
+ */
+static int zynq_gpio_get_direction(struct gpio_chip *chip, unsigned int pin)
+{
+	u32 reg;
+	unsigned int bank_num, bank_pin_num;
+	struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip);
+
+	if (zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio) < 0)
+		return -EINVAL;
+
+	reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num));
+
+	return !(reg & BIT(bank_pin_num));
+}
+
+static struct gpio_ops zynq_gpio_ops = {
+	.direction_input = zynq_gpio_dir_in,
+	.direction_output = zynq_gpio_dir_out,
+	.get = zynq_gpio_get_value,
+	.set = zynq_gpio_set_value,
+	.get_direction = zynq_gpio_get_direction,
+};
+
+static int zynqmp_gpio_probe(struct device_d *dev)
+{
+	struct resource *iores;
+	struct zynq_gpio *gpio;
+	const struct zynq_platform_data *p_data;
+	int ret;
+
+	gpio = xzalloc(sizeof(*gpio));
+	p_data = device_get_match_data(dev);
+	iores = dev_request_mem_resource(dev, 0);
+	if (IS_ERR(iores)) {
+		ret = PTR_ERR(iores);
+		goto free_gpio;
+	}
+
+	gpio->base_addr = IOMEM(iores->start);
+	gpio->chip.base = of_alias_get_id(dev->device_node, "gpio");
+	gpio->chip.ops = &zynq_gpio_ops;
+	gpio->chip.ngpio = p_data->ngpio;
+	gpio->chip.dev = dev;
+	gpio->p_data = p_data;
+
+	return gpiochip_add(&gpio->chip);
+
+free_gpio:
+	kfree(gpio);
+	return ret;
+}
+
+static const struct zynq_platform_data zynqmp_gpio_def = {
+	.quirks = GPIO_QUIRK_DATA_RO_BUG,
+	.ngpio = ZYNQMP_GPIO_NR_GPIOS,
+	.max_bank = ZYNQMP_GPIO_MAX_BANK,
+	.bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(MP),
+	.bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(MP),
+	.bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(MP),
+	.bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(MP),
+	.bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(MP),
+	.bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(MP),
+	.bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(MP),
+	.bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(MP),
+	.bank_min[4] = ZYNQ_GPIO_BANK4_PIN_MIN(MP),
+	.bank_max[4] = ZYNQ_GPIO_BANK4_PIN_MAX(MP),
+	.bank_min[5] = ZYNQ_GPIO_BANK5_PIN_MIN(MP),
+	.bank_max[5] = ZYNQ_GPIO_BANK5_PIN_MAX(MP),
+};
+
+static const struct zynq_platform_data zynq_gpio_def = {
+	.quirks = ZYNQ_GPIO_QUIRK_IS_ZYNQ | GPIO_QUIRK_DATA_RO_BUG,
+	.ngpio = ZYNQ_GPIO_NR_GPIOS,
+	.max_bank = ZYNQ_GPIO_MAX_BANK,
+	.bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(),
+	.bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(),
+	.bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(),
+	.bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(),
+	.bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(),
+	.bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(),
+	.bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(),
+	.bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(),
+};
+
+static const struct of_device_id zynq_gpio_of_match[] = {
+	{ .compatible = "xlnx,zynq-gpio-1.0", .data = &zynq_gpio_def },
+	{ .compatible = "xlnx,zynqmp-gpio-1.0", .data = &zynqmp_gpio_def },
+	{ /* end of table */ }
+};
+
+static struct driver_d zynqmp_gpio_driver = {
+	.name = "zynqmp-gpio",
+	.of_compatible = zynq_gpio_of_match,
+	.probe = zynqmp_gpio_probe,
+};
+
+postcore_platform_driver(zynqmp_gpio_driver);
-- 
2.17.1


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox


  reply	other threads:[~2021-10-13 12:43 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-10-13 11:22 [PATCH v2 0/1] " Michael Riesch
2021-10-13 11:22 ` Michael Riesch [this message]
2021-10-14 11:57 ` Sascha Hauer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20211013112247.3065-2-michael.riesch@wolfvision.net \
    --to=michael.riesch@wolfvision.net \
    --cc=barebox@lists.infradead.org \
    --cc=thomas.haemmerle@wolfvision.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox