mail archive of the barebox mailing list
 help / color / mirror / Atom feed
From: Ahmad Fatoum <a.fatoum@pengutronix.de>
To: barebox@lists.infradead.org
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Subject: [PATCH v3 3/6] clk: imx6: remove quirky clk_set_parent(LDB_diN_sel, pll5_video_div)
Date: Wed, 17 Jul 2019 19:06:01 +0200	[thread overview]
Message-ID: <20190717170604.23732-4-a.fatoum@pengutronix.de> (raw)
In-Reply-To: <20190717170604.23732-1-a.fatoum@pengutronix.de>

barebox has inherited the clk_set_parent(ldb_diN_sel, pll5_video_div)
from upstream kernel commit 32f3b8da22 ("ARM i.MX6q: set the LDB serial
clock parent to the video PLL"), where it was enabled for all i.MX6Q
revisions after 1.0. It was applied whenever CONFIG_DRIVER_VIDEO_IMX_IPUV3
was defined.

The kernel removed this reparenting again as a preventive measure
against ERR009219 in 03d576f202 ("clk: imx6: Make the LDB_DI0 and
LDB_DI1 clocks read-only").

In barebox, the reparenting remains and is done for all i.MX6 SoCs
with a revision > 1.0. On all of them, except for the QuadPlus and
the DualPlus, this reparenting may glitch the LDB so that it
permanently locks up.

By removing the reparenting in this commit, producing this glitch is
avoided. The device tree[1] can elect to reinstate the reparenting:

	&clks {
		assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
				  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
		assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
					 <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
	};

Follow-up patches will explicitly check for this and do reparenting
defined this way in a glitch-free manner.

As of v2019.07.0, following mainline boards are potentially broken
by this (i.e. they're supported by barebox, are in the list above,
had a LDB enabled and might be defining CONFIG_DRIVER_VIDEO_IMX_IPUV3):
  - imx6qdl-zii-rdu2.dtsi
  - imx6qdl-udoo.dtsi
  - imx6qdl-mba6x.dtsi
  - imx6q-var-custom.dts
  - imx6q-guf-santaro.dts
  - imx6q-embedsky-e9.dtsi

[1]: If barebox is configured to show a boot splash screen, this snippet
     should exist in the barebox device tree. If barebox acts on it, the
     kernel will show following warning:
         ccm: ldb_di0_sel already changed from reset value: 0
         ccm: ldb_di1_sel already changed from reset value: 0
     This warning is safe to ignore.

Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Raphael Poggi <poggi.raph@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
 drivers/clk/imx/clk-imx6.c | 6 ------
 1 file changed, 6 deletions(-)

diff --git a/drivers/clk/imx/clk-imx6.c b/drivers/clk/imx/clk-imx6.c
index d23b7e277bdf..6f19535be7ba 100644
--- a/drivers/clk/imx/clk-imx6.c
+++ b/drivers/clk/imx/clk-imx6.c
@@ -356,12 +356,6 @@ static void imx6_add_video_clks(void __iomem *anab, void __iomem *cb)
 	clk_set_parent(clks[IMX6QDL_CLK_IPU1_DI1_PRE_SEL], clks[IMX6QDL_CLK_PLL5_VIDEO_DIV]);
 	clk_set_parent(clks[IMX6QDL_CLK_IPU2_DI0_PRE_SEL], clks[IMX6QDL_CLK_PLL5_VIDEO_DIV]);
 	clk_set_parent(clks[IMX6QDL_CLK_IPU2_DI1_PRE_SEL], clks[IMX6QDL_CLK_PLL5_VIDEO_DIV]);
-
-	if (imx_silicon_revision() != IMX_CHIP_REV_1_0) {
-		clk_set_parent(clks[IMX6QDL_CLK_LDB_DI0_SEL], clks[IMX6QDL_CLK_PLL5_VIDEO_DIV]);
-		clk_set_parent(clks[IMX6QDL_CLK_LDB_DI1_SEL], clks[IMX6QDL_CLK_PLL5_VIDEO_DIV]);
-	}
-
 }
 
 static int imx6_ccm_probe(struct device_d *dev)
-- 
2.20.1


_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox

  parent reply	other threads:[~2019-07-17 17:06 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-17 17:05 [PATCH v3 0/6] clk: imx6: work around LDB hang caused by ERR009219 Ahmad Fatoum
2019-07-17 17:05 ` [PATCH v3 1/6] clk: imx6: fix use of cpu_is_mx6* before they are initialized Ahmad Fatoum
2019-07-17 17:10   ` Ahmad Fatoum
2019-07-18 15:51     ` Ahmad Fatoum
2019-07-17 17:06 ` [PATCH v3 2/6] clk: imx6: Mask mmdc_ch1 handshake for periph2_sel and mmdc_ch1_axi_podf Ahmad Fatoum
2019-07-17 17:06 ` Ahmad Fatoum [this message]
2019-07-17 17:06 ` [PATCH v3 4/6] clk: imx6: Make the LDB_DI0 and LDB_DI1 clocks read-only Ahmad Fatoum
2019-07-18  8:19   ` Roland Hieber
2019-07-18  8:25     ` Ahmad Fatoum
2019-07-18  8:33       ` Roland Hieber
2019-08-05 10:22       ` Sascha Hauer
2019-07-17 17:06 ` [PATCH v3 5/6] clk: imx6: Fix procedure to switch the parent of LDB_DI_CLK Ahmad Fatoum
2019-09-10 13:15   ` Sascha Hauer
2019-09-10 14:07     ` Ahmad Fatoum
2019-07-17 17:06 ` [PATCH v3 6/6] clk: imx6: define an enum for ldb mux inputs Ahmad Fatoum

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190717170604.23732-4-a.fatoum@pengutronix.de \
    --to=a.fatoum@pengutronix.de \
    --cc=andrew.smirnov@gmail.com \
    --cc=barebox@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox